1 /* SPDX-License-Identifier: BSD-3-Clause
2 * Copyright 2016 6WIND S.A.
3 * Copyright 2016 Mellanox Technologies, Ltd
6 #include <netinet/in.h>
13 /* ISO C doesn't support unnamed structs/unions, disabling -pedantic. */
15 #pragma GCC diagnostic ignored "-Wpedantic"
17 #include <infiniband/verbs.h>
19 #pragma GCC diagnostic error "-Wpedantic"
22 #include <rte_common.h>
23 #include <rte_ether.h>
24 #include <rte_eth_ctrl.h>
25 #include <rte_ethdev_driver.h>
27 #include <rte_flow_driver.h>
28 #include <rte_malloc.h>
32 #include "mlx5_defs.h"
34 #include "mlx5_glue.h"
35 #include "mlx5_flow.h"
37 /* Dev ops structure defined in mlx5.c */
38 extern const struct eth_dev_ops mlx5_dev_ops;
39 extern const struct eth_dev_ops mlx5_dev_ops_isolate;
41 /** Device flow drivers. */
42 #ifdef HAVE_IBV_FLOW_DV_SUPPORT
43 extern const struct mlx5_flow_driver_ops mlx5_flow_dv_drv_ops;
45 extern const struct mlx5_flow_driver_ops mlx5_flow_tcf_drv_ops;
46 extern const struct mlx5_flow_driver_ops mlx5_flow_verbs_drv_ops;
48 const struct mlx5_flow_driver_ops mlx5_flow_null_drv_ops;
50 const struct mlx5_flow_driver_ops *flow_drv_ops[] = {
51 [MLX5_FLOW_TYPE_MIN] = &mlx5_flow_null_drv_ops,
52 #ifdef HAVE_IBV_FLOW_DV_SUPPORT
53 [MLX5_FLOW_TYPE_DV] = &mlx5_flow_dv_drv_ops,
55 [MLX5_FLOW_TYPE_TCF] = &mlx5_flow_tcf_drv_ops,
56 [MLX5_FLOW_TYPE_VERBS] = &mlx5_flow_verbs_drv_ops,
57 [MLX5_FLOW_TYPE_MAX] = &mlx5_flow_null_drv_ops
62 MLX5_EXPANSION_ROOT_OUTER,
63 MLX5_EXPANSION_ROOT_ETH_VLAN,
64 MLX5_EXPANSION_ROOT_OUTER_ETH_VLAN,
65 MLX5_EXPANSION_OUTER_ETH,
66 MLX5_EXPANSION_OUTER_ETH_VLAN,
67 MLX5_EXPANSION_OUTER_VLAN,
68 MLX5_EXPANSION_OUTER_IPV4,
69 MLX5_EXPANSION_OUTER_IPV4_UDP,
70 MLX5_EXPANSION_OUTER_IPV4_TCP,
71 MLX5_EXPANSION_OUTER_IPV6,
72 MLX5_EXPANSION_OUTER_IPV6_UDP,
73 MLX5_EXPANSION_OUTER_IPV6_TCP,
75 MLX5_EXPANSION_VXLAN_GPE,
79 MLX5_EXPANSION_ETH_VLAN,
82 MLX5_EXPANSION_IPV4_UDP,
83 MLX5_EXPANSION_IPV4_TCP,
85 MLX5_EXPANSION_IPV6_UDP,
86 MLX5_EXPANSION_IPV6_TCP,
89 /** Supported expansion of items. */
90 static const struct rte_flow_expand_node mlx5_support_expansion[] = {
91 [MLX5_EXPANSION_ROOT] = {
92 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_ETH,
95 .type = RTE_FLOW_ITEM_TYPE_END,
97 [MLX5_EXPANSION_ROOT_OUTER] = {
98 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_OUTER_ETH,
99 MLX5_EXPANSION_OUTER_IPV4,
100 MLX5_EXPANSION_OUTER_IPV6),
101 .type = RTE_FLOW_ITEM_TYPE_END,
103 [MLX5_EXPANSION_ROOT_ETH_VLAN] = {
104 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_ETH_VLAN),
105 .type = RTE_FLOW_ITEM_TYPE_END,
107 [MLX5_EXPANSION_ROOT_OUTER_ETH_VLAN] = {
108 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_OUTER_ETH_VLAN),
109 .type = RTE_FLOW_ITEM_TYPE_END,
111 [MLX5_EXPANSION_OUTER_ETH] = {
112 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_OUTER_IPV4,
113 MLX5_EXPANSION_OUTER_IPV6,
114 MLX5_EXPANSION_MPLS),
115 .type = RTE_FLOW_ITEM_TYPE_ETH,
118 [MLX5_EXPANSION_OUTER_ETH_VLAN] = {
119 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_OUTER_VLAN),
120 .type = RTE_FLOW_ITEM_TYPE_ETH,
123 [MLX5_EXPANSION_OUTER_VLAN] = {
124 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_OUTER_IPV4,
125 MLX5_EXPANSION_OUTER_IPV6),
126 .type = RTE_FLOW_ITEM_TYPE_VLAN,
128 [MLX5_EXPANSION_OUTER_IPV4] = {
129 .next = RTE_FLOW_EXPAND_RSS_NEXT
130 (MLX5_EXPANSION_OUTER_IPV4_UDP,
131 MLX5_EXPANSION_OUTER_IPV4_TCP,
133 .type = RTE_FLOW_ITEM_TYPE_IPV4,
134 .rss_types = ETH_RSS_IPV4 | ETH_RSS_FRAG_IPV4 |
135 ETH_RSS_NONFRAG_IPV4_OTHER,
137 [MLX5_EXPANSION_OUTER_IPV4_UDP] = {
138 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_VXLAN,
139 MLX5_EXPANSION_VXLAN_GPE),
140 .type = RTE_FLOW_ITEM_TYPE_UDP,
141 .rss_types = ETH_RSS_NONFRAG_IPV4_UDP,
143 [MLX5_EXPANSION_OUTER_IPV4_TCP] = {
144 .type = RTE_FLOW_ITEM_TYPE_TCP,
145 .rss_types = ETH_RSS_NONFRAG_IPV4_TCP,
147 [MLX5_EXPANSION_OUTER_IPV6] = {
148 .next = RTE_FLOW_EXPAND_RSS_NEXT
149 (MLX5_EXPANSION_OUTER_IPV6_UDP,
150 MLX5_EXPANSION_OUTER_IPV6_TCP),
151 .type = RTE_FLOW_ITEM_TYPE_IPV6,
152 .rss_types = ETH_RSS_IPV6 | ETH_RSS_FRAG_IPV6 |
153 ETH_RSS_NONFRAG_IPV6_OTHER,
155 [MLX5_EXPANSION_OUTER_IPV6_UDP] = {
156 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_VXLAN,
157 MLX5_EXPANSION_VXLAN_GPE),
158 .type = RTE_FLOW_ITEM_TYPE_UDP,
159 .rss_types = ETH_RSS_NONFRAG_IPV6_UDP,
161 [MLX5_EXPANSION_OUTER_IPV6_TCP] = {
162 .type = RTE_FLOW_ITEM_TYPE_TCP,
163 .rss_types = ETH_RSS_NONFRAG_IPV6_TCP,
165 [MLX5_EXPANSION_VXLAN] = {
166 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_ETH),
167 .type = RTE_FLOW_ITEM_TYPE_VXLAN,
169 [MLX5_EXPANSION_VXLAN_GPE] = {
170 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_ETH,
172 MLX5_EXPANSION_IPV6),
173 .type = RTE_FLOW_ITEM_TYPE_VXLAN_GPE,
175 [MLX5_EXPANSION_GRE] = {
176 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_IPV4),
177 .type = RTE_FLOW_ITEM_TYPE_GRE,
179 [MLX5_EXPANSION_MPLS] = {
180 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_IPV4,
181 MLX5_EXPANSION_IPV6),
182 .type = RTE_FLOW_ITEM_TYPE_MPLS,
184 [MLX5_EXPANSION_ETH] = {
185 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_IPV4,
186 MLX5_EXPANSION_IPV6),
187 .type = RTE_FLOW_ITEM_TYPE_ETH,
189 [MLX5_EXPANSION_ETH_VLAN] = {
190 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_VLAN),
191 .type = RTE_FLOW_ITEM_TYPE_ETH,
193 [MLX5_EXPANSION_VLAN] = {
194 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_IPV4,
195 MLX5_EXPANSION_IPV6),
196 .type = RTE_FLOW_ITEM_TYPE_VLAN,
198 [MLX5_EXPANSION_IPV4] = {
199 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_IPV4_UDP,
200 MLX5_EXPANSION_IPV4_TCP),
201 .type = RTE_FLOW_ITEM_TYPE_IPV4,
202 .rss_types = ETH_RSS_IPV4 | ETH_RSS_FRAG_IPV4 |
203 ETH_RSS_NONFRAG_IPV4_OTHER,
205 [MLX5_EXPANSION_IPV4_UDP] = {
206 .type = RTE_FLOW_ITEM_TYPE_UDP,
207 .rss_types = ETH_RSS_NONFRAG_IPV4_UDP,
209 [MLX5_EXPANSION_IPV4_TCP] = {
210 .type = RTE_FLOW_ITEM_TYPE_TCP,
211 .rss_types = ETH_RSS_NONFRAG_IPV4_TCP,
213 [MLX5_EXPANSION_IPV6] = {
214 .next = RTE_FLOW_EXPAND_RSS_NEXT(MLX5_EXPANSION_IPV6_UDP,
215 MLX5_EXPANSION_IPV6_TCP),
216 .type = RTE_FLOW_ITEM_TYPE_IPV6,
217 .rss_types = ETH_RSS_IPV6 | ETH_RSS_FRAG_IPV6 |
218 ETH_RSS_NONFRAG_IPV6_OTHER,
220 [MLX5_EXPANSION_IPV6_UDP] = {
221 .type = RTE_FLOW_ITEM_TYPE_UDP,
222 .rss_types = ETH_RSS_NONFRAG_IPV6_UDP,
224 [MLX5_EXPANSION_IPV6_TCP] = {
225 .type = RTE_FLOW_ITEM_TYPE_TCP,
226 .rss_types = ETH_RSS_NONFRAG_IPV6_TCP,
230 static const struct rte_flow_ops mlx5_flow_ops = {
231 .validate = mlx5_flow_validate,
232 .create = mlx5_flow_create,
233 .destroy = mlx5_flow_destroy,
234 .flush = mlx5_flow_flush,
235 .isolate = mlx5_flow_isolate,
236 .query = mlx5_flow_query,
239 /* Convert FDIR request to Generic flow. */
241 struct rte_flow_attr attr;
242 struct rte_flow_item items[4];
243 struct rte_flow_item_eth l2;
244 struct rte_flow_item_eth l2_mask;
246 struct rte_flow_item_ipv4 ipv4;
247 struct rte_flow_item_ipv6 ipv6;
250 struct rte_flow_item_ipv4 ipv4;
251 struct rte_flow_item_ipv6 ipv6;
254 struct rte_flow_item_udp udp;
255 struct rte_flow_item_tcp tcp;
258 struct rte_flow_item_udp udp;
259 struct rte_flow_item_tcp tcp;
261 struct rte_flow_action actions[2];
262 struct rte_flow_action_queue queue;
265 /* Map of Verbs to Flow priority with 8 Verbs priorities. */
266 static const uint32_t priority_map_3[][MLX5_PRIORITY_MAP_MAX] = {
267 { 0, 1, 2 }, { 2, 3, 4 }, { 5, 6, 7 },
270 /* Map of Verbs to Flow priority with 16 Verbs priorities. */
271 static const uint32_t priority_map_5[][MLX5_PRIORITY_MAP_MAX] = {
272 { 0, 1, 2 }, { 3, 4, 5 }, { 6, 7, 8 },
273 { 9, 10, 11 }, { 12, 13, 14 },
276 /* Tunnel information. */
277 struct mlx5_flow_tunnel_info {
278 uint64_t tunnel; /**< Tunnel bit (see MLX5_FLOW_*). */
279 uint32_t ptype; /**< Tunnel Ptype (see RTE_PTYPE_*). */
282 static struct mlx5_flow_tunnel_info tunnels_info[] = {
284 .tunnel = MLX5_FLOW_LAYER_VXLAN,
285 .ptype = RTE_PTYPE_TUNNEL_VXLAN | RTE_PTYPE_L4_UDP,
288 .tunnel = MLX5_FLOW_LAYER_VXLAN_GPE,
289 .ptype = RTE_PTYPE_TUNNEL_VXLAN_GPE | RTE_PTYPE_L4_UDP,
292 .tunnel = MLX5_FLOW_LAYER_GRE,
293 .ptype = RTE_PTYPE_TUNNEL_GRE,
296 .tunnel = MLX5_FLOW_LAYER_MPLS | MLX5_FLOW_LAYER_OUTER_L4_UDP,
297 .ptype = RTE_PTYPE_TUNNEL_MPLS_IN_GRE | RTE_PTYPE_L4_UDP,
300 .tunnel = MLX5_FLOW_LAYER_MPLS,
301 .ptype = RTE_PTYPE_TUNNEL_MPLS_IN_GRE,
306 * Discover the maximum number of priority available.
309 * Pointer to the Ethernet device structure.
312 * number of supported flow priority on success, a negative errno
313 * value otherwise and rte_errno is set.
316 mlx5_flow_discover_priorities(struct rte_eth_dev *dev)
319 struct ibv_flow_attr attr;
320 struct ibv_flow_spec_eth eth;
321 struct ibv_flow_spec_action_drop drop;
327 .type = IBV_FLOW_SPEC_ETH,
328 .size = sizeof(struct ibv_flow_spec_eth),
331 .size = sizeof(struct ibv_flow_spec_action_drop),
332 .type = IBV_FLOW_SPEC_ACTION_DROP,
335 struct ibv_flow *flow;
336 struct mlx5_hrxq *drop = mlx5_hrxq_drop_new(dev);
337 uint16_t vprio[] = { 8, 16 };
345 for (i = 0; i != RTE_DIM(vprio); i++) {
346 flow_attr.attr.priority = vprio[i] - 1;
347 flow = mlx5_glue->create_flow(drop->qp, &flow_attr.attr);
350 claim_zero(mlx5_glue->destroy_flow(flow));
355 priority = RTE_DIM(priority_map_3);
358 priority = RTE_DIM(priority_map_5);
363 "port %u verbs maximum priority: %d expected 8/16",
364 dev->data->port_id, vprio[i]);
367 mlx5_hrxq_drop_release(dev);
368 DRV_LOG(INFO, "port %u flow maximum priority: %d",
369 dev->data->port_id, priority);
374 * Adjust flow priority based on the highest layer and the request priority.
377 * Pointer to the Ethernet device structure.
378 * @param[in] priority
379 * The rule base priority.
380 * @param[in] subpriority
381 * The priority based on the items.
386 uint32_t mlx5_flow_adjust_priority(struct rte_eth_dev *dev, int32_t priority,
387 uint32_t subpriority)
390 struct priv *priv = dev->data->dev_private;
392 switch (priv->config.flow_prio) {
393 case RTE_DIM(priority_map_3):
394 res = priority_map_3[priority][subpriority];
396 case RTE_DIM(priority_map_5):
397 res = priority_map_5[priority][subpriority];
404 * Verify the @p item specifications (spec, last, mask) are compatible with the
408 * Item specification.
410 * @p item->mask or flow default bit-masks.
411 * @param[in] nic_mask
412 * Bit-masks covering supported fields by the NIC to compare with user mask.
414 * Bit-masks size in bytes.
416 * Pointer to error structure.
419 * 0 on success, a negative errno value otherwise and rte_errno is set.
422 mlx5_flow_item_acceptable(const struct rte_flow_item *item,
424 const uint8_t *nic_mask,
426 struct rte_flow_error *error)
431 for (i = 0; i < size; ++i)
432 if ((nic_mask[i] | mask[i]) != nic_mask[i])
433 return rte_flow_error_set(error, ENOTSUP,
434 RTE_FLOW_ERROR_TYPE_ITEM,
436 "mask enables non supported"
438 if (!item->spec && (item->mask || item->last))
439 return rte_flow_error_set(error, EINVAL,
440 RTE_FLOW_ERROR_TYPE_ITEM, item,
441 "mask/last without a spec is not"
443 if (item->spec && item->last) {
449 for (i = 0; i < size; ++i) {
450 spec[i] = ((const uint8_t *)item->spec)[i] & mask[i];
451 last[i] = ((const uint8_t *)item->last)[i] & mask[i];
453 ret = memcmp(spec, last, size);
455 return rte_flow_error_set(error, EINVAL,
456 RTE_FLOW_ERROR_TYPE_ITEM,
458 "range is not valid");
464 * Adjust the hash fields according to the @p flow information.
466 * @param[in] dev_flow.
467 * Pointer to the mlx5_flow.
469 * 1 when the hash field is for a tunnel item.
470 * @param[in] layer_types
472 * @param[in] hash_fields
476 * The hash fileds that should be used.
479 mlx5_flow_hashfields_adjust(struct mlx5_flow *dev_flow,
480 int tunnel __rte_unused, uint64_t layer_types,
481 uint64_t hash_fields)
483 struct rte_flow *flow = dev_flow->flow;
484 #ifdef HAVE_IBV_DEVICE_TUNNEL_SUPPORT
485 int rss_request_inner = flow->rss.level >= 2;
487 /* Check RSS hash level for tunnel. */
488 if (tunnel && rss_request_inner)
489 hash_fields |= IBV_RX_HASH_INNER;
490 else if (tunnel || rss_request_inner)
493 /* Check if requested layer matches RSS hash fields. */
494 if (!(flow->rss.types & layer_types))
500 * Lookup and set the ptype in the data Rx part. A single Ptype can be used,
501 * if several tunnel rules are used on this queue, the tunnel ptype will be
505 * Rx queue to update.
508 flow_rxq_tunnel_ptype_update(struct mlx5_rxq_ctrl *rxq_ctrl)
511 uint32_t tunnel_ptype = 0;
513 /* Look up for the ptype to use. */
514 for (i = 0; i != MLX5_FLOW_TUNNEL; ++i) {
515 if (!rxq_ctrl->flow_tunnels_n[i])
518 tunnel_ptype = tunnels_info[i].ptype;
524 rxq_ctrl->rxq.tunnel = tunnel_ptype;
528 * Set the Rx queue flags (Mark/Flag and Tunnel Ptypes) according to the devive
532 * Pointer to the Ethernet device structure.
533 * @param[in] dev_flow
534 * Pointer to device flow structure.
537 flow_drv_rxq_flags_set(struct rte_eth_dev *dev, struct mlx5_flow *dev_flow)
539 struct priv *priv = dev->data->dev_private;
540 struct rte_flow *flow = dev_flow->flow;
541 const int mark = !!(flow->actions &
542 (MLX5_FLOW_ACTION_FLAG | MLX5_FLOW_ACTION_MARK));
543 const int tunnel = !!(dev_flow->layers & MLX5_FLOW_LAYER_TUNNEL);
546 for (i = 0; i != flow->rss.queue_num; ++i) {
547 int idx = (*flow->queue)[i];
548 struct mlx5_rxq_ctrl *rxq_ctrl =
549 container_of((*priv->rxqs)[idx],
550 struct mlx5_rxq_ctrl, rxq);
553 rxq_ctrl->rxq.mark = 1;
554 rxq_ctrl->flow_mark_n++;
559 /* Increase the counter matching the flow. */
560 for (j = 0; j != MLX5_FLOW_TUNNEL; ++j) {
561 if ((tunnels_info[j].tunnel &
563 tunnels_info[j].tunnel) {
564 rxq_ctrl->flow_tunnels_n[j]++;
568 flow_rxq_tunnel_ptype_update(rxq_ctrl);
574 * Set the Rx queue flags (Mark/Flag and Tunnel Ptypes) for a flow
577 * Pointer to the Ethernet device structure.
579 * Pointer to flow structure.
582 flow_rxq_flags_set(struct rte_eth_dev *dev, struct rte_flow *flow)
584 struct mlx5_flow *dev_flow;
586 LIST_FOREACH(dev_flow, &flow->dev_flows, next)
587 flow_drv_rxq_flags_set(dev, dev_flow);
591 * Clear the Rx queue flags (Mark/Flag and Tunnel Ptype) associated with the
592 * device flow if no other flow uses it with the same kind of request.
595 * Pointer to Ethernet device.
596 * @param[in] dev_flow
597 * Pointer to the device flow.
600 flow_drv_rxq_flags_trim(struct rte_eth_dev *dev, struct mlx5_flow *dev_flow)
602 struct priv *priv = dev->data->dev_private;
603 struct rte_flow *flow = dev_flow->flow;
604 const int mark = !!(flow->actions &
605 (MLX5_FLOW_ACTION_FLAG | MLX5_FLOW_ACTION_MARK));
606 const int tunnel = !!(dev_flow->layers & MLX5_FLOW_LAYER_TUNNEL);
609 assert(dev->data->dev_started);
610 for (i = 0; i != flow->rss.queue_num; ++i) {
611 int idx = (*flow->queue)[i];
612 struct mlx5_rxq_ctrl *rxq_ctrl =
613 container_of((*priv->rxqs)[idx],
614 struct mlx5_rxq_ctrl, rxq);
617 rxq_ctrl->flow_mark_n--;
618 rxq_ctrl->rxq.mark = !!rxq_ctrl->flow_mark_n;
623 /* Decrease the counter matching the flow. */
624 for (j = 0; j != MLX5_FLOW_TUNNEL; ++j) {
625 if ((tunnels_info[j].tunnel &
627 tunnels_info[j].tunnel) {
628 rxq_ctrl->flow_tunnels_n[j]--;
632 flow_rxq_tunnel_ptype_update(rxq_ctrl);
638 * Clear the Rx queue flags (Mark/Flag and Tunnel Ptype) associated with the
639 * @p flow if no other flow uses it with the same kind of request.
642 * Pointer to Ethernet device.
644 * Pointer to the flow.
647 flow_rxq_flags_trim(struct rte_eth_dev *dev, struct rte_flow *flow)
649 struct mlx5_flow *dev_flow;
651 LIST_FOREACH(dev_flow, &flow->dev_flows, next)
652 flow_drv_rxq_flags_trim(dev, dev_flow);
656 * Clear the Mark/Flag and Tunnel ptype information in all Rx queues.
659 * Pointer to Ethernet device.
662 flow_rxq_flags_clear(struct rte_eth_dev *dev)
664 struct priv *priv = dev->data->dev_private;
667 for (i = 0; i != priv->rxqs_n; ++i) {
668 struct mlx5_rxq_ctrl *rxq_ctrl;
671 if (!(*priv->rxqs)[i])
673 rxq_ctrl = container_of((*priv->rxqs)[i],
674 struct mlx5_rxq_ctrl, rxq);
675 rxq_ctrl->flow_mark_n = 0;
676 rxq_ctrl->rxq.mark = 0;
677 for (j = 0; j != MLX5_FLOW_TUNNEL; ++j)
678 rxq_ctrl->flow_tunnels_n[j] = 0;
679 rxq_ctrl->rxq.tunnel = 0;
684 * Validate the flag action.
686 * @param[in] action_flags
687 * Bit-fields that holds the actions detected until now.
689 * Attributes of flow that includes this action.
691 * Pointer to error structure.
694 * 0 on success, a negative errno value otherwise and rte_errno is set.
697 mlx5_flow_validate_action_flag(uint64_t action_flags,
698 const struct rte_flow_attr *attr,
699 struct rte_flow_error *error)
702 if (action_flags & MLX5_FLOW_ACTION_DROP)
703 return rte_flow_error_set(error, EINVAL,
704 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
705 "can't drop and flag in same flow");
706 if (action_flags & MLX5_FLOW_ACTION_MARK)
707 return rte_flow_error_set(error, EINVAL,
708 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
709 "can't mark and flag in same flow");
710 if (action_flags & MLX5_FLOW_ACTION_FLAG)
711 return rte_flow_error_set(error, EINVAL,
712 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
714 " actions in same flow");
716 return rte_flow_error_set(error, ENOTSUP,
717 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
718 "flag action not supported for "
724 * Validate the mark action.
727 * Pointer to the queue action.
728 * @param[in] action_flags
729 * Bit-fields that holds the actions detected until now.
731 * Attributes of flow that includes this action.
733 * Pointer to error structure.
736 * 0 on success, a negative errno value otherwise and rte_errno is set.
739 mlx5_flow_validate_action_mark(const struct rte_flow_action *action,
740 uint64_t action_flags,
741 const struct rte_flow_attr *attr,
742 struct rte_flow_error *error)
744 const struct rte_flow_action_mark *mark = action->conf;
747 return rte_flow_error_set(error, EINVAL,
748 RTE_FLOW_ERROR_TYPE_ACTION,
750 "configuration cannot be null");
751 if (mark->id >= MLX5_FLOW_MARK_MAX)
752 return rte_flow_error_set(error, EINVAL,
753 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
755 "mark id must in 0 <= id < "
756 RTE_STR(MLX5_FLOW_MARK_MAX));
757 if (action_flags & MLX5_FLOW_ACTION_DROP)
758 return rte_flow_error_set(error, EINVAL,
759 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
760 "can't drop and mark in same flow");
761 if (action_flags & MLX5_FLOW_ACTION_FLAG)
762 return rte_flow_error_set(error, EINVAL,
763 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
764 "can't flag and mark in same flow");
765 if (action_flags & MLX5_FLOW_ACTION_MARK)
766 return rte_flow_error_set(error, EINVAL,
767 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
768 "can't have 2 mark actions in same"
771 return rte_flow_error_set(error, ENOTSUP,
772 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
773 "mark action not supported for "
779 * Validate the drop action.
781 * @param[in] action_flags
782 * Bit-fields that holds the actions detected until now.
784 * Attributes of flow that includes this action.
786 * Pointer to error structure.
789 * 0 on success, a negative errno value otherwise and rte_ernno is set.
792 mlx5_flow_validate_action_drop(uint64_t action_flags,
793 const struct rte_flow_attr *attr,
794 struct rte_flow_error *error)
796 if (action_flags & MLX5_FLOW_ACTION_FLAG)
797 return rte_flow_error_set(error, EINVAL,
798 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
799 "can't drop and flag in same flow");
800 if (action_flags & MLX5_FLOW_ACTION_MARK)
801 return rte_flow_error_set(error, EINVAL,
802 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
803 "can't drop and mark in same flow");
804 if (action_flags & MLX5_FLOW_FATE_ACTIONS)
805 return rte_flow_error_set(error, EINVAL,
806 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
807 "can't have 2 fate actions in"
810 return rte_flow_error_set(error, ENOTSUP,
811 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
812 "drop action not supported for "
818 * Validate the queue action.
821 * Pointer to the queue action.
822 * @param[in] action_flags
823 * Bit-fields that holds the actions detected until now.
825 * Pointer to the Ethernet device structure.
827 * Attributes of flow that includes this action.
829 * Pointer to error structure.
832 * 0 on success, a negative errno value otherwise and rte_ernno is set.
835 mlx5_flow_validate_action_queue(const struct rte_flow_action *action,
836 uint64_t action_flags,
837 struct rte_eth_dev *dev,
838 const struct rte_flow_attr *attr,
839 struct rte_flow_error *error)
841 struct priv *priv = dev->data->dev_private;
842 const struct rte_flow_action_queue *queue = action->conf;
844 if (action_flags & MLX5_FLOW_FATE_ACTIONS)
845 return rte_flow_error_set(error, EINVAL,
846 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
847 "can't have 2 fate actions in"
849 if (queue->index >= priv->rxqs_n)
850 return rte_flow_error_set(error, EINVAL,
851 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
853 "queue index out of range");
854 if (!(*priv->rxqs)[queue->index])
855 return rte_flow_error_set(error, EINVAL,
856 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
858 "queue is not configured");
860 return rte_flow_error_set(error, ENOTSUP,
861 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
862 "queue action not supported for "
868 * Validate the rss action.
871 * Pointer to the queue action.
872 * @param[in] action_flags
873 * Bit-fields that holds the actions detected until now.
875 * Pointer to the Ethernet device structure.
877 * Attributes of flow that includes this action.
879 * Pointer to error structure.
882 * 0 on success, a negative errno value otherwise and rte_ernno is set.
885 mlx5_flow_validate_action_rss(const struct rte_flow_action *action,
886 uint64_t action_flags,
887 struct rte_eth_dev *dev,
888 const struct rte_flow_attr *attr,
889 struct rte_flow_error *error)
891 struct priv *priv = dev->data->dev_private;
892 const struct rte_flow_action_rss *rss = action->conf;
895 if (action_flags & MLX5_FLOW_FATE_ACTIONS)
896 return rte_flow_error_set(error, EINVAL,
897 RTE_FLOW_ERROR_TYPE_ACTION, NULL,
898 "can't have 2 fate actions"
900 if (rss->func != RTE_ETH_HASH_FUNCTION_DEFAULT &&
901 rss->func != RTE_ETH_HASH_FUNCTION_TOEPLITZ)
902 return rte_flow_error_set(error, ENOTSUP,
903 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
905 "RSS hash function not supported");
906 #ifdef HAVE_IBV_DEVICE_TUNNEL_SUPPORT
911 return rte_flow_error_set(error, ENOTSUP,
912 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
914 "tunnel RSS is not supported");
915 /* allow RSS key_len 0 in case of NULL (default) RSS key. */
916 if (rss->key_len == 0 && rss->key != NULL)
917 return rte_flow_error_set(error, ENOTSUP,
918 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
920 "RSS hash key length 0");
921 if (rss->key_len > 0 && rss->key_len < MLX5_RSS_HASH_KEY_LEN)
922 return rte_flow_error_set(error, ENOTSUP,
923 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
925 "RSS hash key too small");
926 if (rss->key_len > MLX5_RSS_HASH_KEY_LEN)
927 return rte_flow_error_set(error, ENOTSUP,
928 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
930 "RSS hash key too large");
931 if (rss->queue_num > priv->config.ind_table_max_size)
932 return rte_flow_error_set(error, ENOTSUP,
933 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
935 "number of queues too large");
936 if (rss->types & MLX5_RSS_HF_MASK)
937 return rte_flow_error_set(error, ENOTSUP,
938 RTE_FLOW_ERROR_TYPE_ACTION_CONF,
940 "some RSS protocols are not"
942 for (i = 0; i != rss->queue_num; ++i) {
943 if (!(*priv->rxqs)[rss->queue[i]])
944 return rte_flow_error_set
945 (error, EINVAL, RTE_FLOW_ERROR_TYPE_ACTION_CONF,
946 &rss->queue[i], "queue is not configured");
949 return rte_flow_error_set(error, ENOTSUP,
950 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
951 "rss action not supported for "
957 * Validate the count action.
960 * Pointer to the Ethernet device structure.
962 * Attributes of flow that includes this action.
964 * Pointer to error structure.
967 * 0 on success, a negative errno value otherwise and rte_ernno is set.
970 mlx5_flow_validate_action_count(struct rte_eth_dev *dev __rte_unused,
971 const struct rte_flow_attr *attr,
972 struct rte_flow_error *error)
975 return rte_flow_error_set(error, ENOTSUP,
976 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
977 "count action not supported for "
983 * Verify the @p attributes will be correctly understood by the NIC and store
984 * them in the @p flow if everything is correct.
987 * Pointer to the Ethernet device structure.
988 * @param[in] attributes
989 * Pointer to flow attributes
991 * Pointer to error structure.
994 * 0 on success, a negative errno value otherwise and rte_errno is set.
997 mlx5_flow_validate_attributes(struct rte_eth_dev *dev,
998 const struct rte_flow_attr *attributes,
999 struct rte_flow_error *error)
1001 struct priv *priv = dev->data->dev_private;
1002 uint32_t priority_max = priv->config.flow_prio - 1;
1004 if (attributes->group)
1005 return rte_flow_error_set(error, ENOTSUP,
1006 RTE_FLOW_ERROR_TYPE_ATTR_GROUP,
1007 NULL, "groups is not supported");
1008 if (attributes->priority != MLX5_FLOW_PRIO_RSVD &&
1009 attributes->priority >= priority_max)
1010 return rte_flow_error_set(error, ENOTSUP,
1011 RTE_FLOW_ERROR_TYPE_ATTR_PRIORITY,
1012 NULL, "priority out of range");
1013 if (attributes->egress)
1014 return rte_flow_error_set(error, ENOTSUP,
1015 RTE_FLOW_ERROR_TYPE_ATTR_EGRESS, NULL,
1016 "egress is not supported");
1017 if (attributes->transfer)
1018 return rte_flow_error_set(error, ENOTSUP,
1019 RTE_FLOW_ERROR_TYPE_ATTR_TRANSFER,
1020 NULL, "transfer is not supported");
1021 if (!attributes->ingress)
1022 return rte_flow_error_set(error, EINVAL,
1023 RTE_FLOW_ERROR_TYPE_ATTR_INGRESS,
1025 "ingress attribute is mandatory");
1030 * Validate Ethernet item.
1033 * Item specification.
1034 * @param[in] item_flags
1035 * Bit-fields that holds the items detected until now.
1037 * Pointer to error structure.
1040 * 0 on success, a negative errno value otherwise and rte_errno is set.
1043 mlx5_flow_validate_item_eth(const struct rte_flow_item *item,
1044 uint64_t item_flags,
1045 struct rte_flow_error *error)
1047 const struct rte_flow_item_eth *mask = item->mask;
1048 const struct rte_flow_item_eth nic_mask = {
1049 .dst.addr_bytes = "\xff\xff\xff\xff\xff\xff",
1050 .src.addr_bytes = "\xff\xff\xff\xff\xff\xff",
1051 .type = RTE_BE16(0xffff),
1054 int tunnel = !!(item_flags & MLX5_FLOW_LAYER_TUNNEL);
1055 const uint64_t ethm = tunnel ? MLX5_FLOW_LAYER_INNER_L2 :
1056 MLX5_FLOW_LAYER_OUTER_L2;
1058 if (item_flags & ethm)
1059 return rte_flow_error_set(error, ENOTSUP,
1060 RTE_FLOW_ERROR_TYPE_ITEM, item,
1061 "multiple L2 layers not supported");
1063 mask = &rte_flow_item_eth_mask;
1064 ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
1065 (const uint8_t *)&nic_mask,
1066 sizeof(struct rte_flow_item_eth),
1072 * Validate VLAN item.
1075 * Item specification.
1076 * @param[in] item_flags
1077 * Bit-fields that holds the items detected until now.
1079 * Pointer to error structure.
1082 * 0 on success, a negative errno value otherwise and rte_errno is set.
1085 mlx5_flow_validate_item_vlan(const struct rte_flow_item *item,
1086 uint64_t item_flags,
1087 struct rte_flow_error *error)
1089 const struct rte_flow_item_vlan *spec = item->spec;
1090 const struct rte_flow_item_vlan *mask = item->mask;
1091 const struct rte_flow_item_vlan nic_mask = {
1092 .tci = RTE_BE16(0x0fff),
1093 .inner_type = RTE_BE16(0xffff),
1095 uint16_t vlan_tag = 0;
1096 const int tunnel = !!(item_flags & MLX5_FLOW_LAYER_TUNNEL);
1098 const uint64_t l34m = tunnel ? (MLX5_FLOW_LAYER_INNER_L3 |
1099 MLX5_FLOW_LAYER_INNER_L4) :
1100 (MLX5_FLOW_LAYER_OUTER_L3 |
1101 MLX5_FLOW_LAYER_OUTER_L4);
1102 const uint64_t vlanm = tunnel ? MLX5_FLOW_LAYER_INNER_VLAN :
1103 MLX5_FLOW_LAYER_OUTER_VLAN;
1105 if (item_flags & vlanm)
1106 return rte_flow_error_set(error, EINVAL,
1107 RTE_FLOW_ERROR_TYPE_ITEM, item,
1108 "multiple VLAN layers not supported");
1109 else if ((item_flags & l34m) != 0)
1110 return rte_flow_error_set(error, EINVAL,
1111 RTE_FLOW_ERROR_TYPE_ITEM, item,
1112 "L2 layer cannot follow L3/L4 layer");
1114 mask = &rte_flow_item_vlan_mask;
1115 ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
1116 (const uint8_t *)&nic_mask,
1117 sizeof(struct rte_flow_item_vlan),
1122 vlan_tag = spec->tci;
1123 vlan_tag &= mask->tci;
1126 * From verbs perspective an empty VLAN is equivalent
1127 * to a packet without VLAN layer.
1130 return rte_flow_error_set(error, EINVAL,
1131 RTE_FLOW_ERROR_TYPE_ITEM_SPEC,
1133 "VLAN cannot be empty");
1138 * Validate IPV4 item.
1141 * Item specification.
1142 * @param[in] item_flags
1143 * Bit-fields that holds the items detected until now.
1145 * Pointer to error structure.
1148 * 0 on success, a negative errno value otherwise and rte_errno is set.
1151 mlx5_flow_validate_item_ipv4(const struct rte_flow_item *item,
1152 uint64_t item_flags,
1153 struct rte_flow_error *error)
1155 const struct rte_flow_item_ipv4 *mask = item->mask;
1156 const struct rte_flow_item_ipv4 nic_mask = {
1158 .src_addr = RTE_BE32(0xffffffff),
1159 .dst_addr = RTE_BE32(0xffffffff),
1160 .type_of_service = 0xff,
1161 .next_proto_id = 0xff,
1164 const int tunnel = !!(item_flags & MLX5_FLOW_LAYER_TUNNEL);
1165 const uint64_t l3m = tunnel ? MLX5_FLOW_LAYER_INNER_L3 :
1166 MLX5_FLOW_LAYER_OUTER_L3;
1167 const uint64_t l4m = tunnel ? MLX5_FLOW_LAYER_INNER_L4 :
1168 MLX5_FLOW_LAYER_OUTER_L4;
1171 if (item_flags & l3m)
1172 return rte_flow_error_set(error, ENOTSUP,
1173 RTE_FLOW_ERROR_TYPE_ITEM, item,
1174 "multiple L3 layers not supported");
1175 else if (item_flags & l4m)
1176 return rte_flow_error_set(error, EINVAL,
1177 RTE_FLOW_ERROR_TYPE_ITEM, item,
1178 "L3 cannot follow an L4 layer.");
1180 mask = &rte_flow_item_ipv4_mask;
1181 else if (mask->hdr.next_proto_id != 0 &&
1182 mask->hdr.next_proto_id != 0xff)
1183 return rte_flow_error_set(error, EINVAL,
1184 RTE_FLOW_ERROR_TYPE_ITEM_MASK, mask,
1185 "partial mask is not supported"
1187 ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
1188 (const uint8_t *)&nic_mask,
1189 sizeof(struct rte_flow_item_ipv4),
1197 * Validate IPV6 item.
1200 * Item specification.
1201 * @param[in] item_flags
1202 * Bit-fields that holds the items detected until now.
1204 * Pointer to error structure.
1207 * 0 on success, a negative errno value otherwise and rte_errno is set.
1210 mlx5_flow_validate_item_ipv6(const struct rte_flow_item *item,
1211 uint64_t item_flags,
1212 struct rte_flow_error *error)
1214 const struct rte_flow_item_ipv6 *mask = item->mask;
1215 const struct rte_flow_item_ipv6 nic_mask = {
1218 "\xff\xff\xff\xff\xff\xff\xff\xff"
1219 "\xff\xff\xff\xff\xff\xff\xff\xff",
1221 "\xff\xff\xff\xff\xff\xff\xff\xff"
1222 "\xff\xff\xff\xff\xff\xff\xff\xff",
1223 .vtc_flow = RTE_BE32(0xffffffff),
1228 const int tunnel = !!(item_flags & MLX5_FLOW_LAYER_TUNNEL);
1229 const uint64_t l3m = tunnel ? MLX5_FLOW_LAYER_INNER_L3 :
1230 MLX5_FLOW_LAYER_OUTER_L3;
1231 const uint64_t l4m = tunnel ? MLX5_FLOW_LAYER_INNER_L4 :
1232 MLX5_FLOW_LAYER_OUTER_L4;
1235 if (item_flags & l3m)
1236 return rte_flow_error_set(error, ENOTSUP,
1237 RTE_FLOW_ERROR_TYPE_ITEM, item,
1238 "multiple L3 layers not supported");
1239 else if (item_flags & l4m)
1240 return rte_flow_error_set(error, EINVAL,
1241 RTE_FLOW_ERROR_TYPE_ITEM, item,
1242 "L3 cannot follow an L4 layer.");
1244 mask = &rte_flow_item_ipv6_mask;
1245 ret = mlx5_flow_item_acceptable(item, (const uint8_t *)mask,
1246 (const uint8_t *)&nic_mask,
1247 sizeof(struct rte_flow_item_ipv6),
1255 * Validate UDP item.
1258 * Item specification.
1259 * @param[in] item_flags
1260 * Bit-fields that holds the items detected until now.
1261 * @param[in] target_protocol
1262 * The next protocol in the previous item.
1263 * @param[in] flow_mask
1264 * mlx5 flow-specific (TCF, DV, verbs, etc.) supported header fields mask.
1266 * Pointer to error structure.
1269 * 0 on success, a negative errno value otherwise and rte_errno is set.
1272 mlx5_flow_validate_item_udp(const struct rte_flow_item *item,
1273 uint64_t item_flags,
1274 uint8_t target_protocol,
1275 struct rte_flow_error *error)
1277 const struct rte_flow_item_udp *mask = item->mask;
1278 const int tunnel = !!(item_flags & MLX5_FLOW_LAYER_TUNNEL);
1279 const uint64_t l3m = tunnel ? MLX5_FLOW_LAYER_INNER_L3 :
1280 MLX5_FLOW_LAYER_OUTER_L3;
1281 const uint64_t l4m = tunnel ? MLX5_FLOW_LAYER_INNER_L4 :
1282 MLX5_FLOW_LAYER_OUTER_L4;
1285 if (target_protocol != 0xff && target_protocol != IPPROTO_UDP)
1286 return rte_flow_error_set(error, EINVAL,
1287 RTE_FLOW_ERROR_TYPE_ITEM, item,
1288 "protocol filtering not compatible"
1290 if (!(item_flags & l3m))
1291 return rte_flow_error_set(error, EINVAL,
1292 RTE_FLOW_ERROR_TYPE_ITEM, item,
1293 "L3 is mandatory to filter on L4");
1294 if (item_flags & l4m)
1295 return rte_flow_error_set(error, EINVAL,
1296 RTE_FLOW_ERROR_TYPE_ITEM, item,
1297 "multiple L4 layers not supported");
1299 mask = &rte_flow_item_udp_mask;
1300 ret = mlx5_flow_item_acceptable
1301 (item, (const uint8_t *)mask,
1302 (const uint8_t *)&rte_flow_item_udp_mask,
1303 sizeof(struct rte_flow_item_udp), error);
1310 * Validate TCP item.
1313 * Item specification.
1314 * @param[in] item_flags
1315 * Bit-fields that holds the items detected until now.
1316 * @param[in] target_protocol
1317 * The next protocol in the previous item.
1319 * Pointer to error structure.
1322 * 0 on success, a negative errno value otherwise and rte_errno is set.
1325 mlx5_flow_validate_item_tcp(const struct rte_flow_item *item,
1326 uint64_t item_flags,
1327 uint8_t target_protocol,
1328 const struct rte_flow_item_tcp *flow_mask,
1329 struct rte_flow_error *error)
1331 const struct rte_flow_item_tcp *mask = item->mask;
1332 const int tunnel = !!(item_flags & MLX5_FLOW_LAYER_TUNNEL);
1333 const uint64_t l3m = tunnel ? MLX5_FLOW_LAYER_INNER_L3 :
1334 MLX5_FLOW_LAYER_OUTER_L3;
1335 const uint64_t l4m = tunnel ? MLX5_FLOW_LAYER_INNER_L4 :
1336 MLX5_FLOW_LAYER_OUTER_L4;
1340 if (target_protocol != 0xff && target_protocol != IPPROTO_TCP)
1341 return rte_flow_error_set(error, EINVAL,
1342 RTE_FLOW_ERROR_TYPE_ITEM, item,
1343 "protocol filtering not compatible"
1345 if (!(item_flags & l3m))
1346 return rte_flow_error_set(error, EINVAL,
1347 RTE_FLOW_ERROR_TYPE_ITEM, item,
1348 "L3 is mandatory to filter on L4");
1349 if (item_flags & l4m)
1350 return rte_flow_error_set(error, EINVAL,
1351 RTE_FLOW_ERROR_TYPE_ITEM, item,
1352 "multiple L4 layers not supported");
1354 mask = &rte_flow_item_tcp_mask;
1355 ret = mlx5_flow_item_acceptable
1356 (item, (const uint8_t *)mask,
1357 (const uint8_t *)flow_mask,
1358 sizeof(struct rte_flow_item_tcp), error);
1365 * Validate VXLAN item.
1368 * Item specification.
1369 * @param[in] item_flags
1370 * Bit-fields that holds the items detected until now.
1371 * @param[in] target_protocol
1372 * The next protocol in the previous item.
1374 * Pointer to error structure.
1377 * 0 on success, a negative errno value otherwise and rte_errno is set.
1380 mlx5_flow_validate_item_vxlan(const struct rte_flow_item *item,
1381 uint64_t item_flags,
1382 struct rte_flow_error *error)
1384 const struct rte_flow_item_vxlan *spec = item->spec;
1385 const struct rte_flow_item_vxlan *mask = item->mask;
1390 } id = { .vlan_id = 0, };
1391 uint32_t vlan_id = 0;
1394 if (item_flags & MLX5_FLOW_LAYER_TUNNEL)
1395 return rte_flow_error_set(error, ENOTSUP,
1396 RTE_FLOW_ERROR_TYPE_ITEM, item,
1397 "multiple tunnel layers not"
1400 * Verify only UDPv4 is present as defined in
1401 * https://tools.ietf.org/html/rfc7348
1403 if (!(item_flags & MLX5_FLOW_LAYER_OUTER_L4_UDP))
1404 return rte_flow_error_set(error, EINVAL,
1405 RTE_FLOW_ERROR_TYPE_ITEM, item,
1406 "no outer UDP layer found");
1408 mask = &rte_flow_item_vxlan_mask;
1409 ret = mlx5_flow_item_acceptable
1410 (item, (const uint8_t *)mask,
1411 (const uint8_t *)&rte_flow_item_vxlan_mask,
1412 sizeof(struct rte_flow_item_vxlan),
1417 memcpy(&id.vni[1], spec->vni, 3);
1418 vlan_id = id.vlan_id;
1419 memcpy(&id.vni[1], mask->vni, 3);
1420 vlan_id &= id.vlan_id;
1423 * Tunnel id 0 is equivalent as not adding a VXLAN layer, if
1424 * only this layer is defined in the Verbs specification it is
1425 * interpreted as wildcard and all packets will match this
1426 * rule, if it follows a full stack layer (ex: eth / ipv4 /
1427 * udp), all packets matching the layers before will also
1428 * match this rule. To avoid such situation, VNI 0 is
1429 * currently refused.
1432 return rte_flow_error_set(error, ENOTSUP,
1433 RTE_FLOW_ERROR_TYPE_ITEM, item,
1434 "VXLAN vni cannot be 0");
1435 if (!(item_flags & MLX5_FLOW_LAYER_OUTER))
1436 return rte_flow_error_set(error, ENOTSUP,
1437 RTE_FLOW_ERROR_TYPE_ITEM, item,
1438 "VXLAN tunnel must be fully defined");
1443 * Validate VXLAN_GPE item.
1446 * Item specification.
1447 * @param[in] item_flags
1448 * Bit-fields that holds the items detected until now.
1450 * Pointer to the private data structure.
1451 * @param[in] target_protocol
1452 * The next protocol in the previous item.
1454 * Pointer to error structure.
1457 * 0 on success, a negative errno value otherwise and rte_errno is set.
1460 mlx5_flow_validate_item_vxlan_gpe(const struct rte_flow_item *item,
1461 uint64_t item_flags,
1462 struct rte_eth_dev *dev,
1463 struct rte_flow_error *error)
1465 struct priv *priv = dev->data->dev_private;
1466 const struct rte_flow_item_vxlan_gpe *spec = item->spec;
1467 const struct rte_flow_item_vxlan_gpe *mask = item->mask;
1472 } id = { .vlan_id = 0, };
1473 uint32_t vlan_id = 0;
1475 if (!priv->config.l3_vxlan_en)
1476 return rte_flow_error_set(error, ENOTSUP,
1477 RTE_FLOW_ERROR_TYPE_ITEM, item,
1478 "L3 VXLAN is not enabled by device"
1479 " parameter and/or not configured in"
1481 if (item_flags & MLX5_FLOW_LAYER_TUNNEL)
1482 return rte_flow_error_set(error, ENOTSUP,
1483 RTE_FLOW_ERROR_TYPE_ITEM, item,
1484 "multiple tunnel layers not"
1487 * Verify only UDPv4 is present as defined in
1488 * https://tools.ietf.org/html/rfc7348
1490 if (!(item_flags & MLX5_FLOW_LAYER_OUTER_L4_UDP))
1491 return rte_flow_error_set(error, EINVAL,
1492 RTE_FLOW_ERROR_TYPE_ITEM, item,
1493 "no outer UDP layer found");
1495 mask = &rte_flow_item_vxlan_gpe_mask;
1496 ret = mlx5_flow_item_acceptable
1497 (item, (const uint8_t *)mask,
1498 (const uint8_t *)&rte_flow_item_vxlan_gpe_mask,
1499 sizeof(struct rte_flow_item_vxlan_gpe),
1505 return rte_flow_error_set(error, ENOTSUP,
1506 RTE_FLOW_ERROR_TYPE_ITEM,
1508 "VxLAN-GPE protocol"
1510 memcpy(&id.vni[1], spec->vni, 3);
1511 vlan_id = id.vlan_id;
1512 memcpy(&id.vni[1], mask->vni, 3);
1513 vlan_id &= id.vlan_id;
1516 * Tunnel id 0 is equivalent as not adding a VXLAN layer, if only this
1517 * layer is defined in the Verbs specification it is interpreted as
1518 * wildcard and all packets will match this rule, if it follows a full
1519 * stack layer (ex: eth / ipv4 / udp), all packets matching the layers
1520 * before will also match this rule. To avoid such situation, VNI 0
1521 * is currently refused.
1524 return rte_flow_error_set(error, ENOTSUP,
1525 RTE_FLOW_ERROR_TYPE_ITEM, item,
1526 "VXLAN-GPE vni cannot be 0");
1527 if (!(item_flags & MLX5_FLOW_LAYER_OUTER))
1528 return rte_flow_error_set(error, ENOTSUP,
1529 RTE_FLOW_ERROR_TYPE_ITEM, item,
1530 "VXLAN-GPE tunnel must be fully"
1536 * Validate GRE item.
1539 * Item specification.
1540 * @param[in] item_flags
1541 * Bit flags to mark detected items.
1542 * @param[in] target_protocol
1543 * The next protocol in the previous item.
1545 * Pointer to error structure.
1548 * 0 on success, a negative errno value otherwise and rte_errno is set.
1551 mlx5_flow_validate_item_gre(const struct rte_flow_item *item,
1552 uint64_t item_flags,
1553 uint8_t target_protocol,
1554 struct rte_flow_error *error)
1556 const struct rte_flow_item_gre *spec __rte_unused = item->spec;
1557 const struct rte_flow_item_gre *mask = item->mask;
1560 if (target_protocol != 0xff && target_protocol != IPPROTO_GRE)
1561 return rte_flow_error_set(error, EINVAL,
1562 RTE_FLOW_ERROR_TYPE_ITEM, item,
1563 "protocol filtering not compatible"
1564 " with this GRE layer");
1565 if (item_flags & MLX5_FLOW_LAYER_TUNNEL)
1566 return rte_flow_error_set(error, ENOTSUP,
1567 RTE_FLOW_ERROR_TYPE_ITEM, item,
1568 "multiple tunnel layers not"
1570 if (!(item_flags & MLX5_FLOW_LAYER_OUTER_L3))
1571 return rte_flow_error_set(error, ENOTSUP,
1572 RTE_FLOW_ERROR_TYPE_ITEM, item,
1573 "L3 Layer is missing");
1575 mask = &rte_flow_item_gre_mask;
1576 ret = mlx5_flow_item_acceptable
1577 (item, (const uint8_t *)mask,
1578 (const uint8_t *)&rte_flow_item_gre_mask,
1579 sizeof(struct rte_flow_item_gre), error);
1582 #ifndef HAVE_IBV_DEVICE_MPLS_SUPPORT
1583 if (spec && (spec->protocol & mask->protocol))
1584 return rte_flow_error_set(error, ENOTSUP,
1585 RTE_FLOW_ERROR_TYPE_ITEM, item,
1586 "without MPLS support the"
1587 " specification cannot be used for"
1594 * Validate MPLS item.
1597 * Item specification.
1598 * @param[in] item_flags
1599 * Bit-fields that holds the items detected until now.
1600 * @param[in] target_protocol
1601 * The next protocol in the previous item.
1603 * Pointer to error structure.
1606 * 0 on success, a negative errno value otherwise and rte_errno is set.
1609 mlx5_flow_validate_item_mpls(const struct rte_flow_item *item __rte_unused,
1610 uint64_t item_flags __rte_unused,
1611 uint8_t target_protocol __rte_unused,
1612 struct rte_flow_error *error)
1614 #ifdef HAVE_IBV_DEVICE_MPLS_SUPPORT
1615 const struct rte_flow_item_mpls *mask = item->mask;
1618 if (target_protocol != 0xff && target_protocol != IPPROTO_MPLS)
1619 return rte_flow_error_set(error, EINVAL,
1620 RTE_FLOW_ERROR_TYPE_ITEM, item,
1621 "protocol filtering not compatible"
1622 " with MPLS layer");
1623 /* Multi-tunnel isn't allowed but MPLS over GRE is an exception. */
1624 if ((item_flags & MLX5_FLOW_LAYER_TUNNEL) &&
1625 !(item_flags & MLX5_FLOW_LAYER_GRE))
1626 return rte_flow_error_set(error, ENOTSUP,
1627 RTE_FLOW_ERROR_TYPE_ITEM, item,
1628 "multiple tunnel layers not"
1631 mask = &rte_flow_item_mpls_mask;
1632 ret = mlx5_flow_item_acceptable
1633 (item, (const uint8_t *)mask,
1634 (const uint8_t *)&rte_flow_item_mpls_mask,
1635 sizeof(struct rte_flow_item_mpls), error);
1640 return rte_flow_error_set(error, ENOTSUP,
1641 RTE_FLOW_ERROR_TYPE_ITEM, item,
1642 "MPLS is not supported by Verbs, please"
1647 flow_null_validate(struct rte_eth_dev *dev __rte_unused,
1648 const struct rte_flow_attr *attr __rte_unused,
1649 const struct rte_flow_item items[] __rte_unused,
1650 const struct rte_flow_action actions[] __rte_unused,
1651 struct rte_flow_error *error __rte_unused)
1653 rte_errno = ENOTSUP;
1657 static struct mlx5_flow *
1658 flow_null_prepare(const struct rte_flow_attr *attr __rte_unused,
1659 const struct rte_flow_item items[] __rte_unused,
1660 const struct rte_flow_action actions[] __rte_unused,
1661 struct rte_flow_error *error __rte_unused)
1663 rte_errno = ENOTSUP;
1668 flow_null_translate(struct rte_eth_dev *dev __rte_unused,
1669 struct mlx5_flow *dev_flow __rte_unused,
1670 const struct rte_flow_attr *attr __rte_unused,
1671 const struct rte_flow_item items[] __rte_unused,
1672 const struct rte_flow_action actions[] __rte_unused,
1673 struct rte_flow_error *error __rte_unused)
1675 rte_errno = ENOTSUP;
1680 flow_null_apply(struct rte_eth_dev *dev __rte_unused,
1681 struct rte_flow *flow __rte_unused,
1682 struct rte_flow_error *error __rte_unused)
1684 rte_errno = ENOTSUP;
1689 flow_null_remove(struct rte_eth_dev *dev __rte_unused,
1690 struct rte_flow *flow __rte_unused)
1695 flow_null_destroy(struct rte_eth_dev *dev __rte_unused,
1696 struct rte_flow *flow __rte_unused)
1701 flow_null_query(struct rte_eth_dev *dev __rte_unused,
1702 struct rte_flow *flow __rte_unused,
1703 const struct rte_flow_action *actions __rte_unused,
1704 void *data __rte_unused,
1705 struct rte_flow_error *error __rte_unused)
1707 rte_errno = ENOTSUP;
1711 /* Void driver to protect from null pointer reference. */
1712 const struct mlx5_flow_driver_ops mlx5_flow_null_drv_ops = {
1713 .validate = flow_null_validate,
1714 .prepare = flow_null_prepare,
1715 .translate = flow_null_translate,
1716 .apply = flow_null_apply,
1717 .remove = flow_null_remove,
1718 .destroy = flow_null_destroy,
1719 .query = flow_null_query,
1723 * Select flow driver type according to flow attributes and device
1727 * Pointer to the dev structure.
1729 * Pointer to the flow attributes.
1732 * flow driver type, MLX5_FLOW_TYPE_MAX otherwise.
1734 static enum mlx5_flow_drv_type
1735 flow_get_drv_type(struct rte_eth_dev *dev, const struct rte_flow_attr *attr)
1737 struct priv *priv = dev->data->dev_private;
1738 enum mlx5_flow_drv_type type = MLX5_FLOW_TYPE_MAX;
1741 type = MLX5_FLOW_TYPE_TCF;
1743 type = priv->config.dv_flow_en ? MLX5_FLOW_TYPE_DV :
1744 MLX5_FLOW_TYPE_VERBS;
1748 #define flow_get_drv_ops(type) flow_drv_ops[type]
1751 * Flow driver validation API. This abstracts calling driver specific functions.
1752 * The type of flow driver is determined according to flow attributes.
1755 * Pointer to the dev structure.
1757 * Pointer to the flow attributes.
1759 * Pointer to the list of items.
1760 * @param[in] actions
1761 * Pointer to the list of actions.
1763 * Pointer to the error structure.
1766 * 0 on success, a negative errno value otherwise and rte_ernno is set.
1769 flow_drv_validate(struct rte_eth_dev *dev,
1770 const struct rte_flow_attr *attr,
1771 const struct rte_flow_item items[],
1772 const struct rte_flow_action actions[],
1773 struct rte_flow_error *error)
1775 const struct mlx5_flow_driver_ops *fops;
1776 enum mlx5_flow_drv_type type = flow_get_drv_type(dev, attr);
1778 fops = flow_get_drv_ops(type);
1779 return fops->validate(dev, attr, items, actions, error);
1783 * Flow driver preparation API. This abstracts calling driver specific
1784 * functions. Parent flow (rte_flow) should have driver type (drv_type). It
1785 * calculates the size of memory required for device flow, allocates the memory,
1786 * initializes the device flow and returns the pointer.
1789 * This function initializes device flow structure such as dv, tcf or verbs in
1790 * struct mlx5_flow. However, it is caller's responsibility to initialize the
1791 * rest. For example, adding returning device flow to flow->dev_flow list and
1792 * setting backward reference to the flow should be done out of this function.
1793 * layers field is not filled either.
1796 * Pointer to the flow attributes.
1798 * Pointer to the list of items.
1799 * @param[in] actions
1800 * Pointer to the list of actions.
1802 * Pointer to the error structure.
1805 * Pointer to device flow on success, otherwise NULL and rte_ernno is set.
1807 static inline struct mlx5_flow *
1808 flow_drv_prepare(const struct rte_flow *flow,
1809 const struct rte_flow_attr *attr,
1810 const struct rte_flow_item items[],
1811 const struct rte_flow_action actions[],
1812 struct rte_flow_error *error)
1814 const struct mlx5_flow_driver_ops *fops;
1815 enum mlx5_flow_drv_type type = flow->drv_type;
1817 assert(type > MLX5_FLOW_TYPE_MIN && type < MLX5_FLOW_TYPE_MAX);
1818 fops = flow_get_drv_ops(type);
1819 return fops->prepare(attr, items, actions, error);
1823 * Flow driver translation API. This abstracts calling driver specific
1824 * functions. Parent flow (rte_flow) should have driver type (drv_type). It
1825 * translates a generic flow into a driver flow. flow_drv_prepare() must
1829 * dev_flow->layers could be filled as a result of parsing during translation
1830 * if needed by flow_drv_apply(). dev_flow->flow->actions can also be filled
1831 * if necessary. As a flow can have multiple dev_flows by RSS flow expansion,
1832 * flow->actions could be overwritten even though all the expanded dev_flows
1833 * have the same actions.
1836 * Pointer to the rte dev structure.
1837 * @param[in, out] dev_flow
1838 * Pointer to the mlx5 flow.
1840 * Pointer to the flow attributes.
1842 * Pointer to the list of items.
1843 * @param[in] actions
1844 * Pointer to the list of actions.
1846 * Pointer to the error structure.
1849 * 0 on success, a negative errno value otherwise and rte_ernno is set.
1852 flow_drv_translate(struct rte_eth_dev *dev, struct mlx5_flow *dev_flow,
1853 const struct rte_flow_attr *attr,
1854 const struct rte_flow_item items[],
1855 const struct rte_flow_action actions[],
1856 struct rte_flow_error *error)
1858 const struct mlx5_flow_driver_ops *fops;
1859 enum mlx5_flow_drv_type type = dev_flow->flow->drv_type;
1861 assert(type > MLX5_FLOW_TYPE_MIN && type < MLX5_FLOW_TYPE_MAX);
1862 fops = flow_get_drv_ops(type);
1863 return fops->translate(dev, dev_flow, attr, items, actions, error);
1867 * Flow driver apply API. This abstracts calling driver specific functions.
1868 * Parent flow (rte_flow) should have driver type (drv_type). It applies
1869 * translated driver flows on to device. flow_drv_translate() must precede.
1872 * Pointer to Ethernet device structure.
1873 * @param[in, out] flow
1874 * Pointer to flow structure.
1876 * Pointer to error structure.
1879 * 0 on success, a negative errno value otherwise and rte_errno is set.
1882 flow_drv_apply(struct rte_eth_dev *dev, struct rte_flow *flow,
1883 struct rte_flow_error *error)
1885 const struct mlx5_flow_driver_ops *fops;
1886 enum mlx5_flow_drv_type type = flow->drv_type;
1888 assert(type > MLX5_FLOW_TYPE_MIN && type < MLX5_FLOW_TYPE_MAX);
1889 fops = flow_get_drv_ops(type);
1890 return fops->apply(dev, flow, error);
1894 * Flow driver remove API. This abstracts calling driver specific functions.
1895 * Parent flow (rte_flow) should have driver type (drv_type). It removes a flow
1896 * on device. All the resources of the flow should be freed by calling
1897 * flow_drv_destroy().
1900 * Pointer to Ethernet device.
1901 * @param[in, out] flow
1902 * Pointer to flow structure.
1905 flow_drv_remove(struct rte_eth_dev *dev, struct rte_flow *flow)
1907 const struct mlx5_flow_driver_ops *fops;
1908 enum mlx5_flow_drv_type type = flow->drv_type;
1910 assert(type > MLX5_FLOW_TYPE_MIN && type < MLX5_FLOW_TYPE_MAX);
1911 fops = flow_get_drv_ops(type);
1912 fops->remove(dev, flow);
1916 * Flow driver destroy API. This abstracts calling driver specific functions.
1917 * Parent flow (rte_flow) should have driver type (drv_type). It removes a flow
1918 * on device and releases resources of the flow.
1921 * Pointer to Ethernet device.
1922 * @param[in, out] flow
1923 * Pointer to flow structure.
1926 flow_drv_destroy(struct rte_eth_dev *dev, struct rte_flow *flow)
1928 const struct mlx5_flow_driver_ops *fops;
1929 enum mlx5_flow_drv_type type = flow->drv_type;
1931 assert(type > MLX5_FLOW_TYPE_MIN && type < MLX5_FLOW_TYPE_MAX);
1932 fops = flow_get_drv_ops(type);
1933 fops->destroy(dev, flow);
1937 * Validate a flow supported by the NIC.
1939 * @see rte_flow_validate()
1943 mlx5_flow_validate(struct rte_eth_dev *dev,
1944 const struct rte_flow_attr *attr,
1945 const struct rte_flow_item items[],
1946 const struct rte_flow_action actions[],
1947 struct rte_flow_error *error)
1951 ret = flow_drv_validate(dev, attr, items, actions, error);
1958 * Get RSS action from the action list.
1960 * @param[in] actions
1961 * Pointer to the list of actions.
1964 * Pointer to the RSS action if exist, else return NULL.
1966 static const struct rte_flow_action_rss*
1967 flow_get_rss_action(const struct rte_flow_action actions[])
1969 for (; actions->type != RTE_FLOW_ACTION_TYPE_END; actions++) {
1970 switch (actions->type) {
1971 case RTE_FLOW_ACTION_TYPE_RSS:
1972 return (const struct rte_flow_action_rss *)
1982 find_graph_root(const struct rte_flow_item pattern[], uint32_t rss_level)
1984 const struct rte_flow_item *item;
1985 unsigned int has_vlan = 0;
1987 for (item = pattern; item->type != RTE_FLOW_ITEM_TYPE_END; item++) {
1988 if (item->type == RTE_FLOW_ITEM_TYPE_VLAN) {
1994 return rss_level < 2 ? MLX5_EXPANSION_ROOT_ETH_VLAN :
1995 MLX5_EXPANSION_ROOT_OUTER_ETH_VLAN;
1996 return rss_level < 2 ? MLX5_EXPANSION_ROOT :
1997 MLX5_EXPANSION_ROOT_OUTER;
2001 * Create a flow and add it to @p list.
2004 * Pointer to Ethernet device.
2006 * Pointer to a TAILQ flow list.
2008 * Flow rule attributes.
2010 * Pattern specification (list terminated by the END pattern item).
2011 * @param[in] actions
2012 * Associated actions (list terminated by the END action).
2014 * Perform verbose error reporting if not NULL.
2017 * A flow on success, NULL otherwise and rte_errno is set.
2019 static struct rte_flow *
2020 flow_list_create(struct rte_eth_dev *dev, struct mlx5_flows *list,
2021 const struct rte_flow_attr *attr,
2022 const struct rte_flow_item items[],
2023 const struct rte_flow_action actions[],
2024 struct rte_flow_error *error)
2026 struct rte_flow *flow = NULL;
2027 struct mlx5_flow *dev_flow;
2028 const struct rte_flow_action_rss *rss;
2030 struct rte_flow_expand_rss buf;
2031 uint8_t buffer[2048];
2033 struct rte_flow_expand_rss *buf = &expand_buffer.buf;
2038 ret = flow_drv_validate(dev, attr, items, actions, error);
2041 flow_size = sizeof(struct rte_flow);
2042 rss = flow_get_rss_action(actions);
2044 flow_size += RTE_ALIGN_CEIL(rss->queue_num * sizeof(uint16_t),
2047 flow_size += RTE_ALIGN_CEIL(sizeof(uint16_t), sizeof(void *));
2048 flow = rte_calloc(__func__, 1, flow_size, 0);
2049 flow->drv_type = flow_get_drv_type(dev, attr);
2050 assert(flow->drv_type > MLX5_FLOW_TYPE_MIN &&
2051 flow->drv_type < MLX5_FLOW_TYPE_MAX);
2052 flow->queue = (void *)(flow + 1);
2053 LIST_INIT(&flow->dev_flows);
2054 if (rss && rss->types) {
2055 unsigned int graph_root;
2057 graph_root = find_graph_root(items, rss->level);
2058 ret = rte_flow_expand_rss(buf, sizeof(expand_buffer.buffer),
2060 mlx5_support_expansion,
2063 (unsigned int)ret < sizeof(expand_buffer.buffer));
2066 buf->entry[0].pattern = (void *)(uintptr_t)items;
2068 for (i = 0; i < buf->entries; ++i) {
2069 dev_flow = flow_drv_prepare(flow, attr, buf->entry[i].pattern,
2073 dev_flow->flow = flow;
2074 LIST_INSERT_HEAD(&flow->dev_flows, dev_flow, next);
2075 ret = flow_drv_translate(dev, dev_flow, attr,
2076 buf->entry[i].pattern,
2081 if (dev->data->dev_started) {
2082 ret = flow_drv_apply(dev, flow, error);
2086 TAILQ_INSERT_TAIL(list, flow, next);
2087 flow_rxq_flags_set(dev, flow);
2090 ret = rte_errno; /* Save rte_errno before cleanup. */
2092 flow_drv_destroy(dev, flow);
2094 rte_errno = ret; /* Restore rte_errno. */
2101 * @see rte_flow_create()
2105 mlx5_flow_create(struct rte_eth_dev *dev,
2106 const struct rte_flow_attr *attr,
2107 const struct rte_flow_item items[],
2108 const struct rte_flow_action actions[],
2109 struct rte_flow_error *error)
2111 return flow_list_create(dev,
2112 &((struct priv *)dev->data->dev_private)->flows,
2113 attr, items, actions, error);
2117 * Destroy a flow in a list.
2120 * Pointer to Ethernet device.
2122 * Pointer to a TAILQ flow list.
2127 flow_list_destroy(struct rte_eth_dev *dev, struct mlx5_flows *list,
2128 struct rte_flow *flow)
2131 * Update RX queue flags only if port is started, otherwise it is
2134 if (dev->data->dev_started)
2135 flow_rxq_flags_trim(dev, flow);
2136 flow_drv_destroy(dev, flow);
2137 TAILQ_REMOVE(list, flow, next);
2138 rte_free(flow->fdir);
2143 * Destroy all flows.
2146 * Pointer to Ethernet device.
2148 * Pointer to a TAILQ flow list.
2151 mlx5_flow_list_flush(struct rte_eth_dev *dev, struct mlx5_flows *list)
2153 while (!TAILQ_EMPTY(list)) {
2154 struct rte_flow *flow;
2156 flow = TAILQ_FIRST(list);
2157 flow_list_destroy(dev, list, flow);
2165 * Pointer to Ethernet device.
2167 * Pointer to a TAILQ flow list.
2170 mlx5_flow_stop(struct rte_eth_dev *dev, struct mlx5_flows *list)
2172 struct rte_flow *flow;
2174 TAILQ_FOREACH_REVERSE(flow, list, mlx5_flows, next)
2175 flow_drv_remove(dev, flow);
2176 flow_rxq_flags_clear(dev);
2183 * Pointer to Ethernet device.
2185 * Pointer to a TAILQ flow list.
2188 * 0 on success, a negative errno value otherwise and rte_errno is set.
2191 mlx5_flow_start(struct rte_eth_dev *dev, struct mlx5_flows *list)
2193 struct rte_flow *flow;
2194 struct rte_flow_error error;
2197 TAILQ_FOREACH(flow, list, next) {
2198 ret = flow_drv_apply(dev, flow, &error);
2201 flow_rxq_flags_set(dev, flow);
2205 ret = rte_errno; /* Save rte_errno before cleanup. */
2206 mlx5_flow_stop(dev, list);
2207 rte_errno = ret; /* Restore rte_errno. */
2212 * Verify the flow list is empty
2215 * Pointer to Ethernet device.
2217 * @return the number of flows not released.
2220 mlx5_flow_verify(struct rte_eth_dev *dev)
2222 struct priv *priv = dev->data->dev_private;
2223 struct rte_flow *flow;
2226 TAILQ_FOREACH(flow, &priv->flows, next) {
2227 DRV_LOG(DEBUG, "port %u flow %p still referenced",
2228 dev->data->port_id, (void *)flow);
2235 * Enable a control flow configured from the control plane.
2238 * Pointer to Ethernet device.
2240 * An Ethernet flow spec to apply.
2242 * An Ethernet flow mask to apply.
2244 * A VLAN flow spec to apply.
2246 * A VLAN flow mask to apply.
2249 * 0 on success, a negative errno value otherwise and rte_errno is set.
2252 mlx5_ctrl_flow_vlan(struct rte_eth_dev *dev,
2253 struct rte_flow_item_eth *eth_spec,
2254 struct rte_flow_item_eth *eth_mask,
2255 struct rte_flow_item_vlan *vlan_spec,
2256 struct rte_flow_item_vlan *vlan_mask)
2258 struct priv *priv = dev->data->dev_private;
2259 const struct rte_flow_attr attr = {
2261 .priority = MLX5_FLOW_PRIO_RSVD,
2263 struct rte_flow_item items[] = {
2265 .type = RTE_FLOW_ITEM_TYPE_ETH,
2271 .type = (vlan_spec) ? RTE_FLOW_ITEM_TYPE_VLAN :
2272 RTE_FLOW_ITEM_TYPE_END,
2278 .type = RTE_FLOW_ITEM_TYPE_END,
2281 uint16_t queue[priv->reta_idx_n];
2282 struct rte_flow_action_rss action_rss = {
2283 .func = RTE_ETH_HASH_FUNCTION_DEFAULT,
2285 .types = priv->rss_conf.rss_hf,
2286 .key_len = priv->rss_conf.rss_key_len,
2287 .queue_num = priv->reta_idx_n,
2288 .key = priv->rss_conf.rss_key,
2291 struct rte_flow_action actions[] = {
2293 .type = RTE_FLOW_ACTION_TYPE_RSS,
2294 .conf = &action_rss,
2297 .type = RTE_FLOW_ACTION_TYPE_END,
2300 struct rte_flow *flow;
2301 struct rte_flow_error error;
2304 if (!priv->reta_idx_n) {
2308 for (i = 0; i != priv->reta_idx_n; ++i)
2309 queue[i] = (*priv->reta_idx)[i];
2310 flow = flow_list_create(dev, &priv->ctrl_flows,
2311 &attr, items, actions, &error);
2318 * Enable a flow control configured from the control plane.
2321 * Pointer to Ethernet device.
2323 * An Ethernet flow spec to apply.
2325 * An Ethernet flow mask to apply.
2328 * 0 on success, a negative errno value otherwise and rte_errno is set.
2331 mlx5_ctrl_flow(struct rte_eth_dev *dev,
2332 struct rte_flow_item_eth *eth_spec,
2333 struct rte_flow_item_eth *eth_mask)
2335 return mlx5_ctrl_flow_vlan(dev, eth_spec, eth_mask, NULL, NULL);
2341 * @see rte_flow_destroy()
2345 mlx5_flow_destroy(struct rte_eth_dev *dev,
2346 struct rte_flow *flow,
2347 struct rte_flow_error *error __rte_unused)
2349 struct priv *priv = dev->data->dev_private;
2351 flow_list_destroy(dev, &priv->flows, flow);
2356 * Destroy all flows.
2358 * @see rte_flow_flush()
2362 mlx5_flow_flush(struct rte_eth_dev *dev,
2363 struct rte_flow_error *error __rte_unused)
2365 struct priv *priv = dev->data->dev_private;
2367 mlx5_flow_list_flush(dev, &priv->flows);
2374 * @see rte_flow_isolate()
2378 mlx5_flow_isolate(struct rte_eth_dev *dev,
2380 struct rte_flow_error *error)
2382 struct priv *priv = dev->data->dev_private;
2384 if (dev->data->dev_started) {
2385 rte_flow_error_set(error, EBUSY,
2386 RTE_FLOW_ERROR_TYPE_UNSPECIFIED,
2388 "port must be stopped first");
2391 priv->isolated = !!enable;
2393 dev->dev_ops = &mlx5_dev_ops_isolate;
2395 dev->dev_ops = &mlx5_dev_ops;
2402 * @see rte_flow_query()
2406 flow_drv_query(struct rte_eth_dev *dev,
2407 struct rte_flow *flow,
2408 const struct rte_flow_action *actions,
2410 struct rte_flow_error *error)
2412 const struct mlx5_flow_driver_ops *fops;
2413 enum mlx5_flow_drv_type ftype = flow->drv_type;
2415 assert(ftype > MLX5_FLOW_TYPE_MIN && ftype < MLX5_FLOW_TYPE_MAX);
2416 fops = flow_get_drv_ops(ftype);
2418 return fops->query(dev, flow, actions, data, error);
2424 * @see rte_flow_query()
2428 mlx5_flow_query(struct rte_eth_dev *dev,
2429 struct rte_flow *flow,
2430 const struct rte_flow_action *actions,
2432 struct rte_flow_error *error)
2436 ret = flow_drv_query(dev, flow, actions, data, error);
2443 * Convert a flow director filter to a generic flow.
2446 * Pointer to Ethernet device.
2447 * @param fdir_filter
2448 * Flow director filter to add.
2450 * Generic flow parameters structure.
2453 * 0 on success, a negative errno value otherwise and rte_errno is set.
2456 flow_fdir_filter_convert(struct rte_eth_dev *dev,
2457 const struct rte_eth_fdir_filter *fdir_filter,
2458 struct mlx5_fdir *attributes)
2460 struct priv *priv = dev->data->dev_private;
2461 const struct rte_eth_fdir_input *input = &fdir_filter->input;
2462 const struct rte_eth_fdir_masks *mask =
2463 &dev->data->dev_conf.fdir_conf.mask;
2465 /* Validate queue number. */
2466 if (fdir_filter->action.rx_queue >= priv->rxqs_n) {
2467 DRV_LOG(ERR, "port %u invalid queue number %d",
2468 dev->data->port_id, fdir_filter->action.rx_queue);
2472 attributes->attr.ingress = 1;
2473 attributes->items[0] = (struct rte_flow_item) {
2474 .type = RTE_FLOW_ITEM_TYPE_ETH,
2475 .spec = &attributes->l2,
2476 .mask = &attributes->l2_mask,
2478 switch (fdir_filter->action.behavior) {
2479 case RTE_ETH_FDIR_ACCEPT:
2480 attributes->actions[0] = (struct rte_flow_action){
2481 .type = RTE_FLOW_ACTION_TYPE_QUEUE,
2482 .conf = &attributes->queue,
2485 case RTE_ETH_FDIR_REJECT:
2486 attributes->actions[0] = (struct rte_flow_action){
2487 .type = RTE_FLOW_ACTION_TYPE_DROP,
2491 DRV_LOG(ERR, "port %u invalid behavior %d",
2493 fdir_filter->action.behavior);
2494 rte_errno = ENOTSUP;
2497 attributes->queue.index = fdir_filter->action.rx_queue;
2499 switch (fdir_filter->input.flow_type) {
2500 case RTE_ETH_FLOW_NONFRAG_IPV4_UDP:
2501 case RTE_ETH_FLOW_NONFRAG_IPV4_TCP:
2502 case RTE_ETH_FLOW_NONFRAG_IPV4_OTHER:
2503 attributes->l3.ipv4.hdr = (struct ipv4_hdr){
2504 .src_addr = input->flow.ip4_flow.src_ip,
2505 .dst_addr = input->flow.ip4_flow.dst_ip,
2506 .time_to_live = input->flow.ip4_flow.ttl,
2507 .type_of_service = input->flow.ip4_flow.tos,
2509 attributes->l3_mask.ipv4.hdr = (struct ipv4_hdr){
2510 .src_addr = mask->ipv4_mask.src_ip,
2511 .dst_addr = mask->ipv4_mask.dst_ip,
2512 .time_to_live = mask->ipv4_mask.ttl,
2513 .type_of_service = mask->ipv4_mask.tos,
2514 .next_proto_id = mask->ipv4_mask.proto,
2516 attributes->items[1] = (struct rte_flow_item){
2517 .type = RTE_FLOW_ITEM_TYPE_IPV4,
2518 .spec = &attributes->l3,
2519 .mask = &attributes->l3_mask,
2522 case RTE_ETH_FLOW_NONFRAG_IPV6_UDP:
2523 case RTE_ETH_FLOW_NONFRAG_IPV6_TCP:
2524 case RTE_ETH_FLOW_NONFRAG_IPV6_OTHER:
2525 attributes->l3.ipv6.hdr = (struct ipv6_hdr){
2526 .hop_limits = input->flow.ipv6_flow.hop_limits,
2527 .proto = input->flow.ipv6_flow.proto,
2530 memcpy(attributes->l3.ipv6.hdr.src_addr,
2531 input->flow.ipv6_flow.src_ip,
2532 RTE_DIM(attributes->l3.ipv6.hdr.src_addr));
2533 memcpy(attributes->l3.ipv6.hdr.dst_addr,
2534 input->flow.ipv6_flow.dst_ip,
2535 RTE_DIM(attributes->l3.ipv6.hdr.src_addr));
2536 memcpy(attributes->l3_mask.ipv6.hdr.src_addr,
2537 mask->ipv6_mask.src_ip,
2538 RTE_DIM(attributes->l3_mask.ipv6.hdr.src_addr));
2539 memcpy(attributes->l3_mask.ipv6.hdr.dst_addr,
2540 mask->ipv6_mask.dst_ip,
2541 RTE_DIM(attributes->l3_mask.ipv6.hdr.src_addr));
2542 attributes->items[1] = (struct rte_flow_item){
2543 .type = RTE_FLOW_ITEM_TYPE_IPV6,
2544 .spec = &attributes->l3,
2545 .mask = &attributes->l3_mask,
2549 DRV_LOG(ERR, "port %u invalid flow type%d",
2550 dev->data->port_id, fdir_filter->input.flow_type);
2551 rte_errno = ENOTSUP;
2555 switch (fdir_filter->input.flow_type) {
2556 case RTE_ETH_FLOW_NONFRAG_IPV4_UDP:
2557 attributes->l4.udp.hdr = (struct udp_hdr){
2558 .src_port = input->flow.udp4_flow.src_port,
2559 .dst_port = input->flow.udp4_flow.dst_port,
2561 attributes->l4_mask.udp.hdr = (struct udp_hdr){
2562 .src_port = mask->src_port_mask,
2563 .dst_port = mask->dst_port_mask,
2565 attributes->items[2] = (struct rte_flow_item){
2566 .type = RTE_FLOW_ITEM_TYPE_UDP,
2567 .spec = &attributes->l4,
2568 .mask = &attributes->l4_mask,
2571 case RTE_ETH_FLOW_NONFRAG_IPV4_TCP:
2572 attributes->l4.tcp.hdr = (struct tcp_hdr){
2573 .src_port = input->flow.tcp4_flow.src_port,
2574 .dst_port = input->flow.tcp4_flow.dst_port,
2576 attributes->l4_mask.tcp.hdr = (struct tcp_hdr){
2577 .src_port = mask->src_port_mask,
2578 .dst_port = mask->dst_port_mask,
2580 attributes->items[2] = (struct rte_flow_item){
2581 .type = RTE_FLOW_ITEM_TYPE_TCP,
2582 .spec = &attributes->l4,
2583 .mask = &attributes->l4_mask,
2586 case RTE_ETH_FLOW_NONFRAG_IPV6_UDP:
2587 attributes->l4.udp.hdr = (struct udp_hdr){
2588 .src_port = input->flow.udp6_flow.src_port,
2589 .dst_port = input->flow.udp6_flow.dst_port,
2591 attributes->l4_mask.udp.hdr = (struct udp_hdr){
2592 .src_port = mask->src_port_mask,
2593 .dst_port = mask->dst_port_mask,
2595 attributes->items[2] = (struct rte_flow_item){
2596 .type = RTE_FLOW_ITEM_TYPE_UDP,
2597 .spec = &attributes->l4,
2598 .mask = &attributes->l4_mask,
2601 case RTE_ETH_FLOW_NONFRAG_IPV6_TCP:
2602 attributes->l4.tcp.hdr = (struct tcp_hdr){
2603 .src_port = input->flow.tcp6_flow.src_port,
2604 .dst_port = input->flow.tcp6_flow.dst_port,
2606 attributes->l4_mask.tcp.hdr = (struct tcp_hdr){
2607 .src_port = mask->src_port_mask,
2608 .dst_port = mask->dst_port_mask,
2610 attributes->items[2] = (struct rte_flow_item){
2611 .type = RTE_FLOW_ITEM_TYPE_TCP,
2612 .spec = &attributes->l4,
2613 .mask = &attributes->l4_mask,
2616 case RTE_ETH_FLOW_NONFRAG_IPV4_OTHER:
2617 case RTE_ETH_FLOW_NONFRAG_IPV6_OTHER:
2620 DRV_LOG(ERR, "port %u invalid flow type%d",
2621 dev->data->port_id, fdir_filter->input.flow_type);
2622 rte_errno = ENOTSUP;
2628 #define FLOW_FDIR_CMP(f1, f2, fld) \
2629 memcmp(&(f1)->fld, &(f2)->fld, sizeof(f1->fld))
2632 * Compare two FDIR flows. If items and actions are identical, the two flows are
2636 * Pointer to Ethernet device.
2638 * FDIR flow to compare.
2640 * FDIR flow to compare.
2643 * Zero on match, 1 otherwise.
2646 flow_fdir_cmp(const struct mlx5_fdir *f1, const struct mlx5_fdir *f2)
2648 if (FLOW_FDIR_CMP(f1, f2, attr) ||
2649 FLOW_FDIR_CMP(f1, f2, l2) ||
2650 FLOW_FDIR_CMP(f1, f2, l2_mask) ||
2651 FLOW_FDIR_CMP(f1, f2, l3) ||
2652 FLOW_FDIR_CMP(f1, f2, l3_mask) ||
2653 FLOW_FDIR_CMP(f1, f2, l4) ||
2654 FLOW_FDIR_CMP(f1, f2, l4_mask) ||
2655 FLOW_FDIR_CMP(f1, f2, actions[0].type))
2657 if (f1->actions[0].type == RTE_FLOW_ACTION_TYPE_QUEUE &&
2658 FLOW_FDIR_CMP(f1, f2, queue))
2664 * Search device flow list to find out a matched FDIR flow.
2667 * Pointer to Ethernet device.
2669 * FDIR flow to lookup.
2672 * Pointer of flow if found, NULL otherwise.
2674 static struct rte_flow *
2675 flow_fdir_filter_lookup(struct rte_eth_dev *dev, struct mlx5_fdir *fdir_flow)
2677 struct priv *priv = dev->data->dev_private;
2678 struct rte_flow *flow = NULL;
2681 TAILQ_FOREACH(flow, &priv->flows, next) {
2682 if (flow->fdir && !flow_fdir_cmp(flow->fdir, fdir_flow)) {
2683 DRV_LOG(DEBUG, "port %u found FDIR flow %p",
2684 dev->data->port_id, (void *)flow);
2692 * Add new flow director filter and store it in list.
2695 * Pointer to Ethernet device.
2696 * @param fdir_filter
2697 * Flow director filter to add.
2700 * 0 on success, a negative errno value otherwise and rte_errno is set.
2703 flow_fdir_filter_add(struct rte_eth_dev *dev,
2704 const struct rte_eth_fdir_filter *fdir_filter)
2706 struct priv *priv = dev->data->dev_private;
2707 struct mlx5_fdir *fdir_flow;
2708 struct rte_flow *flow;
2711 fdir_flow = rte_zmalloc(__func__, sizeof(*fdir_flow), 0);
2716 ret = flow_fdir_filter_convert(dev, fdir_filter, fdir_flow);
2719 flow = flow_fdir_filter_lookup(dev, fdir_flow);
2724 flow = flow_list_create(dev, &priv->flows, &fdir_flow->attr,
2725 fdir_flow->items, fdir_flow->actions, NULL);
2728 assert(!flow->fdir);
2729 flow->fdir = fdir_flow;
2730 DRV_LOG(DEBUG, "port %u created FDIR flow %p",
2731 dev->data->port_id, (void *)flow);
2734 rte_free(fdir_flow);
2739 * Delete specific filter.
2742 * Pointer to Ethernet device.
2743 * @param fdir_filter
2744 * Filter to be deleted.
2747 * 0 on success, a negative errno value otherwise and rte_errno is set.
2750 flow_fdir_filter_delete(struct rte_eth_dev *dev,
2751 const struct rte_eth_fdir_filter *fdir_filter)
2753 struct priv *priv = dev->data->dev_private;
2754 struct rte_flow *flow;
2755 struct mlx5_fdir fdir_flow = {
2760 ret = flow_fdir_filter_convert(dev, fdir_filter, &fdir_flow);
2763 flow = flow_fdir_filter_lookup(dev, &fdir_flow);
2768 flow_list_destroy(dev, &priv->flows, flow);
2769 DRV_LOG(DEBUG, "port %u deleted FDIR flow %p",
2770 dev->data->port_id, (void *)flow);
2775 * Update queue for specific filter.
2778 * Pointer to Ethernet device.
2779 * @param fdir_filter
2780 * Filter to be updated.
2783 * 0 on success, a negative errno value otherwise and rte_errno is set.
2786 flow_fdir_filter_update(struct rte_eth_dev *dev,
2787 const struct rte_eth_fdir_filter *fdir_filter)
2791 ret = flow_fdir_filter_delete(dev, fdir_filter);
2794 return flow_fdir_filter_add(dev, fdir_filter);
2798 * Flush all filters.
2801 * Pointer to Ethernet device.
2804 flow_fdir_filter_flush(struct rte_eth_dev *dev)
2806 struct priv *priv = dev->data->dev_private;
2808 mlx5_flow_list_flush(dev, &priv->flows);
2812 * Get flow director information.
2815 * Pointer to Ethernet device.
2816 * @param[out] fdir_info
2817 * Resulting flow director information.
2820 flow_fdir_info_get(struct rte_eth_dev *dev, struct rte_eth_fdir_info *fdir_info)
2822 struct rte_eth_fdir_masks *mask =
2823 &dev->data->dev_conf.fdir_conf.mask;
2825 fdir_info->mode = dev->data->dev_conf.fdir_conf.mode;
2826 fdir_info->guarant_spc = 0;
2827 rte_memcpy(&fdir_info->mask, mask, sizeof(fdir_info->mask));
2828 fdir_info->max_flexpayload = 0;
2829 fdir_info->flow_types_mask[0] = 0;
2830 fdir_info->flex_payload_unit = 0;
2831 fdir_info->max_flex_payload_segment_num = 0;
2832 fdir_info->flex_payload_limit = 0;
2833 memset(&fdir_info->flex_conf, 0, sizeof(fdir_info->flex_conf));
2837 * Deal with flow director operations.
2840 * Pointer to Ethernet device.
2842 * Operation to perform.
2844 * Pointer to operation-specific structure.
2847 * 0 on success, a negative errno value otherwise and rte_errno is set.
2850 flow_fdir_ctrl_func(struct rte_eth_dev *dev, enum rte_filter_op filter_op,
2853 enum rte_fdir_mode fdir_mode =
2854 dev->data->dev_conf.fdir_conf.mode;
2856 if (filter_op == RTE_ETH_FILTER_NOP)
2858 if (fdir_mode != RTE_FDIR_MODE_PERFECT &&
2859 fdir_mode != RTE_FDIR_MODE_PERFECT_MAC_VLAN) {
2860 DRV_LOG(ERR, "port %u flow director mode %d not supported",
2861 dev->data->port_id, fdir_mode);
2865 switch (filter_op) {
2866 case RTE_ETH_FILTER_ADD:
2867 return flow_fdir_filter_add(dev, arg);
2868 case RTE_ETH_FILTER_UPDATE:
2869 return flow_fdir_filter_update(dev, arg);
2870 case RTE_ETH_FILTER_DELETE:
2871 return flow_fdir_filter_delete(dev, arg);
2872 case RTE_ETH_FILTER_FLUSH:
2873 flow_fdir_filter_flush(dev);
2875 case RTE_ETH_FILTER_INFO:
2876 flow_fdir_info_get(dev, arg);
2879 DRV_LOG(DEBUG, "port %u unknown operation %u",
2880 dev->data->port_id, filter_op);
2888 * Manage filter operations.
2891 * Pointer to Ethernet device structure.
2892 * @param filter_type
2895 * Operation to perform.
2897 * Pointer to operation-specific structure.
2900 * 0 on success, a negative errno value otherwise and rte_errno is set.
2903 mlx5_dev_filter_ctrl(struct rte_eth_dev *dev,
2904 enum rte_filter_type filter_type,
2905 enum rte_filter_op filter_op,
2908 switch (filter_type) {
2909 case RTE_ETH_FILTER_GENERIC:
2910 if (filter_op != RTE_ETH_FILTER_GET) {
2914 *(const void **)arg = &mlx5_flow_ops;
2916 case RTE_ETH_FILTER_FDIR:
2917 return flow_fdir_ctrl_func(dev, filter_op, arg);
2919 DRV_LOG(ERR, "port %u filter type (%d) not supported",
2920 dev->data->port_id, filter_type);
2921 rte_errno = ENOTSUP;