unify tools naming

[dpdk.git] / doc / guides / nics / bnx2x.rst

diff --git a/doc/guides/nics/bnx2x.rst b/doc/guides/nics/bnx2x.rst
index 7a94080..6453168 100644 (file)
--- a/doc/guides/nics/bnx2x.rst
+++ b/doc/guides/nics/bnx2x.rst
@@ -60,6 +60,7 @@ The features not yet supported include:
 - LRO/TSO offload
 - Checksum offload
 - SR-IOV PF
+- Rx TX scatter gather
 
 Co-existence considerations
 ---------------------------
@@ -81,7 +82,7 @@ Supported QLogic NICs
 Prerequisites
 -------------
 
-- Requires firmware version **7.2.51.0**. It is inbox on most of the
+- Requires firmware version **7.2.51.0**. It is included in most of the
   standard Linux distros. If it is not available visit
   `QLogic Driver Download Center <http://driverdownloads.qlogic.com>`_
   to get the required firmware.
@@ -143,6 +144,14 @@ command::
    cd <DPDK-source-directory>
    make config T=i686-native-linuxapp-gcc install
 
+To compile BNX2X PMD for Linux i686 gcc target, run the following "make"
+command:
+
+.. code-block:: console
+
+   cd <DPDK-source-directory>
+   make config T=i686-native-linuxapp-gcc install
+
 To compile BNX2X PMD for FreeBSD x86_64 clang target, run the following "gmake"
 command::
 
@@ -155,6 +164,14 @@ command::
    cd <DPDK-source-directory>
    gmake config T=x86_64-native-bsdapp-gcc install -Wl,-rpath=/usr/local/lib/gcc48 CC=gcc48
 
+To compile BNX2X PMD for FreeBSD x86_64 gcc target, run the following "gmake"
+command:
+
+.. code-block:: console
+
+   cd <DPDK-source-directory>
+   gmake config T=x86_64-native-bsdapp-gcc install -Wl,-rpath=/usr/local/lib/gcc48 CC=gcc48
+
 Linux
 -----
 
@@ -190,7 +207,7 @@ devices managed by ``librte_pmd_bnx2x`` in Linux operating system.
 #. Bind the QLogic adapters to ``igb_uio`` or ``vfio-pci`` loaded in the
    previous step::
 
-      ./tools/dpdk_nic_bind.py --bind igb_uio 0000:84:00.0 0000:84:00.1
+      ./tools/dpdk-devbind.py --bind igb_uio 0000:84:00.0 0000:84:00.1
 
    or
 
@@ -202,7 +219,7 @@ devices managed by ``librte_pmd_bnx2x`` in Linux operating system.
 
       sudo chmod 0666 /dev/vfio/*
 
-      ./tools/dpdk_nic_bind.py --bind vfio-pci 0000:84:00.0 0000:84:00.1
+      ./tools/dpdk-devbind.py --bind vfio-pci 0000:84:00.0 0000:84:00.1
 
 #. Start ``testpmd`` with basic parameters:
 
@@ -297,7 +314,7 @@ This section provides instructions to configure SR-IOV with Linux OS.
 
 #. Assign VF MAC address:
 
-   Assign MAC address to the VF using iproute2 ulility. The syntax is:
+   Assign MAC address to the VF using iproute2 utility. The syntax is:
    ip link set <PF iface> vf <VF id> mac <macaddr>
 
    Example output:
@@ -307,7 +324,7 @@ This section provides instructions to configure SR-IOV with Linux OS.
       ip link set ens5f0 vf 0 mac 52:54:00:2f:9d:e8
 
 
-#. PCI passthrough:
+#. PCI Passthrough:
 
    The VF devices may be passed through to the guest VM using virt-manager or
    virsh etc. bnx2x PMD should be used to bind the VF devices in the guest VM