1 .. SPDX-License-Identifier: BSD-3-Clause
2 Copyright(c) 2019-2021 Xilinx, Inc.
3 Copyright(c) 2016-2019 Solarflare Communications Inc.
5 This software was jointly developed between OKTET Labs (under contract
6 for Solarflare) and Solarflare Communications, Inc.
8 Solarflare libefx-based Poll Mode Driver
9 ========================================
11 The SFC EFX PMD (**librte_net_sfc_efx**) provides poll mode driver support
12 for **Solarflare SFN7xxx and SFN8xxx** family of 10/40 Gbps adapters,
13 **Solarflare XtremeScale X2xxx** family of 10/25/40/50/100 Gbps adapters and
14 **Alveo SN1000 SmartNICs** family of 10/25/40/50/100 Gbps adapters.
15 SFC EFX PMD has support for the latest Linux and FreeBSD operating systems.
17 More information can be found at `Solarflare Communications website
18 <http://solarflare.com>`_.
24 SFC EFX PMD has support for:
26 - Multiple transmit and receive queues
28 - Link state information including link status change interrupt
30 - IPv4/IPv6 TCP/UDP transmit checksum offload
32 - Inner IPv4/IPv6 TCP/UDP transmit checksum offload
34 - Port hardware statistics
36 - Extended statistics (see Solarflare Server Adapter User's Guide for
37 the statistics description)
43 - Jumbo frames up to 9K
49 - TCP segmentation offload (TSO) including VXLAN and GENEVE encapsulated
51 - Multicast MAC filter
53 - IPv4/IPv6 TCP/UDP receive checksum offload
55 - Inner IPv4/IPv6 TCP/UDP receive checksum offload
57 - Received packet type information
59 - Receive side scaling (RSS)
63 - Scattered Rx DMA for packet that are larger that a single Rx descriptor
65 - Receive queue interrupts
67 - Deferred receive and transmit queue start
69 - Transmit VLAN insertion (if running firmware variant supports it)
77 - Port representors (see :ref: switch_representation)
80 Non-supported Features
81 ----------------------
83 The features not yet supported include:
85 - Priority-based flow control
87 - Configurable RX CRC stripping (always stripped)
89 - Header split on receive
101 Due to requirements on receive buffer alignment and usage of the receive
102 buffer for the auxiliary packet information provided by the NIC up to
103 extra 269 (14 bytes prefix plus up to 255 bytes for end padding) bytes may be
104 required in the receive buffer.
105 It should be taken into account when mbuf pool for receive is created.
108 Equal stride super-buffer mode
109 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
111 When the receive queue uses equal stride super-buffer DMA mode, one HW Rx
112 descriptor carries many Rx buffers which contiguously follow each other
113 with some stride (equal to total size of rte_mbuf as mempool object).
114 Each Rx buffer is an independent rte_mbuf.
115 However dedicated mempool manager must be used when mempool for the Rx
116 queue is created. The manager must support dequeue of the contiguous
117 block of objects and provide mempool info API to get the block size.
119 Another limitation of a equal stride super-buffer mode, imposed by the
120 firmware, is that it allows for a single RSS context.
126 NVGRE, VXLAN and GENEVE tunnels are supported on SFN8xxx and X2xxx family
127 adapters with full-feature firmware variant running.
128 **sfboot** should be used to configure NIC to run full-feature firmware variant.
129 See Solarflare Server Adapter User's Guide for details.
131 SFN8xxx and X2xxx family adapters provide either inner or outer packet classes.
132 If adapter firmware advertises support for tunnels then the PMD
133 configures the hardware to report inner classes, and outer classes are
134 not reported in received packets.
135 However, for VXLAN and GENEVE tunnels the PMD does report UDP as the
136 outer layer 4 packet type.
138 SFN8xxx and X2xxx family adapters report GENEVE packets as VXLAN.
139 If UDP ports are configured for only one tunnel type then it is safe to
140 treat VXLAN packet type indication as the corresponding UDP tunnel type.
146 Supported attributes:
151 Supported pattern items (***non-transfer*** rules):
155 - ETH (exact match of source/destination addresses, individual/group match
156 of destination address, EtherType in the outer frame and exact match of
157 destination addresses, individual/group match of destination address in
160 - VLAN (exact match of VID, double-tagging is supported)
162 - IPV4 (exact match of source/destination addresses,
163 IP transport protocol)
165 - IPV6 (exact match of source/destination addresses,
166 IP transport protocol)
168 - TCP (exact match of source/destination ports)
170 - UDP (exact match of source/destination ports)
172 - VXLAN (exact match of VXLAN network identifier)
174 - GENEVE (exact match of virtual network identifier, only Ethernet (0x6558)
175 protocol type is supported)
177 - NVGRE (exact match of virtual subnet ID)
179 Supported actions (***non-transfer*** rules):
189 - FLAG (supported only with ef10_essb Rx datapath)
191 - MARK (supported only with ef10_essb Rx datapath)
193 Supported pattern items (***transfer*** rules):
195 - PORT_REPRESENTOR (cannot repeat; conflicts with other traffic source items)
197 - REPRESENTED_PORT (cannot repeat; conflicts with other traffic source items)
199 - PORT_ID (cannot repeat; conflicts with other traffic source items)
201 - PHY_PORT (cannot repeat; conflicts with other traffic source items)
203 - PF (cannot repeat; conflicts with other traffic source items)
205 - VF (cannot repeat; conflicts with other traffic source items)
209 - VLAN (double-tagging is supported)
211 - IPV4 (source/destination addresses, IP transport protocol,
212 type of service, time to live)
214 - IPV6 (source/destination addresses, IP transport protocol,
215 traffic class, hop limit)
217 - TCP (source/destination ports, TCP header length + TCP flags)
219 - UDP (source/destination ports)
221 - VXLAN (exact match of VXLAN network identifier)
223 - GENEVE (exact match of virtual network identifier)
225 - NVGRE (exact match of virtual subnet ID)
227 Supported actions (***transfer*** rules):
257 Validating flow rules depends on the firmware variant.
259 The :ref:`flow_isolated_mode` is supported.
261 The implementation is natively thread-safe.
263 Ethernet destination individual/group match
264 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
266 Ethernet item supports I/G matching, if only the corresponding bit is set
267 in the mask of destination address. If destination address in the spec is
268 multicast, it matches all multicast (and broadcast) packets, otherwise it
269 matches unicast packets that are not filtered by other flow rules.
271 Exceptions to flow rules
272 ~~~~~~~~~~~~~~~~~~~~~~~~
274 There is a list of exceptional flow rule patterns which will not be
275 accepted by the PMD. A pattern will be rejected if at least one of the
278 - Filtering by IPv4 or IPv6 EtherType without pattern items of internet
281 - The last item is IPV4 or IPV6, and it's empty.
283 - Filtering by TCP or UDP IP transport protocol without pattern items of
284 transport layer and above.
286 - The last item is TCP or UDP, and it's empty.
294 - Alveo SN1022 SmartNIC
296 - Solarflare XtremeScale Adapters:
298 - Solarflare X2522 Dual Port SFP28 10/25GbE Adapter
300 - Solarflare X2541 Single Port QSFP28 10/25G/100G Adapter
302 - Solarflare X2542 Dual Port QSFP28 10/25G/100G Adapter
304 - Solarflare Flareon [Ultra] Server Adapters:
306 - Solarflare SFN8522 Dual Port SFP+ Server Adapter
308 - Solarflare SFN8522M Dual Port SFP+ Server Adapter
310 - Solarflare SFN8042 Dual Port QSFP+ Server Adapter
312 - Solarflare SFN8542 Dual Port QSFP+ Server Adapter
314 - Solarflare SFN8722 Dual Port SFP+ OCP Server Adapter
316 - Solarflare SFN7002F Dual Port SFP+ Server Adapter
318 - Solarflare SFN7004F Quad Port SFP+ Server Adapter
320 - Solarflare SFN7042Q Dual Port QSFP+ Server Adapter
322 - Solarflare SFN7122F Dual Port SFP+ Server Adapter
324 - Solarflare SFN7124F Quad Port SFP+ Server Adapter
326 - Solarflare SFN7142Q Dual Port QSFP+ Server Adapter
328 - Solarflare SFN7322F Precision Time Synchronization Server Adapter
334 - Requires firmware version:
336 - SFN7xxx: **4.7.1.1001** or higher
338 - SFN8xxx: **6.0.2.1004** or higher
340 Visit `Solarflare Support Downloads <https://support.solarflare.com>`_ to get
341 Solarflare Utilities (either Linux or FreeBSD) with the latest firmware.
342 Follow instructions from Solarflare Server Adapter User's Guide to
343 update firmware and configure the adapter.
346 Pre-Installation Configuration
347 ------------------------------
353 The following build-time options may be enabled on build time using
354 ``-Dc_args=`` meson argument (e.g. ``-Dc_args=-DRTE_LIBRTE_SFC_EFX_DEBUG``).
356 Please note that enabling debugging options may affect system performance.
358 - ``RTE_LIBRTE_SFC_EFX_DEBUG`` (undefined by default)
360 Enable compilation of the extra run-time consistency checks.
363 Per-Device Parameters
364 ~~~~~~~~~~~~~~~~~~~~~
366 The following per-device parameters can be passed via EAL PCI device
367 allow option like "-a 02:00.0,arg1=value1,...".
369 Case-insensitive 1/y/yes/on or 0/n/no/off may be used to specify
370 boolean parameters value.
372 - ``class`` [net|vdpa] (default **net**)
374 Choose the mode of operation of ef100 device.
375 **net** device will work as network device and will be probed by net/sfc driver.
376 **vdpa** device will work as vdpa device and will be probed by vdpa/sfc driver.
377 If this parameter is not specified then ef100 device will operate as
380 - ``switch_mode`` [legacy|switchdev] (see below for default)
382 In legacy mode, NIC firmware provides Ethernet virtual bridging (EVB) API
383 to configure switching inside NIC to deliver traffic to physical (PF) and
384 virtual (VF) PCI functions. PF driver is responsible to build the
385 infrastructure for VFs, and traffic goes to/from VF by default in accordance
386 with MAC address assigned, permissions and filters installed by VF drivers.
387 In switchdev mode VF traffic goes via port representor (if any) on PF, and
388 software virtual switch (for example, Open vSwitch) makes the decision.
389 Software virtual switch may install MAE rules to pass established traffic
390 flows via hardware and offload software datapath as the result.
391 Default is legacy, unless representors are specified, in which case switchdev
394 - ``representor`` parameter [list]
396 Instantiate port representor Ethernet devices for specified Virtual
399 It is a standard parameter whose format is described in
400 :ref:`ethernet_device_standard_device_arguments`.
402 - ``rx_datapath`` [auto|efx|ef10|ef10_essb] (default **auto**)
404 Choose receive datapath implementation.
405 **auto** allows the driver itself to make a choice based on firmware
406 features available and required by the datapath implementation.
407 **efx** chooses libefx-based datapath which supports Rx scatter.
408 Supported for SFN7xxx, SFN8xxx and X2xxx family adapters only.
409 **ef10** chooses EF10 (SFN7xxx, SFN8xxx, X2xxx) native datapath which is
410 more efficient than libefx-based and provides richer packet type
412 **ef10_essb** chooses SFNX2xxx equal stride super-buffer datapath
413 which may be used on DPDK firmware variant only
414 (see notes about its limitations above).
415 **ef100** chooses EF100 native datapath which is the only supported
416 Rx datapath for EF100 architecture based NICs.
418 - ``tx_datapath`` [auto|efx|ef10|ef10_simple|ef100] (default **auto**)
420 Choose transmit datapath implementation.
421 **auto** allows the driver itself to make a choice based on firmware
422 features available and required by the datapath implementation.
423 **efx** chooses libefx-based datapath which supports VLAN insertion
424 (full-feature firmware variant only), TSO and multi-segment mbufs.
425 Mbuf segments may come from different mempools, and mbuf reference
426 counters are treated responsibly.
427 Supported for SFN7xxx, SFN8xxx and X2xxx family adapters only.
428 **ef10** chooses EF10 (SFN7xxx, SFN8xxx, X2xxx) native datapath which is
429 more efficient than libefx-based but has no VLAN insertion support yet.
430 Mbuf segments may come from different mempools, and mbuf reference
431 counters are treated responsibly.
432 **ef10_simple** chooses EF10 (SFN7xxx, SFN8xxx, X2xxx) native datapath which
433 is even more faster then **ef10** but does not support multi-segment
434 mbufs, disallows multiple mempools and neglects mbuf reference counters.
435 **ef100** chooses EF100 native datapath which supports multi-segment
436 mbufs, VLAN insertion, inner/outer IPv4 and TCP/UDP checksum and TCP
437 segmentation offloads including VXLAN and GENEVE IPv4/IPv6 tunnels.
439 - ``perf_profile`` [auto|throughput|low-latency] (default **throughput**)
441 Choose hardware tuning to be optimized for either throughput or
443 **auto** allows NIC firmware to make a choice based on
444 installed licenses and firmware variant configured using **sfboot**.
446 - ``stats_update_period_ms`` [long] (default **1000**)
448 Adjust period in milliseconds to update port hardware statistics.
449 The accepted range is 0 to 65535. The value of **0** may be used
450 to disable periodic statistics update. One should note that it's
451 only possible to set an arbitrary value on SFN8xxx and X2xxx provided that
452 firmware version is 6.2.1.1033 or higher, otherwise any positive
453 value will select a fixed update period of **1000** milliseconds
455 - ``fw_variant`` [dont-care|full-feature|ultra-low-latency|
456 capture-packed-stream|dpdk] (default **dont-care**)
458 Choose the preferred firmware variant to use.
459 The parameter is supported for SFN7xxX, SFN8xxx and X2xxx families only.
460 In order for the selected option to have an effect, the **sfboot** utility
461 must be configured with the **auto** firmware-variant option.
462 The preferred firmware variant applies to all ports on the NIC.
463 **dont-care** ensures that the driver can attach to an unprivileged function.
464 The datapath firmware type to use is controlled by the **sfboot**
466 **full-feature** chooses full featured firmware.
467 **ultra-low-latency** chooses firmware with fewer features but lower latency.
468 **capture-packed-stream** chooses firmware for SolarCapture packed stream
470 **dpdk** chooses DPDK firmware with equal stride super-buffer Rx mode
471 for higher Rx packet rate and packet marks support and firmware subvariant
472 without checksumming on transmit for higher Tx packet rate if
473 checksumming is not required.
475 - ``rxd_wait_timeout_ns`` [long] (default **200 us**)
477 Adjust timeout in nanoseconds to head-of-line block to wait for
479 The accepted range is 0 to 400 ms.
480 Flow control should be enabled to make it work.
481 The value of **0** disables it and packets are dropped immediately.
482 When a packet is dropped because of no Rx descriptors,
483 ``rx_nodesc_drop_cnt`` counter grows.
484 The feature is supported only by the DPDK firmware variant when equal
485 stride super-buffer Rx mode is used.
488 Dynamic Logging Parameters
489 ~~~~~~~~~~~~~~~~~~~~~~~~~~
491 One may leverage EAL option "--log-level" to change default levels
492 for the log types supported by the driver. The option is used with
493 an argument typically consisting of two parts separated by a colon.
495 Level value is the last part which takes a symbolic name (or integer).
496 Log type is the former part which may shell match syntax.
497 Depending on the choice of the expression, the given log level may
498 be used either for some specific log type or for a subset of types.
500 SFC EFX PMD provides the following log types available for control:
502 - ``pmd.net.sfc.driver`` (default level is **notice**)
504 Affects driver-wide messages unrelated to any particular devices.
506 - ``pmd.net.sfc.main`` (default level is **notice**)
508 Matches a subset of per-port log types registered during runtime.
509 A full name for a particular type may be obtained by appending a
510 dot and a PCI device identifier (``XXXX:XX:XX.X``) to the prefix.
512 - ``pmd.net.sfc.mcdi`` (default level is **notice**)
514 Extra logging of the communication with the NIC's management CPU.
515 The format of the log is consumed by the Solarflare netlogdecode
516 cross-platform tool. May be managed per-port, as explained above.