From: Bing Zhao Date: Thu, 15 Oct 2020 13:08:55 +0000 (+0800) Subject: app/testpmd: change hairpin queues setup X-Git-Url: http://git.droids-corp.org/?a=commitdiff_plain;h=01817b10d27c;p=dpdk.git app/testpmd: change hairpin queues setup A new parameter `hairpin-mode` is introduced to the testpmd command line. Bitmask value is used to provide a more flexible configuration. This parameter should be used when `hairpinq` is specified in the command line. Bit 0 in the LSB indicates the hairpin will use the loop mode. The previous port Rx queue will be connected to the current port Tx queue. Bit 1 in the LSB indicates the hairpin will use pair port mode. The even index port will be paired with the next odd index port. If the total number of the probed ports is odd, then the last one will be paired to itself. If this byte is zero, then each port will be paired to itself. Bit 0 takes a higher priority in the checking. Bit 4 in the second bytes indicate if the hairpin will use explicit Tx flow mode. e.g. in the command line, "--hairpinq=2 --hairpin-mode=0x11" If not set, default value zero will be used and the behavior will try to get aligned with the previous single port mode. If the ports belong to different vendors' NICs, it is suggested to use the `self` hairpin mode only. Since hairpin configures the hardware resources, the port mask of packets forwarding engine will not be used here. Signed-off-by: Bing Zhao Acked-by: Ori Kam --- diff --git a/app/test-pmd/parameters.c b/app/test-pmd/parameters.c index 15ce8c142b..a391f87891 100644 --- a/app/test-pmd/parameters.c +++ b/app/test-pmd/parameters.c @@ -222,6 +222,9 @@ usage(char* progname) "enabled\n"); printf(" --record-core-cycles: enable measurement of CPU cycles.\n"); printf(" --record-burst-stats: enable display of RX and TX bursts.\n"); + printf(" --hairpin-mode=0xXX: bitmask set the hairpin port mode.\n " + " 0x10 - explicit Tx rule, 0x02 - hairpin ports paired\n" + " 0x01 - hairpin ports loop, 0x00 - hairpin port self\n"); } #ifdef RTE_LIBRTE_CMDLINE @@ -645,6 +648,7 @@ launch_args_parse(int argc, char** argv) { "rxd", 1, 0, 0 }, { "txd", 1, 0, 0 }, { "hairpinq", 1, 0, 0 }, + { "hairpin-mode", 1, 0, 0 }, { "burst", 1, 0, 0 }, { "mbcache", 1, 0, 0 }, { "txpt", 1, 0, 0 }, @@ -1113,6 +1117,17 @@ launch_args_parse(int argc, char** argv) rte_exit(EXIT_FAILURE, "Either rx or tx queues should " "be non-zero\n"); } + if (!strcmp(lgopts[opt_idx].name, "hairpin-mode")) { + char *end = NULL; + unsigned int n; + + errno = 0; + n = strtoul(optarg, &end, 0); + if (errno != 0 || end == optarg) + rte_exit(EXIT_FAILURE, "hairpin mode invalid\n"); + else + hairpin_mode = (uint16_t)n; + } if (!strcmp(lgopts[opt_idx].name, "burst")) { n = atoi(optarg); if (n == 0) { diff --git a/app/test-pmd/testpmd.c b/app/test-pmd/testpmd.c index ccba71c076..6caba60988 100644 --- a/app/test-pmd/testpmd.c +++ b/app/test-pmd/testpmd.c @@ -367,6 +367,9 @@ bool setup_on_probe_event = true; /* Clear ptypes on port initialization. */ uint8_t clear_ptypes = true; +/* Hairpin ports configuration mode. */ +uint16_t hairpin_mode; + /* Pretty printing of ethdev events */ static const char * const eth_event_desc[] = { [RTE_ETH_EVENT_UNKNOWN] = "unknown", @@ -2345,7 +2348,7 @@ port_is_started(portid_t port_id) /* Configure the Rx and Tx hairpin queues for the selected port. */ static int -setup_hairpin_queues(portid_t pi) +setup_hairpin_queues(portid_t pi, portid_t p_pi, uint16_t cnt_pi) { queueid_t qi; struct rte_eth_hairpin_conf hairpin_conf = { @@ -2354,10 +2357,49 @@ setup_hairpin_queues(portid_t pi) int i; int diag; struct rte_port *port = &ports[pi]; + uint16_t peer_rx_port = pi; + uint16_t peer_tx_port = pi; + uint32_t manual = 1; + uint32_t tx_exp = hairpin_mode & 0x10; + + if (!(hairpin_mode & 0xf)) { + peer_rx_port = pi; + peer_tx_port = pi; + manual = 0; + } else if (hairpin_mode & 0x1) { + peer_tx_port = rte_eth_find_next_owned_by(pi + 1, + RTE_ETH_DEV_NO_OWNER); + if (peer_tx_port >= RTE_MAX_ETHPORTS) + peer_tx_port = rte_eth_find_next_owned_by(0, + RTE_ETH_DEV_NO_OWNER); + if (p_pi != RTE_MAX_ETHPORTS) { + peer_rx_port = p_pi; + } else { + uint16_t next_pi; + + /* Last port will be the peer RX port of the first. */ + RTE_ETH_FOREACH_DEV(next_pi) + peer_rx_port = next_pi; + } + manual = 1; + } else if (hairpin_mode & 0x2) { + if (cnt_pi & 0x1) { + peer_rx_port = p_pi; + } else { + peer_rx_port = rte_eth_find_next_owned_by(pi + 1, + RTE_ETH_DEV_NO_OWNER); + if (peer_rx_port >= RTE_MAX_ETHPORTS) + peer_rx_port = pi; + } + peer_tx_port = peer_rx_port; + manual = 1; + } for (qi = nb_txq, i = 0; qi < nb_hairpinq + nb_txq; qi++) { - hairpin_conf.peers[0].port = pi; + hairpin_conf.peers[0].port = peer_rx_port; hairpin_conf.peers[0].queue = i + nb_rxq; + hairpin_conf.manual_bind = !!manual; + hairpin_conf.tx_explicit = !!tx_exp; diag = rte_eth_tx_hairpin_queue_setup (pi, qi, nb_txd, &hairpin_conf); i++; @@ -2377,8 +2419,10 @@ setup_hairpin_queues(portid_t pi) return -1; } for (qi = nb_rxq, i = 0; qi < nb_hairpinq + nb_rxq; qi++) { - hairpin_conf.peers[0].port = pi; + hairpin_conf.peers[0].port = peer_tx_port; hairpin_conf.peers[0].queue = i + nb_txq; + hairpin_conf.manual_bind = !!manual; + hairpin_conf.tx_explicit = !!tx_exp; diag = rte_eth_rx_hairpin_queue_setup (pi, qi, nb_rxd, &hairpin_conf); i++; @@ -2405,6 +2449,12 @@ start_port(portid_t pid) { int diag, need_check_link_status = -1; portid_t pi; + portid_t p_pi = RTE_MAX_ETHPORTS; + portid_t pl[RTE_MAX_ETHPORTS]; + portid_t peer_pl[RTE_MAX_ETHPORTS]; + uint16_t cnt_pi = 0; + uint16_t cfg_pi = 0; + int peer_pi; queueid_t qi; struct rte_port *port; struct rte_ether_addr mac_addr; @@ -2544,7 +2594,7 @@ start_port(portid_t pid) return -1; } /* setup hairpin queues */ - if (setup_hairpin_queues(pi) != 0) + if (setup_hairpin_queues(pi, p_pi, cnt_pi) != 0) return -1; } configure_rxtx_dump_callbacks(verbose_level); @@ -2557,6 +2607,9 @@ start_port(portid_t pid) pi); } + p_pi = pi; + cnt_pi++; + /* start port */ if (rte_eth_dev_start(pi) < 0) { printf("Fail to start port %d\n", pi); @@ -2581,6 +2634,8 @@ start_port(portid_t pid) /* at least one port started, need checking link status */ need_check_link_status = 1; + + pl[cfg_pi++] = pi; } if (need_check_link_status == 1 && !no_link_check) @@ -2588,6 +2643,50 @@ start_port(portid_t pid) else if (need_check_link_status == 0) printf("Please stop the ports first\n"); + if (hairpin_mode & 0xf) { + uint16_t i; + int j; + + /* bind all started hairpin ports */ + for (i = 0; i < cfg_pi; i++) { + pi = pl[i]; + /* bind current Tx to all peer Rx */ + peer_pi = rte_eth_hairpin_get_peer_ports(pi, peer_pl, + RTE_MAX_ETHPORTS, 1); + if (peer_pi < 0) + return peer_pi; + for (j = 0; j < peer_pi; j++) { + if (!port_is_started(peer_pl[j])) + continue; + diag = rte_eth_hairpin_bind(pi, peer_pl[j]); + if (diag < 0) { + printf("Error during binding hairpin" + " Tx port %u to %u: %s\n", + pi, peer_pl[j], + rte_strerror(-diag)); + return -1; + } + } + /* bind all peer Tx to current Rx */ + peer_pi = rte_eth_hairpin_get_peer_ports(pi, peer_pl, + RTE_MAX_ETHPORTS, 0); + if (peer_pi < 0) + return peer_pi; + for (j = 0; j < peer_pi; j++) { + if (!port_is_started(peer_pl[j])) + continue; + diag = rte_eth_hairpin_bind(peer_pl[j], pi); + if (diag < 0) { + printf("Error during binding hairpin" + " Tx port %u to %u: %s\n", + peer_pl[j], pi, + rte_strerror(-diag)); + return -1; + } + } + } + } + printf("Done\n"); return 0; } @@ -2598,6 +2697,8 @@ stop_port(portid_t pid) portid_t pi; struct rte_port *port; int need_check_link_status = 0; + portid_t peer_pl[RTE_MAX_ETHPORTS]; + int peer_pi; if (dcb_test) { dcb_test = 0; @@ -2628,6 +2729,22 @@ stop_port(portid_t pid) RTE_PORT_HANDLING) == 0) continue; + if (hairpin_mode & 0xf) { + int j; + + rte_eth_hairpin_unbind(pi, RTE_MAX_ETHPORTS); + /* unbind all peer Tx from current Rx */ + peer_pi = rte_eth_hairpin_get_peer_ports(pi, peer_pl, + RTE_MAX_ETHPORTS, 0); + if (peer_pi < 0) + continue; + for (j = 0; j < peer_pi; j++) { + if (!port_is_started(peer_pl[j])) + continue; + rte_eth_hairpin_unbind(peer_pl[j], pi); + } + } + rte_eth_dev_stop(pi); if (rte_atomic16_cmpset(&(port->port_status), diff --git a/app/test-pmd/testpmd.h b/app/test-pmd/testpmd.h index a4dfd4fc23..f8b0a3517d 100644 --- a/app/test-pmd/testpmd.h +++ b/app/test-pmd/testpmd.h @@ -408,6 +408,8 @@ extern uint32_t param_total_num_mbufs; extern uint16_t stats_period; +extern uint16_t hairpin_mode; + #ifdef RTE_LIBRTE_LATENCY_STATS extern uint8_t latencystats_enabled; extern lcoreid_t latencystats_lcore_id; diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst index ec085c298f..d3ee59deae 100644 --- a/doc/guides/testpmd_app_ug/run_app.rst +++ b/doc/guides/testpmd_app_ug/run_app.rst @@ -503,3 +503,11 @@ The command line options are: * ``--record-burst-stats`` Enable display of RX and TX burst stats. + +* ``--hairpin-mode=0xXX`` + + Set the hairpin port mode with bitmask, only valid when hairpin queues number is set. + bit 4 - explicit Tx flow rule + bit 1 - two hairpin ports paired + bit 0 - two hairpin ports loop + The default value is 0. Hairpin will use single port mode and implicit Tx flow mode.