X-Git-Url: http://git.droids-corp.org/?a=blobdiff_plain;f=lib%2Flibrte_ether%2Frte_ethdev.h;h=f860601082ede0bc7a13292aa35be174571b6419;hb=3031749c2df04a63cdcef186dcce3781e61436e8;hp=55a4e42f4ed5a1aabbf008a426fa94d140bd856f;hpb=81f9db8ecc2cf7798cc3b38b01c42d0de9bca611;p=dpdk.git diff --git a/lib/librte_ether/rte_ethdev.h b/lib/librte_ether/rte_ethdev.h index 55a4e42f4e..f860601082 100644 --- a/lib/librte_ether/rte_ethdev.h +++ b/lib/librte_ether/rte_ethdev.h @@ -1,35 +1,34 @@ /*- * BSD LICENSE - * - * Copyright(c) 2010-2012 Intel Corporation. All rights reserved. + * + * Copyright(c) 2010-2014 Intel Corporation. All rights reserved. * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions * are met: - * - * * Redistributions of source code must retain the above copyright + * + * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. - * * Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in - * the documentation and/or other materials provided with the + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the * distribution. - * * Neither the name of Intel Corporation nor the names of its - * contributors may be used to endorse or promote products derived + * * Neither the name of Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * */ #ifndef _RTE_ETHDEV_H_ @@ -193,6 +192,10 @@ struct rte_eth_stats { uint64_t rx_nombuf; /**< Total number of RX mbuf allocation failures. */ uint64_t fdirmatch; /**< Total number of RX packets matching a filter. */ uint64_t fdirmiss; /**< Total number of RX packets not matching any filter. */ + uint64_t tx_pause_xon; /**< Total nb. of XON pause frame sent. */ + uint64_t rx_pause_xon; /**< Total nb. of XON pause frame received. */ + uint64_t tx_pause_xoff; /**< Total nb. of XOFF pause frame sent. */ + uint64_t rx_pause_xoff; /**< Total nb. of XOFF pause frame received. */ uint64_t q_ipackets[RTE_ETHDEV_QUEUE_STAT_CNTRS]; /**< Total number of queue RX packets. */ uint64_t q_opackets[RTE_ETHDEV_QUEUE_STAT_CNTRS]; @@ -203,6 +206,14 @@ struct rte_eth_stats { /**< Total number of successfully transmitted queue bytes. */ uint64_t q_errors[RTE_ETHDEV_QUEUE_STAT_CNTRS]; /**< Total number of queue packets received that are dropped. */ + uint64_t ilbpackets; + /**< Total number of good packets received from loopback,VF Only */ + uint64_t olbpackets; + /**< Total number of good packets transmitted to loopback,VF Only */ + uint64_t ilbbytes; + /**< Total number of good bytes received from loopback,VF Only */ + uint64_t olbbytes; + /**< Total number of good bytes transmitted to loopback,VF Only */ }; /** @@ -239,21 +250,43 @@ struct rte_eth_thresh { * packets to multiple queues. */ enum rte_eth_rx_mq_mode { - ETH_RSS = 0, /**< Default to RSS mode */ - ETH_VMDQ_DCB, /**< Use VMDQ+DCB to route traffic to queues */ - ETH_DCB_RX /**< For RX side,only DCB is on. */ + ETH_MQ_RX_NONE = 0, /**< None of DCB,RSS or VMDQ mode */ + + ETH_MQ_RX_RSS, /**< For RX side, only RSS is on */ + ETH_MQ_RX_DCB, /**< For RX side,only DCB is on. */ + ETH_MQ_RX_DCB_RSS, /**< Both DCB and RSS enable */ + + ETH_MQ_RX_VMDQ_ONLY, /**< Only VMDQ, no RSS nor DCB */ + ETH_MQ_RX_VMDQ_RSS, /**< RSS mode with VMDQ */ + ETH_MQ_RX_VMDQ_DCB, /**< Use VMDQ+DCB to route traffic to queues */ + ETH_MQ_RX_VMDQ_DCB_RSS, /**< Enable both VMDQ and DCB in VMDq */ }; /** - * A set of values to identify what method is to be used to transmit + * for rx mq mode backward compatible + */ +#define ETH_RSS ETH_MQ_RX_RSS +#define VMDQ_DCB ETH_MQ_RX_VMDQ_DCB +#define ETH_DCB_RX ETH_MQ_RX_DCB + +/** + * A set of values to identify what method is to be used to transmit * packets using multi-TCs. */ enum rte_eth_tx_mq_mode { - ETH_DCB_NONE = 0, /**< It is not in DCB mode. */ - ETH_VMDQ_DCB_TX, /**< For TX side,both DCB and VT is on. */ - ETH_DCB_TX /**< For TX side,only DCB is on. */ + ETH_MQ_TX_NONE = 0, /**< It is in neither DCB nor VT mode. */ + ETH_MQ_TX_DCB, /**< For TX side,only DCB is on. */ + ETH_MQ_TX_VMDQ_DCB, /**< For TX side,both DCB and VT is on. */ + ETH_MQ_TX_VMDQ_ONLY, /**< Only VT on, no DCB */ }; +/** + * for tx mq mode backward compatible + */ +#define ETH_DCB_NONE ETH_MQ_TX_NONE +#define ETH_VMDQ_DCB_TX ETH_MQ_TX_VMDQ_DCB +#define ETH_DCB_TX ETH_MQ_TX_DCB + /** * A structure used to configure the RX features of an Ethernet port. */ @@ -299,6 +332,11 @@ struct rte_eth_rss_conf { #define ETH_RSS_IPV6_UDP 0x0080 /**< IPv6/UDP packet. */ #define ETH_RSS_IPV6_UDP_EX 0x0100 /**< IPv6/UDP with extension headers. */ +#define ETH_RSS_PROTO_MASK 0x01FF /**< Mask of valid RSS hash protocols */ +/* Definitions used for redirection table entry size */ +#define ETH_RSS_RETA_NUM_ENTRIES 128 +#define ETH_RSS_RETA_MAX_QUEUE 16 + /* Definitions used for VMDQ and DCB functionality */ #define ETH_VMDQ_MAX_VLAN_FILTERS 64 /**< Maximum nb. of VMDQ vlan filters. */ #define ETH_DCB_NUM_USER_PRIORITIES 8 /**< Maximum nb. of DCB priorities. */ @@ -307,7 +345,7 @@ struct rte_eth_rss_conf { /* DCB capability defines */ #define ETH_DCB_PG_SUPPORT 0x00000001 /**< Priority Group(ETS) support. */ -#define ETH_DCB_PFC_SUPPORT 0x00000002 /**< Priority Flow Control support. */ +#define ETH_DCB_PFC_SUPPORT 0x00000002 /**< Priority Flow Control support. */ /* Definitions used for VLAN Offload functionality */ #define ETH_VLAN_STRIP_OFFLOAD 0x0001 /**< VLAN Strip On/Off */ @@ -318,6 +356,60 @@ struct rte_eth_rss_conf { #define ETH_VLAN_STRIP_MASK 0x0001 /**< VLAN Strip setting mask */ #define ETH_VLAN_FILTER_MASK 0x0002 /**< VLAN Filter setting mask*/ #define ETH_VLAN_EXTEND_MASK 0x0004 /**< VLAN Extend setting mask*/ +#define ETH_VLAN_ID_MAX 0x0FFF /**< VLAN ID is in lower 12 bits*/ + +/* Definitions used for receive MAC address */ +#define ETH_NUM_RECEIVE_MAC_ADDR 128 /**< Maximum nb. of receive mac addr. */ + + +/* Definitions used for unicast hash */ +#define ETH_VMDQ_NUM_UC_HASH_ARRAY 128 /**< Maximum nb. of UC hash array. */ + +/* Definitions used for VMDQ pool rx mode setting */ +#define ETH_VMDQ_ACCEPT_UNTAG 0x0001 /**< accept untagged packets. */ +#define ETH_VMDQ_ACCEPT_HASH_MC 0x0002 /**< accept packets in multicast table . */ +#define ETH_VMDQ_ACCEPT_HASH_UC 0x0004 /**< accept packets in unicast table. */ +#define ETH_VMDQ_ACCEPT_BROADCAST 0x0008 /**< accept broadcast packets. */ +#define ETH_VMDQ_ACCEPT_MULTICAST 0x0010 /**< multicast promiscuous. */ + +/* Definitions used for VMDQ mirror rules setting */ +#define ETH_VMDQ_NUM_MIRROR_RULE 4 /**< Maximum nb. of mirror rules. . */ + +#define ETH_VMDQ_POOL_MIRROR 0x0001 /**< Virtual Pool Mirroring. */ +#define ETH_VMDQ_UPLINK_MIRROR 0x0002 /**< Uplink Port Mirroring. */ +#define ETH_VMDQ_DOWNLIN_MIRROR 0x0004 /**< Downlink Port Mirroring. */ +#define ETH_VMDQ_VLAN_MIRROR 0x0008 /**< VLAN Mirroring. */ + +/** + * A structure used to configure VLAN traffic mirror of an Ethernet port. + */ +struct rte_eth_vlan_mirror { + uint64_t vlan_mask; /**< mask for valid VLAN ID. */ + uint16_t vlan_id[ETH_VMDQ_MAX_VLAN_FILTERS]; + /** VLAN ID list for vlan mirror. */ +}; + +/** + * A structure used to configure traffic mirror of an Ethernet port. + */ +struct rte_eth_vmdq_mirror_conf { + uint8_t rule_type_mask; /**< Mirroring rule type mask we want to set */ + uint8_t dst_pool; /**< Destination pool for this mirror rule. */ + uint64_t pool_mask; /**< Bitmap of pool for pool mirroring */ + struct rte_eth_vlan_mirror vlan; /**< VLAN ID setting for VLAN mirroring */ +}; + +/** + * A structure used to configure Redirection Table of the Receive Side + * Scaling (RSS) feature of an Ethernet port. + */ +struct rte_eth_rss_reta { + /** First 64 mask bits indicate which entry(s) need to updated/queried. */ + uint64_t mask_lo; + /** Second 64 mask bits indicate which entry(s) need to updated/queried. */ + uint64_t mask_hi; + uint8_t reta[ETH_RSS_RETA_NUM_ENTRIES]; /**< 128 RETA entries*/ +}; /** * This enum indicates the possible number of traffic classes @@ -330,11 +422,13 @@ enum rte_eth_nb_tcs { /** * This enum indicates the possible number of queue pools - * in VMDQ+DCB configurations. + * in VMDQ configurations. */ enum rte_eth_nb_pools { - ETH_16_POOLS = 16, /**< 16 pools with DCB. */ - ETH_32_POOLS = 32 /**< 32 pools with DCB. */ + ETH_8_POOLS = 8, /**< 8 VMDq pools. */ + ETH_16_POOLS = 16, /**< 16 VMDq pools. */ + ETH_32_POOLS = 32, /**< 32 VMDq pools. */ + ETH_64_POOLS = 64 /**< 64 VMDq pools. */ }; /* This structure may be extended in future. */ @@ -343,19 +437,23 @@ struct rte_eth_dcb_rx_conf { uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES]; /**< Possible DCB queue,4 or 8. */ }; - + struct rte_eth_vmdq_dcb_tx_conf { enum rte_eth_nb_pools nb_queue_pools; /**< With DCB, 16 or 32 pools. */ uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES]; /**< Possible DCB queue,4 or 8. */ }; - + struct rte_eth_dcb_tx_conf { - enum rte_eth_nb_tcs nb_tcs; /**< possible DCB TCs, 4 or 8 TCs. */ + enum rte_eth_nb_tcs nb_tcs; /**< Possible DCB TCs, 4 or 8 TCs. */ uint8_t dcb_queue[ETH_DCB_NUM_USER_PRIORITIES]; /**< Possible DCB queue,4 or 8. */ }; +struct rte_eth_vmdq_tx_conf { + enum rte_eth_nb_pools nb_queue_pools; /**< VMDq mode, 64 pools. */ +}; + /** * A structure used to configure the VMDQ+DCB feature * of an Ethernet port. @@ -380,6 +478,18 @@ struct rte_eth_vmdq_dcb_conf { /**< Selects a queue in a pool */ }; +struct rte_eth_vmdq_rx_conf { + enum rte_eth_nb_pools nb_queue_pools; /**< VMDq only mode, 8 or 64 pools */ + uint8_t enable_default_pool; /**< If non-zero, use a default pool */ + uint8_t default_pool; /**< The default pool, if applicable */ + uint8_t enable_loop_back; /**< Enable VT loop back */ + uint8_t nb_pool_maps; /**< We can have up to 64 filters/mappings */ + struct { + uint16_t vlan_id; /**< The vlan id of the received frame */ + uint64_t pools; /**< Bitmask of pools for packet rx */ + } pool_map[ETH_VMDQ_MAX_VLAN_FILTERS]; /**< VMDq vlan pool maps. */ +}; + /** * A structure used to configure the TX features of an Ethernet port. */ @@ -394,6 +504,7 @@ struct rte_eth_rxconf { struct rte_eth_thresh rx_thresh; /**< RX ring threshold registers. */ uint16_t rx_free_thresh; /**< Drives the freeing of RX descriptors. */ uint8_t rx_drop_en; /**< Drop packets if no descriptors are available. */ + uint8_t start_rx_per_q; /**< start rx per queue. */ }; #define ETH_TXQ_FLAGS_NOMULTSEGS 0x0001 /**< nb_segs=1 for all mbufs */ @@ -414,6 +525,7 @@ struct rte_eth_txconf { uint16_t tx_rs_thresh; /**< Drives the setting of RS bit on TXDs. */ uint16_t tx_free_thresh; /**< Drives the freeing of TX buffers. */ uint32_t txq_flags; /**< Set flags for the Tx queue */ + uint8_t start_tx_per_q; /**< start tx per queue. */ }; /** @@ -437,6 +549,17 @@ struct rte_eth_fc_conf { uint16_t pause_time; /**< Pause quota in the Pause frame */ uint16_t send_xon; /**< Is XON frame need be sent */ enum rte_eth_fc_mode mode; /**< Link flow control mode */ + uint8_t mac_ctrl_frame_fwd; /**< Forward MAC control frames */ +}; + +/** + * A structure used to configure Ethernet priority flow control parameter. + * These parameters will be configured into the register of the NIC. + * Please refer to the corresponding data sheet for proper value. + */ +struct rte_eth_pfc_conf { + struct rte_eth_fc_conf fc; /**< General flow control parameter. */ + uint8_t priority; /**< VLAN User Priority. */ }; /** @@ -477,9 +600,9 @@ struct rte_fdir_conf { enum rte_fdir_mode mode; /**< Flow Director mode. */ enum rte_fdir_pballoc_type pballoc; /**< Space for FDIR filters. */ enum rte_fdir_status_mode status; /**< How to report FDIR hash. */ - /* Offset of flexbytes field in RX packets (in 16-bit word units). */ + /** Offset of flexbytes field in RX packets (in 16-bit word units). */ uint8_t flexbytes_offset; - /* RX queue of packets matching a "drop" filter in perfect mode. */ + /** RX queue of packets matching a "drop" filter in perfect mode. */ uint8_t drop_queue; }; @@ -537,6 +660,11 @@ struct rte_fdir_masks { uint8_t vlan_prio; /** If set to 1, flexbytes is relevant in filters. */ uint8_t flexbytes; + /** If set to 1, set the IPv6 masks. Otherwise set the IPv4 masks. */ + uint8_t set_ipv6_mask; + /** When set to 1, comparison of destination IPv6 address with IP6AT + registers is meaningful. */ + uint8_t comp_ipv6_dst; /** Mask of Destination IPv4 Address. All bits set to 1 define the relevant bits to use in the destination address of an IPv4 packet when matching it against FDIR filters. */ @@ -548,6 +676,10 @@ struct rte_fdir_masks { /** Mask of Source IPv6 Address. All bits set to 1 define the relevant BYTES to use in the source address of an IPv6 packet when matching it against FDIR filters. */ + uint16_t dst_ipv6_mask; + /** Mask of Destination IPv6 Address. All bits set to 1 define the + relevant BYTES to use in the destination address of an IPv6 packet + when matching it against FDIR filters. */ uint16_t src_ipv6_mask; /** Mask of Source Port. All bits set to 1 define the relevant bits to use in the source port of an IP packets when matching it @@ -602,22 +734,31 @@ struct rte_eth_conf { /**< ETH_LINK_[HALF_DUPLEX|FULL_DUPLEX], or 0 for autonegotation */ struct rte_eth_rxmode rxmode; /**< Port RX configuration. */ struct rte_eth_txmode txmode; /**< Port TX configuration. */ + uint32_t lpbk_mode; /**< Loopback operation mode. By default the value + is 0, meaning the loopback mode is disabled. + Read the datasheet of given ethernet controller + for details. The possible values of this field + are defined in implementation of each driver. */ union { struct rte_eth_rss_conf rss_conf; /**< Port RSS configuration */ struct rte_eth_vmdq_dcb_conf vmdq_dcb_conf; /**< Port vmdq+dcb configuration. */ struct rte_eth_dcb_rx_conf dcb_rx_conf; /**< Port dcb RX configuration. */ + struct rte_eth_vmdq_rx_conf vmdq_rx_conf; + /**< Port vmdq RX configuration. */ } rx_adv_conf; /**< Port RX filtering configuration (union). */ union { struct rte_eth_vmdq_dcb_tx_conf vmdq_dcb_tx_conf; /**< Port vmdq+dcb TX configuration. */ struct rte_eth_dcb_tx_conf dcb_tx_conf; /**< Port dcb TX configuration. */ + struct rte_eth_vmdq_tx_conf vmdq_tx_conf; + /**< Port vmdq TX configuration. */ } tx_adv_conf; /**< Port TX DCB configuration (union). */ - /** Currently,Priority Flow Control(PFC) are supported,if DCB with PFC - is needed,and the variable must be set ETH_DCB_PFC_SUPPORT. */ - uint32_t dcb_capability_en; + /** Currently,Priority Flow Control(PFC) are supported,if DCB with PFC + is needed,and the variable must be set ETH_DCB_PFC_SUPPORT. */ + uint32_t dcb_capability_en; struct rte_fdir_conf fdir_conf; /**< FDIR configuration. */ struct rte_intr_conf intr_conf; /**< Interrupt mode configuration. */ }; @@ -627,14 +768,43 @@ struct rte_eth_conf { * an Ethernet device, such as the controlling driver of the device, * its PCI context, etc... */ + +/** + * RX offload capabilities of a device. + */ +#define DEV_RX_OFFLOAD_VLAN_STRIP 0x00000001 +#define DEV_RX_OFFLOAD_IPV4_CKSUM 0x00000002 +#define DEV_RX_OFFLOAD_UDP_CKSUM 0x00000004 +#define DEV_RX_OFFLOAD_TCP_CKSUM 0x00000008 +#define DEV_RX_OFFLOAD_TCP_LRO 0x00000010 + +/** + * TX offload capabilities of a device. + */ +#define DEV_TX_OFFLOAD_VLAN_INSERT 0x00000001 +#define DEV_TX_OFFLOAD_IPV4_CKSUM 0x00000002 +#define DEV_TX_OFFLOAD_UDP_CKSUM 0x00000004 +#define DEV_TX_OFFLOAD_TCP_CKSUM 0x00000008 +#define DEV_TX_OFFLOAD_SCTP_CKSUM 0x00000010 +#define DEV_TX_OFFLOAD_TCP_TSO 0x00000020 +#define DEV_TX_OFFLOAD_UDP_TSO 0x00000040 + struct rte_eth_dev_info { struct rte_pci_device *pci_dev; /**< Device PCI information. */ const char *driver_name; /**< Device Driver name. */ + unsigned int if_index; /**< Index to bound host interface, or 0 if none. + Use if_indextoname() to translate into an interface name. */ uint32_t min_rx_bufsize; /**< Minimum size of RX buffer. */ uint32_t max_rx_pktlen; /**< Maximum configurable length of RX pkt. */ uint16_t max_rx_queues; /**< Maximum number of RX queues. */ uint16_t max_tx_queues; /**< Maximum number of TX queues. */ uint32_t max_mac_addrs; /**< Maximum number of MAC addresses. */ + uint32_t max_hash_mac_addrs; + /** Maximum number of hash MAC addresses for MTA and UTA. */ + uint16_t max_vfs; /**< Maximum number of VFs. */ + uint16_t max_vmdq_pools; /**< Maximum number of VMDq pools. */ + uint32_t rx_offload_capa; /**< Device RX offload capabilities. */ + uint32_t tx_offload_capa; /**< Device TX offload capabilities. */ }; struct rte_eth_dev; @@ -694,6 +864,14 @@ typedef void (*eth_dev_infos_get_t)(struct rte_eth_dev *dev, struct rte_eth_dev_info *dev_info); /**< @internal Get specific informations of an Ethernet device. */ +typedef int (*eth_queue_start_t)(struct rte_eth_dev *dev, + uint16_t queue_id); +/**< @internal Start rx and tx of a queue of an Ethernet device. */ + +typedef int (*eth_queue_stop_t)(struct rte_eth_dev *dev, + uint16_t queue_id); +/**< @internal Stop rx and tx of a queue of an Ethernet device. */ + typedef int (*eth_rx_queue_setup_t)(struct rte_eth_dev *dev, uint16_t rx_queue_id, uint16_t nb_rx_desc, @@ -712,6 +890,13 @@ typedef int (*eth_tx_queue_setup_t)(struct rte_eth_dev *dev, typedef void (*eth_queue_release_t)(void *queue); /**< @internal Release memory resources allocated by given RX/TX queue. */ +typedef uint32_t (*eth_rx_queue_count_t)(struct rte_eth_dev *dev, + uint16_t rx_queue_id); +/**< @Get number of available descriptors on a receive queue of an Ethernet device. */ + +typedef int (*eth_rx_descriptor_done_t)(void *rxq, uint16_t offset); +/**< @Check DD bit of specific RX descriptor */ + typedef int (*vlan_filter_set_t)(struct rte_eth_dev *dev, uint16_t vlan_id, int on); @@ -782,6 +967,26 @@ typedef int (*flow_ctrl_set_t)(struct rte_eth_dev *dev, struct rte_eth_fc_conf *fc_conf); /**< @internal Setup flow control parameter on an Ethernet device */ +typedef int (*priority_flow_ctrl_set_t)(struct rte_eth_dev *dev, + struct rte_eth_pfc_conf *pfc_conf); +/**< @internal Setup priority flow control parameter on an Ethernet device */ + +typedef int (*reta_update_t)(struct rte_eth_dev *dev, + struct rte_eth_rss_reta *reta_conf); +/**< @internal Update RSS redirection table on an Ethernet device */ + +typedef int (*reta_query_t)(struct rte_eth_dev *dev, + struct rte_eth_rss_reta *reta_conf); +/**< @internal Query RSS redirection table on an Ethernet device */ + +typedef int (*rss_hash_update_t)(struct rte_eth_dev *dev, + struct rte_eth_rss_conf *rss_conf); +/**< @internal Update RSS hash configuration of an Ethernet device */ + +typedef int (*rss_hash_conf_get_t)(struct rte_eth_dev *dev, + struct rte_eth_rss_conf *rss_conf); +/**< @internal Get current RSS hash configuration of an Ethernet device */ + typedef int (*eth_dev_led_on_t)(struct rte_eth_dev *dev); /**< @internal Turn on SW controllable LED on an Ethernet device */ @@ -797,6 +1002,102 @@ typedef void (*eth_mac_addr_add_t)(struct rte_eth_dev *dev, uint32_t vmdq); /**< @internal Set a MAC address into Receive Address Address Register */ +typedef int (*eth_uc_hash_table_set_t)(struct rte_eth_dev *dev, + struct ether_addr *mac_addr, + uint8_t on); +/**< @internal Set a Unicast Hash bitmap */ + +typedef int (*eth_uc_all_hash_table_set_t)(struct rte_eth_dev *dev, + uint8_t on); +/**< @internal Set all Unicast Hash bitmap */ + +typedef int (*eth_set_vf_rx_mode_t)(struct rte_eth_dev *dev, + uint16_t vf, + uint16_t rx_mode, + uint8_t on); +/**< @internal Set a VF receive mode */ + +typedef int (*eth_set_vf_rx_t)(struct rte_eth_dev *dev, + uint16_t vf, + uint8_t on); +/**< @internal Set a VF receive mode */ + +typedef int (*eth_set_vf_tx_t)(struct rte_eth_dev *dev, + uint16_t vf, + uint8_t on); +/**< @internal Enable or disable a VF transmit */ + +typedef int (*eth_set_vf_vlan_filter_t)(struct rte_eth_dev *dev, + uint16_t vlan, + uint64_t vf_mask, + uint8_t vlan_on); +/**< @internal Set VF VLAN pool filter */ + +typedef int (*eth_mirror_rule_set_t)(struct rte_eth_dev *dev, + struct rte_eth_vmdq_mirror_conf *mirror_conf, + uint8_t rule_id, + uint8_t on); +/**< @internal Add a traffic mirroring rule on an Ethernet device */ + +typedef int (*eth_mirror_rule_reset_t)(struct rte_eth_dev *dev, + uint8_t rule_id); +/**< @internal Remove a traffic mirroring rule on an Ethernet device */ + +#ifdef RTE_NIC_BYPASS + +enum { + RTE_BYPASS_MODE_NONE, + RTE_BYPASS_MODE_NORMAL, + RTE_BYPASS_MODE_BYPASS, + RTE_BYPASS_MODE_ISOLATE, + RTE_BYPASS_MODE_NUM, +}; + +#define RTE_BYPASS_MODE_VALID(x) \ + ((x) > RTE_BYPASS_MODE_NONE && (x) < RTE_BYPASS_MODE_NUM) + +enum { + RTE_BYPASS_EVENT_NONE, + RTE_BYPASS_EVENT_START, + RTE_BYPASS_EVENT_OS_ON = RTE_BYPASS_EVENT_START, + RTE_BYPASS_EVENT_POWER_ON, + RTE_BYPASS_EVENT_OS_OFF, + RTE_BYPASS_EVENT_POWER_OFF, + RTE_BYPASS_EVENT_TIMEOUT, + RTE_BYPASS_EVENT_NUM +}; + +#define RTE_BYPASS_EVENT_VALID(x) \ + ((x) > RTE_BYPASS_EVENT_NONE && (x) < RTE_BYPASS_MODE_NUM) + +enum { + RTE_BYPASS_TMT_OFF, /* timeout disabled. */ + RTE_BYPASS_TMT_1_5_SEC, /* timeout for 1.5 seconds */ + RTE_BYPASS_TMT_2_SEC, /* timeout for 2 seconds */ + RTE_BYPASS_TMT_3_SEC, /* timeout for 3 seconds */ + RTE_BYPASS_TMT_4_SEC, /* timeout for 4 seconds */ + RTE_BYPASS_TMT_8_SEC, /* timeout for 8 seconds */ + RTE_BYPASS_TMT_16_SEC, /* timeout for 16 seconds */ + RTE_BYPASS_TMT_32_SEC, /* timeout for 32 seconds */ + RTE_BYPASS_TMT_NUM +}; + +#define RTE_BYPASS_TMT_VALID(x) \ + ((x) == RTE_BYPASS_TMT_OFF || \ + ((x) > RTE_BYPASS_TMT_OFF && (x) < RTE_BYPASS_TMT_NUM)) + +typedef void (*bypass_init_t)(struct rte_eth_dev *dev); +typedef int32_t (*bypass_state_set_t)(struct rte_eth_dev *dev, uint32_t *new_state); +typedef int32_t (*bypass_state_show_t)(struct rte_eth_dev *dev, uint32_t *state); +typedef int32_t (*bypass_event_set_t)(struct rte_eth_dev *dev, uint32_t state, uint32_t event); +typedef int32_t (*bypass_event_show_t)(struct rte_eth_dev *dev, uint32_t event_shift, uint32_t *event); +typedef int32_t (*bypass_wd_timeout_set_t)(struct rte_eth_dev *dev, uint32_t timeout); +typedef int32_t (*bypass_wd_timeout_show_t)(struct rte_eth_dev *dev, uint32_t *wd_timeout); +typedef int32_t (*bypass_ver_show_t)(struct rte_eth_dev *dev, uint32_t *ver); +typedef int32_t (*bypass_wd_reset_t)(struct rte_eth_dev *dev); +#endif + + /** * @internal A structure containing the functions exported by an Ethernet driver. */ @@ -819,15 +1120,30 @@ struct eth_dev_ops { vlan_tpid_set_t vlan_tpid_set; /**< Outer VLAN TPID Setup. */ vlan_strip_queue_set_t vlan_strip_queue_set; /**< VLAN Stripping on queue. */ vlan_offload_set_t vlan_offload_set; /**< Set VLAN Offload. */ + eth_queue_start_t rx_queue_start;/**< Start RX for a queue.*/ + eth_queue_stop_t rx_queue_stop;/**< Stop RX for a queue.*/ + eth_queue_start_t tx_queue_start;/**< Start TX for a queue.*/ + eth_queue_stop_t tx_queue_stop;/**< Stop TX for a queue.*/ eth_rx_queue_setup_t rx_queue_setup;/**< Set up device RX queue.*/ eth_queue_release_t rx_queue_release;/**< Release RX queue.*/ + eth_rx_queue_count_t rx_queue_count; /**< Get Rx queue count. */ + eth_rx_descriptor_done_t rx_descriptor_done; /**< Check rxd DD bit */ eth_tx_queue_setup_t tx_queue_setup;/**< Set up device TX queue.*/ eth_queue_release_t tx_queue_release;/**< Release TX queue.*/ eth_dev_led_on_t dev_led_on; /**< Turn on LED. */ eth_dev_led_off_t dev_led_off; /**< Turn off LED. */ flow_ctrl_set_t flow_ctrl_set; /**< Setup flow control. */ + priority_flow_ctrl_set_t priority_flow_ctrl_set; /**< Setup priority flow control.*/ eth_mac_addr_remove_t mac_addr_remove; /**< Remove MAC address */ eth_mac_addr_add_t mac_addr_add; /**< Add a MAC address */ + eth_uc_hash_table_set_t uc_hash_table_set; /**< Set Unicast Table Array */ + eth_uc_all_hash_table_set_t uc_all_hash_table_set; /**< Set Unicast hash bitmap */ + eth_mirror_rule_set_t mirror_rule_set; /**< Add a traffic mirror rule.*/ + eth_mirror_rule_reset_t mirror_rule_reset; /**< reset a traffic mirror rule.*/ + eth_set_vf_rx_mode_t set_vf_rx_mode; /**< Set VF RX mode */ + eth_set_vf_rx_t set_vf_rx; /**< enable/disable a VF receive */ + eth_set_vf_tx_t set_vf_tx; /**< enable/disable a VF transmit */ + eth_set_vf_vlan_filter_t set_vf_vlan_filter; /**< Set VF VLAN filter */ /** Add a signature filter. */ fdir_add_signature_filter_t fdir_add_signature_filter; @@ -845,6 +1161,27 @@ struct eth_dev_ops { fdir_remove_perfect_filter_t fdir_remove_perfect_filter; /** Setup masks for FDIR filtering. */ fdir_set_masks_t fdir_set_masks; + /** Update redirection table. */ + reta_update_t reta_update; + /** Query redirection table. */ + reta_query_t reta_query; + /* bypass control */ +#ifdef RTE_NIC_BYPASS + bypass_init_t bypass_init; + bypass_state_set_t bypass_state_set; + bypass_state_show_t bypass_state_show; + bypass_event_set_t bypass_event_set; + bypass_event_show_t bypass_event_show; + bypass_wd_timeout_set_t bypass_wd_timeout_set; + bypass_wd_timeout_show_t bypass_wd_timeout_show; + bypass_ver_show_t bypass_ver_show; + bypass_wd_reset_t bypass_wd_reset; +#endif + + /** Configure RSS hash protocols. */ + rss_hash_update_t rss_hash_update; + /** Get current RSS hash configuration. */ + rss_hash_conf_get_t rss_hash_conf_get; }; /** @@ -867,6 +1204,14 @@ struct rte_eth_dev { struct rte_eth_dev_cb_list callbacks; /**< User application callbacks */ }; +struct rte_eth_dev_sriov { + uint8_t active; /**< SRIOV is active with 16, 32 or 64 pools */ + uint8_t nb_q_per_pool; /**< rx queue number per pool */ + uint16_t def_vmdq_idx; /**< Default pool num used for PF */ + uint16_t def_pool_q_idx; /**< Default pool queue start reg index */ +}; +#define RTE_ETH_DEV_SRIOV(dev) ((dev)->data->sriov) + /** * @internal * The data part, with no function pointers, associated with each ethernet device. @@ -880,6 +1225,8 @@ struct rte_eth_dev_data { uint16_t nb_rx_queues; /**< Number of RX queues. */ uint16_t nb_tx_queues; /**< Number of TX queues. */ + struct rte_eth_dev_sriov sriov; /**< SRIOV data */ + void *dev_private; /**< PMD-specific private data */ struct rte_eth_link dev_link; @@ -890,6 +1237,10 @@ struct rte_eth_dev_data { uint64_t rx_mbuf_alloc_failed; /**< RX ring mbuf allocation failures. */ struct ether_addr* mac_addrs;/**< Device Ethernet Link address. */ + uint64_t mac_pool_sel[ETH_NUM_RECEIVE_MAC_ADDR]; + /** bitmap array of associating Ethernet MAC addresses to pools */ + struct ether_addr* hash_mac_addrs; + /** Device Ethernet MAC addresses of hash filtering. */ uint8_t port_id; /**< Device [external] port identifier. */ uint8_t promiscuous : 1, /**< RX promiscuous mode ON(1) / OFF(0). */ scattered_rx : 1, /**< RX of scattered packets is ON(1) / OFF(0) */ @@ -915,6 +1266,17 @@ extern struct rte_eth_dev rte_eth_devices[]; */ extern uint8_t rte_eth_dev_count(void); +/** + * Function for internal use by dummy drivers primarily, e.g. ring-based + * driver. + * Allocates a new ethdev slot for an ethernet device and returns the pointer + * to that slot for the driver to use. + * + * @return + * - Slot in the rte_dev_devices array for a new device; + */ +struct rte_eth_dev *rte_eth_dev_allocate(void); + struct eth_driver; /** * @internal @@ -982,105 +1344,6 @@ struct eth_driver { */ extern void rte_eth_driver_register(struct eth_driver *eth_drv); -/** - * The initialization function of the driver for - * Intel(r) IGB Gigabit Ethernet Controller devices. - * This function is invoked once at EAL start time. - * @return - * 0 on success - */ -extern int rte_igb_pmd_init(void); - -/** - * The initialization function of the driver for - * Intel(r) EM Gigabit Ethernet Controller devices. - * This function is invoked once at EAL start time. - * @return - * 0 on success - */ -extern int rte_em_pmd_init(void); - -/** - * The initialization function of the driver for 1Gbps Intel IGB_VF - * Ethernet devices. - * Invoked once at EAL start time. - * @return - * 0 on success - */ -extern int rte_igbvf_pmd_init(void); - -/** - * The initialization function of the driver for 10Gbps Intel IXGBE - * Ethernet devices. - * Invoked once at EAL start time. - * @return - * 0 on success - */ -extern int rte_ixgbe_pmd_init(void); - -/** - * The initialization function of the driver for 10Gbps Intel IXGBE_VF - * Ethernet devices. - * Invoked once at EAL start time. - * @return - * 0 on success - */ -extern int rte_ixgbevf_pmd_init(void); - -/** - * The initialization function of *all* supported and enabled drivers. - * Right now, the following PMDs are supported: - * - igb - * - igbvf - * - em - * - ixgbe - * - ixgbevf - * This function is invoked once at EAL start time. - * @return - * 0 on success. - * Error code of the device initialization failure, - * -ENODEV if there are no drivers available - * (e.g. if all driver config options are = n). - */ -static inline -int rte_pmd_init_all(void) -{ - int ret = -ENODEV; - -#ifdef RTE_LIBRTE_IGB_PMD - if ((ret = rte_igb_pmd_init()) != 0) { - RTE_LOG(ERR, PMD, "Cannot init igb PMD\n"); - return (ret); - } - if ((ret = rte_igbvf_pmd_init()) != 0) { - RTE_LOG(ERR, PMD, "Cannot init igbvf PMD\n"); - return (ret); - } -#endif /* RTE_LIBRTE_IGB_PMD */ - -#ifdef RTE_LIBRTE_EM_PMD - if ((ret = rte_em_pmd_init()) != 0) { - RTE_LOG(ERR, PMD, "Cannot init em PMD\n"); - return (ret); - } -#endif /* RTE_LIBRTE_EM_PMD */ - -#ifdef RTE_LIBRTE_IXGBE_PMD - if ((ret = rte_ixgbe_pmd_init()) != 0) { - RTE_LOG(ERR, PMD, "Cannot init ixgbe PMD\n"); - return (ret); - } - if ((ret = rte_ixgbevf_pmd_init()) != 0) { - RTE_LOG(ERR, PMD, "Cannot init ixgbevf PMD\n"); - return (ret); - } -#endif /* RTE_LIBRTE_IXGBE_PMD */ - - if (ret == -ENODEV) - RTE_LOG(ERR, PMD, "No PMD(s) are configured\n"); - return (ret); -} - /** * Configure an Ethernet device. * This function must be invoked first before any other function in the @@ -1202,6 +1465,84 @@ extern int rte_eth_tx_queue_setup(uint8_t port_id, uint16_t tx_queue_id, uint16_t nb_tx_desc, unsigned int socket_id, const struct rte_eth_txconf *tx_conf); +/* + * Return the NUMA socket to which an Ethernet device is connected + * + * @param port_id + * The port identifier of the Ethernet device + * @return + * The NUMA socket id to which the Ethernet device is connected or + * a default of zero if the socket could not be determined. + * -1 is returned is the port_id value is out of range. + */ +extern int rte_eth_dev_socket_id(uint8_t port_id); + +/* + * Start specified RX queue of a port + * + * @param port_id + * The port identifier of the Ethernet device + * @param rx_queue_id + * The index of the rx queue to update the ring. + * The value must be in the range [0, nb_rx_queue - 1] previously supplied + * to rte_eth_dev_configure(). + * @return + * - 0: Success, the transmit queue is correctly set up. + * - -EINVAL: The port_id or the queue_id out of range. + * - -ENOTSUP: The function not supported in PMD driver. + */ +extern int rte_eth_dev_rx_queue_start(uint8_t port_id, uint16_t rx_queue_id); + +/* + * Stop specified RX queue of a port + * + * @param port_id + * The port identifier of the Ethernet device + * @param rx_queue_id + * The index of the rx queue to update the ring. + * The value must be in the range [0, nb_rx_queue - 1] previously supplied + * to rte_eth_dev_configure(). + * @return + * - 0: Success, the transmit queue is correctly set up. + * - -EINVAL: The port_id or the queue_id out of range. + * - -ENOTSUP: The function not supported in PMD driver. + */ +extern int rte_eth_dev_rx_queue_stop(uint8_t port_id, uint16_t rx_queue_id); + +/* + * Start specified TX queue of a port + * + * @param port_id + * The port identifier of the Ethernet device + * @param tx_queue_id + * The index of the tx queue to update the ring. + * The value must be in the range [0, nb_tx_queue - 1] previously supplied + * to rte_eth_dev_configure(). + * @return + * - 0: Success, the transmit queue is correctly set up. + * - -EINVAL: The port_id or the queue_id out of range. + * - -ENOTSUP: The function not supported in PMD driver. + */ +extern int rte_eth_dev_tx_queue_start(uint8_t port_id, uint16_t tx_queue_id); + +/* + * Stop specified TX queue of a port + * + * @param port_id + * The port identifier of the Ethernet device + * @param tx_queue_id + * The index of the tx queue to update the ring. + * The value must be in the range [0, nb_tx_queue - 1] previously supplied + * to rte_eth_dev_configure(). + * @return + * - 0: Success, the transmit queue is correctly set up. + * - -EINVAL: The port_id or the queue_id out of range. + * - -ENOTSUP: The function not supported in PMD driver. + */ +extern int rte_eth_dev_tx_queue_stop(uint8_t port_id, uint16_t tx_queue_id); + + + /** * Start an Ethernet device. * @@ -1600,6 +1941,59 @@ rte_eth_rx_burst(uint8_t port_id, uint16_t queue_id, } #endif +/** + * Get the number of used descriptors in a specific queue + * + * @param port_id + * The port identifier of the Ethernet device. + * @param queue_id + * The queue id on the specific port. + * @return + * The number of used descriptors in the specific queue. + */ +#ifdef RTE_LIBRTE_ETHDEV_DEBUG +extern uint32_t rte_eth_rx_queue_count(uint8_t port_id, uint16_t queue_id); +#else +static inline uint32_t +rte_eth_rx_queue_count(uint8_t port_id, uint16_t queue_id) +{ + struct rte_eth_dev *dev; + + dev = &rte_eth_devices[port_id]; + return (*dev->dev_ops->rx_queue_count)(dev, queue_id); +} +#endif + +/** + * Check if the DD bit of the specific RX descriptor in the queue has been set + * + * @param port_id + * The port identifier of the Ethernet device. + * @param queue_id + * The queue id on the specific port. + * @offset + * The offset of the descriptor ID from tail. + * @return + * - (1) if the specific DD bit is set. + * - (0) if the specific DD bit is not set. + * - (-ENODEV) if *port_id* invalid. + */ +#ifdef RTE_LIBRTE_ETHDEV_DEBUG +extern int rte_eth_rx_descriptor_done(uint8_t port_id, + uint16_t queue_id, + uint16_t offset); +#else +static inline int +rte_eth_rx_descriptor_done(uint8_t port_id, uint16_t queue_id, uint16_t offset) +{ + struct rte_eth_dev *dev; + + dev = &rte_eth_devices[port_id]; + return (*dev->dev_ops->rx_descriptor_done)( \ + dev->data->rx_queues[queue_id], offset); +} +#endif + /** * Send a burst of output packets on a transmit queue of an Ethernet device. * @@ -2007,6 +2401,24 @@ int rte_eth_led_off(uint8_t port_id); int rte_eth_dev_flow_ctrl_set(uint8_t port_id, struct rte_eth_fc_conf *fc_conf); +/** + * Configure the Ethernet priority flow control under DCB environment + * for Ethernet device. + * + * @param port_id + * The port identifier of the Ethernet device. + * @param pfc_conf + * The pointer to the structure of the priority flow control parameters. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support priority flow control mode. + * - (-ENODEV) if *port_id* invalid. + * - (-EINVAL) if bad parameter + * - (-EIO) if flow control setup failure + */ +int rte_eth_dev_priority_flow_ctrl_set(uint8_t port_id, + struct rte_eth_pfc_conf *pfc_conf); + /** * Add a MAC address to an internal array of addresses used to enable whitelist * filtering to accept packets only if the destination MAC address matches. @@ -2043,6 +2455,402 @@ int rte_eth_dev_mac_addr_add(uint8_t port, struct ether_addr *mac_addr, */ int rte_eth_dev_mac_addr_remove(uint8_t port, struct ether_addr *mac_addr); +/** + * Update Redirection Table(RETA) of Receive Side Scaling of Ethernet device. + * + * @param port + * The port identifier of the Ethernet device. + * @param reta_conf + * RETA to update. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_rss_reta_update(uint8_t port, + struct rte_eth_rss_reta *reta_conf); + + /** + * Query Redirection Table(RETA) of Receive Side Scaling of Ethernet device. + * + * @param port + * The port identifier of the Ethernet device. + * @param reta_conf + * RETA to query. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_rss_reta_query(uint8_t port, + struct rte_eth_rss_reta *reta_conf); + + /** + * Updates unicast hash table for receiving packet with the given destination + * MAC address, and the packet is routed to all VFs for which the RX mode is + * accept packets that match the unicast hash table. + * + * @param port + * The port identifier of the Ethernet device. + * @param addr + * Unicast MAC address. + * @param on + * 1 - Set an unicast hash bit for receiving packets with the MAC address. + * 0 - Clear an unicast hash bit. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-ENODEV) if *port_id* invalid. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_uc_hash_table_set(uint8_t port,struct ether_addr *addr, + uint8_t on); + + /** + * Updates all unicast hash bitmaps for receiving packet with any Unicast + * Ethernet MAC addresses,the packet is routed to all VFs for which the RX + * mode is accept packets that match the unicast hash table. + * + * @param port + * The port identifier of the Ethernet device. + * @param on + * 1 - Set all unicast hash bitmaps for receiving all the Ethernet + * MAC addresses + * 0 - Clear all unicast hash bitmaps + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-ENODEV) if *port_id* invalid. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_uc_all_hash_table_set(uint8_t port,uint8_t on); + + /** + * Set RX L2 Filtering mode of a VF of an Ethernet device. + * + * @param port + * The port identifier of the Ethernet device. + * @param vf + * VF id. + * @param rx_mode + * The RX mode mask, which is one or more of accepting Untagged Packets, + * packets that match the PFUTA table, Broadcast and Multicast Promiscuous. + * ETH_VMDQ_ACCEPT_UNTAG,ETH_VMDQ_ACCEPT_HASH_UC, + * ETH_VMDQ_ACCEPT_BROADCAST and ETH_VMDQ_ACCEPT_MULTICAST will be used + * in rx_mode. + * @param on + * 1 - Enable a VF RX mode. + * 0 - Disable a VF RX mode. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_set_vf_rxmode(uint8_t port, uint16_t vf, uint16_t rx_mode, + uint8_t on); + +/** +* Enable or disable a VF traffic transmit of the Ethernet device. +* +* @param port +* The port identifier of the Ethernet device. +* @param vf +* VF id. +* @param on +* 1 - Enable a VF traffic transmit. +* 0 - Disable a VF traffic transmit. +* @return +* - (0) if successful. +* - (-ENODEV) if *port_id* invalid. +* - (-ENOTSUP) if hardware doesn't support. +* - (-EINVAL) if bad parameter. +*/ +int +rte_eth_dev_set_vf_tx(uint8_t port,uint16_t vf, uint8_t on); + +/** +* Enable or disable a VF traffic receive of an Ethernet device. +* +* @param port +* The port identifier of the Ethernet device. +* @param vf +* VF id. +* @param on +* 1 - Enable a VF traffic receive. +* 0 - Disable a VF traffic receive. +* @return +* - (0) if successful. +* - (-ENOTSUP) if hardware doesn't support. +* - (-ENODEV) if *port_id* invalid. +* - (-EINVAL) if bad parameter. +*/ +int +rte_eth_dev_set_vf_rx(uint8_t port,uint16_t vf, uint8_t on); + +/** +* Enable/Disable hardware VF VLAN filtering by an Ethernet device of +* received VLAN packets tagged with a given VLAN Tag Identifier. +* +* @param port id +* The port identifier of the Ethernet device. +* @param vlan_id +* The VLAN Tag Identifier whose filtering must be enabled or disabled. +* @param vf_mask +* Bitmap listing which VFs participate in the VLAN filtering. +* @param vlan_on +* 1 - Enable VFs VLAN filtering. +* 0 - Disable VFs VLAN filtering. +* @return +* - (0) if successful. +* - (-ENOTSUP) if hardware doesn't support. +* - (-ENODEV) if *port_id* invalid. +* - (-EINVAL) if bad parameter. +*/ +int +rte_eth_dev_set_vf_vlan_filter(uint8_t port, uint16_t vlan_id, + uint64_t vf_mask, + uint8_t vlan_on); + +/** + * Set a traffic mirroring rule on an Ethernet device + * + * @param port_id + * The port identifier of the Ethernet device. + * @param mirror_conf + * The pointer to the traffic mirroring structure describing the mirroring rule. + * The *rte_eth_vm_mirror_conf* structure includes the type of mirroring rule, + * destination pool and the value of rule if enable vlan or pool mirroring. + * + * @param rule_id + * The index of traffic mirroring rule, we support four separated rules. + * @param on + * 1 - Enable a mirroring rule. + * 0 - Disable a mirroring rule. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support this feature. + * - (-ENODEV) if *port_id* invalid. + * - (-EINVAL) if the mr_conf information is not correct. + */ +int rte_eth_mirror_rule_set(uint8_t port_id, + struct rte_eth_vmdq_mirror_conf *mirror_conf, + uint8_t rule_id, + uint8_t on); + +/** + * Reset a traffic mirroring rule on an Ethernet device. + * + * @param port_id + * The port identifier of the Ethernet device. + * @param rule_id + * The index of traffic mirroring rule, we support four separated rules. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support this feature. + * - (-ENODEV) if *port_id* invalid. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_mirror_rule_reset(uint8_t port_id, + uint8_t rule_id); + +/** + * Initialize bypass logic. This function needs to be called before + * executing any other bypass API. + * + * @param port + * The port identifier of the Ethernet device. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_init(uint8_t port); + +/** + * Return bypass state. + * + * @param port + * The port identifier of the Ethernet device. + * @param state + * The return bypass state. + * - (1) Normal mode + * - (2) Bypass mode + * - (3) Isolate mode + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_state_show(uint8_t port, uint32_t *state); + +/** + * Set bypass state + * + * @param port + * The port identifier of the Ethernet device. + * @param state + * The current bypass state. + * - (1) Normal mode + * - (2) Bypass mode + * - (3) Isolate mode + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_state_set(uint8_t port, uint32_t *new_state); + +/** + * Return bypass state when given event occurs. + * + * @param port + * The port identifier of the Ethernet device. + * @param event + * The bypass event + * - (1) Main power on (power button is pushed) + * - (2) Auxiliary power on (power supply is being plugged) + * - (3) Main power off (system shutdown and power supply is left plugged in) + * - (4) Auxiliary power off (power supply is being unplugged) + * - (5) Display or set the watchdog timer + * @param state + * The bypass state when given event occurred. + * - (1) Normal mode + * - (2) Bypass mode + * - (3) Isolate mode + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_event_show(uint8_t port, uint32_t event, uint32_t *state); + +/** + * Set bypass state when given event occurs. + * + * @param port + * The port identifier of the Ethernet device. + * @param event + * The bypass event + * - (1) Main power on (power button is pushed) + * - (2) Auxiliary power on (power supply is being plugged) + * - (3) Main power off (system shutdown and power supply is left plugged in) + * - (4) Auxiliary power off (power supply is being unplugged) + * - (5) Display or set the watchdog timer + * @param state + * The assigned state when given event occurs. + * - (1) Normal mode + * - (2) Bypass mode + * - (3) Isolate mode + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_event_store(uint8_t port, uint32_t event, uint32_t state); + +/** + * Set bypass watchdog timeout count. + * + * @param port + * The port identifier of the Ethernet device. + * @param state + * The timeout to be set. + * - (0) 0 seconds (timer is off) + * - (1) 1.5 seconds + * - (2) 2 seconds + * - (3) 3 seconds + * - (4) 4 seconds + * - (5) 8 seconds + * - (6) 16 seconds + * - (7) 32 seconds + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_wd_timeout_store(uint8_t port, uint32_t timeout); + +/** + * Get bypass firmware version. + * + * @param port + * The port identifier of the Ethernet device. + * @param ver + * The firmware version + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_ver_show(uint8_t port, uint32_t *ver); + +/** + * Return bypass watchdog timeout in seconds + * + * @param port + * The port identifier of the Ethernet device. + * @param wd_timeout + * The return watchdog timeout. "0" represents timer expired + * - (0) 0 seconds (timer is off) + * - (1) 1.5 seconds + * - (2) 2 seconds + * - (3) 3 seconds + * - (4) 4 seconds + * - (5) 8 seconds + * - (6) 16 seconds + * - (7) 32 seconds + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_wd_timeout_show(uint8_t port, uint32_t *wd_timeout); + +/** + * Reset bypass watchdog timer + * + * @param port + * The port identifier of the Ethernet device. + * @return + * - (0) if successful. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_bypass_wd_reset(uint8_t port); + + /** + * Configuration of Receive Side Scaling hash computation of Ethernet device. + * + * @param port + * The port identifier of the Ethernet device. + * @param rss_conf + * The new configuration to use for RSS hash computation on the port. + * @return + * - (0) if successful. + * - (-ENODEV) if port identifier is invalid. + * - (-ENOTSUP) if hardware doesn't support. + * - (-EINVAL) if bad parameter. + */ +int rte_eth_dev_rss_hash_update(uint8_t port_id, + struct rte_eth_rss_conf *rss_conf); + + /** + * Retrieve current configuration of Receive Side Scaling hash computation + * of Ethernet device. + * + * @param port + * The port identifier of the Ethernet device. + * @param rss_conf + * Where to store the current RSS hash configuration of the Ethernet device. + * @return + * - (0) if successful. + * - (-ENODEV) if port identifier is invalid. + * - (-ENOTSUP) if hardware doesn't support RSS. + */ +int +rte_eth_dev_rss_hash_conf_get(uint8_t port_id, + struct rte_eth_rss_conf *rss_conf); #ifdef __cplusplus }