+* **e1000/base: Synchronize PHY interface on non-ME systems.**
+
+ On power up, the MAC - PHY interface needs to be set to PCIe, even if the
+ cable is disconnected. In ME systems, the ME handles this on exit from the
+ Sx (Sticky mode) state. In non-ME, the driver handles it. Added a check for
+ non-ME system to the driver code that handles it.
+
+* **e1000/base: Increased timeout of reset check.**
+
+ Previously, in ``check_reset_block`` RSPCIPHY was polled for 100 ms before
+ determining that the ME veto was set. This was not enough and it was
+ increased to 300 ms.
+
+* **e1000/base: Disabled IPv6 extension header parsing on 82575.**
+
+ Disabled IPv6 options as per hardware limitation.
+
+* **e1000/base: Prevent ULP flow if cable connected.**
+
+ Enabling ULP on link down when the cable is connected caused an infinite
+ loop of link up/down indications in the NDIS driver.
+ The driver now enables ULP only when the cable is disconnected.
+
+* **e1000/base: Support different EEARBC for i210.**
+
+ EEARBC has changed on i210. It means EEARBC has a different address on
+ i210 than on other NICs. So, add a new entity named EEARBC_I210 to the
+ register list and make sure the right one is being used on i210.
+
+* **e1000/base: Fix K1 configuration.**
+
+ Added fix for the following updates to the K1 configurations:
+ TX idle period for entering K1 should be 128 ns.
+ Minimum TX idle period in K1 should be 256 ns.
+
+* **e1000/base: Fix link detect flow.**
+
+ Fix link detect flow in case where auto-negotiate is not enabled, by calling
+ ``e1000_setup_copper_link_generic`` instead of ``e1000_phy_setup_autoneg``.
+
+* **e1000/base: Fix link check for i354 M88E1112 PHY.**
+
+ The ``e1000_check_for_link_media_swap()`` function is supposed to check PHY
+ page 0 for copper and PHY page 1 for "other" (fiber) links. The driver
+ switched back from page 1 to page 0 too soon, before
+ ``e1000_check_for_link_82575()`` is executed and was never finding the link
+ on the fiber (other).
+
+ If the link is copper, as the M88E1112 page address is set to 1, it should be
+ set back to 0 before checking this link.
+
+* **e1000/base: Fix beacon duration for i217.**
+
+ Fix for I217 Packet Loss issue - The Management Engine sets the FEXTNVM4
+ Beacon Duration incorrectly. This fix ensures that the correct value will
+ always be set. Correct value for this field is 8 usec.
+
+* **e1000/base: Fix TIPG for non 10 half duplex mode.**
+
+ TIPG value is increased when setting speed to 10 half duplex to prevent
+ packet loss. However, it was never decreased again when speed
+ changed. This caused performance issues in the NDIS driver.
+ Fix this to restore TIPG to default value on non 10 half duplex.
+
+* **e1000/base: Fix reset of DH89XXCC SGMII.**
+
+ For DH89XXCC_SGMII, a write flush leaves registers of this device trashed
+ (0xFFFFFFFF). Add check for this device.
+
+ Also, after both Port SW Reset and Device Reset case, the platform should
+ wait at least 3ms before reading any registers. Remove this condition since
+ waiting is conditionally executed only for Device Reset.
+
+* **e1000/base: Fix redundant PHY power down for i210.**
+
+ Bit 11 of PHYREG 0 is used to power down PHY. The use of PHYREG 16 is
+ no longer necessary.
+
+* **e1000/base: fix jumbo frame CRC failures.**
+
+ Change the value of register 776.20[11:2] for jumbo mode from 0x1A to 0x1F.
+ This is to enlarge the gap between read and write pointers in the TX FIFO.
+
+* **e1000/base: Fix link flap on 82579.**
+
+ Several customers have reported a link flap issue on 82579. The symptoms
+ are random and intermittent link losses when 82579 is connected to specific
+ switches. the Issue was root caused as an inter-operability problem between
+ the NIC and at least some Broadcom PHYs in the Energy Efficient Ethernet
+ wake mechanism.
+
+ To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
+ Low Power Idle. This solution will cause an increase of power in 100M EEE
+ link. It may cost an additional 28mW in this specific mode.
+
+* **igb: Fixed IEEE1588 frame identification in I210.**
+
+ Fixed issue where the flag ``PKT_RX_IEEE1588_PTP`` was not being set
+ in the Intel I210 NIC, as the EtherType in RX descriptor is in bits 8:10 of
+ Packet Type and not in the default bits 0:2.
+
+* **igb: Fixed VF start with PF stopped.**
+
+ VF needs the PF interrupt support initialized even if not started.
+
+* **igb: Fixed VF MAC address when using with DPDK PF.**
+
+ Assign a random MAC address in VF when not assigned by PF.
+
+* **igb: Removed CRC bytes from byte counter statistics.**
+