======================
The ice PMD (librte_pmd_ice) provides poll mode driver support for
-10/25 Gbps Intel® Ethernet 810 Series Network Adapters based on
+10/25/50/100 Gbps Intel® Ethernet 810 Series Network Adapters based on
the Intel Ethernet Controller E810.
- To get better performance on Intel platforms, please follow the "How to get best performance with NICs on Intel platforms"
section of the :ref:`Getting Started Guide for Linux <linux_gsg>`.
+Recommended Matching List
+-------------------------
+
+It is highly recommended to upgrade the ice kernel driver and firmware and
+DDP packages to avoid the compatibility issues with ice PMD. Here is the
+suggested matching list.
+
+ +----------------------+-----------------------+------------------+----------------+-------------------+
+ | DPDK version | Kernel driver version | Firmware version | DDP OS Package | DDP COMMS Package |
+ +======================+=======================+==================+================+===================+
+ | 19.11 | 0.12.25 | 1.1.16.39 | 1.3.4 | 1.3.10 |
+ +----------------------+-----------------------+------------------+----------------+-------------------+
+ | 19.08 (experimental) | 0.10.1 | 1.1.12.7 | 1.2.0 | N/A |
+ +----------------------+-----------------------+------------------+----------------+-------------------+
+ | 19.05 (experimental) | 0.9.4 | 1.1.10.16 | 1.1.0 | N/A |
+ +----------------------+-----------------------+------------------+----------------+-------------------+
Pre-Installation Configuration
------------------------------
Toggle display of generic debugging messages.
+- ``CONFIG_RTE_LIBRTE_ICE_16BYTE_RX_DESC`` (default ``n``)
+
+ Toggle to use a 16-byte RX descriptor, by default the RX descriptor is 32 byte.
+
Runtime Config Options
~~~~~~~~~~~~~~~~~~~~~~
-- ``Maximum Number of Queue Pairs``
+- ``Safe Mode Support`` (default ``0``)
+
+ If driver failed to load OS package, by default driver's initialization failed.
+ But if user intend to use the device without OS package, user can take ``devargs``
+ parameter ``safe-mode-support``, for example::
+
+ -w 80:00.0,safe-mode-support=1
+
+ Then the driver will be initialized successfully and the device will enter Safe Mode.
+ NOTE: In Safe mode, only very limited features are available, features like RSS,
+ checksum, fdir, tunneling ... are all disabled.
+
+- ``Generic Flow Pipeline Mode Support`` (default ``0``)
+
+ In pipeline mode, a flow can be set at one specific stage by setting parameter
+ ``priority``. Currently, we support two stages: priority = 0 or !0. Flows with
+ priority 0 located at the first pipeline stage which typically be used as a firewall
+ to drop the packet on a blacklist(we called it permission stage). At this stage,
+ flow rules are created for the device's exact match engine: switch. Flows with priority
+ !0 located at the second stage, typically packets are classified here and be steered to
+ specific queue or queue group (we called it distribution stage), At this stage, flow
+ rules are created for device's flow director engine.
+ For none-pipeline mode, ``priority`` is ignored, a flow rule can be created as a flow director
+ rule or a switch rule depends on its pattern/action and the resource allocation situation,
+ all flows are virtually at the same pipeline stage.
+ By default, generic flow API is enabled in none-pipeline mode, user can choose to
+ use pipeline mode by setting ``devargs`` parameter ``pipeline-mode-support``,
+ for example::
+
+ -w 80:00.0,pipeline-mode-support=1
+
+- ``Flow Mark Support`` (default ``0``)
+
+ This is a hint to the driver to select the data path that supports flow mark extraction
+ by default.
+ NOTE: This is an experimental devarg, it will be removed when any of below conditions
+ is ready.
+ 1) all data paths support flow mark (currently vPMD does not)
+ 2) a new offload like RTE_DEV_RX_OFFLOAD_FLOW_MARK be introduced as a standard way to hint.
+ Example::
+
+ -w 80:00.0,flow-mark-support=1
+
+- ``Protocol extraction for per queue``
+
+ Configure the RX queues to do protocol extraction into mbuf for protocol
+ handling acceleration, like checking the TCP SYN packets quickly.
+
+ The argument format is::
+
+ -w 18:00.0,proto_xtr=<queues:protocol>[<queues:protocol>...]
+ -w 18:00.0,proto_xtr=<protocol>
+
+ Queues are grouped by ``(`` and ``)`` within the group. The ``-`` character
+ is used as a range separator and ``,`` is used as a single number separator.
+ The grouping ``()`` can be omitted for single element group. If no queues are
+ specified, PMD will use this protocol extraction type for all queues.
+
+ Protocol is : ``vlan, ipv4, ipv6, ipv6_flow, tcp``.
+
+ .. code-block:: console
+
+ testpmd -w 18:00.0,proto_xtr='[(1,2-3,8-9):tcp,10-13:vlan]'
+
+ This setting means queues 1, 2-3, 8-9 are TCP extraction, queues 10-13 are
+ VLAN extraction, other queues run with no protocol extraction.
+
+ .. code-block:: console
+
+ testpmd -w 18:00.0,proto_xtr=vlan,proto_xtr='[(1,2-3,8-9):tcp,10-23:ipv6]'
+
+ This setting means queues 1, 2-3, 8-9 are TCP extraction, queues 10-23 are
+ IPv6 extraction, other queues use the default VLAN extraction.
+
+ The extraction metadata is copied into the registered dynamic mbuf field, and
+ the related dynamic mbuf flags is set.
+
+ .. table:: Protocol extraction : ``vlan``
+
+ +----------------------------+----------------------------+
+ | VLAN2 | VLAN1 |
+ +======+===+=================+======+===+=================+
+ | PCP | D | VID | PCP | D | VID |
+ +------+---+-----------------+------+---+-----------------+
+
+ VLAN1 - single or EVLAN (first for QinQ).
+
+ VLAN2 - C-VLAN (second for QinQ).
+
+ .. table:: Protocol extraction : ``ipv4``
+
+ +----------------------------+----------------------------+
+ | IPHDR2 | IPHDR1 |
+ +======+=======+=============+==============+=============+
+ | Ver |Hdr Len| ToS | TTL | Protocol |
+ +------+-------+-------------+--------------+-------------+
+
+ IPHDR1 - IPv4 header word 4, "TTL" and "Protocol" fields.
+
+ IPHDR2 - IPv4 header word 0, "Ver", "Hdr Len" and "Type of Service" fields.
- The maximum number of queue pairs is decided by HW. If not configured, APP
- uses the number from HW. Users can check the number by calling the API
- ``rte_eth_dev_info_get``.
- If users want to limit the number of queues, they can set a smaller number
- using EAL parameter like ``max_queue_pair_num=n``.
+ .. table:: Protocol extraction : ``ipv6``
+ +----------------------------+----------------------------+
+ | IPHDR2 | IPHDR1 |
+ +=====+=============+========+=============+==============+
+ | Ver |Traffic class| Flow | Next Header | Hop Limit |
+ +-----+-------------+--------+-------------+--------------+
+
+ IPHDR1 - IPv6 header word 3, "Next Header" and "Hop Limit" fields.
+
+ IPHDR2 - IPv6 header word 0, "Ver", "Traffic class" and high 4 bits of
+ "Flow Label" fields.
+
+ .. table:: Protocol extraction : ``ipv6_flow``
+
+ +----------------------------+----------------------------+
+ | IPHDR2 | IPHDR1 |
+ +=====+=============+========+============================+
+ | Ver |Traffic class| Flow Label |
+ +-----+-------------+-------------------------------------+
+
+ IPHDR1 - IPv6 header word 1, 16 low bits of the "Flow Label" field.
+
+ IPHDR2 - IPv6 header word 0, "Ver", "Traffic class" and high 4 bits of
+ "Flow Label" fields.
+
+ .. table:: Protocol extraction : ``tcp``
+
+ +----------------------------+----------------------------+
+ | TCPHDR2 | TCPHDR1 |
+ +============================+======+======+==============+
+ | Reserved |Offset| RSV | Flags |
+ +----------------------------+------+------+--------------+
+
+ TCPHDR1 - TCP header word 6, "Data Offset" and "Flags" fields.
+
+ TCPHDR2 - Reserved
+
+ Use ``rte_net_ice_dynf_proto_xtr_metadata_get`` to access the protocol
+ extraction metadata, and use ``RTE_PKT_RX_DYNF_PROTO_XTR_*`` to get the
+ metadata type of ``struct rte_mbuf::ol_flags``.
+
+ The ``rte_net_ice_dump_proto_xtr_metadata`` routine shows how to
+ access the protocol extraction result in ``struct rte_mbuf``.
Driver compilation and testing
------------------------------
Refer to the document :ref:`compiling and testing a PMD for a NIC <pmd_build_and_test>`
for details.
+Features
+--------
+
+Vector PMD
+~~~~~~~~~~
+
+Vector PMD for RX and TX path are selected automatically. The paths
+are chosen based on 2 conditions.
+
+- ``CPU``
+ On the X86 platform, the driver checks if the CPU supports AVX2.
+ If it's supported, AVX2 paths will be chosen. If not, SSE is chosen.
+
+- ``Offload features``
+ The supported HW offload features are described in the document ice_vec.ini.
+ If any not supported features are used, ICE vector PMD is disabled and the
+ normal paths are chosen.
+
+Malicious driver detection (MDD)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+It's not appropriate to send a packet, if this packet's destination MAC address
+is just this port's MAC address. If SW tries to send such packets, HW will
+report a MDD event and drop the packets.
+
+The APPs based on DPDK should avoid providing such packets.
+
+Sample Application Notes
+------------------------
+
+Vlan filter
+~~~~~~~~~~~
+
+Vlan filter only works when Promiscuous mode is off.
+
+To start ``testpmd``, and add vlan 10 to port 0:
+
+.. code-block:: console
+
+ ./app/testpmd -l 0-15 -n 4 -- -i
+ ...
+
+ testpmd> rx_vlan add 10 0
Limitations or Known issues
---------------------------
-19.02 limitation
-~~~~~~~~~~~~~~~~
-
-Ice code released in 19.02 is for evaluation only.
+The Intel E810 requires a programmable pipeline package be downloaded
+by the driver to support normal operations. The E810 has a limited
+functionality built in to allow PXE boot and other use cases, but the
+driver must download a package file during the driver initialization
+stage.
+The default DDP package file name is ice.pkg. For a specific NIC, the
+DDP package supposed to be loaded can have a filename: ice-xxxxxx.pkg,
+where 'xxxxxx' is the 64-bit PCIe Device Serial Number of the NIC. For
+example, if the NIC's device serial number is 00-CC-BB-FF-FF-AA-05-68,
+the device-specific DDP package filename is ice-00ccbbffffaa0568.pkg
+(in hex and all low case). During initialization, the driver searches
+in the following paths in order: /lib/firmware/updates/intel/ice/ddp
+and /lib/firmware/intel/ice/ddp. The corresponding device-specific DDP
+package will be downloaded first if the file exists. If not, then the
+driver tries to load the default package. The type of loaded package
+is stored in ``ice_adapter->active_pkg_type``.
-Promiscuous mode not supported
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-As promiscuous mode is not supported as this stage, a port can only receive the
-packets which destination MAC address is this port's own.
+A symbolic link to the DDP package file is also ok. The same package
+file is used by both the kernel driver and the DPDK PMD.
+19.02 limitation
+~~~~~~~~~~~~~~~~
-TX anti-spoofing cannot be disabled
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-TX anti-spoofing is enabled by default. At this stage it's not supported to
-disable it. So any TX packet which source MAC address is not this port's own
-will be dropped by HW. It means io-fwd is not supported now. Recommand to use
-MAC-fwd for evaluation.
+Ice code released in 19.02 is for evaluation only.
git.droids-corp.org / dpdk.git / blobdiff