4 * Copyright(c) 2016-2017 Intel Corporation. All rights reserved.
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
10 * * Redistributions of source code must retain the above copyright
11 * notice, this list of conditions and the following disclaimer.
12 * * Redistributions in binary form must reproduce the above copyright
13 * notice, this list of conditions and the following disclaimer in
14 * the documentation and/or other materials provided with the
16 * * Neither the name of Intel Corporation nor the names of its
17 * contributors may be used to endorse or promote products derived
18 * from this software without specific prior written permission.
20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
33 #ifndef _RTE_CRYPTO_SYM_H_
34 #define _RTE_CRYPTO_SYM_H_
37 * @file rte_crypto_sym.h
39 * RTE Definitions for Symmetric Cryptography
41 * Defines symmetric cipher and authentication algorithms and modes, as well
42 * as supported symmetric crypto operation combinations.
52 #include <rte_memory.h>
53 #include <rte_mempool.h>
54 #include <rte_common.h>
57 /** Symmetric Cipher Algorithms */
58 enum rte_crypto_cipher_algorithm {
59 RTE_CRYPTO_CIPHER_NULL = 1,
60 /**< NULL cipher algorithm. No mode applies to the NULL algorithm. */
62 RTE_CRYPTO_CIPHER_3DES_CBC,
63 /**< Triple DES algorithm in CBC mode */
64 RTE_CRYPTO_CIPHER_3DES_CTR,
65 /**< Triple DES algorithm in CTR mode */
66 RTE_CRYPTO_CIPHER_3DES_ECB,
67 /**< Triple DES algorithm in ECB mode */
69 RTE_CRYPTO_CIPHER_AES_CBC,
70 /**< AES algorithm in CBC mode */
71 RTE_CRYPTO_CIPHER_AES_CCM,
72 /**< AES algorithm in CCM mode. When this cipher algorithm is used the
73 * *RTE_CRYPTO_AUTH_AES_CCM* element of the
74 * *rte_crypto_hash_algorithm* enum MUST be used to set up the related
75 * *rte_crypto_auth_xform* structure in the session context or in
76 * the op_params of the crypto operation structure in the case of a
77 * session-less crypto operation
79 RTE_CRYPTO_CIPHER_AES_CTR,
80 /**< AES algorithm in Counter mode */
81 RTE_CRYPTO_CIPHER_AES_ECB,
82 /**< AES algorithm in ECB mode */
83 RTE_CRYPTO_CIPHER_AES_F8,
84 /**< AES algorithm in F8 mode */
85 RTE_CRYPTO_CIPHER_AES_GCM,
86 /**< AES algorithm in GCM mode. When this cipher algorithm is used the
87 * *RTE_CRYPTO_AUTH_AES_GCM* element of the *rte_crypto_auth_algorithm*
88 * enum MUST be used to set up the related *rte_crypto_auth_setup_data*
89 * structure in the session context or in the op_params of the crypto
90 * operation structure in the case of a session-less crypto operation.
92 RTE_CRYPTO_CIPHER_AES_XTS,
93 /**< AES algorithm in XTS mode */
95 RTE_CRYPTO_CIPHER_ARC4,
96 /**< (A)RC4 cipher algorithm */
98 RTE_CRYPTO_CIPHER_KASUMI_F8,
99 /**< KASUMI algorithm in F8 mode */
101 RTE_CRYPTO_CIPHER_SNOW3G_UEA2,
102 /**< SNOW 3G algorithm in UEA2 mode */
104 RTE_CRYPTO_CIPHER_ZUC_EEA3,
105 /**< ZUC algorithm in EEA3 mode */
107 RTE_CRYPTO_CIPHER_DES_CBC,
108 /**< DES algorithm in CBC mode */
110 RTE_CRYPTO_CIPHER_AES_DOCSISBPI,
111 /**< AES algorithm using modes required by
112 * DOCSIS Baseline Privacy Plus Spec.
113 * Chained mbufs are not supported in this mode, i.e. rte_mbuf.next
114 * for m_src and m_dst in the rte_crypto_sym_op must be NULL.
117 RTE_CRYPTO_CIPHER_DES_DOCSISBPI,
118 /**< DES algorithm using modes required by
119 * DOCSIS Baseline Privacy Plus Spec.
120 * Chained mbufs are not supported in this mode, i.e. rte_mbuf.next
121 * for m_src and m_dst in the rte_crypto_sym_op must be NULL.
124 RTE_CRYPTO_CIPHER_LIST_END
128 /** Cipher algorithm name strings */
130 rte_crypto_cipher_algorithm_strings[];
132 /** Symmetric Cipher Direction */
133 enum rte_crypto_cipher_operation {
134 RTE_CRYPTO_CIPHER_OP_ENCRYPT,
135 /**< Encrypt cipher operation */
136 RTE_CRYPTO_CIPHER_OP_DECRYPT
137 /**< Decrypt cipher operation */
140 /** Cipher operation name strings */
142 rte_crypto_cipher_operation_strings[];
145 * Symmetric Cipher Setup Data.
147 * This structure contains data relating to Cipher (Encryption and Decryption)
148 * use to create a session.
150 struct rte_crypto_cipher_xform {
151 enum rte_crypto_cipher_operation op;
152 /**< This parameter determines if the cipher operation is an encrypt or
153 * a decrypt operation. For the RC4 algorithm and the F8/CTR modes,
154 * only encrypt operations are valid.
156 enum rte_crypto_cipher_algorithm algo;
157 /**< Cipher algorithm */
160 uint8_t *data; /**< pointer to key data */
161 size_t length; /**< key length in bytes */
165 * For the RTE_CRYPTO_CIPHER_AES_F8 mode of operation, key.data will
166 * point to a concatenation of the AES encryption key followed by a
167 * keymask. As per RFC3711, the keymask should be padded with trailing
168 * bytes to match the length of the encryption key used.
170 * For AES-XTS mode of operation, two keys must be provided and
171 * key.data must point to the two keys concatenated together (Key1 ||
172 * Key2). The cipher key length will contain the total size of both
175 * Cipher key length is in bytes. For AES it can be 128 bits (16 bytes),
176 * 192 bits (24 bytes) or 256 bits (32 bytes).
178 * For the CCM mode of operation, the only supported key length is 128
181 * For the RTE_CRYPTO_CIPHER_AES_F8 mode of operation, key.length
182 * should be set to the combined length of the encryption key and the
183 * keymask. Since the keymask and the encryption key are the same size,
184 * key.length should be set to 2 x the AES encryption key length.
186 * For the AES-XTS mode of operation:
187 * - Two keys must be provided and key.length refers to total length of
189 * - Each key can be either 128 bits (16 bytes) or 256 bits (32 bytes).
190 * - Both keys must have the same size.
194 /**< Starting point for Initialisation Vector or Counter,
195 * specified as number of bytes from start of crypto
196 * operation (rte_crypto_op).
198 * - For block ciphers in CBC or F8 mode, or for KASUMI
199 * in F8 mode, or for SNOW 3G in UEA2 mode, this is the
200 * Initialisation Vector (IV) value.
202 * - For block ciphers in CTR mode, this is the counter.
204 * - For GCM mode, this is either the IV (if the length
205 * is 96 bits) or J0 (for other sizes), where J0 is as
206 * defined by NIST SP800-38D. Regardless of the IV
207 * length, a full 16 bytes needs to be allocated.
209 * - For CCM mode, the first byte is reserved, and the
210 * nonce should be written starting at &iv[1] (to allow
211 * space for the implementation to write in the flags
212 * in the first byte). Note that a full 16 bytes should
213 * be allocated, even though the length field will
214 * have a value less than this.
216 * - For AES-XTS, this is the 128bit tweak, i, from
217 * IEEE Std 1619-2007.
219 * For optimum performance, the data pointed to SHOULD
223 /**< Length of valid IV data.
225 * - For block ciphers in CBC or F8 mode, or for KASUMI
226 * in F8 mode, or for SNOW 3G in UEA2 mode, this is the
227 * length of the IV (which must be the same as the
228 * block length of the cipher).
230 * - For block ciphers in CTR mode, this is the length
231 * of the counter (which must be the same as the block
232 * length of the cipher).
234 * - For GCM mode, this is either 12 (for 96-bit IVs)
235 * or 16, in which case data points to J0.
237 * - For CCM mode, this is the length of the nonce,
238 * which can be in the range 7 to 13 inclusive.
240 } iv; /**< Initialisation vector parameters */
243 /** Symmetric Authentication / Hash Algorithms */
244 enum rte_crypto_auth_algorithm {
245 RTE_CRYPTO_AUTH_NULL = 1,
246 /**< NULL hash algorithm. */
248 RTE_CRYPTO_AUTH_AES_CBC_MAC,
249 /**< AES-CBC-MAC algorithm. Only 128-bit keys are supported. */
250 RTE_CRYPTO_AUTH_AES_CCM,
251 /**< AES algorithm in CCM mode. This is an authenticated cipher. When
252 * this hash algorithm is used, the *RTE_CRYPTO_CIPHER_AES_CCM*
253 * element of the *rte_crypto_cipher_algorithm* enum MUST be used to
254 * set up the related rte_crypto_cipher_setup_data structure in the
255 * session context or the corresponding parameter in the crypto
256 * operation data structures op_params parameter MUST be set for a
257 * session-less crypto operation.
259 RTE_CRYPTO_AUTH_AES_CMAC,
260 /**< AES CMAC algorithm. */
261 RTE_CRYPTO_AUTH_AES_GCM,
262 /**< AES algorithm in GCM mode. When this hash algorithm
263 * is used, the RTE_CRYPTO_CIPHER_AES_GCM element of the
264 * rte_crypto_cipher_algorithm enum MUST be used to set up the related
265 * rte_crypto_cipher_setup_data structure in the session context, or
266 * the corresponding parameter in the crypto operation data structures
267 * op_params parameter MUST be set for a session-less crypto operation.
269 RTE_CRYPTO_AUTH_AES_GMAC,
270 /**< AES GMAC algorithm. */
271 RTE_CRYPTO_AUTH_AES_XCBC_MAC,
272 /**< AES XCBC algorithm. */
274 RTE_CRYPTO_AUTH_KASUMI_F9,
275 /**< KASUMI algorithm in F9 mode. */
278 /**< MD5 algorithm */
279 RTE_CRYPTO_AUTH_MD5_HMAC,
280 /**< HMAC using MD5 algorithm */
282 RTE_CRYPTO_AUTH_SHA1,
283 /**< 128 bit SHA algorithm. */
284 RTE_CRYPTO_AUTH_SHA1_HMAC,
285 /**< HMAC using 128 bit SHA algorithm. */
286 RTE_CRYPTO_AUTH_SHA224,
287 /**< 224 bit SHA algorithm. */
288 RTE_CRYPTO_AUTH_SHA224_HMAC,
289 /**< HMAC using 224 bit SHA algorithm. */
290 RTE_CRYPTO_AUTH_SHA256,
291 /**< 256 bit SHA algorithm. */
292 RTE_CRYPTO_AUTH_SHA256_HMAC,
293 /**< HMAC using 256 bit SHA algorithm. */
294 RTE_CRYPTO_AUTH_SHA384,
295 /**< 384 bit SHA algorithm. */
296 RTE_CRYPTO_AUTH_SHA384_HMAC,
297 /**< HMAC using 384 bit SHA algorithm. */
298 RTE_CRYPTO_AUTH_SHA512,
299 /**< 512 bit SHA algorithm. */
300 RTE_CRYPTO_AUTH_SHA512_HMAC,
301 /**< HMAC using 512 bit SHA algorithm. */
303 RTE_CRYPTO_AUTH_SNOW3G_UIA2,
304 /**< SNOW 3G algorithm in UIA2 mode. */
306 RTE_CRYPTO_AUTH_ZUC_EIA3,
307 /**< ZUC algorithm in EIA3 mode */
309 RTE_CRYPTO_AUTH_LIST_END
312 /** Authentication algorithm name strings */
314 rte_crypto_auth_algorithm_strings[];
316 /** Symmetric Authentication / Hash Operations */
317 enum rte_crypto_auth_operation {
318 RTE_CRYPTO_AUTH_OP_VERIFY, /**< Verify authentication digest */
319 RTE_CRYPTO_AUTH_OP_GENERATE /**< Generate authentication digest */
322 /** Authentication operation name strings */
324 rte_crypto_auth_operation_strings[];
327 * Authentication / Hash transform data.
329 * This structure contains data relating to an authentication/hash crypto
330 * transforms. The fields op, algo and digest_length are common to all
331 * authentication transforms and MUST be set.
333 struct rte_crypto_auth_xform {
334 enum rte_crypto_auth_operation op;
335 /**< Authentication operation type */
336 enum rte_crypto_auth_algorithm algo;
337 /**< Authentication algorithm selection */
340 uint8_t *data; /**< pointer to key data */
341 size_t length; /**< key length in bytes */
343 /**< Authentication key data.
344 * The authentication key length MUST be less than or equal to the
345 * block size of the algorithm. It is the callers responsibility to
346 * ensure that the key length is compliant with the standard being used
347 * (for example RFC 2104, FIPS 198a).
350 uint16_t digest_length;
351 /**< Length of the digest to be returned. If the verify option is set,
352 * this specifies the length of the digest to be compared for the
355 * It is the caller's responsibility to ensure that the
356 * digest length is compliant with the hash algorithm being used.
357 * If the value is less than the maximum length allowed by the hash,
358 * the result shall be truncated.
361 uint16_t add_auth_data_length;
362 /**< The length of the additional authenticated data (AAD) in bytes.
363 * The maximum permitted value is 65535 (2^16 - 1) bytes, unless
364 * otherwise specified below.
366 * This field must be specified when the hash algorithm is one of the
369 * - For GCM (@ref RTE_CRYPTO_AUTH_AES_GCM). In this case, this is
370 * the length of the Additional Authenticated Data (called A, in NIST
373 * - For CCM (@ref RTE_CRYPTO_AUTH_AES_CCM). In this case, this is
374 * the length of the associated data (called A, in NIST SP800-38C).
375 * Note that this does NOT include the length of any padding, or the
376 * 18 bytes reserved at the start of the above field to store the
377 * block B0 and the encoded length. The maximum permitted value in
378 * this case is 222 bytes.
384 /**< Starting point for Initialisation Vector or Counter,
385 * specified as number of bytes from start of crypto
386 * operation (rte_crypto_op).
388 * - For KASUMI in F9 mode, SNOW 3G in UIA2 mode,
389 * for ZUC in EIA3 mode and for AES-GMAC, this is the
390 * authentication Initialisation Vector (IV) value.
393 * For optimum performance, the data pointed to SHOULD
397 /**< Length of valid IV data.
399 * - For KASUMI in F9 mode, SNOW3G in UIA2 mode, for
400 * ZUC in EIA3 mode and for AES-GMAC, this is the length
404 } iv; /**< Initialisation vector parameters */
408 /** Symmetric AEAD Algorithms */
409 enum rte_crypto_aead_algorithm {
410 RTE_CRYPTO_AEAD_AES_CCM = 1,
411 /**< AES algorithm in CCM mode. */
412 RTE_CRYPTO_AEAD_AES_GCM,
413 /**< AES algorithm in GCM mode. */
414 RTE_CRYPTO_AEAD_LIST_END
417 /** AEAD algorithm name strings */
419 rte_crypto_aead_algorithm_strings[];
421 /** Symmetric AEAD Operations */
422 enum rte_crypto_aead_operation {
423 RTE_CRYPTO_AEAD_OP_ENCRYPT,
424 /**< Encrypt and generate digest */
425 RTE_CRYPTO_AEAD_OP_DECRYPT
426 /**< Verify digest and decrypt */
429 /** Authentication operation name strings */
431 rte_crypto_aead_operation_strings[];
433 struct rte_crypto_aead_xform {
434 enum rte_crypto_aead_operation op;
435 /**< AEAD operation type */
436 enum rte_crypto_aead_algorithm algo;
437 /**< AEAD algorithm selection */
440 uint8_t *data; /**< pointer to key data */
441 size_t length; /**< key length in bytes */
446 /**< Starting point for Initialisation Vector or Counter,
447 * specified as number of bytes from start of crypto
448 * operation (rte_crypto_op).
450 * - For GCM mode, this is either the IV (if the length
451 * is 96 bits) or J0 (for other sizes), where J0 is as
452 * defined by NIST SP800-38D. Regardless of the IV
453 * length, a full 16 bytes needs to be allocated.
455 * - For CCM mode, the first byte is reserved, and the
456 * nonce should be written starting at &iv[1] (to allow
457 * space for the implementation to write in the flags
458 * in the first byte). Note that a full 16 bytes should
459 * be allocated, even though the length field will
460 * have a value less than this.
462 * For optimum performance, the data pointed to SHOULD
466 /**< Length of valid IV data.
468 * - For GCM mode, this is either 12 (for 96-bit IVs)
469 * or 16, in which case data points to J0.
471 * - For CCM mode, this is the length of the nonce,
472 * which can be in the range 7 to 13 inclusive.
474 } iv; /**< Initialisation vector parameters */
476 uint32_t digest_length;
478 uint16_t add_auth_data_length;
479 /**< The length of the additional authenticated data (AAD) in bytes. */
482 /** Crypto transformation types */
483 enum rte_crypto_sym_xform_type {
484 RTE_CRYPTO_SYM_XFORM_NOT_SPECIFIED = 0, /**< No xform specified */
485 RTE_CRYPTO_SYM_XFORM_AUTH, /**< Authentication xform */
486 RTE_CRYPTO_SYM_XFORM_CIPHER, /**< Cipher xform */
487 RTE_CRYPTO_SYM_XFORM_AEAD /**< AEAD xform */
491 * Symmetric crypto transform structure.
493 * This is used to specify the crypto transforms required, multiple transforms
494 * can be chained together to specify a chain transforms such as authentication
495 * then cipher, or cipher then authentication. Each transform structure can
496 * hold a single transform, the type field is used to specify which transform
497 * is contained within the union
499 struct rte_crypto_sym_xform {
500 struct rte_crypto_sym_xform *next;
501 /**< next xform in chain */
502 enum rte_crypto_sym_xform_type type
506 struct rte_crypto_auth_xform auth;
507 /**< Authentication / hash xform */
508 struct rte_crypto_cipher_xform cipher;
510 struct rte_crypto_aead_xform aead;
515 struct rte_cryptodev_sym_session;
518 * Symmetric Cryptographic Operation.
520 * This structure contains data relating to performing symmetric cryptographic
521 * processing on a referenced mbuf data buffer.
523 * When a symmetric crypto operation is enqueued with the device for processing
524 * it must have a valid *rte_mbuf* structure attached, via m_src parameter,
525 * which contains the source data which the crypto operation is to be performed
527 * While the mbuf is in use by a crypto operation no part of the mbuf should be
528 * changed by the application as the device may read or write to any part of the
529 * mbuf. In the case of hardware crypto devices some or all of the mbuf
530 * may be DMAed in and out of the device, so writing over the original data,
531 * though only the part specified by the rte_crypto_sym_op for transformation
533 * Out-of-place (OOP) operation, where the source mbuf is different to the
534 * destination mbuf, is a special case. Data will be copied from m_src to m_dst.
535 * The part copied includes all the parts of the source mbuf that will be
536 * operated on, based on the cipher.data.offset+cipher.data.length and
537 * auth.data.offset+auth.data.length values in the rte_crypto_sym_op. The part
538 * indicated by the cipher parameters will be transformed, any extra data around
539 * this indicated by the auth parameters will be copied unchanged from source to
541 * Also in OOP operation the cipher.data.offset and auth.data.offset apply to
542 * both source and destination mbufs. As these offsets are relative to the
543 * data_off parameter in each mbuf this can result in the data written to the
544 * destination buffer being at a different alignment, relative to buffer start,
545 * to the data in the source buffer.
547 struct rte_crypto_sym_op {
548 struct rte_mbuf *m_src; /**< source mbuf */
549 struct rte_mbuf *m_dst; /**< destination mbuf */
553 struct rte_cryptodev_sym_session *session;
554 /**< Handle for the initialised session context */
555 struct rte_crypto_sym_xform *xform;
556 /**< Session-less API crypto operation parameters */
562 /**< Starting point for cipher processing, specified
563 * as number of bytes from start of data in the source
564 * buffer. The result of the cipher operation will be
565 * written back into the output buffer starting at
569 * For SNOW 3G @ RTE_CRYPTO_CIPHER_SNOW3G_UEA2,
570 * KASUMI @ RTE_CRYPTO_CIPHER_KASUMI_F8
571 * and ZUC @ RTE_CRYPTO_CIPHER_ZUC_EEA3,
572 * this field should be in bits.
576 /**< The message length, in bytes, of the source buffer
577 * on which the cryptographic operation will be
578 * computed. This must be a multiple of the block size
579 * if a block cipher is being used. This is also the
580 * same as the result length.
583 * In the case of CCM @ref RTE_CRYPTO_AUTH_AES_CCM,
584 * this value should not include the length of the
585 * padding or the length of the MAC; the driver will
586 * compute the actual number of bytes over which the
587 * encryption will occur, which will include these
591 * For SNOW 3G @ RTE_CRYPTO_AUTH_SNOW3G_UEA2,
592 * KASUMI @ RTE_CRYPTO_CIPHER_KASUMI_F8
593 * and ZUC @ RTE_CRYPTO_CIPHER_ZUC_EEA3,
594 * this field should be in bits.
596 } data; /**< Data offsets and length for ciphering */
603 /**< Starting point for hash processing, specified as
604 * number of bytes from start of packet in source
608 * For CCM and GCM modes of operation, this field is
609 * ignored. The field @ref aad field
610 * should be set instead.
613 * For SNOW 3G @ RTE_CRYPTO_AUTH_SNOW3G_UIA2,
614 * KASUMI @ RTE_CRYPTO_AUTH_KASUMI_F9
615 * and ZUC @ RTE_CRYPTO_AUTH_ZUC_EIA3,
616 * this field should be in bits.
620 /**< The message length, in bytes, of the source
621 * buffer that the hash will be computed on.
624 * For CCM and GCM modes of operation, this field is
625 * ignored. The field @ref aad field should be set
629 * For SNOW 3G @ RTE_CRYPTO_AUTH_SNOW3G_UIA2,
630 * KASUMI @ RTE_CRYPTO_AUTH_KASUMI_F9
631 * and ZUC @ RTE_CRYPTO_AUTH_ZUC_EIA3,
632 * this field should be in bits.
634 } data; /**< Data offsets and length for authentication */
638 /**< This points to the location where the digest result
639 * should be inserted (in the case of digest generation)
640 * or where the purported digest exists (in the case of
641 * digest verification).
643 * At session creation time, the client specified the
644 * digest result length with the digest_length member
645 * of the @ref rte_crypto_auth_xform structure. For
646 * physical crypto devices the caller must allocate at
647 * least digest_length of physically contiguous memory
650 * For digest generation, the digest result will
651 * overwrite any data at this location.
654 * For GCM (@ref RTE_CRYPTO_AUTH_AES_GCM), for
655 * "digest result" read "authentication tag T".
657 phys_addr_t phys_addr;
658 /**< Physical address of digest */
659 } digest; /**< Digest parameters */
663 /**< Pointer to Additional Authenticated Data (AAD)
664 * needed for authenticated cipher mechanisms (CCM and
667 * The length of the data pointed to by this field is
668 * set up for the session in the @ref
669 * rte_crypto_auth_xform structure as part of the @ref
670 * rte_cryptodev_sym_session_create function call.
671 * This length must not exceed 65535 (2^16-1) bytes.
673 * Specifically for CCM (@ref RTE_CRYPTO_AUTH_AES_CCM),
674 * the caller should setup this field as follows:
676 * - the nonce should be written starting at an offset
677 * of one byte into the array, leaving room for the
678 * implementation to write in the flags to the first
681 * - the additional authentication data itself should
682 * be written starting at an offset of 18 bytes into
683 * the array, leaving room for the length encoding in
684 * the first two bytes of the second block.
686 * - the array should be big enough to hold the above
687 * fields, plus any padding to round this up to the
688 * nearest multiple of the block size (16 bytes).
689 * Padding will be added by the implementation.
691 * Finally, for GCM (@ref RTE_CRYPTO_AUTH_AES_GCM), the
692 * caller should setup this field as follows:
694 * - the AAD is written in starting at byte 0
695 * - the array must be big enough to hold the AAD, plus
696 * any space to round this up to the nearest multiple
697 * of the block size (16 bytes).
700 phys_addr_t phys_addr; /**< physical address */
702 /**< Additional authentication parameters */
708 * Reset the fields of a symmetric operation to their default values.
710 * @param op The crypto operation to be reset.
713 __rte_crypto_sym_op_reset(struct rte_crypto_sym_op *op)
715 memset(op, 0, sizeof(*op));
720 * Allocate space for symmetric crypto xforms in the private data space of the
721 * crypto operation. This also defaults the crypto xform type to
722 * RTE_CRYPTO_SYM_XFORM_NOT_SPECIFIED and configures the chaining of the xforms
723 * in the crypto operation
726 * - On success returns pointer to first crypto xform in crypto operations chain
727 * - On failure returns NULL
729 static inline struct rte_crypto_sym_xform *
730 __rte_crypto_sym_op_sym_xforms_alloc(struct rte_crypto_sym_op *sym_op,
731 void *priv_data, uint8_t nb_xforms)
733 struct rte_crypto_sym_xform *xform;
735 sym_op->xform = xform = (struct rte_crypto_sym_xform *)priv_data;
738 xform->type = RTE_CRYPTO_SYM_XFORM_NOT_SPECIFIED;
739 xform = xform->next = --nb_xforms > 0 ? xform + 1 : NULL;
742 return sym_op->xform;
747 * Attach a session to a symmetric crypto operation
749 * @param sym_op crypto operation
750 * @param sess cryptodev session
753 __rte_crypto_sym_op_attach_sym_session(struct rte_crypto_sym_op *sym_op,
754 struct rte_cryptodev_sym_session *sess)
756 sym_op->session = sess;
766 #endif /* _RTE_CRYPTO_SYM_H_ */