+ /* Reserved field, set to 0 */
+ /*
+ * When set to 1, the parallel detection is used to determine
+ * the speed of the link partner. Parallel detection is used
+ * when a autonegotiation capable device is connected to a link
+ * parter that is not capable of autonegotiation.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT UINT32_C(0x1)
+ /* Reserved field, set to 0 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK UINT32_C(0xfe)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1
+ uint16_t link_partner_adv_speeds;
+ /*
+ * The advertised speeds for the port by the link partner. Each
+ * advertised speed will be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \
+ UINT32_C(0x2000)
+ uint8_t link_partner_adv_auto_mode;
+ /*
+ * The advertised autoneg for the port by the link partner. This
+ * field is deprecated and should be set to 0.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \
+ UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
+ UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
+ UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
+ UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
+ UINT32_C(0x4)
+ uint8_t link_partner_adv_pause;
+ /* The advertised pause settings on the port by the link partner. */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
+ UINT32_C(0x2)
+ uint16_t adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is used to advertise
+ * speeds during autonegotiation when EEE is enabled. This field
+ * is valid only when eee_enabled flags is set to 1. The speeds
+ * specified in this field shall be a subset of speeds specified
+ * in auto_link_speed_mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t link_partner_adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is advertised by the
+ * link partner when EEE is enabled. This field is valid only
+ * when eee_enabled flags is set to 1.
+ */
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint32_t xcvr_identifier_type_tx_lpi_timer;
+ /* This value represents transceiver identifier type. */
+ /*
+ * Current setting of TX LPI timer in microseconds. This field
+ * is valid only when_eee_enabled flag is set to 1 and
+ * tx_lpi_enabled is set to 1.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
+ /* This value represents transceiver identifier type. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT 24
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 24)
+ /* SFP/SFP+/SFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
+ (UINT32_C(0x3) << 24)
+ /* QSFP */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
+ (UINT32_C(0xc) << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
+ (UINT32_C(0xd) << 24)
+ /* QSFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
+ (UINT32_C(0x11) << 24)
+ uint16_t fec_cfg;
+ /*
+ * This value represents the current configuration of Forward
+ * Error Correction (FEC) on the port.
+ */
+ /*
+ * When set to 1, then FEC is not supported on this port. If
+ * this flag is set to 1, then all other FEC configuration flags
+ * shall be ignored. When set to 0, then FEC is supported as
+ * indicated by other configuration flags. If no cable is
+ * attached and the HWRM does not yet know the FEC capability,
+ * then the HWRM shall set this flag to 1 when reporting FEC
+ * capability.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * When set to 1, then FEC autonegotiation is supported on this
+ * port. When set to 0, then FEC autonegotiation is not
+ * supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * When set to 1, then FEC autonegotiation is enabled on this
+ * port. When set to 0, then FEC autonegotiation is disabled if
+ * supported. This flag should be ignored if FEC autonegotiation
+ * is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED \
+ UINT32_C(0x4)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * disabled if supported. This flag should be ignored if FEC
+ * CLAUSE 74 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED \
+ UINT32_C(0x10)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is supported
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is enabled
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is disabled if supported. This flag should be
+ * ignored if FEC CLAUSE 91 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED \
+ UINT32_C(0x40)
+ uint8_t unused_1;
+ uint8_t unused_2;
+ char phy_vendor_name[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string representing PHY
+ * vendor. If the string is set to null, then the vendor name is
+ * not available.
+ */
+ char phy_vendor_partnumber[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string that identifies
+ * vendor specific part number of the PHY. If the string is set
+ * to null, then the vendor specific part number is not
+ * available.
+ */
+ uint32_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t unused_6;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_qstats */
+/* Description: This function returns per port Ethernet statistics. */
+/* Input (40 bytes) */
+struct hwrm_port_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2[3];
+ uint8_t unused_3;
+ uint64_t tx_stat_host_addr;
+ /* This is the host address where Tx port statistics will be stored */
+ uint64_t rx_stat_host_addr;
+ /* This is the host address where Rx port statistics will be stored */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t tx_stat_size;
+ /* The size of TX port statistics block in bytes. */
+ uint16_t rx_stat_size;
+ /* The size of RX port statistics block in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_clr_stats */
+/*
+ * Description: This function clears per port statistics. The HWRM shall not
+ * allow a VF driver to clear port statistics. The HWRM shall not allow a PF
+ * driver to clear port statistics in a partitioning mode. The HWRM may allow a
+ * PF driver to clear port statistics in the non-partitioning mode.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_qportcfg */
+/*
+ * Description: This function is called by a driver to query queue configuration
+ * of a port. # The HWRM shall at least advertise one queue with lossy service
+ * profile. # The driver shall use this command to query queue ids before
+ * configuring or using any queues. # If a service profile is not set for a
+ * queue, then the driver shall not use that queue without configuring a service
+ * profile for it. # If the driver is not allowed to configure service profiles,
+ * then the driver shall only use queues for which service profiles are pre-
+ * configured.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_qportcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \
+ QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the queue configuration is being
+ * queried. This field is only required when sent by IPC.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_queue_qportcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t max_configurable_queues;
+ /*
+ * The maximum number of queues that can be configured on this
+ * port. Valid values range from 1 through 8.
+ */
+ uint8_t max_configurable_lossless_queues;
+ /*
+ * The maximum number of lossless queues that can be configured
+ * on this port. Valid values range from 0 through 8.
+ */
+ uint8_t queue_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_cfg command. Each bit represents a specific queue
+ * where bit 0 represents queue 0 and bit 7 represents queue 7.
+ * # A value of 0 indicates that the queue is not configurable
+ * by the hwrm_queue_cfg command. # A value of 1 indicates that
+ * the queue is configurable. # A hwrm_queue_cfg command shall
+ * return error when trying to configure a queue not
+ * configurable.
+ */
+ uint8_t queue_cfg_info;
+ /* Information about queue configuration. */
+ /*
+ * If this flag is set to '1', then the queues are configured
+ * asymmetrically on TX and RX sides. If this flag is set to
+ * '0', then the queues are configured symmetrically on TX and
+ * RX sides. For symmetric configuration, the queue
+ * configuration including queue ids and service profiles on the
+ * TX side is the same as the corresponding queue configuration
+ * on the RX side.
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG UINT32_C(0x1)
+ uint8_t queue_pfcenable_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pfcenable_cfg command. Each bit represents a
+ * specific priority where bit 0 represents priority 0 and bit 7
+ * represents priority 7. # A value of 0 indicates that the
+ * priority is not configurable by the hwrm_queue_pfcenable_cfg
+ * command. # A value of 1 indicates that the priority is
+ * configurable. # A hwrm_queue_pfcenable_cfg command shall
+ * return error when trying to configure a priority that is not
+ * configurable.
+ */
+ uint8_t queue_pri2cos_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pri2cos_cfg command. Each bit represents a
+ * specific queue where bit 0 represents queue 0 and bit 7
+ * represents queue 7. # A value of 0 indicates that the queue
+ * is not configurable by the hwrm_queue_pri2cos_cfg command. #
+ * A value of 1 indicates that the queue is configurable. # A
+ * hwrm_queue_pri2cos_cfg command shall return error when trying
+ * to configure a queue that is not configurable.
+ */
+ uint8_t queue_cos2bw_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pri2cos_cfg command. Each bit represents a
+ * specific queue where bit 0 represents queue 0 and bit 7
+ * represents queue 7. # A value of 0 indicates that the queue
+ * is not configurable by the hwrm_queue_pri2cos_cfg command. #
+ * A value of 1 indicates that the queue is configurable. # A
+ * hwrm_queue_pri2cos_cfg command shall return error when trying
+ * to configure a queue not configurable.
+ */
+ uint8_t queue_id0;
+ /*
+ * ID of CoS Queue 0. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id0_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id1;
+ /*
+ * ID of CoS Queue 1. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id1_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id2;
+ /*
+ * ID of CoS Queue 2. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id2_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id3;
+ /*
+ * ID of CoS Queue 3. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id3_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id4;
+ /*
+ * ID of CoS Queue 4. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id4_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id5;
+ /*
+ * ID of CoS Queue 5. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id5_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id6;
+ /*
+ * ID of CoS Queue 6. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id6_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id7;
+ /*
+ * ID of CoS Queue 7. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id7_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_alloc */
+/*
+ * Description: This VNIC is a resource in the RX side of the chip that is used
+ * to represent a virtual host "interface". # At the time of VNIC allocation or
+ * configuration, the function can specify whether it wants the requested VNIC
+ * to be the default VNIC for the function or not. # If a function requests
+ * allocation of a VNIC for the first time and a VNIC is successfully allocated
+ * by the HWRM, then the HWRM shall make the allocated VNIC as the default VNIC
+ * for that function. # The default VNIC shall be used for the default action
+ * for a partition or function. # For each VNIC allocated on a function, a
+ * mapping on the RX side to map the allocated VNIC to source virtual interface
+ * shall be performed by the HWRM. This should be hidden to the function driver
+ * requesting the VNIC allocation. This enables broadcast/multicast replication
+ * with source knockout. # If multicast replication with source knockout is
+ * enabled, then the internal VNIC to SVIF mapping data structures shall be
+ * programmed at the time of VNIC allocation.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', this VNIC is requested to be the
+ * default VNIC for this function.
+ */
+ #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_free */
+/*
+ * Description: Free a VNIC resource. Idle any resources associated with the
+ * VNIC as well as the VNIC. Reset and release all resources associated with the
+ * VNIC.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_cfg */
+/* Description: Configure the RX VNIC structure. */
+/* Input (40 bytes) */
+struct hwrm_vnic_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is requested to be the default
+ * VNIC for the function.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is being configured to strip
+ * VLAN in the RX path. If set to '0', then VLAN stripping is
+ * disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is being configured to buffer
+ * receive packets in the hardware until the host posts new
+ * receive buffers. If set to '0', then bd_stall is being
+ * configured to be disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is being configured to receive
+ * both RoCE and non-RoCE traffic. If set to '0', then this VNIC
+ * is not configured to be operating in dual VNIC mode.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is requested to be
+ * configured to receive only RoCE traffic. If this flag is set
+ * to '0', then this flag shall be ignored by the HWRM. If
+ * roce_dual_vnic_mode flag is set to '1', then the HWRM client
+ * shall not set this flag to '1'.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where exact match is
+ * used to direct packets to a VNIC with one destination ring
+ * group only, there is no need to configure RSS indirection
+ * table for that VNIC as only one destination ring group is
+ * used. This flag is used to enable a mode where RSS is enabled
+ * in the VNIC using a RSS context for computing RSS hash but
+ * the RSS indirection table is not configured using
+ * hwrm_vnic_rss_cfg. If this mode is enabled, then the driver
+ * should not program RSS indirection table for the RSS context
+ * that is used for computing RSS hash only.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_RSS_DFLT_CR_MODE UINT32_C(0x20)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the dflt_ring_grp field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP UINT32_C(0x1)
+ /* This bit must be '1' for the rss_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE UINT32_C(0x2)
+ /* This bit must be '1' for the cos_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE UINT32_C(0x4)
+ /* This bit must be '1' for the lb_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE UINT32_C(0x8)
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU UINT32_C(0x10)
+ uint16_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t dflt_ring_grp;
+ /*
+ * Default Completion ring for the VNIC. This ring will be
+ * chosen if packet does not match any RSS rules and if there is
+ * no COS rule.
+ */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All
+ * Fs) if there is no LB rule.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the vnic. Each vnic is associated
+ * with a function. The vnic mru value overwrites the mru
+ * setting of the associated function. The HWRM shall make sure
+ * that vnic mru does not exceed the mru of the port the
+ * function is associated with.
+ */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_qcfg */
+/*
+ * Description: Query the RX VNIC structure. This function can be used by a PF
+ * driver to query its own VNIC resource or VNIC resource of its child VF. This
+ * function can also be used by a VF driver to query its own VNIC resource.
+ */
+/* Input (32 bytes) */
+struct hwrm_vnic_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id_valid field to be configured. */
+ #define HWRM_VNIC_QCFG_INPUT_ENABLES_VF_ID_VALID UINT32_C(0x1)
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t vf_id;
+ /* ID of Virtual Function whose VNIC resource is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_vnic_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t dflt_ring_grp;
+ /* Default Completion ring for the VNIC. */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All
+ * Fs) if there is no LB rule.
+ */
+ uint16_t mru;
+ /* The maximum receive unit of the vnic. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is the default VNIC for the
+ * function.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is configured to strip VLAN in
+ * the RX path. If set to '0', then VLAN stripping is disabled
+ * on this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is configured to buffer
+ * receive packets in the hardware until the host posts new
+ * receive buffers. If set to '0', then bd_stall is disabled on
+ * this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is configured to receive both
+ * RoCE and non-RoCE traffic. If set to '0', then this VNIC is
+ * not configured to operate in dual VNIC mode.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is configured to
+ * receive only RoCE traffic. When this flag is set to '0', the
+ * VNIC is not configured to receive only RoCE traffic. If
+ * roce_dual_vnic_mode flag and this flag both are set to '1',
+ * then it is an invalid configuration of the VNIC. The HWRM
+ * should not allow that type of mis-configuration by HWRM
+ * clients.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where exact match is
+ * used to direct packets to a VNIC with one destination ring
+ * group only, there is no need to configure RSS indirection
+ * table for that VNIC as only one destination ring group is
+ * used. When this bit is set to '1', then the VNIC is enabled
+ * in a mode where RSS is enabled in the VNIC using a RSS
+ * context for computing RSS hash but the RSS indirection table
+ * is not configured.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_RSS_DFLT_CR_MODE UINT32_C(0x20)
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cfg */
+/* Description: This function is used to enable RSS configuration. */
+/* Input (48 bytes) */
+struct hwrm_vnic_rss_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 UINT32_C(0x1)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20)
+ uint32_t unused_0;
+ uint64_t ring_grp_tbl_addr;
+ /* This is the address for rss ring group table */
+ uint64_t hash_key_tbl_addr;
+ /* This is the address for rss hash key table */
+ uint16_t rss_ctx_idx;
+ /* Index to the rss indirection table. */
+ uint16_t unused_1[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_plcmodes_cfg */
+/*
+ * Description: This function can be used to set placement mode configuration of
+ * the VNIC.
+ */
+/* Input (40 bytes) */
+
+struct hwrm_vnic_plcmodes_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to use regular
+ * placement algorithm. By default, the regular placement algorithm
+ * shall be enabled on the VNIC.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_REGULAR_PLACEMENT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC shall be configured use the jumbo
+ * placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_JUMBO_PLACEMENT \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for IPv4 packets according to the following rules: # If
+ * the packet is identified as TCP/IPv4, then the packet is split at the
+ * beginning of the TCP payload. # If the packet is identified as
+ * UDP/IPv4, then the packet is split at the beginning of UDP payload. #
+ * If the packet is identified as non-TCP and non-UDP IPv4 packet, then
+ * the packet is split at the beginning of the upper layer protocol
+ * header carried in the IPv4 packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for IPv6 packets according to the following rules: # If
+ * the packet is identified as TCP/IPv6, then the packet is split at the
+ * beginning of the TCP payload. # If the packet is identified as
+ * UDP/IPv6, then the packet is split at the beginning of UDP payload. #
+ * If the packet is identified as non-TCP and non-UDP IPv6 packet, then
+ * the packet is split at the beginning of the upper layer protocol
+ * header carried in the IPv6 packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for FCoE packets at the beginning of FC payload.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_FCOE UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for RoCE packets at the beginning of RoCE payload (after
+ * BTH/GRH headers).
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_ROCE UINT32_C(0x20)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the jumbo_thresh_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_JUMBO_THRESH_VALID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the hds_offset_valid field to be configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_OFFSET_VALID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the hds_threshold_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_THRESHOLD_VALID \
+ UINT32_C(0x4)
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t jumbo_thresh;
+ /*
+ * When jumbo placement algorithm is enabled, this value is used to
+ * determine the threshold for jumbo placement. Packets with length
+ * larger than this value will be placed according to the jumbo
+ * placement algorithm.
+ */
+ uint16_t hds_offset;
+ /*
+ * This value is used to determine the offset into packet buffer where
+ * the split data (payload) will be placed according to one of of HDS
+ * placement algorithm. The lengths of packet buffers provided for split
+ * data shall be larger than this value.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When one of the HDS placement algorithm is enabled, this value is
+ * used to determine the threshold for HDS placement. Packets with
+ * length larger than this value will be placed according to the HDS
+ * placement algorithm. This value shall be in multiple of 4 bytes.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+
+struct hwrm_vnic_plcmodes_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_plcmodes_qcfg */
+/*
+ * Description: This function can be used to query placement mode configuration
+ * of the VNIC.
+ */
+/* Input (24 bytes) */
+
+struct hwrm_vnic_plcmodes_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+
+struct hwrm_vnic_plcmodes_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is configured to use regular placement
+ * algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_REGULAR_PLACEMENT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is configured to use the jumbo
+ * placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_JUMBO_PLACEMENT \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for IPv4 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for IPv6 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for FCoE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_FCOE UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for RoCE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_ROCE UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is configured to be the default VNIC
+ * of the requesting function.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_DFLT_VNIC UINT32_C(0x40)
+ uint16_t jumbo_thresh;
+ /*
+ * When jumbo placement algorithm is enabled, this value is used to
+ * determine the threshold for jumbo placement. Packets with length
+ * larger than this value will be placed according to the jumbo
+ * placement algorithm.
+ */
+ uint16_t hds_offset;
+ /*
+ * This value is used to determine the offset into packet buffer where
+ * the split data (payload) will be placed according to one of of HDS
+ * placement algorithm. The lengths of packet buffers provided for split
+ * data shall be larger than this value.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When one of the HDS placement algorithm is enabled, this value is
+ * used to determine the threshold for HDS placement. Packets with
+ * length larger than this value will be placed according to the HDS
+ * placement algorithm. This value shall be in multiple of 4 bytes.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cos_lb_ctx_alloc */
+/* Description: This function is used to allocate COS/Load Balance context. */
+/* Input (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t rss_cos_lb_ctx_id;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));