/**
* A structure used to retrieve link-level information of an Ethernet port.
*/
+__extension__
struct rte_eth_link {
uint32_t link_speed; /**< ETH_SPEED_NUM_ */
uint16_t link_duplex : 1; /**< ETH_LINK_[HALF/FULL]_DUPLEX */
enum rte_eth_rx_mq_mode mq_mode;
uint32_t max_rx_pkt_len; /**< Only used if jumbo_frame enabled. */
uint16_t split_hdr_size; /**< hdr buf size (header_split enabled).*/
+ __extension__
uint16_t header_split : 1, /**< Header Split enable. */
hw_ip_checksum : 1, /**< IP/UDP/TCP checksum offload enable. */
hw_vlan_filter : 1, /**< VLAN filter enable. */
/* For i40e specifically */
uint16_t pvid;
+ __extension__
uint8_t hw_vlan_reject_tagged : 1,
/**< If set, reject sending out tagged pkts */
hw_vlan_reject_untagged : 1,
const struct timespec *timestamp);
/**< @internal Function used to get time from the device clock */
-typedef int (*eth_get_reg_length_t)(struct rte_eth_dev *dev);
-/**< @internal Retrieve device register count */
-
typedef int (*eth_get_reg_t)(struct rte_eth_dev *dev,
struct rte_dev_reg_info *info);
/**< @internal Retrieve registers */
/** Query redirection table. */
reta_query_t reta_query;
- eth_get_reg_length_t get_reg_length;
- /**< Get # of registers */
eth_get_reg_t get_reg;
/**< Get registers */
eth_get_eeprom_length_t get_eeprom_length;
void *param;
};
-/**
- * The eth device type.
- */
-enum rte_eth_dev_type {
- RTE_ETH_DEV_UNKNOWN, /**< unknown device type */
- RTE_ETH_DEV_PCI,
- /**< Physical function and Virtual function of PCI devices */
- RTE_ETH_DEV_VIRTUAL, /**< non hardware device */
- RTE_ETH_DEV_MAX /**< max value of this enum */
-};
-
/**
* @internal
* The generic data structure associated with each ethernet device.
*/
struct rte_eth_rxtx_callback *pre_tx_burst_cbs[RTE_MAX_QUEUES_PER_PORT];
uint8_t attached; /**< Flag indicating the port is attached */
- enum rte_eth_dev_type dev_type; /**< Flag indicating the device type */
} __rte_cache_aligned;
struct rte_eth_dev_sriov {
struct ether_addr* hash_mac_addrs;
/** Device Ethernet MAC addresses of hash filtering. */
uint8_t port_id; /**< Device [external] port identifier. */
+ __extension__
uint8_t promiscuous : 1, /**< RX promiscuous mode ON(1) / OFF(0). */
scattered_rx : 1, /**< RX of scattered packets is ON(1) / OFF(0) */
all_multicast : 1, /**< RX all multicast mode ON(1) / OFF(0). */
* @return
* - Slot in the rte_dev_devices array for a new device;
*/
-struct rte_eth_dev *rte_eth_dev_allocate(const char *name,
- enum rte_eth_dev_type type);
+struct rte_eth_dev *rte_eth_dev_allocate(const char *name);
/**
* @internal
unsigned int dev_private_size; /**< Size of device private data. */
};
-/**
- * @internal
- * A function invoked by the initialization function of an Ethernet driver
- * to simultaneously register itself as a PCI driver and as an Ethernet
- * Poll Mode Driver (PMD).
- *
- * @param eth_drv
- * The pointer to the *eth_driver* structure associated with
- * the Ethernet driver.
- */
-void rte_eth_driver_register(struct eth_driver *eth_drv);
-
/**
* Convert a numerical speed in Mbps to a bitmap flag that can be used in
* the bitmap link_speeds of the struct rte_eth_conf
int rte_eth_dev_is_valid_port(uint8_t port_id);
/**
- * Allocate mbuf from mempool, setup the DMA physical address
- * and then start RX for specified queue of a port. It is used
- * when rx_deferred_start flag of the specified queue is true.
+ * Start specified RX queue of a port. It is used when rx_deferred_start
+ * flag of the specified queue is true.
*
* @param port_id
* The port identifier of the Ethernet device
* The value must be in the range [0, nb_rx_queue - 1] previously supplied
* to rte_eth_dev_configure().
* @return
- * - 0: Success, the transmit queue is correctly set up.
+ * - 0: Success, the receive queue is started.
* - -EINVAL: The port_id or the queue_id out of range.
* - -ENOTSUP: The function not supported in PMD driver.
*/
* The value must be in the range [0, nb_rx_queue - 1] previously supplied
* to rte_eth_dev_configure().
* @return
- * - 0: Success, the transmit queue is correctly set up.
+ * - 0: Success, the receive queue is stopped.
* - -EINVAL: The port_id or the queue_id out of range.
* - -ENOTSUP: The function not supported in PMD driver.
*/
* The value must be in the range [0, nb_tx_queue - 1] previously supplied
* to rte_eth_dev_configure().
* @return
- * - 0: Success, the transmit queue is correctly set up.
+ * - 0: Success, the transmit queue is started.
* - -EINVAL: The port_id or the queue_id out of range.
* - -ENOTSUP: The function not supported in PMD driver.
*/
* The value must be in the range [0, nb_tx_queue - 1] previously supplied
* to rte_eth_dev_configure().
* @return
- * - 0: Success, the transmit queue is correctly set up.
+ * - 0: Success, the transmit queue is stopped.
* - -EINVAL: The port_id or the queue_id out of range.
* - -ENOTSUP: The function not supported in PMD driver.
*/
/**
* Retrieve the supported packet types of an Ethernet device.
*
+ * When a packet type is announced as supported, it *must* be recognized by
+ * the PMD. For instance, if RTE_PTYPE_L2_ETHER, RTE_PTYPE_L2_ETHER_VLAN
+ * and RTE_PTYPE_L3_IPV4 are announced, the PMD must return the following
+ * packet types for these packets:
+ * - Ether/IPv4 -> RTE_PTYPE_L2_ETHER | RTE_PTYPE_L3_IPV4
+ * - Ether/Vlan/IPv4 -> RTE_PTYPE_L2_ETHER_VLAN | RTE_PTYPE_L3_IPV4
+ * - Ether/[anything else] -> RTE_PTYPE_L2_ETHER
+ * - Ether/Vlan/[anything else] -> RTE_PTYPE_L2_ETHER_VLAN
+ *
+ * When a packet is received by a PMD, the most precise type must be
+ * returned among the ones supported. However a PMD is allowed to set
+ * packet type that is not in the supported list, at the condition that it
+ * is more precise. Therefore, a PMD announcing no supported packet types
+ * can still set a matching packet type in a received packet.
+ *
* @note
* Better to invoke this API after the device is already started or rx burst
* function is decided, to obtain correct supported ptypes.
struct rte_eth_txq_info *qinfo);
/**
- * Retrieve number of available registers for access
- *
- * @param port_id
- * The port identifier of the Ethernet device.
- * @return
- * - (>=0) number of registers if successful.
- * - (-ENOTSUP) if hardware doesn't support.
- * - (-ENODEV) if *port_id* invalid.
- * - others depends on the specific operations implementation.
- */
-int rte_eth_dev_get_reg_length(uint8_t port_id);
-
-/**
- * Retrieve device registers and register attributes
+ * Retrieve device registers and register attributes (number of registers and
+ * register size)
*
* @param port_id
* The port identifier of the Ethernet device.
* @param info
- * The template includes buffer for register data and attribute to be filled.
+ * Pointer to rte_dev_reg_info structure to fill in. If info->data is
+ * NULL the function fills in the width and length fields. If non-NULL
+ * the registers are put into the buffer pointed at by the data field.
* @return
* - (0) if successful.
* - (-ENOTSUP) if hardware doesn't support.
int
rte_eth_dev_get_name_by_port(uint8_t port_id, char *name);
+/**
+ * @internal
+ * Wrapper for use by pci drivers as a .probe function to attach to a ethdev
+ * interface.
+ */
+int rte_eth_dev_pci_probe(struct rte_pci_driver *pci_drv,
+ struct rte_pci_device *pci_dev);
+
+/**
+ * @internal
+ * Wrapper for use by pci drivers as a .remove function to detach a ethdev
+ * interface.
+ */
+int rte_eth_dev_pci_remove(struct rte_pci_device *pci_dev);
+
#ifdef __cplusplus
}
#endif
git.droids-corp.org / dpdk.git / blobdiff