1 /* SPDX-License-Identifier: BSD-3-Clause
2 * Copyright 2015 6WIND S.A.
3 * Copyright 2015 Mellanox Technologies, Ltd
16 #include <linux/rtnetlink.h>
19 /* ISO C doesn't support unnamed structs/unions, disabling -pedantic. */
21 #pragma GCC diagnostic ignored "-Wpedantic"
23 #include <infiniband/verbs.h>
25 #pragma GCC diagnostic error "-Wpedantic"
28 #include <rte_malloc.h>
29 #include <rte_ethdev_driver.h>
30 #include <rte_ethdev_pci.h>
32 #include <rte_bus_pci.h>
33 #include <rte_common.h>
34 #include <rte_config.h>
35 #include <rte_eal_memconfig.h>
36 #include <rte_kvargs.h>
37 #include <rte_rwlock.h>
38 #include <rte_spinlock.h>
39 #include <rte_string_fns.h>
40 #include <rte_alarm.h>
43 #include "mlx5_utils.h"
44 #include "mlx5_rxtx.h"
45 #include "mlx5_autoconf.h"
46 #include "mlx5_defs.h"
47 #include "mlx5_glue.h"
49 #include "mlx5_flow.h"
51 /* Device parameter to enable RX completion queue compression. */
52 #define MLX5_RXQ_CQE_COMP_EN "rxq_cqe_comp_en"
54 /* Device parameter to enable RX completion entry padding to 128B. */
55 #define MLX5_RXQ_CQE_PAD_EN "rxq_cqe_pad_en"
57 /* Device parameter to enable padding Rx packet to cacheline size. */
58 #define MLX5_RXQ_PKT_PAD_EN "rxq_pkt_pad_en"
60 /* Device parameter to enable Multi-Packet Rx queue. */
61 #define MLX5_RX_MPRQ_EN "mprq_en"
63 /* Device parameter to configure log 2 of the number of strides for MPRQ. */
64 #define MLX5_RX_MPRQ_LOG_STRIDE_NUM "mprq_log_stride_num"
66 /* Device parameter to limit the size of memcpy'd packet for MPRQ. */
67 #define MLX5_RX_MPRQ_MAX_MEMCPY_LEN "mprq_max_memcpy_len"
69 /* Device parameter to set the minimum number of Rx queues to enable MPRQ. */
70 #define MLX5_RXQS_MIN_MPRQ "rxqs_min_mprq"
72 /* Device parameter to configure inline send. Deprecated, ignored.*/
73 #define MLX5_TXQ_INLINE "txq_inline"
75 /* Device parameter to limit packet size to inline with ordinary SEND. */
76 #define MLX5_TXQ_INLINE_MAX "txq_inline_max"
78 /* Device parameter to configure minimal data size to inline. */
79 #define MLX5_TXQ_INLINE_MIN "txq_inline_min"
81 /* Device parameter to limit packet size to inline with Enhanced MPW. */
82 #define MLX5_TXQ_INLINE_MPW "txq_inline_mpw"
85 * Device parameter to configure the number of TX queues threshold for
86 * enabling inline send.
88 #define MLX5_TXQS_MIN_INLINE "txqs_min_inline"
91 * Device parameter to configure the number of TX queues threshold for
92 * enabling vectorized Tx, deprecated, ignored (no vectorized Tx routines).
94 #define MLX5_TXQS_MAX_VEC "txqs_max_vec"
96 /* Device parameter to enable multi-packet send WQEs. */
97 #define MLX5_TXQ_MPW_EN "txq_mpw_en"
100 * Device parameter to include 2 dsegs in the title WQEBB.
101 * Deprecated, ignored.
103 #define MLX5_TXQ_MPW_HDR_DSEG_EN "txq_mpw_hdr_dseg_en"
106 * Device parameter to limit the size of inlining packet.
107 * Deprecated, ignored.
109 #define MLX5_TXQ_MAX_INLINE_LEN "txq_max_inline_len"
112 * Device parameter to enable hardware Tx vector.
113 * Deprecated, ignored (no vectorized Tx routines anymore).
115 #define MLX5_TX_VEC_EN "tx_vec_en"
117 /* Device parameter to enable hardware Rx vector. */
118 #define MLX5_RX_VEC_EN "rx_vec_en"
120 /* Allow L3 VXLAN flow creation. */
121 #define MLX5_L3_VXLAN_EN "l3_vxlan_en"
123 /* Activate DV E-Switch flow steering. */
124 #define MLX5_DV_ESW_EN "dv_esw_en"
126 /* Activate DV flow steering. */
127 #define MLX5_DV_FLOW_EN "dv_flow_en"
129 /* Activate Netlink support in VF mode. */
130 #define MLX5_VF_NL_EN "vf_nl_en"
132 /* Enable extending memsegs when creating a MR. */
133 #define MLX5_MR_EXT_MEMSEG_EN "mr_ext_memseg_en"
135 /* Select port representors to instantiate. */
136 #define MLX5_REPRESENTOR "representor"
138 /* Device parameter to configure the maximum number of dump files per queue. */
139 #define MLX5_MAX_DUMP_FILES_NUM "max_dump_files_num"
141 /* Configure timeout of LRO session (in microseconds). */
142 #define MLX5_LRO_TIMEOUT_USEC "lro_timeout_usec"
144 #ifndef HAVE_IBV_MLX5_MOD_MPW
145 #define MLX5DV_CONTEXT_FLAGS_MPW_ALLOWED (1 << 2)
146 #define MLX5DV_CONTEXT_FLAGS_ENHANCED_MPW (1 << 3)
149 #ifndef HAVE_IBV_MLX5_MOD_CQE_128B_COMP
150 #define MLX5DV_CONTEXT_FLAGS_CQE_128B_COMP (1 << 4)
153 static const char *MZ_MLX5_PMD_SHARED_DATA = "mlx5_pmd_shared_data";
155 /* Shared memory between primary and secondary processes. */
156 struct mlx5_shared_data *mlx5_shared_data;
158 /* Spinlock for mlx5_shared_data allocation. */
159 static rte_spinlock_t mlx5_shared_data_lock = RTE_SPINLOCK_INITIALIZER;
161 /* Process local data for secondary processes. */
162 static struct mlx5_local_data mlx5_local_data;
164 /** Driver-specific log messages type. */
167 /** Data associated with devices to spawn. */
168 struct mlx5_dev_spawn_data {
169 uint32_t ifindex; /**< Network interface index. */
170 uint32_t max_port; /**< IB device maximal port index. */
171 uint32_t ibv_port; /**< IB device physical port index. */
172 struct mlx5_switch_info info; /**< Switch information. */
173 struct ibv_device *ibv_dev; /**< Associated IB device. */
174 struct rte_eth_dev *eth_dev; /**< Associated Ethernet device. */
175 struct rte_pci_device *pci_dev; /**< Backend PCI device. */
178 static LIST_HEAD(, mlx5_ibv_shared) mlx5_ibv_list = LIST_HEAD_INITIALIZER();
179 static pthread_mutex_t mlx5_ibv_list_mutex = PTHREAD_MUTEX_INITIALIZER;
182 * Initialize the counters management structure.
185 * Pointer to mlx5_ibv_shared object to free
188 mlx5_flow_counters_mng_init(struct mlx5_ibv_shared *sh)
192 TAILQ_INIT(&sh->cmng.flow_counters);
193 for (i = 0; i < RTE_DIM(sh->cmng.ccont); ++i)
194 TAILQ_INIT(&sh->cmng.ccont[i].pool_list);
198 * Destroy all the resources allocated for a counter memory management.
201 * Pointer to the memory management structure.
204 mlx5_flow_destroy_counter_stat_mem_mng(struct mlx5_counter_stats_mem_mng *mng)
206 uint8_t *mem = (uint8_t *)(uintptr_t)mng->raws[0].data;
208 LIST_REMOVE(mng, next);
209 claim_zero(mlx5_devx_cmd_destroy(mng->dm));
210 claim_zero(mlx5_glue->devx_umem_dereg(mng->umem));
215 * Close and release all the resources of the counters management.
218 * Pointer to mlx5_ibv_shared object to free.
221 mlx5_flow_counters_mng_close(struct mlx5_ibv_shared *sh)
223 struct mlx5_counter_stats_mem_mng *mng;
230 rte_eal_alarm_cancel(mlx5_flow_query_alarm, sh);
231 if (rte_errno != EINPROGRESS)
235 for (i = 0; i < RTE_DIM(sh->cmng.ccont); ++i) {
236 struct mlx5_flow_counter_pool *pool;
237 uint32_t batch = !!(i % 2);
239 if (!sh->cmng.ccont[i].pools)
241 pool = TAILQ_FIRST(&sh->cmng.ccont[i].pool_list);
246 (mlx5_devx_cmd_destroy(pool->min_dcs));
248 for (j = 0; j < MLX5_COUNTERS_PER_POOL; ++j) {
249 if (pool->counters_raw[j].action)
251 (mlx5_glue->destroy_flow_action
252 (pool->counters_raw[j].action));
253 if (!batch && pool->counters_raw[j].dcs)
254 claim_zero(mlx5_devx_cmd_destroy
255 (pool->counters_raw[j].dcs));
257 TAILQ_REMOVE(&sh->cmng.ccont[i].pool_list, pool,
260 pool = TAILQ_FIRST(&sh->cmng.ccont[i].pool_list);
262 rte_free(sh->cmng.ccont[i].pools);
264 mng = LIST_FIRST(&sh->cmng.mem_mngs);
266 mlx5_flow_destroy_counter_stat_mem_mng(mng);
267 mng = LIST_FIRST(&sh->cmng.mem_mngs);
269 memset(&sh->cmng, 0, sizeof(sh->cmng));
273 * Extract pdn of PD object using DV API.
276 * Pointer to the verbs PD object.
278 * Pointer to the PD object number variable.
281 * 0 on success, error value otherwise.
283 #ifdef HAVE_IBV_FLOW_DV_SUPPORT
285 mlx5_get_pdn(struct ibv_pd *pd __rte_unused, uint32_t *pdn __rte_unused)
287 struct mlx5dv_obj obj;
288 struct mlx5dv_pd pd_info;
292 obj.pd.out = &pd_info;
293 ret = mlx5_glue->dv_init_obj(&obj, MLX5DV_OBJ_PD);
295 DRV_LOG(DEBUG, "Fail to get PD object info");
301 #endif /* HAVE_IBV_FLOW_DV_SUPPORT */
304 * Allocate shared IB device context. If there is multiport device the
305 * master and representors will share this context, if there is single
306 * port dedicated IB device, the context will be used by only given
307 * port due to unification.
309 * Routine first searches the context for the specified IB device name,
310 * if found the shared context assumed and reference counter is incremented.
311 * If no context found the new one is created and initialized with specified
312 * IB device context and parameters.
315 * Pointer to the IB device attributes (name, port, etc).
318 * Pointer to mlx5_ibv_shared object on success,
319 * otherwise NULL and rte_errno is set.
321 static struct mlx5_ibv_shared *
322 mlx5_alloc_shared_ibctx(const struct mlx5_dev_spawn_data *spawn)
324 struct mlx5_ibv_shared *sh;
329 /* Secondary process should not create the shared context. */
330 assert(rte_eal_process_type() == RTE_PROC_PRIMARY);
331 pthread_mutex_lock(&mlx5_ibv_list_mutex);
332 /* Search for IB context by device name. */
333 LIST_FOREACH(sh, &mlx5_ibv_list, next) {
334 if (!strcmp(sh->ibdev_name, spawn->ibv_dev->name)) {
339 /* No device found, we have to create new shared context. */
340 assert(spawn->max_port);
341 sh = rte_zmalloc("ethdev shared ib context",
342 sizeof(struct mlx5_ibv_shared) +
344 sizeof(struct mlx5_ibv_shared_port),
345 RTE_CACHE_LINE_SIZE);
347 DRV_LOG(ERR, "shared context allocation failure");
351 /* Try to open IB device with DV first, then usual Verbs. */
353 sh->ctx = mlx5_glue->dv_open_device(spawn->ibv_dev);
356 DRV_LOG(DEBUG, "DevX is supported");
358 sh->ctx = mlx5_glue->open_device(spawn->ibv_dev);
360 err = errno ? errno : ENODEV;
363 DRV_LOG(DEBUG, "DevX is NOT supported");
365 err = mlx5_glue->query_device_ex(sh->ctx, NULL, &sh->device_attr);
367 DRV_LOG(DEBUG, "ibv_query_device_ex() failed");
371 sh->max_port = spawn->max_port;
372 strncpy(sh->ibdev_name, sh->ctx->device->name,
373 sizeof(sh->ibdev_name));
374 strncpy(sh->ibdev_path, sh->ctx->device->ibdev_path,
375 sizeof(sh->ibdev_path));
376 sh->pci_dev = spawn->pci_dev;
377 pthread_mutex_init(&sh->intr_mutex, NULL);
379 * Setting port_id to max unallowed value means
380 * there is no interrupt subhandler installed for
381 * the given port index i.
383 for (i = 0; i < sh->max_port; i++)
384 sh->port[i].ih_port_id = RTE_MAX_ETHPORTS;
385 sh->pd = mlx5_glue->alloc_pd(sh->ctx);
386 if (sh->pd == NULL) {
387 DRV_LOG(ERR, "PD allocation failure");
391 #ifdef HAVE_IBV_FLOW_DV_SUPPORT
392 err = mlx5_get_pdn(sh->pd, &sh->pdn);
394 DRV_LOG(ERR, "Fail to extract pdn from PD");
397 #endif /* HAVE_IBV_FLOW_DV_SUPPORT */
399 * Once the device is added to the list of memory event
400 * callback, its global MR cache table cannot be expanded
401 * on the fly because of deadlock. If it overflows, lookup
402 * should be done by searching MR list linearly, which is slow.
404 * At this point the device is not added to the memory
405 * event list yet, context is just being created.
407 err = mlx5_mr_btree_init(&sh->mr.cache,
408 MLX5_MR_BTREE_CACHE_N * 2,
409 sh->pci_dev->device.numa_node);
414 mlx5_flow_counters_mng_init(sh);
415 LIST_INSERT_HEAD(&mlx5_ibv_list, sh, next);
417 pthread_mutex_unlock(&mlx5_ibv_list_mutex);
420 pthread_mutex_unlock(&mlx5_ibv_list_mutex);
423 claim_zero(mlx5_glue->dealloc_pd(sh->pd));
425 claim_zero(mlx5_glue->close_device(sh->ctx));
433 * Free shared IB device context. Decrement counter and if zero free
434 * all allocated resources and close handles.
437 * Pointer to mlx5_ibv_shared object to free
440 mlx5_free_shared_ibctx(struct mlx5_ibv_shared *sh)
442 pthread_mutex_lock(&mlx5_ibv_list_mutex);
444 /* Check the object presence in the list. */
445 struct mlx5_ibv_shared *lctx;
447 LIST_FOREACH(lctx, &mlx5_ibv_list, next)
452 DRV_LOG(ERR, "Freeing non-existing shared IB context");
458 /* Secondary process should not free the shared context. */
459 assert(rte_eal_process_type() == RTE_PROC_PRIMARY);
462 /* Release created Memory Regions. */
464 LIST_REMOVE(sh, next);
466 * Ensure there is no async event handler installed.
467 * Only primary process handles async device events.
469 mlx5_flow_counters_mng_close(sh);
470 assert(!sh->intr_cnt);
472 mlx5_intr_callback_unregister
473 (&sh->intr_handle, mlx5_dev_interrupt_handler, sh);
474 pthread_mutex_destroy(&sh->intr_mutex);
476 claim_zero(mlx5_glue->dealloc_pd(sh->pd));
478 claim_zero(mlx5_glue->close_device(sh->ctx));
481 pthread_mutex_unlock(&mlx5_ibv_list_mutex);
485 * Initialize DR related data within private structure.
486 * Routine checks the reference counter and does actual
487 * resources creation/initialization only if counter is zero.
490 * Pointer to the private device data structure.
493 * Zero on success, positive error code otherwise.
496 mlx5_alloc_shared_dr(struct mlx5_priv *priv)
498 #ifdef HAVE_MLX5DV_DR
499 struct mlx5_ibv_shared *sh = priv->sh;
505 /* Shared DV/DR structures is already initialized. */
510 /* Reference counter is zero, we should initialize structures. */
511 domain = mlx5_glue->dr_create_domain(sh->ctx,
512 MLX5DV_DR_DOMAIN_TYPE_NIC_RX);
514 DRV_LOG(ERR, "ingress mlx5dv_dr_create_domain failed");
518 sh->rx_domain = domain;
519 domain = mlx5_glue->dr_create_domain(sh->ctx,
520 MLX5DV_DR_DOMAIN_TYPE_NIC_TX);
522 DRV_LOG(ERR, "egress mlx5dv_dr_create_domain failed");
526 pthread_mutex_init(&sh->dv_mutex, NULL);
527 sh->tx_domain = domain;
528 #ifdef HAVE_MLX5DV_DR_ESWITCH
529 if (priv->config.dv_esw_en) {
530 domain = mlx5_glue->dr_create_domain
531 (sh->ctx, MLX5DV_DR_DOMAIN_TYPE_FDB);
533 DRV_LOG(ERR, "FDB mlx5dv_dr_create_domain failed");
537 sh->fdb_domain = domain;
538 sh->esw_drop_action = mlx5_glue->dr_create_flow_action_drop();
546 /* Rollback the created objects. */
548 mlx5_glue->dr_destroy_domain(sh->rx_domain);
549 sh->rx_domain = NULL;
552 mlx5_glue->dr_destroy_domain(sh->tx_domain);
553 sh->tx_domain = NULL;
555 if (sh->fdb_domain) {
556 mlx5_glue->dr_destroy_domain(sh->fdb_domain);
557 sh->fdb_domain = NULL;
559 if (sh->esw_drop_action) {
560 mlx5_glue->destroy_flow_action(sh->esw_drop_action);
561 sh->esw_drop_action = NULL;
571 * Destroy DR related data within private structure.
574 * Pointer to the private device data structure.
577 mlx5_free_shared_dr(struct mlx5_priv *priv)
579 #ifdef HAVE_MLX5DV_DR
580 struct mlx5_ibv_shared *sh;
582 if (!priv->dr_shared)
587 assert(sh->dv_refcnt);
588 if (sh->dv_refcnt && --sh->dv_refcnt)
591 mlx5_glue->dr_destroy_domain(sh->rx_domain);
592 sh->rx_domain = NULL;
595 mlx5_glue->dr_destroy_domain(sh->tx_domain);
596 sh->tx_domain = NULL;
598 #ifdef HAVE_MLX5DV_DR_ESWITCH
599 if (sh->fdb_domain) {
600 mlx5_glue->dr_destroy_domain(sh->fdb_domain);
601 sh->fdb_domain = NULL;
603 if (sh->esw_drop_action) {
604 mlx5_glue->destroy_flow_action(sh->esw_drop_action);
605 sh->esw_drop_action = NULL;
608 pthread_mutex_destroy(&sh->dv_mutex);
615 * Initialize shared data between primary and secondary process.
617 * A memzone is reserved by primary process and secondary processes attach to
621 * 0 on success, a negative errno value otherwise and rte_errno is set.
624 mlx5_init_shared_data(void)
626 const struct rte_memzone *mz;
629 rte_spinlock_lock(&mlx5_shared_data_lock);
630 if (mlx5_shared_data == NULL) {
631 if (rte_eal_process_type() == RTE_PROC_PRIMARY) {
632 /* Allocate shared memory. */
633 mz = rte_memzone_reserve(MZ_MLX5_PMD_SHARED_DATA,
634 sizeof(*mlx5_shared_data),
638 "Cannot allocate mlx5 shared data\n");
642 mlx5_shared_data = mz->addr;
643 memset(mlx5_shared_data, 0, sizeof(*mlx5_shared_data));
644 rte_spinlock_init(&mlx5_shared_data->lock);
646 /* Lookup allocated shared memory. */
647 mz = rte_memzone_lookup(MZ_MLX5_PMD_SHARED_DATA);
650 "Cannot attach mlx5 shared data\n");
654 mlx5_shared_data = mz->addr;
655 memset(&mlx5_local_data, 0, sizeof(mlx5_local_data));
659 rte_spinlock_unlock(&mlx5_shared_data_lock);
664 * Retrieve integer value from environment variable.
667 * Environment variable name.
670 * Integer value, 0 if the variable is not set.
673 mlx5_getenv_int(const char *name)
675 const char *val = getenv(name);
683 * Verbs callback to allocate a memory. This function should allocate the space
684 * according to the size provided residing inside a huge page.
685 * Please note that all allocation must respect the alignment from libmlx5
686 * (i.e. currently sysconf(_SC_PAGESIZE)).
689 * The size in bytes of the memory to allocate.
691 * A pointer to the callback data.
694 * Allocated buffer, NULL otherwise and rte_errno is set.
697 mlx5_alloc_verbs_buf(size_t size, void *data)
699 struct mlx5_priv *priv = data;
701 size_t alignment = sysconf(_SC_PAGESIZE);
702 unsigned int socket = SOCKET_ID_ANY;
704 if (priv->verbs_alloc_ctx.type == MLX5_VERBS_ALLOC_TYPE_TX_QUEUE) {
705 const struct mlx5_txq_ctrl *ctrl = priv->verbs_alloc_ctx.obj;
707 socket = ctrl->socket;
708 } else if (priv->verbs_alloc_ctx.type ==
709 MLX5_VERBS_ALLOC_TYPE_RX_QUEUE) {
710 const struct mlx5_rxq_ctrl *ctrl = priv->verbs_alloc_ctx.obj;
712 socket = ctrl->socket;
714 assert(data != NULL);
715 ret = rte_malloc_socket(__func__, size, alignment, socket);
722 * Verbs callback to free a memory.
725 * A pointer to the memory to free.
727 * A pointer to the callback data.
730 mlx5_free_verbs_buf(void *ptr, void *data __rte_unused)
732 assert(data != NULL);
737 * Initialize process private data structure.
740 * Pointer to Ethernet device structure.
743 * 0 on success, a negative errno value otherwise and rte_errno is set.
746 mlx5_proc_priv_init(struct rte_eth_dev *dev)
748 struct mlx5_priv *priv = dev->data->dev_private;
749 struct mlx5_proc_priv *ppriv;
753 * UAR register table follows the process private structure. BlueFlame
754 * registers for Tx queues are stored in the table.
757 sizeof(struct mlx5_proc_priv) + priv->txqs_n * sizeof(void *);
758 ppriv = rte_malloc_socket("mlx5_proc_priv", ppriv_size,
759 RTE_CACHE_LINE_SIZE, dev->device->numa_node);
764 ppriv->uar_table_sz = ppriv_size;
765 dev->process_private = ppriv;
770 * Un-initialize process private data structure.
773 * Pointer to Ethernet device structure.
776 mlx5_proc_priv_uninit(struct rte_eth_dev *dev)
778 if (!dev->process_private)
780 rte_free(dev->process_private);
781 dev->process_private = NULL;
785 * DPDK callback to close the device.
787 * Destroy all queues and objects, free memory.
790 * Pointer to Ethernet device structure.
793 mlx5_dev_close(struct rte_eth_dev *dev)
795 struct mlx5_priv *priv = dev->data->dev_private;
799 DRV_LOG(DEBUG, "port %u closing device \"%s\"",
801 ((priv->sh->ctx != NULL) ? priv->sh->ctx->device->name : ""));
802 /* In case mlx5_dev_stop() has not been called. */
803 mlx5_dev_interrupt_handler_uninstall(dev);
804 mlx5_traffic_disable(dev);
805 mlx5_flow_flush(dev, NULL);
806 /* Prevent crashes when queues are still in use. */
807 dev->rx_pkt_burst = removed_rx_burst;
808 dev->tx_pkt_burst = removed_tx_burst;
810 /* Disable datapath on secondary process. */
811 mlx5_mp_req_stop_rxtx(dev);
812 if (priv->rxqs != NULL) {
813 /* XXX race condition if mlx5_rx_burst() is still running. */
815 for (i = 0; (i != priv->rxqs_n); ++i)
816 mlx5_rxq_release(dev, i);
820 if (priv->txqs != NULL) {
821 /* XXX race condition if mlx5_tx_burst() is still running. */
823 for (i = 0; (i != priv->txqs_n); ++i)
824 mlx5_txq_release(dev, i);
828 mlx5_proc_priv_uninit(dev);
829 mlx5_mprq_free_mp(dev);
830 /* Remove from memory callback device list. */
831 rte_rwlock_write_lock(&mlx5_shared_data->mem_event_rwlock);
833 LIST_REMOVE(priv->sh, mem_event_cb);
834 rte_rwlock_write_unlock(&mlx5_shared_data->mem_event_rwlock);
835 mlx5_free_shared_dr(priv);
836 if (priv->rss_conf.rss_key != NULL)
837 rte_free(priv->rss_conf.rss_key);
838 if (priv->reta_idx != NULL)
839 rte_free(priv->reta_idx);
841 mlx5_nl_mac_addr_flush(dev);
842 if (priv->nl_socket_route >= 0)
843 close(priv->nl_socket_route);
844 if (priv->nl_socket_rdma >= 0)
845 close(priv->nl_socket_rdma);
848 * Free the shared context in last turn, because the cleanup
849 * routines above may use some shared fields, like
850 * mlx5_nl_mac_addr_flush() uses ibdev_path for retrieveing
851 * ifindex if Netlink fails.
853 mlx5_free_shared_ibctx(priv->sh);
856 ret = mlx5_hrxq_verify(dev);
858 DRV_LOG(WARNING, "port %u some hash Rx queue still remain",
860 ret = mlx5_ind_table_obj_verify(dev);
862 DRV_LOG(WARNING, "port %u some indirection table still remain",
864 ret = mlx5_rxq_obj_verify(dev);
866 DRV_LOG(WARNING, "port %u some Rx queue objects still remain",
868 ret = mlx5_rxq_verify(dev);
870 DRV_LOG(WARNING, "port %u some Rx queues still remain",
872 ret = mlx5_txq_ibv_verify(dev);
874 DRV_LOG(WARNING, "port %u some Verbs Tx queue still remain",
876 ret = mlx5_txq_verify(dev);
878 DRV_LOG(WARNING, "port %u some Tx queues still remain",
880 ret = mlx5_flow_verify(dev);
882 DRV_LOG(WARNING, "port %u some flows still remain",
884 if (priv->domain_id != RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID) {
888 RTE_ETH_FOREACH_DEV_OF(port_id, dev->device) {
889 struct mlx5_priv *opriv =
890 rte_eth_devices[port_id].data->dev_private;
893 opriv->domain_id != priv->domain_id ||
894 &rte_eth_devices[port_id] == dev)
899 claim_zero(rte_eth_switch_domain_free(priv->domain_id));
901 memset(priv, 0, sizeof(*priv));
902 priv->domain_id = RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID;
904 * Reset mac_addrs to NULL such that it is not freed as part of
905 * rte_eth_dev_release_port(). mac_addrs is part of dev_private so
906 * it is freed when dev_private is freed.
908 dev->data->mac_addrs = NULL;
911 const struct eth_dev_ops mlx5_dev_ops = {
912 .dev_configure = mlx5_dev_configure,
913 .dev_start = mlx5_dev_start,
914 .dev_stop = mlx5_dev_stop,
915 .dev_set_link_down = mlx5_set_link_down,
916 .dev_set_link_up = mlx5_set_link_up,
917 .dev_close = mlx5_dev_close,
918 .promiscuous_enable = mlx5_promiscuous_enable,
919 .promiscuous_disable = mlx5_promiscuous_disable,
920 .allmulticast_enable = mlx5_allmulticast_enable,
921 .allmulticast_disable = mlx5_allmulticast_disable,
922 .link_update = mlx5_link_update,
923 .stats_get = mlx5_stats_get,
924 .stats_reset = mlx5_stats_reset,
925 .xstats_get = mlx5_xstats_get,
926 .xstats_reset = mlx5_xstats_reset,
927 .xstats_get_names = mlx5_xstats_get_names,
928 .fw_version_get = mlx5_fw_version_get,
929 .dev_infos_get = mlx5_dev_infos_get,
930 .read_clock = mlx5_read_clock,
931 .dev_supported_ptypes_get = mlx5_dev_supported_ptypes_get,
932 .vlan_filter_set = mlx5_vlan_filter_set,
933 .rx_queue_setup = mlx5_rx_queue_setup,
934 .tx_queue_setup = mlx5_tx_queue_setup,
935 .rx_queue_release = mlx5_rx_queue_release,
936 .tx_queue_release = mlx5_tx_queue_release,
937 .flow_ctrl_get = mlx5_dev_get_flow_ctrl,
938 .flow_ctrl_set = mlx5_dev_set_flow_ctrl,
939 .mac_addr_remove = mlx5_mac_addr_remove,
940 .mac_addr_add = mlx5_mac_addr_add,
941 .mac_addr_set = mlx5_mac_addr_set,
942 .set_mc_addr_list = mlx5_set_mc_addr_list,
943 .mtu_set = mlx5_dev_set_mtu,
944 .vlan_strip_queue_set = mlx5_vlan_strip_queue_set,
945 .vlan_offload_set = mlx5_vlan_offload_set,
946 .reta_update = mlx5_dev_rss_reta_update,
947 .reta_query = mlx5_dev_rss_reta_query,
948 .rss_hash_update = mlx5_rss_hash_update,
949 .rss_hash_conf_get = mlx5_rss_hash_conf_get,
950 .filter_ctrl = mlx5_dev_filter_ctrl,
951 .rx_descriptor_status = mlx5_rx_descriptor_status,
952 .tx_descriptor_status = mlx5_tx_descriptor_status,
953 .rx_queue_count = mlx5_rx_queue_count,
954 .rx_queue_intr_enable = mlx5_rx_intr_enable,
955 .rx_queue_intr_disable = mlx5_rx_intr_disable,
956 .is_removed = mlx5_is_removed,
959 /* Available operations from secondary process. */
960 static const struct eth_dev_ops mlx5_dev_sec_ops = {
961 .stats_get = mlx5_stats_get,
962 .stats_reset = mlx5_stats_reset,
963 .xstats_get = mlx5_xstats_get,
964 .xstats_reset = mlx5_xstats_reset,
965 .xstats_get_names = mlx5_xstats_get_names,
966 .fw_version_get = mlx5_fw_version_get,
967 .dev_infos_get = mlx5_dev_infos_get,
968 .rx_descriptor_status = mlx5_rx_descriptor_status,
969 .tx_descriptor_status = mlx5_tx_descriptor_status,
972 /* Available operations in flow isolated mode. */
973 const struct eth_dev_ops mlx5_dev_ops_isolate = {
974 .dev_configure = mlx5_dev_configure,
975 .dev_start = mlx5_dev_start,
976 .dev_stop = mlx5_dev_stop,
977 .dev_set_link_down = mlx5_set_link_down,
978 .dev_set_link_up = mlx5_set_link_up,
979 .dev_close = mlx5_dev_close,
980 .promiscuous_enable = mlx5_promiscuous_enable,
981 .promiscuous_disable = mlx5_promiscuous_disable,
982 .allmulticast_enable = mlx5_allmulticast_enable,
983 .allmulticast_disable = mlx5_allmulticast_disable,
984 .link_update = mlx5_link_update,
985 .stats_get = mlx5_stats_get,
986 .stats_reset = mlx5_stats_reset,
987 .xstats_get = mlx5_xstats_get,
988 .xstats_reset = mlx5_xstats_reset,
989 .xstats_get_names = mlx5_xstats_get_names,
990 .fw_version_get = mlx5_fw_version_get,
991 .dev_infos_get = mlx5_dev_infos_get,
992 .dev_supported_ptypes_get = mlx5_dev_supported_ptypes_get,
993 .vlan_filter_set = mlx5_vlan_filter_set,
994 .rx_queue_setup = mlx5_rx_queue_setup,
995 .tx_queue_setup = mlx5_tx_queue_setup,
996 .rx_queue_release = mlx5_rx_queue_release,
997 .tx_queue_release = mlx5_tx_queue_release,
998 .flow_ctrl_get = mlx5_dev_get_flow_ctrl,
999 .flow_ctrl_set = mlx5_dev_set_flow_ctrl,
1000 .mac_addr_remove = mlx5_mac_addr_remove,
1001 .mac_addr_add = mlx5_mac_addr_add,
1002 .mac_addr_set = mlx5_mac_addr_set,
1003 .set_mc_addr_list = mlx5_set_mc_addr_list,
1004 .mtu_set = mlx5_dev_set_mtu,
1005 .vlan_strip_queue_set = mlx5_vlan_strip_queue_set,
1006 .vlan_offload_set = mlx5_vlan_offload_set,
1007 .filter_ctrl = mlx5_dev_filter_ctrl,
1008 .rx_descriptor_status = mlx5_rx_descriptor_status,
1009 .tx_descriptor_status = mlx5_tx_descriptor_status,
1010 .rx_queue_intr_enable = mlx5_rx_intr_enable,
1011 .rx_queue_intr_disable = mlx5_rx_intr_disable,
1012 .is_removed = mlx5_is_removed,
1016 * Verify and store value for device argument.
1019 * Key argument to verify.
1021 * Value associated with key.
1026 * 0 on success, a negative errno value otherwise and rte_errno is set.
1029 mlx5_args_check(const char *key, const char *val, void *opaque)
1031 struct mlx5_dev_config *config = opaque;
1034 /* No-op, port representors are processed in mlx5_dev_spawn(). */
1035 if (!strcmp(MLX5_REPRESENTOR, key))
1038 tmp = strtoul(val, NULL, 0);
1041 DRV_LOG(WARNING, "%s: \"%s\" is not a valid integer", key, val);
1044 if (strcmp(MLX5_RXQ_CQE_COMP_EN, key) == 0) {
1045 config->cqe_comp = !!tmp;
1046 } else if (strcmp(MLX5_RXQ_CQE_PAD_EN, key) == 0) {
1047 config->cqe_pad = !!tmp;
1048 } else if (strcmp(MLX5_RXQ_PKT_PAD_EN, key) == 0) {
1049 config->hw_padding = !!tmp;
1050 } else if (strcmp(MLX5_RX_MPRQ_EN, key) == 0) {
1051 config->mprq.enabled = !!tmp;
1052 } else if (strcmp(MLX5_RX_MPRQ_LOG_STRIDE_NUM, key) == 0) {
1053 config->mprq.stride_num_n = tmp;
1054 } else if (strcmp(MLX5_RX_MPRQ_MAX_MEMCPY_LEN, key) == 0) {
1055 config->mprq.max_memcpy_len = tmp;
1056 } else if (strcmp(MLX5_RXQS_MIN_MPRQ, key) == 0) {
1057 config->mprq.min_rxqs_num = tmp;
1058 } else if (strcmp(MLX5_TXQ_INLINE, key) == 0) {
1059 DRV_LOG(WARNING, "%s: deprecated parameter,"
1060 " converted to txq_inline_max", key);
1061 config->txq_inline_max = tmp;
1062 } else if (strcmp(MLX5_TXQ_INLINE_MAX, key) == 0) {
1063 config->txq_inline_max = tmp;
1064 } else if (strcmp(MLX5_TXQ_INLINE_MIN, key) == 0) {
1065 config->txq_inline_min = tmp;
1066 } else if (strcmp(MLX5_TXQ_INLINE_MPW, key) == 0) {
1067 config->txq_inline_mpw = tmp;
1068 } else if (strcmp(MLX5_TXQS_MIN_INLINE, key) == 0) {
1069 config->txqs_inline = tmp;
1070 } else if (strcmp(MLX5_TXQS_MAX_VEC, key) == 0) {
1071 DRV_LOG(WARNING, "%s: deprecated parameter, ignored", key);
1072 } else if (strcmp(MLX5_TXQ_MPW_EN, key) == 0) {
1073 config->mps = !!tmp;
1074 } else if (strcmp(MLX5_TXQ_MPW_HDR_DSEG_EN, key) == 0) {
1075 DRV_LOG(WARNING, "%s: deprecated parameter, ignored", key);
1076 } else if (strcmp(MLX5_TXQ_MAX_INLINE_LEN, key) == 0) {
1077 DRV_LOG(WARNING, "%s: deprecated parameter,"
1078 " converted to txq_inline_mpw", key);
1079 config->txq_inline_mpw = tmp;
1080 } else if (strcmp(MLX5_TX_VEC_EN, key) == 0) {
1081 DRV_LOG(WARNING, "%s: deprecated parameter, ignored", key);
1082 } else if (strcmp(MLX5_RX_VEC_EN, key) == 0) {
1083 config->rx_vec_en = !!tmp;
1084 } else if (strcmp(MLX5_L3_VXLAN_EN, key) == 0) {
1085 config->l3_vxlan_en = !!tmp;
1086 } else if (strcmp(MLX5_VF_NL_EN, key) == 0) {
1087 config->vf_nl_en = !!tmp;
1088 } else if (strcmp(MLX5_DV_ESW_EN, key) == 0) {
1089 config->dv_esw_en = !!tmp;
1090 } else if (strcmp(MLX5_DV_FLOW_EN, key) == 0) {
1091 config->dv_flow_en = !!tmp;
1092 } else if (strcmp(MLX5_MR_EXT_MEMSEG_EN, key) == 0) {
1093 config->mr_ext_memseg_en = !!tmp;
1094 } else if (strcmp(MLX5_MAX_DUMP_FILES_NUM, key) == 0) {
1095 config->max_dump_files_num = tmp;
1096 } else if (strcmp(MLX5_LRO_TIMEOUT_USEC, key) == 0) {
1097 config->lro.timeout = tmp;
1099 DRV_LOG(WARNING, "%s: unknown parameter", key);
1107 * Parse device parameters.
1110 * Pointer to device configuration structure.
1112 * Device arguments structure.
1115 * 0 on success, a negative errno value otherwise and rte_errno is set.
1118 mlx5_args(struct mlx5_dev_config *config, struct rte_devargs *devargs)
1120 const char **params = (const char *[]){
1121 MLX5_RXQ_CQE_COMP_EN,
1122 MLX5_RXQ_CQE_PAD_EN,
1123 MLX5_RXQ_PKT_PAD_EN,
1125 MLX5_RX_MPRQ_LOG_STRIDE_NUM,
1126 MLX5_RX_MPRQ_MAX_MEMCPY_LEN,
1129 MLX5_TXQ_INLINE_MIN,
1130 MLX5_TXQ_INLINE_MAX,
1131 MLX5_TXQ_INLINE_MPW,
1132 MLX5_TXQS_MIN_INLINE,
1135 MLX5_TXQ_MPW_HDR_DSEG_EN,
1136 MLX5_TXQ_MAX_INLINE_LEN,
1143 MLX5_MR_EXT_MEMSEG_EN,
1145 MLX5_MAX_DUMP_FILES_NUM,
1146 MLX5_LRO_TIMEOUT_USEC,
1149 struct rte_kvargs *kvlist;
1153 if (devargs == NULL)
1155 /* Following UGLY cast is done to pass checkpatch. */
1156 kvlist = rte_kvargs_parse(devargs->args, params);
1157 if (kvlist == NULL) {
1161 /* Process parameters. */
1162 for (i = 0; (params[i] != NULL); ++i) {
1163 if (rte_kvargs_count(kvlist, params[i])) {
1164 ret = rte_kvargs_process(kvlist, params[i],
1165 mlx5_args_check, config);
1168 rte_kvargs_free(kvlist);
1173 rte_kvargs_free(kvlist);
1177 static struct rte_pci_driver mlx5_driver;
1180 * PMD global initialization.
1182 * Independent from individual device, this function initializes global
1183 * per-PMD data structures distinguishing primary and secondary processes.
1184 * Hence, each initialization is called once per a process.
1187 * 0 on success, a negative errno value otherwise and rte_errno is set.
1190 mlx5_init_once(void)
1192 struct mlx5_shared_data *sd;
1193 struct mlx5_local_data *ld = &mlx5_local_data;
1196 if (mlx5_init_shared_data())
1198 sd = mlx5_shared_data;
1200 rte_spinlock_lock(&sd->lock);
1201 switch (rte_eal_process_type()) {
1202 case RTE_PROC_PRIMARY:
1205 LIST_INIT(&sd->mem_event_cb_list);
1206 rte_rwlock_init(&sd->mem_event_rwlock);
1207 rte_mem_event_callback_register("MLX5_MEM_EVENT_CB",
1208 mlx5_mr_mem_event_cb, NULL);
1209 ret = mlx5_mp_init_primary();
1212 sd->init_done = true;
1214 case RTE_PROC_SECONDARY:
1217 ret = mlx5_mp_init_secondary();
1220 ++sd->secondary_cnt;
1221 ld->init_done = true;
1227 rte_spinlock_unlock(&sd->lock);
1232 * Configures the minimal amount of data to inline into WQE
1233 * while sending packets.
1235 * - the txq_inline_min has the maximal priority, if this
1236 * key is specified in devargs
1237 * - if DevX is enabled the inline mode is queried from the
1238 * device (HCA attributes and NIC vport context if needed).
1239 * - otherwise L2 mode (18 bytes) is assumed for ConnectX-4/4LX
1240 * and none (0 bytes) for other NICs
1243 * Verbs device parameters (name, port, switch_info) to spawn.
1245 * Device configuration parameters.
1248 mlx5_set_min_inline(struct mlx5_dev_spawn_data *spawn,
1249 struct mlx5_dev_config *config)
1251 if (config->txq_inline_min != MLX5_ARG_UNSET) {
1252 /* Application defines size of inlined data explicitly. */
1253 switch (spawn->pci_dev->id.device_id) {
1254 case PCI_DEVICE_ID_MELLANOX_CONNECTX4:
1255 case PCI_DEVICE_ID_MELLANOX_CONNECTX4VF:
1256 case PCI_DEVICE_ID_MELLANOX_CONNECTX4LX:
1257 case PCI_DEVICE_ID_MELLANOX_CONNECTX4LXVF:
1258 if (config->txq_inline_min <
1259 (int)MLX5_INLINE_HSIZE_L2) {
1261 "txq_inline_mix aligned to minimal"
1262 " ConnectX-4 required value %d",
1263 (int)MLX5_INLINE_HSIZE_L2);
1264 config->txq_inline_min = MLX5_INLINE_HSIZE_L2;
1270 if (config->hca_attr.eth_net_offloads) {
1271 /* We have DevX enabled, inline mode queried successfully. */
1272 switch (config->hca_attr.wqe_inline_mode) {
1273 case MLX5_CAP_INLINE_MODE_L2:
1274 /* outer L2 header must be inlined. */
1275 config->txq_inline_min = MLX5_INLINE_HSIZE_L2;
1277 case MLX5_CAP_INLINE_MODE_NOT_REQUIRED:
1278 /* No inline data are required by NIC. */
1279 config->txq_inline_min = MLX5_INLINE_HSIZE_NONE;
1280 config->hw_vlan_insert =
1281 config->hca_attr.wqe_vlan_insert;
1282 DRV_LOG(DEBUG, "Tx VLAN insertion is supported");
1284 case MLX5_CAP_INLINE_MODE_VPORT_CONTEXT:
1285 /* inline mode is defined by NIC vport context. */
1286 if (!config->hca_attr.eth_virt)
1288 switch (config->hca_attr.vport_inline_mode) {
1289 case MLX5_INLINE_MODE_NONE:
1290 config->txq_inline_min =
1291 MLX5_INLINE_HSIZE_NONE;
1293 case MLX5_INLINE_MODE_L2:
1294 config->txq_inline_min =
1295 MLX5_INLINE_HSIZE_L2;
1297 case MLX5_INLINE_MODE_IP:
1298 config->txq_inline_min =
1299 MLX5_INLINE_HSIZE_L3;
1301 case MLX5_INLINE_MODE_TCP_UDP:
1302 config->txq_inline_min =
1303 MLX5_INLINE_HSIZE_L4;
1305 case MLX5_INLINE_MODE_INNER_L2:
1306 config->txq_inline_min =
1307 MLX5_INLINE_HSIZE_INNER_L2;
1309 case MLX5_INLINE_MODE_INNER_IP:
1310 config->txq_inline_min =
1311 MLX5_INLINE_HSIZE_INNER_L3;
1313 case MLX5_INLINE_MODE_INNER_TCP_UDP:
1314 config->txq_inline_min =
1315 MLX5_INLINE_HSIZE_INNER_L4;
1321 * We get here if we are unable to deduce
1322 * inline data size with DevX. Try PCI ID
1323 * to determine old NICs.
1325 switch (spawn->pci_dev->id.device_id) {
1326 case PCI_DEVICE_ID_MELLANOX_CONNECTX4:
1327 case PCI_DEVICE_ID_MELLANOX_CONNECTX4VF:
1328 case PCI_DEVICE_ID_MELLANOX_CONNECTX4LX:
1329 case PCI_DEVICE_ID_MELLANOX_CONNECTX4LXVF:
1330 config->txq_inline_min = MLX5_INLINE_HSIZE_L2;
1331 config->hw_vlan_insert = 0;
1333 case PCI_DEVICE_ID_MELLANOX_CONNECTX5:
1334 case PCI_DEVICE_ID_MELLANOX_CONNECTX5VF:
1335 case PCI_DEVICE_ID_MELLANOX_CONNECTX5EX:
1336 case PCI_DEVICE_ID_MELLANOX_CONNECTX5EXVF:
1338 * These NICs support VLAN insertion from WQE and
1339 * report the wqe_vlan_insert flag. But there is the bug
1340 * and PFC control may be broken, so disable feature.
1342 config->hw_vlan_insert = 0;
1345 config->txq_inline_min = MLX5_INLINE_HSIZE_NONE;
1349 DRV_LOG(DEBUG, "min tx inline configured: %d", config->txq_inline_min);
1353 * Allocate page of door-bells and register it using DevX API.
1356 * Pointer to Ethernet device.
1359 * Pointer to new page on success, NULL otherwise.
1361 static struct mlx5_devx_dbr_page *
1362 mlx5_alloc_dbr_page(struct rte_eth_dev *dev)
1364 struct mlx5_priv *priv = dev->data->dev_private;
1365 struct mlx5_devx_dbr_page *page;
1367 /* Allocate space for door-bell page and management data. */
1368 page = rte_calloc_socket(__func__, 1, sizeof(struct mlx5_devx_dbr_page),
1369 RTE_CACHE_LINE_SIZE, dev->device->numa_node);
1371 DRV_LOG(ERR, "port %u cannot allocate dbr page",
1372 dev->data->port_id);
1375 /* Register allocated memory. */
1376 page->umem = mlx5_glue->devx_umem_reg(priv->sh->ctx, page->dbrs,
1377 MLX5_DBR_PAGE_SIZE, 0);
1379 DRV_LOG(ERR, "port %u cannot umem reg dbr page",
1380 dev->data->port_id);
1388 * Find the next available door-bell, allocate new page if needed.
1391 * Pointer to Ethernet device.
1392 * @param [out] dbr_page
1393 * Door-bell page containing the page data.
1396 * Door-bell address offset on success, a negative error value otherwise.
1399 mlx5_get_dbr(struct rte_eth_dev *dev, struct mlx5_devx_dbr_page **dbr_page)
1401 struct mlx5_priv *priv = dev->data->dev_private;
1402 struct mlx5_devx_dbr_page *page = NULL;
1405 LIST_FOREACH(page, &priv->dbrpgs, next)
1406 if (page->dbr_count < MLX5_DBR_PER_PAGE)
1408 if (!page) { /* No page with free door-bell exists. */
1409 page = mlx5_alloc_dbr_page(dev);
1410 if (!page) /* Failed to allocate new page. */
1412 LIST_INSERT_HEAD(&priv->dbrpgs, page, next);
1414 /* Loop to find bitmap part with clear bit. */
1416 i < MLX5_DBR_BITMAP_SIZE && page->dbr_bitmap[i] == UINT64_MAX;
1419 /* Find the first clear bit. */
1420 j = rte_bsf64(~page->dbr_bitmap[i]);
1421 assert(i < (MLX5_DBR_PER_PAGE / 64));
1422 page->dbr_bitmap[i] |= (1 << j);
1425 return (((i * 64) + j) * sizeof(uint64_t));
1429 * Release a door-bell record.
1432 * Pointer to Ethernet device.
1433 * @param [in] umem_id
1434 * UMEM ID of page containing the door-bell record to release.
1435 * @param [in] offset
1436 * Offset of door-bell record in page.
1439 * 0 on success, a negative error value otherwise.
1442 mlx5_release_dbr(struct rte_eth_dev *dev, uint32_t umem_id, uint64_t offset)
1444 struct mlx5_priv *priv = dev->data->dev_private;
1445 struct mlx5_devx_dbr_page *page = NULL;
1448 LIST_FOREACH(page, &priv->dbrpgs, next)
1449 /* Find the page this address belongs to. */
1450 if (page->umem->umem_id == umem_id)
1455 if (!page->dbr_count) {
1456 /* Page not used, free it and remove from list. */
1457 LIST_REMOVE(page, next);
1459 ret = -mlx5_glue->devx_umem_dereg(page->umem);
1462 /* Mark in bitmap that this door-bell is not in use. */
1463 offset /= MLX5_DBR_SIZE;
1464 int i = offset / 64;
1465 int j = offset % 64;
1467 page->dbr_bitmap[i] &= ~(1 << j);
1473 * Spawn an Ethernet device from Verbs information.
1476 * Backing DPDK device.
1478 * Verbs device parameters (name, port, switch_info) to spawn.
1480 * Device configuration parameters.
1483 * A valid Ethernet device object on success, NULL otherwise and rte_errno
1484 * is set. The following errors are defined:
1486 * EBUSY: device is not supposed to be spawned.
1487 * EEXIST: device is already spawned
1489 static struct rte_eth_dev *
1490 mlx5_dev_spawn(struct rte_device *dpdk_dev,
1491 struct mlx5_dev_spawn_data *spawn,
1492 struct mlx5_dev_config config)
1494 const struct mlx5_switch_info *switch_info = &spawn->info;
1495 struct mlx5_ibv_shared *sh = NULL;
1496 struct ibv_port_attr port_attr;
1497 struct mlx5dv_context dv_attr = { .comp_mask = 0 };
1498 struct rte_eth_dev *eth_dev = NULL;
1499 struct mlx5_priv *priv = NULL;
1501 unsigned int hw_padding = 0;
1503 unsigned int cqe_comp;
1504 unsigned int cqe_pad = 0;
1505 unsigned int tunnel_en = 0;
1506 unsigned int mpls_en = 0;
1507 unsigned int swp = 0;
1508 unsigned int mprq = 0;
1509 unsigned int mprq_min_stride_size_n = 0;
1510 unsigned int mprq_max_stride_size_n = 0;
1511 unsigned int mprq_min_stride_num_n = 0;
1512 unsigned int mprq_max_stride_num_n = 0;
1513 struct rte_ether_addr mac;
1514 char name[RTE_ETH_NAME_MAX_LEN];
1515 int own_domain_id = 0;
1519 /* Determine if this port representor is supposed to be spawned. */
1520 if (switch_info->representor && dpdk_dev->devargs) {
1521 struct rte_eth_devargs eth_da;
1523 err = rte_eth_devargs_parse(dpdk_dev->devargs->args, ð_da);
1526 DRV_LOG(ERR, "failed to process device arguments: %s",
1527 strerror(rte_errno));
1530 for (i = 0; i < eth_da.nb_representor_ports; ++i)
1531 if (eth_da.representor_ports[i] ==
1532 (uint16_t)switch_info->port_name)
1534 if (i == eth_da.nb_representor_ports) {
1539 /* Build device name. */
1540 if (!switch_info->representor)
1541 strlcpy(name, dpdk_dev->name, sizeof(name));
1543 snprintf(name, sizeof(name), "%s_representor_%u",
1544 dpdk_dev->name, switch_info->port_name);
1545 /* check if the device is already spawned */
1546 if (rte_eth_dev_get_port_by_name(name, &port_id) == 0) {
1550 DRV_LOG(DEBUG, "naming Ethernet device \"%s\"", name);
1551 if (rte_eal_process_type() == RTE_PROC_SECONDARY) {
1552 eth_dev = rte_eth_dev_attach_secondary(name);
1553 if (eth_dev == NULL) {
1554 DRV_LOG(ERR, "can not attach rte ethdev");
1558 eth_dev->device = dpdk_dev;
1559 eth_dev->dev_ops = &mlx5_dev_sec_ops;
1560 err = mlx5_proc_priv_init(eth_dev);
1563 /* Receive command fd from primary process */
1564 err = mlx5_mp_req_verbs_cmd_fd(eth_dev);
1567 /* Remap UAR for Tx queues. */
1568 err = mlx5_tx_uar_init_secondary(eth_dev, err);
1572 * Ethdev pointer is still required as input since
1573 * the primary device is not accessible from the
1574 * secondary process.
1576 eth_dev->rx_pkt_burst = mlx5_select_rx_function(eth_dev);
1577 eth_dev->tx_pkt_burst = mlx5_select_tx_function(eth_dev);
1580 sh = mlx5_alloc_shared_ibctx(spawn);
1583 config.devx = sh->devx;
1584 #ifdef HAVE_MLX5DV_DR_ACTION_DEST_DEVX_TIR
1585 config.dest_tir = 1;
1587 #ifdef HAVE_IBV_MLX5_MOD_SWP
1588 dv_attr.comp_mask |= MLX5DV_CONTEXT_MASK_SWP;
1591 * Multi-packet send is supported by ConnectX-4 Lx PF as well
1592 * as all ConnectX-5 devices.
1594 #ifdef HAVE_IBV_DEVICE_TUNNEL_SUPPORT
1595 dv_attr.comp_mask |= MLX5DV_CONTEXT_MASK_TUNNEL_OFFLOADS;
1597 #ifdef HAVE_IBV_DEVICE_STRIDING_RQ_SUPPORT
1598 dv_attr.comp_mask |= MLX5DV_CONTEXT_MASK_STRIDING_RQ;
1600 mlx5_glue->dv_query_device(sh->ctx, &dv_attr);
1601 if (dv_attr.flags & MLX5DV_CONTEXT_FLAGS_MPW_ALLOWED) {
1602 if (dv_attr.flags & MLX5DV_CONTEXT_FLAGS_ENHANCED_MPW) {
1603 DRV_LOG(DEBUG, "enhanced MPW is supported");
1604 mps = MLX5_MPW_ENHANCED;
1606 DRV_LOG(DEBUG, "MPW is supported");
1610 DRV_LOG(DEBUG, "MPW isn't supported");
1611 mps = MLX5_MPW_DISABLED;
1613 #ifdef HAVE_IBV_MLX5_MOD_SWP
1614 if (dv_attr.comp_mask & MLX5DV_CONTEXT_MASK_SWP)
1615 swp = dv_attr.sw_parsing_caps.sw_parsing_offloads;
1616 DRV_LOG(DEBUG, "SWP support: %u", swp);
1619 #ifdef HAVE_IBV_DEVICE_STRIDING_RQ_SUPPORT
1620 if (dv_attr.comp_mask & MLX5DV_CONTEXT_MASK_STRIDING_RQ) {
1621 struct mlx5dv_striding_rq_caps mprq_caps =
1622 dv_attr.striding_rq_caps;
1624 DRV_LOG(DEBUG, "\tmin_single_stride_log_num_of_bytes: %d",
1625 mprq_caps.min_single_stride_log_num_of_bytes);
1626 DRV_LOG(DEBUG, "\tmax_single_stride_log_num_of_bytes: %d",
1627 mprq_caps.max_single_stride_log_num_of_bytes);
1628 DRV_LOG(DEBUG, "\tmin_single_wqe_log_num_of_strides: %d",
1629 mprq_caps.min_single_wqe_log_num_of_strides);
1630 DRV_LOG(DEBUG, "\tmax_single_wqe_log_num_of_strides: %d",
1631 mprq_caps.max_single_wqe_log_num_of_strides);
1632 DRV_LOG(DEBUG, "\tsupported_qpts: %d",
1633 mprq_caps.supported_qpts);
1634 DRV_LOG(DEBUG, "device supports Multi-Packet RQ");
1636 mprq_min_stride_size_n =
1637 mprq_caps.min_single_stride_log_num_of_bytes;
1638 mprq_max_stride_size_n =
1639 mprq_caps.max_single_stride_log_num_of_bytes;
1640 mprq_min_stride_num_n =
1641 mprq_caps.min_single_wqe_log_num_of_strides;
1642 mprq_max_stride_num_n =
1643 mprq_caps.max_single_wqe_log_num_of_strides;
1644 config.mprq.stride_num_n = RTE_MAX(MLX5_MPRQ_STRIDE_NUM_N,
1645 mprq_min_stride_num_n);
1648 if (RTE_CACHE_LINE_SIZE == 128 &&
1649 !(dv_attr.flags & MLX5DV_CONTEXT_FLAGS_CQE_128B_COMP))
1653 config.cqe_comp = cqe_comp;
1654 #ifdef HAVE_IBV_MLX5_MOD_CQE_128B_PAD
1655 /* Whether device supports 128B Rx CQE padding. */
1656 cqe_pad = RTE_CACHE_LINE_SIZE == 128 &&
1657 (dv_attr.flags & MLX5DV_CONTEXT_FLAGS_CQE_128B_PAD);
1659 #ifdef HAVE_IBV_DEVICE_TUNNEL_SUPPORT
1660 if (dv_attr.comp_mask & MLX5DV_CONTEXT_MASK_TUNNEL_OFFLOADS) {
1661 tunnel_en = ((dv_attr.tunnel_offloads_caps &
1662 MLX5DV_RAW_PACKET_CAP_TUNNELED_OFFLOAD_VXLAN) &&
1663 (dv_attr.tunnel_offloads_caps &
1664 MLX5DV_RAW_PACKET_CAP_TUNNELED_OFFLOAD_GRE));
1666 DRV_LOG(DEBUG, "tunnel offloading is %ssupported",
1667 tunnel_en ? "" : "not ");
1670 "tunnel offloading disabled due to old OFED/rdma-core version");
1672 config.tunnel_en = tunnel_en;
1673 #ifdef HAVE_IBV_DEVICE_MPLS_SUPPORT
1674 mpls_en = ((dv_attr.tunnel_offloads_caps &
1675 MLX5DV_RAW_PACKET_CAP_TUNNELED_OFFLOAD_CW_MPLS_OVER_GRE) &&
1676 (dv_attr.tunnel_offloads_caps &
1677 MLX5DV_RAW_PACKET_CAP_TUNNELED_OFFLOAD_CW_MPLS_OVER_UDP));
1678 DRV_LOG(DEBUG, "MPLS over GRE/UDP tunnel offloading is %ssupported",
1679 mpls_en ? "" : "not ");
1681 DRV_LOG(WARNING, "MPLS over GRE/UDP tunnel offloading disabled due to"
1682 " old OFED/rdma-core version or firmware configuration");
1684 config.mpls_en = mpls_en;
1685 /* Check port status. */
1686 err = mlx5_glue->query_port(sh->ctx, spawn->ibv_port, &port_attr);
1688 DRV_LOG(ERR, "port query failed: %s", strerror(err));
1691 if (port_attr.link_layer != IBV_LINK_LAYER_ETHERNET) {
1692 DRV_LOG(ERR, "port is not configured in Ethernet mode");
1696 if (port_attr.state != IBV_PORT_ACTIVE)
1697 DRV_LOG(DEBUG, "port is not active: \"%s\" (%d)",
1698 mlx5_glue->port_state_str(port_attr.state),
1700 /* Allocate private eth device data. */
1701 priv = rte_zmalloc("ethdev private structure",
1703 RTE_CACHE_LINE_SIZE);
1705 DRV_LOG(ERR, "priv allocation failure");
1710 priv->ibv_port = spawn->ibv_port;
1711 priv->mtu = RTE_ETHER_MTU;
1713 /* Initialize UAR access locks for 32bit implementations. */
1714 rte_spinlock_init(&priv->uar_lock_cq);
1715 for (i = 0; i < MLX5_UAR_PAGE_NUM_MAX; i++)
1716 rte_spinlock_init(&priv->uar_lock[i]);
1718 /* Some internal functions rely on Netlink sockets, open them now. */
1719 priv->nl_socket_rdma = mlx5_nl_init(NETLINK_RDMA);
1720 priv->nl_socket_route = mlx5_nl_init(NETLINK_ROUTE);
1722 priv->representor = !!switch_info->representor;
1723 priv->master = !!switch_info->master;
1724 priv->domain_id = RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID;
1726 * Currently we support single E-Switch per PF configurations
1727 * only and vport_id field contains the vport index for
1728 * associated VF, which is deduced from representor port name.
1729 * For example, let's have the IB device port 10, it has
1730 * attached network device eth0, which has port name attribute
1731 * pf0vf2, we can deduce the VF number as 2, and set vport index
1732 * as 3 (2+1). This assigning schema should be changed if the
1733 * multiple E-Switch instances per PF configurations or/and PCI
1734 * subfunctions are added.
1736 priv->vport_id = switch_info->representor ?
1737 switch_info->port_name + 1 : -1;
1738 /* representor_id field keeps the unmodified port/VF index. */
1739 priv->representor_id = switch_info->representor ?
1740 switch_info->port_name : -1;
1742 * Look for sibling devices in order to reuse their switch domain
1743 * if any, otherwise allocate one.
1745 RTE_ETH_FOREACH_DEV_OF(port_id, dpdk_dev) {
1746 const struct mlx5_priv *opriv =
1747 rte_eth_devices[port_id].data->dev_private;
1751 RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID)
1753 priv->domain_id = opriv->domain_id;
1756 if (priv->domain_id == RTE_ETH_DEV_SWITCH_DOMAIN_ID_INVALID) {
1757 err = rte_eth_switch_domain_alloc(&priv->domain_id);
1760 DRV_LOG(ERR, "unable to allocate switch domain: %s",
1761 strerror(rte_errno));
1766 err = mlx5_args(&config, dpdk_dev->devargs);
1769 DRV_LOG(ERR, "failed to process device arguments: %s",
1770 strerror(rte_errno));
1773 config.hw_csum = !!(sh->device_attr.device_cap_flags_ex &
1774 IBV_DEVICE_RAW_IP_CSUM);
1775 DRV_LOG(DEBUG, "checksum offloading is %ssupported",
1776 (config.hw_csum ? "" : "not "));
1777 #if !defined(HAVE_IBV_DEVICE_COUNTERS_SET_V42) && \
1778 !defined(HAVE_IBV_DEVICE_COUNTERS_SET_V45)
1779 DRV_LOG(DEBUG, "counters are not supported");
1781 #ifndef HAVE_IBV_FLOW_DV_SUPPORT
1782 if (config.dv_flow_en) {
1783 DRV_LOG(WARNING, "DV flow is not supported");
1784 config.dv_flow_en = 0;
1787 config.ind_table_max_size =
1788 sh->device_attr.rss_caps.max_rwq_indirection_table_size;
1790 * Remove this check once DPDK supports larger/variable
1791 * indirection tables.
1793 if (config.ind_table_max_size > (unsigned int)ETH_RSS_RETA_SIZE_512)
1794 config.ind_table_max_size = ETH_RSS_RETA_SIZE_512;
1795 DRV_LOG(DEBUG, "maximum Rx indirection table size is %u",
1796 config.ind_table_max_size);
1797 config.hw_vlan_strip = !!(sh->device_attr.raw_packet_caps &
1798 IBV_RAW_PACKET_CAP_CVLAN_STRIPPING);
1799 DRV_LOG(DEBUG, "VLAN stripping is %ssupported",
1800 (config.hw_vlan_strip ? "" : "not "));
1801 config.hw_fcs_strip = !!(sh->device_attr.raw_packet_caps &
1802 IBV_RAW_PACKET_CAP_SCATTER_FCS);
1803 DRV_LOG(DEBUG, "FCS stripping configuration is %ssupported",
1804 (config.hw_fcs_strip ? "" : "not "));
1805 #if defined(HAVE_IBV_WQ_FLAG_RX_END_PADDING)
1806 hw_padding = !!sh->device_attr.rx_pad_end_addr_align;
1807 #elif defined(HAVE_IBV_WQ_FLAGS_PCI_WRITE_END_PADDING)
1808 hw_padding = !!(sh->device_attr.device_cap_flags_ex &
1809 IBV_DEVICE_PCI_WRITE_END_PADDING);
1811 if (config.hw_padding && !hw_padding) {
1812 DRV_LOG(DEBUG, "Rx end alignment padding isn't supported");
1813 config.hw_padding = 0;
1814 } else if (config.hw_padding) {
1815 DRV_LOG(DEBUG, "Rx end alignment padding is enabled");
1817 config.tso = (sh->device_attr.tso_caps.max_tso > 0 &&
1818 (sh->device_attr.tso_caps.supported_qpts &
1819 (1 << IBV_QPT_RAW_PACKET)));
1821 config.tso_max_payload_sz = sh->device_attr.tso_caps.max_tso;
1823 * MPW is disabled by default, while the Enhanced MPW is enabled
1826 if (config.mps == MLX5_ARG_UNSET)
1827 config.mps = (mps == MLX5_MPW_ENHANCED) ? MLX5_MPW_ENHANCED :
1830 config.mps = config.mps ? mps : MLX5_MPW_DISABLED;
1831 DRV_LOG(INFO, "%sMPS is %s",
1832 config.mps == MLX5_MPW_ENHANCED ? "enhanced " : "",
1833 config.mps != MLX5_MPW_DISABLED ? "enabled" : "disabled");
1834 if (config.cqe_comp && !cqe_comp) {
1835 DRV_LOG(WARNING, "Rx CQE compression isn't supported");
1836 config.cqe_comp = 0;
1838 if (config.cqe_pad && !cqe_pad) {
1839 DRV_LOG(WARNING, "Rx CQE padding isn't supported");
1841 } else if (config.cqe_pad) {
1842 DRV_LOG(INFO, "Rx CQE padding is enabled");
1845 priv->counter_fallback = 0;
1846 err = mlx5_devx_cmd_query_hca_attr(sh->ctx, &config.hca_attr);
1851 if (!config.hca_attr.flow_counters_dump)
1852 priv->counter_fallback = 1;
1853 #ifndef HAVE_IBV_DEVX_ASYNC
1854 priv->counter_fallback = 1;
1856 if (priv->counter_fallback)
1857 DRV_LOG(INFO, "Use fall-back DV counter management\n");
1858 /* Check for LRO support. */
1859 if (config.dest_tir && mprq && config.hca_attr.lro_cap) {
1860 /* TBD check tunnel lro caps. */
1861 config.lro.supported = config.hca_attr.lro_cap;
1862 DRV_LOG(DEBUG, "Device supports LRO");
1864 * If LRO timeout is not configured by application,
1865 * use the minimal supported value.
1867 if (!config.lro.timeout)
1868 config.lro.timeout =
1869 config.hca_attr.lro_timer_supported_periods[0];
1870 DRV_LOG(DEBUG, "LRO session timeout set to %d usec",
1871 config.lro.timeout);
1872 config.mprq.enabled = 1;
1873 DRV_LOG(DEBUG, "Enable MPRQ for LRO use");
1876 if (config.mprq.enabled && mprq) {
1877 if (config.mprq.stride_num_n > mprq_max_stride_num_n ||
1878 config.mprq.stride_num_n < mprq_min_stride_num_n) {
1879 config.mprq.stride_num_n =
1880 RTE_MAX(MLX5_MPRQ_STRIDE_NUM_N,
1881 mprq_min_stride_num_n);
1883 "the number of strides"
1884 " for Multi-Packet RQ is out of range,"
1885 " setting default value (%u)",
1886 1 << config.mprq.stride_num_n);
1888 config.mprq.min_stride_size_n = mprq_min_stride_size_n;
1889 config.mprq.max_stride_size_n = mprq_max_stride_size_n;
1890 } else if (config.mprq.enabled && !mprq) {
1891 DRV_LOG(WARNING, "Multi-Packet RQ isn't supported");
1892 config.mprq.enabled = 0;
1894 if (config.max_dump_files_num == 0)
1895 config.max_dump_files_num = 128;
1896 eth_dev = rte_eth_dev_allocate(name);
1897 if (eth_dev == NULL) {
1898 DRV_LOG(ERR, "can not allocate rte ethdev");
1902 /* Flag to call rte_eth_dev_release_port() in rte_eth_dev_close(). */
1903 eth_dev->data->dev_flags |= RTE_ETH_DEV_CLOSE_REMOVE;
1904 if (priv->representor) {
1905 eth_dev->data->dev_flags |= RTE_ETH_DEV_REPRESENTOR;
1906 eth_dev->data->representor_id = priv->representor_id;
1909 * Store associated network device interface index. This index
1910 * is permanent throughout the lifetime of device. So, we may store
1911 * the ifindex here and use the cached value further.
1913 assert(spawn->ifindex);
1914 priv->if_index = spawn->ifindex;
1915 eth_dev->data->dev_private = priv;
1916 priv->dev_data = eth_dev->data;
1917 eth_dev->data->mac_addrs = priv->mac;
1918 eth_dev->device = dpdk_dev;
1919 /* Configure the first MAC address by default. */
1920 if (mlx5_get_mac(eth_dev, &mac.addr_bytes)) {
1922 "port %u cannot get MAC address, is mlx5_en"
1923 " loaded? (errno: %s)",
1924 eth_dev->data->port_id, strerror(rte_errno));
1929 "port %u MAC address is %02x:%02x:%02x:%02x:%02x:%02x",
1930 eth_dev->data->port_id,
1931 mac.addr_bytes[0], mac.addr_bytes[1],
1932 mac.addr_bytes[2], mac.addr_bytes[3],
1933 mac.addr_bytes[4], mac.addr_bytes[5]);
1936 char ifname[IF_NAMESIZE];
1938 if (mlx5_get_ifname(eth_dev, &ifname) == 0)
1939 DRV_LOG(DEBUG, "port %u ifname is \"%s\"",
1940 eth_dev->data->port_id, ifname);
1942 DRV_LOG(DEBUG, "port %u ifname is unknown",
1943 eth_dev->data->port_id);
1946 /* Get actual MTU if possible. */
1947 err = mlx5_get_mtu(eth_dev, &priv->mtu);
1952 DRV_LOG(DEBUG, "port %u MTU is %u", eth_dev->data->port_id,
1954 /* Initialize burst functions to prevent crashes before link-up. */
1955 eth_dev->rx_pkt_burst = removed_rx_burst;
1956 eth_dev->tx_pkt_burst = removed_tx_burst;
1957 eth_dev->dev_ops = &mlx5_dev_ops;
1958 /* Register MAC address. */
1959 claim_zero(mlx5_mac_addr_add(eth_dev, &mac, 0, 0));
1960 if (config.vf && config.vf_nl_en)
1961 mlx5_nl_mac_addr_sync(eth_dev);
1962 TAILQ_INIT(&priv->flows);
1963 TAILQ_INIT(&priv->ctrl_flows);
1964 /* Hint libmlx5 to use PMD allocator for data plane resources */
1965 struct mlx5dv_ctx_allocators alctr = {
1966 .alloc = &mlx5_alloc_verbs_buf,
1967 .free = &mlx5_free_verbs_buf,
1970 mlx5_glue->dv_set_context_attr(sh->ctx,
1971 MLX5DV_CTX_ATTR_BUF_ALLOCATORS,
1972 (void *)((uintptr_t)&alctr));
1973 /* Bring Ethernet device up. */
1974 DRV_LOG(DEBUG, "port %u forcing Ethernet interface up",
1975 eth_dev->data->port_id);
1976 mlx5_set_link_up(eth_dev);
1978 * Even though the interrupt handler is not installed yet,
1979 * interrupts will still trigger on the async_fd from
1980 * Verbs context returned by ibv_open_device().
1982 mlx5_link_update(eth_dev, 0);
1983 #ifdef HAVE_MLX5DV_DR_ESWITCH
1984 if (!(config.hca_attr.eswitch_manager && config.dv_flow_en &&
1985 (switch_info->representor || switch_info->master)))
1986 config.dv_esw_en = 0;
1988 config.dv_esw_en = 0;
1990 /* Detect minimal data bytes to inline. */
1991 mlx5_set_min_inline(spawn, &config);
1992 /* Store device configuration on private structure. */
1993 priv->config = config;
1994 if (config.dv_flow_en) {
1995 err = mlx5_alloc_shared_dr(priv);
1999 /* Supported Verbs flow priority number detection. */
2000 err = mlx5_flow_discover_priorities(eth_dev);
2005 priv->config.flow_prio = err;
2006 /* Add device to memory callback list. */
2007 rte_rwlock_write_lock(&mlx5_shared_data->mem_event_rwlock);
2008 LIST_INSERT_HEAD(&mlx5_shared_data->mem_event_cb_list,
2010 rte_rwlock_write_unlock(&mlx5_shared_data->mem_event_rwlock);
2015 mlx5_free_shared_dr(priv);
2016 if (priv->nl_socket_route >= 0)
2017 close(priv->nl_socket_route);
2018 if (priv->nl_socket_rdma >= 0)
2019 close(priv->nl_socket_rdma);
2021 claim_zero(rte_eth_switch_domain_free(priv->domain_id));
2023 if (eth_dev != NULL)
2024 eth_dev->data->dev_private = NULL;
2026 if (eth_dev != NULL) {
2027 /* mac_addrs must not be freed alone because part of dev_private */
2028 eth_dev->data->mac_addrs = NULL;
2029 rte_eth_dev_release_port(eth_dev);
2032 mlx5_free_shared_ibctx(sh);
2039 * Comparison callback to sort device data.
2041 * This is meant to be used with qsort().
2044 * Pointer to pointer to first data object.
2046 * Pointer to pointer to second data object.
2049 * 0 if both objects are equal, less than 0 if the first argument is less
2050 * than the second, greater than 0 otherwise.
2053 mlx5_dev_spawn_data_cmp(const void *a, const void *b)
2055 const struct mlx5_switch_info *si_a =
2056 &((const struct mlx5_dev_spawn_data *)a)->info;
2057 const struct mlx5_switch_info *si_b =
2058 &((const struct mlx5_dev_spawn_data *)b)->info;
2061 /* Master device first. */
2062 ret = si_b->master - si_a->master;
2065 /* Then representor devices. */
2066 ret = si_b->representor - si_a->representor;
2069 /* Unidentified devices come last in no specific order. */
2070 if (!si_a->representor)
2072 /* Order representors by name. */
2073 return si_a->port_name - si_b->port_name;
2077 * DPDK callback to register a PCI device.
2079 * This function spawns Ethernet devices out of a given PCI device.
2081 * @param[in] pci_drv
2082 * PCI driver structure (mlx5_driver).
2083 * @param[in] pci_dev
2084 * PCI device information.
2087 * 0 on success, a negative errno value otherwise and rte_errno is set.
2090 mlx5_pci_probe(struct rte_pci_driver *pci_drv __rte_unused,
2091 struct rte_pci_device *pci_dev)
2093 struct ibv_device **ibv_list;
2095 * Number of found IB Devices matching with requested PCI BDF.
2096 * nd != 1 means there are multiple IB devices over the same
2097 * PCI device and we have representors and master.
2099 unsigned int nd = 0;
2101 * Number of found IB device Ports. nd = 1 and np = 1..n means
2102 * we have the single multiport IB device, and there may be
2103 * representors attached to some of found ports.
2105 unsigned int np = 0;
2107 * Number of DPDK ethernet devices to Spawn - either over
2108 * multiple IB devices or multiple ports of single IB device.
2109 * Actually this is the number of iterations to spawn.
2111 unsigned int ns = 0;
2112 struct mlx5_dev_config dev_config;
2115 ret = mlx5_init_once();
2117 DRV_LOG(ERR, "unable to init PMD global data: %s",
2118 strerror(rte_errno));
2121 assert(pci_drv == &mlx5_driver);
2123 ibv_list = mlx5_glue->get_device_list(&ret);
2125 rte_errno = errno ? errno : ENOSYS;
2126 DRV_LOG(ERR, "cannot list devices, is ib_uverbs loaded?");
2130 * First scan the list of all Infiniband devices to find
2131 * matching ones, gathering into the list.
2133 struct ibv_device *ibv_match[ret + 1];
2139 struct rte_pci_addr pci_addr;
2141 DRV_LOG(DEBUG, "checking device \"%s\"", ibv_list[ret]->name);
2142 if (mlx5_ibv_device_to_pci_addr(ibv_list[ret], &pci_addr))
2144 if (pci_dev->addr.domain != pci_addr.domain ||
2145 pci_dev->addr.bus != pci_addr.bus ||
2146 pci_dev->addr.devid != pci_addr.devid ||
2147 pci_dev->addr.function != pci_addr.function)
2149 DRV_LOG(INFO, "PCI information matches for device \"%s\"",
2150 ibv_list[ret]->name);
2151 ibv_match[nd++] = ibv_list[ret];
2153 ibv_match[nd] = NULL;
2155 /* No device matches, just complain and bail out. */
2156 mlx5_glue->free_device_list(ibv_list);
2158 "no Verbs device matches PCI device " PCI_PRI_FMT ","
2159 " are kernel drivers loaded?",
2160 pci_dev->addr.domain, pci_dev->addr.bus,
2161 pci_dev->addr.devid, pci_dev->addr.function);
2166 nl_route = mlx5_nl_init(NETLINK_ROUTE);
2167 nl_rdma = mlx5_nl_init(NETLINK_RDMA);
2170 * Found single matching device may have multiple ports.
2171 * Each port may be representor, we have to check the port
2172 * number and check the representors existence.
2175 np = mlx5_nl_portnum(nl_rdma, ibv_match[0]->name);
2177 DRV_LOG(WARNING, "can not get IB device \"%s\""
2178 " ports number", ibv_match[0]->name);
2181 * Now we can determine the maximal
2182 * amount of devices to be spawned.
2184 struct mlx5_dev_spawn_data list[np ? np : nd];
2188 * Single IB device with multiple ports found,
2189 * it may be E-Switch master device and representors.
2190 * We have to perform identification trough the ports.
2192 assert(nl_rdma >= 0);
2195 for (i = 1; i <= np; ++i) {
2196 list[ns].max_port = np;
2197 list[ns].ibv_port = i;
2198 list[ns].ibv_dev = ibv_match[0];
2199 list[ns].eth_dev = NULL;
2200 list[ns].pci_dev = pci_dev;
2201 list[ns].ifindex = mlx5_nl_ifindex
2202 (nl_rdma, list[ns].ibv_dev->name, i);
2203 if (!list[ns].ifindex) {
2205 * No network interface index found for the
2206 * specified port, it means there is no
2207 * representor on this port. It's OK,
2208 * there can be disabled ports, for example
2209 * if sriov_numvfs < sriov_totalvfs.
2215 ret = mlx5_nl_switch_info
2219 if (ret || (!list[ns].info.representor &&
2220 !list[ns].info.master)) {
2222 * We failed to recognize representors with
2223 * Netlink, let's try to perform the task
2226 ret = mlx5_sysfs_switch_info
2230 if (!ret && (list[ns].info.representor ^
2231 list[ns].info.master))
2236 "unable to recognize master/representors"
2237 " on the IB device with multiple ports");
2244 * The existence of several matching entries (nd > 1) means
2245 * port representors have been instantiated. No existing Verbs
2246 * call nor sysfs entries can tell them apart, this can only
2247 * be done through Netlink calls assuming kernel drivers are
2248 * recent enough to support them.
2250 * In the event of identification failure through Netlink,
2251 * try again through sysfs, then:
2253 * 1. A single IB device matches (nd == 1) with single
2254 * port (np=0/1) and is not a representor, assume
2255 * no switch support.
2257 * 2. Otherwise no safe assumptions can be made;
2258 * complain louder and bail out.
2261 for (i = 0; i != nd; ++i) {
2262 memset(&list[ns].info, 0, sizeof(list[ns].info));
2263 list[ns].max_port = 1;
2264 list[ns].ibv_port = 1;
2265 list[ns].ibv_dev = ibv_match[i];
2266 list[ns].eth_dev = NULL;
2267 list[ns].pci_dev = pci_dev;
2268 list[ns].ifindex = 0;
2270 list[ns].ifindex = mlx5_nl_ifindex
2271 (nl_rdma, list[ns].ibv_dev->name, 1);
2272 if (!list[ns].ifindex) {
2273 char ifname[IF_NAMESIZE];
2276 * Netlink failed, it may happen with old
2277 * ib_core kernel driver (before 4.16).
2278 * We can assume there is old driver because
2279 * here we are processing single ports IB
2280 * devices. Let's try sysfs to retrieve
2281 * the ifindex. The method works for
2282 * master device only.
2286 * Multiple devices found, assume
2287 * representors, can not distinguish
2288 * master/representor and retrieve
2289 * ifindex via sysfs.
2293 ret = mlx5_get_master_ifname
2294 (ibv_match[i]->ibdev_path, &ifname);
2297 if_nametoindex(ifname);
2298 if (!list[ns].ifindex) {
2300 * No network interface index found
2301 * for the specified device, it means
2302 * there it is neither representor
2310 ret = mlx5_nl_switch_info
2314 if (ret || (!list[ns].info.representor &&
2315 !list[ns].info.master)) {
2317 * We failed to recognize representors with
2318 * Netlink, let's try to perform the task
2321 ret = mlx5_sysfs_switch_info
2325 if (!ret && (list[ns].info.representor ^
2326 list[ns].info.master)) {
2328 } else if ((nd == 1) &&
2329 !list[ns].info.representor &&
2330 !list[ns].info.master) {
2332 * Single IB device with
2333 * one physical port and
2334 * attached network device.
2335 * May be SRIOV is not enabled
2336 * or there is no representors.
2338 DRV_LOG(INFO, "no E-Switch support detected");
2345 "unable to recognize master/representors"
2346 " on the multiple IB devices");
2354 * Sort list to probe devices in natural order for users convenience
2355 * (i.e. master first, then representors from lowest to highest ID).
2357 qsort(list, ns, sizeof(*list), mlx5_dev_spawn_data_cmp);
2358 /* Default configuration. */
2359 dev_config = (struct mlx5_dev_config){
2361 .mps = MLX5_ARG_UNSET,
2363 .txq_inline_max = MLX5_ARG_UNSET,
2364 .txq_inline_min = MLX5_ARG_UNSET,
2365 .txq_inline_mpw = MLX5_ARG_UNSET,
2366 .txqs_inline = MLX5_ARG_UNSET,
2368 .mr_ext_memseg_en = 1,
2370 .enabled = 0, /* Disabled by default. */
2371 .stride_num_n = MLX5_MPRQ_STRIDE_NUM_N,
2372 .max_memcpy_len = MLX5_MPRQ_MEMCPY_DEFAULT_LEN,
2373 .min_rxqs_num = MLX5_MPRQ_MIN_RXQS,
2377 /* Device specific configuration. */
2378 switch (pci_dev->id.device_id) {
2379 case PCI_DEVICE_ID_MELLANOX_CONNECTX4VF:
2380 case PCI_DEVICE_ID_MELLANOX_CONNECTX4LXVF:
2381 case PCI_DEVICE_ID_MELLANOX_CONNECTX5VF:
2382 case PCI_DEVICE_ID_MELLANOX_CONNECTX5EXVF:
2388 for (i = 0; i != ns; ++i) {
2391 list[i].eth_dev = mlx5_dev_spawn(&pci_dev->device,
2394 if (!list[i].eth_dev) {
2395 if (rte_errno != EBUSY && rte_errno != EEXIST)
2397 /* Device is disabled or already spawned. Ignore it. */
2400 restore = list[i].eth_dev->data->dev_flags;
2401 rte_eth_copy_pci_info(list[i].eth_dev, pci_dev);
2402 /* Restore non-PCI flags cleared by the above call. */
2403 list[i].eth_dev->data->dev_flags |= restore;
2404 rte_eth_dev_probing_finish(list[i].eth_dev);
2408 "probe of PCI device " PCI_PRI_FMT " aborted after"
2409 " encountering an error: %s",
2410 pci_dev->addr.domain, pci_dev->addr.bus,
2411 pci_dev->addr.devid, pci_dev->addr.function,
2412 strerror(rte_errno));
2416 if (!list[i].eth_dev)
2418 mlx5_dev_close(list[i].eth_dev);
2419 /* mac_addrs must not be freed because in dev_private */
2420 list[i].eth_dev->data->mac_addrs = NULL;
2421 claim_zero(rte_eth_dev_release_port(list[i].eth_dev));
2423 /* Restore original error. */
2430 * Do the routine cleanup:
2431 * - close opened Netlink sockets
2432 * - free the Infiniband device list
2439 mlx5_glue->free_device_list(ibv_list);
2444 * DPDK callback to remove a PCI device.
2446 * This function removes all Ethernet devices belong to a given PCI device.
2448 * @param[in] pci_dev
2449 * Pointer to the PCI device.
2452 * 0 on success, the function cannot fail.
2455 mlx5_pci_remove(struct rte_pci_device *pci_dev)
2459 RTE_ETH_FOREACH_DEV_OF(port_id, &pci_dev->device)
2460 rte_eth_dev_close(port_id);
2464 static const struct rte_pci_id mlx5_pci_id_map[] = {
2466 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2467 PCI_DEVICE_ID_MELLANOX_CONNECTX4)
2470 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2471 PCI_DEVICE_ID_MELLANOX_CONNECTX4VF)
2474 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2475 PCI_DEVICE_ID_MELLANOX_CONNECTX4LX)
2478 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2479 PCI_DEVICE_ID_MELLANOX_CONNECTX4LXVF)
2482 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2483 PCI_DEVICE_ID_MELLANOX_CONNECTX5)
2486 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2487 PCI_DEVICE_ID_MELLANOX_CONNECTX5VF)
2490 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2491 PCI_DEVICE_ID_MELLANOX_CONNECTX5EX)
2494 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2495 PCI_DEVICE_ID_MELLANOX_CONNECTX5EXVF)
2498 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2499 PCI_DEVICE_ID_MELLANOX_CONNECTX5BF)
2502 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2503 PCI_DEVICE_ID_MELLANOX_CONNECTX5BFVF)
2506 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2507 PCI_DEVICE_ID_MELLANOX_CONNECTX6)
2510 RTE_PCI_DEVICE(PCI_VENDOR_ID_MELLANOX,
2511 PCI_DEVICE_ID_MELLANOX_CONNECTX6VF)
2518 static struct rte_pci_driver mlx5_driver = {
2520 .name = MLX5_DRIVER_NAME
2522 .id_table = mlx5_pci_id_map,
2523 .probe = mlx5_pci_probe,
2524 .remove = mlx5_pci_remove,
2525 .dma_map = mlx5_dma_map,
2526 .dma_unmap = mlx5_dma_unmap,
2527 .drv_flags = RTE_PCI_DRV_INTR_LSC | RTE_PCI_DRV_INTR_RMV |
2528 RTE_PCI_DRV_PROBE_AGAIN,
2531 #ifdef RTE_IBVERBS_LINK_DLOPEN
2534 * Suffix RTE_EAL_PMD_PATH with "-glue".
2536 * This function performs a sanity check on RTE_EAL_PMD_PATH before
2537 * suffixing its last component.
2540 * Output buffer, should be large enough otherwise NULL is returned.
2545 * Pointer to @p buf or @p NULL in case suffix cannot be appended.
2548 mlx5_glue_path(char *buf, size_t size)
2550 static const char *const bad[] = { "/", ".", "..", NULL };
2551 const char *path = RTE_EAL_PMD_PATH;
2552 size_t len = strlen(path);
2556 while (len && path[len - 1] == '/')
2558 for (off = len; off && path[off - 1] != '/'; --off)
2560 for (i = 0; bad[i]; ++i)
2561 if (!strncmp(path + off, bad[i], (int)(len - off)))
2563 i = snprintf(buf, size, "%.*s-glue", (int)len, path);
2564 if (i == -1 || (size_t)i >= size)
2569 "unable to append \"-glue\" to last component of"
2570 " RTE_EAL_PMD_PATH (\"" RTE_EAL_PMD_PATH "\"),"
2571 " please re-configure DPDK");
2576 * Initialization routine for run-time dependency on rdma-core.
2579 mlx5_glue_init(void)
2581 char glue_path[sizeof(RTE_EAL_PMD_PATH) - 1 + sizeof("-glue")];
2582 const char *path[] = {
2584 * A basic security check is necessary before trusting
2585 * MLX5_GLUE_PATH, which may override RTE_EAL_PMD_PATH.
2587 (geteuid() == getuid() && getegid() == getgid() ?
2588 getenv("MLX5_GLUE_PATH") : NULL),
2590 * When RTE_EAL_PMD_PATH is set, use its glue-suffixed
2591 * variant, otherwise let dlopen() look up libraries on its
2594 (*RTE_EAL_PMD_PATH ?
2595 mlx5_glue_path(glue_path, sizeof(glue_path)) : ""),
2598 void *handle = NULL;
2602 while (!handle && i != RTE_DIM(path)) {
2611 end = strpbrk(path[i], ":;");
2613 end = path[i] + strlen(path[i]);
2614 len = end - path[i];
2619 ret = snprintf(name, sizeof(name), "%.*s%s" MLX5_GLUE,
2621 (!len || *(end - 1) == '/') ? "" : "/");
2624 if (sizeof(name) != (size_t)ret + 1)
2626 DRV_LOG(DEBUG, "looking for rdma-core glue as \"%s\"",
2628 handle = dlopen(name, RTLD_LAZY);
2639 DRV_LOG(WARNING, "cannot load glue library: %s", dlmsg);
2642 sym = dlsym(handle, "mlx5_glue");
2643 if (!sym || !*sym) {
2647 DRV_LOG(ERR, "cannot resolve glue symbol: %s", dlmsg);
2656 "cannot initialize PMD due to missing run-time dependency on"
2657 " rdma-core libraries (libibverbs, libmlx5)");
2664 * Driver initialization routine.
2666 RTE_INIT(rte_mlx5_pmd_init)
2668 /* Initialize driver log type. */
2669 mlx5_logtype = rte_log_register("pmd.net.mlx5");
2670 if (mlx5_logtype >= 0)
2671 rte_log_set_level(mlx5_logtype, RTE_LOG_NOTICE);
2673 /* Build the static tables for Verbs conversion. */
2674 mlx5_set_ptype_table();
2675 mlx5_set_cksum_table();
2676 mlx5_set_swp_types_table();
2678 * RDMAV_HUGEPAGES_SAFE tells ibv_fork_init() we intend to use
2679 * huge pages. Calling ibv_fork_init() during init allows
2680 * applications to use fork() safely for purposes other than
2681 * using this PMD, which is not supported in forked processes.
2683 setenv("RDMAV_HUGEPAGES_SAFE", "1", 1);
2684 /* Match the size of Rx completion entry to the size of a cacheline. */
2685 if (RTE_CACHE_LINE_SIZE == 128)
2686 setenv("MLX5_CQE_SIZE", "128", 0);
2688 * MLX5_DEVICE_FATAL_CLEANUP tells ibv_destroy functions to
2689 * cleanup all the Verbs resources even when the device was removed.
2691 setenv("MLX5_DEVICE_FATAL_CLEANUP", "1", 1);
2692 #ifdef RTE_IBVERBS_LINK_DLOPEN
2693 if (mlx5_glue_init())
2698 /* Glue structure must not contain any NULL pointers. */
2702 for (i = 0; i != sizeof(*mlx5_glue) / sizeof(void *); ++i)
2703 assert(((const void *const *)mlx5_glue)[i]);
2706 if (strcmp(mlx5_glue->version, MLX5_GLUE_VERSION)) {
2708 "rdma-core glue \"%s\" mismatch: \"%s\" is required",
2709 mlx5_glue->version, MLX5_GLUE_VERSION);
2712 mlx5_glue->fork_init();
2713 rte_pci_register(&mlx5_driver);
2716 RTE_PMD_EXPORT_NAME(net_mlx5, __COUNTER__);
2717 RTE_PMD_REGISTER_PCI_TABLE(net_mlx5, mlx5_pci_id_map);
2718 RTE_PMD_REGISTER_KMOD_DEP(net_mlx5, "* ib_uverbs & mlx5_core & mlx5_ib");