From: Alexander Kozyrev Date: Thu, 9 Apr 2020 22:23:51 +0000 (+0000) Subject: net/mlx5: add device parameter for MPRQ stride size X-Git-Url: http://git.droids-corp.org/?a=commitdiff_plain;h=ecb160456aed51ccf69dc96cb835c259d611d276;p=dpdk.git net/mlx5: add device parameter for MPRQ stride size Define a device parameter to configure log 2 of a stride size for MPRQ - mprq_log_stride_size. User is able to specify a stride size in a range allowed by an underlying hardware. The default stride size is defined as 2048 bytes to encompass most commonly used packet sizes in the Internet (MTU 1518 and less) and will be used in case a maximum configured packet size cannot fit into the largest possible stride size. Otherwise a stride size is set to a large enough value to encompass a whole packet. Cc: stable@dpdk.org Signed-off-by: Alexander Kozyrev Acked-by: Viacheslav Ovsiienko Acked-by: Matan Azrad --- diff --git a/doc/guides/nics/mlx5.rst b/doc/guides/nics/mlx5.rst index ca4ded2f22..34c18b7f19 100644 --- a/doc/guides/nics/mlx5.rst +++ b/doc/guides/nics/mlx5.rst @@ -408,8 +408,7 @@ Run-time configuration A nonzero value enables configuring Multi-Packet Rx queues. Rx queue is configured as Multi-Packet RQ if the total number of Rx queues is - ``rxqs_min_mprq`` or more and Rx scatter isn't configured. Disabled by - default. + ``rxqs_min_mprq`` or more. Disabled by default. Multi-Packet Rx Queue (MPRQ a.k.a Striding RQ) can further save PCIe bandwidth by posting a single large buffer for multiple packets. Instead of posting a @@ -434,6 +433,20 @@ Run-time configuration The size of Rx queue should be bigger than the number of strides. +- ``mprq_log_stride_size`` parameter [int] + + Log 2 of the size of a stride for Multi-Packet Rx queue. Configuring a smaller + stride size can save some memory and reduce probability of a depletion of all + available strides due to unreleased packets by an application. If configured + value is not in the range of device capability, the default value will be set + with a warning message. The default value is 11 which is 2048 bytes per a + stride, valid only if ``mprq_en`` is set. With ``mprq_log_stride_size`` set + it is possible for a pcaket to span across multiple strides. This mode allows + support of jumbo frames (9K) with MPRQ. The memcopy of some packets (or part + of a packet if Rx scatter is configured) may be required in case there is no + space left for a head room at the end of a stride which incurs some + performance penalty. + - ``mprq_max_memcpy_len`` parameter [int] The maximum length of packet to memcpy in case of Multi-Packet Rx queue. Rx diff --git a/doc/guides/rel_notes/release_20_05.rst b/doc/guides/rel_notes/release_20_05.rst index 2cc583610b..31b5b992d1 100644 --- a/doc/guides/rel_notes/release_20_05.rst +++ b/doc/guides/rel_notes/release_20_05.rst @@ -126,6 +126,7 @@ New Features * Added support for matching on IPv4 Time To Live and IPv6 Hop Limit. * Added support for creating Relaxed Ordering Memory Regions. + * Added support for jumbo frame size (9K MTU) in Multi-Packet RQ mode. * **Updated the AESNI MB crypto PMD.** diff --git a/drivers/net/mlx5/mlx5.c b/drivers/net/mlx5/mlx5.c index efdd53cc5c..293d316413 100644 --- a/drivers/net/mlx5/mlx5.c +++ b/drivers/net/mlx5/mlx5.c @@ -63,6 +63,9 @@ /* Device parameter to configure log 2 of the number of strides for MPRQ. */ #define MLX5_RX_MPRQ_LOG_STRIDE_NUM "mprq_log_stride_num" +/* Device parameter to configure log 2 of the stride size for MPRQ. */ +#define MLX5_RX_MPRQ_LOG_STRIDE_SIZE "mprq_log_stride_size" + /* Device parameter to limit the size of memcpy'd packet for MPRQ. */ #define MLX5_RX_MPRQ_MAX_MEMCPY_LEN "mprq_max_memcpy_len" @@ -1533,6 +1536,8 @@ mlx5_args_check(const char *key, const char *val, void *opaque) config->mprq.enabled = !!tmp; } else if (strcmp(MLX5_RX_MPRQ_LOG_STRIDE_NUM, key) == 0) { config->mprq.stride_num_n = tmp; + } else if (strcmp(MLX5_RX_MPRQ_LOG_STRIDE_SIZE, key) == 0) { + config->mprq.stride_size_n = tmp; } else if (strcmp(MLX5_RX_MPRQ_MAX_MEMCPY_LEN, key) == 0) { config->mprq.max_memcpy_len = tmp; } else if (strcmp(MLX5_RXQS_MIN_MPRQ, key) == 0) { @@ -1629,6 +1634,7 @@ mlx5_args(struct mlx5_dev_config *config, struct rte_devargs *devargs) MLX5_RXQ_PKT_PAD_EN, MLX5_RX_MPRQ_EN, MLX5_RX_MPRQ_LOG_STRIDE_NUM, + MLX5_RX_MPRQ_LOG_STRIDE_SIZE, MLX5_RX_MPRQ_MAX_MEMCPY_LEN, MLX5_RXQS_MIN_MPRQ, MLX5_TXQ_INLINE, @@ -2304,8 +2310,6 @@ mlx5_dev_spawn(struct rte_device *dpdk_dev, mprq_caps.min_single_wqe_log_num_of_strides; mprq_max_stride_num_n = mprq_caps.max_single_wqe_log_num_of_strides; - config.mprq.stride_num_n = RTE_MAX(MLX5_MPRQ_STRIDE_NUM_N, - mprq_min_stride_num_n); } #endif if (RTE_CACHE_LINE_SIZE == 128 && @@ -2619,17 +2623,32 @@ mlx5_dev_spawn(struct rte_device *dpdk_dev, #endif } if (config.mprq.enabled && mprq) { - if (config.mprq.stride_num_n > mprq_max_stride_num_n || - config.mprq.stride_num_n < mprq_min_stride_num_n) { + if (config.mprq.stride_num_n && + (config.mprq.stride_num_n > mprq_max_stride_num_n || + config.mprq.stride_num_n < mprq_min_stride_num_n)) { config.mprq.stride_num_n = - RTE_MAX(MLX5_MPRQ_STRIDE_NUM_N, - mprq_min_stride_num_n); + RTE_MIN(RTE_MAX(MLX5_MPRQ_STRIDE_NUM_N, + mprq_min_stride_num_n), + mprq_max_stride_num_n); DRV_LOG(WARNING, "the number of strides" " for Multi-Packet RQ is out of range," " setting default value (%u)", 1 << config.mprq.stride_num_n); } + if (config.mprq.stride_size_n && + (config.mprq.stride_size_n > mprq_max_stride_size_n || + config.mprq.stride_size_n < mprq_min_stride_size_n)) { + config.mprq.stride_size_n = + RTE_MIN(RTE_MAX(MLX5_MPRQ_STRIDE_SIZE_N, + mprq_min_stride_size_n), + mprq_max_stride_size_n); + DRV_LOG(WARNING, + "the size of a stride" + " for Multi-Packet RQ is out of range," + " setting default value (%u)", + 1 << config.mprq.stride_size_n); + } config.mprq.min_stride_size_n = mprq_min_stride_size_n; config.mprq.max_stride_size_n = mprq_max_stride_size_n; } else if (config.mprq.enabled && !mprq) { @@ -3363,7 +3382,8 @@ mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused, .mr_ext_memseg_en = 1, .mprq = { .enabled = 0, /* Disabled by default. */ - .stride_num_n = MLX5_MPRQ_STRIDE_NUM_N, + .stride_num_n = 0, + .stride_size_n = 0, .max_memcpy_len = MLX5_MPRQ_MEMCPY_DEFAULT_LEN, .min_rxqs_num = MLX5_MPRQ_MIN_RXQS, }, diff --git a/drivers/net/mlx5/mlx5.h b/drivers/net/mlx5/mlx5.h index 45619dcfff..94178e7ae7 100644 --- a/drivers/net/mlx5/mlx5.h +++ b/drivers/net/mlx5/mlx5.h @@ -179,6 +179,7 @@ struct mlx5_dev_config { struct { unsigned int enabled:1; /* Whether MPRQ is enabled. */ unsigned int stride_num_n; /* Number of strides. */ + unsigned int stride_size_n; /* Size of a stride. */ unsigned int min_stride_size_n; /* Min size of a stride. */ unsigned int max_stride_size_n; /* Max size of a stride. */ unsigned int max_memcpy_len; diff --git a/drivers/net/mlx5/mlx5_defs.h b/drivers/net/mlx5/mlx5_defs.h index 19e8253d57..260f584298 100644 --- a/drivers/net/mlx5/mlx5_defs.h +++ b/drivers/net/mlx5/mlx5_defs.h @@ -143,6 +143,9 @@ /* Log 2 of the default number of strides per WQE for Multi-Packet RQ. */ #define MLX5_MPRQ_STRIDE_NUM_N 6U +/* Log 2 of the default size of a stride per WQE for Multi-Packet RQ. */ +#define MLX5_MPRQ_STRIDE_SIZE_N 11U + /* Two-byte shift is disabled for Multi-Packet RQ. */ #define MLX5_MPRQ_TWO_BYTE_SHIFT 0 diff --git a/drivers/net/mlx5/mlx5_rxq.c b/drivers/net/mlx5/mlx5_rxq.c index 0a95e3c753..1b57f00cb2 100644 --- a/drivers/net/mlx5/mlx5_rxq.c +++ b/drivers/net/mlx5/mlx5_rxq.c @@ -1793,7 +1793,9 @@ mlx5_rxq_new(struct rte_eth_dev *dev, uint16_t idx, uint16_t desc, struct mlx5_priv *priv = dev->data->dev_private; struct mlx5_rxq_ctrl *tmpl; unsigned int mb_len = rte_pktmbuf_data_room_size(mp); + unsigned int mprq_stride_nums; unsigned int mprq_stride_size; + unsigned int mprq_stride_cap; struct mlx5_dev_config *config = &priv->config; unsigned int strd_headroom_en; /* @@ -1856,25 +1858,40 @@ mlx5_rxq_new(struct rte_eth_dev *dev, uint16_t idx, uint16_t desc, strd_headroom_en = 1; mprq_stride_size = non_scatter_min_mbuf_size; } + mprq_stride_nums = config->mprq.stride_num_n ? + config->mprq.stride_num_n : MLX5_MPRQ_STRIDE_NUM_N; + mprq_stride_size = (mprq_stride_size <= + (1U << config->mprq.max_stride_size_n)) ? + log2above(mprq_stride_size) : MLX5_MPRQ_STRIDE_SIZE_N; + mprq_stride_cap = (config->mprq.stride_num_n ? + (1U << config->mprq.stride_num_n) : (1U << mprq_stride_nums)) * + (config->mprq.stride_size_n ? + (1U << config->mprq.stride_size_n) : (1U << mprq_stride_size)); /* * This Rx queue can be configured as a Multi-Packet RQ if all of the * following conditions are met: * - MPRQ is enabled. * - The number of descs is more than the number of strides. - * - max_rx_pkt_len plus overhead is less than the max size of a - * stride. + * - max_rx_pkt_len plus overhead is less than the max size + * of a stride or mprq_stride_size is specified by a user. + * Need to nake sure that there are enough stides to encap + * the maximum packet size in case mprq_stride_size is set. * Otherwise, enable Rx scatter if necessary. */ - if (mprq_en && - desc > (1U << config->mprq.stride_num_n) && - mprq_stride_size <= (1U << config->mprq.max_stride_size_n)) { + if (mprq_en && desc > (1U << mprq_stride_nums) && + (non_scatter_min_mbuf_size - + (lro_on_queue ? RTE_PKTMBUF_HEADROOM : 0) <= + (1U << config->mprq.max_stride_size_n) || + (config->mprq.stride_size_n && + non_scatter_min_mbuf_size <= mprq_stride_cap))) { /* TODO: Rx scatter isn't supported yet. */ tmpl->rxq.sges_n = 0; /* Trim the number of descs needed. */ - desc >>= config->mprq.stride_num_n; - tmpl->rxq.strd_num_n = config->mprq.stride_num_n; - tmpl->rxq.strd_sz_n = RTE_MAX(log2above(mprq_stride_size), - config->mprq.min_stride_size_n); + desc >>= mprq_stride_nums; + tmpl->rxq.strd_num_n = config->mprq.stride_num_n ? + config->mprq.stride_num_n : mprq_stride_nums; + tmpl->rxq.strd_sz_n = config->mprq.stride_size_n ? + config->mprq.stride_size_n : mprq_stride_size; tmpl->rxq.strd_shift_en = MLX5_MPRQ_TWO_BYTE_SHIFT; tmpl->rxq.strd_headroom_en = strd_headroom_en; tmpl->rxq.mprq_max_memcpy_len = RTE_MIN(first_mb_free_size, @@ -1923,11 +1940,18 @@ mlx5_rxq_new(struct rte_eth_dev *dev, uint16_t idx, uint16_t desc, if (mprq_en && !mlx5_rxq_mprq_enabled(&tmpl->rxq)) DRV_LOG(WARNING, "port %u MPRQ is requested but cannot be enabled" - " (requested: desc = %u, stride_sz = %u," - " supported: min_stride_num = %u, max_stride_sz = %u).", - dev->data->port_id, desc, mprq_stride_size, - (1 << config->mprq.stride_num_n), - (1 << config->mprq.max_stride_size_n)); + " (requested: packet size = %u, desc = %u," + " stride_sz = %u, stride_num = %u," + " supported: min_stride_sz = %u, max_stride_sz = %u).", + dev->data->port_id, non_scatter_min_mbuf_size, desc, + config->mprq.stride_size_n ? + (1U << config->mprq.stride_size_n) : + (1U << mprq_stride_size), + config->mprq.stride_num_n ? + (1U << config->mprq.stride_num_n) : + (1U << mprq_stride_nums), + (1U << config->mprq.min_stride_size_n), + (1U << config->mprq.max_stride_size_n)); DRV_LOG(DEBUG, "port %u maximum number of segments per packet: %u", dev->data->port_id, 1 << tmpl->rxq.sges_n); if (desc % (1 << tmpl->rxq.sges_n)) {