.. SPDX-License-Identifier: BSD-3-Clause
- Copyright(c) 2019-2020 Xilinx, Inc.
+ Copyright(c) 2019-2021 Xilinx, Inc.
Copyright(c) 2016-2019 Solarflare Communications Inc.
This software was jointly developed between OKTET Labs (under contract
Solarflare libefx-based Poll Mode Driver
========================================
-The SFC EFX PMD (**librte_pmd_sfc_efx**) provides poll mode driver support
-for **Solarflare SFN7xxx and SFN8xxx** family of 10/40 Gbps adapters and
-**Solarflare XtremeScale X2xxx** family of 10/25/40/50/100 Gbps adapters.
+The SFC EFX PMD (**librte_net_sfc_efx**) provides poll mode driver support
+for **Solarflare SFN7xxx and SFN8xxx** family of 10/40 Gbps adapters,
+**Solarflare XtremeScale X2xxx** family of 10/25/40/50/100 Gbps adapters and
+**Alveo SN1000 SmartNICs** family of 10/25/40/50/100 Gbps adapters.
SFC EFX PMD has support for the latest Linux and FreeBSD operating systems.
More information can be found at `Solarflare Communications website
- SR-IOV PF
+- Port representors (see :ref: switch_representation)
+
Non-supported Features
----------------------
Supported attributes:
- Ingress
+- Transfer
-Supported pattern items:
+Supported pattern items (***non-transfer*** rules):
- VOID
- NVGRE (exact match of virtual subnet ID)
-Supported actions:
+Supported actions (***non-transfer*** rules):
- VOID
- MARK (supported only with ef10_essb Rx datapath)
+Supported pattern items (***transfer*** rules):
+
+- PORT_REPRESENTOR (cannot repeat; conflicts with other traffic source items)
+
+- REPRESENTED_PORT (cannot repeat; conflicts with other traffic source items)
+
+- PORT_ID (cannot repeat; conflicts with other traffic source items)
+
+- PHY_PORT (cannot repeat; conflicts with other traffic source items)
+
+- PF (cannot repeat; conflicts with other traffic source items)
+
+- VF (cannot repeat; conflicts with other traffic source items)
+
+- ETH
+
+- VLAN (double-tagging is supported)
+
+- IPV4 (source/destination addresses, IP transport protocol,
+ type of service, time to live)
+
+- IPV6 (source/destination addresses, IP transport protocol,
+ traffic class, hop limit)
+
+- TCP (source/destination ports, TCP header length + TCP flags)
+
+- UDP (source/destination ports)
+
+- VXLAN (exact match of VXLAN network identifier)
+
+- GENEVE (exact match of virtual network identifier)
+
+- NVGRE (exact match of virtual subnet ID)
+
+Supported actions (***transfer*** rules):
+
+- OF_POP_VLAN
+
+- OF_PUSH_VLAN
+
+- OF_VLAN_SET_VID
+
+- OF_VLAN_SET_PCP
+
+- SET_MAC_DST
+
+- SET_MAC_SRC
+
+- OF_DEC_NW_TTL
+
+- DEC_TTL
+
+- VXLAN_DECAP
+
+- VXLAN_ENCAP
+
+- FLAG
+
+- MARK
+
+- PHY_PORT
+
+- PF
+
+- VF
+
+- PORT_REPRESENTOR
+
+- REPRESENTED_PORT
+
+- PORT_ID
+
+- COUNT
+
+- DROP
+
Validating flow rules depends on the firmware variant.
The :ref:`flow_isolated_mode` is supported.
+The implementation is natively thread-safe.
+
Ethernet destination individual/group match
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Supported NICs
--------------
+- Xilinx Adapters:
+
+ - Alveo SN1022 SmartNIC
+
- Solarflare XtremeScale Adapters:
- Solarflare X2522 Dual Port SFP28 10/25GbE Adapter
~~~~~~~~~~~~~~~~~~~~~
The following per-device parameters can be passed via EAL PCI device
-whitelist option like "-w 02:00.0,arg1=value1,...".
+allow option like "-a 02:00.0,arg1=value1,...".
Case-insensitive 1/y/yes/on or 0/n/no/off may be used to specify
boolean parameters value.
+- ``class`` [net|vdpa] (default **net**)
+
+ Choose the mode of operation of ef100 device.
+ **net** device will work as network device and will be probed by net/sfc driver.
+ **vdpa** device will work as vdpa device and will be probed by vdpa/sfc driver.
+ If this parameter is not specified then ef100 device will operate as
+ network device.
+
+- ``switch_mode`` [legacy|switchdev] (see below for default)
+
+ In legacy mode, NIC firmware provides Ethernet virtual bridging (EVB) API
+ to configure switching inside NIC to deliver traffic to physical (PF) and
+ virtual (VF) PCI functions. PF driver is responsible to build the
+ infrastructure for VFs, and traffic goes to/from VF by default in accordance
+ with MAC address assigned, permissions and filters installed by VF drivers.
+ In switchdev mode VF traffic goes via port representor (if any) on PF, and
+ software virtual switch (for example, Open vSwitch) makes the decision.
+ Software virtual switch may install MAE rules to pass established traffic
+ flows via hardware and offload software datapath as the result.
+ Default is legacy, unless representors are specified, in which case switchdev
+ is chosen.
+
+- ``representor`` parameter [list]
+
+ Instantiate port representor Ethernet devices for specified Virtual
+ Functions list.
+
+ It is a standard parameter whose format is described in
+ :ref:`ethernet_device_standard_device_arguments`.
+
- ``rx_datapath`` [auto|efx|ef10|ef10_essb] (default **auto**)
Choose receive datapath implementation.
**ef10_simple** chooses EF10 (SFN7xxx, SFN8xxx, X2xxx) native datapath which
is even more faster then **ef10** but does not support multi-segment
mbufs, disallows multiple mempools and neglects mbuf reference counters.
- **ef100** chooses EF100 native datapath which does not support
- any offloads except multi-segment mbufs.
+ **ef100** chooses EF100 native datapath which supports multi-segment
+ mbufs, VLAN insertion, inner/outer IPv4 and TCP/UDP checksum and TCP
+ segmentation offloads including VXLAN and GENEVE IPv4/IPv6 tunnels.
- ``perf_profile`` [auto|throughput|low-latency] (default **throughput**)
- ``fw_variant`` [dont-care|full-feature|ultra-low-latency|
capture-packed-stream|dpdk] (default **dont-care**)
- Choose the preferred firmware variant to use. In order for the selected
- option to have an effect, the **sfboot** utility must be configured with the
- **auto** firmware-variant option. The preferred firmware variant applies to
- all ports on the NIC.
+ Choose the preferred firmware variant to use.
+ The parameter is supported for SFN7xxX, SFN8xxx and X2xxx families only.
+ In order for the selected option to have an effect, the **sfboot** utility
+ must be configured with the **auto** firmware-variant option.
+ The preferred firmware variant applies to all ports on the NIC.
**dont-care** ensures that the driver can attach to an unprivileged function.
The datapath firmware type to use is controlled by the **sfboot**
utility.
git.droids-corp.org / dpdk.git / blobdiff