#include <rte_memory.h>
#include <rte_memcpy.h>
#include <rte_memzone.h>
-#include <rte_tailq.h>
#include <rte_eal.h>
#include <rte_per_lcore.h>
#include <rte_launch.h>
static struct kni_port_params *kni_port_params_array[RTE_MAX_ETHPORTS];
-/* RX and TX Prefetch, Host, and Write-back threshold values should be
- * carefully set for optimal performance. Consult the network
- * controller's datasheet and supporting DPDK documentation for guidance
- * on how these parameters should be set.
- */
-/* RX ring configuration */
-static const struct rte_eth_rxconf rx_conf = {
- .rx_thresh = {
- .pthresh = 8, /* Ring prefetch threshold */
- .hthresh = 8, /* Ring host threshold */
- .wthresh = 4, /* Ring writeback threshold */
- },
- .rx_free_thresh = 0, /* Immediately free RX descriptors */
-};
-
-/*
- * These default values are optimized for use with the Intel(R) 82599 10 GbE
- * Controller and the DPDK ixgbe PMD. Consider using other values for other
- * network controllers and/or network drivers.
- */
-/* TX ring configuration */
-static const struct rte_eth_txconf tx_conf = {
- .tx_thresh = {
- .pthresh = 36, /* Ring prefetch threshold */
- .hthresh = 0, /* Ring host threshold */
- .wthresh = 0, /* Ring writeback threshold */
- },
- .tx_free_thresh = 0, /* Use PMD default values */
- .tx_rs_thresh = 0, /* Use PMD default values */
-};
/* Options for configuring ethernet port */
static struct rte_eth_conf port_conf = {
goto fail;
}
kni_port_params_array[port_id] =
- (struct kni_port_params*)rte_zmalloc("KNI_port_params",
- sizeof(struct kni_port_params), CACHE_LINE_SIZE);
+ rte_zmalloc("KNI_port_params",
+ sizeof(struct kni_port_params), RTE_CACHE_LINE_SIZE);
kni_port_params_array[port_id]->port_id = port_id;
kni_port_params_array[port_id]->lcore_rx =
(uint8_t)int_fld[i++];
return ret;
}
+/* Initialize KNI subsystem */
+static void
+init_kni(void)
+{
+ unsigned int num_of_kni_ports = 0, i;
+ struct kni_port_params **params = kni_port_params_array;
+
+ /* Calculate the maximum number of KNI interfaces that will be used */
+ for (i = 0; i < RTE_MAX_ETHPORTS; i++) {
+ if (kni_port_params_array[i]) {
+ num_of_kni_ports += (params[i]->nb_lcore_k ?
+ params[i]->nb_lcore_k : 1);
+ }
+ }
+
+ /* Invoke rte KNI init to preallocate the ports */
+ rte_kni_init(num_of_kni_ports);
+}
+
/* Initialise a single port on an Ethernet device */
static void
init_port(uint8_t port)
(unsigned)port, ret);
ret = rte_eth_rx_queue_setup(port, 0, NB_RXD,
- rte_eth_dev_socket_id(port), &rx_conf, pktmbuf_pool);
+ rte_eth_dev_socket_id(port), NULL, pktmbuf_pool);
if (ret < 0)
rte_exit(EXIT_FAILURE, "Could not setup up RX queue for "
"port%u (%d)\n", (unsigned)port, ret);
ret = rte_eth_tx_queue_setup(port, 0, NB_TXD,
- rte_eth_dev_socket_id(port), &tx_conf);
+ rte_eth_dev_socket_id(port), NULL);
if (ret < 0)
rte_exit(EXIT_FAILURE, "Could not setup up TX queue for "
"port%u (%d)\n", (unsigned)port, ret);
/* Get number of ports found in scan */
nb_sys_ports = rte_eth_dev_count();
if (nb_sys_ports == 0)
- rte_exit(EXIT_FAILURE, "No supported Ethernet devices found - "
- "check that CONFIG_RTE_LIBRTE_IGB_PMD=y and/or "
- "CONFIG_RTE_LIBRTE_IXGBE_PMD=y in the config file\n");
+ rte_exit(EXIT_FAILURE, "No supported Ethernet device found\n");
/* Check if the configured port ID is valid */
for (i = 0; i < RTE_MAX_ETHPORTS; i++)
rte_exit(EXIT_FAILURE, "Configured invalid "
"port ID %u\n", i);
+ /* Initialize KNI subsystem */
+ init_kni();
+
/* Initialise each port */
for (port = 0; port < nb_sys_ports; port++) {
/* Skip ports that are not enabled */