Copyright 2015 6WIND S.A.
Copyright 2015 Mellanox Technologies, Ltd
+.. include:: <isonum.txt>
+
MLX5 poll mode driver
=====================
-The MLX5 poll mode driver library (**librte_pmd_mlx5**) provides support
+The MLX5 poll mode driver library (**librte_net_mlx5**) provides support
for **Mellanox ConnectX-4**, **Mellanox ConnectX-4 Lx** , **Mellanox
-ConnectX-5**, **Mellanox ConnectX-6**, **Mellanox ConnectX-6DX** and
-**Mellanox BlueField** families of 10/25/40/50/100/200 Gb/s adapters
-as well as their virtual functions (VF) in SR-IOV context.
+ConnectX-5**, **Mellanox ConnectX-6**, **Mellanox ConnectX-6 Dx**, **Mellanox
+ConnectX-6 Lx**, **Mellanox BlueField** and **Mellanox BlueField-2** families
+of 10/25/40/50/100/200 Gb/s adapters as well as their virtual functions (VF)
+in SR-IOV context.
Information and documentation about these adapters can be found on the
`Mellanox website <http://www.mellanox.com>`__. Help is also provided by the
There is also a `section dedicated to this poll mode driver
<http://www.mellanox.com/page/products_dyn?product_family=209&mtag=pmd_for_dpdk>`__.
-.. note::
-
- Due to external dependencies, this driver is disabled in default configuration
- of the "make" build. It can be enabled with ``CONFIG_RTE_LIBRTE_MLX5_PMD=y``
- or by using "meson" build system which will detect dependencies.
Design
------
Besides its dependency on libibverbs (that implies libmlx5 and associated
-kernel support), librte_pmd_mlx5 relies heavily on system calls for control
+kernel support), librte_net_mlx5 relies heavily on system calls for control
operations such as querying/updating the MTU and flow control parameters.
For security reasons and robustness, this driver only deals with virtual
- DevX allows to access firmware objects
- Direct Rules manages flow steering at low-level hardware layer
-Enabling librte_pmd_mlx5 causes DPDK applications to be linked against
+Enabling librte_net_mlx5 causes DPDK applications to be linked against
libibverbs.
Features
- Multi arch support: x86_64, POWER8, ARMv8, i686.
- Multiple TX and RX queues.
-- Support for scattered TX and RX frames.
+- Support for scattered TX frames.
+- Advanced support for scattered Rx frames with tunable buffer attributes.
- IPv4, IPv6, TCPv4, TCPv6, UDPv4 and UDPv6 RSS on any number of queues.
- RSS using different combinations of fields: L3 only, L4 only or both,
and source only, destination only or both.
- RX VLAN stripping.
- TX VLAN insertion.
- RX CRC stripping configuration.
+- TX mbuf fast free offload.
- Promiscuous mode on PF and VF.
- Multicast promiscuous mode on PF and VF.
- Hardware checksum offloads.
increment/decrement, count, drop, mark. For details please see :ref:`mlx5_offloads_support`.
- Flow insertion rate of more then million flows per second, when using Direct Rules.
- Support for multiple rte_flow groups.
+- Per packet no-inline hint flag to disable packet data copying into Tx descriptors.
- Hardware LRO.
+- Hairpin.
+- Multiple-thread flow insertion.
+- Matching on IPv4 Internet Header Length (IHL).
+- Matching on GTP extension header with raw encap/decap action.
+- Matching on Geneve TLV option header with raw encap/decap action.
+- RSS support in sample action.
+- E-Switch mirroring and jump.
+- E-Switch mirroring and modify.
+- 21844 flow priorities for ingress or egress flow groups greater than 0 and for any transfer
+ flow group.
+- Flow metering, including meter policy API.
+- Flow meter hierarchy.
+- Flow integrity offload API.
+- Connection tracking.
+- Sub-Function representors.
+- Sub-Function.
+
Limitations
-----------
+- Windows support:
+
+ On Windows, the features are limited:
+
+ - Promiscuous mode is not supported
+ - The following rules are supported:
+
+ - IPv4/UDP with CVLAN filtering
+ - Unicast MAC filtering
+
+ - Additional rules are supported from WinOF2 version 2.70:
+
+ - IPv4/TCP with CVLAN filtering
+ - L4 steering rules for port RSS of UDP, TCP and IP
+
- For secondary process:
- Forked secondary process not supported.
Will match any ipv4 packet (VLAN included).
+- When using Verbs flow engine (``dv_flow_en`` = 0), multi-tagged(QinQ) match is not supported.
+
+- When using DV flow engine (``dv_flow_en`` = 1), flow pattern with any VLAN specification will match only single-tagged packets unless the ETH item ``type`` field is 0x88A8 or the VLAN item ``has_more_vlan`` field is 1.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / ipv4 / end ...
+
+ Will match any ipv4 packet.
+ The flow rules::
+
+ flow create 0 ingress pattern eth / vlan / end ...
+ flow create 0 ingress pattern eth has_vlan is 1 / end ...
+ flow create 0 ingress pattern eth type is 0x8100 / end ...
+
+ Will match single-tagged packets only, with any VLAN ID value.
+ The flow rules::
+
+ flow create 0 ingress pattern eth type is 0x88A8 / end ...
+ flow create 0 ingress pattern eth / vlan has_more_vlan is 1 / end ...
+
+ Will match multi-tagged packets only, with any VLAN ID value.
+
+- A flow pattern with 2 sequential VLAN items is not supported.
+
- VLAN pop offload command:
- Flow rules having a VLAN pop offload command as one of their actions and
are lacking a match on VLAN as one of their items are not supported.
- - The command is not supported on egress traffic.
+ - The command is not supported on egress traffic in NIC mode.
-- VLAN push offload is not supported on ingress traffic.
+- VLAN push offload is not supported on ingress traffic in NIC mode.
- VLAN set PCP offload is not supported on existing headers.
size and ``txq_inline_min`` settings and may be from 2 (worst case forced by maximal
inline settings) to 58.
-- Flows with a VXLAN Network Identifier equal (or ends to be equal)
- to 0 are not supported.
+- Match on VXLAN supports the following fields only:
-- VXLAN TSO and checksum offloads are not supported on VM.
+ - VNI
+ - Last reserved 8-bits
+
+ Last reserved 8-bits matching is only supported When using DV flow
+ engine (``dv_flow_en`` = 1).
+ Group zero's behavior may differ which depends on FW.
+ Matching value equals 0 (value & mask) is not supported.
- L3 VXLAN and VXLAN-GPE tunnels cannot be supported together with MPLSoGRE and MPLSoUDP.
- OAM
- protocol type
- options length
- Currently, the only supported options length value is 0.
+
+- Match on Geneve TLV option is supported on the following fields:
+
+ - Class
+ - Type
+ - Length
+ - Data
+
+ Only one Class/Type/Length Geneve TLV option is supported per shared device.
+ Class/Type/Length fields must be specified as well as masks.
+ Class/Type/Length specified masks must be full.
+ Matching Geneve TLV option without specifying data is not supported.
+ Matching Geneve TLV option with ``data & mask == 0`` is not supported.
- VF: flow rules created on VF devices can only match traffic targeted at the
configured MAC addresses (see ``rte_eth_dev_mac_addr_add()``).
- Match on GTP tunnel header item supports the following fields only:
+ - v_pt_rsv_flags: E flag, S flag, PN flag
- msg_type
- teid
+- Match on GTP extension header only for GTP PDU session container (next
+ extension header type = 0x85).
+- Match on GTP extension header is not supported in group 0.
+
- No Tx metadata go to the E-Switch steering domain for the Flow group 0.
The flows within group 0 and set metadata action are rejected by hardware.
the device. In case of ungraceful program termination, some entries may
remain present and should be removed manually by other means.
+- Buffer split offload is supported with regular Rx burst routine only,
+ no MPRQ feature or vectorized code can be engaged.
+
- When Multi-Packet Rx queue is configured (``mprq_en``), a Rx packet can be
- externally attached to a user-provided mbuf with having EXT_ATTACHED_MBUF in
+ externally attached to a user-provided mbuf with having RTE_MBUF_F_EXTERNAL in
ol_flags. As the mempool for the external buffer is managed by PMD, all the
Rx mbufs must be freed before the device is closed. Otherwise, the mempool of
the external buffers will be freed by PMD and the application which still
- If Multi-Packet Rx queue is configured (``mprq_en``) and Rx CQE compression is
enabled (``rxq_cqe_comp_en``) at the same time, RSS hash result is not fully
- supported. Some Rx packets may not have PKT_RX_RSS_HASH.
+ supported. Some Rx packets may not have RTE_MBUF_F_RX_RSS_HASH.
- IPv6 Multicast messages are not supported on VM, while promiscuous mode
and allmulticast mode are both set to off.
To receive IPv6 Multicast messages on VM, explicitly set the relevant
MAC address using rte_eth_dev_mac_addr_add() API.
+- To support a mixed traffic pattern (some buffers from local host memory, some
+ buffers from other devices) with high bandwidth, a mbuf flag is used.
+
+ An application hints the PMD whether or not it should try to inline the
+ given mbuf data buffer. PMD should do the best effort to act upon this request.
+
+ The hint flag ``RTE_PMD_MLX5_FINE_GRANULARITY_INLINE`` is dynamic,
+ registered by application with rte_mbuf_dynflag_register(). This flag is
+ purely driver-specific and declared in PMD specific header ``rte_pmd_mlx5.h``,
+ which is intended to be used by the application.
+
+ To query the supported specific flags in runtime,
+ the function ``rte_pmd_mlx5_get_dyn_flag_names`` returns the array of
+ currently (over present hardware and configuration) supported specific flags.
+ The "not inline hint" feature operating flow is the following one:
+
+ - application starts
+ - probe the devices, ports are created
+ - query the port capabilities
+ - if port supporting the feature is found
+ - register dynamic flag ``RTE_PMD_MLX5_FINE_GRANULARITY_INLINE``
+ - application starts the ports
+ - on ``dev_start()`` PMD checks whether the feature flag is registered and
+ enables the feature support in datapath
+ - application might set the registered flag bit in ``ol_flags`` field
+ of mbuf being sent and PMD will handle ones appropriately.
+
- The amount of descriptors in Tx queue may be limited by data inline settings.
Inline data require the more descriptor building blocks and overall block
amount may exceed the hardware supported limits. The application should
reduce the requested Tx size or adjust data inline settings with
``txq_inline_max`` and ``txq_inline_mpw`` devargs keys.
+- To provide the packet send scheduling on mbuf timestamps the ``tx_pp``
+ parameter should be specified.
+ When PMD sees the RTE_MBUF_DYNFLAG_TX_TIMESTAMP_NAME set on the packet
+ being sent it tries to synchronize the time of packet appearing on
+ the wire with the specified packet timestamp. It the specified one
+ is in the past it should be ignored, if one is in the distant future
+ it should be capped with some reasonable value (in range of seconds).
+ These specific cases ("too late" and "distant future") can be optionally
+ reported via device xstats to assist applications to detect the
+ time-related problems.
+
+ The timestamp upper "too-distant-future" limit
+ at the moment of invoking the Tx burst routine
+ can be estimated as ``tx_pp`` option (in nanoseconds) multiplied by 2^23.
+ Please note, for the testpmd txonly mode,
+ the limit is deduced from the expression::
+
+ (n_tx_descriptors / burst_size + 1) * inter_burst_gap
+
+ There is no any packet reordering according timestamps is supposed,
+ neither within packet burst, nor between packets, it is an entirely
+ application responsibility to generate packets and its timestamps
+ in desired order. The timestamps can be put only in the first packet
+ in the burst providing the entire burst scheduling.
+
- E-Switch decapsulation Flow:
- can be applied to PF port only.
- The input buffer, providing the removal size, is not validated.
- The buffer size must match the length of the headers to be removed.
-- ICMP/ICMP6 code/type matching, IP-in-IP and MPLS flow matching are all
+- ICMP(code/type/identifier/sequence number) / ICMP6(code/type) matching, IP-in-IP and MPLS flow matching are all
mutually exclusive features which cannot be supported together
(see :ref:`mlx5_firmware_config`).
TCP header (122B).
- Rx queue with LRO offload enabled, receiving a non-LRO packet, can forward
it with size limited to max LRO size, not to max RX packet length.
+ - LRO can be used with outer header of TCP packets of the standard format:
+ eth (with or without vlan) / ipv4 or ipv6 / tcp / payload
+
+ Other TCP packets (e.g. with MPLS label) received on Rx queue with LRO enabled, will be received with bad checksum.
+ - LRO packet aggregation is performed by HW only for packet size larger than
+ ``lro_min_mss_size``. This value is reported on device start, when debug
+ mode is enabled.
+
+- CRC:
+
+ - ``DEV_RX_OFFLOAD_KEEP_CRC`` cannot be supported with decapsulation
+ for some NICs (such as ConnectX-6 Dx, ConnectX-6 Lx, and BlueField-2).
+ The capability bit ``scatter_fcs_w_decap_disable`` shows NIC support.
+
+- TX mbuf fast free:
+
+ - fast free offload assumes the all mbufs being sent are originated from the
+ same memory pool and there is no any extra references to the mbufs (the
+ reference counter for each mbuf is equal 1 on tx_burst call). The latter
+ means there should be no any externally attached buffers in mbufs. It is
+ an application responsibility to provide the correct mbufs if the fast
+ free offload is engaged. The mlx5 PMD implicitly produces the mbufs with
+ externally attached buffers if MPRQ option is enabled, hence, the fast
+ free offload is neither supported nor advertised if there is MPRQ enabled.
+
+- Sample flow:
+
+ - Supports ``RTE_FLOW_ACTION_TYPE_SAMPLE`` action only within NIC Rx and
+ E-Switch steering domain.
+ - For E-Switch Sampling flow with sample ratio > 1, additional actions are not
+ supported in the sample actions list.
+ - For ConnectX-5, the ``RTE_FLOW_ACTION_TYPE_SAMPLE`` is typically used as
+ first action in the E-Switch egress flow if with header modify or
+ encapsulation actions.
+ - For NIC Rx flow, supports ``MARK``, ``COUNT``, ``QUEUE``, ``RSS`` in the
+ sample actions list.
+ - For E-Switch mirroring flow, supports ``RAW ENCAP``, ``Port ID``,
+ ``VXLAN ENCAP``, ``NVGRE ENCAP`` in the sample actions list.
+
+- Modify Field flow:
+
+ - Supports the 'set' operation only for ``RTE_FLOW_ACTION_TYPE_MODIFY_FIELD`` action.
+ - Modification of an arbitrary place in a packet via the special ``RTE_FLOW_FIELD_START`` Field ID is not supported.
+ - Modification of the 802.1Q Tag, VXLAN Network or GENEVE Network ID's is not supported.
+ - Encapsulation levels are not supported, can modify outermost header fields only.
+ - Offsets must be 32-bits aligned, cannot skip past the boundary of a field.
+
+- IPv6 header item 'proto' field, indicating the next header protocol, should
+ not be set as extension header.
+ In case the next header is an extension header, it should not be specified in
+ IPv6 header item 'proto' field.
+ The last extension header item 'next header' field can specify the following
+ header protocol type.
+
+- Hairpin:
+
+ - Hairpin between two ports could only manual binding and explicit Tx flow mode. For single port hairpin, all the combinations of auto/manual binding and explicit/implicit Tx flow mode could be supported.
+ - Hairpin in switchdev SR-IOV mode is not supported till now.
+
+- Meter:
+
+ - All the meter colors with drop action will be counted only by the global drop statistics.
+ - Yellow detection is only supported with ASO metering.
+ - Red color must be with drop action.
+ - Meter statistics are supported only for drop case.
+ - A meter action created with pre-defined policy must be the last action in the flow except single case where the policy actions are:
+ - green: NULL or END.
+ - yellow: NULL or END.
+ - RED: DROP / END.
+ - The only supported meter policy actions:
+ - green: QUEUE, RSS, PORT_ID, JUMP, DROP, MARK and SET_TAG.
+ - yellow: QUEUE, RSS, PORT_ID, JUMP, DROP, MARK and SET_TAG.
+ - RED: must be DROP.
+ - Policy actions of RSS for green and yellow should have the same configuration except queues.
+ - meter profile packet mode is supported.
+ - meter profiles of RFC2697, RFC2698 and RFC4115 are supported.
+
+- Integrity:
+
+ - Integrity offload is enabled for **ConnectX-6** family.
+ - Verification bits provided by the hardware are ``l3_ok``, ``ipv4_csum_ok``, ``l4_ok``, ``l4_csum_ok``.
+ - ``level`` value 0 references outer headers.
+ - Multiple integrity items not supported in a single flow rule.
+ - Flow rule items supplied by application must explicitly specify network headers referred by integrity item.
+ For example, if integrity item mask sets ``l4_ok`` or ``l4_csum_ok`` bits, reference to L4 network header,
+ TCP or UDP, must be in the rule pattern as well::
+
+ flow create 0 ingress pattern integrity level is 0 value mask l3_ok value spec l3_ok / eth / ipv6 / end …
+ or
+ flow create 0 ingress pattern integrity level is 0 value mask l4_ok value spec 0 / eth / ipv4 proto is udp / end …
+
+- Connection tracking:
+
+ - Cannot co-exist with ASO meter, ASO age action in a single flow rule.
+ - Flow rules insertion rate and memory consumption need more optimization.
+ - 256 ports maximum.
+ - 4M connections maximum.
+
+- Multi-thread flow insertion:
+
+ - In order to achieve best insertion rate, application should manage the flows per lcore.
+ - Better to disable memory reclaim by setting ``reclaim_mem_mode`` to 0 to accelerate the flow object allocation and release with cache.
Statistics
----------
Compilation options
~~~~~~~~~~~~~~~~~~~
-These options can be modified in the ``.config`` file.
-
-- ``CONFIG_RTE_LIBRTE_MLX5_PMD`` (default **n**)
-
- Toggle compilation of librte_pmd_mlx5 itself.
-
-- ``CONFIG_RTE_IBVERBS_LINK_DLOPEN`` (default **n**)
-
- Build PMD with additional code to make it loadable without hard
- dependencies on **libibverbs** nor **libmlx5**, which may not be installed
- on the target system.
+The ibverbs libraries can be linked with this PMD in a number of ways,
+configured by the ``ibverbs_link`` build option:
- In this mode, their presence is still required for it to run properly,
- however their absence won't prevent a DPDK application from starting (with
- ``CONFIG_RTE_BUILD_SHARED_LIB`` disabled) and they won't show up as
- missing with ``ldd(1)``.
+- ``shared`` (default): the PMD depends on some .so files.
- It works by moving these dependencies to a purpose-built rdma-core "glue"
- plug-in which must either be installed in a directory whose name is based
- on ``CONFIG_RTE_EAL_PMD_PATH`` suffixed with ``-glue`` if set, or in a
- standard location for the dynamic linker (e.g. ``/lib``) if left to the
- default empty string (``""``).
+- ``dlopen``: Split the dependencies glue in a separate library
+ loaded when needed by dlopen.
+ It make dependencies on libibverbs and libmlx4 optional,
+ and has no performance impact.
- This option has no performance impact.
-
-- ``CONFIG_RTE_IBVERBS_LINK_STATIC`` (default **n**)
-
- Embed static flavor of the dependencies **libibverbs** and **libmlx5**
+- ``static``: Embed static flavor of the dependencies libibverbs and libmlx4
in the PMD shared library or the executable static binary.
-- ``CONFIG_RTE_LIBRTE_MLX5_DEBUG`` (default **n**)
-
- Toggle debugging code and stricter compilation flags. Enabling this option
- adds additional run-time checks and debugging messages at the cost of
- lower performance.
-
-.. note::
-
- For BlueField, target should be set to ``arm64-bluefield-linux-gcc``. This
- will enable ``CONFIG_RTE_LIBRTE_MLX5_PMD`` and set ``RTE_CACHE_LINE_SIZE`` to
- 64. Default armv8a configuration of make build and meson build set it to 128
- then brings performance degradation.
-
-This option is available in meson:
-
-- ``ibverbs_link`` can be ``static``, ``shared``, or ``dlopen``.
-
Environment variables
~~~~~~~~~~~~~~~~~~~~~
A list of directories in which to search for the rdma-core "glue" plug-in,
separated by colons or semi-colons.
- Only matters when compiled with ``CONFIG_RTE_IBVERBS_LINK_DLOPEN``
- enabled and most useful when ``CONFIG_RTE_EAL_PMD_PATH`` is also set,
- since ``LD_LIBRARY_PATH`` has no effect in this case.
-
- ``MLX5_SHUT_UP_BF``
Configures HW Tx doorbell register as IO-mapped.
Run-time configuration
~~~~~~~~~~~~~~~~~~~~~~
-- librte_pmd_mlx5 brings kernel network interfaces up during initialization
+- librte_net_mlx5 brings kernel network interfaces up during initialization
because it is affected by their state. Forcing them down prevents packets
reception.
- **ethtool** operations on related kernel interfaces also affect the PMD.
+Run as non-root
+^^^^^^^^^^^^^^^
+
+In order to run as a non-root user,
+some capabilities must be granted to the application::
+
+ setcap cap_sys_admin,cap_net_admin,cap_net_raw,cap_ipc_lock+ep <dpdk-app>
+
+Below are the reasons of the need for each capability:
+
+``cap_sys_admin``
+ When using physical addresses (PA mode), with Linux >= 4.0,
+ for access to ``/proc/self/pagemap``.
+
+``cap_net_admin``
+ For device configuration.
+
+``cap_net_raw``
+ For raw ethernet queue allocation through kernel driver.
+
+``cap_ipc_lock``
+ For DMA memory pinning.
+
+Driver options
+^^^^^^^^^^^^^^
+
- ``rxq_cqe_comp_en`` parameter [int]
A nonzero value enables the compression of CQE on RX side. This feature
allows to save PCI bandwidth and improve performance. Enabled by default.
+ Different compression formats are supported in order to achieve the best
+ performance for different traffic patterns. Default format depends on
+ Multi-Packet Rx queue configuration: Hash RSS format is used in case
+ MPRQ is disabled, Checksum format is used in case MPRQ is enabled.
+
+ Specifying 2 as a ``rxq_cqe_comp_en`` value selects Flow Tag format for
+ better compression rate in case of RTE Flow Mark traffic.
+ Specifying 3 as a ``rxq_cqe_comp_en`` value selects Checksum format.
+ Specifying 4 as a ``rxq_cqe_comp_en`` value selects L3/L4 Header format for
+ better compression rate in case of mixed TCP/UDP and IPv4/IPv6 traffic.
+ CQE compression format selection requires DevX to be enabled. If there is
+ no DevX enabled/supported the value is reset to 1 by default.
Supported on:
- - x86_64 with ConnectX-4, ConnectX-4 LX, ConnectX-5, ConnectX-6, ConnectX-6 DX
- and BlueField.
- - POWER9 and ARMv8 with ConnectX-4 LX, ConnectX-5, ConnectX-6, ConnectX-6 DX
- and BlueField.
-
-- ``rxq_cqe_pad_en`` parameter [int]
-
- A nonzero value enables 128B padding of CQE on RX side. The size of CQE
- is aligned with the size of a cacheline of the core. If cacheline size is
- 128B, the CQE size is configured to be 128B even though the device writes
- only 64B data on the cacheline. This is to avoid unnecessary cache
- invalidation by device's two consecutive writes on to one cacheline.
- However in some architecture, it is more beneficial to update entire
- cacheline with padding the rest 64B rather than striding because
- read-modify-write could drop performance a lot. On the other hand,
- writing extra data will consume more PCIe bandwidth and could also drop
- the maximum throughput. It is recommended to empirically set this
- parameter. Disabled by default.
-
- Supported on:
-
- - CPU having 128B cacheline with ConnectX-5 and BlueField.
+ - x86_64 with ConnectX-4, ConnectX-4 Lx, ConnectX-5, ConnectX-6, ConnectX-6 Dx,
+ ConnectX-6 Lx, BlueField and BlueField-2.
+ - POWER9 and ARMv8 with ConnectX-4 Lx, ConnectX-5, ConnectX-6, ConnectX-6 Dx,
+ ConnectX-6 Lx, BlueField and BlueField-2.
- ``rxq_pkt_pad_en`` parameter [int]
Supported on:
- - x86_64 with ConnectX-4, ConnectX-4 LX, ConnectX-5, ConnectX-6, ConnectX-6 DX
- and BlueField.
- - POWER8 and ARMv8 with ConnectX-4 LX, ConnectX-5, ConnectX-6, ConnectX-6 DX
- and BlueField.
+ - x86_64 with ConnectX-4, ConnectX-4 Lx, ConnectX-5, ConnectX-6, ConnectX-6 Dx,
+ ConnectX-6 Lx, BlueField and BlueField-2.
+ - POWER8 and ARMv8 with ConnectX-4 Lx, ConnectX-5, ConnectX-6, ConnectX-6 Dx,
+ ConnectX-6 Lx, BlueField and BlueField-2.
- ``mprq_en`` parameter [int]
A nonzero value enables configuring Multi-Packet Rx queues. Rx queue is
configured as Multi-Packet RQ if the total number of Rx queues is
- ``rxqs_min_mprq`` or more and Rx scatter isn't configured. Disabled by
- default.
+ ``rxqs_min_mprq`` or more. Disabled by default.
Multi-Packet Rx Queue (MPRQ a.k.a Striding RQ) can further save PCIe bandwidth
by posting a single large buffer for multiple packets. Instead of posting a
The size of Rx queue should be bigger than the number of strides.
+- ``mprq_log_stride_size`` parameter [int]
+
+ Log 2 of the size of a stride for Multi-Packet Rx queue. Configuring a smaller
+ stride size can save some memory and reduce probability of a depletion of all
+ available strides due to unreleased packets by an application. If configured
+ value is not in the range of device capability, the default value will be set
+ with a warning message. The default value is 11 which is 2048 bytes per a
+ stride, valid only if ``mprq_en`` is set. With ``mprq_log_stride_size`` set
+ it is possible for a packet to span across multiple strides. This mode allows
+ support of jumbo frames (9K) with MPRQ. The memcopy of some packets (or part
+ of a packet if Rx scatter is configured) may be required in case there is no
+ space left for a head room at the end of a stride which incurs some
+ performance penalty.
+
- ``mprq_max_memcpy_len`` parameter [int]
The maximum length of packet to memcpy in case of Multi-Packet Rx queue. Rx
the mbuf by external buffer attachment - ``rte_pktmbuf_attach_extbuf()``.
A mempool for external buffers will be allocated and managed by PMD. If Rx
packet is externally attached, ol_flags field of the mbuf will have
- EXT_ATTACHED_MBUF and this flag must be preserved. ``RTE_MBUF_HAS_EXTBUF()``
+ RTE_MBUF_F_EXTERNAL and this flag must be preserved. ``RTE_MBUF_HAS_EXTBUF()``
checks the flag. The default value is 128, valid only if ``mprq_en`` is set.
- ``rxqs_min_mprq`` parameter [int]
If ``txq_inline_min`` key is not present, the value may be queried by the
driver from the NIC via DevX if this feature is available. If there is no DevX
enabled/supported the value 18 (supposing L2 header including VLAN) is set
- for ConnectX-4 and ConnectX-4LX, and 0 is set by default for ConnectX-5
+ for ConnectX-4 and ConnectX-4 Lx, and 0 is set by default for ConnectX-5
and newer NICs. If packet is shorter the ``txq_inline_min`` value, the entire
packet is inlined.
For ConnectX-4 NIC, driver does not allow specifying value below 18
(minimal L2 header, including VLAN), error will be raised.
- For ConnectX-4LX NIC, it is allowed to specify values below 18, but
+ For ConnectX-4 Lx NIC, it is allowed to specify values below 18, but
it is not recommended and may prevent NIC from sending packets over
some configurations.
+ For ConnectX-4 and ConnectX-4 Lx NICs, automatically configured value
+ is insufficient for some traffic, because they require at least all L2 headers
+ to be inlined. For example, Q-in-Q adds 4 bytes to default 18 bytes
+ of Ethernet and VLAN, thus ``txq_inline_min`` must be set to 22.
+ MPLS would add 4 bytes per label. Final value must account for all possible
+ L2 encapsulation headers used in particular environment.
+
Please, note, this minimal data inlining disengages eMPW feature (Enhanced
Multi-Packet Write), because last one does not support partial packet inlining.
This is not very critical due to minimal data inlining is mostly required
- ``txq_mpw_en`` parameter [int]
A nonzero value enables Enhanced Multi-Packet Write (eMPW) for ConnectX-5,
- ConnectX-6, ConnectX-6 DX and BlueField. eMPW allows the TX burst function to pack
- up multiple packets in a single descriptor session in order to save PCI bandwidth
- and improve performance at the cost of a slightly higher CPU usage. When
- ``txq_inline_mpw`` is set along with ``txq_mpw_en``, TX burst function copies
- entire packet data on to TX descriptor instead of including pointer of packet.
+ ConnectX-6, ConnectX-6 Dx, ConnectX-6 Lx, BlueField, BlueField-2.
+ eMPW allows the Tx burst function to pack up multiple packets
+ in a single descriptor session in order to save PCI bandwidth
+ and improve performance at the cost of a slightly higher CPU usage.
+ When ``txq_inline_mpw`` is set along with ``txq_mpw_en``,
+ Tx burst function copies entire packet data on to Tx descriptor
+ instead of including pointer of packet.
The Enhanced Multi-Packet Write feature is enabled by default if NIC supports
it, can be disabled by explicit specifying 0 value for ``txq_mpw_en`` option.
variable "MLX5_SHUT_UP_BF" value is used. If there is no "MLX5_SHUT_UP_BF",
the default ``tx_db_nc`` value is zero for ARM64 hosts and one for others.
+- ``tx_pp`` parameter [int]
+
+ If a nonzero value is specified the driver creates all necessary internal
+ objects to provide accurate packet send scheduling on mbuf timestamps.
+ The positive value specifies the scheduling granularity in nanoseconds,
+ the packet send will be accurate up to specified digits. The allowed range is
+ from 500 to 1 million of nanoseconds. The negative value specifies the module
+ of granularity and engages the special test mode the check the schedule rate.
+ By default (if the ``tx_pp`` is not specified) send scheduling on timestamps
+ feature is disabled.
+
+- ``tx_skew`` parameter [int]
+
+ The parameter adjusts the send packet scheduling on timestamps and represents
+ the average delay between beginning of the transmitting descriptor processing
+ by the hardware and appearance of actual packet data on the wire. The value
+ should be provided in nanoseconds and is valid only if ``tx_pp`` parameter is
+ specified. The default value is zero.
+
- ``tx_vec_en`` parameter [int]
- A nonzero value enables Tx vector on ConnectX-5, ConnectX-6, ConnectX-6 DX
- and BlueField NICs if the number of global Tx queues on the port is less than
- ``txqs_max_vec``. The parameter is deprecated and ignored.
+ A nonzero value enables Tx vector on ConnectX-5, ConnectX-6, ConnectX-6 Dx,
+ ConnectX-6 Lx, BlueField and BlueField-2 NICs
+ if the number of global Tx queues on the port is less than ``txqs_max_vec``.
+ The parameter is deprecated and ignored.
- ``rx_vec_en`` parameter [int]
24 bits. The actual supported width can be retrieved in runtime by
series of rte_flow_validate() trials.
+ - 3, this engages tunnel offload mode. In E-Switch configuration, that
+ mode implicitly activates ``dv_xmeta_en=1``.
+
+------+-----------+-----------+-------------+-------------+
| Mode | ``MARK`` | ``META`` | ``META`` Tx | FDB/Through |
+======+===========+===========+=============+=============+
+------+-----------+-----------+-------------+-------------+
| 1 | 24 bits | vary 0-32 | 32 bits | yes |
+------+-----------+-----------+-------------+-------------+
- | 2 | vary 0-32 | 32 bits | 32 bits | yes |
+ | 2 | vary 0-24 | 32 bits | 32 bits | yes |
+------+-----------+-----------+-------------+-------------+
If there is no E-Switch configuration the ``dv_xmeta_en`` parameter is
of the extensive metadata features. The legacy Verbs supports FLAG and
MARK metadata actions over NIC Rx steering domain only.
+ Setting META value to zero in flow action means there is no item provided
+ and receiving datapath will not report in mbufs the metadata are present.
+ Setting MARK value to zero in flow action means the zero FDIR ID value
+ will be reported on packet receiving.
+
+ For the MARK action the last 16 values in the full range are reserved for
+ internal PMD purposes (to emulate FLAG action). The valid range for the
+ MARK action values is 0-0xFFEF for the 16-bit mode and 0-xFFFFEF
+ for the 24-bit mode, the flows with the MARK action value outside
+ the specified range will be rejected.
+
- ``dv_flow_en`` parameter [int]
A nonzero value enables the DV flow steering assuming it is supported
Enabled by default if supported.
+- ``lacp_by_user`` parameter [int]
+
+ A nonzero value enables the control of LACP traffic by the user application.
+ When a bond exists in the driver, by default it should be managed by the
+ kernel and therefore LACP traffic should be steered to the kernel.
+ If this devarg is set to 1 it will allow the user to manage the bond by
+ itself and not steer LACP traffic to the kernel.
+
+ Disabled by default (set to 0).
+
- ``mr_ext_memseg_en`` parameter [int]
A nonzero value enables extending memseg when registering DMA memory. If
- ``representor`` parameter [list]
This parameter can be used to instantiate DPDK Ethernet devices from
- existing port (or VF) representors configured on the device.
+ existing port (PF, VF or SF) representors configured on the device.
It is a standard parameter whose format is described in
:ref:`ethernet_device_standard_device_arguments`.
- For instance, to probe port representors 0 through 2::
+ For instance, to probe VF port representors 0 through 2::
+
+ <PCI_BDF>,representor=vf[0-2]
- representor=[0-2]
+ To probe SF port representors 0 through 2::
+
+ <PCI_BDF>,representor=sf[0-2]
+
+ To probe VF port representors 0 through 2 on both PFs of bonding device::
+
+ <Primary_PCI_BDF>,representor=pf[0,1]vf[0-2]
- ``max_dump_files_num`` parameter [int]
If this parameter is not specified, by default PMD will set
the smallest value supported by HW.
+- ``hp_buf_log_sz`` parameter [int]
+
+ The total data buffer size of a hairpin queue (logarithmic form), in bytes.
+ PMD will set the data buffer size to 2 ** ``hp_buf_log_sz``, both for RX & TX.
+ The capacity of the value is specified by the firmware and the initialization
+ will get a failure if it is out of scope.
+ The range of the value is from 11 to 19 right now, and the supported frame
+ size of a single packet for hairpin is from 512B to 128KB. It might change if
+ different firmware release is being used. By using a small value, it could
+ reduce memory consumption but not work with a large frame. If the value is
+ too large, the memory consumption will be high and some potential performance
+ degradation will be introduced.
+ By default, the PMD will set this value to 16, which means that 9KB jumbo
+ frames will be supported.
+
+- ``reclaim_mem_mode`` parameter [int]
+
+ Cache some resources in flow destroy will help flow recreation more efficient.
+ While some systems may require the all the resources can be reclaimed after
+ flow destroyed.
+ The parameter ``reclaim_mem_mode`` provides the option for user to configure
+ if the resource cache is needed or not.
+
+ There are three options to choose:
+
+ - 0. It means the flow resources will be cached as usual. The resources will
+ be cached, helpful with flow insertion rate.
+
+ - 1. It will only enable the DPDK PMD level resources reclaim.
+
+ - 2. Both DPDK PMD level and rdma-core low level will be configured as
+ reclaimed mode.
+
+ By default, the PMD will set this value to 0.
+
+- ``sys_mem_en`` parameter [int]
+
+ A non-zero value enables the PMD memory management allocating memory
+ from system by default, without explicit rte memory flag.
+
+ By default, the PMD will set this value to 0.
+
+- ``decap_en`` parameter [int]
+
+ Some devices do not support FCS (frame checksum) scattering for
+ tunnel-decapsulated packets.
+ If set to 0, this option forces the FCS feature and rejects tunnel
+ decapsulation in the flow engine for such devices.
+
+ By default, the PMD will set this value to 1.
+
+- ``allow_duplicate_pattern`` parameter [int]
+
+ There are two options to choose:
+
+ - 0. Prevent insertion of rules with the same pattern items on non-root table.
+ In this case, only the first rule is inserted and the following rules are
+ rejected and error code EEXIST is returned.
+
+ - 1. Allow insertion of rules with the same pattern items.
+ In this case, all rules are inserted but only the first rule takes effect,
+ the next rule takes effect only if the previous rules are deleted.
+
+ By default, the PMD will set this value to 1.
+
.. _mlx5_firmware_config:
Firmware configuration
IP_OVER_VXLAN_EN=1
IP_OVER_VXLAN_PORT=<udp dport>
+- enable VXLAN-GPE tunnel flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=0
+ or
+ FLEX_PARSER_PROFILE_ENABLE=2
+
- enable IP-in-IP tunnel flow matching::
FLEX_PARSER_PROFILE_ENABLE=0
FLEX_PARSER_PROFILE_ENABLE=1
-- enable ICMP/ICMP6 code/type fields matching::
+- enable ICMP(code/type/identifier/sequence number) / ICMP6(code/type) fields matching::
FLEX_PARSER_PROFILE_ENABLE=2
- enable Geneve flow matching::
FLEX_PARSER_PROFILE_ENABLE=0
+ or
+ FLEX_PARSER_PROFILE_ENABLE=1
+
+- enable Geneve TLV option flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=0
- enable GTP flow matching::
FLEX_PARSER_PROFILE_ENABLE=3
-Prerequisites
--------------
+- enable eCPRI flow matching::
+
+ FLEX_PARSER_PROFILE_ENABLE=4
+ PROG_PARSE_GRAPH=1
+
+Linux Prerequisites
+-------------------
This driver relies on external libraries and kernel drivers for resources
allocations and initialization. The following dependencies are not part of
- **libibverbs**
- User space Verbs framework used by librte_pmd_mlx5. This library provides
+ User space Verbs framework used by librte_net_mlx5. This library provides
a generic interface between the kernel and low-level user space drivers
such as libmlx5.
.. _`Linux installation documentation`: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable.git/plain/Documentation/admin-guide/README.rst
.. _`RDMA Core installation documentation`: https://raw.githubusercontent.com/linux-rdma/rdma-core/master/README.md
-If rdma-core libraries are built but not installed, DPDK makefile can link them,
-thanks to these environment variables:
-
- - ``EXTRA_CFLAGS=-I/path/to/rdma-core/build/include``
- - ``EXTRA_LDFLAGS=-L/path/to/rdma-core/build/lib``
- - ``PKG_CONFIG_PATH=/path/to/rdma-core/build/lib/pkgconfig``
Mellanox OFED/EN
^^^^^^^^^^^^^^^^
-- Mellanox OFED version: ** 4.5, 4.6** /
- Mellanox EN version: **4.5, 4.6**
+- Mellanox OFED version: **4.5** and above /
+ Mellanox EN version: **4.5** and above
- firmware version:
- ConnectX-4: **12.21.1000** and above.
- ConnectX-4 Lx: **14.21.1000** and above.
- ConnectX-5: **16.21.1000** and above.
- ConnectX-5 Ex: **16.21.1000** and above.
- - ConnectX-6: **20.99.5374** and above.
- - ConnectX-6 DX: **22.27.0090** and above.
+ - ConnectX-6: **20.27.0090** and above.
+ - ConnectX-6 Dx: **22.27.0090** and above.
- BlueField: **18.25.1010** and above.
While these libraries and kernel modules are available on OpenFabrics
Several versions of Mellanox OFED/EN are available. Installing the version
this DPDK release was developed and tested against is strongly
- recommended. Please check the `prerequisites`_.
+ recommended. Please check the `linux prerequisites`_.
+
+Windows Prerequisites
+---------------------
+
+This driver relies on external libraries and kernel drivers for resources
+allocations and initialization. The dependencies in the following sub-sections
+are not part of DPDK, and must be installed separately.
+
+Compilation Prerequisites
+~~~~~~~~~~~~~~~~~~~~~~~~~
+
+DevX SDK installation
+^^^^^^^^^^^^^^^^^^^^^
+
+The DevX SDK must be installed on the machine building the Windows PMD.
+Additional information can be found at
+`How to Integrate Windows DevX in Your Development Environment
+<https://docs.mellanox.com/display/winof2v250/RShim+Drivers+and+Usage#RShimDriversandUsage-DevXInterface>`__.
+
+Runtime Prerequisites
+~~~~~~~~~~~~~~~~~~~~~
+
+WinOF2 version 2.60 or higher must be installed on the machine.
+
+WinOF2 installation
+^^^^^^^^^^^^^^^^^^^
+
+The driver can be downloaded from the following site:
+`WINOF2
+<https://www.mellanox.com/products/adapter-software/ethernet/windows/winof-2>`__
+
+DevX Enablement
+^^^^^^^^^^^^^^^
+
+DevX for Windows must be enabled in the Windows registry.
+The keys ``DevxEnabled`` and ``DevxFsRules`` must be set.
+Additional information can be found in the WinOF2 user manual.
Supported NICs
--------------
-* Mellanox(R) ConnectX(R)-4 10G MCX4111A-XCAT (1x10G)
-* Mellanox(R) ConnectX(R)-4 10G MCX4121A-XCAT (2x10G)
-* Mellanox(R) ConnectX(R)-4 25G MCX4111A-ACAT (1x25G)
-* Mellanox(R) ConnectX(R)-4 25G MCX4121A-ACAT (2x25G)
-* Mellanox(R) ConnectX(R)-4 40G MCX4131A-BCAT (1x40G)
-* Mellanox(R) ConnectX(R)-4 40G MCX413A-BCAT (1x40G)
-* Mellanox(R) ConnectX(R)-4 40G MCX415A-BCAT (1x40G)
-* Mellanox(R) ConnectX(R)-4 50G MCX4131A-GCAT (1x50G)
-* Mellanox(R) ConnectX(R)-4 50G MCX413A-GCAT (1x50G)
-* Mellanox(R) ConnectX(R)-4 50G MCX414A-BCAT (2x50G)
-* Mellanox(R) ConnectX(R)-4 50G MCX415A-GCAT (2x50G)
-* Mellanox(R) ConnectX(R)-4 50G MCX416A-BCAT (2x50G)
-* Mellanox(R) ConnectX(R)-4 50G MCX416A-GCAT (2x50G)
-* Mellanox(R) ConnectX(R)-4 50G MCX415A-CCAT (1x100G)
-* Mellanox(R) ConnectX(R)-4 100G MCX416A-CCAT (2x100G)
-* Mellanox(R) ConnectX(R)-4 Lx 10G MCX4121A-XCAT (2x10G)
-* Mellanox(R) ConnectX(R)-4 Lx 25G MCX4121A-ACAT (2x25G)
-* Mellanox(R) ConnectX(R)-5 100G MCX556A-ECAT (2x100G)
-* Mellanox(R) ConnectX(R)-5 Ex EN 100G MCX516A-CDAT (2x100G)
-* Mellanox(R) ConnectX(R)-6 200G MCX654106A-HCAT (4x200G)
-* Mellanox(R) ConnectX(R)-6DX EN 100G MCX623106AN-CDAT (2*100g)
-* Mellanox(R) ConnectX(R)-6DX EN 200G MCX623105AN-VDAT (1*200g)
+The following Mellanox device families are supported by the same mlx5 driver:
+
+ - ConnectX-4
+ - ConnectX-4 Lx
+ - ConnectX-5
+ - ConnectX-5 Ex
+ - ConnectX-6
+ - ConnectX-6 Dx
+ - ConnectX-6 Lx
+ - BlueField
+ - BlueField-2
+
+Below are detailed device names:
+
+* Mellanox\ |reg| ConnectX\ |reg|-4 10G MCX4111A-XCAT (1x10G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 10G MCX412A-XCAT (2x10G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 25G MCX4111A-ACAT (1x25G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 25G MCX412A-ACAT (2x25G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 40G MCX413A-BCAT (1x40G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 40G MCX4131A-BCAT (1x40G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 40G MCX415A-BCAT (1x40G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX413A-GCAT (1x50G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX4131A-GCAT (1x50G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX414A-BCAT (2x50G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX415A-GCAT (1x50G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX416A-BCAT (2x50G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX416A-GCAT (2x50G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 50G MCX415A-CCAT (1x100G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 100G MCX416A-CCAT (2x100G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 Lx 10G MCX4111A-XCAT (1x10G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 Lx 10G MCX4121A-XCAT (2x10G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 Lx 25G MCX4111A-ACAT (1x25G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 Lx 25G MCX4121A-ACAT (2x25G)
+* Mellanox\ |reg| ConnectX\ |reg|-4 Lx 40G MCX4131A-BCAT (1x40G)
+* Mellanox\ |reg| ConnectX\ |reg|-5 100G MCX556A-ECAT (2x100G)
+* Mellanox\ |reg| ConnectX\ |reg|-5 Ex EN 100G MCX516A-CDAT (2x100G)
+* Mellanox\ |reg| ConnectX\ |reg|-6 200G MCX654106A-HCAT (2x200G)
+* Mellanox\ |reg| ConnectX\ |reg|-6 Dx EN 100G MCX623106AN-CDAT (2x100G)
+* Mellanox\ |reg| ConnectX\ |reg|-6 Dx EN 200G MCX623105AN-VDAT (1x200G)
+* Mellanox\ |reg| ConnectX\ |reg|-6 Lx EN 25G MCX631102AN-ADAT (2x25G)
Quick Start Guide on OFED/EN
----------------------------
-1. Download latest Mellanox OFED/EN. For more info check the `prerequisites`_.
+1. Download latest Mellanox OFED/EN. For more info check the `linux prerequisites`_.
2. Install the required libraries and kernel modules either by installing
echo [num_vfs] > /sys/class/infiniband/mlx5_0/device/sriov_numvfs
-6. Compile DPDK and you are ready to go. See instructions on
- :ref:`Development Kit Build System <Development_Kit_Build_System>`
+6. Install DPDK and you are ready to go.
+ See :doc:`compilation instructions <../linux_gsg/build_dpdk>`.
Enable switchdev mode
---------------------
-Switchdev mode is a mode in E-Switch, that binds between representor and VF.
-Representor is a port in DPDK that is connected to a VF in such a way
-that assuming there are no offload flows, each packet that is sent from the VF
-will be received by the corresponding representor. While each packet that is
-sent to a representor will be received by the VF.
+Switchdev mode is a mode in E-Switch, that binds between representor and VF or SF.
+Representor is a port in DPDK that is connected to a VF or SF in such a way
+that assuming there are no offload flows, each packet that is sent from the VF or SF
+will be received by the corresponding representor. While each packet that is or SF
+sent to a representor will be received by the VF or SF.
This is very useful in case of SRIOV mode, where the first packet that is sent
-by the VF will be received by the DPDK application which will decide if this
+by the VF or SF will be received by the DPDK application which will decide if this
flow should be offloaded to the E-Switch. After offloading the flow packet
-that the VF that are matching the flow will not be received any more by
+that the VF or SF that are matching the flow will not be received any more by
the DPDK application.
1. Enable SRIOV mode::
echo switchdev > /sys/class/net/<net device>/compat/devlink/mode
+Sub-Function support
+--------------------
+
+Sub-Function is a portion of the PCI device, a SF netdev has its own
+dedicated queues (txq, rxq).
+A SF shares PCI level resources with other SFs and/or with its parent PCI function.
+
+0. Requirement::
+
+ OFED version >= 5.4-0.3.3.0
+
+1. Configure SF feature::
+
+ # Run mlxconfig on both PFs on host and ECPFs on BlueField.
+ mlxconfig -d <mst device> set PER_PF_NUM_SF=1 PF_TOTAL_SF=252 PF_SF_BAR_SIZE=12
+
+2. Enable switchdev mode::
+
+ mlxdevm dev eswitch set pci/<DBDF> mode switchdev
+
+3. Add SF port::
+
+ mlxdevm port add pci/<DBDF> flavour pcisf pfnum 0 sfnum <sfnum>
+
+ Get SFID from output: pci/<DBDF>/<SFID>
+
+4. Modify MAC address::
+
+ mlxdevm port function set pci/<DBDF>/<SFID> hw_addr <MAC>
+
+5. Activate SF port::
+
+ mlxdevm port function set pci/<DBDF>/<ID> state active
+
+6. Devargs to probe SF device::
+
+ auxiliary:mlx5_core.sf.<num>,dv_flow_en=1
+
+Sub-Function representor support
+--------------------------------
+
+A SF netdev supports E-Switch representation offload
+similar to PF and VF representors.
+Use <sfnum> to probe SF representor::
+
+ testpmd> port attach <PCI_BDF>,representor=sf<sfnum>,dv_flow_en=1
+
Performance tuning
------------------
for better performance. For VMs, verify that the right CPU
and NUMA node are pinned according to the above. Run::
- lstopo-no-graphics
+ lstopo-no-graphics --merge
to identify the NUMA node to which the PCIe adapter is connected.
- Configure per-lcore cache when creating Mempools for packet buffer.
- Refrain from dynamically allocating/freeing memory in run-time.
+Rx burst functions
+------------------
+
+There are multiple Rx burst functions with different advantages and limitations.
+
+.. table:: Rx burst functions
+
+ +-------------------+------------------------+---------+-----------------+------+-------+
+ || Function Name || Enabler || Scatter|| Error Recovery || CQE || Large|
+ | | | | || comp|| MTU |
+ +===================+========================+=========+=================+======+=======+
+ | rx_burst | rx_vec_en=0 | Yes | Yes | Yes | Yes |
+ +-------------------+------------------------+---------+-----------------+------+-------+
+ | rx_burst_vec | rx_vec_en=1 (default) | No | if CQE comp off | Yes | No |
+ +-------------------+------------------------+---------+-----------------+------+-------+
+ | rx_burst_mprq || mprq_en=1 | No | Yes | Yes | Yes |
+ | || RxQs >= rxqs_min_mprq | | | | |
+ +-------------------+------------------------+---------+-----------------+------+-------+
+ | rx_burst_mprq_vec || rx_vec_en=1 (default) | No | if CQE comp off | Yes | Yes |
+ | || mprq_en=1 | | | | |
+ | || RxQs >= rxqs_min_mprq | | | | |
+ +-------------------+------------------------+---------+-----------------+------+-------+
+
.. _mlx5_offloads_support:
Supported hardware offloads
.. table:: Minimal SW/HW versions for queue offloads
- ============== ===== ===== ========= ===== ========== ==========
+ ============== ===== ===== ========= ===== ========== =============
Offload DPDK Linux rdma-core OFED firmware hardware
- ============== ===== ===== ========= ===== ========== ==========
+ ============== ===== ===== ========= ===== ========== =============
common base 17.11 4.14 16 4.2-1 12.21.1000 ConnectX-4
checksums 17.11 4.14 16 4.2-1 12.21.1000 ConnectX-4
Rx timestamp 17.11 4.14 16 4.2-1 12.21.1000 ConnectX-4
TSO 17.11 4.14 16 4.2-1 12.21.1000 ConnectX-4
LRO 19.08 N/A N/A 4.6-4 16.25.6406 ConnectX-5
- ============== ===== ===== ========= ===== ========== ==========
+ Tx scheduling 20.08 N/A N/A 5.1-2 22.28.2006 ConnectX-6 Dx
+ Buffer Split 20.11 N/A N/A 5.1-2 16.28.2006 ConnectX-5
+ ============== ===== ===== ========= ===== ========== =============
.. table:: Minimal SW/HW versions for rte_flow offloads
| | | | | rdma-core 23 |
| | | | | ConnectX-4 |
+-----------------------+-----------------+-----------------+
+ | Shared action | | | | |
+ | | | :numref:`sact`| | :numref:`sact`|
+ | | | | | |
+ | | | | | |
+ +-----------------------+-----------------+-----------------+
+ | | VLAN | | DPDK 19.11 | | DPDK 19.11 |
+ | | (of_pop_vlan / | | OFED 4.7-1 | | OFED 4.7-1 |
+ | | of_push_vlan / | | ConnectX-5 | | ConnectX-5 |
+ | | of_set_vlan_pcp / | | | | |
+ | | of_set_vlan_vid) | | | | |
+ +-----------------------+-----------------+-----------------+
+ | | VLAN | | DPDK 21.05 | | |
+ | | ingress and / | | OFED 5.3 | | N/A |
+ | | of_push_vlan / | | ConnectX-6 Dx | | |
+ +-----------------------+-----------------+-----------------+
+ | | VLAN | | DPDK 21.05 | | |
+ | | egress and / | | OFED 5.3 | | N/A |
+ | | of_pop_vlan / | | ConnectX-6 Dx | | |
+ +-----------------------+-----------------+-----------------+
| Encapsulation | | DPDK 19.05 | | DPDK 19.02 |
| (VXLAN / NVGRE / RAW) | | OFED 4.7-1 | | OFED 4.6 |
| | | rdma-core 24 | | rdma-core 23 |
| | | rdma-core 27 | | rdma-core 27 |
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
+ | Tunnel Offload | | DPDK 20.11 | | DPDK 20.11 |
+ | | | OFED 5.1-2 | | OFED 5.1-2 |
+ | | | rdma-core 32 | | N/A |
+ | | | ConnectX-5 | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
| | Header rewrite | | DPDK 19.05 | | DPDK 19.02 |
| | (set_ipv4_src / | | OFED 4.7-1 | | OFED 4.7-1 |
| | set_ipv4_dst / | | rdma-core 24 | | rdma-core 24 |
| | | rdma-core 24 | | rdma-core 23 |
| | | ConnectX-5 | | ConnectX-4 |
+-----------------------+-----------------+-----------------+
+ | Meta data | | DPDK 19.11 | | DPDK 19.11 |
+ | | | OFED 4.7-3 | | OFED 4.7-3 |
+ | | | rdma-core 26 | | rdma-core 26 |
+ | | | ConnectX-5 | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
| Port ID | | DPDK 19.05 | | N/A |
| | | OFED 4.7-1 | | N/A |
| | | rdma-core 24 | | N/A |
| | | ConnectX-5 | | N/A |
+-----------------------+-----------------+-----------------+
- | | VLAN | | DPDK 19.11 | | DPDK 19.11 |
- | | (of_pop_vlan / | | OFED 4.7-1 | | OFED 4.7-1 |
- | | of_push_vlan / | | ConnectX-5 | | ConnectX-5 |
- | | of_set_vlan_pcp / | | | | |
- | | of_set_vlan_vid) | | | | |
- +-----------------------+-----------------+-----------------+
| Hairpin | | | | DPDK 19.11 |
| | | N/A | | OFED 4.7-3 |
| | | | | rdma-core 26 |
| | | | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
- | Meta data | | DPDK 19.11 | | DPDK 19.11 |
- | | | OFED 4.7-3 | | OFED 4.7-3 |
- | | | rdma-core 26 | | rdma-core 26 |
- | | | ConnectX-5 | | ConnectX-5 |
+ | 2-port Hairpin | | | | DPDK 20.11 |
+ | | | N/A | | OFED 5.1-2 |
+ | | | | | N/A |
+ | | | | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
| Metering | | DPDK 19.11 | | DPDK 19.11 |
| | | OFED 4.7-3 | | OFED 4.7-3 |
| | | rdma-core 26 | | rdma-core 26 |
| | | ConnectX-5 | | ConnectX-5 |
+-----------------------+-----------------+-----------------+
+ | Sampling | | DPDK 20.11 | | DPDK 20.11 |
+ | | | OFED 5.1-2 | | OFED 5.1-2 |
+ | | | rdma-core 32 | | N/A |
+ | | | ConnectX-5 | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
+ | Encapsulation | | DPDK 21.02 | | DPDK 21.02 |
+ | GTP PSC | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 35 | | rdma-core 35 |
+ | | | ConnectX-6 Dx| | ConnectX-6 Dx |
+ +-----------------------+-----------------+-----------------+
+ | Encapsulation | | DPDK 21.02 | | DPDK 21.02 |
+ | GENEVE TLV option | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 34 | | rdma-core 34 |
+ | | | ConnectX-6 Dx | | ConnectX-6 Dx |
+ +-----------------------+-----------------+-----------------+
+ | Modify Field | | DPDK 21.02 | | DPDK 21.02 |
+ | | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 35 | | rdma-core 35 |
+ | | | ConnectX-5 | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
+ | Connection tracking | | | | DPDK 21.05 |
+ | | | N/A | | OFED 5.3 |
+ | | | | | rdma-core 35 |
+ | | | | | ConnectX-6 Dx |
+ +-----------------------+-----------------+-----------------+
+
+.. table:: Minimal SW/HW versions for shared action offload
+ :name: sact
+
+ +-----------------------+-----------------+-----------------+
+ | Shared Action | with E-Switch | with NIC |
+ +=======================+=================+=================+
+ | RSS | | | | DPDK 20.11 |
+ | | | N/A | | OFED 5.2 |
+ | | | | | rdma-core 33 |
+ | | | | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
+ | Age | | DPDK 20.11 | | DPDK 20.11 |
+ | | | OFED 5.2 | | OFED 5.2 |
+ | | | rdma-core 32 | | rdma-core 32 |
+ | | | ConnectX-6 Dx | | ConnectX-6 Dx |
+ +-----------------------+-----------------+-----------------+
+ | Count | | DPDK 21.05 | | DPDK 21.05 |
+ | | | OFED 4.6 | | OFED 4.6 |
+ | | | rdma-core 24 | | rdma-core 23 |
+ | | | ConnectX-5 | | ConnectX-5 |
+ +-----------------------+-----------------+-----------------+
+
+Notes for metadata
+------------------
+
+MARK and META items are interrelated with datapath - they might move from/to
+the applications in mbuf fields. Hence, zero value for these items has the
+special meaning - it means "no metadata are provided", not zero values are
+treated by applications and PMD as valid ones.
+
+Moreover in the flow engine domain the value zero is acceptable to match and
+set, and we should allow to specify zero values as rte_flow parameters for the
+META and MARK items and actions. In the same time zero mask has no meaning and
+should be rejected on validation stage.
+
+Notes for rte_flow
+------------------
+
+Flows are not cached in the driver.
+When stopping a device port, all the flows created on this port from the
+application will be flushed automatically in the background.
+After stopping the device port, all flows on this port become invalid and
+not represented in the system.
+All references to these flows held by the application should be discarded
+directly but neither destroyed nor flushed.
+
+The application should re-create the flows as required after the port restart.
Notes for testpmd
-----------------
-Compared to librte_pmd_mlx4 that implements a single RSS configuration per
-port, librte_pmd_mlx5 supports per-protocol RSS configuration.
+Compared to librte_net_mlx4 that implements a single RSS configuration per
+port, librte_net_mlx5 supports per-protocol RSS configuration.
Since ``testpmd`` defaults to IP RSS mode and there is currently no
command-line parameter to enable additional protocols (UDP and TCP as well
as IP), the following commands must be entered from its CLI to get the same
-behavior as librte_pmd_mlx4::
+behavior as librte_net_mlx4::
> port stop all
> port config all rss all
-------------
This section demonstrates how to launch **testpmd** with Mellanox
-ConnectX-4/ConnectX-5/ConnectX-6/BlueField devices managed by librte_pmd_mlx5.
+ConnectX-4/ConnectX-5/ConnectX-6/BlueField devices managed by librte_net_mlx5.
#. Load the kernel modules::
eth32
eth33
-#. Optionally, retrieve their PCI bus addresses for whitelisting::
+#. Optionally, retrieve their PCI bus addresses for to be used with the allow list::
{
for intf in eth2 eth3 eth4 eth5;
(cd "/sys/class/net/${intf}/device/" && pwd -P);
done;
} |
- sed -n 's,.*/\(.*\),-w \1,p'
+ sed -n 's,.*/\(.*\),-a \1,p'
Example output::
- -w 0000:05:00.1
- -w 0000:06:00.0
- -w 0000:06:00.1
- -w 0000:05:00.0
+ -a 0000:05:00.1
+ -a 0000:06:00.0
+ -a 0000:06:00.1
+ -a 0000:05:00.0
#. Request huge pages::
- echo 1024 > /sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages/nr_hugepages
+ dpdk-hugepages.py --setup 2G
#. Start testpmd with basic parameters::
- testpmd -l 8-15 -n 4 -w 05:00.0 -w 05:00.1 -w 06:00.0 -w 06:00.1 -- --rxq=2 --txq=2 -i
+ dpdk-testpmd -l 8-15 -n 4 -a 05:00.0 -a 05:00.1 -a 06:00.0 -a 06:00.1 -- --rxq=2 --txq=2 -i
Example output::
[...]
EAL: PCI device 0000:05:00.0 on NUMA socket 0
- EAL: probe driver: 15b3:1013 librte_pmd_mlx5
- PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_0" (VF: false)
- PMD: librte_pmd_mlx5: 1 port(s) detected
- PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fe
+ EAL: probe driver: 15b3:1013 librte_net_mlx5
+ PMD: librte_net_mlx5: PCI information matches, using device "mlx5_0" (VF: false)
+ PMD: librte_net_mlx5: 1 port(s) detected
+ PMD: librte_net_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fe
EAL: PCI device 0000:05:00.1 on NUMA socket 0
- EAL: probe driver: 15b3:1013 librte_pmd_mlx5
- PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_1" (VF: false)
- PMD: librte_pmd_mlx5: 1 port(s) detected
- PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:ff
+ EAL: probe driver: 15b3:1013 librte_net_mlx5
+ PMD: librte_net_mlx5: PCI information matches, using device "mlx5_1" (VF: false)
+ PMD: librte_net_mlx5: 1 port(s) detected
+ PMD: librte_net_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:ff
EAL: PCI device 0000:06:00.0 on NUMA socket 0
- EAL: probe driver: 15b3:1013 librte_pmd_mlx5
- PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_2" (VF: false)
- PMD: librte_pmd_mlx5: 1 port(s) detected
- PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fa
+ EAL: probe driver: 15b3:1013 librte_net_mlx5
+ PMD: librte_net_mlx5: PCI information matches, using device "mlx5_2" (VF: false)
+ PMD: librte_net_mlx5: 1 port(s) detected
+ PMD: librte_net_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fa
EAL: PCI device 0000:06:00.1 on NUMA socket 0
- EAL: probe driver: 15b3:1013 librte_pmd_mlx5
- PMD: librte_pmd_mlx5: PCI information matches, using device "mlx5_3" (VF: false)
- PMD: librte_pmd_mlx5: 1 port(s) detected
- PMD: librte_pmd_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fb
+ EAL: probe driver: 15b3:1013 librte_net_mlx5
+ PMD: librte_net_mlx5: PCI information matches, using device "mlx5_3" (VF: false)
+ PMD: librte_net_mlx5: 1 port(s) detected
+ PMD: librte_net_mlx5: port 1 MAC address is e4:1d:2d:e7:0c:fb
Interactive-mode selected
Configuring Port 0 (socket 0)
- PMD: librte_pmd_mlx5: 0x8cba80: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx5: 0x8cba80: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8cba80: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8cba80: RX queues number update: 0 -> 2
Port 0: E4:1D:2D:E7:0C:FE
Configuring Port 1 (socket 0)
- PMD: librte_pmd_mlx5: 0x8ccac8: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx5: 0x8ccac8: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8ccac8: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8ccac8: RX queues number update: 0 -> 2
Port 1: E4:1D:2D:E7:0C:FF
Configuring Port 2 (socket 0)
- PMD: librte_pmd_mlx5: 0x8cdb10: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx5: 0x8cdb10: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8cdb10: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8cdb10: RX queues number update: 0 -> 2
Port 2: E4:1D:2D:E7:0C:FA
Configuring Port 3 (socket 0)
- PMD: librte_pmd_mlx5: 0x8ceb58: TX queues number update: 0 -> 2
- PMD: librte_pmd_mlx5: 0x8ceb58: RX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8ceb58: TX queues number update: 0 -> 2
+ PMD: librte_net_mlx5: 0x8ceb58: RX queues number update: 0 -> 2
Port 3: E4:1D:2D:E7:0C:FB
Checking link statuses...
Port 0 Link Up - speed 40000 Mbps - full-duplex
.. code-block:: console
- testpmd> flow dump <port> <output_file>
+ To dump all flows:
+ testpmd> flow dump <port> all <output_file>
+ and dump one flow:
+ testpmd> flow dump <port> rule <rule_id> <output_file>
- call rte_flow_dev_dump api:
.. code-block:: console
- rte_flow_dev_dump(port, file, NULL);
+ rte_flow_dev_dump(port, flow, file, NULL);
#. Dump human-readable flows from raw file:
.. code-block:: console
- mlx_steering_dump.py -f <output_file>
+ mlx_steering_dump.py -f <output_file> -flowptr <flow_ptr>
+
+How to share a meter between ports in the same switch domain
+------------------------------------------------------------
+
+This section demonstrates how to use the shared meter. A meter M can be created
+on port X and to be shared with a port Y on the same switch domain by the next way:
+
+.. code-block:: console
+
+ flow create X ingress transfer pattern eth / port_id id is Y / end actions meter mtr_id M / end
+
+How to use meter hierarchy
+--------------------------
+
+This section demonstrates how to create and use a meter hierarchy.
+A termination meter M can be the policy green action of another termination meter N.
+The two meters are chained together as a chain. Using meter N in a flow will apply
+both the meters in hierarchy on that flow.
+
+.. code-block:: console
+
+ add port meter policy 0 1 g_actions queue index 0 / end y_actions end r_actions drop / end
+ create port meter 0 M 1 1 yes 0xffff 1 0
+ add port meter policy 0 2 g_actions meter mtr_id M / end y_actions end r_actions drop / end
+ create port meter 0 N 2 2 yes 0xffff 1 0
+ flow create 0 ingress group 1 pattern eth / end actions meter mtr_id N / end
git.droids-corp.org / dpdk.git / blobdiff