app/testpmd: parse flow command line for AH

[dpdk.git] / doc / guides / testpmd_app_ug / testpmd_funcs.rst

diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
index 3baaacb..95f4f06 100644 (file)
--- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
+++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
@@ -2317,6 +2317,16 @@ testpmd will add this value to any Tx packet sent from this port::
 
    testpmd> port config (port_id) tx_metadata (value)
 
+port config dynf
+~~~~~~~~~~~~~~~~
+
+Set/clear dynamic flag per port.
+testpmd will register this flag in the mbuf (same registration
+for both Tx and Rx). Then set/clear this flag for each Tx
+packet sent from this port. The set bit only works for Tx packet::
+
+   testpmd> port config (port_id) dynf (name) (set|clear)
+
 port config mtu
 ~~~~~~~~~~~~~~~
 
@@ -3594,6 +3604,10 @@ following sections.
 
    flow isolate {port_id} {boolean}
 
+- Dump internal representation information of all flows in hardware::
+
+   flow dump {port_id} {output_file}
+
 Validating flow rules
 ~~~~~~~~~~~~~~~~~~~~~
 
@@ -3969,6 +3983,14 @@ This section lists supported pattern items and their attributes, if any.
 
   - ``proto_id {unsigned}``: PPP protocol identifier.
 
+- ``l2tpv3oip``: match L2TPv3 over IP header.
+
+  - ``session_id {unsigned}``: L2TPv3 over IP session identifier.
+
+- ``ah``: match AH header.
+
+  - ``spi {unsigned}``: security parameters index.
+
 Actions list
 ^^^^^^^^^^^^
 
@@ -4452,6 +4474,22 @@ Disabling isolated mode::
  Ingress traffic on port 0 is not restricted anymore to the defined flow rules
  testpmd>
 
+Dumping HW internal information
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+``flow dump`` dumps the hardware's internal representation information of
+all flows. It is bound to ``rte_flow_dev_dump()``::
+
+   flow dump {port_id} {output_file}
+
+If successful, it will show::
+
+   Flow dump finished
+
+Otherwise, it will complain error occurred::
+
+   Caught error type [...] ([...]): [...]
+
 Sample QinQ flow rules
 ~~~~~~~~~~~~~~~~~~~~~~
 
@@ -4774,6 +4812,34 @@ Decapsulating VxLAN::
  testpmd> flow create 0 ingress pattern eth / ipv4 / udp / vxlan / eth / ipv4 /
         end actions raw_decap / queue index 0 / end
 
+Sample ESP rules
+~~~~~~~~~~~~~~~~
+
+ESP rules can be created by the following commands::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / esp spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / esp spi is 1 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / esp spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / esp spi is 1 / end
+        actions queue index 3 / end
+
+Sample AH rules
+~~~~~~~~~~~~~~~~
+
+AH rules can be created by the following commands::
+
+ testpmd> flow create 0 ingress pattern eth / ipv4 / ah spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv4 / udp / ah spi is 1 / end
+        actions queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / ah spi is 1 / end actions
+        queue index 3 / end
+ testpmd> flow create 0 ingress pattern eth / ipv6 / udp / ah spi is 1 / end
+        actions queue index 3 / end
+
 BPF Functions
 --------------