* - The driver-oriented Ethernet API that exports functions allowing
* an Ethernet Poll Mode Driver (PMD) to allocate an Ethernet device instance,
* create memzone for HW rings and process registered callbacks, and so on.
- * PMDs should include rte_ethdev_driver.h instead of this header.
+ * PMDs should include ethdev_driver.h instead of this header.
*
* By default, all the functions of the Ethernet Device API exported by a PMD
* are lock-free functions which assume to not be invoked in parallel on
/* Use this macro to check if LRO API is supported */
#define RTE_ETHDEV_HAS_LRO_SUPPORT
+/* Alias RTE_LIBRTE_ETHDEV_DEBUG for backward compatibility. */
+#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#define RTE_ETHDEV_DEBUG_RX
+#define RTE_ETHDEV_DEBUG_TX
+#endif
+
#include <rte_compat.h>
#include <rte_log.h>
#include <rte_interrupts.h>
#include <rte_errno.h>
#include <rte_common.h>
#include <rte_config.h>
+#include <rte_ether.h>
+#include <rte_power_intrinsics.h>
-#include "rte_ether.h"
-#include "rte_eth_ctrl.h"
+#include "rte_ethdev_trace_fp.h"
#include "rte_dev_info.h"
extern int rte_eth_dev_logtype;
* Not all statistics fields in struct rte_eth_stats are supported
* by any type of network interface card (NIC). If any statistics
* field is not supported, its value is 0.
+ * All byte-related statistics do not include Ethernet FCS regardless
+ * of whether these bytes have been delivered to the application
+ * (see DEV_RX_OFFLOAD_KEEP_CRC).
*/
struct rte_eth_stats {
uint64_t ipackets; /**< Total number of successfully received packets. */
uint64_t ierrors; /**< Total number of erroneous received packets. */
uint64_t oerrors; /**< Total number of failed transmitted packets. */
uint64_t rx_nombuf; /**< Total number of RX mbuf allocation failures. */
+ /* Queue stats are limited to max 256 queues */
uint64_t q_ipackets[RTE_ETHDEV_QUEUE_STAT_CNTRS];
/**< Total number of queue RX packets. */
uint64_t q_opackets[RTE_ETHDEV_QUEUE_STAT_CNTRS];
#define ETH_LINK_SPEED_50G (1 << 12) /**< 50 Gbps */
#define ETH_LINK_SPEED_56G (1 << 13) /**< 56 Gbps */
#define ETH_LINK_SPEED_100G (1 << 14) /**< 100 Gbps */
+#define ETH_LINK_SPEED_200G (1 << 15) /**< 200 Gbps */
/**
* Ethernet numeric link speeds in Mbps
#define ETH_SPEED_NUM_50G 50000 /**< 50 Gbps */
#define ETH_SPEED_NUM_56G 56000 /**< 56 Gbps */
#define ETH_SPEED_NUM_100G 100000 /**< 100 Gbps */
+#define ETH_SPEED_NUM_200G 200000 /**< 200 Gbps */
+#define ETH_SPEED_NUM_UNKNOWN UINT32_MAX /**< Unknown */
/**
* A structure used to retrieve link-level information of an Ethernet port.
uint16_t link_duplex : 1; /**< ETH_LINK_[HALF/FULL]_DUPLEX */
uint16_t link_autoneg : 1; /**< ETH_LINK_[AUTONEG/FIXED] */
uint16_t link_status : 1; /**< ETH_LINK_[DOWN/UP] */
-} __attribute__((aligned(8))); /**< aligned for atomic64 read/write */
+} __rte_aligned(8); /**< aligned for atomic64 read/write */
/* Utility constants */
#define ETH_LINK_HALF_DUPLEX 0 /**< Half-duplex connection (see link_duplex). */
#define ETH_LINK_UP 1 /**< Link is up (see link_status). */
#define ETH_LINK_FIXED 0 /**< No autonegotiation (see link_autoneg). */
#define ETH_LINK_AUTONEG 1 /**< Autonegotiated (see link_autoneg). */
+#define RTE_ETH_LINK_MAX_STR_LEN 40 /**< Max length of default link string. */
/**
* A structure used to configure the ring threshold registers of an RX/TX
/** The multi-queue packet distribution mode to be used, e.g. RSS. */
enum rte_eth_rx_mq_mode mq_mode;
uint32_t max_rx_pkt_len; /**< Only used if JUMBO_FRAME enabled. */
+ /** Maximum allowed size of LRO aggregated packet. */
+ uint32_t max_lro_pkt_size;
uint16_t split_hdr_size; /**< hdr buf size (header_split enabled).*/
/**
* Per-port Rx offloads to be set using DEV_RX_OFFLOAD_* flags.
* structure are allowed to be set.
*/
uint64_t offloads;
+
+ uint64_t reserved_64s[2]; /**< Reserved for future fields */
+ void *reserved_ptrs[2]; /**< Reserved for future fields */
};
/**
};
/*
- * The RSS offload types are defined based on flow types which are defined
- * in rte_eth_ctrl.h. Different NIC hardwares may support different RSS offload
- * types. The supported flow types or RSS offload types can be queried by
- * rte_eth_dev_info_get().
- */
-#define ETH_RSS_IPV4 (1ULL << RTE_ETH_FLOW_IPV4)
-#define ETH_RSS_FRAG_IPV4 (1ULL << RTE_ETH_FLOW_FRAG_IPV4)
-#define ETH_RSS_NONFRAG_IPV4_TCP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_TCP)
-#define ETH_RSS_NONFRAG_IPV4_UDP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_UDP)
-#define ETH_RSS_NONFRAG_IPV4_SCTP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_SCTP)
-#define ETH_RSS_NONFRAG_IPV4_OTHER (1ULL << RTE_ETH_FLOW_NONFRAG_IPV4_OTHER)
-#define ETH_RSS_IPV6 (1ULL << RTE_ETH_FLOW_IPV6)
-#define ETH_RSS_FRAG_IPV6 (1ULL << RTE_ETH_FLOW_FRAG_IPV6)
-#define ETH_RSS_NONFRAG_IPV6_TCP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_TCP)
-#define ETH_RSS_NONFRAG_IPV6_UDP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_UDP)
-#define ETH_RSS_NONFRAG_IPV6_SCTP (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_SCTP)
-#define ETH_RSS_NONFRAG_IPV6_OTHER (1ULL << RTE_ETH_FLOW_NONFRAG_IPV6_OTHER)
-#define ETH_RSS_L2_PAYLOAD (1ULL << RTE_ETH_FLOW_L2_PAYLOAD)
-#define ETH_RSS_IPV6_EX (1ULL << RTE_ETH_FLOW_IPV6_EX)
-#define ETH_RSS_IPV6_TCP_EX (1ULL << RTE_ETH_FLOW_IPV6_TCP_EX)
-#define ETH_RSS_IPV6_UDP_EX (1ULL << RTE_ETH_FLOW_IPV6_UDP_EX)
-#define ETH_RSS_PORT (1ULL << RTE_ETH_FLOW_PORT)
-#define ETH_RSS_VXLAN (1ULL << RTE_ETH_FLOW_VXLAN)
-#define ETH_RSS_GENEVE (1ULL << RTE_ETH_FLOW_GENEVE)
-#define ETH_RSS_NVGRE (1ULL << RTE_ETH_FLOW_NVGRE)
+ * A packet can be identified by hardware as different flow types. Different
+ * NIC hardware may support different flow types.
+ * Basically, the NIC hardware identifies the flow type as deep protocol as
+ * possible, and exclusively. For example, if a packet is identified as
+ * 'RTE_ETH_FLOW_NONFRAG_IPV4_TCP', it will not be any of other flow types,
+ * though it is an actual IPV4 packet.
+ */
+#define RTE_ETH_FLOW_UNKNOWN 0
+#define RTE_ETH_FLOW_RAW 1
+#define RTE_ETH_FLOW_IPV4 2
+#define RTE_ETH_FLOW_FRAG_IPV4 3
+#define RTE_ETH_FLOW_NONFRAG_IPV4_TCP 4
+#define RTE_ETH_FLOW_NONFRAG_IPV4_UDP 5
+#define RTE_ETH_FLOW_NONFRAG_IPV4_SCTP 6
+#define RTE_ETH_FLOW_NONFRAG_IPV4_OTHER 7
+#define RTE_ETH_FLOW_IPV6 8
+#define RTE_ETH_FLOW_FRAG_IPV6 9
+#define RTE_ETH_FLOW_NONFRAG_IPV6_TCP 10
+#define RTE_ETH_FLOW_NONFRAG_IPV6_UDP 11
+#define RTE_ETH_FLOW_NONFRAG_IPV6_SCTP 12
+#define RTE_ETH_FLOW_NONFRAG_IPV6_OTHER 13
+#define RTE_ETH_FLOW_L2_PAYLOAD 14
+#define RTE_ETH_FLOW_IPV6_EX 15
+#define RTE_ETH_FLOW_IPV6_TCP_EX 16
+#define RTE_ETH_FLOW_IPV6_UDP_EX 17
+#define RTE_ETH_FLOW_PORT 18
+ /**< Consider device port number as a flow differentiator */
+#define RTE_ETH_FLOW_VXLAN 19 /**< VXLAN protocol based flow */
+#define RTE_ETH_FLOW_GENEVE 20 /**< GENEVE protocol based flow */
+#define RTE_ETH_FLOW_NVGRE 21 /**< NVGRE protocol based flow */
+#define RTE_ETH_FLOW_VXLAN_GPE 22 /**< VXLAN-GPE protocol based flow */
+#define RTE_ETH_FLOW_GTPU 23 /**< GTPU protocol based flow */
+#define RTE_ETH_FLOW_MAX 24
+
+/*
+ * Below macros are defined for RSS offload types, they can be used to
+ * fill rte_eth_rss_conf.rss_hf or rte_flow_action_rss.types.
+ */
+#define ETH_RSS_IPV4 (1ULL << 2)
+#define ETH_RSS_FRAG_IPV4 (1ULL << 3)
+#define ETH_RSS_NONFRAG_IPV4_TCP (1ULL << 4)
+#define ETH_RSS_NONFRAG_IPV4_UDP (1ULL << 5)
+#define ETH_RSS_NONFRAG_IPV4_SCTP (1ULL << 6)
+#define ETH_RSS_NONFRAG_IPV4_OTHER (1ULL << 7)
+#define ETH_RSS_IPV6 (1ULL << 8)
+#define ETH_RSS_FRAG_IPV6 (1ULL << 9)
+#define ETH_RSS_NONFRAG_IPV6_TCP (1ULL << 10)
+#define ETH_RSS_NONFRAG_IPV6_UDP (1ULL << 11)
+#define ETH_RSS_NONFRAG_IPV6_SCTP (1ULL << 12)
+#define ETH_RSS_NONFRAG_IPV6_OTHER (1ULL << 13)
+#define ETH_RSS_L2_PAYLOAD (1ULL << 14)
+#define ETH_RSS_IPV6_EX (1ULL << 15)
+#define ETH_RSS_IPV6_TCP_EX (1ULL << 16)
+#define ETH_RSS_IPV6_UDP_EX (1ULL << 17)
+#define ETH_RSS_PORT (1ULL << 18)
+#define ETH_RSS_VXLAN (1ULL << 19)
+#define ETH_RSS_GENEVE (1ULL << 20)
+#define ETH_RSS_NVGRE (1ULL << 21)
+#define ETH_RSS_GTPU (1ULL << 23)
+#define ETH_RSS_ETH (1ULL << 24)
+#define ETH_RSS_S_VLAN (1ULL << 25)
+#define ETH_RSS_C_VLAN (1ULL << 26)
+#define ETH_RSS_ESP (1ULL << 27)
+#define ETH_RSS_AH (1ULL << 28)
+#define ETH_RSS_L2TPV3 (1ULL << 29)
+#define ETH_RSS_PFCP (1ULL << 30)
+#define ETH_RSS_PPPOE (1ULL << 31)
+#define ETH_RSS_ECPRI (1ULL << 32)
+#define ETH_RSS_MPLS (1ULL << 33)
+
+/*
+ * We use the following macros to combine with above ETH_RSS_* for
+ * more specific input set selection. These bits are defined starting
+ * from the high end of the 64 bits.
+ * Note: If we use above ETH_RSS_* without SRC/DST_ONLY, it represents
+ * both SRC and DST are taken into account. If SRC_ONLY and DST_ONLY of
+ * the same level are used simultaneously, it is the same case as none of
+ * them are added.
+ */
+#define ETH_RSS_L3_SRC_ONLY (1ULL << 63)
+#define ETH_RSS_L3_DST_ONLY (1ULL << 62)
+#define ETH_RSS_L4_SRC_ONLY (1ULL << 61)
+#define ETH_RSS_L4_DST_ONLY (1ULL << 60)
+#define ETH_RSS_L2_SRC_ONLY (1ULL << 59)
+#define ETH_RSS_L2_DST_ONLY (1ULL << 58)
+
+/*
+ * Only select IPV6 address prefix as RSS input set according to
+ * https://tools.ietf.org/html/rfc6052
+ * Must be combined with ETH_RSS_IPV6, ETH_RSS_NONFRAG_IPV6_UDP,
+ * ETH_RSS_NONFRAG_IPV6_TCP, ETH_RSS_NONFRAG_IPV6_SCTP.
+ */
+#define RTE_ETH_RSS_L3_PRE32 (1ULL << 57)
+#define RTE_ETH_RSS_L3_PRE40 (1ULL << 56)
+#define RTE_ETH_RSS_L3_PRE48 (1ULL << 55)
+#define RTE_ETH_RSS_L3_PRE56 (1ULL << 54)
+#define RTE_ETH_RSS_L3_PRE64 (1ULL << 53)
+#define RTE_ETH_RSS_L3_PRE96 (1ULL << 52)
+
+/*
+ * Use the following macros to combine with the above layers
+ * to choose inner and outer layers or both for RSS computation.
+ * Bits 50 and 51 are reserved for this.
+ */
+
+/**
+ * level 0, requests the default behavior.
+ * Depending on the packet type, it can mean outermost, innermost,
+ * anything in between or even no RSS.
+ * It basically stands for the innermost encapsulation level RSS
+ * can be performed on according to PMD and device capabilities.
+ */
+#define ETH_RSS_LEVEL_PMD_DEFAULT (0ULL << 50)
+
+/**
+ * level 1, requests RSS to be performed on the outermost packet
+ * encapsulation level.
+ */
+#define ETH_RSS_LEVEL_OUTERMOST (1ULL << 50)
+
+/**
+ * level 2, requests RSS to be performed on the specified inner packet
+ * encapsulation level, from outermost to innermost (lower to higher values).
+ */
+#define ETH_RSS_LEVEL_INNERMOST (2ULL << 50)
+#define ETH_RSS_LEVEL_MASK (3ULL << 50)
+
+#define ETH_RSS_LEVEL(rss_hf) ((rss_hf & ETH_RSS_LEVEL_MASK) >> 50)
+
+/**
+ * For input set change of hash filter, if SRC_ONLY and DST_ONLY of
+ * the same level are used simultaneously, it is the same case as
+ * none of them are added.
+ *
+ * @param rss_hf
+ * RSS types with SRC/DST_ONLY.
+ * @return
+ * RSS types.
+ */
+static inline uint64_t
+rte_eth_rss_hf_refine(uint64_t rss_hf)
+{
+ if ((rss_hf & ETH_RSS_L3_SRC_ONLY) && (rss_hf & ETH_RSS_L3_DST_ONLY))
+ rss_hf &= ~(ETH_RSS_L3_SRC_ONLY | ETH_RSS_L3_DST_ONLY);
+
+ if ((rss_hf & ETH_RSS_L4_SRC_ONLY) && (rss_hf & ETH_RSS_L4_DST_ONLY))
+ rss_hf &= ~(ETH_RSS_L4_SRC_ONLY | ETH_RSS_L4_DST_ONLY);
+
+ return rss_hf;
+}
+
+#define ETH_RSS_IPV6_PRE32 ( \
+ ETH_RSS_IPV6 | \
+ RTE_ETH_RSS_L3_PRE32)
+
+#define ETH_RSS_IPV6_PRE40 ( \
+ ETH_RSS_IPV6 | \
+ RTE_ETH_RSS_L3_PRE40)
+
+#define ETH_RSS_IPV6_PRE48 ( \
+ ETH_RSS_IPV6 | \
+ RTE_ETH_RSS_L3_PRE48)
+
+#define ETH_RSS_IPV6_PRE56 ( \
+ ETH_RSS_IPV6 | \
+ RTE_ETH_RSS_L3_PRE56)
+
+#define ETH_RSS_IPV6_PRE64 ( \
+ ETH_RSS_IPV6 | \
+ RTE_ETH_RSS_L3_PRE64)
+
+#define ETH_RSS_IPV6_PRE96 ( \
+ ETH_RSS_IPV6 | \
+ RTE_ETH_RSS_L3_PRE96)
+
+#define ETH_RSS_IPV6_PRE32_UDP ( \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ RTE_ETH_RSS_L3_PRE32)
+
+#define ETH_RSS_IPV6_PRE40_UDP ( \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ RTE_ETH_RSS_L3_PRE40)
+
+#define ETH_RSS_IPV6_PRE48_UDP ( \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ RTE_ETH_RSS_L3_PRE48)
+
+#define ETH_RSS_IPV6_PRE56_UDP ( \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ RTE_ETH_RSS_L3_PRE56)
+
+#define ETH_RSS_IPV6_PRE64_UDP ( \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ RTE_ETH_RSS_L3_PRE64)
+
+#define ETH_RSS_IPV6_PRE96_UDP ( \
+ ETH_RSS_NONFRAG_IPV6_UDP | \
+ RTE_ETH_RSS_L3_PRE96)
+
+#define ETH_RSS_IPV6_PRE32_TCP ( \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ RTE_ETH_RSS_L3_PRE32)
+
+#define ETH_RSS_IPV6_PRE40_TCP ( \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ RTE_ETH_RSS_L3_PRE40)
+
+#define ETH_RSS_IPV6_PRE48_TCP ( \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ RTE_ETH_RSS_L3_PRE48)
+
+#define ETH_RSS_IPV6_PRE56_TCP ( \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ RTE_ETH_RSS_L3_PRE56)
+
+#define ETH_RSS_IPV6_PRE64_TCP ( \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ RTE_ETH_RSS_L3_PRE64)
+
+#define ETH_RSS_IPV6_PRE96_TCP ( \
+ ETH_RSS_NONFRAG_IPV6_TCP | \
+ RTE_ETH_RSS_L3_PRE96)
+
+#define ETH_RSS_IPV6_PRE32_SCTP ( \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ RTE_ETH_RSS_L3_PRE32)
+
+#define ETH_RSS_IPV6_PRE40_SCTP ( \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ RTE_ETH_RSS_L3_PRE40)
+
+#define ETH_RSS_IPV6_PRE48_SCTP ( \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ RTE_ETH_RSS_L3_PRE48)
+
+#define ETH_RSS_IPV6_PRE56_SCTP ( \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ RTE_ETH_RSS_L3_PRE56)
+
+#define ETH_RSS_IPV6_PRE64_SCTP ( \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ RTE_ETH_RSS_L3_PRE64)
+
+#define ETH_RSS_IPV6_PRE96_SCTP ( \
+ ETH_RSS_NONFRAG_IPV6_SCTP | \
+ RTE_ETH_RSS_L3_PRE96)
#define ETH_RSS_IP ( \
ETH_RSS_IPV4 | \
ETH_RSS_GENEVE | \
ETH_RSS_NVGRE)
+#define ETH_RSS_VLAN ( \
+ ETH_RSS_S_VLAN | \
+ ETH_RSS_C_VLAN)
+
/**< Mask of valid RSS hash protocols */
#define ETH_RSS_PROTO_MASK ( \
ETH_RSS_IPV4 | \
ETH_RSS_PORT | \
ETH_RSS_VXLAN | \
ETH_RSS_GENEVE | \
- ETH_RSS_NVGRE)
+ ETH_RSS_NVGRE | \
+ ETH_RSS_MPLS)
/*
* Definitions used for redirection table entry size.
#define ETH_VLAN_STRIP_OFFLOAD 0x0001 /**< VLAN Strip On/Off */
#define ETH_VLAN_FILTER_OFFLOAD 0x0002 /**< VLAN Filter On/Off */
#define ETH_VLAN_EXTEND_OFFLOAD 0x0004 /**< VLAN Extend On/Off */
+#define ETH_QINQ_STRIP_OFFLOAD 0x0008 /**< QINQ Strip On/Off */
/* Definitions used for mask VLAN setting */
#define ETH_VLAN_STRIP_MASK 0x0001 /**< VLAN Strip setting mask */
#define ETH_VLAN_FILTER_MASK 0x0002 /**< VLAN Filter setting mask*/
#define ETH_VLAN_EXTEND_MASK 0x0004 /**< VLAN Extend setting mask*/
+#define ETH_QINQ_STRIP_MASK 0x0008 /**< QINQ Strip setting mask */
#define ETH_VLAN_ID_MAX 0x0FFF /**< VLAN ID is in lower 12 bits*/
/* Definitions used for receive MAC address */
*/
uint64_t offloads;
- /* For i40e specifically */
uint16_t pvid;
__extension__
uint8_t hw_vlan_reject_tagged : 1,
/**< If set, reject sending out untagged pkts */
hw_vlan_insert_pvid : 1;
/**< If set, enable port based VLAN insertion */
+
+ uint64_t reserved_64s[2]; /**< Reserved for future fields */
+ void *reserved_ptrs[2]; /**< Reserved for future fields */
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice.
+ *
+ * A structure used to configure an Rx packet segment to split.
+ *
+ * If RTE_ETH_RX_OFFLOAD_BUFFER_SPLIT flag is set in offloads field,
+ * the PMD will split the received packets into multiple segments
+ * according to the specification in the description array:
+ *
+ * - The first network buffer will be allocated from the memory pool,
+ * specified in the first array element, the second buffer, from the
+ * pool in the second element, and so on.
+ *
+ * - The offsets from the segment description elements specify
+ * the data offset from the buffer beginning except the first mbuf.
+ * The first segment offset is added with RTE_PKTMBUF_HEADROOM.
+ *
+ * - The lengths in the elements define the maximal data amount
+ * being received to each segment. The receiving starts with filling
+ * up the first mbuf data buffer up to specified length. If the
+ * there are data remaining (packet is longer than buffer in the first
+ * mbuf) the following data will be pushed to the next segment
+ * up to its own length, and so on.
+ *
+ * - If the length in the segment description element is zero
+ * the actual buffer size will be deduced from the appropriate
+ * memory pool properties.
+ *
+ * - If there is not enough elements to describe the buffer for entire
+ * packet of maximal length the following parameters will be used
+ * for the all remaining segments:
+ * - pool from the last valid element
+ * - the buffer size from this pool
+ * - zero offset
+ */
+struct rte_eth_rxseg_split {
+ struct rte_mempool *mp; /**< Memory pool to allocate segment from. */
+ uint16_t length; /**< Segment data length, configures split point. */
+ uint16_t offset; /**< Data offset from beginning of mbuf data buffer. */
+ uint32_t reserved; /**< Reserved field. */
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice.
+ *
+ * A common structure used to describe Rx packet segment properties.
+ */
+union rte_eth_rxseg {
+ /* The settings for buffer split offload. */
+ struct rte_eth_rxseg_split split;
+ /* The other features settings should be added here. */
};
/**
uint16_t rx_free_thresh; /**< Drives the freeing of RX descriptors. */
uint8_t rx_drop_en; /**< Drop packets if no descriptors are available. */
uint8_t rx_deferred_start; /**< Do not start queue with rte_eth_dev_start(). */
+ uint16_t rx_nseg; /**< Number of descriptions in rx_seg array. */
/**
* Per-queue Rx offloads to be set using DEV_RX_OFFLOAD_* flags.
* Only offloads set on rx_queue_offload_capa or rx_offload_capa
* fields on rte_eth_dev_info structure are allowed to be set.
*/
uint64_t offloads;
+ /**
+ * Points to the array of segment descriptions for an entire packet.
+ * Array elements are properties for consecutive Rx segments.
+ *
+ * The supported capabilities of receiving segmentation is reported
+ * in rte_eth_dev_info.rx_seg_capa field.
+ */
+ union rte_eth_rxseg *rx_seg;
+
+ uint64_t reserved_64s[2]; /**< Reserved for future fields */
+ void *reserved_ptrs[2]; /**< Reserved for future fields */
};
/**
* fields on rte_eth_dev_info structure are allowed to be set.
*/
uint64_t offloads;
+
+ uint64_t reserved_64s[2]; /**< Reserved for future fields */
+ void *reserved_ptrs[2]; /**< Reserved for future fields */
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * A structure used to return the hairpin capabilities that are supported.
+ */
+struct rte_eth_hairpin_cap {
+ /** The max number of hairpin queues (different bindings). */
+ uint16_t max_nb_queues;
+ /** Max number of Rx queues to be connected to one Tx queue. */
+ uint16_t max_rx_2_tx;
+ /** Max number of Tx queues to be connected to one Rx queue. */
+ uint16_t max_tx_2_rx;
+ uint16_t max_nb_desc; /**< The max num of descriptors. */
+};
+
+#define RTE_ETH_MAX_HAIRPIN_PEERS 32
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * A structure used to hold hairpin peer data.
+ */
+struct rte_eth_hairpin_peer {
+ uint16_t port; /**< Peer port. */
+ uint16_t queue; /**< Peer queue. */
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * A structure used to configure hairpin binding.
+ */
+struct rte_eth_hairpin_conf {
+ uint32_t peer_count:16; /**< The number of peers. */
+
+ /**
+ * Explicit Tx flow rule mode.
+ * One hairpin pair of queues should have the same attribute.
+ *
+ * - When set, the user should be responsible for inserting the hairpin
+ * Tx part flows and removing them.
+ * - When clear, the PMD will try to handle the Tx part of the flows,
+ * e.g., by splitting one flow into two parts.
+ */
+ uint32_t tx_explicit:1;
+
+ /**
+ * Manually bind hairpin queues.
+ * One hairpin pair of queues should have the same attribute.
+ *
+ * - When set, to enable hairpin, the user should call the hairpin bind
+ * function after all the queues are set up properly and the ports are
+ * started. Also, the hairpin unbind function should be called
+ * accordingly before stopping a port that with hairpin configured.
+ * - When clear, the PMD will try to enable the hairpin with the queues
+ * configured automatically during port start.
+ */
+ uint32_t manual_bind:1;
+ uint32_t reserved:14; /**< Reserved bits. */
+ struct rte_eth_hairpin_peer peers[RTE_ETH_MAX_HAIRPIN_PEERS];
};
/**
uint8_t priority; /**< VLAN User Priority. */
};
+/**
+ * Tunnel type for device-specific classifier configuration.
+ * @see rte_eth_udp_tunnel
+ */
+enum rte_eth_tunnel_type {
+ RTE_TUNNEL_TYPE_NONE = 0,
+ RTE_TUNNEL_TYPE_VXLAN,
+ RTE_TUNNEL_TYPE_GENEVE,
+ RTE_TUNNEL_TYPE_TEREDO,
+ RTE_TUNNEL_TYPE_NVGRE,
+ RTE_TUNNEL_TYPE_IP_IN_GRE,
+ RTE_L2_TUNNEL_TYPE_E_TAG,
+ RTE_TUNNEL_TYPE_VXLAN_GPE,
+ RTE_TUNNEL_TYPE_ECPRI,
+ RTE_TUNNEL_TYPE_MAX,
+};
+
+/* Deprecated API file for rte_eth_dev_filter_* functions */
+#include "rte_eth_ctrl.h"
+
/**
* Memory space that can be configured to store Flow Director filters
* in the board memory.
* A structure used to configure the Flow Director (FDIR) feature
* of an Ethernet port.
*
- * If mode is RTE_FDIR_DISABLE, the pballoc value is ignored.
+ * If mode is RTE_FDIR_MODE_NONE, the pballoc value is ignored.
*/
struct rte_fdir_conf {
enum rte_fdir_mode mode; /**< Flow Director mode. */
/**
* UDP tunneling configuration.
- * Used to config the UDP port for a type of tunnel.
- * NICs need the UDP port to identify the tunnel type.
- * Normally a type of tunnel has a default UDP port, this structure can be used
- * in case if the users want to change or support more UDP port.
+ *
+ * Used to configure the classifier of a device,
+ * associating an UDP port with a type of tunnel.
+ *
+ * Some NICs may need such configuration to properly parse a tunnel
+ * with any standard or custom UDP port.
*/
struct rte_eth_udp_tunnel {
uint16_t udp_port; /**< UDP port used for the tunnel. */
- uint8_t prot_type; /**< Tunnel type. Defined in rte_eth_tunnel_type. */
+ uint8_t prot_type; /**< Tunnel type. @see rte_eth_tunnel_type */
};
/**
/** Currently,Priority Flow Control(PFC) are supported,if DCB with PFC
is needed,and the variable must be set ETH_DCB_PFC_SUPPORT. */
uint32_t dcb_capability_en;
- struct rte_fdir_conf fdir_conf; /**< FDIR configuration. */
+ struct rte_fdir_conf fdir_conf; /**< FDIR configuration. DEPRECATED */
struct rte_intr_conf intr_conf; /**< Interrupt mode configuration. */
};
#define DEV_RX_OFFLOAD_VLAN_EXTEND 0x00000400
#define DEV_RX_OFFLOAD_JUMBO_FRAME 0x00000800
#define DEV_RX_OFFLOAD_SCATTER 0x00002000
+/**
+ * Timestamp is set by the driver in RTE_MBUF_DYNFIELD_TIMESTAMP_NAME
+ * and RTE_MBUF_DYNFLAG_RX_TIMESTAMP_NAME is set in ol_flags.
+ * The mbuf field and flag are registered when the offload is configured.
+ */
#define DEV_RX_OFFLOAD_TIMESTAMP 0x00004000
#define DEV_RX_OFFLOAD_SECURITY 0x00008000
#define DEV_RX_OFFLOAD_KEEP_CRC 0x00010000
#define DEV_RX_OFFLOAD_SCTP_CKSUM 0x00020000
#define DEV_RX_OFFLOAD_OUTER_UDP_CKSUM 0x00040000
+#define DEV_RX_OFFLOAD_RSS_HASH 0x00080000
+#define RTE_ETH_RX_OFFLOAD_BUFFER_SPLIT 0x00100000
#define DEV_RX_OFFLOAD_CHECKSUM (DEV_RX_OFFLOAD_IPV4_CKSUM | \
DEV_RX_OFFLOAD_UDP_CKSUM | \
DEV_RX_OFFLOAD_TCP_CKSUM)
#define DEV_RX_OFFLOAD_VLAN (DEV_RX_OFFLOAD_VLAN_STRIP | \
DEV_RX_OFFLOAD_VLAN_FILTER | \
- DEV_RX_OFFLOAD_VLAN_EXTEND)
+ DEV_RX_OFFLOAD_VLAN_EXTEND | \
+ DEV_RX_OFFLOAD_QINQ_STRIP)
/*
* If new Rx offload capabilities are defined, they also must be
/** Device supports outer UDP checksum */
#define DEV_TX_OFFLOAD_OUTER_UDP_CKSUM 0x00100000
/**
- * Device supports match on metadata Tx offload..
- * Application must set PKT_TX_METADATA and mbuf metadata field.
+ * Device sends on time read from RTE_MBUF_DYNFIELD_TIMESTAMP_NAME
+ * if RTE_MBUF_DYNFLAG_TX_TIMESTAMP_NAME is set in ol_flags.
+ * The mbuf field and flag are registered when the offload is configured.
*/
-#define DEV_TX_OFFLOAD_MATCH_METADATA 0x00200000
-
-#define RTE_ETH_DEV_CAPA_RUNTIME_RX_QUEUE_SETUP 0x00000001
-/**< Device supports Rx queue setup after device started*/
-#define RTE_ETH_DEV_CAPA_RUNTIME_TX_QUEUE_SETUP 0x00000002
-/**< Device supports Tx queue setup after device started*/
-
+#define DEV_TX_OFFLOAD_SEND_ON_TIMESTAMP 0x00200000
/*
* If new Tx offload capabilities are defined, they also must be
* mentioned in rte_tx_offload_names in rte_ethdev.c file.
*/
+/**@{@name Device capabilities
+ * Non-offload capabilities reported in rte_eth_dev_info.dev_capa.
+ */
+/** Device supports Rx queue setup after device started. */
+#define RTE_ETH_DEV_CAPA_RUNTIME_RX_QUEUE_SETUP 0x00000001
+/** Device supports Tx queue setup after device started. */
+#define RTE_ETH_DEV_CAPA_RUNTIME_TX_QUEUE_SETUP 0x00000002
+/**@}*/
+
/*
* Fallback default preferred Rx/Tx port parameters.
* These are used if an application requests default parameters
* Default values for switch domain id when ethdev does not support switch
* domain definitions.
*/
-#define RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID (0)
+#define RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID (UINT16_MAX)
/**
* Ethernet device associated switch information
*/
};
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice.
+ *
+ * Ethernet device Rx buffer segmentation capabilities.
+ */
+struct rte_eth_rxseg_capa {
+ __extension__
+ uint32_t multi_pools:1; /**< Supports receiving to multiple pools.*/
+ uint32_t offset_allowed:1; /**< Supports buffer offsets. */
+ uint32_t offset_align_log2:4; /**< Required offset alignment. */
+ uint16_t max_nseg; /**< Maximum amount of segments to split. */
+ uint16_t reserved; /**< Reserved field. */
+};
+
/**
* Ethernet device information
*/
+/**
+ * Ethernet device representor port type.
+ */
+enum rte_eth_representor_type {
+ RTE_ETH_REPRESENTOR_NONE, /**< not a representor. */
+ RTE_ETH_REPRESENTOR_VF, /**< representor of Virtual Function. */
+ RTE_ETH_REPRESENTOR_SF, /**< representor of Sub Function. */
+ RTE_ETH_REPRESENTOR_PF, /**< representor of Physical Function. */
+};
+
/**
* A structure used to retrieve the contextual information of
* an Ethernet device, such as the controlling driver of the
const uint32_t *dev_flags; /**< Device flags */
uint32_t min_rx_bufsize; /**< Minimum size of RX buffer. */
uint32_t max_rx_pktlen; /**< Maximum configurable length of RX pkt. */
+ /** Maximum configurable size of LRO aggregated packet. */
+ uint32_t max_lro_pkt_size;
uint16_t max_rx_queues; /**< Maximum number of RX queues. */
uint16_t max_tx_queues; /**< Maximum number of TX queues. */
uint32_t max_mac_addrs; /**< Maximum number of MAC addresses. */
/** Maximum number of hash MAC addresses for MTA and UTA. */
uint16_t max_vfs; /**< Maximum number of VFs. */
uint16_t max_vmdq_pools; /**< Maximum number of VMDq pools. */
+ struct rte_eth_rxseg_capa rx_seg_capa; /**< Segmentation capability.*/
uint64_t rx_offload_capa;
/**< All RX offload capabilities including all per-queue ones */
uint64_t tx_offload_capa;
* embedded managed interconnect/switch.
*/
struct rte_eth_switch_info switch_info;
+
+ uint64_t reserved_64s[2]; /**< Reserved for future fields */
+ void *reserved_ptrs[2]; /**< Reserved for future fields */
};
/**
struct rte_eth_rxconf conf; /**< queue config parameters. */
uint8_t scattered_rx; /**< scattered packets RX supported. */
uint16_t nb_desc; /**< configured number of RXDs. */
+ uint16_t rx_buf_size; /**< hardware receive buffer size. */
} __rte_cache_min_aligned;
/**
uint16_t nb_desc; /**< configured number of TXDs. */
} __rte_cache_min_aligned;
+/* Generic Burst mode flag definition, values can be ORed. */
+
+/**
+ * If the queues have different burst mode description, this bit will be set
+ * by PMD, then the application can iterate to retrieve burst description for
+ * all other queues.
+ */
+#define RTE_ETH_BURST_FLAG_PER_QUEUE (1ULL << 0)
+
+/**
+ * Ethernet device RX/TX queue packet burst mode information structure.
+ * Used to retrieve information about packet burst mode setting.
+ */
+struct rte_eth_burst_mode {
+ uint64_t flags; /**< The ORed values of RTE_ETH_BURST_FLAG_xxx */
+
+#define RTE_ETH_BURST_MODE_INFO_SIZE 1024 /**< Maximum size for information */
+ char info[RTE_ETH_BURST_MODE_INFO_SIZE]; /**< burst mode information */
+};
+
/** Maximum name length for extended statistics counters */
#define RTE_ETH_XSTATS_NAME_SIZE 64
* An array of this structure is returned by rte_eth_xstats_get_names().
* It lists the names of extended statistics for a PMD. The *rte_eth_xstat*
* structure references these names by their array index.
+ *
+ * The xstats should follow a common naming scheme.
+ * Some names are standardized in rte_stats_strings.
+ * Examples:
+ * - rx_missed_errors
+ * - tx_q3_bytes
+ * - tx_size_128_to_255_packets
*/
struct rte_eth_xstat_name {
char name[RTE_ETH_XSTATS_NAME_SIZE]; /**< The statistic name. */
struct rte_eth_dcb_tc_queue_mapping {
/** rx queues assigned to tc per Pool */
struct {
- uint8_t base;
- uint8_t nb_queue;
+ uint16_t base;
+ uint16_t nb_queue;
} tc_rxq[ETH_MAX_VMDQ_POOL][ETH_DCB_NUM_TCS];
/** rx queues assigned to tc per Pool */
struct {
- uint8_t base;
- uint8_t nb_queue;
+ uint16_t base;
+ uint16_t nb_queue;
} tc_txq[ETH_MAX_VMDQ_POOL][ETH_DCB_NUM_TCS];
};
};
/**
- * RX/TX queue states
+ * This enum indicates the possible Forward Error Correction (FEC) modes
+ * of an ethdev port.
*/
-#define RTE_ETH_QUEUE_STATE_STOPPED 0
-#define RTE_ETH_QUEUE_STATE_STARTED 1
+enum rte_eth_fec_mode {
+ RTE_ETH_FEC_NOFEC = 0, /**< FEC is off */
+ RTE_ETH_FEC_AUTO, /**< FEC autonegotiation modes */
+ RTE_ETH_FEC_BASER, /**< FEC using common algorithm */
+ RTE_ETH_FEC_RS, /**< FEC using RS algorithm */
+};
+
+/* Translate from FEC mode to FEC capa */
+#define RTE_ETH_FEC_MODE_TO_CAPA(x) (1U << (x))
+
+/* This macro indicates FEC capa mask */
+#define RTE_ETH_FEC_MODE_CAPA_MASK(x) (1U << (RTE_ETH_FEC_ ## x))
+
+/* A structure used to get capabilities per link speed */
+struct rte_eth_fec_capa {
+ uint32_t speed; /**< Link speed (see ETH_SPEED_NUM_*) */
+ uint32_t capa; /**< FEC capabilities bitmask */
+};
#define RTE_ETH_ALL RTE_MAX_ETHPORTS
char name[RTE_ETH_MAX_OWNER_NAME_LEN]; /**< The owner name. */
};
-/**
- * Port is released (i.e. totally freed and data erased) on close.
- * Temporary flag for PMD migration to new rte_eth_dev_close() behaviour.
- */
-#define RTE_ETH_DEV_CLOSE_REMOVE 0x0001
+/** PMD supports thread-safe flow operations */
+#define RTE_ETH_DEV_FLOW_OPS_THREAD_SAFE 0x0001
/** Device supports link state interrupt */
#define RTE_ETH_DEV_INTR_LSC 0x0002
/** Device is a bonded slave */
#define RTE_ETH_DEV_REPRESENTOR 0x0010
/** Device does not support MAC change after started */
#define RTE_ETH_DEV_NOLIVE_MAC_ADDR 0x0020
+/**
+ * Queue xstats filled automatically by ethdev layer.
+ * PMDs filling the queue xstats themselves should not set this flag
+ */
+#define RTE_ETH_DEV_AUTOFILL_QUEUE_XSTATS 0x0040
/**
* Iterates over valid ethdev ports owned by a specific owner.
* Next port id of the device, possibly port_id_start,
* RTE_MAX_ETHPORTS if there is none.
*/
-uint16_t __rte_experimental
+__rte_experimental
+uint16_t
rte_eth_find_next_of(uint16_t port_id_start,
const struct rte_device *parent);
* Next sibling port id, possibly port_id_start or ref_port_id itself,
* RTE_MAX_ETHPORTS if there is none.
*/
-uint16_t __rte_experimental
-rte_eth_find_next_sibling(uint16_t port_id_start,
- uint16_t ref_port_id);
+__rte_experimental
+uint16_t
+rte_eth_find_next_sibling(uint16_t port_id_start, uint16_t ref_port_id);
/**
* Macro to iterate over all ethdev ports sharing the same rte_device
* @return
* Negative errno value on error, 0 on success.
*/
-int __rte_experimental rte_eth_dev_owner_new(uint64_t *owner_id);
+__rte_experimental
+int rte_eth_dev_owner_new(uint64_t *owner_id);
/**
* @warning
* @return
* Negative errno value on error, 0 on success.
*/
-int __rte_experimental rte_eth_dev_owner_set(const uint16_t port_id,
+__rte_experimental
+int rte_eth_dev_owner_set(const uint16_t port_id,
const struct rte_eth_dev_owner *owner);
/**
* @return
* 0 on success, negative errno value on error.
*/
-int __rte_experimental rte_eth_dev_owner_unset(const uint16_t port_id,
+__rte_experimental
+int rte_eth_dev_owner_unset(const uint16_t port_id,
const uint64_t owner_id);
/**
*
* @param owner_id
* The owner identifier.
+ * @return
+ * 0 on success, negative errno value on error.
*/
-void __rte_experimental rte_eth_dev_owner_delete(const uint64_t owner_id);
+__rte_experimental
+int rte_eth_dev_owner_delete(const uint64_t owner_id);
/**
* @warning
* @return
* 0 on success, negative errno value on error..
*/
-int __rte_experimental rte_eth_dev_owner_get(const uint16_t port_id,
+__rte_experimental
+int rte_eth_dev_owner_get(const uint16_t port_id,
struct rte_eth_dev_owner *owner);
-/**
- * Get the total number of Ethernet devices that have been successfully
- * initialized by the matching Ethernet driver during the PCI probing phase
- * and that are available for applications to use. These devices must be
- * accessed by using the ``RTE_ETH_FOREACH_DEV()`` macro to deal with
- * non-contiguous ranges of devices.
- * These non-contiguous ranges can be created by calls to hotplug functions or
- * by some PMDs.
- *
- * @return
- * - The total number of usable Ethernet devices.
- */
-__rte_deprecated
-uint16_t rte_eth_dev_count(void);
-
/**
* Get the number of ports which are usable for the application.
*
* @return
* The total count of Ethernet devices.
*/
-uint16_t __rte_experimental rte_eth_dev_count_total(void);
+uint16_t rte_eth_dev_count_total(void);
/**
* Convert a numerical speed in Mbps to a bitmap flag that can be used in
* @return
* 1 when the Ethernet device is removed, otherwise 0.
*/
-int __rte_experimental
+__rte_experimental
+int
rte_eth_dev_is_removed(uint16_t port_id);
/**
* No need to repeat any bit in rx_conf->offloads which has already been
* enabled in rte_eth_dev_configure() at port level. An offloading enabled
* at port level can't be disabled at queue level.
+ * The configuration structure also contains the pointer to the array
+ * of the receiving buffer segment descriptions, see rx_seg and rx_nseg
+ * fields, this extended configuration might be used by split offloads like
+ * RTE_ETH_RX_OFFLOAD_BUFFER_SPLIT. If mp_pool is not NULL,
+ * the extended configuration fields must be set to NULL and zero.
* @param mb_pool
* The pointer to the memory pool from which to allocate *rte_mbuf* network
- * memory buffers to populate each descriptor of the receive ring.
+ * memory buffers to populate each descriptor of the receive ring. There are
+ * two options to provide Rx buffer configuration:
+ * - single pool:
+ * mb_pool is not NULL, rx_conf.rx_nseg is 0.
+ * - multiple segments description:
+ * mb_pool is NULL, rx_conf.rx_seg is not NULL, rx_conf.rx_nseg is not 0.
+ * Taken only if flag RTE_ETH_RX_OFFLOAD_BUFFER_SPLIT is set in offloads.
+ *
* @return
* - 0: Success, receive queue correctly set up.
* - -EIO: if device is removed.
- * - -EINVAL: The size of network buffers which can be allocated from the
- * memory pool does not fit the various buffer sizes allowed by the
- * device controller.
+ * - -ENODEV: if *port_id* is invalid.
+ * - -EINVAL: The memory pool pointer is null or the size of network buffers
+ * which can be allocated from this memory pool does not fit the various
+ * buffer sizes allowed by the device controller.
* - -ENOMEM: Unable to allocate the receive ring descriptors or to
* allocate network memory buffers from the memory pool when
* initializing receive descriptors.
const struct rte_eth_rxconf *rx_conf,
struct rte_mempool *mb_pool);
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Allocate and set up a hairpin receive queue for an Ethernet device.
+ *
+ * The function set up the selected queue to be used in hairpin.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param rx_queue_id
+ * The index of the receive queue to set up.
+ * The value must be in the range [0, nb_rx_queue - 1] previously supplied
+ * to rte_eth_dev_configure().
+ * @param nb_rx_desc
+ * The number of receive descriptors to allocate for the receive ring.
+ * 0 means the PMD will use default value.
+ * @param conf
+ * The pointer to the hairpin configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if *port_id* is invalid.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ * - (-ENOMEM) if unable to allocate the resources.
+ */
+__rte_experimental
+int rte_eth_rx_hairpin_queue_setup
+ (uint16_t port_id, uint16_t rx_queue_id, uint16_t nb_rx_desc,
+ const struct rte_eth_hairpin_conf *conf);
+
/**
* Allocate and set up a transmit queue for an Ethernet device.
*
uint16_t nb_tx_desc, unsigned int socket_id,
const struct rte_eth_txconf *tx_conf);
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Allocate and set up a transmit hairpin queue for an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param tx_queue_id
+ * The index of the transmit queue to set up.
+ * The value must be in the range [0, nb_tx_queue - 1] previously supplied
+ * to rte_eth_dev_configure().
+ * @param nb_tx_desc
+ * The number of transmit descriptors to allocate for the transmit ring.
+ * 0 to set default PMD value.
+ * @param conf
+ * The hairpin configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if *port_id* is invalid.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ * - (-ENOMEM) if unable to allocate the resources.
+ */
+__rte_experimental
+int rte_eth_tx_hairpin_queue_setup
+ (uint16_t port_id, uint16_t tx_queue_id, uint16_t nb_tx_desc,
+ const struct rte_eth_hairpin_conf *conf);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Get all the hairpin peer Rx / Tx ports of the current port.
+ * The caller should ensure that the array is large enough to save the ports
+ * list.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param peer_ports
+ * Pointer to the array to store the peer ports list.
+ * @param len
+ * Length of the array to store the port identifiers.
+ * @param direction
+ * Current port to peer port direction
+ * positive - current used as Tx to get all peer Rx ports.
+ * zero - current used as Rx to get all peer Tx ports.
+ *
+ * @return
+ * - (0 or positive) actual peer ports number.
+ * - (-EINVAL) if bad parameter.
+ * - (-ENODEV) if *port_id* invalid
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - Others detailed errors from PMD drivers.
+ */
+__rte_experimental
+int rte_eth_hairpin_get_peer_ports(uint16_t port_id, uint16_t *peer_ports,
+ size_t len, uint32_t direction);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Bind all hairpin Tx queues of one port to the Rx queues of the peer port.
+ * It is only allowed to call this function after all hairpin queues are
+ * configured properly and the devices are in started state.
+ *
+ * @param tx_port
+ * The identifier of the Tx port.
+ * @param rx_port
+ * The identifier of peer Rx port.
+ * RTE_MAX_ETHPORTS is allowed for the traversal of all devices.
+ * Rx port ID could have the same value as Tx port ID.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if Tx port ID is invalid.
+ * - (-EBUSY) if device is not in started state.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - Others detailed errors from PMD drivers.
+ */
+__rte_experimental
+int rte_eth_hairpin_bind(uint16_t tx_port, uint16_t rx_port);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Unbind all hairpin Tx queues of one port from the Rx queues of the peer port.
+ * This should be called before closing the Tx or Rx devices, if the bind
+ * function is called before.
+ * After unbinding the hairpin ports pair, it is allowed to bind them again.
+ * Changing queues configuration should be after stopping the device(s).
+ *
+ * @param tx_port
+ * The identifier of the Tx port.
+ * @param rx_port
+ * The identifier of peer Rx port.
+ * RTE_MAX_ETHPORTS is allowed for traversal of all devices.
+ * Rx port ID could have the same value as Tx port ID.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if Tx port ID is invalid.
+ * - (-EBUSY) if device is in stopped state.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - Others detailed errors from PMD drivers.
+ */
+__rte_experimental
+int rte_eth_hairpin_unbind(uint16_t tx_port, uint16_t rx_port);
+
/**
* Return the NUMA socket to which an Ethernet device is connected
*
* to rte_eth_dev_configure().
* @return
* - 0: Success, the receive queue is started.
- * - -EINVAL: The port_id or the queue_id out of range.
+ * - -ENODEV: if *port_id* is invalid.
+ * - -EINVAL: The queue_id out of range or belong to hairpin.
* - -EIO: if device is removed.
* - -ENOTSUP: The function not supported in PMD driver.
*/
* to rte_eth_dev_configure().
* @return
* - 0: Success, the receive queue is stopped.
- * - -EINVAL: The port_id or the queue_id out of range.
+ * - -ENODEV: if *port_id* is invalid.
+ * - -EINVAL: The queue_id out of range or belong to hairpin.
* - -EIO: if device is removed.
* - -ENOTSUP: The function not supported in PMD driver.
*/
* to rte_eth_dev_configure().
* @return
* - 0: Success, the transmit queue is started.
- * - -EINVAL: The port_id or the queue_id out of range.
+ * - -ENODEV: if *port_id* is invalid.
+ * - -EINVAL: The queue_id out of range or belong to hairpin.
* - -EIO: if device is removed.
* - -ENOTSUP: The function not supported in PMD driver.
*/
* to rte_eth_dev_configure().
* @return
* - 0: Success, the transmit queue is stopped.
- * - -EINVAL: The port_id or the queue_id out of range.
+ * - -ENODEV: if *port_id* is invalid.
+ * - -EINVAL: The queue_id out of range or belong to hairpin.
* - -EIO: if device is removed.
* - -ENOTSUP: The function not supported in PMD driver.
*/
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - 0: Success, Ethernet device stopped.
+ * - <0: Error code of the driver device stop function.
*/
-void rte_eth_dev_stop(uint16_t port_id);
+int rte_eth_dev_stop(uint16_t port_id);
/**
* Link up an Ethernet device.
/**
* Close a stopped Ethernet device. The device cannot be restarted!
- * The function frees all port resources if the driver supports
- * the flag RTE_ETH_DEV_CLOSE_REMOVE.
+ * The function frees all port resources.
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - Zero if the port is closed successfully.
+ * - Negative if something went wrong.
*/
-void rte_eth_dev_close(uint16_t port_id);
+int rte_eth_dev_close(uint16_t port_id);
/**
* Reset a Ethernet device and keep its port id.
*
* @return
* - (0) if successful.
- * - (-EINVAL) if port identifier is invalid.
+ * - (-ENODEV) if *port_id* is invalid.
* - (-ENOTSUP) if hardware doesn't support this function.
* - (-EPERM) if not ran from the primary process.
* - (-EIO) if re-initialisation failed or device is removed.
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if support for promiscuous_enable() does not exist
+ * for the device.
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_promiscuous_enable(uint16_t port_id);
+int rte_eth_promiscuous_enable(uint16_t port_id);
/**
* Disable receipt in promiscuous mode for an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if support for promiscuous_disable() does not exist
+ * for the device.
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_promiscuous_disable(uint16_t port_id);
+int rte_eth_promiscuous_disable(uint16_t port_id);
/**
* Return the value of promiscuous mode for an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if support for allmulticast_enable() does not exist
+ * for the device.
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_allmulticast_enable(uint16_t port_id);
+int rte_eth_allmulticast_enable(uint16_t port_id);
/**
* Disable the receipt of all multicast frames by an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if support for allmulticast_disable() does not exist
+ * for the device.
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_allmulticast_disable(uint16_t port_id);
+int rte_eth_allmulticast_disable(uint16_t port_id);
/**
* Return the value of allmulticast mode for an Ethernet device.
int rte_eth_allmulticast_get(uint16_t port_id);
/**
- * Retrieve the status (ON/OFF), the speed (in Mbps) and the mode (HALF-DUPLEX
- * or FULL-DUPLEX) of the physical link of an Ethernet device. It might need
- * to wait up to 9 seconds in it.
+ * Retrieve the link status (up/down), the duplex mode (half/full),
+ * the negotiation (auto/fixed), and if available, the speed (Mbps).
+ *
+ * It might need to wait up to 9 seconds.
+ * @see rte_eth_link_get_nowait.
*
* @param port_id
* The port identifier of the Ethernet device.
* @param link
- * A pointer to an *rte_eth_link* structure to be filled with
- * the status, the speed and the mode of the Ethernet device link.
+ * Link information written back.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if the function is not supported in PMD driver.
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_link_get(uint16_t port_id, struct rte_eth_link *link);
+int rte_eth_link_get(uint16_t port_id, struct rte_eth_link *link);
/**
- * Retrieve the status (ON/OFF), the speed (in Mbps) and the mode (HALF-DUPLEX
- * or FULL-DUPLEX) of the physical link of an Ethernet device. It is a no-wait
- * version of rte_eth_link_get().
+ * Retrieve the link status (up/down), the duplex mode (half/full),
+ * the negotiation (auto/fixed), and if available, the speed (Mbps).
*
* @param port_id
* The port identifier of the Ethernet device.
* @param link
- * A pointer to an *rte_eth_link* structure to be filled with
- * the status, the speed and the mode of the Ethernet device link.
+ * Link information written back.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if the function is not supported in PMD driver.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+int rte_eth_link_get_nowait(uint16_t port_id, struct rte_eth_link *link);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * The function converts a link_speed to a string. It handles all special
+ * values like unknown or none speed.
+ *
+ * @param link_speed
+ * link_speed of rte_eth_link struct
+ * @return
+ * Link speed in textual format. It's pointer to immutable memory.
+ * No free is required.
*/
-void rte_eth_link_get_nowait(uint16_t port_id, struct rte_eth_link *link);
+__rte_experimental
+const char *rte_eth_link_speed_to_str(uint32_t link_speed);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * The function converts a rte_eth_link struct representing a link status to
+ * a string.
+ *
+ * @param str
+ * A pointer to a string to be filled with textual representation of
+ * device status. At least ETH_LINK_MAX_STR_LEN bytes should be allocated to
+ * store default link status text.
+ * @param len
+ * Length of available memory at 'str' string.
+ * @param eth_link
+ * Link status returned by rte_eth_link_get function
+ * @return
+ * Number of bytes written to str array.
+ */
+__rte_experimental
+int rte_eth_link_to_str(char *str, size_t len,
+ const struct rte_eth_link *eth_link);
/**
* Retrieve the general I/O statistics of an Ethernet device.
* - (0) if device notified to reset stats.
* - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
+ * - (<0): Error code of the driver stats reset function.
*/
int rte_eth_stats_reset(uint16_t port_id);
* A pointer to an ids array passed by application. This tells which
* statistics values function should retrieve. This parameter
* can be set to NULL if size is 0. In this case function will retrieve
- * all avalible statistics.
+ * all available statistics.
* @param values
* A pointer to a table to be filled with device statistics values.
* @param size
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @return
+ * - (0) if device notified to reset extended stats.
+ * - (-ENOTSUP) if pmd doesn't support both
+ * extended stats and basic stats reset.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (<0): Error code of the driver xstats reset function.
*/
-void rte_eth_xstats_reset(uint16_t port_id);
+int rte_eth_xstats_reset(uint16_t port_id);
/**
* Set a mapping for the specified transmit queue to the specified per-queue
* The per-queue packet statistics functionality number that the transmit
* queue is to be assigned.
* The value must be in the range [0, RTE_ETHDEV_QUEUE_STAT_CNTRS - 1].
+ * Max RTE_ETHDEV_QUEUE_STAT_CNTRS being 256.
* @return
* Zero if successful. Non-zero otherwise.
*/
* The per-queue packet statistics functionality number that the receive
* queue is to be assigned.
* The value must be in the range [0, RTE_ETHDEV_QUEUE_STAT_CNTRS - 1].
+ * Max RTE_ETHDEV_QUEUE_STAT_CNTRS being 256.
* @return
* Zero if successful. Non-zero otherwise.
*/
* @param mac_addr
* A pointer to a structure of type *ether_addr* to be filled with
* the Ethernet address of the Ethernet device.
+ * @return
+ * - (0) if successful
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_macaddr_get(uint16_t port_id, struct ether_addr *mac_addr);
+int rte_eth_macaddr_get(uint16_t port_id, struct rte_ether_addr *mac_addr);
/**
* Retrieve the contextual information of an Ethernet device.
* .nb_max = UINT16_MAX,
* .nb_min = 0,
* .nb_align = 1,
+ * .nb_seg_max = UINT16_MAX,
+ * .nb_mtu_seg_max = UINT16_MAX,
* };
*
* device = dev->device
- * min_mtu = ETHER_MIN_MTU
+ * min_mtu = RTE_ETHER_MIN_MTU
* max_mtu = UINT16_MAX
*
* The following fields will be populated if support for dev_infos_get()
* @param dev_info
* A pointer to a structure of type *rte_eth_dev_info* to be filled with
* the contextual information of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if support for dev_infos_get() does not exist for the device.
+ * - (-ENODEV) if *port_id* invalid.
*/
-void rte_eth_dev_info_get(uint16_t port_id, struct rte_eth_dev_info *dev_info);
+int rte_eth_dev_info_get(uint16_t port_id, struct rte_eth_dev_info *dev_info);
/**
* Retrieve the firmware version of a device.
*/
int rte_eth_dev_get_supported_ptypes(uint16_t port_id, uint32_t ptype_mask,
uint32_t *ptypes, int num);
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * Inform Ethernet device about reduced range of packet types to handle.
+ *
+ * Application can use this function to set only specific ptypes that it's
+ * interested. This information can be used by the PMD to optimize Rx path.
+ *
+ * The function accepts an array `set_ptypes` allocated by the caller to
+ * store the packet types set by the driver, the last element of the array
+ * is set to RTE_PTYPE_UNKNOWN. The size of the `set_ptype` array should be
+ * `rte_eth_dev_get_supported_ptypes() + 1` else it might only be filled
+ * partially.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param ptype_mask
+ * The ptype family that application is interested in should be bitwise OR of
+ * RTE_PTYPE_*_MASK or 0.
+ * @param set_ptypes
+ * An array pointer to store set packet types, allocated by caller. The
+ * function marks the end of array with RTE_PTYPE_UNKNOWN.
+ * @param num
+ * Size of the array pointed by param ptypes.
+ * Should be rte_eth_dev_get_supported_ptypes() + 1 to accommodate the
+ * set ptypes.
+ * @return
+ * - (0) if Success.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if *ptype_mask* is invalid (or) set_ptypes is NULL and
+ * num > 0.
+ */
+__rte_experimental
+int rte_eth_dev_set_ptypes(uint16_t port_id, uint32_t ptype_mask,
+ uint32_t *set_ptypes, unsigned int num);
/**
* Retrieve the MTU of an Ethernet device.
* Otherwise, disable VLAN filtering of VLAN packets tagged with *vlan_id*.
* @return
* - (0) if successful.
- * - (-ENOSUP) if hardware-assisted VLAN filtering not configured.
+ * - (-ENOTSUP) if hardware-assisted VLAN filtering not configured.
* - (-ENODEV) if *port_id* invalid.
* - (-EIO) if device is removed.
* - (-ENOSYS) if VLAN filtering on *port_id* disabled.
/**
* Enable/Disable hardware VLAN Strip by a rx queue of an Ethernet device.
- * 82599/X540/X550 can support VLAN stripping at the rx queue level
*
* @param port_id
* The port identifier of the Ethernet device.
* If 0, Disable VLAN Stripping of the receive queue of the Ethernet port.
* @return
* - (0) if successful.
- * - (-ENOSUP) if hardware-assisted VLAN stripping not configured.
+ * - (-ENOTSUP) if hardware-assisted VLAN stripping not configured.
* - (-ENODEV) if *port_id* invalid.
* - (-EINVAL) if *rx_queue_id* invalid.
*/
/**
* Set the Outer VLAN Ether Type by an Ethernet device, it can be inserted to
- * the VLAN Header. This is a register setup available on some Intel NIC, not
- * but all, please check the data sheet for availability.
+ * the VLAN header.
*
* @param port_id
* The port identifier of the Ethernet device.
* The Tag Protocol ID
* @return
* - (0) if successful.
- * - (-ENOSUP) if hardware-assisted VLAN TPID setup is not supported.
+ * - (-ENOTSUP) if hardware-assisted VLAN TPID setup is not supported.
* - (-ENODEV) if *port_id* invalid.
* - (-EIO) if device is removed.
*/
uint16_t tag_type);
/**
- * Set VLAN offload configuration on an Ethernet device
- * Enable/Disable Extended VLAN by an Ethernet device, This is a register setup
- * available on some Intel NIC, not but all, please check the data sheet for
- * availability.
- * Enable/Disable VLAN Strip can be done on rx queue for certain NIC, but here
- * the configuration is applied on the port level.
+ * Set VLAN offload configuration on an Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
* ETH_VLAN_STRIP_OFFLOAD
* ETH_VLAN_FILTER_OFFLOAD
* ETH_VLAN_EXTEND_OFFLOAD
+ * ETH_QINQ_STRIP_OFFLOAD
* @return
* - (0) if successful.
- * - (-ENOSUP) if hardware-assisted VLAN filtering not configured.
+ * - (-ENOTSUP) if hardware-assisted VLAN filtering not configured.
* - (-ENODEV) if *port_id* invalid.
* - (-EIO) if device is removed.
*/
* ETH_VLAN_STRIP_OFFLOAD
* ETH_VLAN_FILTER_OFFLOAD
* ETH_VLAN_EXTEND_OFFLOAD
+ * ETH_QINQ_STRIP_OFFLOAD
* - (-ENODEV) if *port_id* invalid.
*/
int rte_eth_dev_get_vlan_offload(uint16_t port_id);
/**
* Request the driver to free mbufs currently cached by the driver. The
* driver will only free the mbuf if it is no longer in use. It is the
- * application's responsibity to ensure rte_eth_tx_buffer_flush(..) is
+ * application's responsibility to ensure rte_eth_tx_buffer_flush(..) is
* called if needed.
*
* @param port_id
RTE_ETH_EVENT_NEW, /**< port is probed */
RTE_ETH_EVENT_DESTROY, /**< port is released */
RTE_ETH_EVENT_IPSEC, /**< IPsec offload related event */
+ RTE_ETH_EVENT_FLOW_AGED,/**< New aged-out flows is detected */
RTE_ETH_EVENT_MAX /**< max value of this enum */
};
* successful.
* - (-1) on error.
*/
-int __rte_experimental
+__rte_experimental
+int
rte_eth_dev_rx_intr_ctl_q_get_fd(uint16_t port_id, uint16_t queue_id);
/**
*/
int rte_eth_led_off(uint16_t port_id);
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Get Forward Error Correction(FEC) capability.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param speed_fec_capa
+ * speed_fec_capa is out only with per-speed capabilities.
+ * If set to NULL, the function returns the required number
+ * of required array entries.
+ * @param num
+ * a number of elements in an speed_fec_capa array.
+ *
+ * @return
+ * - A non-negative value lower or equal to num: success. The return value
+ * is the number of entries filled in the fec capa array.
+ * - A non-negative value higher than num: error, the given fec capa array
+ * is too small. The return value corresponds to the num that should
+ * be given to succeed. The entries in fec capa array are not valid and
+ * shall not be used by the caller.
+ * - (-ENOTSUP) if underlying hardware OR driver doesn't support.
+ * that operation.
+ * - (-EIO) if device is removed.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if *num* or *speed_fec_capa* invalid
+ */
+__rte_experimental
+int rte_eth_fec_get_capability(uint16_t port_id,
+ struct rte_eth_fec_capa *speed_fec_capa,
+ unsigned int num);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Get current Forward Error Correction(FEC) mode.
+ * If link is down and AUTO is enabled, AUTO is returned, otherwise,
+ * configured FEC mode is returned.
+ * If link is up, current FEC mode is returned.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param fec_capa
+ * A bitmask of enabled FEC modes. If AUTO bit is set, other
+ * bits specify FEC modes which may be negotiated. If AUTO
+ * bit is clear, specify FEC modes to be used (only one valid
+ * mode per speed may be set).
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if underlying hardware OR driver doesn't support.
+ * that operation.
+ * - (-EIO) if device is removed.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+__rte_experimental
+int rte_eth_fec_get(uint16_t port_id, uint32_t *fec_capa);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Set Forward Error Correction(FEC) mode.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param fec_capa
+ * A bitmask of allowed FEC modes. If AUTO bit is set, other
+ * bits specify FEC modes which may be negotiated. If AUTO
+ * bit is clear, specify FEC modes to be used (only one valid
+ * mode per speed may be set).
+ * @return
+ * - (0) if successful.
+ * - (-EINVAL) if the FEC mode is not valid.
+ * - (-ENOTSUP) if underlying hardware OR driver doesn't support.
+ * - (-EIO) if device is removed.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+__rte_experimental
+int rte_eth_fec_set(uint16_t port_id, uint32_t fec_capa);
+
/**
* Get current status of the Ethernet link flow control for Ethernet device
*
struct rte_eth_pfc_conf *pfc_conf);
/**
- * Add a MAC address to an internal array of addresses used to enable whitelist
- * filtering to accept packets only if the destination MAC address matches.
+ * Add a MAC address to the set used for filtering incoming packets.
*
* @param port_id
* The port identifier of the Ethernet device.
* - (-ENOSPC) if no more MAC addresses can be added.
* - (-EINVAL) if MAC address is invalid.
*/
-int rte_eth_dev_mac_addr_add(uint16_t port_id, struct ether_addr *mac_addr,
+int rte_eth_dev_mac_addr_add(uint16_t port_id, struct rte_ether_addr *mac_addr,
uint32_t pool);
/**
* - (-ENODEV) if *port* invalid.
* - (-EADDRINUSE) if attempting to remove the default MAC address
*/
-int rte_eth_dev_mac_addr_remove(uint16_t port_id, struct ether_addr *mac_addr);
+int rte_eth_dev_mac_addr_remove(uint16_t port_id,
+ struct rte_ether_addr *mac_addr);
/**
* Set the default MAC address.
* - (-EINVAL) if MAC address is invalid.
*/
int rte_eth_dev_default_mac_addr_set(uint16_t port_id,
- struct ether_addr *mac_addr);
+ struct rte_ether_addr *mac_addr);
/**
* Update Redirection Table(RETA) of Receive Side Scaling of Ethernet device.
* rte_eth_dev_info_get().
* @return
* - (0) if successful.
+ * - (-ENODEV) if *port_id* is invalid.
* - (-ENOTSUP) if hardware doesn't support.
* - (-EINVAL) if bad parameter.
* - (-EIO) if device is removed.
struct rte_eth_rss_reta_entry64 *reta_conf,
uint16_t reta_size);
- /**
+/**
* Query Redirection Table(RETA) of Receive Side Scaling of Ethernet device.
*
* @param port_id
* The port identifier of the Ethernet device.
* @param reta_conf
- * RETA to query.
+ * RETA to query. For each requested reta entry, corresponding bit
+ * in mask must be set.
* @param reta_size
* Redirection table size. The table size can be queried by
* rte_eth_dev_info_get().
* @return
* - (0) if successful.
+ * - (-ENODEV) if *port_id* is invalid.
* - (-ENOTSUP) if hardware doesn't support.
* - (-EINVAL) if bad parameter.
* - (-EIO) if device is removed.
struct rte_eth_rss_reta_entry64 *reta_conf,
uint16_t reta_size);
- /**
+/**
* Updates unicast hash table for receiving packet with the given destination
* MAC address, and the packet is routed to all VFs for which the RX mode is
* accept packets that match the unicast hash table.
* - (-EIO) if device is removed.
* - (-EINVAL) if bad parameter.
*/
-int rte_eth_dev_uc_hash_table_set(uint16_t port_id, struct ether_addr *addr,
+int rte_eth_dev_uc_hash_table_set(uint16_t port_id, struct rte_ether_addr *addr,
uint8_t on);
- /**
+/**
* Updates all unicast hash bitmaps for receiving packet with any Unicast
* Ethernet MAC addresses,the packet is routed to all VFs for which the RX
* mode is accept packets that match the unicast hash table.
int rte_eth_set_queue_rate_limit(uint16_t port_id, uint16_t queue_idx,
uint16_t tx_rate);
- /**
+/**
* Configuration of Receive Side Scaling hash computation of Ethernet device.
*
* @param port_id
int rte_eth_dev_rss_hash_update(uint16_t port_id,
struct rte_eth_rss_conf *rss_conf);
- /**
+/**
* Retrieve current configuration of Receive Side Scaling hash computation
* of Ethernet device.
*
rte_eth_dev_rss_hash_conf_get(uint16_t port_id,
struct rte_eth_rss_conf *rss_conf);
- /**
- * Add UDP tunneling port for a specific type of tunnel.
- * The packets with this UDP port will be identified as this type of tunnel.
- * Before enabling any offloading function for a tunnel, users can call this API
- * to change or add more UDP port for the tunnel. So the offloading function
- * can take effect on the packets with the specific UDP port.
+/**
+ * Add UDP tunneling port for a type of tunnel.
+ *
+ * Some NICs may require such configuration to properly parse a tunnel
+ * with any standard or custom UDP port.
+ * The packets with this UDP port will be parsed for this type of tunnel.
+ * The device parser will also check the rest of the tunnel headers
+ * before classifying the packet.
+ *
+ * With some devices, this API will affect packet classification, i.e.:
+ * - mbuf.packet_type reported on Rx
+ * - rte_flow rules with tunnel items
*
* @param port_id
* The port identifier of the Ethernet device.
rte_eth_dev_udp_tunnel_port_add(uint16_t port_id,
struct rte_eth_udp_tunnel *tunnel_udp);
- /**
- * Delete UDP tunneling port a specific type of tunnel.
- * The packets with this UDP port will not be identified as this type of tunnel
- * any more.
- * Before enabling any offloading function for a tunnel, users can call this API
- * to delete a UDP port for the tunnel. So the offloading function will not take
- * effect on the packets with the specific UDP port.
+/**
+ * Delete UDP tunneling port for a type of tunnel.
+ *
+ * The packets with this UDP port will not be classified as this type of tunnel
+ * anymore if the device use such mapping for tunnel packet classification.
+ *
+ * @see rte_eth_dev_udp_tunnel_port_add
*
* @param port_id
* The port identifier of the Ethernet device.
rte_eth_dev_udp_tunnel_port_delete(uint16_t port_id,
struct rte_eth_udp_tunnel *tunnel_udp);
-/**
- * Check whether the filter type is supported on an Ethernet device.
- * All the supported filter types are defined in 'rte_eth_ctrl.h'.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param filter_type
- * Filter type.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support this filter type.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EIO) if device is removed.
- */
-int rte_eth_dev_filter_supported(uint16_t port_id,
- enum rte_filter_type filter_type);
-
-/**
- * Take operations to assigned filter type on an Ethernet device.
- * All the supported operations and filter types are defined in 'rte_eth_ctrl.h'.
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param filter_type
- * Filter type.
- * @param filter_op
- * Type of operation.
- * @param arg
- * A pointer to arguments defined specifically for the operation.
- * @return
- * - (0) if successful.
- * - (-ENOTSUP) if hardware doesn't support.
- * - (-ENODEV) if *port_id* invalid.
- * - (-EIO) if device is removed.
- * - others depends on the specific operations implementation.
- */
-int rte_eth_dev_filter_ctrl(uint16_t port_id, enum rte_filter_type filter_type,
- enum rte_filter_op filter_op, void *arg);
-
/**
* Get DCB information on an Ethernet device.
*
* The callback function
* @param user_param
* A generic pointer parameter which will be passed to each invocation of the
- * callback function on this port and queue.
+ * callback function on this port and queue. Inter-thread synchronization
+ * of any user data changes is the responsibility of the user.
*
* @return
* NULL on error.
* The callback function
* @param user_param
* A generic pointer parameter which will be passed to each invocation of the
- * callback function on this port and queue.
+ * callback function on this port and queue. Inter-thread synchronization
+ * of any user data changes is the responsibility of the user.
*
* @return
* NULL on error.
* The callback function
* @param user_param
* A generic pointer parameter which will be passed to each invocation of the
- * callback function on this port and queue.
+ * callback function on this port and queue. Inter-thread synchronization
+ * of any user data changes is the responsibility of the user.
*
* @return
* NULL on error.
* on that queue.
*
* - After a short delay - where the delay is sufficient to allow any
- * in-flight callbacks to complete.
+ * in-flight callbacks to complete. Alternately, the RCU mechanism can be
+ * used to detect when data plane threads have ceased referencing the
+ * callback memory.
*
* @param port_id
* The port identifier of the Ethernet device.
*
* @return
* - 0: Success. Callback was removed.
+ * - -ENODEV: If *port_id* is invalid.
* - -ENOTSUP: Callback support is not available.
- * - -EINVAL: The port_id or the queue_id is out of range, or the callback
+ * - -EINVAL: The queue_id is out of range, or the callback
* is NULL or not found for the port/queue.
*/
int rte_eth_remove_rx_callback(uint16_t port_id, uint16_t queue_id,
* on that queue.
*
* - After a short delay - where the delay is sufficient to allow any
- * in-flight callbacks to complete.
+ * in-flight callbacks to complete. Alternately, the RCU mechanism can be
+ * used to detect when data plane threads have ceased referencing the
+ * callback memory.
*
* @param port_id
* The port identifier of the Ethernet device.
*
* @return
* - 0: Success. Callback was removed.
+ * - -ENODEV: If *port_id* is invalid.
* - -ENOTSUP: Callback support is not available.
- * - -EINVAL: The port_id or the queue_id is out of range, or the callback
+ * - -EINVAL: The queue_id is out of range, or the callback
* is NULL or not found for the port/queue.
*/
int rte_eth_remove_tx_callback(uint16_t port_id, uint16_t queue_id,
*
* @return
* - 0: Success
+ * - -ENODEV: If *port_id* is invalid.
* - -ENOTSUP: routine is not supported by the device PMD.
- * - -EINVAL: The port_id or the queue_id is out of range.
+ * - -EINVAL: The queue_id is out of range, or the queue
+ * is hairpin queue.
*/
int rte_eth_rx_queue_info_get(uint16_t port_id, uint16_t queue_id,
struct rte_eth_rxq_info *qinfo);
*
* @return
* - 0: Success
+ * - -ENODEV: If *port_id* is invalid.
* - -ENOTSUP: routine is not supported by the device PMD.
- * - -EINVAL: The port_id or the queue_id is out of range.
+ * - -EINVAL: The queue_id is out of range, or the queue
+ * is hairpin queue.
*/
int rte_eth_tx_queue_info_get(uint16_t port_id, uint16_t queue_id,
struct rte_eth_txq_info *qinfo);
+/**
+ * Retrieve information about the Rx packet burst mode.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_id
+ * The Rx queue on the Ethernet device for which information
+ * will be retrieved.
+ * @param mode
+ * A pointer to a structure of type *rte_eth_burst_mode* to be filled
+ * with the information of the packet burst mode.
+ *
+ * @return
+ * - 0: Success
+ * - -ENODEV: If *port_id* is invalid.
+ * - -ENOTSUP: routine is not supported by the device PMD.
+ * - -EINVAL: The queue_id is out of range.
+ */
+__rte_experimental
+int rte_eth_rx_burst_mode_get(uint16_t port_id, uint16_t queue_id,
+ struct rte_eth_burst_mode *mode);
+
+/**
+ * Retrieve information about the Tx packet burst mode.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_id
+ * The Tx queue on the Ethernet device for which information
+ * will be retrieved.
+ * @param mode
+ * A pointer to a structure of type *rte_eth_burst_mode* to be filled
+ * with the information of the packet burst mode.
+ *
+ * @return
+ * - 0: Success
+ * - -ENODEV: If *port_id* is invalid.
+ * - -ENOTSUP: routine is not supported by the device PMD.
+ * - -EINVAL: The queue_id is out of range.
+ */
+__rte_experimental
+int rte_eth_tx_burst_mode_get(uint16_t port_id, uint16_t queue_id,
+ struct rte_eth_burst_mode *mode);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * Retrieve the monitor condition for a given receive queue.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_id
+ * The Rx queue on the Ethernet device for which information
+ * will be retrieved.
+ * @param pmc
+ * The pointer to power-optimized monitoring condition structure.
+ *
+ * @return
+ * - 0: Success.
+ * -ENOTSUP: Operation not supported.
+ * -EINVAL: Invalid parameters.
+ * -ENODEV: Invalid port ID.
+ */
+__rte_experimental
+int rte_eth_get_monitor_addr(uint16_t port_id, uint16_t queue_id,
+ struct rte_power_monitor_cond *pmc);
+
/**
* Retrieve device registers and register attributes (number of registers and
* register size)
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
* - (-ENODEV) if *port_id* invalid.
* - (-EIO) if device is removed.
* - others depends on the specific operations implementation.
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
* - (-ENODEV) if *port_id* invalid.
* - (-EIO) if device is removed.
* - others depends on the specific operations implementation.
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
* - (-EIO) if device is removed.
* - others depends on the specific operations implementation.
*/
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
* - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
* - (-EIO) if device is removed.
* - others depends on the specific operations implementation.
*/
-int __rte_experimental
+__rte_experimental
+int
rte_eth_dev_get_module_info(uint16_t port_id,
struct rte_eth_dev_module_info *modinfo);
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
* - (-ENODEV) if *port_id* invalid.
* - (-EIO) if device is removed.
* - others depends on the specific operations implementation.
*/
-int __rte_experimental
+__rte_experimental
+int
rte_eth_dev_get_module_eeprom(uint16_t port_id,
struct rte_dev_eeprom_info *info);
* - (-ENOSPC) if *port_id* has not enough multicast filtering resources.
*/
int rte_eth_dev_set_mc_addr_list(uint16_t port_id,
- struct ether_addr *mc_addr_set,
+ struct rte_ether_addr *mc_addr_set,
uint32_t nb_mc_addr);
/**
int rte_eth_timesync_write_time(uint16_t port_id, const struct timespec *time);
/**
- * Config l2 tunnel ether type of an Ethernet device for filtering specific
- * tunnel packets by ether type.
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
*
- * @param port_id
- * The port identifier of the Ethernet device.
- * @param l2_tunnel
- * l2 tunnel configuration.
+ * Read the current clock counter of an Ethernet device
*
- * @return
- * - (0) if successful.
- * - (-ENODEV) if port identifier is invalid.
- * - (-EIO) if device is removed.
- * - (-ENOTSUP) if hardware doesn't support tunnel type.
- */
-int
-rte_eth_dev_l2_tunnel_eth_type_conf(uint16_t port_id,
- struct rte_eth_l2_tunnel_conf *l2_tunnel);
-
-/**
- * Enable/disable l2 tunnel offload functions. Include,
- * 1, The ability of parsing a type of l2 tunnel of an Ethernet device.
- * Filtering, forwarding and offloading this type of tunnel packets depend on
- * this ability.
- * 2, Stripping the l2 tunnel tag.
- * 3, Insertion of the l2 tunnel tag.
- * 4, Forwarding the packets based on the l2 tunnel tag.
+ * This returns the current raw clock value of an Ethernet device. It is
+ * a raw amount of ticks, with no given time reference.
+ * The value returned here is from the same clock than the one
+ * filling timestamp field of Rx packets when using hardware timestamp
+ * offload. Therefore it can be used to compute a precise conversion of
+ * the device clock to the real time.
+ *
+ * E.g, a simple heuristic to derivate the frequency would be:
+ * uint64_t start, end;
+ * rte_eth_read_clock(port, start);
+ * rte_delay_ms(100);
+ * rte_eth_read_clock(port, end);
+ * double freq = (end - start) * 10;
+ *
+ * Compute a common reference with:
+ * uint64_t base_time_sec = current_time();
+ * uint64_t base_clock;
+ * rte_eth_read_clock(port, base_clock);
+ *
+ * Then, convert the raw mbuf timestamp with:
+ * base_time_sec + (double)(*timestamp_dynfield(mbuf) - base_clock) / freq;
+ *
+ * This simple example will not provide a very good accuracy. One must
+ * at least measure multiple times the frequency and do a regression.
+ * To avoid deviation from the system time, the common reference can
+ * be repeated from time to time. The integer division can also be
+ * converted by a multiplication and a shift for better performance.
*
* @param port_id
* The port identifier of the Ethernet device.
- * @param l2_tunnel
- * l2 tunnel parameters.
- * @param mask
- * Indicate the offload function.
- * @param en
- * Enable or disable this function.
+ * @param clock
+ * Pointer to the uint64_t that holds the raw clock value.
*
* @return
- * - (0) if successful.
- * - (-ENODEV) if port identifier is invalid.
- * - (-EIO) if device is removed.
- * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ * - 0: Success.
+ * - -ENODEV: The port ID is invalid.
+ * - -ENOTSUP: The function is not supported by the Ethernet driver.
*/
+__rte_experimental
int
-rte_eth_dev_l2_tunnel_offload_set(uint16_t port_id,
- struct rte_eth_l2_tunnel_conf *l2_tunnel,
- uint32_t mask,
- uint8_t en);
+rte_eth_read_clock(uint16_t port_id, uint64_t *clock);
/**
* Get the port id from device name. The device name should be specified
* Buffer of size RTE_ETH_NAME_MAX_LEN to store the name.
* @return
* - (0) if successful.
+* - (-ENODEV) if *port_id* is invalid.
* - (-EINVAL) on failure.
*/
int
void *
rte_eth_dev_get_sec_ctx(uint16_t port_id);
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change, or be removed, without prior notice
+ *
+ * Query the device hairpin capabilities.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param cap
+ * Pointer to a structure that will hold the hairpin capabilities.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ */
+__rte_experimental
+int rte_eth_dev_hairpin_capability_get(uint16_t port_id,
+ struct rte_eth_hairpin_cap *cap);
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice.
+ *
+ * ethernet device representor ID range entry
+ */
+struct rte_eth_representor_range {
+ enum rte_eth_representor_type type; /**< Representor type */
+ int controller; /**< Controller index */
+ int pf; /**< Physical function index */
+ __extension__
+ union {
+ int vf; /**< VF start index */
+ int sf; /**< SF start index */
+ };
+ uint32_t id_base; /**< Representor ID start index */
+ uint32_t id_end; /**< Representor ID end index */
+ char name[RTE_DEV_NAME_MAX_LEN]; /**< Representor name */
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice.
+ *
+ * Ethernet device representor information
+ */
+struct rte_eth_representor_info {
+ uint16_t controller; /**< Controller ID of caller device. */
+ uint16_t pf; /**< Physical function ID of caller device. */
+ struct rte_eth_representor_range ranges[];/**< Representor ID range. */
+};
+
+/**
+ * Retrieve the representor info of the device.
+ *
+ * Get device representor info to be able to calculate a unique
+ * representor ID. @see rte_eth_representor_id_get helper.
+ *
+ * @param port_id
+ * The port identifier of the device.
+ * @param info
+ * A pointer to a representor info structure.
+ * NULL to return number of range entries and allocate memory
+ * for next call to store detail.
+ * @return
+ * - (-ENOTSUP) if operation is not supported.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EIO) if device is removed.
+ * - (>=0) number of representor range entries supported by device.
+ */
+__rte_experimental
+int rte_eth_representor_info_get(uint16_t port_id,
+ struct rte_eth_representor_info *info);
#include <rte_ethdev_core.h>
* burst-oriented optimizations in both synchronous and asynchronous
* packet processing environments with no overhead in both cases.
*
+ * @note
+ * Some drivers using vector instructions require that *nb_pkts* is
+ * divisible by 4 or 8, depending on the driver implementation.
+ *
* The rte_eth_rx_burst() function does not provide any error
* notification to avoid the corresponding overhead. As a hint, the
* upper-level application might check the status of the device link once
* must be large enough to store *nb_pkts* pointers in it.
* @param nb_pkts
* The maximum number of packets to retrieve.
+ * The value must be divisible by 8 in order to work with any driver.
* @return
* The number of packets actually retrieved, which is the number
* of pointers to *rte_mbuf* structures effectively supplied to the
struct rte_eth_dev *dev = &rte_eth_devices[port_id];
uint16_t nb_rx;
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_RX
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, 0);
RTE_FUNC_PTR_OR_ERR_RET(*dev->rx_pkt_burst, 0);
rx_pkts, nb_pkts);
#ifdef RTE_ETHDEV_RXTX_CALLBACKS
- if (unlikely(dev->post_rx_burst_cbs[queue_id] != NULL)) {
- struct rte_eth_rxtx_callback *cb =
- dev->post_rx_burst_cbs[queue_id];
+ struct rte_eth_rxtx_callback *cb;
+
+ /* __ATOMIC_RELEASE memory order was used when the
+ * call back was inserted into the list.
+ * Since there is a clear dependency between loading
+ * cb and cb->fn/cb->next, __ATOMIC_ACQUIRE memory order is
+ * not required.
+ */
+ cb = __atomic_load_n(&dev->post_rx_burst_cbs[queue_id],
+ __ATOMIC_RELAXED);
+ if (unlikely(cb != NULL)) {
do {
nb_rx = cb->fn.rx(port_id, queue_id, rx_pkts, nb_rx,
nb_pkts, cb->param);
}
#endif
+ rte_ethdev_trace_rx_burst(port_id, queue_id, (void **)rx_pkts, nb_rx);
return nb_rx;
}
* The queue id on the specific port.
* @return
* The number of used descriptors in the specific queue, or:
- * (-EINVAL) if *port_id* or *queue_id* is invalid
+ * - (-ENODEV) if *port_id* is invalid.
+ * (-EINVAL) if *queue_id* is invalid
* (-ENOTSUP) if the device does not support this function
*/
static inline int
{
struct rte_eth_dev *dev;
- RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -EINVAL);
+ RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
dev = &rte_eth_devices[port_id];
- RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->rx_queue_count, -ENOTSUP);
- if (queue_id >= dev->data->nb_rx_queues)
+ RTE_FUNC_PTR_OR_ERR_RET(*dev->rx_queue_count, -ENOTSUP);
+ if (queue_id >= dev->data->nb_rx_queues ||
+ dev->data->rx_queues[queue_id] == NULL)
return -EINVAL;
- return (int)(*dev->dev_ops->rx_queue_count)(dev, queue_id);
+ return (int)(*dev->rx_queue_count)(dev, queue_id);
}
/**
* - (-ENODEV) if *port_id* invalid.
* - (-ENOTSUP) if the device does not support this function
*/
+__rte_deprecated
static inline int
rte_eth_rx_descriptor_done(uint16_t port_id, uint16_t queue_id, uint16_t offset)
{
struct rte_eth_dev *dev = &rte_eth_devices[port_id];
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
- RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->rx_descriptor_done, -ENOTSUP);
- return (*dev->dev_ops->rx_descriptor_done)( \
- dev->data->rx_queues[queue_id], offset);
+ RTE_FUNC_PTR_OR_ERR_RET(*dev->rx_descriptor_done, -ENOTSUP);
+ return (*dev->rx_descriptor_done)(dev->data->rx_queues[queue_id], offset);
}
#define RTE_ETH_RX_DESC_AVAIL 0 /**< Desc available for hw. */
struct rte_eth_dev *dev;
void *rxq;
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_RX
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
#endif
dev = &rte_eth_devices[port_id];
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_RX
if (queue_id >= dev->data->nb_rx_queues)
return -ENODEV;
#endif
- RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->rx_descriptor_status, -ENOTSUP);
+ RTE_FUNC_PTR_OR_ERR_RET(*dev->rx_descriptor_status, -ENOTSUP);
rxq = dev->data->rx_queues[queue_id];
- return (*dev->dev_ops->rx_descriptor_status)(rxq, offset);
+ return (*dev->rx_descriptor_status)(rxq, offset);
}
#define RTE_ETH_TX_DESC_FULL 0 /**< Desc filled for hw, waiting xmit. */
struct rte_eth_dev *dev;
void *txq;
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_TX
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -ENODEV);
#endif
dev = &rte_eth_devices[port_id];
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_TX
if (queue_id >= dev->data->nb_tx_queues)
return -ENODEV;
#endif
- RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->tx_descriptor_status, -ENOTSUP);
+ RTE_FUNC_PTR_OR_ERR_RET(*dev->tx_descriptor_status, -ENOTSUP);
txq = dev->data->tx_queues[queue_id];
- return (*dev->dev_ops->tx_descriptor_status)(txq, offset);
+ return (*dev->tx_descriptor_status)(txq, offset);
}
/**
{
struct rte_eth_dev *dev = &rte_eth_devices[port_id];
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_TX
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, 0);
RTE_FUNC_PTR_OR_ERR_RET(*dev->tx_pkt_burst, 0);
#endif
#ifdef RTE_ETHDEV_RXTX_CALLBACKS
- struct rte_eth_rxtx_callback *cb = dev->pre_tx_burst_cbs[queue_id];
+ struct rte_eth_rxtx_callback *cb;
+
+ /* __ATOMIC_RELEASE memory order was used when the
+ * call back was inserted into the list.
+ * Since there is a clear dependency between loading
+ * cb and cb->fn/cb->next, __ATOMIC_ACQUIRE memory order is
+ * not required.
+ */
+ cb = __atomic_load_n(&dev->pre_tx_burst_cbs[queue_id],
+ __ATOMIC_RELAXED);
if (unlikely(cb != NULL)) {
do {
}
#endif
+ rte_ethdev_trace_tx_burst(port_id, queue_id, (void **)tx_pkts,
+ nb_pkts);
return (*dev->tx_pkt_burst)(dev->data->tx_queues[queue_id], tx_pkts, nb_pkts);
}
* The number of packets correct and ready to be sent. The return value can be
* less than the value of the *tx_pkts* parameter when some packet doesn't
* meet devices requirements with rte_errno set appropriately:
- * - -EINVAL: offload flags are not correctly set
- * - -ENOTSUP: the offload feature is not supported by the hardware
+ * - EINVAL: offload flags are not correctly set
+ * - ENOTSUP: the offload feature is not supported by the hardware
+ * - ENODEV: if *port_id* is invalid (with debug enabled only)
*
*/
{
struct rte_eth_dev *dev;
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_TX
if (!rte_eth_dev_is_valid_port(port_id)) {
RTE_ETHDEV_LOG(ERR, "Invalid TX port_id=%u\n", port_id);
- rte_errno = EINVAL;
+ rte_errno = ENODEV;
return 0;
}
#endif
dev = &rte_eth_devices[port_id];
-#ifdef RTE_LIBRTE_ETHDEV_DEBUG
+#ifdef RTE_ETHDEV_DEBUG_TX
if (queue_id >= dev->data->nb_tx_queues) {
RTE_ETHDEV_LOG(ERR, "Invalid TX queue_id=%u\n", queue_id);
rte_errno = EINVAL;
git.droids-corp.org / dpdk.git / blobdiff