doc: fix typos in flow API guide

[dpdk.git] / doc / guides / testpmd_app_ug / run_app.rst

diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst
index 4495ed0..e7db520 100644 (file)
--- a/doc/guides/testpmd_app_ug/run_app.rst
+++ b/doc/guides/testpmd_app_ug/run_app.rst
@@ -22,7 +22,7 @@ They must be separated from the EAL options, shown in the previous section, with
 
     sudo ./testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2
 
 
     sudo ./testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2
 

-The commandline options are:
+The command line options are:

 
 *   ``-i, --interactive``
 
 
 *   ``-i, --interactive``
 


@@ -121,12 +121,24 @@ The commandline options are:
        XX:XX:XX:XX:XX:02
        ...
 
        XX:XX:XX:XX:XX:02
        ...
 

-

 *   ``--eth-peer=N,XX:XX:XX:XX:XX:XX``
 
     Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N,
     where 0 <= N < ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
 
 *   ``--eth-peer=N,XX:XX:XX:XX:XX:XX``
 
     Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N,
     where 0 <= N < ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
 

+*   ``--tx-ip=SRC,DST``
+
+    Set the source and destination IP address used when doing transmit only test.
+    The defaults address values are source 192.18.0.1 and
+    destination 192.18.0.2. These are special purpose addresses
+    reserved for benchmarking (RFC 2544).
+
+*   ``--tx-udp=SRC[,DST]``
+
+    Set the source and destination UDP port number for transmit test only test.
+    The default port is the port 9 which is defined for the discard protocol
+    (RFC 863).
+

 *   ``--pkt-filter-mode=mode``
 
     Set Flow Director mode where mode is either ``none`` (the default), ``signature`` or ``perfect``.
 *   ``--pkt-filter-mode=mode``
 
     Set Flow Director mode where mode is either ``none`` (the default), ``signature`` or ``perfect``.


@@ -324,6 +336,10 @@ The commandline options are:
     Set TX segment sizes or total packet length. Valid for ``tx-only``
     and ``flowgen`` forwarding modes.
 
     Set TX segment sizes or total packet length. Valid for ``tx-only``
     and ``flowgen`` forwarding modes.
 

+*   ``--txonly-multi-flow``
+
+    Generate multiple flows in txonly mode.
+

 *   ``--disable-link-check``
 
     Disable check on link status when starting/stopping ports.
 *   ``--disable-link-check``
 
     Disable check on link status when starting/stopping ports.


@@ -365,7 +381,7 @@ The commandline options are:
 
 *   ``--hot-plug``
 
 
 *   ``--hot-plug``
 

-    Enable device event monitor machenism for hotplug.
+    Enable device event monitor mechanism for hotplug.

 
 *   ``--vxlan-gpe-port=N``
 
 
 *   ``--vxlan-gpe-port=N``
 


@@ -405,21 +421,26 @@ The commandline options are:
 
 *   ``--noisy-lkup-memory=N``
 
 
 *   ``--noisy-lkup-memory=N``
 

-    Set the size of the noisy neighbour simulation memory buffer in MB to N.
+    Set the size of the noisy neighbor simulation memory buffer in MB to N.

     Only available with the noisy forwarding mode. The default value is 0.
 
 
 *   ``--noisy-lkup-num-reads=N``
 
     Only available with the noisy forwarding mode. The default value is 0.
 
 
 *   ``--noisy-lkup-num-reads=N``
 

-    Set the number of reads to be done in noisy neighbour simulation memory buffer to N.
+    Set the number of reads to be done in noisy neighbor simulation memory buffer to N.

     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--noisy-lkup-num-writes=N``
 
     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--noisy-lkup-num-writes=N``
 

-    Set the number of writes to be done in noisy neighbour simulation memory buffer to N.
+    Set the number of writes to be done in noisy neighbor simulation memory buffer to N.

     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--noisy-lkup-num-reads-writes=N``
 
     Only available with the noisy forwarding mode. The default value is 0.
 
 *   ``--noisy-lkup-num-reads-writes=N``
 

-    Set the number of r/w accesses to be done in noisy neighbour simulation memory buffer to N.
+    Set the number of r/w accesses to be done in noisy neighbor simulation memory buffer to N.

     Only available with the noisy forwarding mode. The default value is 0.
     Only available with the noisy forwarding mode. The default value is 0.

+
+*   ``--no-iova-contig``
+
+    Enable to create mempool which is not IOVA contiguous. Valid only with --mp-alloc=anon.
+    The default value is 0.