.. SPDX-License-Identifier: BSD-3-Clause
- Copyright(c) 2015-2016 Intel Corporation.
+ Copyright(c) 2015-2019 Intel Corporation.
Intel(R) QuickAssist (QAT) Crypto Poll Mode Driver
==================================================
-The QAT PMD provides poll mode crypto driver support for the following
-hardware accelerator devices:
+QAT documentation consists of three parts:
+
+* Details of the symmetric and asymmetric crypto services below.
+* Details of the `compression service <http://doc.dpdk.org/guides/compressdevs/qat_comp.html>`_
+ in the compressdev drivers section.
+* Details of building the common QAT infrastructure and the PMDs to support the
+ above services. See :ref:`building_qat` below.
+
+
+Symmetric Crypto Service on QAT
+-------------------------------
+
+The QAT symmetric crypto PMD (hereafter referred to as `QAT SYM [PMD]`) provides
+poll mode crypto driver support for the following hardware accelerator devices:
* ``Intel QuickAssist Technology DH895xCC``
* ``Intel QuickAssist Technology C62x``
* ``Intel QuickAssist Technology C3xxx``
* ``Intel QuickAssist Technology D15xx``
+* ``Intel QuickAssist Technology C4xxx``
Features
---------
+~~~~~~~~
-The QAT PMD has support for:
+The QAT SYM PMD has support for:
Cipher algorithms:
* ``RTE_CRYPTO_CIPHER_AES128_CTR``
* ``RTE_CRYPTO_CIPHER_AES192_CTR``
* ``RTE_CRYPTO_CIPHER_AES256_CTR``
+* ``RTE_CRYPTO_CIPHER_AES_XTS``
* ``RTE_CRYPTO_CIPHER_SNOW3G_UEA2``
* ``RTE_CRYPTO_CIPHER_NULL``
* ``RTE_CRYPTO_CIPHER_KASUMI_F8``
* ``RTE_CRYPTO_AUTH_KASUMI_F9``
* ``RTE_CRYPTO_AUTH_AES_GMAC``
* ``RTE_CRYPTO_AUTH_ZUC_EIA3``
+* ``RTE_CRYPTO_AUTH_AES_CMAC``
Supported AEAD algorithms:
* ``RTE_CRYPTO_AEAD_AES_GCM``
+* ``RTE_CRYPTO_AEAD_AES_CCM``
Limitations
------------
+~~~~~~~~~~~
* Only supports the session-oriented API implementation (session-less APIs are not supported).
* SNOW 3G (UEA2), KASUMI (F8) and ZUC (EEA3) supported only if cipher length and offset fields are byte-multiple.
* SNOW 3G (UIA2) and ZUC (EIA3) supported only if hash length and offset fields are byte-multiple.
* No BSD support as BSD QAT kernel driver not available.
* ZUC EEA3/EIA3 is not supported by dh895xcc devices
-* Maximum additional authenticated data (AAD) for GCM is 240 bytes long.
+* Maximum additional authenticated data (AAD) for GCM is 240 bytes long and must be passed to the device in a buffer rounded up to the nearest block-size multiple (x16) and padded with zeros.
+* Queue pairs are not thread-safe (that is, within a single queue pair, RX and TX from different lcores is not supported).
+
+Extra notes on KASUMI F9
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+When using KASUMI F9 authentication algorithm, the input buffer must be
+constructed according to the
+`3GPP KASUMI specification <http://cryptome.org/3gpp/35201-900.pdf>`_
+(section 4.4, page 13). The input buffer has to have COUNT (4 bytes),
+FRESH (4 bytes), MESSAGE and DIRECTION (1 bit) concatenated. After the DIRECTION
+bit, a single '1' bit is appended, followed by between 0 and 7 '0' bits, so that
+the total length of the buffer is multiple of 8 bits. Note that the actual
+message can be any length, specified in bits.
+
+Once this buffer is passed this way, when creating the crypto operation,
+length of data to authenticate "op.sym.auth.data.length" must be the length
+of all the items described above, including the padding at the end.
+Also, offset of data to authenticate "op.sym.auth.data.offset"
+must be such that points at the start of the COUNT bytes.
+
+Asymmetric Crypto Service on QAT
+--------------------------------
+
+The QAT asymmetric crypto PMD (hereafter referred to as `QAT ASYM [PMD]`) provides
+poll mode crypto driver support for the following hardware accelerator devices:
+
+* ``Intel QuickAssist Technology DH895xCC``
+* ``Intel QuickAssist Technology C62x``
+* ``Intel QuickAssist Technology C3xxx``
+* ``Intel QuickAssist Technology D15xx``
+* ``Intel QuickAssist Technology C4xxx``
+
+The QAT ASYM PMD has support for:
+
+* ``RTE_CRYPTO_ASYM_XFORM_MODEX``
+* ``RTE_CRYPTO_ASYM_XFORM_MODINV``
+
+Limitations
+~~~~~~~~~~~
+
+* Big integers longer than 4096 bits are not supported.
* Queue pairs are not thread-safe (that is, within a single queue pair, RX and TX from different lcores is not supported).
+.. _building_qat:
+
+Building PMDs on QAT
+--------------------
-Installation
-------------
+A QAT device can host multiple acceleration services:
-To enable QAT in DPDK, follow the instructions for modifying the compile-time
-configuration file as described `here <http://dpdk.org/doc/guides/linux_gsg/build_dpdk.html>`_.
+* symmetric cryptography
+* data compression
+* asymmetric cryptography
-Quick instructions are as follows:
+These services are provided to DPDK applications via PMDs which register to
+implement the corresponding cryptodev and compressdev APIs. The PMDs use
+common QAT driver code which manages the QAT PCI device. They also depend on a
+QAT kernel driver being installed on the platform, see :ref:`qat_kernel` below.
+
+
+Configuring and Building the DPDK QAT PMDs
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+
+Further information on configuring, building and installing DPDK is described
+`here <http://doc.dpdk.org/guides/linux_gsg/build_dpdk.html>`_.
+
+
+Quick instructions for QAT cryptodev PMD are as follows:
.. code-block:: console
cd to the top-level DPDK directory
- make config T=x86_64-native-linuxapp-gcc
- sed -i 's,\(CONFIG_RTE_LIBRTE_PMD_QAT\)=n,\1=y,' build/.config
+ make defconfig
+ sed -i 's,\(CONFIG_RTE_LIBRTE_PMD_QAT_SYM\)=n,\1=y,' build/.config
+ or/and
+ sed -i 's,\(CONFIG_RTE_LIBRTE_PMD_QAT_ASYM\)=n,\1=y,' build/.config
make
-To use the DPDK QAT PMD an SRIOV-enabled QAT kernel driver is required. The VF
-devices exposed by this driver will be used by the QAT PMD. The devices and
-available kernel drivers and device ids are :
+Quick instructions for QAT compressdev PMD are as follows:
+
+.. code-block:: console
+
+ cd to the top-level DPDK directory
+ make defconfig
+ make
+
+
+.. _building_qat_config:
+
+Build Configuration
+~~~~~~~~~~~~~~~~~~~
+
+These are the build configuration options affecting QAT, and their default values:
+
+.. code-block:: console
+
+ CONFIG_RTE_LIBRTE_PMD_QAT=y
+ CONFIG_RTE_LIBRTE_PMD_QAT_SYM=n
+ CONFIG_RTE_LIBRTE_PMD_QAT_ASYM=n
+ CONFIG_RTE_PMD_QAT_MAX_PCI_DEVICES=48
+ CONFIG_RTE_PMD_QAT_COMP_IM_BUFFER_SIZE=65536
+
+CONFIG_RTE_LIBRTE_PMD_QAT must be enabled for any QAT PMD to be built.
+
+Both QAT SYM PMD and QAT ASYM PMD have an external dependency on libcrypto, so are not
+built by default. CONFIG_RTE_LIBRTE_PMD_QAT_SYM/ASYM should be enabled to build them.
+
+The QAT compressdev PMD has no external dependencies, so needs no configuration
+options and is built by default.
+
+The number of VFs per PF varies - see table below. If multiple QAT packages are
+installed on a platform then CONFIG_RTE_PMD_QAT_MAX_PCI_DEVICES should be
+adjusted to the number of VFs which the QAT common code will need to handle.
+
+.. Note::
+
+ There are separate config items (not QAT-specific) for max cryptodevs
+ CONFIG_RTE_CRYPTO_MAX_DEVS and max compressdevs CONFIG_RTE_COMPRESS_MAX_DEVS,
+ if necessary these should be adjusted to handle the total of QAT and other
+ devices which the process will use. In particular for crypto, where each
+ QAT VF may expose two crypto devices, sym and asym, it may happen that the
+ number of devices will be bigger than MAX_DEVS and the process will show an error
+ during PMD initialisation. To avoid this problem CONFIG_RTE_CRYPTO_MAX_DEVS may be
+ increased or -w, pci-whitelist domain:bus:devid:func option may be used.
+
+
+QAT compression PMD needs intermediate buffers to support Deflate compression
+with Dynamic Huffman encoding. CONFIG_RTE_PMD_QAT_COMP_IM_BUFFER_SIZE
+specifies the size of a single buffer, the PMD will allocate a multiple of these,
+plus some extra space for associated meta-data. For GEN2 devices, 20 buffers are
+allocated while for GEN1 devices, 12 buffers are allocated, plus 1472 bytes overhead.
+
+.. Note::
+
+ If the compressed output of a Deflate operation using Dynamic Huffman
+ Encoding is too big to fit in an intermediate buffer, then the
+ operation will fall back to fixed compression rather than failing the operation.
+ To avoid this less performant case, applications should configure
+ the intermediate buffer size to be larger than the expected input data size
+ (compressed output size is usually unknown, so the only option is to make
+ larger than the input size).
+
+
+Device and driver naming
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+* The qat cryptodev symmetric crypto driver name is "crypto_qat".
+* The qat cryptodev asymmetric crypto driver name is "crypto_qat_asym".
+
+The "rte_cryptodev_devices_get()" returns the devices exposed by either of these drivers.
+
+* Each qat sym crypto device has a unique name, in format
+ "<pci bdf>_<service>", e.g. "0000:41:01.0_qat_sym".
+* Each qat asym crypto device has a unique name, in format
+ "<pci bdf>_<service>", e.g. "0000:41:01.0_qat_asym".
+ This name can be passed to "rte_cryptodev_get_dev_id()" to get the device_id.
+
+.. Note::
+
+ The cryptodev driver name is passed to the dpdk-test-crypto-perf tool in the "-devtype" parameter.
+
+ The qat crypto device name is in the format of the slave parameter passed to the crypto scheduler.
+
+* The qat compressdev driver name is "compress_qat".
+ The rte_compressdev_devices_get() returns the devices exposed by this driver.
+
+* Each qat compression device has a unique name, in format
+ <pci bdf>_<service>, e.g. "0000:41:01.0_qat_comp".
+ This name can be passed to rte_compressdev_get_dev_id() to get the device_id.
+
+.. _qat_kernel:
+
+Dependency on the QAT kernel driver
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+To use QAT an SRIOV-enabled QAT kernel driver is required. The VF
+devices created and initialised by this driver will be used by the QAT PMDs.
+
+Instructions for installation are below, but first an explanation of the
+relationships between the PF/VF devices and the PMDs visible to
+DPDK applications.
+
+Each QuickAssist PF device exposes a number of VF devices. Each VF device can
+enable one symmetric cryptodev PMD and/or one asymmetric cryptodev PMD and/or
+one compressdev PMD.
+These QAT PMDs share the same underlying device and pci-mgmt code, but are
+enumerated independently on their respective APIs and appear as independent
+devices to applications.
+
+.. Note::
+
+ Each VF can only be used by one DPDK process. It is not possible to share
+ the same VF across multiple processes, even if these processes are using
+ different acceleration services.
+
+ Conversely one DPDK process can use one or more QAT VFs and can expose both
+ cryptodev and compressdev instances on each of those VFs.
+
+
+Available kernel drivers
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Kernel drivers for each device for each service are listed in the following table. (Scroll right
+to see the full table)
+
.. _table_qat_pmds_drivers:
.. table:: QAT device generations, devices and drivers
- +-----+----------+--------+---------------+------------+--------+------+--------+--------+
- | Gen | Device | Driver | Kernel Module | Pci Driver | PF Did | #PFs | Vf Did | VFs/PF |
- +=====+==========+========+===============+============+========+======+========+========+
- | 1 | DH895xCC | 01.org | icp_qa_al | n/a | 435 | 1 | 443 | 32 |
- +-----+----------+--------+---------------+------------+--------+------+--------+--------+
- | 1 | DH895xCC | 4.4+ | qat_dh895xcc | dh895xcc | 435 | 1 | 443 | 32 |
- +-----+----------+--------+---------------+------------+--------+------+--------+--------+
- | 2 | C62x | 4.5+ | qat_c62x | c6xx | 37c8 | 3 | 37c9 | 16 |
- +-----+----------+--------+---------------+------------+--------+------+--------+--------+
- | 2 | C3xxx | 4.5+ | qat_c3xxx | c3xxx | 19e2 | 1 | 19e3 | 16 |
- +-----+----------+--------+---------------+------------+--------+------+--------+--------+
- | 2 | D15xx | p | qat_d15xx | d15xx | 6f54 | 1 | 6f55 | 16 |
- +-----+----------+--------+---------------+------------+--------+------+--------+--------+
-
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | S | A | C | Gen | Device | Driver/ver | Kernel Module | Pci Driver | PF Did | #PFs | VF Did | VFs/PF |
+ +=====+=====+=====+=====+==========+===============+===============+============+========+======+========+========+
+ | Yes | No | No | 1 | DH895xCC | linux/4.4+ | qat_dh895xcc | dh895xcc | 435 | 1 | 443 | 32 |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | Yes | No | " | " | 01.org/4.2.0+ | " | " | " | " | " | " |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | Yes | Yes | " | " | 01.org/4.3.0+ | " | " | " | " | " | " |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | No | No | 2 | C62x | linux/4.5+ | qat_c62x | c6xx | 37c8 | 3 | 37c9 | 16 |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | Yes | Yes | " | " | 01.org/4.2.0+ | " | " | " | " | " | " |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | No | No | 2 | C3xxx | linux/4.5+ | qat_c3xxx | c3xxx | 19e2 | 1 | 19e3 | 16 |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | Yes | Yes | " | " | 01.org/4.2.0+ | " | " | " | " | " | " |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | No | No | 2 | D15xx | p | qat_d15xx | d15xx | 6f54 | 1 | 6f55 | 16 |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+ | Yes | No | No | 3 | C4xxx | p | qat_c4xxx | c4xxx | 18a0 | 1 | 18a1 | 128 |
+ +-----+-----+-----+-----+----------+---------------+---------------+------------+--------+------+--------+--------+
+
+The first 3 columns indicate the service:
+
+* S = Symmetric crypto service (via cryptodev API)
+* A = Asymmetric crypto service (via cryptodev API)
+* C = Compression service (via compressdev API)
The ``Driver`` column indicates either the Linux kernel version in which
support for this device was introduced or a driver available on Intel's 01.org
-website. There are both linux and 01.org kernel drivers available for some
+website. There are both linux in-tree and 01.org kernel drivers available for some
devices. p = release pending.
If you are running on a kernel which includes a driver for your device, see
Installation using kernel.org driver
-------------------------------------
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The examples below are based on the C62x device, if you have a different device
use the corresponding values in the above table.
Installation using 01.org QAT driver
-------------------------------------
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Download the latest QuickAssist Technology Driver from `01.org
<https://01.org/packet-processing/intel%C2%AE-quickassist-technology-drivers-and-patches>`_.
The steps below assume you are:
-* Building on a platform with one ``DH895xCC`` device.
-* Using package ``qatmux.l.2.3.0-34.tgz``.
-* On Fedora21 kernel ``3.17.4-301.fc21.x86_64``.
+* Building on a platform with one ``C62x`` device.
+* Using package ``qat1.7.l.4.2.0-000xx.tar.gz``.
+* On Fedora26 kernel ``4.11.11-300.fc26.x86_64``.
In the BIOS ensure that SRIOV is enabled and VT-d is disabled.
* ``./installer.sh uninstall`` in the directory where originally installed.
-* or ``rmmod qat_dh895xcc; rmmod intel_qat``.
Build and install the SRIOV-enabled QAT driver::
mkdir /QAT
cd /QAT
- # Copy qatmux.l.2.3.0-34.tgz to this location
- tar zxof qatmux.l.2.3.0-34.tgz
+ # Copy the package to this location and unpack
+ tar zxof qat1.7.l.4.2.0-000xx.tar.gz
+
+ ./configure --enable-icp-sriov=host
+ make install
+
+You can use ``cat /sys/kernel/debug/qat<your device type and bdf>/version/fw`` to confirm the driver is correctly installed and is using firmware version 4.2.0.
+You can use ``lspci -d:37c9`` to confirm the presence of the 16 VF devices available per ``C62x`` PF.
+
+Confirm the driver is correctly installed and is using firmware version 4.2.0::
- export ICP_WITHOUT_IOMMU=1
- ./installer.sh install QAT1.6 host
+ cat /sys/kernel/debug/qat<your device type and bdf>/version/fw
+
+
+Confirm the presence of 48 VF devices - 16 per PF::
+
+ lspci -d:37c9
-You can use ``cat /proc/icp_dh895xcc_dev0/version`` to confirm the driver is correctly installed.
-You can use ``lspci -d:443`` to confirm the of the 32 VF devices available per ``DH895xCC`` device.
To complete the installation - follow instructions in `Binding the available VFs to the DPDK UIO driver`_.
sudo yum install zlib-devel
sudo yum install openssl-devel
+ sudo yum install libudev-devel
.. Note::
Binding the available VFs to the DPDK UIO driver
-------------------------------------------------
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Unbind the VFs from the stock driver so they can be bound to the uio driver.
For an Intel(R) QuickAssist Technology DH895xCC device
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The unbind command below assumes ``BDFs`` of ``03:01.00-03:04.07``, if your
VFs are different adjust the unbind command below::
done
For an Intel(R) QuickAssist Technology C62x device
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The unbind command below assumes ``BDFs`` of ``1a:01.00-1a:02.07``,
``3d:01.00-3d:02.07`` and ``3f:01.00-3f:02.07``, if your VFs are different
done
For Intel(R) QuickAssist Technology C3xxx or D15xx device
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The unbind command below assumes ``BDFs`` of ``01:01.00-01:02.07``, if your
VFs are different adjust the unbind command below::
done
Bind to the DPDK uio driver
-~~~~~~~~~~~~~~~~~~~~~~~~~~~
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
Install the DPDK igb_uio driver, bind the VF PCI Device id to it and use lspci
to confirm the VF devices are now in use by igb_uio kernel driver,
cd to the top-level DPDK directory
./usertools/dpdk-devbind.py -b igb_uio 0000:03:01.1
+Testing
+~~~~~~~
-Extra notes on KASUMI F9
-------------------------
+QAT SYM crypto PMD can be tested by running the test application::
-When using KASUMI F9 authentication algorithm, the input buffer must be
-constructed according to the 3GPP KASUMI specifications (section 4.4, page 13):
-`<http://cryptome.org/3gpp/35201-900.pdf>`_.
-Input buffer has to have COUNT (4 bytes), FRESH (4 bytes), MESSAGE and DIRECTION (1 bit)
-concatenated. After the DIRECTION bit, a single '1' bit is appended, followed by
-between 0 and 7 '0' bits, so that the total length of the buffer is multiple of 8 bits.
-Note that the actual message can be any length, specified in bits.
+ make defconfig
+ make -j
+ cd ./build/app
+ ./test -l1 -n1 -w <your qat bdf>
+ RTE>>cryptodev_qat_autotest
-Once this buffer is passed this way, when creating the crypto operation,
-length of data to authenticate (op.sym.auth.data.length) must be the length
-of all the items described above, including the padding at the end.
-Also, offset of data to authenticate (op.sym.auth.data.offset)
-must be such that points at the start of the COUNT bytes.
+QAT ASYM crypto PMD can be tested by running the test application::
-Device and driver naming
-------------------------
+ make defconfig
+ make -j
+ cd ./build/app
+ ./test -l1 -n1 -w <your qat bdf>
+ RTE>>cryptodev_qat_asym_autotest
+
+QAT compression PMD can be tested by running the test application::
+
+ make defconfig
+ sed -i 's,\(CONFIG_RTE_COMPRESSDEV_TEST\)=n,\1=y,' build/.config
+ make -j
+ cd ./build/app
+ ./test -l1 -n1 -w <your qat bdf>
+ RTE>>compressdev_autotest
+
+
+Debugging
+~~~~~~~~~
+
+There are 2 sets of trace available via the dynamic logging feature:
+
+* pmd.qat_dp exposes trace on the data-path.
+* pmd.qat_general exposes all other trace.
+
+pmd.qat exposes both sets of traces.
+They can be enabled using the log-level option (where 8=maximum log level) on
+the process cmdline, e.g. using any of the following::
+
+ --log-level="pmd.qat_general,8"
+ --log-level="pmd.qat_dp,8"
+ --log-level="pmd.qat,8"
+
+.. Note::
-The qat crypto driver name is "crypto_qat".
-This name is passed to the dpdk-test-crypto-perf tool in the -devtype parameter.
-The rte_cryptodev_devices_get() can return the devices exposed by a driver.
+ The global RTE_LOG_DP_LEVEL overrides data-path trace so must be set to
+ RTE_LOG_DEBUG to see all the trace. This variable is in config/rte_config.h
+ for meson build and config/common_base for gnu make.
+ Also the dynamic global log level overrides both sets of trace, so e.g. no
+ QAT trace would display in this case::
-Each qat crypto device has a unique name, in format
-<pci bdf>_<service>, e.g. "0000:41:01.0_qat_sym".
-This name can be passed to rte_cryptodev_get_dev_id() to get the device_id.
-This is also the format of the slave parameter passed to the crypto scheduler.
+ --log-level="7" --log-level="pmd.qat_general,8"