#include <rte_arp.h>
#include <rte_common.h>
#include <rte_ether.h>
-#include <rte_eth_ctrl.h>
#include <rte_icmp.h>
#include <rte_ip.h>
#include <rte_sctp.h>
#include <rte_udp.h>
#include <rte_byteorder.h>
#include <rte_esp.h>
+#include <rte_higig.h>
+#include <rte_mbuf.h>
+#include <rte_mbuf_dyn.h>
#ifdef __cplusplus
extern "C" {
* See struct rte_flow_item_mark.
*/
RTE_FLOW_ITEM_TYPE_MARK,
+
+ /**
+ * [META]
+ *
+ * Matches a metadata value.
+ *
+ * See struct rte_flow_item_meta.
+ */
+ RTE_FLOW_ITEM_TYPE_META,
+
+ /**
+ * Matches a GRE optional key field.
+ *
+ * The value should a big-endian 32bit integer.
+ *
+ * When this item present the K bit is implicitly matched as "1"
+ * in the default mask.
+ *
+ * @p spec/mask type:
+ * @code rte_be32_t * @endcode
+ */
+ RTE_FLOW_ITEM_TYPE_GRE_KEY,
+
+ /**
+ * Matches a GTP extension header: PDU session container.
+ *
+ * Configure flow for GTP packets with extension header type 0x85.
+ *
+ * See struct rte_flow_item_gtp_psc.
+ */
+ RTE_FLOW_ITEM_TYPE_GTP_PSC,
+
+ /**
+ * Matches a PPPoE header.
+ *
+ * Configure flow for PPPoE session packets.
+ *
+ * See struct rte_flow_item_pppoe.
+ */
+ RTE_FLOW_ITEM_TYPE_PPPOES,
+
+ /**
+ * Matches a PPPoE header.
+ *
+ * Configure flow for PPPoE discovery packets.
+ *
+ * See struct rte_flow_item_pppoe.
+ */
+ RTE_FLOW_ITEM_TYPE_PPPOED,
+
+ /**
+ * Matches a PPPoE optional proto_id field.
+ *
+ * It only applies to PPPoE session packets.
+ *
+ * See struct rte_flow_item_pppoe_proto_id.
+ */
+ RTE_FLOW_ITEM_TYPE_PPPOE_PROTO_ID,
+
+ /**
+ * Matches Network service header (NSH).
+ * See struct rte_flow_item_nsh.
+ *
+ */
+ RTE_FLOW_ITEM_TYPE_NSH,
+
+ /**
+ * Matches Internet Group Management Protocol (IGMP).
+ * See struct rte_flow_item_igmp.
+ *
+ */
+ RTE_FLOW_ITEM_TYPE_IGMP,
+
+ /**
+ * Matches IP Authentication Header (AH).
+ * See struct rte_flow_item_ah.
+ *
+ */
+ RTE_FLOW_ITEM_TYPE_AH,
+
+ /**
+ * Matches a HIGIG header.
+ * see struct rte_flow_item_higig2_hdr.
+ */
+ RTE_FLOW_ITEM_TYPE_HIGIG2,
+
+ /**
+ * [META]
+ *
+ * Matches a tag value.
+ *
+ * See struct rte_flow_item_tag.
+ */
+ RTE_FLOW_ITEM_TYPE_TAG,
+
+ /**
+ * Matches a L2TPv3 over IP header.
+ *
+ * Configure flow for L2TPv3 over IP packets.
+ *
+ * See struct rte_flow_item_l2tpv3oip.
+ */
+ RTE_FLOW_ITEM_TYPE_L2TPV3OIP,
+
+ /**
+ * Matches PFCP Header.
+ * See struct rte_flow_item_pfcp.
+ *
+ */
+ RTE_FLOW_ITEM_TYPE_PFCP,
+
};
+/**
+ *
+ * RTE_FLOW_ITEM_TYPE_HIGIG2
+ * Matches higig2 header
+ */
+RTE_STD_C11
+struct rte_flow_item_higig2_hdr {
+ struct rte_higig2_hdr hdr;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_HIGIG2. */
+#ifndef __cplusplus
+static const struct rte_flow_item_higig2_hdr rte_flow_item_higig2_hdr_mask = {
+ .hdr = {
+ .ppt1 = {
+ .classification = 0xffff,
+ .vid = 0xfff,
+ },
+ },
+};
+#endif
+
/**
* RTE_FLOW_ITEM_TYPE_ANY
*
* same order as on the wire.
*/
struct rte_flow_item_eth {
- struct ether_addr dst; /**< Destination MAC. */
- struct ether_addr src; /**< Source MAC. */
+ struct rte_ether_addr dst; /**< Destination MAC. */
+ struct rte_ether_addr src; /**< Source MAC. */
rte_be16_t type; /**< EtherType or TPID. */
};
* Matches an 802.1Q/ad VLAN tag.
*
* The corresponding standard outer EtherType (TPID) values are
- * ETHER_TYPE_VLAN or ETHER_TYPE_QINQ. It can be overridden by the preceding
- * pattern item.
+ * RTE_ETHER_TYPE_VLAN or RTE_ETHER_TYPE_QINQ. It can be overridden by
+ * the preceding pattern item.
*/
struct rte_flow_item_vlan {
rte_be16_t tci; /**< Tag control information. */
* Note: IPv4 options are handled by dedicated pattern items.
*/
struct rte_flow_item_ipv4 {
- struct ipv4_hdr hdr; /**< IPv4 header definition. */
+ struct rte_ipv4_hdr hdr; /**< IPv4 header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_IPV4. */
* RTE_FLOW_ITEM_TYPE_IPV6_EXT.
*/
struct rte_flow_item_ipv6 {
- struct ipv6_hdr hdr; /**< IPv6 header definition. */
+ struct rte_ipv6_hdr hdr; /**< IPv6 header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_IPV6. */
* Matches an ICMP header.
*/
struct rte_flow_item_icmp {
- struct icmp_hdr hdr; /**< ICMP header definition. */
+ struct rte_icmp_hdr hdr; /**< ICMP header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_ICMP. */
* Matches a UDP header.
*/
struct rte_flow_item_udp {
- struct udp_hdr hdr; /**< UDP header definition. */
+ struct rte_udp_hdr hdr; /**< UDP header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_UDP. */
* Matches a TCP header.
*/
struct rte_flow_item_tcp {
- struct tcp_hdr hdr; /**< TCP header definition. */
+ struct rte_tcp_hdr hdr; /**< TCP header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_TCP. */
* Matches a SCTP header.
*/
struct rte_flow_item_sctp {
- struct sctp_hdr hdr; /**< SCTP header definition. */
+ struct rte_sctp_hdr hdr; /**< SCTP header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_SCTP. */
* Matches a E-tag header.
*
* The corresponding standard outer EtherType (TPID) value is
- * ETHER_TYPE_ETAG. It can be overridden by the preceding pattern item.
+ * RTE_ETHER_TYPE_ETAG. It can be overridden by the preceding pattern item.
*/
struct rte_flow_item_e_tag {
/**
* Matches an ESP header.
*/
struct rte_flow_item_esp {
- struct esp_hdr hdr; /**< ESP header definition. */
+ struct rte_esp_hdr hdr; /**< ESP header definition. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_ESP. */
#ifndef __cplusplus
static const struct rte_flow_item_esp rte_flow_item_esp_mask = {
.hdr = {
- .spi = 0xffffffff,
+ .spi = RTE_BE32(0xffffffff),
},
};
#endif
uint8_t hln; /**< Hardware address length, normally 6. */
uint8_t pln; /**< Protocol address length, normally 4. */
rte_be16_t op; /**< Opcode (1 for request, 2 for reply). */
- struct ether_addr sha; /**< Sender hardware address. */
+ struct rte_ether_addr sha; /**< Sender hardware address. */
rte_be32_t spa; /**< Sender IPv4 address. */
- struct ether_addr tha; /**< Target hardware address. */
+ struct rte_ether_addr tha; /**< Target hardware address. */
rte_be32_t tpa; /**< Target IPv4 address. */
};
struct rte_flow_item_icmp6_nd_opt_sla_eth {
uint8_t type; /**< ND option type, normally 1. */
uint8_t length; /**< ND option length, normally 1. */
- struct ether_addr sla; /**< Source Ethernet LLA. */
+ struct rte_ether_addr sla; /**< Source Ethernet LLA. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_ICMP6_ND_OPT_SLA_ETH. */
struct rte_flow_item_icmp6_nd_opt_tla_eth {
uint8_t type; /**< ND option type, normally 2. */
uint8_t length; /**< ND option length, normally 1. */
- struct ether_addr tla; /**< Target Ethernet LLA. */
+ struct rte_ether_addr tla; /**< Target Ethernet LLA. */
};
/** Default mask for RTE_FLOW_ITEM_TYPE_ICMP6_ND_OPT_TLA_ETH. */
};
#endif
+/**
+ * RTE_FLOW_ITEM_TYPE_META
+ *
+ * Matches a specified metadata value. On egress, metadata can be set
+ * either by mbuf dynamic metadata field with PKT_TX_DYNF_METADATA flag or
+ * RTE_FLOW_ACTION_TYPE_SET_META. On ingress, RTE_FLOW_ACTION_TYPE_SET_META
+ * sets metadata for a packet and the metadata will be reported via mbuf
+ * metadata dynamic field with PKT_RX_DYNF_METADATA flag. The dynamic mbuf
+ * field must be registered in advance by rte_flow_dynf_metadata_register().
+ */
+struct rte_flow_item_meta {
+ uint32_t data;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_META. */
+#ifndef __cplusplus
+static const struct rte_flow_item_meta rte_flow_item_meta_mask = {
+ .data = UINT32_MAX,
+};
+#endif
+
+/**
+ * RTE_FLOW_ITEM_TYPE_GTP_PSC.
+ *
+ * Matches a GTP PDU extension header with type 0x85.
+ */
+struct rte_flow_item_gtp_psc {
+ uint8_t pdu_type; /**< PDU type. */
+ uint8_t qfi; /**< QoS flow identifier. */
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_GTP_PSC. */
+#ifndef __cplusplus
+static const struct rte_flow_item_gtp_psc
+rte_flow_item_gtp_psc_mask = {
+ .qfi = 0x3f,
+};
+#endif
+
+/**
+ * RTE_FLOW_ITEM_TYPE_PPPOE.
+ *
+ * Matches a PPPoE header.
+ */
+struct rte_flow_item_pppoe {
+ /**
+ * Version (4b), type (4b).
+ */
+ uint8_t version_type;
+ uint8_t code; /**< Message type. */
+ rte_be16_t session_id; /**< Session identifier. */
+ rte_be16_t length; /**< Payload length. */
+};
+
+/**
+ * RTE_FLOW_ITEM_TYPE_PPPOE_PROTO_ID.
+ *
+ * Matches a PPPoE optional proto_id field.
+ *
+ * It only applies to PPPoE session packets.
+ *
+ * Normally preceded by any of:
+ *
+ * - RTE_FLOW_ITEM_TYPE_PPPOE
+ * - RTE_FLOW_ITEM_TYPE_PPPOE_PROTO_ID
+ */
+struct rte_flow_item_pppoe_proto_id {
+ rte_be16_t proto_id; /**< PPP protocol identifier. */
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_PPPOE_PROTO_ID. */
+#ifndef __cplusplus
+static const struct rte_flow_item_pppoe_proto_id
+rte_flow_item_pppoe_proto_id_mask = {
+ .proto_id = RTE_BE16(0xffff),
+};
+#endif
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ITEM_TYPE_TAG
+ *
+ * Matches a specified tag value at the specified index.
+ */
+struct rte_flow_item_tag {
+ uint32_t data;
+ uint8_t index;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_TAG. */
+#ifndef __cplusplus
+static const struct rte_flow_item_tag rte_flow_item_tag_mask = {
+ .data = 0xffffffff,
+ .index = 0xff,
+};
+#endif
+
+/**
+ * RTE_FLOW_ITEM_TYPE_L2TPV3OIP.
+ *
+ * Matches a L2TPv3 over IP header.
+ */
+struct rte_flow_item_l2tpv3oip {
+ rte_be32_t session_id; /**< Session ID. */
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_L2TPV3OIP. */
+#ifndef __cplusplus
+static const struct rte_flow_item_l2tpv3oip rte_flow_item_l2tpv3oip_mask = {
+ .session_id = RTE_BE32(UINT32_MAX),
+};
+#endif
+
+
/**
* @warning
* @b EXPERIMENTAL: this structure may change without prior notice
uint32_t id; /**< Integer value to match against. */
};
+/** Default mask for RTE_FLOW_ITEM_TYPE_MARK. */
+#ifndef __cplusplus
+static const struct rte_flow_item_mark rte_flow_item_mark_mask = {
+ .id = 0xffffffff,
+};
+#endif
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ITEM_TYPE_NSH
+ *
+ * Match network service header (NSH), RFC 8300
+ *
+ */
+struct rte_flow_item_nsh {
+ uint32_t version:2;
+ uint32_t oam_pkt:1;
+ uint32_t reserved:1;
+ uint32_t ttl:6;
+ uint32_t length:6;
+ uint32_t reserved1:4;
+ uint32_t mdtype:4;
+ uint32_t next_proto:8;
+ uint32_t spi:24;
+ uint32_t sindex:8;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_NSH. */
+#ifndef __cplusplus
+static const struct rte_flow_item_nsh rte_flow_item_nsh_mask = {
+ .mdtype = 0xf,
+ .next_proto = 0xff,
+ .spi = 0xffffff,
+ .sindex = 0xff,
+};
+#endif
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ITEM_TYPE_IGMP
+ *
+ * Match Internet Group Management Protocol (IGMP), RFC 2236
+ *
+ */
+struct rte_flow_item_igmp {
+ uint32_t type:8;
+ uint32_t max_resp_time:8;
+ uint32_t checksum:16;
+ uint32_t group_addr;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_IGMP. */
+#ifndef __cplusplus
+static const struct rte_flow_item_igmp rte_flow_item_igmp_mask = {
+ .group_addr = 0xffffffff,
+};
+#endif
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ITEM_TYPE_AH
+ *
+ * Match IP Authentication Header (AH), RFC 4302
+ *
+ */
+struct rte_flow_item_ah {
+ uint32_t next_hdr:8;
+ uint32_t payload_len:8;
+ uint32_t reserved:16;
+ uint32_t spi;
+ uint32_t seq_num;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_AH. */
+#ifndef __cplusplus
+static const struct rte_flow_item_ah rte_flow_item_ah_mask = {
+ .spi = 0xffffffff,
+};
+#endif
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ITEM_TYPE_PFCP
+ *
+ * Match PFCP Header
+ */
+struct rte_flow_item_pfcp {
+ uint8_t s_field;
+ uint8_t msg_type;
+ rte_be16_t msg_len;
+ rte_be64_t seid;
+};
+
+/** Default mask for RTE_FLOW_ITEM_TYPE_PFCP. */
+#ifndef __cplusplus
+static const struct rte_flow_item_pfcp rte_flow_item_pfcp_mask = {
+ .s_field = 0x01,
+ .seid = RTE_BE64(0xffffffffffffffff),
+};
+#endif
+
/**
* Matching pattern item definition.
*
/**
* Action types.
*
- * Each possible action is represented by a type. Some have associated
- * configuration structures. Several actions combined in a list can be
- * assigned to a flow rule and are performed in order.
+ * Each possible action is represented by a type.
+ * An action can have an associated configuration object.
+ * Several actions combined in a list can be assigned
+ * to a flow rule and are performed in order.
*
* They fall in three categories:
*
*/
RTE_FLOW_ACTION_TYPE_NVGRE_DECAP,
+ /**
+ * Add outer header whose template is provided in its data buffer
+ *
+ * See struct rte_flow_action_raw_encap.
+ */
+ RTE_FLOW_ACTION_TYPE_RAW_ENCAP,
+
+ /**
+ * Remove outer header whose template is provided in its data buffer.
+ *
+ * See struct rte_flow_action_raw_decap
+ */
+ RTE_FLOW_ACTION_TYPE_RAW_DECAP,
+
/**
* Modify IPv4 source address in the outermost IPv4 header.
*
* No associated configuration structure.
*/
RTE_FLOW_ACTION_TYPE_MAC_SWAP,
+
+ /**
+ * Decrease TTL value directly
+ *
+ * No associated configuration structure.
+ */
+ RTE_FLOW_ACTION_TYPE_DEC_TTL,
+
+ /**
+ * Set TTL value
+ *
+ * See struct rte_flow_action_set_ttl
+ */
+ RTE_FLOW_ACTION_TYPE_SET_TTL,
+
+ /**
+ * Set source MAC address from matched flow.
+ *
+ * If flow pattern does not define a valid RTE_FLOW_ITEM_TYPE_ETH,
+ * the PMD should return a RTE_FLOW_ERROR_TYPE_ACTION error.
+ *
+ * See struct rte_flow_action_set_mac.
+ */
+ RTE_FLOW_ACTION_TYPE_SET_MAC_SRC,
+
+ /**
+ * Set destination MAC address from matched flow.
+ *
+ * If flow pattern does not define a valid RTE_FLOW_ITEM_TYPE_ETH,
+ * the PMD should return a RTE_FLOW_ERROR_TYPE_ACTION error.
+ *
+ * See struct rte_flow_action_set_mac.
+ */
+ RTE_FLOW_ACTION_TYPE_SET_MAC_DST,
+
+ /**
+ * Increase sequence number in the outermost TCP header.
+ *
+ * Action configuration specifies the value to increase
+ * TCP sequence number as a big-endian 32 bit integer.
+ *
+ * @p conf type:
+ * @code rte_be32_t * @endcode
+ *
+ * Using this action on non-matching traffic will result in
+ * undefined behavior.
+ */
+ RTE_FLOW_ACTION_TYPE_INC_TCP_SEQ,
+
+ /**
+ * Decrease sequence number in the outermost TCP header.
+ *
+ * Action configuration specifies the value to decrease
+ * TCP sequence number as a big-endian 32 bit integer.
+ *
+ * @p conf type:
+ * @code rte_be32_t * @endcode
+ *
+ * Using this action on non-matching traffic will result in
+ * undefined behavior.
+ */
+ RTE_FLOW_ACTION_TYPE_DEC_TCP_SEQ,
+
+ /**
+ * Increase acknowledgment number in the outermost TCP header.
+ *
+ * Action configuration specifies the value to increase
+ * TCP acknowledgment number as a big-endian 32 bit integer.
+ *
+ * @p conf type:
+ * @code rte_be32_t * @endcode
+
+ * Using this action on non-matching traffic will result in
+ * undefined behavior.
+ */
+ RTE_FLOW_ACTION_TYPE_INC_TCP_ACK,
+
+ /**
+ * Decrease acknowledgment number in the outermost TCP header.
+ *
+ * Action configuration specifies the value to decrease
+ * TCP acknowledgment number as a big-endian 32 bit integer.
+ *
+ * @p conf type:
+ * @code rte_be32_t * @endcode
+ *
+ * Using this action on non-matching traffic will result in
+ * undefined behavior.
+ */
+ RTE_FLOW_ACTION_TYPE_DEC_TCP_ACK,
+
+ /**
+ * Set Tag.
+ *
+ * Tag is for internal flow usage only and
+ * is not delivered to the application.
+ *
+ * See struct rte_flow_action_set_tag.
+ */
+ RTE_FLOW_ACTION_TYPE_SET_TAG,
+
+ /**
+ * Set metadata on ingress or egress path.
+ *
+ * See struct rte_flow_action_set_meta.
+ */
+ RTE_FLOW_ACTION_TYPE_SET_META,
+
+ /**
+ * Modify IPv4 DSCP in the outermost IP header.
+ *
+ * If flow pattern does not define a valid RTE_FLOW_ITEM_TYPE_IPV4,
+ * then the PMD should return a RTE_FLOW_ERROR_TYPE_ACTION error.
+ *
+ * See struct rte_flow_action_set_dscp.
+ */
+ RTE_FLOW_ACTION_TYPE_SET_IPV4_DSCP,
+
+ /**
+ * Modify IPv6 DSCP in the outermost IP header.
+ *
+ * If flow pattern does not define a valid RTE_FLOW_ITEM_TYPE_IPV6,
+ * then the PMD should return a RTE_FLOW_ERROR_TYPE_ACTION error.
+ *
+ * See struct rte_flow_action_set_dscp.
+ */
+ RTE_FLOW_ACTION_TYPE_SET_IPV6_DSCP,
+
+ /**
+ * Report as aged flow if timeout passed without any matching on the
+ * flow.
+ *
+ * See struct rte_flow_action_age.
+ * See function rte_flow_get_aged_flows
+ * see enum RTE_ETH_EVENT_FLOW_AGED
+ */
+ RTE_FLOW_ACTION_TYPE_AGE,
};
/**
uint16_t index; /**< Queue index to use. */
};
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ACTION_TYPE_AGE
+ *
+ * Report flow as aged-out if timeout passed without any matching
+ * on the flow. RTE_ETH_EVENT_FLOW_AGED event is triggered when a
+ * port detects new aged-out flows.
+ *
+ * The flow context and the flow handle will be reported by the
+ * rte_flow_get_aged_flows API.
+ */
+struct rte_flow_action_age {
+ uint32_t timeout:24; /**< Time in seconds. */
+ uint32_t reserved:8; /**< Reserved, must be zero. */
+ void *context;
+ /**< The user flow context, NULL means the rte_flow pointer. */
+};
/**
* @warning
uint64_t bytes; /**< Number of bytes through this rule [out]. */
};
+/**
+ * Hash function types.
+ */
+enum rte_eth_hash_function {
+ RTE_ETH_HASH_FUNCTION_DEFAULT = 0,
+ RTE_ETH_HASH_FUNCTION_TOEPLITZ, /**< Toeplitz */
+ RTE_ETH_HASH_FUNCTION_SIMPLE_XOR, /**< Simple XOR */
+ /**
+ * Symmetric Toeplitz: src, dst will be replaced by
+ * xor(src, dst). For the case with src/dst only,
+ * src or dst address will xor with zero pair.
+ */
+ RTE_ETH_HASH_FUNCTION_SYMMETRIC_TOEPLITZ,
+ RTE_ETH_HASH_FUNCTION_MAX,
+};
+
/**
* RTE_FLOW_ACTION_TYPE_RSS
*
* direction.
*
* Multiple flows can be configured to use the same security session.
+ *
+ * The NULL value is allowed for security session. If security session is NULL,
+ * then SPI field in ESP flow item and IP addresses in flow items 'IPv4' and
+ * 'IPv6' will be allowed to be a range. The rule thus created can enable
+ * security processing on multiple flows.
*/
struct rte_flow_action_security {
void *security_session; /**< Pointer to security session structure. */
struct rte_flow_item *definition;
};
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ACTION_TYPE_RAW_ENCAP
+ *
+ * Raw tunnel end-point encapsulation data definition.
+ *
+ * The data holds the headers definitions to be applied on the packet.
+ * The data must start with ETH header up to the tunnel item header itself.
+ * When used right after RAW_DECAP (for decapsulating L3 tunnel type for
+ * example MPLSoGRE) the data will just hold layer 2 header.
+ *
+ * The preserve parameter holds which bits in the packet the PMD is not allowed
+ * to change, this parameter can also be NULL and then the PMD is allowed
+ * to update any field.
+ *
+ * size holds the number of bytes in @p data and @p preserve.
+ */
+struct rte_flow_action_raw_encap {
+ uint8_t *data; /**< Encapsulation data. */
+ uint8_t *preserve; /**< Bit-mask of @p data to preserve on output. */
+ size_t size; /**< Size of @p data and @p preserve. */
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ACTION_TYPE_RAW_DECAP
+ *
+ * Raw tunnel end-point decapsulation data definition.
+ *
+ * The data holds the headers definitions to be removed from the packet.
+ * The data must start with ETH header up to the tunnel item header itself.
+ * When used right before RAW_DECAP (for encapsulating L3 tunnel type for
+ * example MPLSoGRE) the data will just hold layer 2 header.
+ *
+ * size holds the number of bytes in @p data.
+ */
+struct rte_flow_action_raw_decap {
+ uint8_t *data; /**< Encapsulation data. */
+ size_t size; /**< Size of @p data and @p preserve. */
+};
+
/**
* @warning
* @b EXPERIMENTAL: this structure may change without prior notice
rte_be16_t port;
};
+/**
+ * RTE_FLOW_ACTION_TYPE_SET_TTL
+ *
+ * Set the TTL value directly for IPv4 or IPv6
+ */
+struct rte_flow_action_set_ttl {
+ uint8_t ttl_value;
+};
+
+/**
+ * RTE_FLOW_ACTION_TYPE_SET_MAC
+ *
+ * Set MAC address from the matched flow
+ */
+struct rte_flow_action_set_mac {
+ uint8_t mac_addr[RTE_ETHER_ADDR_LEN];
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ACTION_TYPE_SET_TAG
+ *
+ * Set a tag which is a transient data used during flow matching. This is not
+ * delivered to application. Multiple tags are supported by specifying index.
+ */
+struct rte_flow_action_set_tag {
+ uint32_t data;
+ uint32_t mask;
+ uint8_t index;
+};
+
+/**
+ * @warning
+ * @b EXPERIMENTAL: this structure may change without prior notice
+ *
+ * RTE_FLOW_ACTION_TYPE_SET_META
+ *
+ * Set metadata. Metadata set by mbuf metadata dynamic field with
+ * PKT_TX_DYNF_DATA flag on egress will be overridden by this action. On
+ * ingress, the metadata will be carried by mbuf metadata dynamic field
+ * with PKT_RX_DYNF_METADATA flag if set. The dynamic mbuf field must be
+ * registered in advance by rte_flow_dynf_metadata_register().
+ *
+ * Altering partial bits is supported with mask. For bits which have never
+ * been set, unpredictable value will be seen depending on driver
+ * implementation. For loopback/hairpin packet, metadata set on Rx/Tx may
+ * or may not be propagated to the other path depending on HW capability.
+ *
+ * RTE_FLOW_ITEM_TYPE_META matches metadata.
+ */
+struct rte_flow_action_set_meta {
+ uint32_t data;
+ uint32_t mask;
+};
+
+/**
+ * RTE_FLOW_ACTION_TYPE_SET_IPV4_DSCP
+ * RTE_FLOW_ACTION_TYPE_SET_IPV6_DSCP
+ *
+ * Set the DSCP value for IPv4/IPv6 header.
+ * DSCP in low 6 bits, rest ignored.
+ */
+struct rte_flow_action_set_dscp {
+ uint8_t dscp;
+};
+
+/* Mbuf dynamic field offset for metadata. */
+extern int rte_flow_dynf_metadata_offs;
+
+/* Mbuf dynamic field flag mask for metadata. */
+extern uint64_t rte_flow_dynf_metadata_mask;
+
+/* Mbuf dynamic field pointer for metadata. */
+#define RTE_FLOW_DYNF_METADATA(m) \
+ RTE_MBUF_DYNFIELD((m), rte_flow_dynf_metadata_offs, uint32_t *)
+
+/* Mbuf dynamic flags for metadata. */
+#define PKT_RX_DYNF_METADATA (rte_flow_dynf_metadata_mask)
+#define PKT_TX_DYNF_METADATA (rte_flow_dynf_metadata_mask)
+
+__rte_experimental
+static inline uint32_t
+rte_flow_dynf_metadata_get(struct rte_mbuf *m)
+{
+ return *RTE_FLOW_DYNF_METADATA(m);
+}
+
+__rte_experimental
+static inline void
+rte_flow_dynf_metadata_set(struct rte_mbuf *m, uint32_t v)
+{
+ *RTE_FLOW_DYNF_METADATA(m) = v;
+}
+
/*
* Definition of a single action.
*
* A list of actions is terminated by a END action.
*
- * For simple actions without a configuration structure, conf remains NULL.
+ * For simple actions without a configuration object, conf remains NULL.
*/
struct rte_flow_action {
enum rte_flow_action_type type; /**< Action type. */
- const void *conf; /**< Pointer to action configuration structure. */
+ const void *conf; /**< Pointer to action configuration object. */
};
/**
RTE_FLOW_CONV_OP_ACTION_NAME_PTR,
};
+/**
+ * @warning
+ * @b EXPERIMENTAL: this API may change without prior notice.
+ *
+ * Dump hardware internal representation information of
+ * rte flow to file.
+ *
+ * @param[in] port_id
+ * The port identifier of the Ethernet device.
+ * @param[in] file
+ * A pointer to a file for output.
+ * @param[out] error
+ * Perform verbose error reporting if not NULL. PMDs initialize this
+ * structure in case of error only.
+ * @return
+ * 0 on success, a nagative value otherwise.
+ */
+__rte_experimental
+int
+rte_flow_dev_dump(uint16_t port_id, FILE *file, struct rte_flow_error *error);
+
+/**
+ * Check if mbuf dynamic field for metadata is registered.
+ *
+ * @return
+ * True if registered, false otherwise.
+ */
+__rte_experimental
+static inline int
+rte_flow_dynf_metadata_avail(void)
+{
+ return !!rte_flow_dynf_metadata_mask;
+}
+
+/**
+ * Register mbuf dynamic field and flag for metadata.
+ *
+ * This function must be called prior to use SET_META action in order to
+ * register the dynamic mbuf field. Otherwise, the data cannot be delivered to
+ * application.
+ *
+ * @return
+ * 0 on success, a negative errno value otherwise and rte_errno is set.
+ */
+__rte_experimental
+int
+rte_flow_dynf_metadata_register(void);
+
/**
* Check whether a flow rule can be created on a given port.
*
const void *src,
struct rte_flow_error *error);
+/**
+ * Get aged-out flows of a given port.
+ *
+ * RTE_ETH_EVENT_FLOW_AGED event will be triggered when at least one new aged
+ * out flow was detected after the last call to rte_flow_get_aged_flows.
+ * This function can be called to get the aged flows usynchronously from the
+ * event callback or synchronously regardless the event.
+ * This is not safe to call rte_flow_get_aged_flows function with other flow
+ * functions from multiple threads simultaneously.
+ *
+ * @param port_id
+ * Port identifier of Ethernet device.
+ * @param[in, out] contexts
+ * The address of an array of pointers to the aged-out flows contexts.
+ * @param[in] nb_contexts
+ * The length of context array pointers.
+ * @param[out] error
+ * Perform verbose error reporting if not NULL. Initialized in case of
+ * error only.
+ *
+ * @return
+ * if nb_contexts is 0, return the amount of all aged contexts.
+ * if nb_contexts is not 0 , return the amount of aged flows reported
+ * in the context array, otherwise negative errno value.
+ *
+ * @see rte_flow_action_age
+ * @see RTE_ETH_EVENT_FLOW_AGED
+ */
+__rte_experimental
+int
+rte_flow_get_aged_flows(uint16_t port_id, void **contexts,
+ uint32_t nb_contexts, struct rte_flow_error *error);
+
#ifdef __cplusplus
}
#endif
git.droids-corp.org / dpdk.git / blobdiff