- Support for multiple rte_flow groups.
- Per packet no-inline hint flag to disable packet data copying into Tx descriptors.
- Hardware LRO.
+- Hairpin.
Limitations
-----------
Will match any ipv4 packet (VLAN included).
+- When using DV flow engine (``dv_flow_en`` = 1), flow pattern without VLAN item
+ will match untagged packets only.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / ipv4 / end ...
+
+ Will match untagged packets only.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / vlan / ipv4 / end ...
+
+ Will match tagged packets only, with any VLAN ID value.
+ The flow rule::
+
+ flow create 0 ingress pattern eth / vlan vid is 3 / ipv4 / end ...
+
+ Will only match tagged packets with VLAN ID 3.
+
- VLAN pop offload command:
- Flow rules having a VLAN pop offload command as one of their actions and
- Match on GTP tunnel header item supports the following fields only:
+ - v_pt_rsv_flags: E flag, S flag, PN flag
- msg_type
- teid
TCP header (122B).
- Rx queue with LRO offload enabled, receiving a non-LRO packet, can forward
it with size limited to max LRO size, not to max RX packet length.
+ - LRO can be used with outer header of TCP packets of the standard format:
+ eth (with or without vlan) / ipv4 or ipv6 / tcp / payload
+
+ Other TCP packets (e.g. with MPLS label) received on Rx queue with LRO enabled, will be received with bad checksum.
Statistics
----------
- **ethtool** operations on related kernel interfaces also affect the PMD.
+Run as non-root
+^^^^^^^^^^^^^^^
+
+In order to run as a non-root user,
+some capabilities must be granted to the application::
+
+ setcap cap_sys_admin,cap_net_admin,cap_net_raw,cap_ipc_lock+ep <dpdk-app>
+
+Below are the reasons of the need for each capability:
+
+``cap_sys_admin``
+ When using physical addresses (PA mode), with Linux >= 4.0,
+ for access to ``/proc/self/pagemap``.
+
+``cap_net_admin``
+ For device configuration.
+
+``cap_net_raw``
+ For raw ethernet queue allocation through kernel driver.
+
+``cap_ipc_lock``
+ For DMA memory pinning.
+
+Driver options
+^^^^^^^^^^^^^^
+
- ``rxq_cqe_comp_en`` parameter [int]
A nonzero value enables the compression of CQE on RX side. This feature
A nonzero value enables configuring Multi-Packet Rx queues. Rx queue is
configured as Multi-Packet RQ if the total number of Rx queues is
- ``rxqs_min_mprq`` or more and Rx scatter isn't configured. Disabled by
- default.
+ ``rxqs_min_mprq`` or more. Disabled by default.
Multi-Packet Rx Queue (MPRQ a.k.a Striding RQ) can further save PCIe bandwidth
by posting a single large buffer for multiple packets. Instead of posting a
The size of Rx queue should be bigger than the number of strides.
+- ``mprq_log_stride_size`` parameter [int]
+
+ Log 2 of the size of a stride for Multi-Packet Rx queue. Configuring a smaller
+ stride size can save some memory and reduce probability of a depletion of all
+ available strides due to unreleased packets by an application. If configured
+ value is not in the range of device capability, the default value will be set
+ with a warning message. The default value is 11 which is 2048 bytes per a
+ stride, valid only if ``mprq_en`` is set. With ``mprq_log_stride_size`` set
+ it is possible for a pcaket to span across multiple strides. This mode allows
+ support of jumbo frames (9K) with MPRQ. The memcopy of some packets (or part
+ of a packet if Rx scatter is configured) may be required in case there is no
+ space left for a head room at the end of a stride which incurs some
+ performance penalty.
+
- ``mprq_max_memcpy_len`` parameter [int]
The maximum length of packet to memcpy in case of Multi-Packet Rx queue. Rx
If this parameter is not specified, by default PMD will set
the smallest value supported by HW.
+- ``hp_buf_log_sz`` parameter [int]
+
+ The total data buffer size of a hairpin queue (logarithmic form), in bytes.
+ PMD will set the data buffer size to 2 ** ``hp_buf_log_sz``, both for RX & TX.
+ The capacity of the value is specified by the firmware and the initialization
+ will get a failure if it is out of scope.
+ The range of the value is from 11 to 19 right now, and the supported frame
+ size of a single packet for hairpin is from 512B to 128KB. It might change if
+ different firmware release is being used. By using a small value, it could
+ reduce memory consumption but not work with a large frame. If the value is
+ too large, the memory consumption will be high and some potential performance
+ degradation will be introduced.
+ By default, the PMD will set this value to 16, which means that 9KB jumbo
+ frames will be supported.
+
.. _mlx5_firmware_config:
Firmware configuration
META and MARK items and actions. In the same time zero mask has no meaning and
should be rejected on validation stage.
+Notes for rte_flow
+------------------
+
+Flows are not cached in the driver.
+When stopping a device port, all the flows created on this port from the
+application will be flushed automatically in the background.
+After stopping the device port, all flows on this port become invalid and
+not represented in the system.
+All references to these flows held by the application should be discarded
+directly but neither destroyed nor flushed.
+
+The application should re-create the flows as required after the port restart.
+
Notes for testpmd
-----------------
git.droids-corp.org / dpdk.git / blobdiff