-
-.. code-block:: console
-
- ls x86_64-native-linuxapp-gcc
-
- app build hostapp include kmod lib Makefile
-
-Loading Modules to Enable Userspace IO for DPDK
------------------------------------------------
-
-To run any DPDK application, a suitable uio module can be loaded into the running kernel.
-In many cases, the standard ``uio_pci_generic`` module included in the Linux kernel
-can provide the uio capability. This module can be loaded using the command
-
-.. code-block:: console
-
- sudo modprobe uio_pci_generic
-
-As an alternative to the ``uio_pci_generic``, the DPDK also includes the igb_uio
-module which can be found in the kmod subdirectory referred to above. It can
-be loaded as shown below:
-
-.. code-block:: console
-
- sudo modprobe uio
- sudo insmod kmod/igb_uio.ko
-
-.. note::
-
- For some devices which lack support for legacy interrupts, e.g. virtual function
- (VF) devices, the ``igb_uio`` module may be needed in place of ``uio_pci_generic``.
-
-Since DPDK release 1.7 onward provides VFIO support, use of UIO is optional
-for platforms that support using VFIO.
-
-Loading VFIO Module
--------------------
-
-To run an DPDK application and make use of VFIO, the ``vfio-pci`` module must be loaded:
-
-.. code-block:: console
-
- sudo modprobe vfio-pci
-
-Note that in order to use VFIO, your kernel must support it.
-VFIO kernel modules have been included in the Linux kernel since version 3.6.0 and are usually present by default,
-however please consult your distributions documentation to make sure that is the case.
-
-Also, to use VFIO, both kernel and BIOS must support and be configured to use IO virtualization (such as Intel® VT-d).
-
-For proper operation of VFIO when running DPDK applications as a non-privileged user, correct permissions should also be set up.
-This can be done by using the DPDK setup script (called setup.sh and located in the tools directory).
-
-.. _linux_gsg_binding_kernel:
-
-Binding and Unbinding Network Ports to/from the Kernel Modules
---------------------------------------------------------------
-
-As of release 1.4, DPDK applications no longer automatically unbind all supported network ports from the kernel driver in use.
-Instead, all ports that are to be used by an DPDK application must be bound to the
-``uio_pci_generic``, ``igb_uio`` or ``vfio-pci`` module before the application is run.
-Any network ports under Linux* control will be ignored by the DPDK poll-mode drivers and cannot be used by the application.
-
-.. warning::
-
- The DPDK will, by default, no longer automatically unbind network ports from the kernel driver at startup.
- Any ports to be used by an DPDK application must be unbound from Linux* control and
- bound to the ``uio_pci_generic``, ``igb_uio`` or ``vfio-pci`` module before the application is run.
-
-To bind ports to the ``uio_pci_generic``, ``igb_uio`` or ``vfio-pci`` module for DPDK use,
-and then subsequently return ports to Linux* control,
-a utility script called dpdk_nic _bind.py is provided in the tools subdirectory.
-This utility can be used to provide a view of the current state of the network ports on the system,
-and to bind and unbind those ports from the different kernel modules, including the uio and vfio modules.
-The following are some examples of how the script can be used.
-A full description of the script and its parameters can be obtained by calling the script with the ``--help`` or ``--usage`` options.
-Note that the uio or vfio kernel modules to be used, should be loaded into the kernel before
-running the ``dpdk_nic_bind.py`` script.
-
-.. warning::
-
- Due to the way VFIO works, there are certain limitations to which devices can be used with VFIO.
- Mainly it comes down to how IOMMU groups work.
- Any Virtual Function device can be used with VFIO on its own, but physical devices will require either all ports bound to VFIO,
- or some of them bound to VFIO while others not being bound to anything at all.
-
- If your device is behind a PCI-to-PCI bridge, the bridge will then be part of the IOMMU group in which your device is in.
- Therefore, the bridge driver should also be unbound from the bridge PCI device for VFIO to work with devices behind the bridge.
-
-.. warning::
-
- While any user can run the dpdk_nic_bind.py script to view the status of the network ports,
- binding or unbinding network ports requires root privileges.
-
-To see the status of all network ports on the system:
-
-.. code-block:: console
-
- ./tools/dpdk_nic_bind.py --status
-
- Network devices using DPDK-compatible driver
- ============================================
- 0000:82:00.0 '82599EB 10-GbE NIC' drv=uio_pci_generic unused=ixgbe
- 0000:82:00.1 '82599EB 10-GbE NIC' drv=uio_pci_generic unused=ixgbe
-
- Network devices using kernel driver
- ===================================
- 0000:04:00.0 'I350 1-GbE NIC' if=em0 drv=igb unused=uio_pci_generic *Active*
- 0000:04:00.1 'I350 1-GbE NIC' if=eth1 drv=igb unused=uio_pci_generic
- 0000:04:00.2 'I350 1-GbE NIC' if=eth2 drv=igb unused=uio_pci_generic
- 0000:04:00.3 'I350 1-GbE NIC' if=eth3 drv=igb unused=uio_pci_generic
-
- Other network devices
- =====================
- <none>
-
-To bind device ``eth1``,``04:00.1``, to the ``uio_pci_generic`` driver:
-
-.. code-block:: console
-
- ./tools/dpdk_nic_bind.py --bind=uio_pci_generic 04:00.1
-
-or, alternatively,
-
-.. code-block:: console
-
- ./tools/dpdk_nic_bind.py --bind=uio_pci_generic eth1
-
-To restore device ``82:00.0`` to its original kernel binding:
-
-.. code-block:: console
-
- ./tools/dpdk_nic_bind.py --bind=ixgbe 82:00.0
git.droids-corp.org / dpdk.git / blobdiff