bus/pci: support IOVA as VA in PowerVM LPARs

[dpdk.git] / doc / guides / testpmd_app_ug / run_app.rst

diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst
index 4e5929e..eb48318 100644 (file)
--- a/doc/guides/testpmd_app_ug/run_app.rst
+++ b/doc/guides/testpmd_app_ug/run_app.rst
@@ -20,7 +20,7 @@ They must be separated from the EAL options, shown in the previous section, with
 
 .. code-block:: console
 
 
 .. code-block:: console
 

-    sudo ./testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2
+    sudo ./dpdk-testpmd -l 0-3 -n 4 -- -i --portmask=0x1 --nb-cores=2

 
 The command line options are:
 
 
 The command line options are:
 


@@ -59,13 +59,13 @@ The command line options are:
 *   ``--nb-cores=N``
 
     Set the number of forwarding cores,
 *   ``--nb-cores=N``
 
     Set the number of forwarding cores,

-    where 1 <= N <= "number of cores" or ``CONFIG_RTE_MAX_LCORE`` from the configuration file.
+    where 1 <= N <= "number of cores" or ``RTE_MAX_LCORE`` from the configuration file.

     The default value is 1.
 
 *   ``--nb-ports=N``
 
     Set the number of forwarding ports,
     The default value is 1.
 
 *   ``--nb-ports=N``
 
     Set the number of forwarding ports,

-    where 1 <= N <= "number of ports" on the board or ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
+    where 1 <= N <= "number of ports" on the board or ``RTE_MAX_ETHPORTS`` from the configuration file.

     The default value is the number of ports on the board.
 
 *   ``--coremask=0xXX``
     The default value is the number of ports on the board.
 
 *   ``--coremask=0xXX``


@@ -138,7 +138,7 @@ The command line options are:
 *   ``--eth-peer=N,XX:XX:XX:XX:XX:XX``
 
     Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N,
 *   ``--eth-peer=N,XX:XX:XX:XX:XX:XX``
 
     Set the MAC address ``XX:XX:XX:XX:XX:XX`` of the peer port N,

-    where 0 <= N < ``CONFIG_RTE_MAX_ETHPORTS`` from the configuration file.
+    where 0 <= N < ``RTE_MAX_ETHPORTS``.

 
 *   ``--tx-ip=SRC,DST``
 
 
 *   ``--tx-ip=SRC,DST``
 


@@ -299,6 +299,13 @@ The command line options are:
     If set to 0, driver default is used if defined. Else, if driver
     default is not defined, default of 32 is used.
 
     If set to 0, driver default is used if defined. Else, if driver
     default is not defined, default of 32 is used.
 

+*   ``--flowgen-clones=N``
+
+    Set the number of each packet clones to be sent in `flowgen` mode.
+    Sending clones reduces host CPU load on creating packets and may help
+    in testing extreme speeds or maxing out Tx packet performance.
+    N should be not zero, but less than 'burst' parameter.
+

 *   ``--mbcache=N``
 
     Set the cache of mbuf memory pools to N, where 0 <= N <= 512.
 *   ``--mbcache=N``
 
     Set the cache of mbuf memory pools to N, where 0 <= N <= 512.


@@ -349,14 +356,6 @@ The command line options are:
     Set the transmit RS bit threshold of TX rings to N, where 0 <= N <= value of ``--txd``.
     The default value is 0.
 
     Set the transmit RS bit threshold of TX rings to N, where 0 <= N <= value of ``--txd``.
     The default value is 0.
 

-*   ``--rx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping)]``
-
-    Set the RX queues statistics counters mapping 0 <= mapping <= 15.
-
-*   ``--tx-queue-stats-mapping=(port,queue,mapping)[,(port,queue,mapping)]``
-
-    Set the TX queues statistics counters mapping 0 <= mapping <= 15.
-

 *   ``--no-flush-rx``
 
     Don't flush the RX streams before starting forwarding. Used mainly with the PCAP PMD.
 *   ``--no-flush-rx``
 
     Don't flush the RX streams before starting forwarding. Used mainly with the PCAP PMD.


@@ -385,6 +384,21 @@ The command line options are:
 
     Generate multiple flows in txonly mode.
 
 
     Generate multiple flows in txonly mode.
 

+*   ``--eth-link-speed``
+
+    Set a forced link speed to the ethernet port::
+
+       10 - 10Mbps (not supported)
+       100 - 100Mbps (not supported)
+       1000 - 1Gbps
+       10000 - 10Gbps
+       25000 - 25Gbps
+       40000 - 40Gbps
+       50000 - 50Gbps
+       100000 - 100Gbps
+       200000 - 200Gbps
+       ...
+

 *   ``--disable-link-check``
 
     Disable check on link status when starting/stopping ports.
 *   ``--disable-link-check``
 
     Disable check on link status when starting/stopping ports.


@@ -524,8 +538,10 @@ The command line options are:
 
 *   ``--hairpin-mode=0xXX``
 
 
 *   ``--hairpin-mode=0xXX``
 

-    Set the hairpin port mode with bitmask, only valid when hairpin queues number is set.
-    bit 4 - explicit Tx flow rule
-    bit 1 - two hairpin ports paired
-    bit 0 - two hairpin ports loop
+    Set the hairpin port mode with bitmask, only valid when hairpin queues number is set::
+
+       bit 4 - explicit Tx flow rule
+       bit 1 - two hairpin ports paired
+       bit 0 - two hairpin ports loop
+

     The default value is 0. Hairpin will use single port mode and implicit Tx flow mode.
     The default value is 0. Hairpin will use single port mode and implicit Tx flow mode.