+/* HWRM Asynchronous Event Completion Record (16 bytes) */
+struct hwrm_async_event_cmpl {
+ uint16_t type;
+ /* unused1 is 10 b */
+ /*
+ * This field indicates the exact type of the completion. By
+ * convention, the LSB identifies the length of the record in
+ * 16B units. Even values indicate 16B records. Odd values
+ * indicate 32B records.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_MASK UINT32_C(0x3f)
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_SFT 0
+ /* HWRM Asynchronous Event Information */
+ #define HWRM_ASYNC_EVENT_CMPL_TYPE_HWRM_ASYNC_EVENT UINT32_C(0x2e)
+ /* unused1 is 10 b */
+ uint16_t event_id;
+ /* Identifiers of events. */
+ /* Link status changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_STATUS_CHANGE UINT32_C(0x0)
+ /* Link MTU changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_MTU_CHANGE UINT32_C(0x1)
+ /* Link speed changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CHANGE UINT32_C(0x2)
+ /* DCB Configuration changed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_DCB_CONFIG_CHANGE UINT32_C(0x3)
+ /* Port connection not allowed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_CONN_NOT_ALLOWED UINT32_C(0x4)
+ /* Link speed configuration was not allowed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_NOT_ALLOWED \
+ UINT32_C(0x5)
+ /* Link speed configuration change */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_LINK_SPEED_CFG_CHANGE UINT32_C(0x6)
+ /* Port PHY configuration change */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PORT_PHY_CFG_CHANGE UINT32_C(0x7)
+ /* Function driver unloaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_UNLOAD UINT32_C(0x10)
+ /* Function driver loaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_DRVR_LOAD UINT32_C(0x11)
+ /* Function FLR related processing has completed */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_FUNC_FLR_PROC_CMPLT UINT32_C(0x12)
+ /* PF driver unloaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_UNLOAD UINT32_C(0x20)
+ /* PF driver loaded */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_DRVR_LOAD UINT32_C(0x21)
+ /* VF Function Level Reset (FLR) */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_FLR UINT32_C(0x30)
+ /* VF MAC Address Change */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_MAC_ADDR_CHANGE UINT32_C(0x31)
+ /* PF-VF communication channel status change. */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_PF_VF_COMM_STATUS_CHANGE \
+ UINT32_C(0x32)
+ /* VF Configuration Change */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_VF_CFG_CHANGE UINT32_C(0x33)
+ /* HWRM Error */
+ #define HWRM_ASYNC_EVENT_CMPL_EVENT_ID_HWRM_ERROR UINT32_C(0xff)
+ uint32_t event_data2;
+ /* Event specific data */
+ uint8_t opaque_v;
+ /* opaque is 7 b */
+ /*
+ * This value is written by the NIC such that it will be
+ * different for each pass through the completion queue. The
+ * even passes will write 1. The odd passes will write 0.
+ */
+ #define HWRM_ASYNC_EVENT_CMPL_V UINT32_C(0x1)
+ /* opaque is 7 b */
+ #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_MASK UINT32_C(0xfe)
+ #define HWRM_ASYNC_EVENT_CMPL_OPAQUE_SFT 1
+ uint8_t timestamp_lo;
+ /* 8-lsb timestamp from POR (100-msec resolution) */
+ uint16_t timestamp_hi;
+ /* 16-lsb timestamp from POR (100-msec resolution) */
+ uint32_t event_data1;
+ /* Event specific data */
+} __attribute__((packed));
+
+/* hwrm_ver_get */
+/*
+ * Description: This function is called by a driver to determine the HWRM
+ * interface version supported by the HWRM firmware, the version of HWRM
+ * firmware implementation, the name of HWRM firmware, the versions of other
+ * embedded firmwares, and the names of other embedded firmwares, etc. Any
+ * interface or firmware version with major = 0, minor = 0, and update = 0 shall
+ * be considered an invalid version.
+ */
+/* Input (24 bytes) */
+struct hwrm_ver_get_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t hwrm_intf_maj;
+ /*
+ * This field represents the major version of HWRM interface
+ * specification supported by the driver HWRM implementation.
+ * The interface major version is intended to change only when
+ * non backward compatible changes are made to the HWRM
+ * interface specification.
+ */
+ uint8_t hwrm_intf_min;
+ /*
+ * This field represents the minor version of HWRM interface
+ * specification supported by the driver HWRM implementation. A
+ * change in interface minor version is used to reflect
+ * significant backward compatible modification to HWRM
+ * interface specification. This can be due to addition or
+ * removal of functionality. HWRM interface specifications with
+ * the same major version but different minor versions are
+ * compatible.
+ */
+ uint8_t hwrm_intf_upd;
+ /*
+ * This field represents the update version of HWRM interface
+ * specification supported by the driver HWRM implementation.
+ * The interface update version is used to reflect minor changes
+ * or bug fixes to a released HWRM interface specification.
+ */
+ uint8_t unused_0[5];
+} __attribute__((packed));
+
+/* Output (128 bytes) */
+struct hwrm_ver_get_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t hwrm_intf_maj;
+ /*
+ * This field represents the major version of HWRM interface
+ * specification supported by the HWRM implementation. The
+ * interface major version is intended to change only when non
+ * backward compatible changes are made to the HWRM interface
+ * specification. A HWRM implementation that is compliant with
+ * this specification shall provide value of 1 in this field.
+ */
+ uint8_t hwrm_intf_min;
+ /*
+ * This field represents the minor version of HWRM interface
+ * specification supported by the HWRM implementation. A change
+ * in interface minor version is used to reflect significant
+ * backward compatible modification to HWRM interface
+ * specification. This can be due to addition or removal of
+ * functionality. HWRM interface specifications with the same
+ * major version but different minor versions are compatible. A
+ * HWRM implementation that is compliant with this specification
+ * shall provide value of 2 in this field.
+ */
+ uint8_t hwrm_intf_upd;
+ /*
+ * This field represents the update version of HWRM interface
+ * specification supported by the HWRM implementation. The
+ * interface update version is used to reflect minor changes or
+ * bug fixes to a released HWRM interface specification. A HWRM
+ * implementation that is compliant with this specification
+ * shall provide value of 2 in this field.
+ */
+ uint8_t hwrm_intf_rsvd;
+ uint8_t hwrm_fw_maj;
+ /*
+ * This field represents the major version of HWRM firmware. A
+ * change in firmware major version represents a major firmware
+ * release.
+ */
+ uint8_t hwrm_fw_min;
+ /*
+ * This field represents the minor version of HWRM firmware. A
+ * change in firmware minor version represents significant
+ * firmware functionality changes.
+ */
+ uint8_t hwrm_fw_bld;
+ /*
+ * This field represents the build version of HWRM firmware. A
+ * change in firmware build version represents bug fixes to a
+ * released firmware.
+ */
+ uint8_t hwrm_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version of the HWRM
+ * firmware.
+ */
+ uint8_t mgmt_fw_maj;
+ /*
+ * This field represents the major version of mgmt firmware. A
+ * change in major version represents a major release.
+ */
+ uint8_t mgmt_fw_min;
+ /*
+ * This field represents the minor version of mgmt firmware. A
+ * change in minor version represents significant functionality
+ * changes.
+ */
+ uint8_t mgmt_fw_bld;
+ /*
+ * This field represents the build version of mgmt firmware. A
+ * change in update version represents bug fixes.
+ */
+ uint8_t mgmt_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version
+ */
+ uint8_t netctrl_fw_maj;
+ /*
+ * This field represents the major version of network control
+ * firmware. A change in major version represents a major
+ * release.
+ */
+ uint8_t netctrl_fw_min;
+ /*
+ * This field represents the minor version of network control
+ * firmware. A change in minor version represents significant
+ * functionality changes.
+ */
+ uint8_t netctrl_fw_bld;
+ /*
+ * This field represents the build version of network control
+ * firmware. A change in update version represents bug fixes.
+ */
+ uint8_t netctrl_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version
+ */
+ uint32_t dev_caps_cfg;
+ /*
+ * This field is used to indicate device's capabilities and
+ * configurations.
+ */
+ /*
+ * If set to 1, then secure firmware update behavior is
+ * supported. If set to 0, then secure firmware update behavior
+ * is not supported.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SECURE_FW_UPD_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * If set to 1, then firmware based DCBX agent is supported. If
+ * set to 0, then firmware based DCBX agent capability is not
+ * supported on this device.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_FW_DCBX_AGENT_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, then HWRM short command format is supported. If
+ * set to 0, then HWRM short command format is not supported.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_SUPPORTED \
+ UINT32_C(0x4)
+ /*
+ * If set to 1, then HWRM short command format is required. If
+ * set to 0, then HWRM short command format is not required.
+ */
+ #define HWRM_VER_GET_OUTPUT_DEV_CAPS_CFG_SHORT_CMD_INPUTUIRED \
+ UINT32_C(0x8)
+ uint8_t roce_fw_maj;
+ /*
+ * This field represents the major version of RoCE firmware. A
+ * change in major version represents a major release.
+ */
+ uint8_t roce_fw_min;
+ /*
+ * This field represents the minor version of RoCE firmware. A
+ * change in minor version represents significant functionality
+ * changes.
+ */
+ uint8_t roce_fw_bld;
+ /*
+ * This field represents the build version of RoCE firmware. A
+ * change in update version represents bug fixes.
+ */
+ uint8_t roce_fw_rsvd;
+ /*
+ * This field is a reserved field. This field can be used to
+ * represent firmware branches or customer specific releases
+ * tied to a specific (major,minor,update) version
+ */
+ char hwrm_fw_name[16];
+ /*
+ * This field represents the name of HWRM FW (ASCII chars with
+ * NULL at the end).
+ */
+ char mgmt_fw_name[16];
+ /*
+ * This field represents the name of mgmt FW (ASCII chars with
+ * NULL at the end).
+ */
+ char netctrl_fw_name[16];
+ /*
+ * This field represents the name of network control firmware
+ * (ASCII chars with NULL at the end).
+ */
+ uint32_t reserved2[4];
+ /*
+ * This field is reserved for future use. The responder should
+ * set it to 0. The requester should ignore this field.
+ */
+ char roce_fw_name[16];
+ /*
+ * This field represents the name of RoCE FW (ASCII chars with
+ * NULL at the end).
+ */
+ uint16_t chip_num;
+ /* This field returns the chip number. */
+ uint8_t chip_rev;
+ /* This field returns the revision of chip. */
+ uint8_t chip_metal;
+ /* This field returns the chip metal number. */
+ uint8_t chip_bond_id;
+ /* This field returns the bond id of the chip. */
+ uint8_t chip_platform_type;
+ /*
+ * This value indicates the type of platform used for chip
+ * implementation.
+ */
+ /* ASIC */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_ASIC UINT32_C(0x0)
+ /* FPGA platform of the chip. */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_FPGA UINT32_C(0x1)
+ /* Palladium platform of the chip. */
+ #define HWRM_VER_GET_OUTPUT_CHIP_PLATFORM_TYPE_PALLADIUM UINT32_C(0x2)
+ uint16_t max_req_win_len;
+ /*
+ * This field returns the maximum value of request window that
+ * is supported by the HWRM. The request window is mapped into
+ * device address space using MMIO.
+ */
+ uint16_t max_resp_len;
+ /* This field returns the maximum value of response buffer in bytes. */
+ uint16_t def_req_timeout;
+ /*
+ * This field returns the default request timeout value in
+ * milliseconds.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_reset */
+/*
+ * Description: This command resets a hardware function (PCIe function) and
+ * frees any resources used by the function. This command shall be initiated by
+ * the driver after an FLR has occurred to prepare the function for re-use. This
+ * command may also be initiated by a driver prior to doing it's own
+ * configuration. This command puts the function into the reset state. In the
+ * reset state, global and port related features of the chip are not available.
+ */
+/*
+ * Note: This command will reset a function that has already been disabled or
+ * idled. The command returns all the resources owned by the function so a new
+ * driver may allocate and configure resources normally.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_reset_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id_valid field to be configured. */
+ #define HWRM_FUNC_RESET_INPUT_ENABLES_VF_ID_VALID UINT32_C(0x1)
+ uint16_t vf_id;
+ /*
+ * The ID of the VF that this PF is trying to reset. Only the
+ * parent PF shall be allowed to reset a child VF. A parent PF
+ * driver shall use this field only when a specific child VF is
+ * requested to be reset.
+ */
+ uint8_t func_reset_level;
+ /* This value indicates the level of a function reset. */
+ /*
+ * Reset the caller function and its children
+ * VFs (if any). If no children functions exist,
+ * then reset the caller function only.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETALL UINT32_C(0x0)
+ /* Reset the caller function only */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETME UINT32_C(0x1)
+ /*
+ * Reset all children VFs of the caller function
+ * driver if the caller is a PF driver. It is an
+ * error to specify this level by a VF driver.
+ * It is an error to specify this level by a PF
+ * driver with no children VFs.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETCHILDREN \
+ UINT32_C(0x2)
+ /*
+ * Reset a specific VF of the caller function
+ * driver if the caller is the parent PF driver.
+ * It is an error to specify this level by a VF
+ * driver. It is an error to specify this level
+ * by a PF driver that is not the parent of the
+ * VF that is being requested to reset.
+ */
+ #define HWRM_FUNC_RESET_INPUT_FUNC_RESET_LEVEL_RESETVF UINT32_C(0x3)
+ uint8_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_reset_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qcaps */
+/*
+ * Description: This command returns capabilities of a function. The input FID
+ * value is used to indicate what function is being queried. This allows a
+ * physical function driver to query virtual functions that are children of the
+ * physical function. The output FID value is needed to configure Rings and
+ * MSI-X vectors so their DMA operations appear correctly on the PCI bus.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (80 bytes) */
+struct hwrm_func_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port that this function is associated with. Valid
+ * only for the PF. 0xFF... (All Fs) if this function is not
+ * associated with any port. 0xFF... (All Fs) if this function
+ * is called from a VF.
+ */
+ uint32_t flags;
+ /* If 1, then Push mode is supported on this function. */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED UINT32_C(0x1)
+ /*
+ * If 1, then the global MSI-X auto-masking is enabled for the
+ * device.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING \
+ UINT32_C(0x2)
+ /*
+ * If 1, then the Precision Time Protocol (PTP) processing is
+ * supported on this function. The HWRM should enable PTP on
+ * only a single Physical Function (PF) per port.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED UINT32_C(0x4)
+ /*
+ * If 1, then RDMA over Converged Ethernet (RoCE) v1 is
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V1_SUPPORTED UINT32_C(0x8)
+ /*
+ * If 1, then RDMA over Converged Ethernet (RoCE) v2 is
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V2_SUPPORTED UINT32_C(0x10)
+ /*
+ * If 1, then control and configuration of WoL magic packet are
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_MAGICPKT_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * If 1, then control and configuration of bitmap pattern packet
+ * are supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_BMP_SUPPORTED UINT32_C(0x40)
+ /*
+ * If set to 1, then the control and configuration of rate limit
+ * of an allocated TX ring on the queried function is supported.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_RING_RL_SUPPORTED UINT32_C(0x80)
+ /*
+ * If 1, then control and configuration of minimum and maximum
+ * bandwidths are supported on the queried function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_BW_CFG_SUPPORTED UINT32_C(0x100)
+ /*
+ * If the query is for a VF, then this flag shall be ignored. If
+ * this query is for a PF and this flag is set to 1, then the PF
+ * has the capability to set the rate limits on the TX rings of
+ * its children VFs. If this query is for a PF and this flag is
+ * set to 0, then the PF does not have the capability to set the
+ * rate limits on the TX rings of its children VFs.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_TX_RING_RL_SUPPORTED \
+ UINT32_C(0x200)
+ /*
+ * If the query is for a VF, then this flag shall be ignored. If
+ * this query is for a PF and this flag is set to 1, then the PF
+ * has the capability to set the minimum and/or maximum
+ * bandwidths for its children VFs. If this query is for a PF
+ * and this flag is set to 0, then the PF does not have the
+ * capability to set the minimum or maximum bandwidths for its
+ * children VFs.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_BW_CFG_SUPPORTED UINT32_C(0x400)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is supported on the
+ * queried function. If set to 0, then standard TX ring mode is
+ * not available on the queried function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_STD_TX_RING_MODE_SUPPORTED \
+ UINT32_C(0x800)
+ uint8_t mac_address[6];
+ /*
+ * This value is current MAC address configured for this
+ * function. A value of 00-00-00-00-00-00 indicates no MAC
+ * address is currently configured.
+ */
+ uint16_t max_rsscos_ctx;
+ /*
+ * The maximum number of RSS/COS contexts that can be allocated
+ * to the function.
+ */
+ uint16_t max_cmpl_rings;
+ /*
+ * The maximum number of completion rings that can be allocated
+ * to the function.
+ */
+ uint16_t max_tx_rings;
+ /*
+ * The maximum number of transmit rings that can be allocated to
+ * the function.
+ */
+ uint16_t max_rx_rings;
+ /*
+ * The maximum number of receive rings that can be allocated to
+ * the function.
+ */
+ uint16_t max_l2_ctxs;
+ /*
+ * The maximum number of L2 contexts that can be allocated to
+ * the function.
+ */
+ uint16_t max_vnics;
+ /*
+ * The maximum number of VNICs that can be allocated to the
+ * function.
+ */
+ uint16_t first_vf_id;
+ /*
+ * The identifier for the first VF enabled on a PF. This is
+ * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
+ * this command is called on a PF with SR-IOV disabled or on a
+ * VF.
+ */
+ uint16_t max_vfs;
+ /*
+ * The maximum number of VFs that can be allocated to the
+ * function. This is valid only on the PF with SR-IOV enabled.
+ * 0xFF... (All Fs) if this command is called on a PF with SR-
+ * IOV disabled or on a VF.
+ */
+ uint16_t max_stat_ctx;
+ /*
+ * The maximum number of statistic contexts that can be
+ * allocated to the function.
+ */
+ uint32_t max_encap_records;
+ /*
+ * The maximum number of Encapsulation records that can be
+ * offloaded by this function.
+ */
+ uint32_t max_decap_records;
+ /*
+ * The maximum number of decapsulation records that can be
+ * offloaded by this function.
+ */
+ uint32_t max_tx_em_flows;
+ /*
+ * The maximum number of Exact Match (EM) flows that can be
+ * offloaded by this function on the TX side.
+ */
+ uint32_t max_tx_wm_flows;
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be
+ * offloaded by this function on the TX side.
+ */
+ uint32_t max_rx_em_flows;
+ /*
+ * The maximum number of Exact Match (EM) flows that can be
+ * offloaded by this function on the RX side.
+ */
+ uint32_t max_rx_wm_flows;
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be
+ * offloaded by this function on the RX side.
+ */
+ uint32_t max_mcast_filters;
+ /*
+ * The maximum number of multicast filters that can be supported
+ * by this function on the RX side.
+ */
+ uint32_t max_flow_id;
+ /*
+ * The maximum value of flow_id that can be supported in
+ * completion records.
+ */
+ uint32_t max_hw_ring_grps;
+ /*
+ * The maximum number of HW ring groups that can be supported on
+ * this function.
+ */
+ uint16_t max_sp_tx_rings;
+ /*
+ * The maximum number of strict priority transmit rings that can
+ * be allocated to the function. This number indicates the
+ * maximum number of TX rings that can be assigned strict
+ * priorities out of the maximum number of TX rings that can be
+ * allocated (max_tx_rings) to the function.
+ */
+ uint8_t unused_0;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qcfg */
+/*
+ * Description: This command returns the current configuration of a function.
+ * The input FID value is used to indicate what function is being queried. This
+ * allows a physical function driver to query virtual functions that are
+ * children of the physical function. The output FID value is needed to
+ * configure Rings and MSI-X vectors so their DMA operations appear correctly on
+ * the PCI bus. This command should be called by every driver after
+ * 'hwrm_func_cfg' to get the actual number of resources allocated by the HWRM.
+ * The values returned by hwrm_func_qcfg are the values the driver shall use.
+ * These values may be different than what was originally requested in the
+ * 'hwrm_func_cfg' command.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (72 bytes) */
+struct hwrm_func_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port that this function is associated with.
+ * 0xFF... (All Fs) if this function is not associated with any
+ * port.
+ */
+ uint16_t vlan;
+ /*
+ * This value is the current VLAN setting for this function. The
+ * value of 0 for this field indicates no priority tagging or
+ * VLAN is used. This field's format is same as 802.1Q Tag's Tag
+ * Control Information (TCI) format that includes both Priority
+ * Code Point (PCP) and VLAN Identifier (VID).
+ */
+ uint16_t flags;
+ /*
+ * If 1, then magic packet based Out-Of-Box WoL is enabled on
+ * the port associated with this function.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_MAGICPKT_ENABLED \
+ UINT32_C(0x1)
+ /*
+ * If 1, then bitmap pattern based Out-Of-Box WoL packet is
+ * enabled on the port associated with this function.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_BMP_ENABLED UINT32_C(0x2)
+ /*
+ * If set to 1, then FW based DCBX agent is enabled and running
+ * on the port associated with this function. If set to 0, then
+ * DCBX agent is not running in the firmware.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_DCBX_AGENT_ENABLED \
+ UINT32_C(0x4)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is enabled on the
+ * queried function. If set to 0, then the standard TX ring mode
+ * is disabled on the queried function. In this extended TX ring
+ * resource mode, the minimum and maximum bandwidth settings are
+ * not supported to allow the allocation of TX rings to span
+ * multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_STD_TX_RING_MODE_ENABLED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1 then FW based LLDP agent is enabled and running
+ * on the port associated with this function. If set to 0 then
+ * the LLDP agent is not running in the firmware.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_LLDP_AGENT_ENABLED UINT32_C(0x10)
+ /*
+ * If set to 1, then multi-host mode is active for this
+ * function. If set to 0, then multi-host mode is inactive for
+ * this function or not applicable for this device.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_MULTI_HOST UINT32_C(0x20)
+ uint8_t mac_address[6];
+ /*
+ * This value is current MAC address configured for this
+ * function. A value of 00-00-00-00-00-00 indicates no MAC
+ * address is currently configured.
+ */
+ uint16_t pci_id;
+ /*
+ * This value is current PCI ID of this function. If ARI is
+ * enabled, then it is Bus Number (8b):Function Number(8b).
+ * Otherwise, it is Bus Number (8b):Device Number (4b):Function
+ * Number(4b).
+ */
+ uint16_t alloc_rsscos_ctx;
+ /*
+ * The number of RSS/COS contexts currently allocated to the
+ * function.
+ */
+ uint16_t alloc_cmpl_rings;
+ /*
+ * The number of completion rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_tx_rings;
+ /*
+ * The number of transmit rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_rx_rings;
+ /*
+ * The number of receive rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_l2_ctx;
+ /* The allocated number of L2 contexts to the function. */
+ uint16_t alloc_vnics;
+ /* The allocated number of vnics to the function. */
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. For rings
+ * allocated on this function, this default value is used if
+ * ring MTU is not specified.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. For vnics allocated
+ * on this function, this default value is used if vnic MRU is
+ * not specified.
+ */
+ uint16_t stat_ctx_id;
+ /* The statistics context assigned to a function. */
+ uint8_t port_partition_type;
+ /*
+ * The HWRM shall return Unknown value for this field when this
+ * command is used to query VF's configuration.
+ */
+ /* Single physical function */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_SPF UINT32_C(0x0)
+ /* Multiple physical functions */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_MPFS UINT32_C(0x1)
+ /* Network Partitioning 1.0 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_0 UINT32_C(0x2)
+ /* Network Partitioning 1.5 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_5 UINT32_C(0x3)
+ /* Network Partitioning 2.0 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR2_0 UINT32_C(0x4)
+ /* Unknown */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_UNKNOWN UINT32_C(0xff)
+ uint8_t port_pf_cnt;
+ /*
+ * This field will indicate number of physical functions on this
+ * port_partition. HWRM shall return unavail (i.e. value of 0)
+ * for this field when this command is used to query VF's
+ * configuration or from older firmware that doesn't support
+ * this field.
+ */
+ /* number of PFs is not available */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_UNAVAIL UINT32_C(0x0)
+ uint16_t dflt_vnic_id;
+ /* The default VNIC ID assigned to a function that is being queried. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device. A value of 0 indicates
+ * the minimum bandwidth is not configured.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_LAST \
+ FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device. A value of 0 indicates
+ * that the maximum bandwidth is not configured.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_LAST \
+ FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t evb_mode;
+ /*
+ * This value indicates the Edge virtual bridge mode for the
+ * domain that this function belongs to.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEB UINT32_C(0x1)
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEPA UINT32_C(0x2)
+ uint8_t unused_2;
+ uint16_t alloc_vfs;
+ /*
+ * The number of VFs that are allocated to the function. This is
+ * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
+ * this command is called on a PF with SR-IOV disabled or on a
+ * VF.
+ */
+ uint32_t alloc_mcast_filters;
+ /*
+ * The number of allocated multicast filters for this function
+ * on the RX side.
+ */
+ uint32_t alloc_hw_ring_grps;
+ /* The number of allocated HW ring groups for this function. */
+ uint16_t alloc_sp_tx_rings;
+ /*
+ * The number of strict priority transmit rings out of currently
+ * allocated TX rings to the function (alloc_tx_rings).
+ */
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vlan_qcfg */
+/*
+ * Description: This command should be called by PF driver to get the current
+ * C-TAG, S-TAG and correcponsing PCP and TPID values configured for the
+ * function.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_vlan_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the configuration is for the
+ * requesting function.
+ */
+ uint16_t unused_0[3];
+};
+
+/* Output (40 bytes) */
+struct hwrm_func_vlan_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+ uint16_t stag_vid;
+ /* S-TAG VLAN identifier configured for the function. */
+ uint8_t stag_pcp;
+ /* S-TAG PCP value configured for the function. */
+ uint8_t unused_4;
+ uint16_t stag_tpid;
+ /*
+ * S-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint16_t ctag_vid;
+ /* C-TAG VLAN identifier configured for the function. */
+ uint8_t ctag_pcp;
+ /* C-TAG PCP value configured for the function. */
+ uint8_t unused_5;
+ uint16_t ctag_tpid;
+ /*
+ * C-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint32_t rsvd2;
+ /* Future use. */
+ uint32_t rsvd3;
+ /* Future use. */
+ uint32_t unused_6;
+};
+
+/* hwrm_func_vlan_cfg */
+/*
+ * Description: This command allows PF driver to configure C-TAG, S-TAG and
+ * corresponding PCP and TPID values for a function.
+ */
+/* Input (48 bytes) */
+struct hwrm_func_vlan_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t enables;
+ /* This bit must be '1' for the stag_vid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_VID UINT32_C(0x1)
+ /* This bit must be '1' for the ctag_vid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_VID UINT32_C(0x2)
+ /* This bit must be '1' for the stag_pcp field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_PCP UINT32_C(0x4)
+ /* This bit must be '1' for the ctag_pcp field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_PCP UINT32_C(0x8)
+ /* This bit must be '1' for the stag_tpid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_TPID UINT32_C(0x10)
+ /* This bit must be '1' for the ctag_tpid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_TPID UINT32_C(0x20)
+ uint16_t stag_vid;
+ /* S-TAG VLAN identifier configured for the function. */
+ uint8_t stag_pcp;
+ /* S-TAG PCP value configured for the function. */
+ uint8_t unused_2;
+ uint16_t stag_tpid;
+ /*
+ * S-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint16_t ctag_vid;
+ /* C-TAG VLAN identifier configured for the function. */
+ uint8_t ctag_pcp;
+ /* C-TAG PCP value configured for the function. */
+ uint8_t unused_3;
+ uint16_t ctag_tpid;
+ /*
+ * C-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint32_t rsvd1;
+ /* Future use. */
+ uint32_t rsvd2;
+ /* Future use. */
+ uint32_t unused_4;
+};
+
+/* Output (16 bytes) */
+struct hwrm_func_vlan_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+};
+
+/* hwrm_func_cfg */
+/*
+ * Description: This command allows configuration of a PF by the corresponding
+ * PF driver. This command also allows configuration of a child VF by its parent
+ * PF driver. The input FID value is used to indicate what function is being
+ * configured. This allows a PF driver to configure the PF owned by itself or a
+ * virtual function that is a child of the PF. This command allows to reserve
+ * resources for a VF by its parent PF. To reverse the process, the command
+ * should be called with all enables flags cleared for resources. This will free
+ * allocated resources for the VF and return them to the resource pool. If this
+ * command is requested by a VF driver to configure or reserve resources, then
+ * the HWRM shall fail this command. If default MAC address and/or VLAN are
+ * provided in this command, then the HWRM shall set up appropriate MAC/VLAN
+ * filters for the function that is being configured. If source properties
+ * checks are enabled and default MAC address and/or IP address are provided in
+ * this command, then the HWRM shall set appropriate source property checks
+ * based on provided MAC and/or IP addresses. The parent PF driver should not
+ * set MTU/MRU for a VF using this command. This is to allow MTU/MRU setting by
+ * the VF driver. If the MTU or MRU for a VF is set by the PF driver, then the
+ * HWRM should ignore it. A function's MTU/MRU should be set prior to allocating
+ * RX VNICs or TX rings. A PF driver calls hwrm_func_cfg to allocate resources
+ * for itself or its children VFs. All function drivers shall call hwrm_func_cfg
+ * to reserve resources. A request to hwrm_func_cfg may not be fully granted;
+ * that is, a request for resources may be larger than what can be supported by
+ * the device and the HWRM will allocate the best set of resources available,
+ * but that may be less than requested. If all the amounts requested could not
+ * be fulfilled, the HWRM shall allocate what it could and return a status code
+ * of success. A function driver should call hwrm_func_qcfg immediately after
+ * hwrm_func_cfg to determine what resources were assigned to the configured
+ * function. A call by a PF driver to hwrm_func_cfg to allocate resources for
+ * itself shall only allocate resources for the PF driver to use, not for its
+ * children VFs. Likewise, a call to hwrm_func_qcfg shall return the resources
+ * available for the PF driver to use, not what is available to its children
+ * VFs.
+ */
+/* Input (88 bytes) */
+struct hwrm_func_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function is disabled with source
+ * MAC address check. This is an anti-spoofing check. If this
+ * flag is set, then the function shall be configured to
+ * disallow transmission of frames with the source MAC address
+ * that is configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_DISABLE \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is enabled with source MAC
+ * address check. This is an anti-spoofing check. If this flag
+ * is set, then the function shall be configured to allow
+ * transmission of frames with the source MAC address that is
+ * configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_ENABLE \
+ UINT32_C(0x2)
+ /* reserved */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_MASK UINT32_C(0x1fc)
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_SFT 2
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is requested to be
+ * enabled on the function being configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_ENABLE \
+ UINT32_C(0x200)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then the standard TX ring mode is requested to be
+ * disabled on the function being configured. In this extended
+ * TX ring resource mode, the minimum and maximum bandwidth
+ * settings are not supported to allow the allocation of TX
+ * rings to span multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_DISABLE \
+ UINT32_C(0x400)
+ /*
+ * If this bit is set, virtual mac address configured in this
+ * command will be persistent over warm boot.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_VIRT_MAC_PERSIST UINT32_C(0x800)
+ uint32_t enables;
+ /* This bit must be '1' for the mtu field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MRU UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the num_rsscos_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the num_cmpl_rings field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_CMPL_RINGS UINT32_C(0x8)
+ /* This bit must be '1' for the num_tx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_TX_RINGS UINT32_C(0x10)
+ /* This bit must be '1' for the num_rx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RX_RINGS UINT32_C(0x20)
+ /* This bit must be '1' for the num_l2_ctxs field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_L2_CTXS UINT32_C(0x40)
+ /* This bit must be '1' for the num_vnics field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_VNICS UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the num_stat_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_STAT_CTXS UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the dflt_mac_addr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_MAC_ADDR UINT32_C(0x200)
+ /* This bit must be '1' for the dflt_vlan field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_VLAN UINT32_C(0x400)
+ /* This bit must be '1' for the dflt_ip_addr field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_IP_ADDR UINT32_C(0x800)
+ /* This bit must be '1' for the min_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MIN_BW UINT32_C(0x1000)
+ /* This bit must be '1' for the max_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MAX_BW UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the async_event_cr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ASYNC_EVENT_CR UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the vlan_antispoof_mode field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_VLAN_ANTISPOOF_MODE UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the allowed_vlan_pris field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ALLOWED_VLAN_PRIS UINT32_C(0x10000)
+ /* This bit must be '1' for the evb_mode field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_EVB_MODE UINT32_C(0x20000)
+ /*
+ * This bit must be '1' for the num_mcast_filters field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MCAST_FILTERS UINT32_C(0x40000)
+ /*
+ * This bit must be '1' for the num_hw_ring_grps field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS UINT32_C(0x80000)
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. The HWRM
+ * should make sure that the mtu of the function does not exceed
+ * the mtu of the physical port that this function is associated
+ * with. In addition to configuring mtu per function, it is
+ * possible to configure mtu per transmit ring. By default, the
+ * mtu of each transmit ring associated with a function is equal
+ * to the mtu of the function. The HWRM should make sure that
+ * the mtu of each transmit ring that is assigned to a function
+ * has a valid mtu.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. The HWRM should
+ * make sure that the mru of the function does not exceed the
+ * mru of the physical port that this function is associated
+ * with. In addition to configuring mru per function, it is
+ * possible to configure mru per vnic. By default, the mru of
+ * each vnic associated with a function is equal to the mru of
+ * the function. The HWRM should make sure that the mru of each
+ * vnic that is assigned to a function has a valid mru.
+ */
+ uint16_t num_rsscos_ctxs;
+ /* The number of RSS/COS contexts requested for the function. */
+ uint16_t num_cmpl_rings;
+ /*
+ * The number of completion rings requested for the function.
+ * This does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_tx_rings;
+ /*
+ * The number of transmit rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_rx_rings;
+ /*
+ * The number of receive rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_l2_ctxs;
+ /* The requested number of L2 contexts for the function. */
+ uint16_t num_vnics;
+ /* The requested number of vnics for the function. */
+ uint16_t num_stat_ctxs;
+ /* The requested number of statistic contexts for the function. */
+ uint16_t num_hw_ring_grps;
+ /*
+ * The number of HW ring groups that should be reserved for this
+ * function.
+ */
+ uint8_t dflt_mac_addr[6];
+ /* The default MAC address for the function being configured. */
+ uint16_t dflt_vlan;
+ /*
+ * The default VLAN for the function being configured. This
+ * field's format is same as 802.1Q Tag's Tag Control
+ * Information (TCI) format that includes both Priority Code
+ * Point (PCP) and VLAN Identifier (VID).
+ */
+ uint32_t dflt_ip_addr[4];
+ /*
+ * The default IP address for the function being configured.
+ * This address is only used in enabling source property check.
+ */
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint16_t async_event_cr;
+ /*
+ * ID of the target completion ring for receiving asynchronous
+ * event completions. If this field is not valid, then the HWRM
+ * shall use the default completion ring of the function that is
+ * being configured as the target completion ring for providing
+ * any asynchronous event completions for that function. If this
+ * field is valid, then the HWRM shall use the completion ring
+ * identified by this ID as the target completion ring for
+ * providing any asynchronous event completions for the function
+ * that is being configured.
+ */
+ uint8_t vlan_antispoof_mode;
+ /* VLAN Anti-spoofing mode. */
+ /* No VLAN anti-spoofing checks are enabled */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_NOCHECK UINT32_C(0x0)
+ /* Validate VLAN against the configured VLAN(s) */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_VALIDATE_VLAN \
+ UINT32_C(0x1)
+ /* Insert VLAN if it does not exist, otherwise discard */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_IF_VLANDNE \
+ UINT32_C(0x2)
+ /*
+ * Insert VLAN if it does not exist, override
+ * VLAN if it exists
+ */
+ #define \
+ HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN \
+ UINT32_C(0x3)
+ uint8_t allowed_vlan_pris;
+ /*
+ * This bit field defines VLAN PRIs that are allowed on this
+ * function. If nth bit is set, then VLAN PRI n is allowed on
+ * this function.
+ */
+ uint8_t evb_mode;
+ /*
+ * The HWRM shall allow a PF driver to change EVB mode for the
+ * partition it belongs to. The HWRM shall not allow a VF driver
+ * to change the EVB mode. The HWRM shall take into account the
+ * switching of EVB mode from one to another and reconfigure
+ * hardware resources as appropriately. The switching from VEB
+ * to VEPA mode requires the disabling of the loopback traffic.
+ * Additionally, source knock outs are handled differently in
+ * VEB and VEPA modes.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEB UINT32_C(0x1)
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA UINT32_C(0x2)
+ uint8_t unused_2;
+ uint16_t num_mcast_filters;
+ /*
+ * The number of multicast filters that should be reserved for
+ * this function on the RX side.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qstats */
+/*
+ * Description: This command returns statistics of a function. The input FID
+ * value is used to indicate what function is being queried. This allows a
+ * physical function driver to query virtual functions that are children of the
+ * physical function. The HWRM shall return any unsupported counter with a value
+ * of 0xFFFFFFFF for 32-bit counters and 0xFFFFFFFFFFFFFFFF for 64-bit counters.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (176 bytes) */
+struct hwrm_func_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t tx_ucast_pkts;
+ /* Number of transmitted unicast packets on the function. */
+ uint64_t tx_mcast_pkts;
+ /* Number of transmitted multicast packets on the function. */
+ uint64_t tx_bcast_pkts;
+ /* Number of transmitted broadcast packets on the function. */
+ uint64_t tx_err_pkts;
+ /*
+ * Number of transmitted packets that were discarded due to
+ * internal NIC resource problems. For transmit, this can only
+ * happen if TMP is configured to allow dropping in HOL blocking
+ * conditions, which is not a normal configuration.
+ */
+ uint64_t tx_drop_pkts;
+ /*
+ * Number of dropped packets on transmit path on the function.
+ * These are packets that have been marked for drop by the TE
+ * CFA block or are packets that exceeded the transmit MTU limit
+ * for the function.
+ */
+ uint64_t tx_ucast_bytes;
+ /* Number of transmitted bytes for unicast traffic on the function. */
+ uint64_t tx_mcast_bytes;
+ /*
+ * Number of transmitted bytes for multicast traffic on the
+ * function.
+ */
+ uint64_t tx_bcast_bytes;
+ /*
+ * Number of transmitted bytes for broadcast traffic on the
+ * function.
+ */
+ uint64_t rx_ucast_pkts;
+ /* Number of received unicast packets on the function. */
+ uint64_t rx_mcast_pkts;
+ /* Number of received multicast packets on the function. */
+ uint64_t rx_bcast_pkts;
+ /* Number of received broadcast packets on the function. */
+ uint64_t rx_err_pkts;
+ /*
+ * Number of received packets that were discarded on the
+ * function due to resource limitations. This can happen for 3
+ * reasons. # The BD used for the packet has a bad format. #
+ * There were no BDs available in the ring for the packet. #
+ * There were no BDs available on-chip for the packet.
+ */
+ uint64_t rx_drop_pkts;
+ /*
+ * Number of dropped packets on received path on the function.
+ * These are packets that have been marked for drop by the RE
+ * CFA.
+ */
+ uint64_t rx_ucast_bytes;
+ /* Number of received bytes for unicast traffic on the function. */
+ uint64_t rx_mcast_bytes;
+ /* Number of received bytes for multicast traffic on the function. */
+ uint64_t rx_bcast_bytes;
+ /* Number of received bytes for broadcast traffic on the function. */
+ uint64_t rx_agg_pkts;
+ /* Number of aggregated unicast packets on the function. */
+ uint64_t rx_agg_bytes;
+ /* Number of aggregated unicast bytes on the function. */
+ uint64_t rx_agg_events;
+ /* Number of aggregation events on the function. */
+ uint64_t rx_agg_aborts;
+ /* Number of aborted aggregations on the function. */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_clr_stats */
+/*
+ * Description: This command clears statistics of a function. The input FID
+ * value is used to indicate what function's statistics is being cleared. This
+ * allows a physical function driver to clear statistics of virtual functions
+ * that are children of the physical function.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function. 0xFF... (All Fs) if the query is
+ * for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_vnic_ids_query */
+/* Description: This command is used to query vf vnic ids. */
+/* Input (32 bytes) */
+struct hwrm_func_vf_vnic_ids_query_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t max_vnic_id_cnt;
+ /* Max number of vnic ids in vnic id table */
+ uint64_t vnic_id_tbl_addr;
+ /* This is the address for VF VNIC ID table */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_vnic_ids_query_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t vnic_id_cnt;
+ /*
+ * Actual number of vnic ids Each VNIC ID is written as a 32-bit
+ * number.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_rgtr */
+/*
+ * Description: This command is used by the function driver to register its
+ * information with the HWRM. A function driver shall implement this command. A
+ * function driver shall use this command during the driver initialization right
+ * after the HWRM version discovery and default ring resources allocation.
+ */
+/* Input (80 bytes) */
+struct hwrm_func_drv_rgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function driver is requesting all
+ * requests from its children VF drivers to be forwarded to
+ * itself. This flag can only be set by the PF driver. If a VF
+ * driver sets this flag, it should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is requesting none of the
+ * requests from its children VF drivers to be forwarded to
+ * itself. This flag can only be set by the PF driver. If a VF
+ * driver sets this flag, it should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE UINT32_C(0x2)
+ uint32_t enables;
+ /* This bit must be '1' for the os_type field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE UINT32_C(0x1)
+ /* This bit must be '1' for the ver field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER UINT32_C(0x2)
+ /* This bit must be '1' for the timestamp field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP UINT32_C(0x4)
+ /* This bit must be '1' for the vf_req_fwd field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_INPUT_FWD UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the async_event_fwd field to be
+ * configured.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD UINT32_C(0x10)
+ uint16_t os_type;
+ /*
+ * This value indicates the type of OS. The values are based on
+ * CIM_OperatingSystem.mof file as published by the DMTF.
+ */
+ /* Unknown */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN UINT32_C(0x0)
+ /* Other OS not listed below. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER UINT32_C(0x1)
+ /* MSDOS OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS UINT32_C(0xe)
+ /* Windows OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS UINT32_C(0x12)
+ /* Solaris OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS UINT32_C(0x1d)
+ /* Linux OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX UINT32_C(0x24)
+ /* FreeBSD OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD UINT32_C(0x2a)
+ /* VMware ESXi OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI UINT32_C(0x68)
+ /* Microsoft Windows 8 64-bit OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864 UINT32_C(0x73)
+ /* Microsoft Windows Server 2012 R2 OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 UINT32_C(0x74)
+ uint8_t ver_maj;
+ /* This is the major version of the driver. */
+ uint8_t ver_min;
+ /* This is the minor version of the driver. */
+ uint8_t ver_upd;
+ /* This is the update version of the driver. */
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t timestamp;
+ /*
+ * This is a 32-bit timestamp provided by the driver for keep
+ * alive. The timestamp is in multiples of 1ms.
+ */
+ uint32_t unused_2;
+ uint32_t vf_req_fwd[8];
+ /*
+ * This is a 256-bit bit mask provided by the PF driver for
+ * letting the HWRM know what commands issued by the VF driver
+ * to the HWRM should be forwarded to the PF driver. Nth bit
+ * refers to the Nth req_type. Setting Nth bit to 1 indicates
+ * that requests from the VF driver with req_type equal to N
+ * shall be forwarded to the parent PF driver. This field is not
+ * valid for the VF driver.
+ */
+ uint32_t async_event_fwd[8];
+ /*
+ * This is a 256-bit bit mask provided by the function driver
+ * (PF or VF driver) to indicate the list of asynchronous event
+ * completions to be forwarded. Nth bit refers to the Nth
+ * event_id. Setting Nth bit to 1 by the function driver shall
+ * result in the HWRM forwarding asynchronous event completion
+ * with event_id equal to N. If all bits are set to 0 (value of
+ * 0), then the HWRM shall not forward any asynchronous event
+ * completion to this function driver.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_rgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_unrgtr */
+/*
+ * Description: This command is used by the function driver to un register with
+ * the HWRM. A function driver shall implement this command. A function driver
+ * shall use this command during the driver unloading.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_drv_unrgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function driver is notifying the
+ * HWRM to prepare for the shutdown.
+ */
+ #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN \
+ UINT32_C(0x1)
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_unrgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_buf_rgtr */
+/*
+ * Description: This command is used by the PF driver to register buffers used
+ * in the PF-VF communication with the HWRM. The PF driver uses this command to
+ * register buffers for each PF-VF channel. A parent PF may issue this command
+ * per child VF. If VF ID is not valid, then this command is used to register
+ * buffers for all children VFs of the PF.
+ */
+/* Input (128 bytes) */
+struct hwrm_func_buf_rgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id field to be configured. */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_VF_ID UINT32_C(0x1)
+ /* This bit must be '1' for the err_buf_addr field to be configured. */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_ERR_BUF_ADDR UINT32_C(0x2)
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t req_buf_num_pages;
+ /*
+ * This field represents the number of pages used for request
+ * buffer(s).
+ */
+ uint16_t req_buf_page_size;
+ /* This field represents the page size used for request buffer(s). */
+ /* 16 bytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_16B UINT32_C(0x4)
+ /* 4 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4K UINT32_C(0xc)
+ /* 8 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_8K UINT32_C(0xd)
+ /* 64 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_64K UINT32_C(0x10)
+ /* 2 Mbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_2M UINT32_C(0x15)
+ /* 4 Mbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4M UINT32_C(0x16)
+ /* 1 Gbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_1G UINT32_C(0x1e)
+ uint16_t req_buf_len;
+ /* The length of the request buffer per VF in bytes. */
+ uint16_t resp_buf_len;
+ /* The length of the response buffer in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint64_t req_buf_page_addr[10];
+ /* This field represents the page address of req buffer. */
+ uint64_t error_buf_addr;
+ /*
+ * This field is used to receive the error reporting from the
+ * chipset. Only applicable for PFs.
+ */
+ uint64_t resp_buf_addr;
+ /* This field is used to receive the response forwarded by the HWRM. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_buf_rgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_buf_unrgtr */
+/*
+ * Description: This command is used by the PF driver to unregister buffers used
+ * in the PF-VF communication with the HWRM. The PF driver uses this command to
+ * unregister buffers for PF-VF communication. A parent PF may issue this
+ * command to unregister buffers for communication between the PF and a specific
+ * VF. If the VF ID is not valid, then this command is used to unregister
+ * buffers used for communications with all children VFs of the PF.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_buf_unrgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id field to be configured. */
+ #define HWRM_FUNC_BUF_UNRGTR_INPUT_ENABLES_VF_ID UINT32_C(0x1)
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_buf_unrgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_cfg */
+/*
+ * Description: This command allows configuration of a VF by its driver. If this
+ * function is called by a PF driver, then the HWRM shall fail this command. If
+ * guest VLAN and/or MAC address are provided in this command, then the HWRM
+ * shall set up appropriate MAC/VLAN filters for the VF that is being
+ * configured. A VF driver should set VF MTU/MRU using this command prior to
+ * allocating RX VNICs or TX rings for the corresponding VF.
+ */
+/* Input (32 bytes) */
+
+struct hwrm_func_vf_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the mtu field to be configured. */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
+ /* This bit must be '1' for the guest_vlan field to be configured. */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_GUEST_VLAN UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the async_event_cr field to be configured.
+ */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_ASYNC_EVENT_CR UINT32_C(0x4)
+ /* This bit must be '1' for the dflt_mac_addr field to be configured. */
+ #define HWRM_FUNC_VF_CFG_INPUT_ENABLES_DFLT_MAC_ADDR UINT32_C(0x8)
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit requested on the function. The HWRM
+ * should make sure that the mtu of the function does not exceed the mtu
+ * of the physical port that this function is associated with. In
+ * addition to requesting mtu per function, it is possible to configure
+ * mtu per transmit ring. By default, the mtu of each transmit ring
+ * associated with a function is equal to the mtu of the function. The
+ * HWRM should make sure that the mtu of each transmit ring that is
+ * assigned to a function has a valid mtu.
+ */
+ uint16_t guest_vlan;
+ /*
+ * The guest VLAN for the function being configured. This field's format
+ * is same as 802.1Q Tag's Tag Control Information (TCI) format that
+ * includes both Priority Code Point (PCP) and VLAN Identifier (VID).
+ */
+ uint16_t async_event_cr;
+ /*
+ * ID of the target completion ring for receiving asynchronous event
+ * completions. If this field is not valid, then the HWRM shall use the
+ * default completion ring of the function that is being configured as
+ * the target completion ring for providing any asynchronous event
+ * completions for that function. If this field is valid, then the HWRM
+ * shall use the completion ring identified by this ID as the target
+ * completion ring for providing any asynchronous event completions for
+ * the function that is being configured.
+ */
+ uint8_t dflt_mac_addr[6];
+ /*
+ * This value is the current MAC address requested by the VF driver to
+ * be configured on this VF. A value of 00-00-00-00-00-00 indicates no
+ * MAC address configuration is requested by the VF driver. The parent
+ * PF driver may reject or overwrite this MAC address.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+
+struct hwrm_func_vf_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_cfg */
+/*
+ * Description: This command configures the PHY device for the port. It allows
+ * setting of the most generic settings for the PHY. The HWRM shall complete
+ * this command as soon as PHY settings are configured. They may not be applied
+ * when the command response is provided. A VF driver shall not be allowed to
+ * configure PHY using this command. In a network partition mode, a PF driver
+ * shall not be allowed to configure PHY using this command.
+ */
+/* Input (56 bytes) */
+struct hwrm_port_phy_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is set to '1', the PHY for the port shall be
+ * reset. # If this bit is set to 1, then the HWRM shall reset
+ * the PHY after applying PHY configuration changes specified in
+ * this command. # In order to guarantee that PHY configuration
+ * changes specified in this command take effect, the HWRM
+ * client should set this flag to 1. # If this bit is not set to
+ * 1, then the HWRM may reset the PHY depending on the current
+ * PHY configuration and settings specified in this command.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY UINT32_C(0x1)
+ /* deprecated bit. Do not use!!! */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_DEPRECATED UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', the link shall be forced to the
+ * force_link_speed value. When this bit is set to '1', the HWRM
+ * client should not enable any of the auto negotiation related
+ * fields represented by auto_XXX fields in this command. When
+ * this bit is set to '1' and the HWRM client has enabled a
+ * auto_XXX field in this command, then the HWRM shall ignore
+ * the enabled auto_XXX field. When this bit is set to zero, the
+ * link shall be allowed to autoneg.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', the auto-negotiation process
+ * shall be restarted on the link.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE)
+ * is requested to be enabled on this link. If EEE is not
+ * supported on this port, then this flag shall be ignored by
+ * the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE)
+ * is requested to be disabled on this link. If EEE is not
+ * supported on this port, then this flag shall be ignored by
+ * the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE UINT32_C(0x20)
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link,
+ * then TX LPI is requested to be enabled on the link. If EEE is
+ * not supported on this port, then this flag shall be ignored
+ * by the HWRM. If EEE is disabled on this port, then this flag
+ * shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_ENABLE UINT32_C(0x40)
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link,
+ * then TX LPI is requested to be disabled on the link. If EEE
+ * is not supported on this port, then this flag shall be
+ * ignored by the HWRM. If EEE is disabled on this port, then
+ * this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_DISABLE UINT32_C(0x80)
+ /*
+ * When set to 1, then the HWRM shall enable FEC
+ * autonegotitation on this port if supported. When set to 0,
+ * then this flag shall be ignored. If FEC autonegotiation is
+ * not supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_ENABLE UINT32_C(0x100)
+ /*
+ * When set to 1, then the HWRM shall disable FEC
+ * autonegotiation on this port if supported. When set to 0,
+ * then this flag shall be ignored. If FEC autonegotiation is
+ * not supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_DISABLE \
+ UINT32_C(0x200)
+ /*
+ * When set to 1, then the HWRM shall enable FEC CLAUSE 74 (Fire
+ * Code) on this port if supported. When set to 0, then this
+ * flag shall be ignored. If FEC CLAUSE 74 is not supported,
+ * then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_ENABLE \
+ UINT32_C(0x400)
+ /*
+ * When set to 1, then the HWRM shall disable FEC CLAUSE 74
+ * (Fire Code) on this port if supported. When set to 0, then
+ * this flag shall be ignored. If FEC CLAUSE 74 is not
+ * supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_DISABLE \
+ UINT32_C(0x800)
+ /*
+ * When set to 1, then the HWRM shall enable FEC CLAUSE 91 (Reed
+ * Solomon) on this port if supported. When set to 0, then this
+ * flag shall be ignored. If FEC CLAUSE 91 is not supported,
+ * then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_ENABLE \
+ UINT32_C(0x1000)
+ /*
+ * When set to 1, then the HWRM shall disable FEC CLAUSE 91
+ * (Reed Solomon) on this port if supported. When set to 0, then
+ * this flag shall be ignored. If FEC CLAUSE 91 is not
+ * supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_DISABLE \
+ UINT32_C(0x2000)
+ /*
+ * When this bit is set to '1', the link shall be forced to be
+ * taken down. # When this bit is set to '1", all other command
+ * input settings related to the link speed shall be ignored.
+ * Once the link state is forced down, it can be explicitly
+ * cleared from that state by setting this flag to '0'. # If
+ * this flag is set to '0', then the link shall be cleared from
+ * forced down state if the link is in forced down state. There
+ * may be conditions (e.g. out-of-band or sideband configuration
+ * changes for the link) outside the scope of the HWRM
+ * implementation that may clear forced down link state.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DWN UINT32_C(0x4000)
+ uint32_t enables;
+ /* This bit must be '1' for the auto_mode field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE UINT32_C(0x1)
+ /* This bit must be '1' for the auto_duplex field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX UINT32_C(0x2)
+ /* This bit must be '1' for the auto_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the auto_link_speed field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the auto_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the wirespeed field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIOUTPUTEED UINT32_C(0x20)
+ /* This bit must be '1' for the lpbk field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK UINT32_C(0x40)
+ /* This bit must be '1' for the preemphasis field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS UINT32_C(0x80)
+ /* This bit must be '1' for the force_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the eee_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the tx_lpi_timer field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER UINT32_C(0x400)
+ uint16_t port_id;
+ /* Port ID of port that is to be configured. */
+ uint16_t force_link_speed;
+ /*
+ * This is the speed that will be used if the force bit is '1'.
+ * If unsupported speed is selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint8_t auto_mode;
+ /*
+ * This value is used to identify what autoneg mode is used when
+ * the link speed is not being forced.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK UINT32_C(0x4)
+ uint8_t auto_duplex;
+ /*
+ * This is the duplex setting that will be used if the
+ * autoneg_mode is "one_speed" or "one_or_below".
+ */
+ /* Half Duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF UINT32_C(0x0)
+ /* Full duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL UINT32_C(0x1)
+ /* Both Half and Full dupex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH UINT32_C(0x2)
+ uint8_t auto_pause;
+ /*
+ * This value is used to configure the pause that will be used
+ * for autonegotiation. Add text on the usage of auto_pause and
+ * force_pause.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has
+ * been requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When
+ * the auto_mode is not set to none and this flag is set to 1,
+ * then the auto_pause bits on this port are being advertised
+ * and autoneg pause results are being interpreted. # When the
+ * auto_mode is not set to none and this flag is set to 0, the
+ * pause is forced as indicated in force_pause, and also
+ * advertised as auto_pause bits, but the autoneg results are
+ * not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is
+ * set to 1, auto_pause bits should be ignored and should be set
+ * to 0.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
+ uint8_t unused_0;
+ uint16_t auto_link_speed;
+ /*
+ * This is the speed that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below". If an unsupported speed is
+ * selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint16_t auto_link_speed_mask;
+ /*
+ * This is a mask of link speeds that will be used if
+ * autoneg_mode is "mask". If unsupported speed is enabled an
+ * error will be generated.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint8_t wirespeed;
+ /* This value controls the wirespeed feature. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_OFF UINT32_C(0x0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_ON UINT32_C(0x1)
+ uint8_t lpbk;
+ /* This value controls the loopback setting for the PHY. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE UINT32_C(0x2)
+ uint8_t force_pause;
+ /*
+ * This value is used to configure the pause that will be used
+ * for force mode.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX UINT32_C(0x2)
+ uint8_t unused_1;
+ uint32_t preemphasis;
+ /*
+ * This value controls the pre-emphasis to be used for the link.
+ * Driver should not set this value (use enable.preemphasis = 0)
+ * unless driver is sure of setting. Normally HWRM FW will
+ * determine proper pre-emphasis.
+ */
+ uint16_t eee_link_speed_mask;
+ /*
+ * Setting for link speed mask that is used to advertise speeds
+ * during autonegotiation when EEE is enabled. This field is
+ * valid only when EEE is enabled. The speeds specified in this
+ * field shall be a subset of speeds specified in
+ * auto_link_speed_mask. If EEE is enabled,then at least one
+ * speed shall be provided in this mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB UINT32_C(0x40)
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t tx_lpi_timer;
+ uint32_t unused_4;
+ /*
+ * Reuested setting of TX LPI timer in microseconds. This field
+ * is valid only when EEE is enabled and TX LPI is enabled.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_phy_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_qcfg */
+/* Description: This command queries the PHY configuration for the port. */
+/* Input (24 bytes) */
+struct hwrm_port_phy_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is to be queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (96 bytes) */
+struct hwrm_port_phy_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t link;
+ /* This value indicates the current link status. */
+ /* There is no link or cable detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK UINT32_C(0x0)
+ /* There is no link, but a cable has been detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL UINT32_C(0x1)
+ /* There is a link. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK UINT32_C(0x2)
+ uint8_t unused_0;
+ uint16_t link_speed;
+ /* This value indicates the current link speed of the connection. */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint8_t duplex;
+ /* This value is indicates the duplex of the current connection. */
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_HALF UINT32_C(0x0)
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_FULL UINT32_C(0x1)
+ uint8_t pause;
+ /*
+ * This value is used to indicate the current pause
+ * configuration. When autoneg is enabled, this value represents
+ * the autoneg results of pause configuration.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX UINT32_C(0x2)
+ uint16_t support_speeds;
+ /*
+ * The supported speeds for the port. This is a bit mask. For
+ * each speed that is supported, the corrresponding bit will be
+ * set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB UINT32_C(0x2000)
+ uint16_t force_link_speed;
+ /*
+ * Current setting of forced link speed. When the link speed is
+ * not being forced, this value shall be set to 0.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint8_t auto_mode;
+ /* Current setting of auto negotiation mode. */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK UINT32_C(0x4)
+ uint8_t auto_pause;
+ /*
+ * Current setting of pause autonegotiation. Move autoneg_pause
+ * flag here.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has
+ * been requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When
+ * the auto_mode is not set to none and this flag is set to 1,
+ * then the auto_pause bits on this port are being advertised
+ * and autoneg pause results are being interpreted. # When the
+ * auto_mode is not set to none and this flag is set to 0, the
+ * pause is forced as indicated in force_pause, and also
+ * advertised as auto_pause bits, but the autoneg results are
+ * not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is
+ * set to 1, auto_pause bits should be ignored and should be set
+ * to 0.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
+ uint16_t auto_link_speed;
+ /*
+ * Current setting for auto_link_speed. This field is only valid
+ * when auto_mode is set to "one_speed" or "one_or_below".
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint16_t auto_link_speed_mask;
+ /*
+ * Current setting for auto_link_speed_mask that is used to
+ * advertise speeds during autonegotiation. This field is only
+ * valid when auto_mode is set to "mask". The speeds specified
+ * in this field shall be a subset of supported speeds on this
+ * port.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint8_t wirespeed;
+ /* Current setting for wirespeed. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_OFF UINT32_C(0x0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_ON UINT32_C(0x1)
+ uint8_t lpbk;
+ /* Current setting for loopback. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
+ uint8_t force_pause;
+ /*
+ * Current setting of forced pause. When the pause configuration
+ * is not being forced, then this value shall be set to 0.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX UINT32_C(0x2)
+ uint8_t module_status;
+ /*
+ * This value indicates the current status of the optics module
+ * on this port.
+ */
+ /* Module is inserted and accepted */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE UINT32_C(0x0)
+ /* Module is rejected and transmit side Laser is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX UINT32_C(0x1)
+ /* Module mismatch warning. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG UINT32_C(0x2)
+ /* Module is rejected and powered down. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN UINT32_C(0x3)
+ /* Module is not inserted. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED \
+ UINT32_C(0x4)
+ /* Module status is not applicable. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE \
+ UINT32_C(0xff)
+ uint32_t preemphasis;
+ /* Current setting for preemphasis. */
+ uint8_t phy_maj;
+ /* This field represents the major version of the PHY. */
+ uint8_t phy_min;
+ /* This field represents the minor version of the PHY. */
+ uint8_t phy_bld;
+ /* This field represents the build version of the PHY. */
+ uint8_t phy_type;
+ /* This value represents a PHY type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN UINT32_C(0x0)
+ /* BASE-CR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR UINT32_C(0x1)
+ /* BASE-KR4 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 UINT32_C(0x2)
+ /* BASE-LR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR UINT32_C(0x3)
+ /* BASE-SR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR UINT32_C(0x4)
+ /* BASE-KR2 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 UINT32_C(0x5)
+ /* BASE-KX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX UINT32_C(0x6)
+ /* BASE-KR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR UINT32_C(0x7)
+ /* BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET UINT32_C(0x8)
+ /* EEE capable BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE UINT32_C(0x9)
+ /* SGMII connected external PHY */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY UINT32_C(0xa)
+ /* 25G_BASECR_CA_L */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_L UINT32_C(0xb)
+ /* 25G_BASECR_CA_S */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_S UINT32_C(0xc)
+ /* 25G_BASECR_CA_N */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_N UINT32_C(0xd)
+ /* 25G_BASESR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASESR UINT32_C(0xe)
+ /* 100G_BASECR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASECR4 UINT32_C(0xf)
+ /* 100G_BASESR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR4 UINT32_C(0x10)
+ /* 100G_BASELR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASELR4 UINT32_C(0x11)
+ /* 100G_BASEER4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASEER4 UINT32_C(0x12)
+ /* 100G_BASESR10 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR10 UINT32_C(0x13)
+ /* 40G_BASECR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASECR4 UINT32_C(0x14)
+ /* 40G_BASESR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASESR4 UINT32_C(0x15)
+ /* 40G_BASELR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASELR4 UINT32_C(0x16)
+ /* 40G_BASEER4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASEER4 UINT32_C(0x17)
+ /* 40G_ACTIVE_CABLE */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_ACTIVE_CABLE \
+ UINT32_C(0x18)
+ uint8_t media_type;
+ /* This value represents a media type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN UINT32_C(0x0)
+ /* Twisted Pair */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP UINT32_C(0x1)
+ /* Direct Attached Copper */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC UINT32_C(0x2)
+ /* Fiber */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE UINT32_C(0x3)
+ uint8_t xcvr_pkg_type;
+ /* This value represents a transceiver type. */
+ /* PHY and MAC are in the same package */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL \
+ UINT32_C(0x1)
+ /* PHY and MAC are in different packages */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL \
+ UINT32_C(0x2)
+ uint8_t eee_config_phy_addr;
+ /*
+ * This field represents flags related to EEE configuration.
+ * These EEE configuration flags are valid only when the
+ * auto_mode is not set to none (in other words autonegotiation
+ * is enabled).
+ */
+ /* This field represents PHY address. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK UINT32_C(0x1f)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT 0
+ /*
+ * When set to 1, Energy Efficient Ethernet (EEE) mode is
+ * enabled. Speeds for autoneg with EEE mode enabled are based
+ * on eee_link_speed_mask.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED UINT32_C(0x20)
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this
+ * flag shall be ignored. # If eee_enabled is set to 1 and this
+ * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
+ * is enabled and in use. # If eee_enabled is set to 1 and this
+ * flag is set to 0, then Energy Efficient Ethernet (EEE) mode
+ * is enabled but is currently not in use.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE UINT32_C(0x40)
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this
+ * flag shall be ignored. # If eee_enabled is set to 1 and this
+ * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
+ * is enabled and TX LPI is enabled. # If eee_enabled is set to
+ * 1 and this flag is set to 0, then Energy Efficient Ethernet
+ * (EEE) mode is enabled but TX LPI is disabled.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI UINT32_C(0x80)
+ /*
+ * This field represents flags related to EEE configuration.
+ * These EEE configuration flags are valid only when the
+ * auto_mode is not set to none (in other words autonegotiation
+ * is enabled).
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK UINT32_C(0xe0)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT 5
+ uint8_t parallel_detect;
+ /* Reserved field, set to 0 */
+ /*
+ * When set to 1, the parallel detection is used to determine
+ * the speed of the link partner. Parallel detection is used
+ * when a autonegotiation capable device is connected to a link
+ * parter that is not capable of autonegotiation.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT UINT32_C(0x1)
+ /* Reserved field, set to 0 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK UINT32_C(0xfe)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1
+ uint16_t link_partner_adv_speeds;
+ /*
+ * The advertised speeds for the port by the link partner. Each
+ * advertised speed will be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \
+ UINT32_C(0x2000)
+ uint8_t link_partner_adv_auto_mode;
+ /*
+ * The advertised autoneg for the port by the link partner. This
+ * field is deprecated and should be set to 0.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \
+ UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
+ UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
+ UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
+ UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
+ UINT32_C(0x4)
+ uint8_t link_partner_adv_pause;
+ /* The advertised pause settings on the port by the link partner. */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
+ UINT32_C(0x2)
+ uint16_t adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is used to advertise
+ * speeds during autonegotiation when EEE is enabled. This field
+ * is valid only when eee_enabled flags is set to 1. The speeds
+ * specified in this field shall be a subset of speeds specified
+ * in auto_link_speed_mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t link_partner_adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is advertised by the
+ * link partner when EEE is enabled. This field is valid only
+ * when eee_enabled flags is set to 1.
+ */
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint32_t xcvr_identifier_type_tx_lpi_timer;
+ /* This value represents transceiver identifier type. */
+ /*
+ * Current setting of TX LPI timer in microseconds. This field
+ * is valid only when_eee_enabled flag is set to 1 and
+ * tx_lpi_enabled is set to 1.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
+ /* This value represents transceiver identifier type. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT 24
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 24)
+ /* SFP/SFP+/SFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
+ (UINT32_C(0x3) << 24)
+ /* QSFP */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
+ (UINT32_C(0xc) << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
+ (UINT32_C(0xd) << 24)
+ /* QSFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
+ (UINT32_C(0x11) << 24)
+ uint16_t fec_cfg;
+ /*
+ * This value represents the current configuration of Forward
+ * Error Correction (FEC) on the port.
+ */
+ /*
+ * When set to 1, then FEC is not supported on this port. If
+ * this flag is set to 1, then all other FEC configuration flags
+ * shall be ignored. When set to 0, then FEC is supported as
+ * indicated by other configuration flags. If no cable is
+ * attached and the HWRM does not yet know the FEC capability,
+ * then the HWRM shall set this flag to 1 when reporting FEC
+ * capability.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * When set to 1, then FEC autonegotiation is supported on this
+ * port. When set to 0, then FEC autonegotiation is not
+ * supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * When set to 1, then FEC autonegotiation is enabled on this
+ * port. When set to 0, then FEC autonegotiation is disabled if
+ * supported. This flag should be ignored if FEC autonegotiation
+ * is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED \
+ UINT32_C(0x4)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * disabled if supported. This flag should be ignored if FEC
+ * CLAUSE 74 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED \
+ UINT32_C(0x10)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is supported
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is enabled
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is disabled if supported. This flag should be
+ * ignored if FEC CLAUSE 91 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED \
+ UINT32_C(0x40)
+ uint8_t unused_1;
+ uint8_t unused_2;
+ char phy_vendor_name[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string representing PHY
+ * vendor. If the string is set to null, then the vendor name is
+ * not available.
+ */
+ char phy_vendor_partnumber[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string that identifies
+ * vendor specific part number of the PHY. If the string is set
+ * to null, then the vendor specific part number is not
+ * available.
+ */
+ uint32_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t unused_6;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_qstats */
+/* Description: This function returns per port Ethernet statistics. */
+/* Input (40 bytes) */
+struct hwrm_port_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2[3];
+ uint8_t unused_3;
+ uint64_t tx_stat_host_addr;
+ /* This is the host address where Tx port statistics will be stored */
+ uint64_t rx_stat_host_addr;
+ /* This is the host address where Rx port statistics will be stored */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t tx_stat_size;
+ /* The size of TX port statistics block in bytes. */
+ uint16_t rx_stat_size;
+ /* The size of RX port statistics block in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_clr_stats */
+/*
+ * Description: This function clears per port statistics. The HWRM shall not
+ * allow a VF driver to clear port statistics. The HWRM shall not allow a PF
+ * driver to clear port statistics in a partitioning mode. The HWRM may allow a
+ * PF driver to clear port statistics in the non-partitioning mode.