+ * @param reta_size
+ * Redirection table size. The table size can be queried by
+ * rte_eth_dev_info_get().
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_rss_reta_query(uint8_t port,
+ struct rte_eth_rss_reta_entry64 *reta_conf,
+ uint16_t reta_size);
+
+ /**
+ * Updates unicast hash table for receiving packet with the given destination
+ * MAC address, and the packet is routed to all VFs for which the RX mode is
+ * accept packets that match the unicast hash table.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param addr
+ * Unicast MAC address.
+ * @param on
+ * 1 - Set an unicast hash bit for receiving packets with the MAC address.
+ * 0 - Clear an unicast hash bit.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_uc_hash_table_set(uint8_t port,struct ether_addr *addr,
+ uint8_t on);
+
+ /**
+ * Updates all unicast hash bitmaps for receiving packet with any Unicast
+ * Ethernet MAC addresses,the packet is routed to all VFs for which the RX
+ * mode is accept packets that match the unicast hash table.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param on
+ * 1 - Set all unicast hash bitmaps for receiving all the Ethernet
+ * MAC addresses
+ * 0 - Clear all unicast hash bitmaps
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_uc_all_hash_table_set(uint8_t port,uint8_t on);
+
+ /**
+ * Set RX L2 Filtering mode of a VF of an Ethernet device.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param vf
+ * VF id.
+ * @param rx_mode
+ * The RX mode mask, which is one or more of accepting Untagged Packets,
+ * packets that match the PFUTA table, Broadcast and Multicast Promiscuous.
+ * ETH_VMDQ_ACCEPT_UNTAG,ETH_VMDQ_ACCEPT_HASH_UC,
+ * ETH_VMDQ_ACCEPT_BROADCAST and ETH_VMDQ_ACCEPT_MULTICAST will be used
+ * in rx_mode.
+ * @param on
+ * 1 - Enable a VF RX mode.
+ * 0 - Disable a VF RX mode.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_set_vf_rxmode(uint8_t port, uint16_t vf, uint16_t rx_mode,
+ uint8_t on);
+
+/**
+* Enable or disable a VF traffic transmit of the Ethernet device.
+*
+* @param port
+* The port identifier of the Ethernet device.
+* @param vf
+* VF id.
+* @param on
+* 1 - Enable a VF traffic transmit.
+* 0 - Disable a VF traffic transmit.
+* @return
+* - (0) if successful.
+* - (-ENODEV) if *port_id* invalid.
+* - (-ENOTSUP) if hardware doesn't support.
+* - (-EINVAL) if bad parameter.
+*/
+int
+rte_eth_dev_set_vf_tx(uint8_t port,uint16_t vf, uint8_t on);
+
+/**
+* Enable or disable a VF traffic receive of an Ethernet device.
+*
+* @param port
+* The port identifier of the Ethernet device.
+* @param vf
+* VF id.
+* @param on
+* 1 - Enable a VF traffic receive.
+* 0 - Disable a VF traffic receive.
+* @return
+* - (0) if successful.
+* - (-ENOTSUP) if hardware doesn't support.
+* - (-ENODEV) if *port_id* invalid.
+* - (-EINVAL) if bad parameter.
+*/
+int
+rte_eth_dev_set_vf_rx(uint8_t port,uint16_t vf, uint8_t on);
+
+/**
+* Enable/Disable hardware VF VLAN filtering by an Ethernet device of
+* received VLAN packets tagged with a given VLAN Tag Identifier.
+*
+* @param port id
+* The port identifier of the Ethernet device.
+* @param vlan_id
+* The VLAN Tag Identifier whose filtering must be enabled or disabled.
+* @param vf_mask
+* Bitmap listing which VFs participate in the VLAN filtering.
+* @param vlan_on
+* 1 - Enable VFs VLAN filtering.
+* 0 - Disable VFs VLAN filtering.
+* @return
+* - (0) if successful.
+* - (-ENOTSUP) if hardware doesn't support.
+* - (-ENODEV) if *port_id* invalid.
+* - (-EINVAL) if bad parameter.
+*/
+int
+rte_eth_dev_set_vf_vlan_filter(uint8_t port, uint16_t vlan_id,
+ uint64_t vf_mask,
+ uint8_t vlan_on);
+
+/**
+ * Set a traffic mirroring rule on an Ethernet device
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param mirror_conf
+ * The pointer to the traffic mirroring structure describing the mirroring rule.
+ * The *rte_eth_vm_mirror_conf* structure includes the type of mirroring rule,
+ * destination pool and the value of rule if enable vlan or pool mirroring.
+ *
+ * @param rule_id
+ * The index of traffic mirroring rule, we support four separated rules.
+ * @param on
+ * 1 - Enable a mirroring rule.
+ * 0 - Disable a mirroring rule.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the mr_conf information is not correct.
+ */
+int rte_eth_mirror_rule_set(uint8_t port_id,
+ struct rte_eth_mirror_conf *mirror_conf,
+ uint8_t rule_id,
+ uint8_t on);
+
+/**
+ * Reset a traffic mirroring rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param rule_id
+ * The index of traffic mirroring rule, we support four separated rules.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_mirror_rule_reset(uint8_t port_id,
+ uint8_t rule_id);
+
+/**
+ * Set the rate limitation for a queue on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_idx
+ * The queue id.
+ * @param tx_rate
+ * The tx rate allocated from the total link speed for this queue.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_set_queue_rate_limit(uint8_t port_id, uint16_t queue_idx,
+ uint16_t tx_rate);
+
+/**
+ * Set the rate limitation for a vf on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param vf
+ * VF id.
+ * @param tx_rate
+ * The tx rate allocated from the total link speed for this VF id.
+ * @param q_msk
+ * The queue mask which need to set the rate.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_set_vf_rate_limit(uint8_t port_id, uint16_t vf,
+ uint16_t tx_rate, uint64_t q_msk);
+
+/**
+ * Initialize bypass logic. This function needs to be called before
+ * executing any other bypass API.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_init(uint8_t port);
+
+/**
+ * Return bypass state.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param state
+ * The return bypass state.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_state_show(uint8_t port, uint32_t *state);
+
+/**
+ * Set bypass state
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param new_state
+ * The current bypass state.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_state_set(uint8_t port, uint32_t *new_state);
+
+/**
+ * Return bypass state when given event occurs.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param event
+ * The bypass event
+ * - (1) Main power on (power button is pushed)
+ * - (2) Auxiliary power on (power supply is being plugged)
+ * - (3) Main power off (system shutdown and power supply is left plugged in)
+ * - (4) Auxiliary power off (power supply is being unplugged)
+ * - (5) Display or set the watchdog timer
+ * @param state
+ * The bypass state when given event occurred.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_event_show(uint8_t port, uint32_t event, uint32_t *state);
+
+/**
+ * Set bypass state when given event occurs.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param event
+ * The bypass event
+ * - (1) Main power on (power button is pushed)
+ * - (2) Auxiliary power on (power supply is being plugged)
+ * - (3) Main power off (system shutdown and power supply is left plugged in)
+ * - (4) Auxiliary power off (power supply is being unplugged)
+ * - (5) Display or set the watchdog timer
+ * @param state
+ * The assigned state when given event occurs.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_event_store(uint8_t port, uint32_t event, uint32_t state);
+
+/**
+ * Set bypass watchdog timeout count.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param timeout
+ * The timeout to be set.
+ * - (0) 0 seconds (timer is off)
+ * - (1) 1.5 seconds
+ * - (2) 2 seconds
+ * - (3) 3 seconds
+ * - (4) 4 seconds
+ * - (5) 8 seconds
+ * - (6) 16 seconds
+ * - (7) 32 seconds
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_wd_timeout_store(uint8_t port, uint32_t timeout);
+
+/**
+ * Get bypass firmware version.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param ver
+ * The firmware version
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_ver_show(uint8_t port, uint32_t *ver);
+
+/**
+ * Return bypass watchdog timeout in seconds
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param wd_timeout
+ * The return watchdog timeout. "0" represents timer expired
+ * - (0) 0 seconds (timer is off)
+ * - (1) 1.5 seconds
+ * - (2) 2 seconds
+ * - (3) 3 seconds
+ * - (4) 4 seconds
+ * - (5) 8 seconds
+ * - (6) 16 seconds
+ * - (7) 32 seconds