doc: add tested Marvell integrated NIC platforms

[dpdk.git] / doc / guides / sample_app_ug / l2_forward_real_virtual.rst

diff --git a/doc/guides/sample_app_ug/l2_forward_real_virtual.rst b/doc/guides/sample_app_ug/l2_forward_real_virtual.rst
index b459d4e..671d0c7 100644 (file)
--- a/doc/guides/sample_app_ug/l2_forward_real_virtual.rst
+++ b/doc/guides/sample_app_ug/l2_forward_real_virtual.rst
@@ -101,7 +101,7 @@ where,
 
 *   --[no-]mac-updating: Enable or disable MAC addresses updating (enabled by default).
 
 
 *   --[no-]mac-updating: Enable or disable MAC addresses updating (enabled by default).
 

-To run the application in linuxapp environment with 4 lcores, 16 ports and 8 RX queues per lcore and MAC address
+To run the application in linux environment with 4 lcores, 16 ports and 8 RX queues per lcore and MAC address

 updating enabled, issue the command:
 
 .. code-block:: console
 updating enabled, issue the command:
 
 .. code-block:: console


@@ -194,9 +194,6 @@ in the *DPDK Programmer's Guide* - Rel 1.4 EAR and the *DPDK API Reference*.
 
 .. code-block:: c
 
 
 .. code-block:: c
 

-    if (rte_pci_probe() < 0)
-        rte_exit(EXIT_FAILURE, "Cannot probe PCI\n");
-

     /* reset l2fwd_dst_ports */
 
     for (portid = 0; portid < RTE_MAX_ETHPORTS; portid++)
     /* reset l2fwd_dst_ports */
 
     for (portid = 0; portid < RTE_MAX_ETHPORTS; portid++)


@@ -226,12 +223,6 @@ in the *DPDK Programmer's Guide* - Rel 1.4 EAR and the *DPDK API Reference*.
         rte_eth_dev_info_get((uint8_t) portid, &dev_info);
     }
 
         rte_eth_dev_info_get((uint8_t) portid, &dev_info);
     }
 

-Observe that:
-
-*   rte_igb_pmd_init_all() simultaneously registers the driver as a PCI driver and as an Ethernet* Poll Mode Driver.
-
-*   rte_pci_probe() parses the devices on the PCI bus and initializes recognized devices.
-

 The next step is to configure the RX and TX queues.
 For each port, there is only one RX queue (only one lcore is able to poll a given port).
 The number of TX queues depends on the number of available lcores.
 The next step is to configure the RX and TX queues.
 For each port, there is only one RX queue (only one lcore is able to poll a given port).
 The number of TX queues depends on the number of available lcores.


@@ -245,25 +236,6 @@ The rte_eth_dev_configure() function is used to configure the number of queues f
             "err=%d, port=%u\n",
             ret, portid);
 
             "err=%d, port=%u\n",
             ret, portid);
 

-The global configuration is stored in a static structure:
-
-.. code-block:: c
-
-    static const struct rte_eth_conf port_conf = {
-        .rxmode = {
-            .split_hdr_size = 0,
-            .header_split = 0,   /**< Header Split disabled */
-            .hw_ip_checksum = 0, /**< IP checksum offload disabled */
-            .hw_vlan_filter = 0, /**< VLAN filtering disabled */
-            .jumbo_frame = 0,    /**< Jumbo Frame Support disabled */
-            .hw_strip_crc= 0,    /**< CRC stripped by hardware */
-        },
-
-        .txmode = {
-            .mq_mode = ETH_DCB_NONE
-        },
-    };
-

 .. _l2_fwd_app_rx_init:
 
 RX Queue Initialization
 .. _l2_fwd_app_rx_init:
 
 RX Queue Initialization


@@ -300,18 +272,6 @@ The list of queues that must be polled for a given lcore is stored in a private
 The values n_rx_port and rx_port_list[] are used in the main packet processing loop
 (see :ref:`l2_fwd_app_rx_tx_packets`).
 
 The values n_rx_port and rx_port_list[] are used in the main packet processing loop
 (see :ref:`l2_fwd_app_rx_tx_packets`).
 

-The global configuration for the RX queues is stored in a static structure:
-
-.. code-block:: c
-
-    static const struct rte_eth_rxconf rx_conf = {
-        .rx_thresh = {
-            .pthresh = RX_PTHRESH,
-            .hthresh = RX_HTHRESH,
-            .wthresh = RX_WTHRESH,
-        },
-    };
-

 .. _l2_fwd_app_tx_init:
 
 TX Queue Initialization
 .. _l2_fwd_app_tx_init:
 
 TX Queue Initialization


@@ -386,13 +346,13 @@ Naturally, the number of ports in the portmask must be even, otherwise, the appl
     static void
     l2fwd_simple_forward(struct rte_mbuf *m, unsigned portid)
     {
     static void
     l2fwd_simple_forward(struct rte_mbuf *m, unsigned portid)
     {

-        struct ether_hdr *eth;
+        struct rte_ether_hdr *eth;

         void *tmp;
         unsigned dst_port;
 
         dst_port = l2fwd_dst_ports[portid];
 
         void *tmp;
         unsigned dst_port;
 
         dst_port = l2fwd_dst_ports[portid];
 

-        eth = rte_pktmbuf_mtod(m, struct ether_hdr *);
+        eth = rte_pktmbuf_mtod(m, struct rte_ether_hdr *);

 
         /* 02:00:00:00:00:xx */
 
 
         /* 02:00:00:00:00:xx */
 


@@ -402,7 +362,7 @@ Naturally, the number of ports in the portmask must be even, otherwise, the appl
 
         /* src addr */
 
 
         /* src addr */
 

-        ether_addr_copy(&l2fwd_ports_eth_addr[dst_port], &eth->s_addr);
+        rte_ether_addr_copy(&l2fwd_ports_eth_addr[dst_port], &eth->s_addr);

 
         l2fwd_send_packet(m, (uint8_t) dst_port);
     }
 
         l2fwd_send_packet(m, (uint8_t) dst_port);
     }