X-Git-Url: http://git.droids-corp.org/?a=blobdiff_plain;f=doc%2Fguides%2Fnics%2Fsfc_efx.rst;h=843c24991c0b27235a919d9a7f2fff04f7d74311;hb=735155ee3b7c126b14ac28c5667d5a2d811ddf4c;hp=f1489bea662034814e13f748c44c98f745aa6305;hpb=2ada1448d806e9d66b42f59f016e47f530956c49;p=dpdk.git

diff --git a/doc/guides/nics/sfc_efx.rst b/doc/guides/nics/sfc_efx.rst
index f1489bea66..843c24991c 100644
--- a/doc/guides/nics/sfc_efx.rst
+++ b/doc/guides/nics/sfc_efx.rst
@@ -1,5 +1,5 @@
 ..  SPDX-License-Identifier: BSD-3-Clause
-    Copyright(c) 2019-2020 Xilinx, Inc.
+    Copyright(c) 2019-2021 Xilinx, Inc.
     Copyright(c) 2016-2019 Solarflare Communications Inc.
 
     This software was jointly developed between OKTET Labs (under contract
@@ -74,6 +74,8 @@ SFC EFX PMD has support for:
 
 - SR-IOV PF
 
+- Port representors (see :ref: switch_representation)
+
 
 Non-supported Features
 ----------------------
@@ -190,6 +192,10 @@ Supported actions (***non-transfer*** rules):
 
 Supported pattern items (***transfer*** rules):
 
+- PORT_REPRESENTOR (cannot repeat; conflicts with other traffic source items)
+
+- PORT_ID (cannot repeat; conflicts with other traffic source items)
+
 - PHY_PORT (cannot repeat; conflicts with other traffic source items)
 
 - PF (cannot repeat; conflicts with other traffic source items)
@@ -198,6 +204,24 @@ Supported pattern items (***transfer*** rules):
 
 - ETH
 
+- VLAN (double-tagging is supported)
+
+- IPV4 (source/destination addresses, IP transport protocol,
+  type of service, time to live)
+
+- IPV6 (source/destination addresses, IP transport protocol,
+  traffic class, hop limit)
+
+- TCP (source/destination ports, TCP header length + TCP flags)
+
+- UDP (source/destination ports)
+
+- VXLAN (exact match of VXLAN network identifier)
+
+- GENEVE (exact match of virtual network identifier)
+
+- NVGRE (exact match of virtual subnet ID)
+
 Supported actions (***transfer*** rules):
 
 - OF_POP_VLAN
@@ -208,16 +232,32 @@ Supported actions (***transfer*** rules):
 
 - OF_VLAN_SET_PCP
 
+- VXLAN_DECAP
+
+- VXLAN_ENCAP
+
 - FLAG
 
 - MARK
 
 - PHY_PORT
 
+- PF
+
+- VF
+
+- PORT_ID
+
+- COUNT
+
+- DROP
+
 Validating flow rules depends on the firmware variant.
 
 The :ref:`flow_isolated_mode` is supported.
 
+The implementation is natively thread-safe.
+
 Ethernet destination individual/group match
 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 
@@ -322,11 +362,41 @@ Per-Device Parameters
 ~~~~~~~~~~~~~~~~~~~~~
 
 The following per-device parameters can be passed via EAL PCI device
-whitelist option like "-w 02:00.0,arg1=value1,...".
+allow option like "-a 02:00.0,arg1=value1,...".
 
 Case-insensitive 1/y/yes/on or 0/n/no/off may be used to specify
 boolean parameters value.
 
+- ``class`` [net|vdpa] (default **net**)
+
+  Choose the mode of operation of ef100 device.
+  **net** device will work as network device and will be probed by net/sfc driver.
+  **vdpa** device will work as vdpa device and will be probed by vdpa/sfc driver.
+  If this parameter is not specified then ef100 device will operate as
+  network device.
+
+- ``switch_mode`` [legacy|switchdev] (see below for default)
+
+  In legacy mode, NIC firmware provides Ethernet virtual bridging (EVB) API
+  to configure switching inside NIC to deliver traffic to physical (PF) and
+  virtual (VF) PCI functions. PF driver is responsible to build the
+  infrastructure for VFs, and traffic goes to/from VF by default in accordance
+  with MAC address assigned, permissions and filters installed by VF drivers.
+  In switchdev mode VF traffic goes via port representor (if any) on PF, and
+  software virtual switch (for example, Open vSwitch) makes the decision.
+  Software virtual switch may install MAE rules to pass established traffic
+  flows via hardware and offload software datapath as the result.
+  Default is legacy, unless representors are specified, in which case switchdev
+  is chosen.
+
+- ``representor`` parameter [list]
+
+  Instantiate port representor Ethernet devices for specified Virtual
+  Functions list.
+
+  It is a standard parameter whose format is described in
+  :ref:`ethernet_device_standard_device_arguments`.
+
 - ``rx_datapath`` [auto|efx|ef10|ef10_essb] (default **auto**)
 
   Choose receive datapath implementation.