From 5c7cb08888cef019a181cb796a786da96701c3cc Mon Sep 17 00:00:00 2001 From: Ciara Power Date: Mon, 21 Sep 2020 14:59:14 +0100 Subject: [PATCH] doc: remove references to make from Linux guide Make is no longer supported for compiling DPDK, references are now removed in the documentation. Signed-off-by: Ciara Power Reviewed-by: Bruce Richardson --- doc/guides/linux_gsg/build_dpdk.rst | 6 +++++- doc/guides/linux_gsg/build_sample_apps.rst | 20 ++++---------------- doc/guides/linux_gsg/enable_func.rst | 13 ++++++------- doc/guides/linux_gsg/linux_drivers.rst | 14 ++++++++------ doc/guides/linux_gsg/sys_reqs.rst | 6 +----- 5 files changed, 24 insertions(+), 35 deletions(-) diff --git a/doc/guides/linux_gsg/build_dpdk.rst b/doc/guides/linux_gsg/build_dpdk.rst index a895e1b0f4..1d867dedf6 100644 --- a/doc/guides/linux_gsg/build_dpdk.rst +++ b/doc/guides/linux_gsg/build_dpdk.rst @@ -76,6 +76,7 @@ and the last step causing the dynamic loader `ld.so` to update its cache to take distributions, `/usr/local/lib` and `/usr/local/lib64` should be added to a file in `/etc/ld.so.conf.d/` before running `ldconfig`. +.. _adjusting_build_options: Adjusting Build Options ~~~~~~~~~~~~~~~~~~~~~~~ @@ -112,6 +113,8 @@ dependencies are met on the current system are built. When `-Dexamples=all` is set as a meson option, meson will check each example application to see if it can be built, and add all which can be built to the list of tasks in the ninja build configuration file. +.. _building_app_using_installed_dpdk: + Building Applications Using Installed DPDK ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ @@ -135,7 +138,8 @@ and the sources for that build are stored in ``$(SRCS-y)``. .. note:: - Unlike with the older make build system, the meson system is not + Unlike with the make build system present in older DPDK releases, + the meson system is not designed to be used directly from a build directory. Instead it is recommended that it be installed either system-wide or to a known location in the user's home directory. The install location can be set diff --git a/doc/guides/linux_gsg/build_sample_apps.rst b/doc/guides/linux_gsg/build_sample_apps.rst index 2882883f95..542246df68 100644 --- a/doc/guides/linux_gsg/build_sample_apps.rst +++ b/doc/guides/linux_gsg/build_sample_apps.rst @@ -1,8 +1,8 @@ .. SPDX-License-Identifier: BSD-3-Clause Copyright(c) 2010-2014 Intel Corporation. -Compiling and Running Sample Applications -========================================= +Running Sample Applications +=========================== The chapter describes how to compile and run applications in an DPDK environment. It also provides a pointer to where sample applications are stored. @@ -119,7 +119,7 @@ Copy the DPDK application binary to your target, then run the application as fol (assuming the platform has four memory channels per processor socket, and that cores 0-3 are present and are to be used for running the application):: - ./helloworld -l 0-3 -n 4 + ./dpdk-helloworld -l 0-3 -n 4 .. note:: @@ -183,19 +183,7 @@ If the DPDK cannot allocate enough memory on each socket, the EAL initialization Additional Sample Applications ------------------------------ -Additional sample applications are included in the ${RTE_SDK}/examples directory. +Additional sample applications are included in the DPDK examples directory. These sample applications may be built and run in a manner similar to that described in earlier sections in this manual. In addition, see the *DPDK Sample Applications User Guide* for a description of the application, specific instructions on compilation and execution and some explanation of the code. - -Additional Test Applications ----------------------------- - -In addition, there are two other applications that are built when the libraries are created. -The source files for these are in the DPDK/app directory and are called test and testpmd. -Once the libraries are created, they can be found in the build/app directory. - -* The test application provides a variety of specific tests for the various functions in the DPDK. - -* The testpmd application provides a number of different packet throughput tests and - examples of features such as how to use the Flow Director found in the Intel® 82599 10 Gigabit Ethernet Controller. diff --git a/doc/guides/linux_gsg/enable_func.rst b/doc/guides/linux_gsg/enable_func.rst index b2bda80bb7..06c17e4058 100644 --- a/doc/guides/linux_gsg/enable_func.rst +++ b/doc/guides/linux_gsg/enable_func.rst @@ -41,7 +41,9 @@ Enabling HPET in the DPDK ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ By default, HPET support is disabled in the DPDK build configuration files. -To use HPET, the ``CONFIG_RTE_LIBEAL_USE_HPET`` setting should be changed to ``y``, which will enable the HPET settings at compile time. +To use HPET, use the following meson build option which will enable the HPET settings at compile time:: + + meson configure -Duse_hpet=true For an application to use the ``rte_get_hpet_cycles()`` and ``rte_get_hpet_hz()`` API calls, and optionally to make the HPET the default time source for the rte_timer library, @@ -128,13 +130,10 @@ Loading the DPDK KNI Kernel Module ---------------------------------- To run the DPDK Kernel NIC Interface (KNI) sample application, an extra kernel module (the kni module) must be loaded into the running kernel. -The module is found in the kmod sub-directory of the DPDK target directory. -Similar to the loading of the ``igb_uio`` module, this module should be loaded using the insmod command as shown below -(assuming that the current directory is the DPDK target directory): - -.. code-block:: console +The module is found in the kernel/linux sub-directory of the DPDK build directory. +It should be loaded using the insmod command:: - insmod kmod/rte_kni.ko + insmod /kernel/linux/kni/rte_kni.ko .. note:: diff --git a/doc/guides/linux_gsg/linux_drivers.rst b/doc/guides/linux_gsg/linux_drivers.rst index 185074013a..7789c572bb 100644 --- a/doc/guides/linux_gsg/linux_drivers.rst +++ b/doc/guides/linux_gsg/linux_drivers.rst @@ -28,18 +28,20 @@ can provide the uio capability. This module can be loaded using the command: ``uio_pci_generic`` module doesn't support the creation of virtual functions. As an alternative to the ``uio_pci_generic``, the DPDK also includes the igb_uio -module which can be found in the kmod subdirectory referred to above. It can +module which can be found in the kernel/linux subdirectory referred to above. It can be loaded as shown below: .. code-block:: console sudo modprobe uio - sudo insmod kmod/igb_uio.ko + sudo insmod /kernel/linux/igb_uio/igb_uio.ko .. note:: - ``igb_uio`` module is disabled by default starting from ``DPDK v20.02``. - To build it, the config option ``CONFIG_RTE_EAL_IGB_UIO`` should be enabled. + Building DPDK Linux kernel modules is disabled by default starting from DPDK 20.02. + To enable them again, the config option "enable_kmods" needs to be set + in the meson build configuration. + See :ref:`adjusting_build_options` for details on how to set/clear build options. It is planned to move ``igb_uio`` module to a different git repository. .. note:: @@ -104,11 +106,11 @@ parameter ``--vfio-vf-token``. 3. echo 2 > /sys/bus/pci/devices/0000:86:00.0/sriov_numvfs 4. Start the PF: - ./x86_64-native-linux-gcc/app/testpmd -l 22-25 -n 4 -w 86:00.0 \ + /app/dpdk-testpmd -l 22-25 -n 4 -w 86:00.0 \ --vfio-vf-token=14d63f20-8445-11ea-8900-1f9ce7d5650d --file-prefix=pf -- -i 5. Start the VF: - ./x86_64-native-linux-gcc/app/testpmd -l 26-29 -n 4 -w 86:02.0 \ + /app/dpdk-testpmd -l 26-29 -n 4 -w 86:02.0 \ --vfio-vf-token=14d63f20-8445-11ea-8900-1f9ce7d5650d --file-prefix=vf0 -- -i Also, to use VFIO, both kernel and BIOS must support and be configured to use IO virtualization (such as Intel® VT-d). diff --git a/doc/guides/linux_gsg/sys_reqs.rst b/doc/guides/linux_gsg/sys_reqs.rst index 6b9f573fce..6ecdc04aa9 100644 --- a/doc/guides/linux_gsg/sys_reqs.rst +++ b/doc/guides/linux_gsg/sys_reqs.rst @@ -43,11 +43,7 @@ Compilation of the DPDK * For Ubuntu/Debian systems these can be installed using ``apt install build-essential`` -* Python, recommended version 3.5+. - - * Python v3.5+ is needed to build DPDK using meson and ninja - - * Python 2.7+ or 3.2+, to use various helper scripts included in the DPDK package. +* Python 3.5 or later. * Meson (version 0.47.1+) and ninja -- 2.20.1