3 # usage: /bin/bash run_test.sh [-46]
4 # Run all defined linux_test[4,6].sh test-cases one by one
5 # user has to setup properly the following environment variables:
6 # SGW_PATH - path to the ipsec-secgw binary to test
7 # REMOTE_HOST - ip/hostname of the DUT
8 # REMOTE_IFACE - iface name for the test-port on DUT
9 # ETH_DEV - ethernet device to be used on SUT by DPDK ('-w <pci-id>')
10 # Also user can optonally setup:
11 # SGW_LCORE - lcore to run ipsec-secgw on (default value is 0)
12 # CRYPTO_DEV - crypto device to be used ('-w <pci-id>')
13 # if none specified appropriate vdevs will be created by the scrit
14 # MULTI_SEG_TEST - ipsec-secgw option to enable reassembly support and
15 # specify size of reassembly table (i.e. MULTI_SEG_TEST="--reassemble 128")
16 # refer to linux_test[4,6].sh for more information
19 # All supported modes to test.
21 # 'old' means that ipsec-secgw will run in legacy (non-librte_ipsec mode)
22 # 'tun/trs' refer to tunnel/transport mode respectively
28 echo -e "\t\t-4 Perform Linux IPv4 network tests"
29 echo -e "\t\t-6 Perform Linux IPv6 network tests"
30 echo -e "\t\t-p Perform packet validation tests"
31 echo -e "\t\t-h Display this help"
34 LINUX_TEST="tun_aescbc_sha1 \
36 tun_aescbc_sha1_esn_atom \
42 trs_aescbc_sha1_esn_atom \
53 tun_aesctr_sha1_esn_atom \
57 trs_aesctr_sha1_esn_atom \
59 tun_3descbc_sha1_old \
60 tun_3descbc_sha1_esn \
61 tun_3descbc_sha1_esn_atom \
63 trs_3descbc_sha1_old \
64 trs_3descbc_sha1_esn \
65 trs_3descbc_sha1_esn_atom"
67 PKT_TESTS="trs_ipv6opts \
68 tun_null_header_reconstruct"
76 while getopts ":46ph" opt
100 # no test suite has been selected
101 if [[ ${run4} -eq 0 && ${run6} -eq 0 && ${runpkt} -eq 0 ]]; then
106 # perform packet processing validation tests
108 if [ $runpkt -eq 1 ]; then
109 echo "Performing packet validation tests"
110 /bin/bash ${DIR}/pkttest.sh ${PKT_TESTS}
113 echo "pkttests finished with status ${st}"
114 if [[ ${st} -ne 0 ]]; then
115 echo "ERROR pkttests FAILED"
120 # perform network tests
121 if [[ ${run4} -eq 1 || ${run6} -eq 1 ]]; then
122 for i in ${LINUX_TEST}; do
124 echo "starting test ${i}"
127 if [[ ${run4} -ne 0 ]]; then
128 /bin/bash ${DIR}/linux_test4.sh ${i}
130 echo "test4 ${i} finished with status ${st4}"
134 if [[ ${run6} -ne 0 ]]; then
135 /bin/bash ${DIR}/linux_test6.sh ${i}
137 echo "test6 ${i} finished with status ${st6}"
141 if [[ $st -ne 0 ]]; then
142 echo "ERROR test ${i} FAILED"