/**< Total of RX packets dropped by the HW,
* because there are no available mbufs (i.e. RX queues are full).
*/
- uint64_t ibadcrc __rte_deprecated;
- /**< Deprecated; Total of RX packets with CRC error. */
- uint64_t ibadlen __rte_deprecated;
- /**< Deprecated; Total of RX packets with bad length. */
uint64_t ierrors; /**< Total number of erroneous received packets. */
uint64_t oerrors; /**< Total number of failed transmitted packets. */
- uint64_t imcasts;
- /**< Deprecated; Total number of multicast received packets. */
uint64_t rx_nombuf; /**< Total number of RX mbuf allocation failures. */
- uint64_t fdirmatch __rte_deprecated;
- /**< Deprecated; Total number of RX packets matching a filter. */
- uint64_t fdirmiss __rte_deprecated;
- /**< Deprecated; Total number of RX packets not matching any filter. */
- uint64_t tx_pause_xon __rte_deprecated;
- /**< Deprecated; Total nb. of XON pause frame sent. */
- uint64_t rx_pause_xon __rte_deprecated;
- /**< Deprecated; Total nb. of XON pause frame received. */
- uint64_t tx_pause_xoff __rte_deprecated;
- /**< Deprecated; Total nb. of XOFF pause frame sent. */
- uint64_t rx_pause_xoff __rte_deprecated;
- /**< Deprecated; Total nb. of XOFF pause frame received. */
uint64_t q_ipackets[RTE_ETHDEV_QUEUE_STAT_CNTRS];
/**< Total number of queue RX packets. */
uint64_t q_opackets[RTE_ETHDEV_QUEUE_STAT_CNTRS];
/**< Total number of successfully transmitted queue bytes. */
uint64_t q_errors[RTE_ETHDEV_QUEUE_STAT_CNTRS];
/**< Total number of queue packets received that are dropped. */
- uint64_t ilbpackets;
- /**< Total number of good packets received from loopback,VF Only */
- uint64_t olbpackets;
- /**< Total number of good packets transmitted to loopback,VF Only */
- uint64_t ilbbytes;
- /**< Total number of good bytes received from loopback,VF Only */
- uint64_t olbbytes;
- /**< Total number of good bytes transmitted to loopback,VF Only */
};
+/**
+ * Device supported speeds bitmap flags
+ */
+#define ETH_LINK_SPEED_AUTONEG (0 << 0) /**< Autonegotiate (all speeds) */
+#define ETH_LINK_SPEED_FIXED (1 << 0) /**< Disable autoneg (fixed speed) */
+#define ETH_LINK_SPEED_10M_HD (1 << 1) /**< 10 Mbps half-duplex */
+#define ETH_LINK_SPEED_10M (1 << 2) /**< 10 Mbps full-duplex */
+#define ETH_LINK_SPEED_100M_HD (1 << 3) /**< 100 Mbps half-duplex */
+#define ETH_LINK_SPEED_100M (1 << 4) /**< 100 Mbps full-duplex */
+#define ETH_LINK_SPEED_1G (1 << 5) /**< 1 Gbps */
+#define ETH_LINK_SPEED_2_5G (1 << 6) /**< 2.5 Gbps */
+#define ETH_LINK_SPEED_5G (1 << 7) /**< 5 Gbps */
+#define ETH_LINK_SPEED_10G (1 << 8) /**< 10 Gbps */
+#define ETH_LINK_SPEED_20G (1 << 9) /**< 20 Gbps */
+#define ETH_LINK_SPEED_25G (1 << 10) /**< 25 Gbps */
+#define ETH_LINK_SPEED_40G (1 << 11) /**< 40 Gbps */
+#define ETH_LINK_SPEED_50G (1 << 12) /**< 50 Gbps */
+#define ETH_LINK_SPEED_56G (1 << 13) /**< 56 Gbps */
+#define ETH_LINK_SPEED_100G (1 << 14) /**< 100 Gbps */
+
+/**
+ * Ethernet numeric link speeds in Mbps
+ */
+#define ETH_SPEED_NUM_NONE 0 /**< Not defined */
+#define ETH_SPEED_NUM_10M 10 /**< 10 Mbps */
+#define ETH_SPEED_NUM_100M 100 /**< 100 Mbps */
+#define ETH_SPEED_NUM_1G 1000 /**< 1 Gbps */
+#define ETH_SPEED_NUM_2_5G 2500 /**< 2.5 Gbps */
+#define ETH_SPEED_NUM_5G 5000 /**< 5 Gbps */
+#define ETH_SPEED_NUM_10G 10000 /**< 10 Gbps */
+#define ETH_SPEED_NUM_20G 20000 /**< 20 Gbps */
+#define ETH_SPEED_NUM_25G 25000 /**< 25 Gbps */
+#define ETH_SPEED_NUM_40G 40000 /**< 40 Gbps */
+#define ETH_SPEED_NUM_50G 50000 /**< 50 Gbps */
+#define ETH_SPEED_NUM_56G 56000 /**< 56 Gbps */
+#define ETH_SPEED_NUM_100G 100000 /**< 100 Gbps */
+
/**
* A structure used to retrieve link-level information of an Ethernet port.
*/
struct rte_eth_link {
- uint16_t link_speed; /**< ETH_LINK_SPEED_[10, 100, 1000, 10000] */
- uint16_t link_duplex; /**< ETH_LINK_[HALF_DUPLEX, FULL_DUPLEX] */
- uint8_t link_status : 1; /**< 1 -> link up, 0 -> link down */
-}__attribute__((aligned(8))); /**< aligned for atomic64 read/write */
-
-#define ETH_LINK_SPEED_AUTONEG 0 /**< Auto-negotiate link speed. */
-#define ETH_LINK_SPEED_10 10 /**< 10 megabits/second. */
-#define ETH_LINK_SPEED_100 100 /**< 100 megabits/second. */
-#define ETH_LINK_SPEED_1000 1000 /**< 1 gigabits/second. */
-#define ETH_LINK_SPEED_10000 10000 /**< 10 gigabits/second. */
-#define ETH_LINK_SPEED_10G 10000 /**< alias of 10 gigabits/second. */
-#define ETH_LINK_SPEED_20G 20000 /**< 20 gigabits/second. */
-#define ETH_LINK_SPEED_40G 40000 /**< 40 gigabits/second. */
+ uint32_t link_speed; /**< ETH_SPEED_NUM_ */
+ uint16_t link_duplex : 1; /**< ETH_LINK_[HALF/FULL]_DUPLEX */
+ uint16_t link_autoneg : 1; /**< ETH_LINK_SPEED_[AUTONEG/FIXED] */
+ uint16_t link_status : 1; /**< ETH_LINK_[DOWN/UP] */
+} __attribute__((aligned(8))); /**< aligned for atomic64 read/write */
-#define ETH_LINK_AUTONEG_DUPLEX 0 /**< Auto-negotiate duplex. */
-#define ETH_LINK_HALF_DUPLEX 1 /**< Half-duplex connection. */
-#define ETH_LINK_FULL_DUPLEX 2 /**< Full-duplex connection. */
+/* Utility constants */
+#define ETH_LINK_HALF_DUPLEX 0 /**< Half-duplex connection. */
+#define ETH_LINK_FULL_DUPLEX 1 /**< Full-duplex connection. */
+#define ETH_LINK_DOWN 0 /**< Link is down. */
+#define ETH_LINK_UP 1 /**< Link is up. */
+#define ETH_LINK_FIXED 0 /**< No autonegotiation. */
+#define ETH_LINK_AUTONEG 1 /**< Autonegotiated. */
/**
* A structure used to configure the ring threshold registers of an RX/TX
enable_lro : 1; /**< Enable LRO */
};
+/**
+ * VLAN types to indicate if it is for single VLAN, inner VLAN or outer VLAN.
+ * Note that single VLAN is treated the same as inner VLAN.
+ */
+enum rte_vlan_type {
+ ETH_VLAN_TYPE_UNKNOWN = 0,
+ ETH_VLAN_TYPE_INNER, /**< Single VLAN, or inner VLAN. */
+ ETH_VLAN_TYPE_OUTER, /**< Outer VLAN. */
+ ETH_VLAN_TYPE_MAX,
+};
+
/**
* A structure used to configure the Receive Side Scaling (RSS) feature
* of an Ethernet port.
/**
* UDP tunneling configuration.
+ * Used to config the UDP port for a type of tunnel.
+ * NICs need the UDP port to identify the tunnel type.
+ * Normally a type of tunnel has a default UDP port, this structure can be used
+ * in case if the users want to change or support more UDP port.
*/
struct rte_eth_udp_tunnel {
- uint16_t udp_port;
- uint8_t prot_type;
+ uint16_t udp_port; /**< UDP port used for the tunnel. */
+ uint8_t prot_type; /**< Tunnel type. Defined in rte_eth_tunnel_type. */
};
/**
* configuration settings may be needed.
*/
struct rte_eth_conf {
- uint16_t link_speed;
- /**< ETH_LINK_SPEED_10[0|00|000], or 0 for autonegotation */
- uint16_t link_duplex;
- /**< ETH_LINK_[HALF_DUPLEX|FULL_DUPLEX], or 0 for autonegotation */
+ uint32_t link_speeds; /**< bitmap of ETH_LINK_SPEED_XXX of speeds to be
+ used. ETH_LINK_SPEED_FIXED disables link
+ autonegotiation, and a unique speed shall be
+ set. Otherwise, the bitmap defines the set of
+ speeds to be advertised. If the special value
+ ETH_LINK_SPEED_AUTONEG (0) is used, all speeds
+ supported are advertised. */
struct rte_eth_rxmode rxmode; /**< Port RX configuration. */
struct rte_eth_txmode txmode; /**< Port TX configuration. */
uint32_t lpbk_mode; /**< Loopback operation mode. By default the value
#define DEV_RX_OFFLOAD_TCP_CKSUM 0x00000008
#define DEV_RX_OFFLOAD_TCP_LRO 0x00000010
#define DEV_RX_OFFLOAD_QINQ_STRIP 0x00000020
+#define DEV_RX_OFFLOAD_OUTER_IPV4_CKSUM 0x00000040
/**
* TX offload capabilities of a device.
#define DEV_TX_OFFLOAD_OUTER_IPV4_CKSUM 0x00000080 /**< Used for tunneling packet. */
#define DEV_TX_OFFLOAD_QINQ_INSERT 0x00000100
+/**
+ * Ethernet device information
+ */
struct rte_eth_dev_info {
struct rte_pci_device *pci_dev; /**< Device PCI information. */
const char *driver_name; /**< Device Driver name. */
uint16_t vmdq_pool_base; /**< First ID of VMDQ pools. */
struct rte_eth_desc_lim rx_desc_lim; /**< RX descriptors limits */
struct rte_eth_desc_lim tx_desc_lim; /**< TX descriptors limits */
+ uint32_t speed_capa; /**< Supported speeds bitmap (ETH_LINK_SPEED_). */
};
/**
* statistics that are not provided in the generic rte_eth_stats
* structure.
*/
-struct rte_eth_xstats {
- char name[RTE_ETH_XSTATS_NAME_SIZE];
+struct rte_eth_xstat {
+ uint64_t id;
uint64_t value;
};
+/**
+ * A name-key lookup element for extended statistics.
+ *
+ * This structure is used to map between names and ID numbers
+ * for extended ethernet statistics.
+ */
+struct rte_eth_xstat_name {
+ char name[RTE_ETH_XSTATS_NAME_SIZE];
+ uint64_t id;
+};
+
#define ETH_DCB_NUM_TCS 8
#define ETH_MAX_VMDQ_POOL 64
} \
} while (0)
+/**
+ * l2 tunnel configuration.
+ */
+
+/**< l2 tunnel enable mask */
+#define ETH_L2_TUNNEL_ENABLE_MASK 0x00000001
+/**< l2 tunnel insertion mask */
+#define ETH_L2_TUNNEL_INSERTION_MASK 0x00000002
+/**< l2 tunnel stripping mask */
+#define ETH_L2_TUNNEL_STRIPPING_MASK 0x00000004
+/**< l2 tunnel forwarding mask */
+#define ETH_L2_TUNNEL_FORWARDING_MASK 0x00000008
+
/*
* Definitions of all functions exported by an Ethernet driver through the
* the generic structure of type *eth_dev_ops* supplied in the *rte_eth_dev*
/**< @internal Reset global I/O statistics of an Ethernet device to 0. */
typedef int (*eth_xstats_get_t)(struct rte_eth_dev *dev,
- struct rte_eth_xstats *stats, unsigned n);
+ struct rte_eth_xstat *stats, unsigned n);
/**< @internal Get extended stats of an Ethernet device. */
typedef void (*eth_xstats_reset_t)(struct rte_eth_dev *dev);
/**< @internal Reset extended stats of an Ethernet device. */
+typedef int (*eth_xstats_get_names_t)(struct rte_eth_dev *dev,
+ struct rte_eth_xstat_name *xstats_names, unsigned size);
+/**< @internal Get names of extended stats of an Ethernet device. */
+
typedef int (*eth_queue_stats_mapping_set_t)(struct rte_eth_dev *dev,
uint16_t queue_id,
uint8_t stat_idx,
struct rte_eth_dev_info *dev_info);
/**< @internal Get specific informations of an Ethernet device. */
+typedef const uint32_t *(*eth_dev_supported_ptypes_get_t)(struct rte_eth_dev *dev);
+/**< @internal Get supported ptypes of an Ethernet device. */
+
typedef int (*eth_queue_start_t)(struct rte_eth_dev *dev,
uint16_t queue_id);
/**< @internal Start rx and tx of a queue of an Ethernet device. */
int on);
/**< @internal filtering of a VLAN Tag Identifier by an Ethernet device. */
-typedef void (*vlan_tpid_set_t)(struct rte_eth_dev *dev,
- uint16_t tpid);
+typedef int (*vlan_tpid_set_t)(struct rte_eth_dev *dev,
+ enum rte_vlan_type type, uint16_t tpid);
/**< @internal set the outer VLAN-TPID by an Ethernet device. */
typedef void (*vlan_offload_set_t)(struct rte_eth_dev *dev, int mask);
uint8_t rule_id);
/**< @internal Remove a traffic mirroring rule on an Ethernet device */
-typedef int (*eth_udp_tunnel_add_t)(struct rte_eth_dev *dev,
- struct rte_eth_udp_tunnel *tunnel_udp);
-/**< @internal Add tunneling UDP info */
+typedef int (*eth_udp_tunnel_port_add_t)(struct rte_eth_dev *dev,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+/**< @internal Add tunneling UDP port */
-typedef int (*eth_udp_tunnel_del_t)(struct rte_eth_dev *dev,
- struct rte_eth_udp_tunnel *tunnel_udp);
-/**< @internal Delete tunneling UDP info */
+typedef int (*eth_udp_tunnel_port_del_t)(struct rte_eth_dev *dev,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+/**< @internal Delete tunneling UDP port */
typedef int (*eth_set_mc_addr_list_t)(struct rte_eth_dev *dev,
struct ether_addr *mc_addr_set,
struct rte_dev_eeprom_info *info);
/**< @internal Program eeprom data */
+typedef int (*eth_l2_tunnel_eth_type_conf_t)
+ (struct rte_eth_dev *dev, struct rte_eth_l2_tunnel_conf *l2_tunnel);
+/**< @internal config l2 tunnel ether type */
+
+typedef int (*eth_l2_tunnel_offload_set_t)
+ (struct rte_eth_dev *dev,
+ struct rte_eth_l2_tunnel_conf *l2_tunnel,
+ uint32_t mask,
+ uint8_t en);
+/**< @internal enable/disable the l2 tunnel offload functions */
+
#ifdef RTE_NIC_BYPASS
enum {
eth_stats_reset_t stats_reset; /**< Reset generic device statistics. */
eth_xstats_get_t xstats_get; /**< Get extended device statistics. */
eth_xstats_reset_t xstats_reset; /**< Reset extended device statistics. */
+ eth_xstats_get_names_t xstats_get_names;
+ /**< Get names of extended statistics. */
eth_queue_stats_mapping_set_t queue_stats_mapping_set;
/**< Configure per queue stat counter mapping. */
eth_dev_infos_get_t dev_infos_get; /**< Get device info. */
+ eth_dev_supported_ptypes_get_t dev_supported_ptypes_get;
+ /**< Get packet types supported and identified by device*/
mtu_set_t mtu_set; /**< Set MTU. */
vlan_filter_set_t vlan_filter_set; /**< Filter VLAN Setup. */
vlan_tpid_set_t vlan_tpid_set; /**< Outer VLAN TPID Setup. */
eth_set_vf_rx_t set_vf_rx; /**< enable/disable a VF receive */
eth_set_vf_tx_t set_vf_tx; /**< enable/disable a VF transmit */
eth_set_vf_vlan_filter_t set_vf_vlan_filter; /**< Set VF VLAN filter */
- eth_udp_tunnel_add_t udp_tunnel_add;
- eth_udp_tunnel_del_t udp_tunnel_del;
+ /** Add UDP tunnel port. */
+ eth_udp_tunnel_port_add_t udp_tunnel_port_add;
+ /** Del UDP tunnel port. */
+ eth_udp_tunnel_port_del_t udp_tunnel_port_del;
eth_set_queue_rate_limit_t set_queue_rate_limit; /**< Set queue rate limit */
eth_set_vf_rate_limit_t set_vf_rate_limit; /**< Set VF rate limit */
/** Update redirection table. */
eth_timesync_read_time timesync_read_time;
/** Set the device clock time. */
eth_timesync_write_time timesync_write_time;
+ /** Config ether type of l2 tunnel */
+ eth_l2_tunnel_eth_type_conf_t l2_tunnel_eth_type_conf;
+ /** Enable/disable l2 tunnel offload functions */
+ eth_l2_tunnel_offload_set_t l2_tunnel_offload_set;
};
/**
#define RTE_ETH_DEV_DETACHABLE 0x0001
/** Device supports link state interrupt */
#define RTE_ETH_DEV_INTR_LSC 0x0002
+/** Device is a bonded slave */
+#define RTE_ETH_DEV_BONDED_SLAVE 0x0004
/**
* @internal
*/
void rte_eth_driver_register(struct eth_driver *eth_drv);
+/**
+ * Convert a numerical speed in Mbps to a bitmap flag that can be used in
+ * the bitmap link_speeds of the struct rte_eth_conf
+ *
+ * @param speed
+ * Numerical speed value in Mbps
+ * @param duplex
+ * ETH_LINK_[HALF/FULL]_DUPLEX (only for 10/100M speeds)
+ * @return
+ * 0 if the speed cannot be mapped
+ */
+uint32_t rte_eth_speed_bitflag(uint32_t speed, int duplex);
+
/**
* Configure an Ethernet device.
* This function must be invoked first before any other function in the
*/
void rte_eth_stats_reset(uint8_t port_id);
+/**
+ * Retrieve names of extended statistics of an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param xstats_names
+ * Block of memory to insert names into. Must be at least size in capacity.
+ * If set to NULL, function returns required capacity.
+ * @param size
+ * Capacity of xstats_names (number of names).
+ * @return
+ * - positive value lower or equal to size: success. The return value
+ * is the number of entries filled in the stats table.
+ * - positive value higher than size: error, the given statistics table
+ * is too small. The return value corresponds to the size that should
+ * be given to succeed. The entries in the table are not valid and
+ * shall not be used by the caller.
+ * - negative value on error (invalid port id)
+ */
+int rte_eth_xstats_get_names(uint8_t port_id,
+ struct rte_eth_xstat_name *xstats_names,
+ unsigned size);
+
/**
* Retrieve extended statistics of an Ethernet device.
*
* shall not be used by the caller.
* - negative value on error (invalid port id)
*/
-int rte_eth_xstats_get(uint8_t port_id, struct rte_eth_xstats *xstats,
+int rte_eth_xstats_get(uint8_t port_id, struct rte_eth_xstat *xstats,
unsigned n);
/**
*/
void rte_eth_dev_info_get(uint8_t port_id, struct rte_eth_dev_info *dev_info);
+/**
+ * Retrieve the supported packet types of an Ethernet device.
+ *
+ * @note
+ * Better to invoke this API after the device is already started or rx burst
+ * function is decided, to obtain correct supported ptypes.
+ * @note
+ * if a given PMD does not report what ptypes it supports, then the supported
+ * ptype count is reported as 0.
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param ptype_mask
+ * A hint of what kind of packet type which the caller is interested in.
+ * @param ptypes
+ * An array pointer to store adequent packet types, allocated by caller.
+ * @param num
+ * Size of the array pointed by param ptypes.
+ * @return
+ * - (>=0) Number of supported ptypes. If the number of types exceeds num,
+ * only num entries will be filled into the ptypes array, but the full
+ * count of supported ptypes will be returned.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+int rte_eth_dev_get_supported_ptypes(uint8_t port_id, uint32_t ptype_mask,
+ uint32_t *ptypes, int num);
+
/**
* Retrieve the MTU of an Ethernet device.
*
*
* @param port_id
* The port identifier of the Ethernet device.
+ * @param vlan_type
+ * The vlan type.
* @param tag_type
* The Tag Protocol ID
* @return
* - (-ENOSUP) if hardware-assisted VLAN TPID setup is not supported.
* - (-ENODEV) if *port_id* invalid.
*/
-int rte_eth_dev_set_vlan_ether_type(uint8_t port_id, uint16_t tag_type);
+int rte_eth_dev_set_vlan_ether_type(uint8_t port_id,
+ enum rte_vlan_type vlan_type,
+ uint16_t tag_type);
/**
* Set VLAN offload configuration on an Ethernet device
* on the output queue *queue_id* of the Ethernet device designated by its
* *port_id*.
* The *nb_pkts* parameter is the number of packets to send which are
- * supplied in the *tx_pkts* array of *rte_mbuf* structures.
+ * supplied in the *tx_pkts* array of *rte_mbuf* structures, each of them
+ * allocated from a pool created with rte_pktmbuf_pool_create().
* The rte_eth_tx_burst() function loops, sending *nb_pkts* packets,
* up to the number of transmit descriptors available in the TX ring of the
* transmit queue.
enum rte_eth_event_type {
RTE_ETH_EVENT_UNKNOWN, /**< unknown event type */
RTE_ETH_EVENT_INTR_LSC, /**< lsc interrupt event */
+ RTE_ETH_EVENT_QUEUE_STATE,
+ /**< queue state event (enabled/disabled) */
+ RTE_ETH_EVENT_INTR_RESET,
+ /**< reset interrupt event, sent to VF on PF reset */
RTE_ETH_EVENT_MAX /**< max value of this enum */
};
struct rte_eth_rss_conf *rss_conf);
/**
- * Add UDP tunneling port of an Ethernet device for filtering a specific
- * tunneling packet by UDP port number.
+ * Add UDP tunneling port for a specific type of tunnel.
+ * The packets with this UDP port will be identified as this type of tunnel.
+ * Before enabling any offloading function for a tunnel, users can call this API
+ * to change or add more UDP port for the tunnel. So the offloading function
+ * can take effect on the packets with the sepcific UDP port.
*
* @param port_id
* The port identifier of the Ethernet device.
* - (-ENOTSUP) if hardware doesn't support tunnel type.
*/
int
-rte_eth_dev_udp_tunnel_add(uint8_t port_id,
- struct rte_eth_udp_tunnel *tunnel_udp);
+rte_eth_dev_udp_tunnel_port_add(uint8_t port_id,
+ struct rte_eth_udp_tunnel *tunnel_udp);
/**
- * Detete UDP tunneling port configuration of Ethernet device
+ * Delete UDP tunneling port a specific type of tunnel.
+ * The packets with this UDP port will not be identified as this type of tunnel
+ * any more.
+ * Before enabling any offloading function for a tunnel, users can call this API
+ * to delete a UDP port for the tunnel. So the offloading function will not take
+ * effect on the packets with the sepcific UDP port.
*
* @param port_id
* The port identifier of the Ethernet device.
* - (-ENOTSUP) if hardware doesn't support tunnel type.
*/
int
-rte_eth_dev_udp_tunnel_delete(uint8_t port_id,
- struct rte_eth_udp_tunnel *tunnel_udp);
+rte_eth_dev_udp_tunnel_port_delete(uint8_t port_id,
+ struct rte_eth_udp_tunnel *tunnel_udp);
/**
* Check whether the filter type is supported on an Ethernet device.
void *rte_eth_add_rx_callback(uint8_t port_id, uint16_t queue_id,
rte_rx_callback_fn fn, void *user_param);
+/*
+* Add a callback that must be called first on packet RX on a given port
+* and queue.
+*
+* This API configures a first function to be called for each burst of
+* packets received on a given NIC port queue. The return value is a pointer
+* that can be used to later remove the callback using
+* rte_eth_remove_rx_callback().
+*
+* Multiple functions are called in the order that they are added.
+*
+* @param port_id
+* The port identifier of the Ethernet device.
+* @param queue_id
+* The queue on the Ethernet device on which the callback is to be added.
+* @param fn
+* The callback function
+* @param user_param
+* A generic pointer parameter which will be passed to each invocation of the
+* callback function on this port and queue.
+*
+* @return
+* NULL on error.
+* On success, a pointer value which can later be used to remove the callback.
+*/
+void *rte_eth_add_first_rx_callback(uint8_t port_id, uint16_t queue_id,
+ rte_rx_callback_fn fn, void *user_param);
+
/**
* Add a callback to be called on packet TX on a given port and queue.
*
uint16_t queue_id, size_t size,
unsigned align, int socket_id);
+/**
+ * Config l2 tunnel ether type of an Ethernet device for filtering specific
+ * tunnel packets by ether type.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param l2_tunnel
+ * l2 tunnel configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ */
+int
+rte_eth_dev_l2_tunnel_eth_type_conf(uint8_t port_id,
+ struct rte_eth_l2_tunnel_conf *l2_tunnel);
+
+/**
+ * Enable/disable l2 tunnel offload functions. Include,
+ * 1, The ability of parsing a type of l2 tunnel of an Ethernet device.
+ * Filtering, forwarding and offloading this type of tunnel packets depend on
+ * this ability.
+ * 2, Stripping the l2 tunnel tag.
+ * 3, Insertion of the l2 tunnel tag.
+ * 4, Forwarding the packets based on the l2 tunnel tag.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param l2_tunnel
+ * l2 tunnel parameters.
+ * @param mask
+ * Indicate the offload function.
+ * @param en
+ * Enable or disable this function.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ */
+int
+rte_eth_dev_l2_tunnel_offload_set(uint8_t port_id,
+ struct rte_eth_l2_tunnel_conf *l2_tunnel,
+ uint32_t mask,
+ uint8_t en);
+
#ifdef __cplusplus
}
#endif
git.droids-corp.org / dpdk.git / blobdiff