X-Git-Url: http://git.droids-corp.org/?a=blobdiff_plain;f=doc%2Fguides%2Ftestpmd_app_ug%2Frun_app.rst;h=6745072329cbbedea27da8383f9c5e2ac02c2329;hb=039b769f7c018351fbadf240f7dd692d3b02518f;hp=216d9cd781d3070ecb73f0657f432f77a02b4c8b;hpb=0f2096d7ab3698c33600ddd67d3b9421691e11d5;p=dpdk.git

diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst
index 216d9cd781..6745072329 100644
--- a/doc/guides/testpmd_app_ug/run_app.rst
+++ b/doc/guides/testpmd_app_ug/run_app.rst
@@ -20,7 +20,7 @@ They must be separated from the EAL options, shown in the previous section, with
 
 .. code-block:: console
 
-    sudo ./testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2
+    sudo ./dpdk-testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2
 
 The command line options are:
 
@@ -59,19 +59,19 @@ The command line options are:
 *   ``--nb-cores=N``
 
     Set the number of forwarding cores,
-    where 1 <= N <= "number of cores" or ``CONFIG_RTE_MAX_LCORE`` from the configuration file.
+    where 1 <= N <= "number of cores" or ``RTE_MAX_LCORE`` from the configuration file.
     The default value is 1.
 
 *   ``--nb-ports=N``
 
     Set the number of forwarding ports,
-    where 1 <= N <= "number of ports" on the board or ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
+    where 1 <= N <= "number of ports" on the board or ``RTE_MAX_ETHPORTS`` from the configuration file.
     The default value is the number of ports on the board.
 
 *   ``--coremask=0xXX``
 
     Set the hexadecimal bitmask of the cores running the packet forwarding test.
-    The master lcore is reserved for command line parsing only and cannot be masked on for packet forwarding.
+    The main lcore is reserved for command line parsing only and cannot be masked on for packet forwarding.
 
 *   ``--portmask=0xXX``
 
@@ -138,7 +138,7 @@ The command line options are:
 *   ``--eth-peer=N,XX:XX:XX:XX:XX:XX``
 
     Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N,
-    where 0 <= N < ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
+    where 0 <= N < ``RTE_MAX_ETHPORTS``.
 
 *   ``--tx-ip=SRC,DST``
 
@@ -299,6 +299,13 @@ The command line options are:
     If set to 0, driver default is used if defined. Else, if driver
     default is not defined, default of 32 is used.
 
+*   ``--flowgen-clones=N``
+
+    Set the number of each packet clones to be sent in `flowgen` mode.
+    Sending clones reduces host CPU load on creating packets and may help
+    in testing extreme speeds or maxing out Tx packet performance.
+    N should be not zero, but less than 'burst' parameter.
+
 *   ``--mbcache=N``
 
     Set the cache of mbuf memory pools to N, where 0 <= N <= 512.
@@ -361,6 +368,12 @@ The command line options are:
 
     Don't flush the RX streams before starting forwarding. Used mainly with the PCAP PMD.
 
+*   ``--rxoffs=X[,Y]``
+
+    Set the offsets of packet segments on receiving if split
+    feature is engaged. Affects only the queues configured
+    with split offloads (currently BUFFER_SPLIT is supported only).
+
 *   ``--rxpkts=X[,Y]``
 
     Set the length of segments to scatter packets on receiving if split