- RX VLAN stripping.
- TX VLAN insertion.
- RX CRC stripping configuration.
+- TX mbuf fast free offload.
- Promiscuous mode on PF and VF.
- Multicast promiscuous mode on PF and VF.
- Hardware checksum offloads.
- Hardware LRO.
- Hairpin.
- Multiple-thread flow insertion.
+- Matching on GTP extension header with raw encap/decap action.
+- Matching on Geneve TLV option header with raw encap/decap action.
+- RSS support in sample action.
+- E-Switch mirroring and jump.
+- E-Switch mirroring and modify.
+- 21844 flow priorities for ingress or egress flow groups greater than 0 and for any transfer
+ flow group.
Limitations
-----------
- OAM
- protocol type
- options length
- Currently, the only supported options length value is 0.
+
+- Match on Geneve TLV option is supported on the following fields:
+
+ - Class
+ - Type
+ - Length
+ - Data
+
+ Only one Class/Type/Length Geneve TLV option is supported per shared device.
+ Class/Type/Length fields must be specified as well as masks.
+ Class/Type/Length specified masks must be full.
+ Matching Geneve TLV option without specifying data is not supported.
+ Matching Geneve TLV option with ``data & mask == 0`` is not supported.
- VF: flow rules created on VF devices can only match traffic targeted at the
configured MAC addresses (see ``rte_eth_dev_mac_addr_add()``).
- msg_type
- teid
+- Match on GTP extension header only for GTP PDU session container (next
+ extension header type = 0x85).
+- Match on GTP extension header is not supported in group 0.
+
- No Tx metadata go to the E-Switch steering domain for the Flow group 0.
The flows within group 0 and set metadata action are rejected by hardware.
for some NICs (such as ConnectX-6 Dx, ConnectX-6 Lx, and BlueField-2).
The capability bit ``scatter_fcs_w_decap_disable`` shows NIC support.
+- TX mbuf fast free:
+
+ - fast free offload assumes the all mbufs being sent are originated from the
+ same memory pool and there is no any extra references to the mbufs (the
+ reference counter for each mbuf is equal 1 on tx_burst call). The latter
+ means there should be no any externally attached buffers in mbufs. It is
+ an application responsibility to provide the correct mbufs if the fast
+ free offload is engaged. The mlx5 PMD implicitly produces the mbufs with
+ externally attached buffers if MPRQ option is enabled, hence, the fast
+ free offload is neither supported nor advertised if there is MPRQ enabled.
+
- Sample flow:
- - Supports ``RTE_FLOW_ACTION_TYPE_SAMPLE`` action only within NIC Rx and E-Switch steering domain.
- - The E-Switch Sample flow must have the eswitch_manager VPORT destination (PF or ECPF) and no additional actions.
- - For ConnectX-5, the ``RTE_FLOW_ACTION_TYPE_SAMPLE`` is typically used as first action in the E-Switch egress flow if with header modify or encapsulation actions.
+ - Supports ``RTE_FLOW_ACTION_TYPE_SAMPLE`` action only within NIC Rx and
+ E-Switch steering domain.
+ - For E-Switch Sampling flow with sample ratio > 1, additional actions are not
+ supported in the sample actions list.
+ - For ConnectX-5, the ``RTE_FLOW_ACTION_TYPE_SAMPLE`` is typically used as
+ first action in the E-Switch egress flow if with header modify or
+ encapsulation actions.
+ - For NIC Rx flow, supports ``MARK``, ``COUNT``, ``QUEUE``, ``RSS`` in the
+ sample actions list.
+ - For E-Switch mirroring flow, supports ``RAW ENCAP``, ``Port ID`` in the
+ sample actions list.
+
+- Modify Field flow:
+
+ - Supports the 'set' operation only for ``RTE_FLOW_ACTION_TYPE_MODIFY_FIELD`` action.
+ - Modification of an arbitrary place in a packet via the special ``RTE_FLOW_FIELD_START`` Field ID is not supported.
+ - Encapsulation levels are not supported, can modify outermost header fields only.
+ - Offsets must be 32-bits aligned, cannot skip past the boundary of a field.
- IPv6 header item 'proto' field, indicating the next header protocol, should
not be set as extension header.
A nonzero value enables the compression of CQE on RX side. This feature
allows to save PCI bandwidth and improve performance. Enabled by default.
Different compression formats are supported in order to achieve the best
- performance for different traffic patterns. Hash RSS format is the default.
+ performance for different traffic patterns. Default format depends on
+ Multi-Packet Rx queue configuration: Hash RSS format is used in case
+ MPRQ is disabled, Checksum format is used in case MPRQ is enabled.
Specifying 2 as a ``rxq_cqe_comp_en`` value selects Flow Tag format for
better compression rate in case of RTE Flow Mark traffic.
Specifying 3 as a ``rxq_cqe_comp_en`` value selects Checksum format.
Specifying 4 as a ``rxq_cqe_comp_en`` value selects L3/L4 Header format for
better compression rate in case of mixed TCP/UDP and IPv4/IPv6 traffic.
+ CQE compression format selection requires DevX to be enabled. If there is
+ no DevX enabled/supported the value is reset to 1 by default.
Supported on:
+------+-----------+-----------+-------------+-------------+
| 1 | 24 bits | vary 0-32 | 32 bits | yes |
+------+-----------+-----------+-------------+-------------+
- | 2 | vary 0-32 | 32 bits | 32 bits | yes |
+ | 2 | vary 0-24 | 32 bits | 32 bits | yes |
+------+-----------+-----------+-------------+-------------+
If there is no E-Switch configuration the ``dv_xmeta_en`` parameter is
of the extensive metadata features. The legacy Verbs supports FLAG and
MARK metadata actions over NIC Rx steering domain only.
+ Setting META value to zero in flow action means there is no item provided
+ and receiving datapath will not report in mbufs the metadata are present.
+ Setting MARK value to zero in flow action means the zero FDIR ID value
+ will be reported on packet receiving.
+
+ For the MARK action the last 16 values in the full range are reserved for
+ internal PMD purposes (to emulate FLAG action). The valid range for the
+ MARK action values is 0-0xFFEF for the 16-bit mode and 0-xFFFFEF
+ for the 24-bit mode, the flows with the MARK action value outside
+ the specified range will be rejected.
+
- ``dv_flow_en`` parameter [int]
A nonzero value enables the DV flow steering assuming it is supported
- ``representor`` parameter [list]
This parameter can be used to instantiate DPDK Ethernet devices from
- existing port (or VF) representors configured on the device.
+ existing port (PF, VF or SF) representors configured on the device.
It is a standard parameter whose format is described in
:ref:`ethernet_device_standard_device_arguments`.
- For instance, to probe port representors 0 through 2::
+ For instance, to probe VF port representors 0 through 2::
+
+ representor=vf[0-2]
- representor=[0-2]
+ To probe SF port representors 0 through 2::
+
+ representor=sf[0-2]
- ``max_dump_files_num`` parameter [int]
or
FLEX_PARSER_PROFILE_ENABLE=1
+- enable Geneve TLV option flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=0
+
- enable GTP flow matching::
FLEX_PARSER_PROFILE_ENABLE=3
Enable switchdev mode
---------------------
-Switchdev mode is a mode in E-Switch, that binds between representor and VF.
-Representor is a port in DPDK that is connected to a VF in such a way
-that assuming there are no offload flows, each packet that is sent from the VF
-will be received by the corresponding representor. While each packet that is
-sent to a representor will be received by the VF.
+Switchdev mode is a mode in E-Switch, that binds between representor and VF or SF.
+Representor is a port in DPDK that is connected to a VF or SF in such a way
+that assuming there are no offload flows, each packet that is sent from the VF or SF
+will be received by the corresponding representor. While each packet that is or SF
+sent to a representor will be received by the VF or SF.
This is very useful in case of SRIOV mode, where the first packet that is sent
-by the VF will be received by the DPDK application which will decide if this
+by the VF or SF will be received by the DPDK application which will decide if this
flow should be offloaded to the E-Switch. After offloading the flow packet
-that the VF that are matching the flow will not be received any more by
+that the VF or SF that are matching the flow will not be received any more by
the DPDK application.
1. Enable SRIOV mode::
echo switchdev > /sys/class/net/<net device>/compat/devlink/mode
+SubFunction representor support
+-------------------------------
+SubFunction is a portion of the PCI device, a SF netdev has its own
+dedicated queues(txq, rxq). A SF netdev supports E-Switch representation
+offload similar to existing PF and VF representors. A SF shares PCI
+level resources with other SFs and/or with its parent PCI function.
+
+1. Configure SF feature::
+
+ mlxconfig -d <mst device> set PF_BAR2_SIZE=<0/1/2/3> PF_BAR2_ENABLE=1
+
+ Value of PF_BAR2_SIZE:
+
+ 0: 8 SFs
+ 1: 16 SFs
+ 2: 32 SFs
+ 3: 64 SFs
+
+2. Reset the FW::
+
+ mlxfwreset -d <mst device> reset
+
+3. Enable switchdev mode::
+
+ echo switchdev > /sys/class/net/<net device>/compat/devlink/mode
+
+4. Create SF::
+
+ mlnx-sf -d <PCI_BDF> -a create
+
+5. Probe SF representor::
+
+ testpmd> port attach <PCI_BDF>,representor=sf0,dv_flow_en=1
+
Performance tuning
------------------
Rx timestamp 17.11 4.14 16 4.2-1 12.21.1000 ConnectX-4
TSO 17.11 4.14 16 4.2-1 12.21.1000 ConnectX-4
LRO 19.08 N/A N/A 4.6-4 16.25.6406 ConnectX-5
- Buffer Split 20.11 N/A N/A 5.1-2 22.28.2006 ConnectX-6 Dx
+ Tx scheduling 20.08 N/A N/A 5.1-2 22.28.2006 ConnectX-6 Dx
+ Buffer Split 20.11 N/A N/A 5.1-2 16.28.2006 ConnectX-5
============== ===== ===== ========= ===== ========== =============
.. table:: Minimal SW/HW versions for rte_flow offloads
| | | | | rdma-core 23 |
| | | | | ConnectX-4 |
+-----------------------+-----------------+-----------------+
- | RSS shared action | | | | DPDK 20.11 |
- | | | N/A | | OFED 5.2 |
- | | | | | rdma-core 33 |
- | | | | | ConnectX-5 |
+ | Shared action | | | | |
+ | | | :numref:`sact`| | :numref:`sact`|
+ | | | | | |
+ | | | | | |
+-----------------------+-----------------+-----------------+
| | VLAN | | DPDK 19.11 | | DPDK 19.11 |
| | (of_pop_vlan / | | OFED 4.7-1 | | OFED 4.7-1 |
| | | rdma-core 32 | | N/A |
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
- | Age shared action | | DPDK 20.11 | | DPDK 20.11 |
+ | Encapsulation | | DPDK 21.02 | | DPDK 21.02 |
+ | GTP PSC | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 35 | | rdma-core 35 |
+ | | | ConnectX-6 Dx| | ConnectX-6 Dx |
+ +-----------------------+-----------------+-----------------+
+ | Encapsulation | | DPDK 21.02 | | DPDK 21.02 |
+ | GENEVE TLV option | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 34 | | rdma-core 34 |
+ | | | ConnectX-6 Dx | | ConnectX-6 Dx |
+ +-----------------------+-----------------+-----------------+
+ | Modify Field | | DPDK 21.02 | | DPDK 21.02 |
+ | | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 35 | | rdma-core 35 |
+ | | | ConnectX-5 | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
+
+.. table:: Minimal SW/HW versions for shared action offload
+ :name: sact
+
+ +-----------------------+-----------------+-----------------+
+ | Shared Action | with E-Switch | with NIC |
+ +=======================+=================+=================+
+ | RSS | | | | DPDK 20.11 |
+ | | | N/A | | OFED 5.2 |
+ | | | | | rdma-core 33 |
+ | | | | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
+ | Age | | DPDK 20.11 | | DPDK 20.11 |
| | | OFED 5.2 | | OFED 5.2 |
| | | rdma-core 32 | | rdma-core 32 |
| | | ConnectX-6 Dx| | ConnectX-6 Dx |
#. Request huge pages::
- echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages/nr_hugepages
+ dpdk-hugepages.py --setup 2G
#. Start testpmd with basic parameters::
- testpmd -l 8-15 -n 4 -a 05:00.0 -a 05:00.1 -a 06:00.0 -a 06:00.1 -- --rxq=2 --txq=2 -i
+ dpdk-testpmd -l 8-15 -n 4 -a 05:00.0 -a 05:00.1 -a 06:00.0 -a 06:00.1 -- --rxq=2 --txq=2 -i
Example output::
git.droids-corp.org / dpdk.git / blobdiff