X-Git-Url: http://git.droids-corp.org/?a=blobdiff_plain;f=drivers%2Fnet%2Fixgbe%2Fbase%2Fixgbe_x550.c;h=f1f1fbe94d6b567482b62207d0ce3731ec084c96;hb=a2fdf99edfe4758de88ed20f716de668535be902;hp=0cc7a3f23b447d3a911a8173cc92136f7b39b360;hpb=d4b4c68454871bc7e9adb7b54c57cc2606978fe9;p=dpdk.git diff --git a/drivers/net/ixgbe/base/ixgbe_x550.c b/drivers/net/ixgbe/base/ixgbe_x550.c index 0cc7a3f23b..f1f1fbe94d 100644 --- a/drivers/net/ixgbe/base/ixgbe_x550.c +++ b/drivers/net/ixgbe/base/ixgbe_x550.c @@ -62,7 +62,7 @@ s32 ixgbe_init_ops_X550(struct ixgbe_hw *hw) mac->ops.dmac_config = ixgbe_dmac_config_X550; mac->ops.dmac_config_tcs = ixgbe_dmac_config_tcs_X550; mac->ops.dmac_update_tcs = ixgbe_dmac_update_tcs_X550; - mac->ops.setup_eee = ixgbe_setup_eee_X550; + mac->ops.setup_eee = NULL; mac->ops.set_source_address_pruning = ixgbe_set_source_address_pruning_X550; mac->ops.set_ethertype_anti_spoofing = @@ -83,6 +83,8 @@ s32 ixgbe_init_ops_X550(struct ixgbe_hw *hw) mac->ops.mdd_event = ixgbe_mdd_event_X550; mac->ops.restore_mdd_vf = ixgbe_restore_mdd_vf_X550; mac->ops.disable_rx = ixgbe_disable_rx_x550; + /* Manageability interface */ + mac->ops.set_fw_drv_ver = ixgbe_set_fw_drv_ver_x550; switch (hw->device_id) { case IXGBE_DEV_ID_X550EM_X_10G_T: case IXGBE_DEV_ID_X550EM_A_10G_T: @@ -454,17 +456,152 @@ STATIC s32 ixgbe_identify_phy_x550em(struct ixgbe_hw *hw) hw->phy.type = ixgbe_phy_x550em_kr; break; case IXGBE_DEV_ID_X550EM_A_10G_T: - case IXGBE_DEV_ID_X550EM_A_1G_T: - case IXGBE_DEV_ID_X550EM_A_1G_T_L: case IXGBE_DEV_ID_X550EM_X_1G_T: case IXGBE_DEV_ID_X550EM_X_10G_T: return ixgbe_identify_phy_generic(hw); + case IXGBE_DEV_ID_X550EM_A_1G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T_L: + hw->phy.type = ixgbe_phy_fw; + hw->phy.ops.read_reg = NULL; + hw->phy.ops.write_reg = NULL; + if (hw->bus.lan_id) + hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM; + else + hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY0_SM; + break; default: break; } return IXGBE_SUCCESS; } +/** + * ixgbe_fw_phy_activity - Perform an activity on a PHY + * @hw: pointer to hardware structure + * @activity: activity to perform + * @data: Pointer to 4 32-bit words of data + */ +s32 ixgbe_fw_phy_activity(struct ixgbe_hw *hw, u16 activity, + u32 (*data)[FW_PHY_ACT_DATA_COUNT]) +{ + union { + struct ixgbe_hic_phy_activity_req cmd; + struct ixgbe_hic_phy_activity_resp rsp; + } hic; + u16 retries = FW_PHY_ACT_RETRIES; + s32 rc; + u16 i; + + do { + memset(&hic, 0, sizeof(hic)); + hic.cmd.hdr.cmd = FW_PHY_ACT_REQ_CMD; + hic.cmd.hdr.buf_len = FW_PHY_ACT_REQ_LEN; + hic.cmd.hdr.checksum = FW_DEFAULT_CHECKSUM; + hic.cmd.port_number = hw->bus.lan_id; + hic.cmd.activity_id = IXGBE_CPU_TO_LE16(activity); + for (i = 0; i < FW_PHY_ACT_DATA_COUNT; ++i) + hic.cmd.data[i] = IXGBE_CPU_TO_BE32((*data)[i]); + + rc = ixgbe_host_interface_command(hw, (u32 *)&hic.cmd, + sizeof(hic.cmd), + IXGBE_HI_COMMAND_TIMEOUT, + true); + if (rc != IXGBE_SUCCESS) + return rc; + if (hic.rsp.hdr.cmd_or_resp.ret_status == + FW_CEM_RESP_STATUS_SUCCESS) { + for (i = 0; i < FW_PHY_ACT_DATA_COUNT; ++i) + (*data)[i] = IXGBE_BE32_TO_CPU(hic.rsp.data[i]); + return IXGBE_SUCCESS; + } + usec_delay(20); + --retries; + } while (retries > 0); + + return IXGBE_ERR_HOST_INTERFACE_COMMAND; +} + +static const struct { + u16 fw_speed; + ixgbe_link_speed phy_speed; +} ixgbe_fw_map[] = { + { FW_PHY_ACT_LINK_SPEED_10, IXGBE_LINK_SPEED_10_FULL }, + { FW_PHY_ACT_LINK_SPEED_100, IXGBE_LINK_SPEED_100_FULL }, + { FW_PHY_ACT_LINK_SPEED_1G, IXGBE_LINK_SPEED_1GB_FULL }, + { FW_PHY_ACT_LINK_SPEED_2_5G, IXGBE_LINK_SPEED_2_5GB_FULL }, + { FW_PHY_ACT_LINK_SPEED_5G, IXGBE_LINK_SPEED_5GB_FULL }, + { FW_PHY_ACT_LINK_SPEED_10G, IXGBE_LINK_SPEED_10GB_FULL }, +}; + +/** + * ixgbe_get_phy_id_fw - Get the phy ID via firmware command + * @hw: pointer to hardware structure + * + * Returns error code + */ +static s32 ixgbe_get_phy_id_fw(struct ixgbe_hw *hw) +{ + u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 }; + u16 phy_speeds; + u16 phy_id_lo; + s32 rc; + u16 i; + + rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_PHY_INFO, &info); + if (rc) + return rc; + + hw->phy.speeds_supported = 0; + phy_speeds = info[0] & FW_PHY_INFO_SPEED_MASK; + for (i = 0; i < sizeof(ixgbe_fw_map) / sizeof(ixgbe_fw_map[0]); ++i) { + if (phy_speeds & ixgbe_fw_map[i].fw_speed) + hw->phy.speeds_supported |= ixgbe_fw_map[i].phy_speed; + } + if (!hw->phy.autoneg_advertised) + hw->phy.autoneg_advertised = hw->phy.speeds_supported; + + hw->phy.id = info[0] & FW_PHY_INFO_ID_HI_MASK; + phy_id_lo = info[1] & FW_PHY_INFO_ID_LO_MASK; + hw->phy.id |= phy_id_lo & IXGBE_PHY_REVISION_MASK; + hw->phy.revision = phy_id_lo & ~IXGBE_PHY_REVISION_MASK; + if (!hw->phy.id || hw->phy.id == IXGBE_PHY_REVISION_MASK) + return IXGBE_ERR_PHY_ADDR_INVALID; + return IXGBE_SUCCESS; +} + +/** + * ixgbe_identify_phy_fw - Get PHY type based on firmware command + * @hw: pointer to hardware structure + * + * Returns error code + */ +static s32 ixgbe_identify_phy_fw(struct ixgbe_hw *hw) +{ + if (hw->bus.lan_id) + hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY1_SM; + else + hw->phy.phy_semaphore_mask = IXGBE_GSSR_PHY0_SM; + + hw->phy.type = ixgbe_phy_fw; + hw->phy.ops.read_reg = NULL; + hw->phy.ops.write_reg = NULL; + return ixgbe_get_phy_id_fw(hw); +} + +/** + * ixgbe_shutdown_fw_phy - Shutdown a firmware-controlled PHY + * @hw: pointer to hardware structure + * + * Returns error code + */ +s32 ixgbe_shutdown_fw_phy(struct ixgbe_hw *hw) +{ + u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 }; + + setup[0] = FW_PHY_ACT_FORCE_LINK_DOWN_OFF; + return ixgbe_fw_phy_activity(hw, FW_PHY_ACT_FORCE_LINK_DOWN, &setup); +} + STATIC s32 ixgbe_read_phy_reg_x550em(struct ixgbe_hw *hw, u32 reg_addr, u32 device_type, u16 *phy_data) { @@ -601,18 +738,20 @@ s32 ixgbe_init_ops_X550EM(struct ixgbe_hw *hw) else mac->ops.setup_fc = ixgbe_setup_fc_X550em; + /* PHY */ + phy->ops.init = ixgbe_init_phy_ops_X550em; switch (hw->device_id) { - case IXGBE_DEV_ID_X550EM_X_KR: - case IXGBE_DEV_ID_X550EM_A_KR: - case IXGBE_DEV_ID_X550EM_A_KR_L: + case IXGBE_DEV_ID_X550EM_A_1G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T_L: + mac->ops.setup_fc = NULL; + phy->ops.identify = ixgbe_identify_phy_fw; + phy->ops.set_phy_power = NULL; + phy->ops.get_firmware_version = NULL; break; default: - mac->ops.setup_eee = NULL; + phy->ops.identify = ixgbe_identify_phy_x550em; } - /* PHY */ - phy->ops.init = ixgbe_init_phy_ops_X550em; - phy->ops.identify = ixgbe_identify_phy_x550em; if (mac->ops.get_media_type(hw) != ixgbe_media_type_copper) phy->ops.set_phy_power = NULL; @@ -630,6 +769,92 @@ s32 ixgbe_init_ops_X550EM(struct ixgbe_hw *hw) return ret_val; } +/** + * ixgbe_setup_fw_link - Setup firmware-controlled PHYs + * @hw: pointer to hardware structure + */ +static s32 ixgbe_setup_fw_link(struct ixgbe_hw *hw) +{ + u32 setup[FW_PHY_ACT_DATA_COUNT] = { 0 }; + s32 rc; + u16 i; + + if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw)) + return 0; + + if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { + ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, + "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); + return IXGBE_ERR_INVALID_LINK_SETTINGS; + } + + switch (hw->fc.requested_mode) { + case ixgbe_fc_full: + setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RXTX << + FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT; + break; + case ixgbe_fc_rx_pause: + setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_RX << + FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT; + break; + case ixgbe_fc_tx_pause: + setup[0] |= FW_PHY_ACT_SETUP_LINK_PAUSE_TX << + FW_PHY_ACT_SETUP_LINK_PAUSE_SHIFT; + break; + default: + break; + } + + for (i = 0; i < sizeof(ixgbe_fw_map) / sizeof(ixgbe_fw_map[0]); ++i) { + if (hw->phy.autoneg_advertised & ixgbe_fw_map[i].phy_speed) + setup[0] |= ixgbe_fw_map[i].fw_speed; + } + setup[0] |= FW_PHY_ACT_SETUP_LINK_HP | FW_PHY_ACT_SETUP_LINK_AN; + + if (hw->phy.eee_speeds_advertised) + setup[0] |= FW_PHY_ACT_SETUP_LINK_EEE; + + rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_SETUP_LINK, &setup); + if (rc) + return rc; + if (setup[0] == FW_PHY_ACT_SETUP_LINK_RSP_DOWN) + return IXGBE_ERR_OVERTEMP; + return IXGBE_SUCCESS; +} + +/** + * ixgbe_fc_autoneg_fw _ Set up flow control for FW-controlled PHYs + * @hw: pointer to hardware structure + * + * Called at init time to set up flow control. + */ +static s32 ixgbe_fc_autoneg_fw(struct ixgbe_hw *hw) +{ + if (hw->fc.requested_mode == ixgbe_fc_default) + hw->fc.requested_mode = ixgbe_fc_full; + + return ixgbe_setup_fw_link(hw); +} + +/** + * ixgbe_setup_eee_fw - Enable/disable EEE support + * @hw: pointer to the HW structure + * @enable_eee: boolean flag to enable EEE + * + * Enable/disable EEE based on enable_eee flag. + * This function controls EEE for firmware-based PHY implementations. + */ +static s32 ixgbe_setup_eee_fw(struct ixgbe_hw *hw, bool enable_eee) +{ + if (!!hw->phy.eee_speeds_advertised == enable_eee) + return IXGBE_SUCCESS; + if (enable_eee) + hw->phy.eee_speeds_advertised = hw->phy.eee_speeds_supported; + else + hw->phy.eee_speeds_advertised = 0; + return hw->phy.ops.setup_link(hw); +} + /** * ixgbe_init_ops_X550EM_a - Inits func ptrs and MAC type * @hw: pointer to hardware structure @@ -660,7 +885,7 @@ s32 ixgbe_init_ops_X550EM_a(struct ixgbe_hw *hw) switch (mac->ops.get_media_type(hw)) { case ixgbe_media_type_fiber: - mac->ops.setup_fc = ixgbe_setup_fc_fiber_x550em_a; + mac->ops.setup_fc = NULL; mac->ops.fc_autoneg = ixgbe_fc_autoneg_fiber_x550em_a; break; case ixgbe_media_type_backplane: @@ -674,7 +899,16 @@ s32 ixgbe_init_ops_X550EM_a(struct ixgbe_hw *hw) if ((hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T) || (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L)) { mac->ops.fc_autoneg = ixgbe_fc_autoneg_sgmii_x550em_a; - mac->ops.setup_fc = ixgbe_setup_fc_sgmii_x550em_a; + mac->ops.setup_fc = ixgbe_fc_autoneg_fw; + } + + switch (hw->device_id) { + case IXGBE_DEV_ID_X550EM_A_KR: + case IXGBE_DEV_ID_X550EM_A_KR_L: + mac->ops.setup_eee = ixgbe_setup_eee_fw; + break; + default: + mac->ops.setup_eee = NULL; } return ret_val; @@ -881,45 +1115,27 @@ s32 ixgbe_init_eeprom_params_X550(struct ixgbe_hw *hw) */ STATIC s32 ixgbe_enable_eee_x550(struct ixgbe_hw *hw) { - u16 autoneg_eee_reg; u32 link_reg; s32 status; - if (hw->mac.type == ixgbe_mac_X550) { - /* Advertise EEE capability */ - hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, - &autoneg_eee_reg); - - autoneg_eee_reg |= (IXGBE_AUTO_NEG_10GBASE_EEE_ADVT | - IXGBE_AUTO_NEG_1000BASE_EEE_ADVT | - IXGBE_AUTO_NEG_100BASE_EEE_ADVT); - - hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, - autoneg_eee_reg); - return IXGBE_SUCCESS; - } - switch (hw->device_id) { - case IXGBE_DEV_ID_X550EM_X_KR: case IXGBE_DEV_ID_X550EM_A_KR: case IXGBE_DEV_ID_X550EM_A_KR_L: status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg); if (status != IXGBE_SUCCESS) return status; link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KR | - IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX; + IXGBE_KRM_LINK_CTRL_1_TETH_EEE_CAP_KX; /* Don't advertise FEC capability when EEE enabled. */ link_reg &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg); if (status != IXGBE_SUCCESS) return status; break; @@ -936,33 +1152,16 @@ STATIC s32 ixgbe_enable_eee_x550(struct ixgbe_hw *hw) */ STATIC s32 ixgbe_disable_eee_x550(struct ixgbe_hw *hw) { - u16 autoneg_eee_reg; u32 link_reg; s32 status; - if (hw->mac.type == ixgbe_mac_X550) { - /* Disable advertised EEE capability */ - hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, - &autoneg_eee_reg); - - autoneg_eee_reg &= ~(IXGBE_AUTO_NEG_10GBASE_EEE_ADVT | - IXGBE_AUTO_NEG_1000BASE_EEE_ADVT | - IXGBE_AUTO_NEG_100BASE_EEE_ADVT); - - hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_EEE_ADVT, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, - autoneg_eee_reg); - return IXGBE_SUCCESS; - } - switch (hw->device_id) { case IXGBE_DEV_ID_X550EM_X_KR: case IXGBE_DEV_ID_X550EM_A_KR: case IXGBE_DEV_ID_X550EM_A_KR_L: status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, &link_reg); if (status != IXGBE_SUCCESS) return status; @@ -973,8 +1172,8 @@ STATIC s32 ixgbe_disable_eee_x550(struct ixgbe_hw *hw) link_reg |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_FEC; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, link_reg); if (status != IXGBE_SUCCESS) return status; break; @@ -1007,11 +1206,6 @@ s32 ixgbe_setup_eee_X550(struct ixgbe_hw *hw, bool enable_eee) if (enable_eee) { eeer |= (IXGBE_EEER_TX_LPI_EN | IXGBE_EEER_RX_LPI_EN); - /* Not supported on first revision of X550EM_x. */ - if ((hw->mac.type == ixgbe_mac_X550EM_x) && - !(IXGBE_FUSES0_REV_MASK & - IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0)))) - return IXGBE_SUCCESS; status = ixgbe_enable_eee_x550(hw); if (status) return status; @@ -1720,12 +1914,12 @@ STATIC s32 ixgbe_setup_sgmii(struct ixgbe_hw *hw, ixgbe_link_speed speed, return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait); } - /** - * ixgbe_setup_sgmii_m88 - Set up link for sgmii with Marvell PHYs +/** + * ixgbe_setup_sgmii_fw - Set up link for sgmii with firmware-controlled PHYs * @hw: pointer to hardware structure */ -STATIC s32 ixgbe_setup_sgmii_m88(struct ixgbe_hw *hw, ixgbe_link_speed speed, - bool autoneg_wait) +STATIC s32 ixgbe_setup_sgmii_fw(struct ixgbe_hw *hw, ixgbe_link_speed speed, + bool autoneg_wait) { struct ixgbe_mac_info *mac = &hw->mac; u32 lval, sval, flx_val; @@ -1775,7 +1969,7 @@ STATIC s32 ixgbe_setup_sgmii_m88(struct ixgbe_hw *hw, ixgbe_link_speed speed, return rc; flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK; - flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_1G; + flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN; flx_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN; flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN; flx_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN; @@ -1812,19 +2006,22 @@ void ixgbe_init_mac_link_ops_X550em(struct ixgbe_hw *hw) mac->ops.setup_link = ixgbe_setup_mac_link_multispeed_fiber; mac->ops.set_rate_select_speed = ixgbe_set_soft_rate_select_speed; + if ((hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP_N) || (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP)) mac->ops.setup_mac_link = - ixgbe_setup_mac_link_sfp_x550a; + ixgbe_setup_mac_link_sfp_x550a; else mac->ops.setup_mac_link = - ixgbe_setup_mac_link_sfp_x550em; + ixgbe_setup_mac_link_sfp_x550em; break; case ixgbe_media_type_copper: if (hw->mac.type == ixgbe_mac_X550EM_a) { if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T || hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L) { - mac->ops.setup_link = ixgbe_setup_sgmii_m88; + mac->ops.setup_link = ixgbe_setup_sgmii_fw; + mac->ops.check_link = + ixgbe_check_mac_link_generic; } else { mac->ops.setup_link = ixgbe_setup_mac_link_t_X550em; @@ -1856,6 +2053,13 @@ s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw, { DEBUGFUNC("ixgbe_get_link_capabilities_X550em"); + + if (hw->phy.type == ixgbe_phy_fw) { + *autoneg = true; + *speed = hw->phy.speeds_supported; + return 0; + } + /* SFP */ if (hw->phy.media_type == ixgbe_media_type_fiber) { @@ -1879,14 +2083,23 @@ s32 ixgbe_get_link_capabilities_X550em(struct ixgbe_hw *hw, *speed = IXGBE_LINK_SPEED_10GB_FULL; } else { switch (hw->phy.type) { - case ixgbe_phy_m88: - *speed = IXGBE_LINK_SPEED_1GB_FULL | - IXGBE_LINK_SPEED_100_FULL | - IXGBE_LINK_SPEED_10_FULL; - break; case ixgbe_phy_sgmii: *speed = IXGBE_LINK_SPEED_1GB_FULL; break; + case ixgbe_phy_x550em_kr: + if (hw->mac.type == ixgbe_mac_X550EM_a) { + /* check different backplane modes */ + if (hw->phy.nw_mng_if_sel & + IXGBE_NW_MNG_IF_SEL_PHY_SPEED_2_5G) { + *speed = IXGBE_LINK_SPEED_2_5GB_FULL; + break; + } else if (hw->device_id == + IXGBE_DEV_ID_X550EM_A_KR_L) { + *speed = IXGBE_LINK_SPEED_1GB_FULL; + break; + } + } + /* fall through */ default: *speed = IXGBE_LINK_SPEED_10GB_FULL | IXGBE_LINK_SPEED_1GB_FULL; @@ -2007,19 +2220,32 @@ STATIC s32 ixgbe_enable_lasi_ext_t_x550em(struct ixgbe_hw *hw) status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc); /* Enable link status change alarm */ - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®); - if (status != IXGBE_SUCCESS) - return status; + /* Enable the LASI interrupts on X552 devices to receive notifications + * of the link configurations of the external PHY and correspondingly + * support the configuration of the internal iXFI link, since iXFI does + * not support auto-negotiation. This is not required for X553 devices + * having KR support, which performs auto-negotiations and which is used + * as the internal link to the external PHY. Hence adding a check here + * to avoid enabling LASI interrupts for X553 devices. + */ + if (hw->mac.type != ixgbe_mac_X550EM_a) { + status = hw->phy.ops.read_reg(hw, + IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK, + IXGBE_MDIO_AUTO_NEG_DEV_TYPE, ®); - reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN; + if (status != IXGBE_SUCCESS) + return status; - status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg); + reg |= IXGBE_MDIO_PMA_TX_VEN_LASI_INT_EN; - if (status != IXGBE_SUCCESS) - return status; + status = hw->phy.ops.write_reg(hw, + IXGBE_MDIO_PMA_TX_VEN_LASI_INT_MASK, + IXGBE_MDIO_AUTO_NEG_DEV_TYPE, reg); + + if (status != IXGBE_SUCCESS) + return status; + } /* Enable high temperature failure and global fault alarms */ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_GLOBAL_INT_MASK, @@ -2088,8 +2314,8 @@ STATIC s32 ixgbe_setup_kr_speed_x550em(struct ixgbe_hw *hw, u32 reg_val; status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); if (status) return status; @@ -2106,297 +2332,89 @@ STATIC s32 ixgbe_setup_kr_speed_x550em(struct ixgbe_hw *hw, reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CAP_KX; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); - if (status) - return status; + if (hw->mac.type == ixgbe_mac_X550EM_a) { + /* Set lane mode to KR auto negotiation */ + status = hw->mac.ops.read_iosf_sb_reg(hw, + IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); - reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK; - reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN; - reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN; - reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN; - reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN; + if (status) + return status; - status = hw->mac.ops.write_iosf_sb_reg(hw, + reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_MASK; + reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_SPEED_AN; + reg_val |= IXGBE_KRM_PMD_FLX_MASK_ST20_AN_EN; + reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_AN37_EN; + reg_val &= ~IXGBE_KRM_PMD_FLX_MASK_ST20_SGMII_EN; + + status = hw->mac.ops.write_iosf_sb_reg(hw, IXGBE_KRM_PMD_FLX_MASK_ST20(hw->bus.lan_id), IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + } return ixgbe_restart_an_internal_phy_x550em(hw); } /** - * ixgbe_setup_m88 - setup m88 PHY + * ixgbe_reset_phy_fw - Reset firmware-controlled PHYs * @hw: pointer to hardware structure */ -STATIC s32 ixgbe_setup_m88(struct ixgbe_hw *hw) +static s32 ixgbe_reset_phy_fw(struct ixgbe_hw *hw) { - u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM; - u16 reg; + u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 }; s32 rc; if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw)) return IXGBE_SUCCESS; - rc = hw->mac.ops.acquire_swfw_sync(hw, mask); + rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_PHY_SW_RESET, &store); if (rc) return rc; + memset(store, 0, sizeof(store)); - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®); - if (rc) - goto out; - if (reg & IXGBE_M88E1500_COPPER_CTRL_POWER_DOWN) { - reg &= ~IXGBE_M88E1500_COPPER_CTRL_POWER_DOWN; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, - reg); - } - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, ®); - if (rc) - goto out; - if (reg & IXGBE_M88E1500_MAC_CTRL_1_POWER_DOWN) { - reg &= ~IXGBE_M88E1500_MAC_CTRL_1_POWER_DOWN; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, - reg); - } - - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 2); - if (rc) - goto out; - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_MAC_SPEC_CTRL, 0, - ®); - if (rc) - goto out; - if (reg & IXGBE_M88E1500_MAC_SPEC_CTRL_POWER_DOWN) { - reg &= ~IXGBE_M88E1500_MAC_SPEC_CTRL_POWER_DOWN; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_SPEC_CTRL, 0, - reg); - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, - 0); - if (rc) - goto out; - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, - ®); - if (rc) - goto out; - reg |= IXGBE_M88E1500_COPPER_CTRL_RESET; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, - reg); - usec_delay(50); - } else { - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, - 0); - if (rc) - goto out; - } - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®); - if (rc) - goto out; - - if (!(reg & IXGBE_M88E1500_COPPER_CTRL_AN_EN)) { - reg |= IXGBE_M88E1500_COPPER_CTRL_AN_EN; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, - reg); - } - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_1000T_CTRL, 0, ®); - if (rc) - goto out; - reg &= ~IXGBE_M88E1500_1000T_CTRL_HALF_DUPLEX; - reg &= ~IXGBE_M88E1500_1000T_CTRL_FULL_DUPLEX; - if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_1GB_FULL) - reg |= IXGBE_M88E1500_1000T_CTRL_FULL_DUPLEX; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_1000T_CTRL, 0, reg); - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_AN, 0, ®); - if (rc) - goto out; - reg &= ~IXGBE_M88E1500_COPPER_AN_T4; - reg &= ~IXGBE_M88E1500_COPPER_AN_100TX_FD; - reg &= ~IXGBE_M88E1500_COPPER_AN_100TX_HD; - reg &= ~IXGBE_M88E1500_COPPER_AN_10TX_FD; - reg &= ~IXGBE_M88E1500_COPPER_AN_10TX_HD; - - /* Flow control auto negotiation configuration was moved from here to - * the function ixgbe_setup_fc_sgmii_x550em_a() - */ - - if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_100_FULL) - reg |= IXGBE_M88E1500_COPPER_AN_100TX_FD; - if (hw->phy.autoneg_advertised & IXGBE_LINK_SPEED_10_FULL) - reg |= IXGBE_M88E1500_COPPER_AN_10TX_FD; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_AN, 0, reg); - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®); + rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_INIT_PHY, &store); if (rc) - goto out; - reg |= IXGBE_M88E1500_COPPER_CTRL_RESTART_AN; - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg); - - - hw->mac.ops.release_swfw_sync(hw, mask); - return rc; + return rc; -out: - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0); - hw->mac.ops.release_swfw_sync(hw, mask); - return rc; + return ixgbe_setup_fw_link(hw); } /** - * ixgbe_reset_phy_m88e1500 - Reset m88e1500 PHY + * ixgbe_check_overtemp_fw - Check firmware-controlled PHYs for overtemp * @hw: pointer to hardware structure - * - * The PHY token must be held when calling this function. */ -static s32 ixgbe_reset_phy_m88e1500(struct ixgbe_hw *hw) +static s32 ixgbe_check_overtemp_fw(struct ixgbe_hw *hw) { - u16 reg; + u32 store[FW_PHY_ACT_DATA_COUNT] = { 0 }; s32 rc; - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0); - if (rc) - return rc; - - rc = hw->phy.ops.read_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, ®); + rc = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &store); if (rc) return rc; - reg |= IXGBE_M88E1500_COPPER_CTRL_RESET; - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg); - - usec_delay(10); - - return rc; + if (store[0] & FW_PHY_ACT_GET_LINK_INFO_TEMP) { + ixgbe_shutdown_fw_phy(hw); + return IXGBE_ERR_OVERTEMP; + } + return IXGBE_SUCCESS; } /** - * ixgbe_reset_phy_m88e1543 - Reset m88e1543 PHY - * @hw: pointer to hardware structure + * ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register + * @hw: pointer to hardware structure * - * The PHY token must be held when calling this function. - */ -static s32 ixgbe_reset_phy_m88e1543(struct ixgbe_hw *hw) + * Read NW_MNG_IF_SEL register and save field values, and check for valid field + * values. + **/ +STATIC s32 ixgbe_read_mng_if_sel_x550em(struct ixgbe_hw *hw) { - return hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0); -} - -/** - * ixgbe_reset_phy_m88 - Reset m88 PHY - * @hw: pointer to hardware structure - */ -STATIC s32 ixgbe_reset_phy_m88(struct ixgbe_hw *hw) -{ - u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM; - u16 reg; - s32 rc; - - if (hw->phy.reset_disable || ixgbe_check_reset_blocked(hw)) - return IXGBE_SUCCESS; - - rc = hw->mac.ops.acquire_swfw_sync(hw, mask); - if (rc) - return rc; - - switch (hw->phy.id) { - case IXGBE_M88E1500_E_PHY_ID: - rc = ixgbe_reset_phy_m88e1500(hw); - break; - case IXGBE_M88E1543_E_PHY_ID: - rc = ixgbe_reset_phy_m88e1543(hw); - break; - default: - rc = IXGBE_ERR_PHY; - break; - } - - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1); - if (rc) - goto out; - - reg = IXGBE_M88E1500_FIBER_CTRL_RESET | - IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL | - IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB; - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_FIBER_CTRL, 0, reg); - if (rc) - goto out; - - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 18); - if (rc) - goto out; - - reg = IXGBE_M88E1500_GEN_CTRL_RESET | - IXGBE_M88E1500_GEN_CTRL_MODE_SGMII_COPPER; - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_GEN_CTRL, 0, reg); - if (rc) - goto out; - - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 1); - if (rc) - goto out; - - reg = IXGBE_M88E1500_FIBER_CTRL_RESET | - IXGBE_M88E1500_FIBER_CTRL_AN_EN | - IXGBE_M88E1500_FIBER_CTRL_DUPLEX_FULL | - IXGBE_M88E1500_FIBER_CTRL_SPEED_MSB; - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_FIBER_CTRL, 0, reg); - if (rc) - goto out; - - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0); - if (rc) - goto out; - - reg = (IXGBE_M88E1500_MAC_CTRL_1_DWN_4X << - IXGBE_M88E1500_MAC_CTRL_1_DWN_SHIFT) | - (IXGBE_M88E1500_MAC_CTRL_1_ED_TM << - IXGBE_M88E1500_MAC_CTRL_1_ED_SHIFT) | - (IXGBE_M88E1500_MAC_CTRL_1_MDIX_AUTO << - IXGBE_M88E1500_MAC_CTRL_1_MDIX_SHIFT); - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_MAC_CTRL_1, 0, reg); - if (rc) - goto out; - - reg = IXGBE_M88E1500_COPPER_CTRL_RESET | - IXGBE_M88E1500_COPPER_CTRL_AN_EN | - IXGBE_M88E1500_COPPER_CTRL_RESTART_AN | - IXGBE_M88E1500_COPPER_CTRL_FULL_DUPLEX | - IXGBE_M88E1500_COPPER_CTRL_SPEED_MSB; - rc = hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_COPPER_CTRL, 0, reg); - if (rc) - goto out; - - hw->mac.ops.release_swfw_sync(hw, mask); - - /* In case of first reset set advertised speeds to default value */ - if (!hw->phy.autoneg_advertised) - hw->phy.autoneg_advertised = IXGBE_LINK_SPEED_1GB_FULL | - IXGBE_LINK_SPEED_100_FULL | - IXGBE_LINK_SPEED_10_FULL; - - return ixgbe_setup_m88(hw); - -out: - hw->phy.ops.write_reg_mdi(hw, IXGBE_M88E1500_PAGE_ADDR, 0, 0); - hw->mac.ops.release_swfw_sync(hw, mask); - return rc; -} - -/** - * ixgbe_read_mng_if_sel_x550em - Read NW_MNG_IF_SEL register - * @hw: pointer to hardware structure - * - * Read NW_MNG_IF_SEL register and save field values, and check for valid field - * values. - **/ -STATIC s32 ixgbe_read_mng_if_sel_x550em(struct ixgbe_hw *hw) -{ - /* Save NW management interface connected on board. This is used - * to determine internal PHY mode. - */ - hw->phy.nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL); + /* Save NW management interface connected on board. This is used + * to determine internal PHY mode. + */ + hw->phy.nw_mng_if_sel = IXGBE_READ_REG(hw, IXGBE_NW_MNG_IF_SEL); /* If X552 (X550EM_a) and MDIO is connected to external PHY, then set * PHY address. This register field was has only been used for X552. @@ -2405,7 +2423,7 @@ STATIC s32 ixgbe_read_mng_if_sel_x550em(struct ixgbe_hw *hw) hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_MDIO_ACT) { hw->phy.addr = (hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD) >> - IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD_SHIFT; + IXGBE_NW_MNG_IF_SEL_MDIO_PHY_ADD_SHIFT; } return IXGBE_SUCCESS; @@ -2426,6 +2444,9 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) DEBUGFUNC("ixgbe_init_phy_ops_X550em"); + hw->mac.ops.set_lan_id(hw); + ixgbe_read_mng_if_sel_x550em(hw); + if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber) { phy->phy_semaphore_mask = IXGBE_GSSR_SHARED_I2C_SM; ixgbe_setup_mux_ctl(hw); @@ -2439,6 +2460,7 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) phy->ops.write_reg_mdi = ixgbe_write_phy_reg_mdi_22; hw->phy.ops.read_reg = ixgbe_read_phy_reg_x550a; hw->phy.ops.write_reg = ixgbe_write_phy_reg_x550a; + phy->ops.check_overtemp = ixgbe_check_overtemp_fw; if (hw->bus.lan_id) hw->phy.phy_semaphore_mask |= IXGBE_GSSR_PHY1_SM; else @@ -2464,7 +2486,8 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) /* Identify the PHY or SFP module */ ret_val = phy->ops.identify(hw); - if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED) + if (ret_val == IXGBE_ERR_SFP_NOT_SUPPORTED || + ret_val == IXGBE_ERR_PHY_ADDR_INVALID) return ret_val; /* Setup function pointers based on detected hardware */ @@ -2503,9 +2526,9 @@ s32 ixgbe_init_phy_ops_X550em(struct ixgbe_hw *hw) case ixgbe_phy_sgmii: phy->ops.setup_link = NULL; break; - case ixgbe_phy_m88: - phy->ops.setup_link = ixgbe_setup_m88; - phy->ops.reset = ixgbe_reset_phy_m88; + case ixgbe_phy_fw: + phy->ops.setup_link = ixgbe_setup_fw_link; + phy->ops.reset = ixgbe_reset_phy_fw; break; default: break; @@ -2525,8 +2548,6 @@ STATIC void ixgbe_set_mdio_speed(struct ixgbe_hw *hw) case IXGBE_DEV_ID_X550EM_X_10G_T: case IXGBE_DEV_ID_X550EM_A_SGMII: case IXGBE_DEV_ID_X550EM_A_SGMII_L: - case IXGBE_DEV_ID_X550EM_A_1G_T: - case IXGBE_DEV_ID_X550EM_A_1G_T_L: case IXGBE_DEV_ID_X550EM_A_10G_T: case IXGBE_DEV_ID_X550EM_A_SFP: case IXGBE_DEV_ID_X550EM_A_QSFP: @@ -2535,6 +2556,13 @@ STATIC void ixgbe_set_mdio_speed(struct ixgbe_hw *hw) hlreg0 &= ~IXGBE_HLREG0_MDCSPD; IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0); break; + case IXGBE_DEV_ID_X550EM_A_1G_T: + case IXGBE_DEV_ID_X550EM_A_1G_T_L: + /* Select fast MDIO clock speed for these devices */ + hlreg0 = IXGBE_READ_REG(hw, IXGBE_HLREG0); + hlreg0 |= IXGBE_HLREG0_MDCSPD; + IXGBE_WRITE_REG(hw, IXGBE_HLREG0, hlreg0); + break; default: break; } @@ -2591,8 +2619,10 @@ s32 ixgbe_reset_hw_X550em(struct ixgbe_hw *hw) return status; /* Reset PHY */ - if (!hw->phy.reset_disable && hw->phy.ops.reset) - hw->phy.ops.reset(hw); + if (!hw->phy.reset_disable && hw->phy.ops.reset) { + if (hw->phy.ops.reset(hw) == IXGBE_ERR_OVERTEMP) + return IXGBE_ERR_OVERTEMP; + } mac_reset_top: /* Issue global reset to the MAC. Needs to be SW reset if link is up. @@ -2738,18 +2768,53 @@ s32 ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw, if (ret_val != IXGBE_SUCCESS) return ret_val; - /* Configure internal PHY for KR/KX. */ - ixgbe_setup_kr_speed_x550em(hw, speed); - - /* Configure CS4227 LINE side to proper mode. */ - reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + - (hw->bus.lan_id << 12); - if (setup_linear) - reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1; - else + if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { + /* Configure CS4227 LINE side to 10G SR. */ + reg_slice = IXGBE_CS4227_LINE_SPARE22_MSB + + (hw->bus.lan_id << 12); + reg_val = IXGBE_CS4227_SPEED_10G; + ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice, + reg_val); + + reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + + (hw->bus.lan_id << 12); reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; - ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice, - reg_val); + ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice, + reg_val); + + /* Configure CS4227 for HOST connection rate then type. */ + reg_slice = IXGBE_CS4227_HOST_SPARE22_MSB + + (hw->bus.lan_id << 12); + reg_val = (speed & IXGBE_LINK_SPEED_10GB_FULL) ? + IXGBE_CS4227_SPEED_10G : IXGBE_CS4227_SPEED_1G; + ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice, + reg_val); + + reg_slice = IXGBE_CS4227_HOST_SPARE24_LSB + + (hw->bus.lan_id << 12); + if (setup_linear) + reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1; + else + reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; + ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice, + reg_val); + + /* Setup XFI internal link. */ + ret_val = ixgbe_setup_ixfi_x550em(hw, &speed); + } else { + /* Configure internal PHY for KR/KX. */ + ixgbe_setup_kr_speed_x550em(hw, speed); + + /* Configure CS4227 LINE side to proper mode. */ + reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + + (hw->bus.lan_id << 12); + if (setup_linear) + reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1; + else + reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; + ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice, + reg_val); + } return ret_val; } @@ -2809,8 +2874,8 @@ STATIC s32 ixgbe_setup_sfi_x550a(struct ixgbe_hw *hw, ixgbe_link_speed *speed) * Configure the the integrated PHY for SFP support. **/ s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, - ixgbe_link_speed speed, - bool autoneg_wait_to_complete) + ixgbe_link_speed speed, + bool autoneg_wait_to_complete) { s32 ret_val; u16 reg_phy_ext; @@ -2863,9 +2928,9 @@ s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, return IXGBE_ERR_PHY_ADDR_INVALID; } - /* Get external PHY device id */ - ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_GLOBAL_ID_MSB, - IXGBE_MDIO_ZERO_DEV_TYPE, ®_phy_ext); + /* Get external PHY SKU id */ + ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_EFUSE_PDF_SKU, + IXGBE_MDIO_ZERO_DEV_TYPE, ®_phy_ext); if (ret_val != IXGBE_SUCCESS) return ret_val; @@ -2873,7 +2938,7 @@ s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, /* When configuring quad port CS4223, the MAC instance is part * of the slice offset. */ - if (reg_phy_ext == IXGBE_CS4223_PHY_ID) + if (reg_phy_ext == IXGBE_CS4223_SKU_ID) slice_offset = (hw->bus.lan_id + (hw->bus.instance_id << 1)) << 12; else @@ -2886,7 +2951,7 @@ s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw, else reg_phy_ext = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1; ret_val = hw->phy.ops.write_reg(hw, reg_slice, - IXGBE_MDIO_ZERO_DEV_TYPE, reg_phy_ext); + IXGBE_MDIO_ZERO_DEV_TYPE, reg_phy_ext); } return ret_val; } @@ -2974,6 +3039,10 @@ STATIC s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed) s32 status; u32 reg_val; + /* iXFI is only supported with X552 */ + if (mac->type != ixgbe_mac_X550EM_x) + return IXGBE_ERR_LINK_SETUP; + /* Disable AN and force speed to 10G Serial. */ status = mac->ops.read_iosf_sb_reg(hw, IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), @@ -3070,7 +3139,8 @@ s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw) if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) return IXGBE_ERR_CONFIG; - if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { + if (hw->mac.type == ixgbe_mac_X550EM_x && + !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { /* If link is down, there is no setup necessary so return */ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up); if (status != IXGBE_SUCCESS) @@ -3129,56 +3199,56 @@ s32 ixgbe_setup_phy_loopback_x550em(struct ixgbe_hw *hw) /* Disable AN and force speed to 10G Serial. */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); if (status != IXGBE_SUCCESS) return status; reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE; reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK; reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); if (status != IXGBE_SUCCESS) return status; /* Set near-end loopback clocks. */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); + IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); if (status != IXGBE_SUCCESS) return status; reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_32B; reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_KRPCS; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); if (status != IXGBE_SUCCESS) return status; /* Set loopback enable. */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); + IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); if (status != IXGBE_SUCCESS) return status; reg_val |= IXGBE_KRM_PMD_DFX_BURNIN_TX_RX_KR_LB_MASK; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); if (status != IXGBE_SUCCESS) return status; /* Training bypass. */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); + IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); if (status != IXGBE_SUCCESS) return status; reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_PROTOCOL_BYPASS; status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); return status; } @@ -3192,13 +3262,13 @@ s32 ixgbe_setup_phy_loopback_x550em(struct ixgbe_hw *hw) * * Reads a 16 bit word from the EEPROM using the hostif. **/ -s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset, - u16 *data) +s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, u16 *data) { - s32 status; + const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM; struct ixgbe_hic_read_shadow_ram buffer; + s32 status; - DEBUGFUNC("ixgbe_read_ee_hostif_data_X550"); + DEBUGFUNC("ixgbe_read_ee_hostif_X550"); buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD; buffer.hdr.req.buf_lenh = 0; buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN; @@ -3209,42 +3279,18 @@ s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset, /* one word */ buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16)); - status = ixgbe_host_interface_command(hw, (u32 *)&buffer, - sizeof(buffer), - IXGBE_HI_COMMAND_TIMEOUT, false); - + status = hw->mac.ops.acquire_swfw_sync(hw, mask); if (status) return status; - *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, - FW_NVM_DATA_OFFSET); - - return 0; -} - -/** - * ixgbe_read_ee_hostif_X550 - Read EEPROM word using a host interface command - * @hw: pointer to hardware structure - * @offset: offset of word in the EEPROM to read - * @data: word read from the EEPROM - * - * Reads a 16 bit word from the EEPROM using the hostif. - **/ -s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, - u16 *data) -{ - s32 status = IXGBE_SUCCESS; - - DEBUGFUNC("ixgbe_read_ee_hostif_X550"); - - if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) == - IXGBE_SUCCESS) { - status = ixgbe_read_ee_hostif_data_X550(hw, offset, data); - hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); - } else { - status = IXGBE_ERR_SWFW_SYNC; + status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer), + IXGBE_HI_COMMAND_TIMEOUT); + if (!status) { + *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, + FW_NVM_DATA_OFFSET); } + hw->mac.ops.release_swfw_sync(hw, mask); return status; } @@ -3260,6 +3306,7 @@ s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset, s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw, u16 offset, u16 words, u16 *data) { + const u32 mask = IXGBE_GSSR_SW_MNG_SM | IXGBE_GSSR_EEP_SM; struct ixgbe_hic_read_shadow_ram buffer; u32 current_word = 0; u16 words_to_read; @@ -3269,11 +3316,12 @@ s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw, DEBUGFUNC("ixgbe_read_ee_hostif_buffer_X550"); /* Take semaphore for the entire operation. */ - status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM); + status = hw->mac.ops.acquire_swfw_sync(hw, mask); if (status) { DEBUGOUT("EEPROM read buffer - semaphore failed\n"); return status; } + while (words) { if (words > FW_MAX_READ_BUFFER_SIZE / 2) words_to_read = FW_MAX_READ_BUFFER_SIZE / 2; @@ -3289,10 +3337,8 @@ s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw, buffer.address = IXGBE_CPU_TO_BE32((offset + current_word) * 2); buffer.length = IXGBE_CPU_TO_BE16(words_to_read * 2); - status = ixgbe_host_interface_command(hw, (u32 *)&buffer, - sizeof(buffer), - IXGBE_HI_COMMAND_TIMEOUT, - false); + status = ixgbe_hic_unlocked(hw, (u32 *)&buffer, sizeof(buffer), + IXGBE_HI_COMMAND_TIMEOUT); if (status) { DEBUGOUT("Host interface command failed\n"); @@ -3317,7 +3363,7 @@ s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw, } out: - hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM); + hw->mac.ops.release_swfw_sync(hw, mask); return status; } @@ -3737,6 +3783,14 @@ u32 ixgbe_get_supported_physical_layer_X550em(struct ixgbe_hw *hw) if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY) physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; break; + case ixgbe_phy_fw: + if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_1GB_FULL) + physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; + if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_100_FULL) + physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX; + if (hw->phy.speeds_supported & IXGBE_LINK_SPEED_10_FULL) + physical_layer |= IXGBE_PHYSICAL_LAYER_10BASE_T; + break; default: break; } @@ -4019,19 +4073,19 @@ s32 ixgbe_setup_fc_X550em(struct ixgbe_hw *hw) case IXGBE_DEV_ID_X550EM_A_KR: case IXGBE_DEV_ID_X550EM_A_KR_L: ret_val = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); + IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val); if (ret_val != IXGBE_SUCCESS) goto out; reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE | - IXGBE_KRM_AN_CNTL_1_ASM_PAUSE); + IXGBE_KRM_AN_CNTL_1_ASM_PAUSE); if (pause) reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE; if (asm_dir) reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE; ret_val = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); + IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val); /* This device does not fully support AN. */ hw->fc.disable_fc_autoneg = true; @@ -4064,7 +4118,7 @@ void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw) */ if (hw->fc.disable_fc_autoneg) { ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, - "Flow control autoneg is disabled"); + "Flow control autoneg is disabled"); goto out; } @@ -4076,8 +4130,8 @@ void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw) /* Check at auto-negotiation has completed */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_S1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1); + IXGBE_KRM_LINK_S1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1); if (status != IXGBE_SUCCESS || (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) { @@ -4090,8 +4144,8 @@ void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw) * local flow control settings accordingly */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl_1); + IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl_1); if (status != IXGBE_SUCCESS) { DEBUGOUT("Auto-Negotiation did not complete\n"); @@ -4099,8 +4153,8 @@ void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw) } status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LP_BASE_PAGE_HIGH(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &lp_an_page_low); + IXGBE_KRM_LP_BASE_PAGE_HIGH(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, &lp_an_page_low); if (status != IXGBE_SUCCESS) { DEBUGOUT("Auto-Negotiation did not complete\n"); @@ -4123,80 +4177,14 @@ out: } /** - * ixgbe_fc_autoneg_fiber_x550em_a - Enable flow control IEEE clause 37 + * ixgbe_fc_autoneg_fiber_x550em_a - passthrough FC settings * @hw: pointer to hardware structure * - * Enable flow control according to IEEE clause 37. **/ void ixgbe_fc_autoneg_fiber_x550em_a(struct ixgbe_hw *hw) { - u32 link_s1, pcs_an_lp, pcs_an; - s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED; - ixgbe_link_speed speed; - bool link_up; - - /* AN should have completed when the cable was plugged in. - * Look for reasons to bail out. Bail out if: - * - FC autoneg is disabled, or if - * - link is not up. - */ - if (hw->fc.disable_fc_autoneg) { - ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, - "Flow control autoneg is disabled"); - goto out; - } - - hw->mac.ops.check_link(hw, &speed, &link_up, false); - if (!link_up) { - ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down"); - goto out; - } - - /* Check if auto-negotiation has completed */ - status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_S1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1); - - if (status != IXGBE_SUCCESS || - (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) { - DEBUGOUT("Auto-Negotiation did not complete\n"); - status = IXGBE_ERR_FC_NOT_NEGOTIATED; - goto out; - } - - /* Determine advertised flow control */ - status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_PCS_KX_AN(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &pcs_an); - - if (status != IXGBE_SUCCESS) { - DEBUGOUT("Auto-Negotiation did not complete\n"); - goto out; - } - - /* Determine link parter flow control */ - status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_PCS_KX_AN_LP(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &pcs_an_lp); - - if (status != IXGBE_SUCCESS) { - DEBUGOUT("Auto-Negotiation did not complete\n"); - goto out; - } - - status = ixgbe_negotiate_fc(hw, pcs_an, pcs_an_lp, - IXGBE_KRM_PCS_KX_AN_SYM_PAUSE, - IXGBE_KRM_PCS_KX_AN_ASM_PAUSE, - IXGBE_KRM_PCS_KX_AN_LP_SYM_PAUSE, - IXGBE_KRM_PCS_KX_AN_LP_ASM_PAUSE); - -out: - if (status == IXGBE_SUCCESS) { - hw->fc.fc_was_autonegged = true; - } else { - hw->fc.fc_was_autonegged = false; - hw->fc.current_mode = hw->fc.requested_mode; - } + hw->fc.fc_was_autonegged = false; + hw->fc.current_mode = hw->fc.requested_mode; } /** @@ -4208,9 +4196,10 @@ out: void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw) { s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED; - u16 reg, pcs_an_lp, pcs_an; + u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 }; ixgbe_link_speed speed; bool link_up; + u32 fc; /* AN should have completed when the cable was plugged in. * Look for reasons to bail out. Bail out if: @@ -4230,34 +4219,33 @@ void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw) } /* Check if auto-negotiation has completed */ - status = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_STATUS, - IXGBE_MDIO_ZERO_DEV_TYPE, ®); + status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info); if (status != IXGBE_SUCCESS || - (reg & IXGBE_M88E1500_COPPER_STATUS_AN_DONE) == 0) { + !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) { DEBUGOUT("Auto-Negotiation did not complete\n"); status = IXGBE_ERR_FC_NOT_NEGOTIATED; goto out; } - /* Get the advertized flow control */ - status = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_AN, - IXGBE_MDIO_ZERO_DEV_TYPE, &pcs_an); - if (status != IXGBE_SUCCESS) - goto out; + /* Get the advertized flow control and modify it to indicate + * pause and asymmetric pause instead of rx and tx + */ + fc = info[0]; + if (fc & FW_PHY_ACT_GET_LINK_INFO_FC_RX) + fc ^= FW_PHY_ACT_GET_LINK_INFO_FC_TX; - /* Get link partner's flow control */ - status = hw->phy.ops.read_reg(hw, - IXGBE_M88E1500_COPPER_AN_LP_ABILITY, - IXGBE_MDIO_ZERO_DEV_TYPE, &pcs_an_lp); - if (status != IXGBE_SUCCESS) - goto out; + /* Modify link partner's flow control to indicate pause and + * asymmetric pause instead of rx and tx + */ + if (fc & FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX) + fc ^= FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX; /* Negotiate the flow control */ - status = ixgbe_negotiate_fc(hw, (u32)pcs_an, (u32)pcs_an_lp, - IXGBE_M88E1500_COPPER_AN_PAUSE, - IXGBE_M88E1500_COPPER_AN_AS_PAUSE, - IXGBE_M88E1500_COPPER_AN_LP_PAUSE, - IXGBE_M88E1500_COPPER_AN_LP_AS_PAUSE); + status = ixgbe_negotiate_fc(hw, fc, fc, + FW_PHY_ACT_GET_LINK_INFO_FC_RX, + FW_PHY_ACT_GET_LINK_INFO_FC_TX, + FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX, + FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX); out: if (status == IXGBE_SUCCESS) { @@ -4268,83 +4256,6 @@ out: } } -/** - * ixgbe_setup_fc_sgmii_x550em_a - Set up flow control - * @hw: pointer to hardware structure - * - * Called at init time to set up flow control. - **/ -s32 ixgbe_setup_fc_sgmii_x550em_a(struct ixgbe_hw *hw) -{ - u16 reg; - s32 rc; - - /* Validate the requested mode */ - if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { - ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, - "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); - return IXGBE_ERR_INVALID_LINK_SETTINGS; - } - - if (hw->fc.requested_mode == ixgbe_fc_default) - hw->fc.requested_mode = ixgbe_fc_full; - - /* Read contents of the Auto-Negotiation register, page 0 reg 4 */ - rc = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_AN, - IXGBE_MDIO_ZERO_DEV_TYPE, ®); - if (rc) - goto out; - - /* Disable all the settings related to Flow control Auto-negotiation */ - reg &= ~IXGBE_M88E1500_COPPER_AN_AS_PAUSE; - reg &= ~IXGBE_M88E1500_COPPER_AN_PAUSE; - - /* Configure the Asymmetric and symmetric pause according to the user - * requested mode. - */ - switch (hw->fc.requested_mode) { - case ixgbe_fc_full: - reg |= IXGBE_M88E1500_COPPER_AN_PAUSE; - reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE; - break; - case ixgbe_fc_rx_pause: - reg |= IXGBE_M88E1500_COPPER_AN_PAUSE; - reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE; - break; - case ixgbe_fc_tx_pause: - reg |= IXGBE_M88E1500_COPPER_AN_AS_PAUSE; - break; - default: - break; - } - - /* Write back to the Auto-Negotiation register with newly configured - * fields - */ - hw->phy.ops.write_reg(hw, IXGBE_M88E1500_COPPER_AN, - IXGBE_MDIO_ZERO_DEV_TYPE, reg); - - /* In this section of the code we restart Auto-negotiation */ - - /* Read the CONTROL register, Page 0 reg 0 */ - rc = hw->phy.ops.read_reg(hw, IXGBE_M88E1500_COPPER_CTRL, - IXGBE_MDIO_ZERO_DEV_TYPE, ®); - if (rc) - goto out; - - /* Set the bit to restart Auto-Neg. The bit to enable Auto-neg is ON - * by default - */ - reg |= IXGBE_M88E1500_COPPER_CTRL_RESTART_AN; - - /* write the new values to the register to restart Auto-Negotiation */ - hw->phy.ops.write_reg(hw, IXGBE_M88E1500_COPPER_CTRL, - IXGBE_MDIO_ZERO_DEV_TYPE, reg); - -out: - return rc; -} - /** * ixgbe_setup_fc_backplane_x550em_a - Set up flow control * @hw: pointer to hardware structure @@ -4361,7 +4272,7 @@ s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) /* Validate the requested mode */ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, - "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); + "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); return IXGBE_ERR_INVALID_LINK_SETTINGS; } @@ -4373,8 +4284,8 @@ s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) * we link at 10G, the 1G advertisement is harmless and vice versa. */ status = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl); + IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl); if (status != IXGBE_SUCCESS) { DEBUGOUT("Auto-Negotiation did not complete\n"); @@ -4415,7 +4326,7 @@ s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) case ixgbe_fc_full: /* Flow control (both Rx and Tx) is enabled by SW override. */ an_cntl |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE | - IXGBE_KRM_AN_CNTL_1_ASM_PAUSE; + IXGBE_KRM_AN_CNTL_1_ASM_PAUSE; break; default: ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, @@ -4424,8 +4335,8 @@ s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) } status = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl); + IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id), + IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl); /* Restart auto-negotiation. */ status = ixgbe_restart_an_internal_phy_x550em(hw); @@ -4433,120 +4344,6 @@ s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw) return status; } -/** - * ixgbe_setup_fc_fiber_x550em_a - Set up flow control - * @hw: pointer to hardware structure - * - * Called at init time to set up flow control. - **/ -s32 ixgbe_setup_fc_fiber_x550em_a(struct ixgbe_hw *hw) -{ - struct ixgbe_mac_info *mac = &hw->mac; - s32 rc = IXGBE_SUCCESS; - u32 an_cntl4, lctrl, pcs_an; - - DEBUGFUNC("ixgbe_setup_fc_fiber_x550em_a"); - - /* Validate the requested mode */ - if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) { - ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED, - "ixgbe_fc_rx_pause not valid in strict IEEE mode\n"); - return IXGBE_ERR_INVALID_LINK_SETTINGS; - } - - /* Enable clause 37 auto-negotiation in KRM_LINK_CTRL_1 */ - if (hw->fc.requested_mode == ixgbe_fc_default) - hw->fc.requested_mode = ixgbe_fc_full; - - rc = mac->ops.read_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &lctrl); - if (rc) - return rc; - - lctrl |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE; - lctrl |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_CLAUSE_37_EN; - - rc = mac->ops.write_iosf_sb_reg(hw, - IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, lctrl); - if (rc) - return rc; - - /* Enable clause 37 over 73 in KRM_AN_CNTL_4 */ - rc = mac->ops.read_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_4(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl4); - if (rc) - return rc; - - an_cntl4 |= IXGBE_KRM_AN_CNTL_4_ECSR_AN37_OVER_73; - - rc = mac->ops.write_iosf_sb_reg(hw, - IXGBE_KRM_AN_CNTL_4(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl4); - if (rc) - return rc; - - rc = hw->mac.ops.read_iosf_sb_reg(hw, - IXGBE_KRM_PCS_KX_AN(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, &pcs_an); - - if (rc) - return rc; - - /* The possible values of fc.requested_mode are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but - * we do not support receiving pause frames). - * 3: Both Rx and Tx flow control (symmetric) are enabled. - * other: Invalid. - */ - switch (hw->fc.requested_mode) { - case ixgbe_fc_none: - /* Flow control completely disabled by software override. */ - pcs_an &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE | - IXGBE_KRM_AN_CNTL_1_ASM_PAUSE); - break; - case ixgbe_fc_tx_pause: - /* Tx Flow control is enabled, and Rx Flow control is - * disabled by software override. - */ - pcs_an |= IXGBE_KRM_PCS_KX_AN_ASM_PAUSE; - pcs_an &= ~IXGBE_KRM_PCS_KX_AN_SYM_PAUSE; - break; - case ixgbe_fc_rx_pause: - /* Rx Flow control is enabled and Tx Flow control is - * disabled by software override. Since there really - * isn't a way to advertise that we are capable of RX - * Pause ONLY, we will advertise that we support both - * symmetric and asymmetric Rx PAUSE, as such we fall - * through to the fc_full statement. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - case ixgbe_fc_full: - /* Flow control (both Rx and Tx) is enabled by SW override. */ - pcs_an |= IXGBE_KRM_PCS_KX_AN_SYM_PAUSE | - IXGBE_KRM_PCS_KX_AN_ASM_PAUSE; - break; - default: - ERROR_REPORT1(IXGBE_ERROR_ARGUMENT, - "Flow control param set incorrectly\n"); - return IXGBE_ERR_CONFIG; - } - - rc = hw->mac.ops.write_iosf_sb_reg(hw, - IXGBE_KRM_PCS_KX_AN(hw->bus.lan_id), - IXGBE_SB_IOSF_TARGET_KR_PHY, pcs_an); - - /* Restart auto-negotiation. */ - rc = ixgbe_restart_an_internal_phy_x550em(hw); - - return rc; -} - /** * ixgbe_set_mux - Set mux for port 1 access with CS4227 * @hw: pointer to hardware structure @@ -4675,7 +4472,7 @@ STATIC void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask) * instances. **/ s32 ixgbe_read_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr, - u32 device_type, u16 *phy_data) + u32 device_type, u16 *phy_data) { s32 status; u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM; @@ -4703,7 +4500,7 @@ s32 ixgbe_read_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr, * The PHY Token is needed since the MDIO is shared between to MAC instances. **/ s32 ixgbe_write_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr, - u32 device_type, u16 phy_data) + u32 device_type, u16 phy_data) { s32 status; u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM; @@ -4776,8 +4573,10 @@ s32 ixgbe_setup_mac_link_t_X550em(struct ixgbe_hw *hw, else force_speed = IXGBE_LINK_SPEED_1GB_FULL; - /* If internal link mode is XFI, then setup XFI internal link. */ - if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { + /* If X552 and internal link mode is XFI, then setup XFI internal link. + */ + if (hw->mac.type == ixgbe_mac_X550EM_x && + !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) { status = ixgbe_setup_ixfi_x550em(hw, &force_speed); if (status != IXGBE_SUCCESS) @@ -4800,7 +4599,7 @@ s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed, bool *link_up, bool link_up_wait_to_complete) { u32 status; - u16 autoneg_status; + u16 i, autoneg_status = 0; if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper) return IXGBE_ERR_CONFIG; @@ -4813,21 +4612,18 @@ s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed, return status; /* MAC link is up, so check external PHY link. - * Read this twice back to back to indicate current status. + * X557 PHY. Link status is latching low, and can only be used to detect + * link drop, and not the current status of the link without performing + * back-to-back reads. */ - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, - &autoneg_status); - - if (status != IXGBE_SUCCESS) - return status; - - status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, - IXGBE_MDIO_AUTO_NEG_DEV_TYPE, - &autoneg_status); + for (i = 0; i < 2; i++) { + status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, + IXGBE_MDIO_AUTO_NEG_DEV_TYPE, + &autoneg_status); - if (status != IXGBE_SUCCESS) - return status; + if (status != IXGBE_SUCCESS) + return status; + } /* If external PHY link is not up, then indicate link not up */ if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS)) @@ -4901,3 +4697,63 @@ s32 ixgbe_led_off_t_X550em(struct ixgbe_hw *hw, u32 led_idx) return IXGBE_SUCCESS; } +/** + * ixgbe_set_fw_drv_ver_x550 - Sends driver version to firmware + * @hw: pointer to the HW structure + * @maj: driver version major number + * @min: driver version minor number + * @build: driver version build number + * @sub: driver version sub build number + * @len: length of driver_ver string + * @driver_ver: driver string + * + * Sends driver version number to firmware through the manageability + * block. On success return IXGBE_SUCCESS + * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring + * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails. + **/ +s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min, + u8 build, u8 sub, u16 len, const char *driver_ver) +{ + struct ixgbe_hic_drv_info2 fw_cmd; + s32 ret_val = IXGBE_SUCCESS; + int i; + + DEBUGFUNC("ixgbe_set_fw_drv_ver_x550"); + + if ((len == 0) || (driver_ver == NULL) || + (len > sizeof(fw_cmd.driver_string))) + return IXGBE_ERR_INVALID_ARGUMENT; + + fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO; + fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN + len; + fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED; + fw_cmd.port_num = (u8)hw->bus.func; + fw_cmd.ver_maj = maj; + fw_cmd.ver_min = min; + fw_cmd.ver_build = build; + fw_cmd.ver_sub = sub; + fw_cmd.hdr.checksum = 0; + memcpy(fw_cmd.driver_string, driver_ver, len); + fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd, + (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len)); + + for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) { + ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd, + sizeof(fw_cmd), + IXGBE_HI_COMMAND_TIMEOUT, + true); + if (ret_val != IXGBE_SUCCESS) + continue; + + if (fw_cmd.hdr.cmd_or_resp.ret_status == + FW_CEM_RESP_STATUS_SUCCESS) + ret_val = IXGBE_SUCCESS; + else + ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND; + + break; + } + + return ret_val; +}