X-Git-Url: http://git.droids-corp.org/?a=blobdiff_plain;f=doc%2Fguides%2Ftestpmd_app_ug%2Ftestpmd_funcs.rst;h=dcee5de455fa48d09ff481f9580721da69946343;hb=770fabcd36ec11d64544e86ed7d2dda9f5c64daf;hp=10aabf518a9603ee0f9e569abfd3735624161426;hpb=e1d44d0ad623825b4719e56ace937c368e7944c0;p=dpdk.git

diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
index 10aabf518a..dcee5de455 100644
--- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
+++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
@@ -539,6 +539,12 @@ Dumps the layout of all memory zones::
 
    testpmd> dump_memzone
 
+dump socket memory
+~~~~~~~~~~~~~~~~~~
+
+Dumps the memory usage of all sockets::
+
+   testpmd> dump_socket_mem
 
 dump struct size
 ~~~~~~~~~~~~~~~~
@@ -2317,6 +2323,16 @@ testpmd will add this value to any Tx packet sent from this port::
 
    testpmd> port config (port_id) tx_metadata (value)
 
+port config dynf
+~~~~~~~~~~~~~~~~
+
+Set/clear dynamic flag per port.
+testpmd will register this flag in the mbuf (same registration
+for both Tx and Rx). Then set/clear this flag for each Tx
+packet sent from this port. The set bit only works for Tx packet::
+
+   testpmd> port config (port_id) dynf (name) (set|clear)
+
 port config mtu
 ~~~~~~~~~~~~~~~
 
@@ -3594,6 +3610,10 @@ following sections.
 
    flow isolate {port_id} {boolean}
 
+- Dump internal representation information of all flows in hardware::
+
+   flow dump {port_id} {output_file}
+
 Validating flow rules
 ~~~~~~~~~~~~~~~~~~~~~
 
@@ -3969,6 +3989,19 @@ This section lists supported pattern items and their attributes, if any.
 
   - ``proto_id {unsigned}``: PPP protocol identifier.
 
+- ``l2tpv3oip``: match L2TPv3 over IP header.
+
+  - ``session_id {unsigned}``: L2TPv3 over IP session identifier.
+
+- ``ah``: match AH header.
+
+  - ``spi {unsigned}``: security parameters index.
+
+- ``pfcp``: match PFCP header.
+
+  - ``s_field {unsigned}``: S field.
+  - ``seid {unsigned}``: session endpoint identifier.
+
 Actions list
 ^^^^^^^^^^^^
 
@@ -4228,6 +4261,14 @@ This section lists supported actions and their attributes, if any.
 
   - ``value {unsigned}``: Value to decrease TCP acknowledgment number by.
 
+- ``set_ipv4_dscp``: Set IPv4 DSCP value with specified value
+
+  - ``dscp_value {unsigned}``: The new DSCP value to be set
+
+- ``set_ipv6_dscp``: Set IPv6 DSCP value with specified value
+
+  - ``dscp_value {unsigned}``: The new DSCP value to be set
+
 Destroying flow rules
 ~~~~~~~~~~~~~~~~~~~~~
 
@@ -4444,6 +4485,22 @@ Disabling isolated mode::
  Ingress traffic on port 0 is not restricted anymore to the defined flow rules
  testpmd>
 
+Dumping HW internal information
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+``flow dump`` dumps the hardware's internal representation information of
+all flows. It is bound to ``rte_flow_dev_dump()``::
+
+   flow dump {port_id} {output_file}
+
+If successful, it will show::
+
+   Flow dump finished
+
+Otherwise, it will complain error occurred::
+
+   Caught error type [...] ([...]): [...]
+
 Sample QinQ flow rules
 ~~~~~~~~~~~~~~~~~~~~~~
 
@@ -4766,6 +4823,49 @@ Decapsulating VxLAN::
  testpmd> flow create 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 /
         end actions raw_decap / queue index 0 / end
 
+Sample ESP rules
+~~~~~~~~~~~~~~~~
+
+ESP rules can be created by the following commands::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / esp spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 1 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / esp spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / esp spi is 1 / end
+        actions queue index 3 / end
+
+Sample AH rules
+~~~~~~~~~~~~~~~~
+
+AH rules can be created by the following commands::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / ah spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / ah spi is 1 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / ah spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / ah spi is 1 / end
+        actions queue index 3 / end
+
+Sample PFCP rules
+~~~~~~~~~~~~~~~~~
+
+PFCP rules can be created by the following commands(s_field need to be 1
+if seid is set)::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / pfcp s_field is 0 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / pfcp s_field is 1
+        seid is 1 / end actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / pfcp s_field is 0 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / pfcp s_field is 1
+        seid is 1 / end actions queue index 3 / end
+
 BPF Functions
 --------------