+Quick Start Guide
+-----------------
+
+1. Download latest Mellanox OFED. For more info check the `prerequisites`_.
+
+2. Install the required libraries and kernel modules either by installing
+ only the required set, or by installing the entire Mellanox OFED:
+
+ For bare metal use:
+
+ .. code-block:: console
+
+ ./mlnxofedinstall
+
+ For SR-IOV hypervisors use:
+
+ .. code-block:: console
+
+ ./mlnxofedinstall --enable-sriov -hypervisor
+
+ For SR-IOV virtual machine use:
+
+ .. code-block:: console
+
+ ./mlnxofedinstall --guest
+
+3. Verify the firmware is the correct one:
+
+ .. code-block:: console
+
+ ibv_devinfo
+
+4. Set all ports links to Ethernet, follow instructions on the screen:
+
+ .. code-block:: console
+
+ connectx_port_config
+
+ Or in the manual way:
+
+ .. code-block:: console
+
+ PCI=<NIC PCI address>
+ echo eth > "/sys/bus/pci/devices/$PCI/mlx4_port0"
+ echo eth > "/sys/bus/pci/devices/$PCI/mlx4_port1"
+
+5. In case of bare metal or hypervisor, configure optimized steering mode
+ by adding the following line to ``/etc/modprobe.d/mlx4_core.conf``:
+
+ .. code-block:: console
+
+ options mlx4_core log_num_mgm_entry_size=-7
+
+ .. note::
+
+ If VLAN filtering is used, set log_num_mgm_entry_size=-1.
+ Performance degradation can occur on this case.
+
+6. Restart the driver:
+
+ .. code-block:: console
+
+ /etc/init.d/openibd restart
+
+ or:
+
+ .. code-block:: console
+
+ service openibd restart
+
+7. Compile DPDK and you are ready to go. See instructions on
+ :ref:`Development Kit Build System <Development_Kit_Build_System>`
+
+Performance tuning
+------------------
+
+1. Verify the optimized steering mode is configured:
+
+ .. code-block:: console
+
+ cat /sys/module/mlx4_core/parameters/log_num_mgm_entry_size
+
+2. Use environment variable MLX4_INLINE_RECV_SIZE=64 to get maximum
+ performance for 64B messages.
+
+3. Use the CPU near local NUMA node to which the PCIe adapter is connected,
+ for better performance. For VMs, verify that the right CPU
+ and NUMA node are pinned according to the above. Run:
+
+ .. code-block:: console
+
+ lstopo-no-graphics
+
+ to identify the NUMA node to which the PCIe adapter is connected.
+
+4. If more than one adapter is used, and root complex capabilities allow
+ to put both adapters on the same NUMA node without PCI bandwidth degradation,
+ it is recommended to locate both adapters on the same NUMA node.
+ This in order to forward packets from one to the other without
+ NUMA performance penalty.
+
+5. Disable pause frames:
+
+ .. code-block:: console
+
+ ethtool -A <netdev> rx off tx off
+
+6. Verify IO non-posted prefetch is disabled by default. This can be checked
+ via the BIOS configuration. Please contact you server provider for more
+ information about the settings.
+
+.. note::
+
+ On some machines, depends on the machine integrator, it is beneficial
+ to set the PCI max read request parameter to 1K. This can be
+ done in the following way:
+
+ To query the read request size use:
+
+ .. code-block:: console
+
+ setpci -s <NIC PCI address> 68.w
+
+ If the output is different than 3XXX, set it by:
+
+ .. code-block:: console
+
+ setpci -s <NIC PCI address> 68.w=3XXX
+
+ The XXX can be different on different systems. Make sure to configure
+ according to the setpci output.
+
git.droids-corp.org / dpdk.git / blobdiff