net/mlx5: allow pattern start from IP

[dpdk.git] / drivers / net / mlx5 / mlx5_flow.c

diff --git a/drivers/net/mlx5/mlx5_flow.c b/drivers/net/mlx5/mlx5_flow.c
index 54f4cfe..e90301c 100644 (file)
--- a/drivers/net/mlx5/mlx5_flow.c
+++ b/drivers/net/mlx5/mlx5_flow.c
@@ -1276,11 +1276,17 @@ mlx5_flow_validate_item_eth(const struct rte_flow_item *item,
                return rte_flow_error_set(error, ENOTSUP,
                                          RTE_FLOW_ERROR_TYPE_ITEM, item,
                                          "multiple L2 layers not supported");
-       if (tunnel && (item_flags & MLX5_FLOW_LAYER_INNER_L3))
+       if ((!tunnel && (item_flags & MLX5_FLOW_LAYER_OUTER_L3)) ||
+           (tunnel && (item_flags & MLX5_FLOW_LAYER_INNER_L3)))
                return rte_flow_error_set(error, EINVAL,
                                          RTE_FLOW_ERROR_TYPE_ITEM, item,
-                                         "inner L2 layer should not "
-                                         "follow inner L3 layers");
+                                         "L2 layer should not follow "
+                                         "L3 layers");
+       if ((!tunnel && (item_flags & MLX5_FLOW_LAYER_OUTER_VLAN)) ||
+           (tunnel && (item_flags & MLX5_FLOW_LAYER_INNER_VLAN)))
+               return rte_flow_error_set(error, EINVAL,
+                                         RTE_FLOW_ERROR_TYPE_ITEM, item,
+                                         "L2 layer should not follow VLAN");
        if (!mask)
                mask = &rte_flow_item_eth_mask;
        ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
@@ -1327,8 +1333,6 @@ mlx5_flow_validate_item_vlan(const struct rte_flow_item *item,
        const uint64_t vlanm = tunnel ? MLX5_FLOW_LAYER_INNER_VLAN :
                                        MLX5_FLOW_LAYER_OUTER_VLAN;
 
-       const uint64_t l2m = tunnel ? MLX5_FLOW_LAYER_INNER_L2 :
-                                     MLX5_FLOW_LAYER_OUTER_L2;
        if (item_flags & vlanm)
                return rte_flow_error_set(error, EINVAL,
                                          RTE_FLOW_ERROR_TYPE_ITEM, item,
@@ -1336,11 +1340,7 @@ mlx5_flow_validate_item_vlan(const struct rte_flow_item *item,
        else if ((item_flags & l34m) != 0)
                return rte_flow_error_set(error, EINVAL,
                                          RTE_FLOW_ERROR_TYPE_ITEM, item,
-                                         "L2 layer cannot follow L3/L4 layer");
-       else if ((item_flags & l2m) == 0)
-               return rte_flow_error_set(error, EINVAL,
-                                         RTE_FLOW_ERROR_TYPE_ITEM, item,
-                                         "no L2 layer before VLAN");
+                                         "VLAN cannot follow L3/L4 layer");
        if (!mask)
                mask = &rte_flow_item_vlan_mask;
        ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
@@ -1464,10 +1464,6 @@ mlx5_flow_validate_item_ipv4(const struct rte_flow_item *item,
                return rte_flow_error_set(error, EINVAL,
                                          RTE_FLOW_ERROR_TYPE_ITEM, item,
                                          "L3 cannot follow an NVGRE layer.");
-       else if (!tunnel && !(item_flags & MLX5_FLOW_LAYER_OUTER_L2))
-               return rte_flow_error_set(error, EINVAL,
-                                         RTE_FLOW_ERROR_TYPE_ITEM, item,
-                                         "no L2 layer before IPV4");
        if (!mask)
                mask = &rte_flow_item_ipv4_mask;
        else if (mask->hdr.next_proto_id != 0 &&
@@ -1570,10 +1566,6 @@ mlx5_flow_validate_item_ipv6(const struct rte_flow_item *item,
                return rte_flow_error_set(error, EINVAL,
                                          RTE_FLOW_ERROR_TYPE_ITEM, item,
                                          "L3 cannot follow an NVGRE layer.");
-       else if (!tunnel && !(item_flags & MLX5_FLOW_LAYER_OUTER_L2))
-               return rte_flow_error_set(error, EINVAL,
-                                         RTE_FLOW_ERROR_TYPE_ITEM, item,
-                                         "no L2 layer before IPV6");
        if (!mask)
                mask = &rte_flow_item_ipv6_mask;
        ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,