+// SPDX-License-Identifier: GPL-2.0
/*******************************************************************************
Intel(R) Gigabit Ethernet Linux driver
- Copyright(c) 2007-2012 Intel Corporation.
-
- This program is free software; you can redistribute it and/or modify it
- under the terms and conditions of the GNU General Public License,
- version 2, as published by the Free Software Foundation.
-
- This program is distributed in the hope it will be useful, but WITHOUT
- ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
- more details.
-
- You should have received a copy of the GNU General Public License along with
- this program; if not, write to the Free Software Foundation, Inc.,
- 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
-
- The full GNU General Public License is included in this distribution in
- the file called "COPYING".
+ Copyright(c) 2007-2013 Intel Corporation.
Contact Information:
e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
static s32 e1000_validate_mdi_setting_generic(struct e1000_hw *hw);
static void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw);
static void e1000_config_collision_dist_generic(struct e1000_hw *hw);
+static void e1000_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index);
/**
* e1000_init_mac_ops_generic - Initialize MAC function pointers
mac->ops.setup_link = e1000_null_ops_generic;
mac->ops.get_link_up_info = e1000_null_link_info;
mac->ops.check_for_link = e1000_null_ops_generic;
- mac->ops.wait_autoneg = e1000_wait_autoneg_generic;
/* Management */
mac->ops.check_mng_mode = e1000_null_mng_mode;
- mac->ops.mng_host_if_write = e1000_mng_host_if_write_generic;
- mac->ops.mng_write_cmd_header = e1000_mng_write_cmd_header_generic;
- mac->ops.mng_enable_host_if = e1000_mng_enable_host_if_generic;
/* VLAN, MC, etc. */
mac->ops.update_mc_addr_list = e1000_null_update_mc;
mac->ops.clear_vfta = e1000_null_mac_generic;
* e1000_null_ops_generic - No-op function, returns 0
* @hw: pointer to the HW structure
**/
-s32 e1000_null_ops_generic(struct e1000_hw *hw)
+s32 e1000_null_ops_generic(struct e1000_hw E1000_UNUSEDARG *hw)
{
DEBUGFUNC("e1000_null_ops_generic");
return E1000_SUCCESS;
* e1000_null_mac_generic - No-op function, return void
* @hw: pointer to the HW structure
**/
-void e1000_null_mac_generic(struct e1000_hw *hw)
+void e1000_null_mac_generic(struct e1000_hw E1000_UNUSEDARG *hw)
{
DEBUGFUNC("e1000_null_mac_generic");
return;
* e1000_null_link_info - No-op function, return 0
* @hw: pointer to the HW structure
**/
-s32 e1000_null_link_info(struct e1000_hw *hw, u16 *s, u16 *d)
+s32 e1000_null_link_info(struct e1000_hw E1000_UNUSEDARG *hw,
+ u16 E1000_UNUSEDARG *s, u16 E1000_UNUSEDARG *d)
{
DEBUGFUNC("e1000_null_link_info");
return E1000_SUCCESS;
* e1000_null_mng_mode - No-op function, return false
* @hw: pointer to the HW structure
**/
-bool e1000_null_mng_mode(struct e1000_hw *hw)
+bool e1000_null_mng_mode(struct e1000_hw E1000_UNUSEDARG *hw)
{
DEBUGFUNC("e1000_null_mng_mode");
return false;
* e1000_null_update_mc - No-op function, return void
* @hw: pointer to the HW structure
**/
-void e1000_null_update_mc(struct e1000_hw *hw, u8 *h, u32 a)
+void e1000_null_update_mc(struct e1000_hw E1000_UNUSEDARG *hw,
+ u8 E1000_UNUSEDARG *h, u32 E1000_UNUSEDARG a)
{
DEBUGFUNC("e1000_null_update_mc");
return;
* e1000_null_write_vfta - No-op function, return void
* @hw: pointer to the HW structure
**/
-void e1000_null_write_vfta(struct e1000_hw *hw, u32 a, u32 b)
+void e1000_null_write_vfta(struct e1000_hw E1000_UNUSEDARG *hw,
+ u32 E1000_UNUSEDARG a, u32 E1000_UNUSEDARG b)
{
DEBUGFUNC("e1000_null_write_vfta");
return;
* e1000_null_rar_set - No-op function, return void
* @hw: pointer to the HW structure
**/
-void e1000_null_rar_set(struct e1000_hw *hw, u8 *h, u32 a)
+void e1000_null_rar_set(struct e1000_hw E1000_UNUSEDARG *hw,
+ u8 E1000_UNUSEDARG *h, u32 E1000_UNUSEDARG a)
{
DEBUGFUNC("e1000_null_rar_set");
return;
struct e1000_bus_info *bus = &hw->bus;
u32 reg;
- /*
- * The status register reports the correct function number
+ /* The status register reports the correct function number
* for the device regardless of function swap state.
*/
reg = E1000_READ_REG(hw, E1000_STATUS);
s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw)
{
u32 i;
- s32 ret_val = E1000_SUCCESS;
+ s32 ret_val;
u16 offset, nvm_alt_mac_addr_offset, nvm_data;
u8 alt_mac_addr[ETH_ADDR_LEN];
return ret_val;
- /*
- * Alternate MAC address is handled by the option ROM for 82580
+ /* Alternate MAC address is handled by the option ROM for 82580
* and newer. SW support not required.
*/
if (hw->mac.type >= e1000_82580)
return E1000_SUCCESS;
}
- /*
- * We have a valid alternate MAC address, and we want to treat it the
+ /* We have a valid alternate MAC address, and we want to treat it the
* same as the normal permanent MAC address stored by the HW into the
* RAR. Do this by mapping this address into RAR0.
*/
* Sets the receive address array register at index to the address passed
* in by addr.
**/
-void e1000_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index)
+static void e1000_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index)
{
u32 rar_low, rar_high;
DEBUGFUNC("e1000_rar_set_generic");
- /*
- * HW expects these in little endian so we reverse the byte order
+ /* HW expects these in little endian so we reverse the byte order
* from network order (big endian) to little endian
*/
rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) |
if (rar_low || rar_high)
rar_high |= E1000_RAH_AV;
- /*
- * Some bridges will combine consecutive 32-bit writes into
+ /* Some bridges will combine consecutive 32-bit writes into
* a single burst write, which will malfunction on some parts.
* The flushes avoid this.
*/
/* Register count multiplied by bits per register */
hash_mask = (hw->mac.mta_reg_count * 32) - 1;
- /*
- * For a mc_filter_type of 0, bit_shift is the number of left-shifts
+ /* For a mc_filter_type of 0, bit_shift is the number of left-shifts
* where 0xFF would still fall within the hash mask.
*/
while (hash_mask >> bit_shift != 0xFF)
bit_shift++;
- /*
- * The portion of the address that is used for the hash table
+ /* The portion of the address that is used for the hash table
* is determined by the mc_filter_type setting.
* The algorithm is such that there is a total of 8 bits of shifting.
* The bit_shift for a mc_filter_type of 0 represents the number of
DEBUGFUNC("e1000_check_for_copper_link");
- /*
- * We only want to go out to the PHY registers to see if Auto-Neg
+ /* We only want to go out to the PHY registers to see if Auto-Neg
* has completed and/or if our link status has changed. The
* get_link_status flag is set upon receiving a Link Status
* Change or Rx Sequence Error interrupt.
if (!mac->get_link_status)
return E1000_SUCCESS;
- /*
- * First we want to see if the MII Status Register reports
+ /* First we want to see if the MII Status Register reports
* link. If so, then we want to get the current speed/duplex
* of the PHY.
*/
mac->get_link_status = false;
- /*
- * Check if there was DownShift, must be checked
+ /* Check if there was DownShift, must be checked
* immediately after link-up
*/
e1000_check_downshift_generic(hw);
- /*
- * If we are forcing speed/duplex, then we simply return since
+ /* If we are forcing speed/duplex, then we simply return since
* we have already determined whether we have link or not.
*/
if (!mac->autoneg)
return -E1000_ERR_CONFIG;
- /*
- * Auto-Neg is enabled. Auto Speed Detection takes care
+ /* Auto-Neg is enabled. Auto Speed Detection takes care
* of MAC speed/duplex configuration. So we only need to
* configure Collision Distance in the MAC.
*/
mac->ops.config_collision_dist(hw);
- /*
- * Configure Flow Control now that Auto-Neg has completed.
+ /* Configure Flow Control now that Auto-Neg has completed.
* First, we need to restore the desired flow control
* settings because we may have had to re-autoneg with a
* different link partner.
status = E1000_READ_REG(hw, E1000_STATUS);
rxcw = E1000_READ_REG(hw, E1000_RXCW);
- /*
- * If we don't have link (auto-negotiation failed or link partner
+ /* If we don't have link (auto-negotiation failed or link partner
* cannot auto-negotiate), the cable is plugged in (we have signal),
* and our link partner is not trying to auto-negotiate with us (we
* are receiving idles or data), we need to force link up. We also
return ret_val;
}
} else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
- /*
- * If we are forcing link and we are receiving /C/ ordered
+ /* If we are forcing link and we are receiving /C/ ordered
* sets, re-enable auto-negotiation in the TXCW register
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
status = E1000_READ_REG(hw, E1000_STATUS);
rxcw = E1000_READ_REG(hw, E1000_RXCW);
- /*
- * If we don't have link (auto-negotiation failed or link partner
+ /* If we don't have link (auto-negotiation failed or link partner
* cannot auto-negotiate), and our link partner is not trying to
* auto-negotiate with us (we are receiving idles or data),
* we need to force link up. We also need to give auto-negotiation
return ret_val;
}
} else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
- /*
- * If we are forcing link and we are receiving /C/ ordered
+ /* If we are forcing link and we are receiving /C/ ordered
* sets, re-enable auto-negotiation in the TXCW register
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
mac->serdes_has_link = true;
} else if (!(E1000_TXCW_ANE & E1000_READ_REG(hw, E1000_TXCW))) {
- /*
- * If we force link for non-auto-negotiation switch, check
+ /* If we force link for non-auto-negotiation switch, check
* link status based on MAC synchronization for internal
* serdes media type.
*/
DEBUGFUNC("e1000_set_default_fc_generic");
- /*
- * Read and store word 0x0F of the EEPROM. This word contains bits
+ /* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
* a bit that determines whether the HW defaults to enabling or
* disabling auto-negotiation, and the direction of the
return ret_val;
}
- if ((nvm_data & NVM_WORD0F_PAUSE_MASK) == 0)
+ if (!(nvm_data & NVM_WORD0F_PAUSE_MASK))
hw->fc.requested_mode = e1000_fc_none;
else if ((nvm_data & NVM_WORD0F_PAUSE_MASK) ==
NVM_WORD0F_ASM_DIR)
DEBUGFUNC("e1000_setup_link_generic");
- /*
- * In the case of the phy reset being blocked, we already have a link.
+ /* In the case of the phy reset being blocked, we already have a link.
* We do not need to set it up again.
*/
- if (hw->phy.ops.check_reset_block(hw))
+ if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw))
return E1000_SUCCESS;
- /*
- * If requested flow control is set to default, set flow control
+ /* If requested flow control is set to default, set flow control
* based on the EEPROM flow control settings.
*/
if (hw->fc.requested_mode == e1000_fc_default) {
return ret_val;
}
- /*
- * Save off the requested flow control mode for use later. Depending
+ /* Save off the requested flow control mode for use later. Depending
* on the link partner's capabilities, we may or may not use this mode.
*/
hw->fc.current_mode = hw->fc.requested_mode;
if (ret_val)
return ret_val;
- /*
- * Initialize the flow control address, type, and PAUSE timer
+ /* Initialize the flow control address, type, and PAUSE timer
* registers to their default values. This is done even if flow
* control is disabled, because it does not hurt anything to
* initialize these registers.
DEBUGFUNC("e1000_commit_fc_settings_generic");
- /*
- * Check for a software override of the flow control settings, and
+ /* Check for a software override of the flow control settings, and
* setup the device accordingly. If auto-negotiation is enabled, then
* software will have to set the "PAUSE" bits to the correct value in
* the Transmit Config Word Register (TXCW) and re-start auto-
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
break;
case e1000_fc_rx_pause:
- /*
- * Rx Flow control is enabled and Tx Flow control is disabled
+ /* Rx Flow control is enabled and Tx Flow control is disabled
* by a software over-ride. Since there really isn't a way to
* advertise that we are capable of Rx Pause ONLY, we will
* advertise that we support both symmetric and asymmetric Rx
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
break;
case e1000_fc_tx_pause:
- /*
- * Tx Flow control is enabled, and Rx Flow control is disabled,
+ /* Tx Flow control is enabled, and Rx Flow control is disabled,
* by a software over-ride.
*/
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
break;
case e1000_fc_full:
- /*
- * Flow control (both Rx and Tx) is enabled by a software
+ /* Flow control (both Rx and Tx) is enabled by a software
* over-ride.
*/
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
DEBUGFUNC("e1000_poll_fiber_serdes_link_generic");
- /*
- * If we have a signal (the cable is plugged in, or assumed true for
+ /* If we have a signal (the cable is plugged in, or assumed true for
* serdes media) then poll for a "Link-Up" indication in the Device
* Status Register. Time-out if a link isn't seen in 500 milliseconds
* seconds (Auto-negotiation should complete in less than 500
if (i == FIBER_LINK_UP_LIMIT) {
DEBUGOUT("Never got a valid link from auto-neg!!!\n");
mac->autoneg_failed = true;
- /*
- * AutoNeg failed to achieve a link, so we'll call
+ /* AutoNeg failed to achieve a link, so we'll call
* mac->check_for_link. This routine will force the
* link up if we detect a signal. This will allow us to
* communicate with non-autonegotiating link partners.
if (ret_val)
return ret_val;
- /*
- * Since auto-negotiation is enabled, take the link out of reset (the
+ /* Since auto-negotiation is enabled, take the link out of reset (the
* link will be in reset, because we previously reset the chip). This
* will restart auto-negotiation. If auto-negotiation is successful
* then the link-up status bit will be set and the flow control enable
E1000_WRITE_FLUSH(hw);
msec_delay(1);
- /*
- * For these adapters, the SW definable pin 1 is set when the optics
+ /* For these adapters, the SW definable pin 1 is set when the optics
* detect a signal. If we have a signal, then poll for a "Link-Up"
* indication.
*/
DEBUGFUNC("e1000_set_fc_watermarks_generic");
- /*
- * Set the flow control receive threshold registers. Normally,
+ /* Set the flow control receive threshold registers. Normally,
* these registers will be set to a default threshold that may be
* adjusted later by the driver's runtime code. However, if the
* ability to transmit pause frames is not enabled, then these
* registers will be set to 0.
*/
if (hw->fc.current_mode & e1000_fc_tx_pause) {
- /*
- * We need to set up the Receive Threshold high and low water
+ /* We need to set up the Receive Threshold high and low water
* marks as well as (optionally) enabling the transmission of
* XON frames.
*/
ctrl = E1000_READ_REG(hw, E1000_CTRL);
- /*
- * Because we didn't get link via the internal auto-negotiation
+ /* Because we didn't get link via the internal auto-negotiation
* mechanism (we either forced link or we got link via PHY
* auto-neg), we have to manually enable/disable transmit an
* receive flow control.
{
struct e1000_mac_info *mac = &hw->mac;
s32 ret_val = E1000_SUCCESS;
+ u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg;
u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg;
u16 speed, duplex;
DEBUGFUNC("e1000_config_fc_after_link_up_generic");
- /*
- * Check for the case where we have fiber media and auto-neg failed
+ /* Check for the case where we have fiber media and auto-neg failed
* so we had to force link. In this case, we need to force the
* configuration of the MAC to match the "fc" parameter.
*/
return ret_val;
}
- /*
- * Check for the case where we have copper media and auto-neg is
+ /* Check for the case where we have copper media and auto-neg is
* enabled. In this case, we need to check and see if Auto-Neg
* has completed, and if so, how the PHY and link partner has
* flow control configured.
*/
if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) {
- /*
- * Read the MII Status Register and check to see if AutoNeg
+ /* Read the MII Status Register and check to see if AutoNeg
* has completed. We read this twice because this reg has
* some "sticky" (latched) bits.
*/
return ret_val;
}
- /*
- * The AutoNeg process has completed, so we now need to
+ /* The AutoNeg process has completed, so we now need to
* read both the Auto Negotiation Advertisement
* Register (Address 4) and the Auto_Negotiation Base
* Page Ability Register (Address 5) to determine how
if (ret_val)
return ret_val;
- /*
- * Two bits in the Auto Negotiation Advertisement Register
+ /* Two bits in the Auto Negotiation Advertisement Register
* (Address 4) and two bits in the Auto Negotiation Base
* Page Ability Register (Address 5) determine flow control
* for both the PHY and the link partner. The following
*/
if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
- /*
- * Now we need to check if the user selected Rx ONLY
+ /* Now we need to check if the user selected Rx ONLY
* of pause frames. In this case, we had to advertise
* FULL flow control because we could not advertise Rx
* ONLY. Hence, we must now check to see if we need to
DEBUGOUT("Flow Control = Rx PAUSE frames only.\n");
}
}
- /*
- * For receiving PAUSE frames ONLY.
+ /* For receiving PAUSE frames ONLY.
*
* LOCAL DEVICE | LINK PARTNER
* PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
hw->fc.current_mode = e1000_fc_tx_pause;
DEBUGOUT("Flow Control = Tx PAUSE frames only.\n");
}
- /*
- * For transmitting PAUSE frames ONLY.
+ /* For transmitting PAUSE frames ONLY.
*
* LOCAL DEVICE | LINK PARTNER
* PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
hw->fc.current_mode = e1000_fc_rx_pause;
DEBUGOUT("Flow Control = Rx PAUSE frames only.\n");
} else {
- /*
- * Per the IEEE spec, at this point flow control
+ /* Per the IEEE spec, at this point flow control
* should be disabled.
*/
hw->fc.current_mode = e1000_fc_none;
DEBUGOUT("Flow Control = NONE.\n");
}
- /*
- * Now we need to do one last check... If we auto-
+ /* Now we need to do one last check... If we auto-
* negotiated to HALF DUPLEX, flow control should not be
* enabled per IEEE 802.3 spec.
*/
if (duplex == HALF_DUPLEX)
hw->fc.current_mode = e1000_fc_none;
- /*
- * Now we call a subroutine to actually force the MAC
+ /* Now we call a subroutine to actually force the MAC
* controller to use the correct flow control settings.
*/
ret_val = e1000_force_mac_fc_generic(hw);
}
}
+ /* Check for the case where we have SerDes media and auto-neg is
+ * enabled. In this case, we need to check and see if Auto-Neg
+ * has completed, and if so, how the PHY and link partner has
+ * flow control configured.
+ */
+ if ((hw->phy.media_type == e1000_media_type_internal_serdes) &&
+ mac->autoneg) {
+ /* Read the PCS_LSTS and check to see if AutoNeg
+ * has completed.
+ */
+ pcs_status_reg = E1000_READ_REG(hw, E1000_PCS_LSTAT);
+
+ if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) {
+ DEBUGOUT("PCS Auto Neg has not completed.\n");
+ return ret_val;
+ }
+
+ /* The AutoNeg process has completed, so we now need to
+ * read both the Auto Negotiation Advertisement
+ * Register (PCS_ANADV) and the Auto_Negotiation Base
+ * Page Ability Register (PCS_LPAB) to determine how
+ * flow control was negotiated.
+ */
+ pcs_adv_reg = E1000_READ_REG(hw, E1000_PCS_ANADV);
+ pcs_lp_ability_reg = E1000_READ_REG(hw, E1000_PCS_LPAB);
+
+ /* Two bits in the Auto Negotiation Advertisement Register
+ * (PCS_ANADV) and two bits in the Auto Negotiation Base
+ * Page Ability Register (PCS_LPAB) determine flow control
+ * for both the PHY and the link partner. The following
+ * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
+ * 1999, describes these PAUSE resolution bits and how flow
+ * control is determined based upon these settings.
+ * NOTE: DC = Don't Care
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
+ *-------|---------|-------|---------|--------------------
+ * 0 | 0 | DC | DC | e1000_fc_none
+ * 0 | 1 | 0 | DC | e1000_fc_none
+ * 0 | 1 | 1 | 0 | e1000_fc_none
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ * 1 | 0 | 0 | DC | e1000_fc_none
+ * 1 | DC | 1 | DC | e1000_fc_full
+ * 1 | 1 | 0 | 0 | e1000_fc_none
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ *
+ * Are both PAUSE bits set to 1? If so, this implies
+ * Symmetric Flow Control is enabled at both ends. The
+ * ASM_DIR bits are irrelevant per the spec.
+ *
+ * For Symmetric Flow Control:
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | DC | 1 | DC | e1000_fc_full
+ *
+ */
+ if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) {
+ /* Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise Rx
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == e1000_fc_full) {
+ hw->fc.current_mode = e1000_fc_full;
+ DEBUGOUT("Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ DEBUGOUT("Flow Control = Rx PAUSE frames only.\n");
+ }
+ }
+ /* For receiving PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 0 | 1 | 1 | 1 | e1000_fc_tx_pause
+ */
+ else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+ (pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_tx_pause;
+ DEBUGOUT("Flow Control = Tx PAUSE frames only.\n");
+ }
+ /* For transmitting PAUSE frames ONLY.
+ *
+ * LOCAL DEVICE | LINK PARTNER
+ * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
+ *-------|---------|-------|---------|--------------------
+ * 1 | 1 | 0 | 1 | e1000_fc_rx_pause
+ */
+ else if ((pcs_adv_reg & E1000_TXCW_PAUSE) &&
+ (pcs_adv_reg & E1000_TXCW_ASM_DIR) &&
+ !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) &&
+ (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) {
+ hw->fc.current_mode = e1000_fc_rx_pause;
+ DEBUGOUT("Flow Control = Rx PAUSE frames only.\n");
+ } else {
+ /* Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
+ hw->fc.current_mode = e1000_fc_none;
+ DEBUGOUT("Flow Control = NONE.\n");
+ }
+
+ /* Now we call a subroutine to actually force the MAC
+ * controller to use the correct flow control settings.
+ */
+ pcs_ctrl_reg = E1000_READ_REG(hw, E1000_PCS_LCTL);
+ pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL;
+ E1000_WRITE_REG(hw, E1000_PCS_LCTL, pcs_ctrl_reg);
+
+ ret_val = e1000_force_mac_fc_generic(hw);
+ if (ret_val) {
+ DEBUGOUT("Error forcing flow control settings\n");
+ return ret_val;
+ }
+ }
+
return E1000_SUCCESS;
}
* Sets the speed and duplex to gigabit full duplex (the only possible option)
* for fiber/serdes links.
**/
-s32 e1000_get_speed_and_duplex_fiber_serdes_generic(struct e1000_hw *hw,
+s32 e1000_get_speed_and_duplex_fiber_serdes_generic(struct e1000_hw E1000_UNUSEDARG *hw,
u16 *speed, u16 *duplex)
{
DEBUGFUNC("e1000_get_speed_and_duplex_fiber_serdes_generic");
ledctl_blink = E1000_LEDCTL_LED0_BLINK |
(E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
} else {
- /*
- * set the blink bit for each LED that's "on" (0x0E)
- * in ledctl_mode2
+ /* Set the blink bit for each LED that's "on" (0x0E)
+ * (or "off" if inverted) in ledctl_mode2. The blink
+ * logic in hardware only works when mode is set to "on"
+ * so it must be changed accordingly when the mode is
+ * "off" and inverted.
*/
ledctl_blink = hw->mac.ledctl_mode2;
- for (i = 0; i < 4; i++)
- if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
- E1000_LEDCTL_MODE_LED_ON)
- ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
- (i * 8));
+ for (i = 0; i < 32; i += 8) {
+ u32 mode = (hw->mac.ledctl_mode2 >> i) &
+ E1000_LEDCTL_LED0_MODE_MASK;
+ u32 led_default = hw->mac.ledctl_default >> i;
+
+ if ((!(led_default & E1000_LEDCTL_LED0_IVRT) &&
+ (mode == E1000_LEDCTL_MODE_LED_ON)) ||
+ ((led_default & E1000_LEDCTL_LED0_IVRT) &&
+ (mode == E1000_LEDCTL_MODE_LED_OFF))) {
+ ledctl_blink &=
+ ~(E1000_LEDCTL_LED0_MODE_MASK << i);
+ ledctl_blink |= (E1000_LEDCTL_LED0_BLINK |
+ E1000_LEDCTL_MODE_LED_ON) << i;
+ }
+ }
}
E1000_WRITE_REG(hw, E1000_LEDCTL, ledctl_blink);
return E1000_SUCCESS;
}
+/**
+ * e1000_validate_mdi_setting_crossover_generic - Verify MDI/MDIx settings
+ * @hw: pointer to the HW structure
+ *
+ * Validate the MDI/MDIx setting, allowing for auto-crossover during forced
+ * operation.
+ **/
+s32 e1000_validate_mdi_setting_crossover_generic(struct e1000_hw E1000_UNUSEDARG *hw)
+{
+ DEBUGFUNC("e1000_validate_mdi_setting_crossover_generic");
+
+ return E1000_SUCCESS;
+}
+
/**
* e1000_write_8bit_ctrl_reg_generic - Write a 8bit CTRL register
* @hw: pointer to the HW structure
git.droids-corp.org / dpdk.git / blobdiff