FFC/FPC-to-Board 0.50mm (.020") SMT Top Contact Right Angle, ZIF, Style Receptacle 52745 / 52435 Source: http://www.molex.com/product/ffc/52745.html >NAME >VALUE >NAME >VALUE >NAME FFC/FPC-to-Board 0.50mm (.020") SMT Top Contact Right Angle, ZIF, Style Receptacle 52745 / 52435 Source: http://www.molex.com/product/ffc/52745.html >VALUE SUPPLY SYMBOL >DRAWING_NAME >LAST_DATE_TIME >SHEET Sheet: FRAME DIN A3, landscape with location and doc. field PIN HEADER >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE >VALUE >NAME >VALUE >NAME >VALUE >NAME PIN HEADER >NAME >VALUE >NAME >VALUE >NAME >VALUE 2mm SMD side-entry connector. tDocu layer indicates the actual physical plastic housing. +/- indicate SparkFun standard batteries and wiring. >Name >Value + - >Name >Value >NAME >VALUE >NAME >VALUE This footprint was designed to help hold the alignment of a through-hole component (i.e. 6-pin header) while soldering it into place. You may notice that each hole has been shifted either up or down by 0.005 of an inch from it's more standard position (which is a perfectly straight line). This slight alteration caused the pins (the squares in the middle) to touch the edges of the holes. Because they are alternating, it causes a "brace" to hold the component in place. 0.005 has proven to be the perfect amount of "off-center" position when using our standard breakaway headers. Although looks a little odd when you look at the bare footprint, once you have a header in there, the alteration is very hard to notice. Also, if you push a header all the way into place, it is covered up entirely on the bottom side. This idea of altering the position of holes to aid alignment will be further integrated into the Sparkfun Library for other footprints. It can help hold any component with 3 or more connection pins. >NAME >VALUE >NAME >VALUE >NAME >VALUE >Name >Value + - >NAME >VALUE >Name >Value + - <H3>JST-2-PTH-KIT</h3> 2-Pin JST, through-hole connector Warning: This is the KIT version of this package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >Name >Value + - >NAME >VALUE >Name >Value RESISTOR chip >NAME >VALUE >NAME >VALUE >NAME >VALUE CAPACITOR chip >NAME >VALUE 1/6W Thru-hole Resistor - *UNPROVEN* >NAME >VALUE >NAME >VALUE 1/4W Resistor, 0.4" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1/2W Resistor, 0.5" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1W Resistor, 0.6" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 2W Resistor, 0.8" wide Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value <h3>AXIAL-0.3-KIT</h3> Commonly used for 1/4W through-hole resistors. 0.3" pitch between holes. Warning: This is the KIT version of the AXIAL-0.3 package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >Name >Value LED 5 mm, round >NAME >VALUE LED 3 mm, round >NAME >VALUE >NAME >VALUE >NAME >VALUE L S >NAME >VALUE <h3>LED 3MM - No Silk</h3> 3 mm, round >NAME >VALUE <h3>LED5MM-KIT</h3> 5MM Through-hole LED Warning: This is the KIT version of this package. This package has a smaller diameter top stop mask, which doesn't cover the diameter of the pad. This means only the bottom side of the pads' copper will be exposed. You'll only be able to solder to the bottom side. >NAME >VALUE >NAME >VALUE MOSI RESET SCK MISO +5 GND GND GND GND >NAME >VALUE MOSI RESET SCK MISO +5 GND >VALUE >NAME >NAME >VALUE >VALUE >NAME >NAME >VALUE >NAME >VALUE AVR ICSP Header This is the standard AVR In Circuit Serial Programming header. Minimal, but includes pin one indicator. Works with standard Olimex programmers. Also look for the 6-pin reduced version. Spark Fun Electronics SKU: PRT-00778 AVR ISP 6 Pin This is the reduced ISP connector for AVR programming. Common on Arduino. This footprint will take up less PCB space and can be used with a 10-pin to 6-pin adapter such as SKU: BOB-08508 Header 5x2 Standard 10-pin dual row 0.1" header. Commonly used with AVR-ISP. Use with Spark Fun Electronics SKU: PRT-00778 PIN HEADER Header 2 Standard 2-pin 0.1" header. Use with straight break away headers (SKU : PRT-00116), right angle break away headers (PRT-00553), swiss pins (PRT-00743), machine pins (PRT-00117), and female headers (PRT-00115). Molex polarized connector foot print use with SKU : PRT-08233 with associated crimp pins and housings. Resistor Basic schematic elements and footprints for 0603, 1206, and PTH resistors. LEDs Standard schematic elements and footprints for 5mm, 3mm, 1206, and 0603 sized LEDs. 5mm - Spark Fun Electronics SKU : COM-00529 (and others) VCC is 3.3V or 5V supply comes from target board or programmer JTAG FTDI The connector must be reversed compared to mainboard