+ /* Lossless RoCE */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS_ROCE \
+ UINT32_C(0x1)
+ /* Lossy RoCE CNP */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY_ROCE_CNP \
+ UINT32_C(0x2)
+ /* Lossless NIC */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS_NIC \
+ UINT32_C(0x3)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN
+ /*
+ * ID of CoS Queue 4.
+ * FF - Invalid id
+ *
+ * # This ID can be used on any subsequent call to an hwrm command
+ * that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software.
+ * # The CoS queue index is obtained by applying modulo 10 to the
+ * CoS queue ID. Valid CoS queue indexes are in the range of 0 to 7.
+ * The CoS queue index is used to reference port statistics for the
+ * CoS queue.
+ * # A value of 0xff indicates that the queue is not available.
+ * # Available queues may not be in sequential order.
+ */
+ uint8_t queue_id4;
+ /* This value is applicable to CoS queues only. */
+ uint8_t queue_id4_service_profile;
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless (legacy) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /* Lossless RoCE */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS_ROCE \
+ UINT32_C(0x1)
+ /* Lossy RoCE CNP */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY_ROCE_CNP \
+ UINT32_C(0x2)
+ /* Lossless NIC */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS_NIC \
+ UINT32_C(0x3)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN
+ /*
+ * ID of CoS Queue 5.
+ * FF - Invalid id
+ *
+ * # This ID can be used on any subsequent call to an hwrm command
+ * that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software.
+ * # The CoS queue index is obtained by applying modulo 10 to the
+ * CoS queue ID. Valid CoS queue indexes are in the range of 0 to 7.
+ * The CoS queue index is used to reference port statistics for the
+ * CoS queue.
+ * # A value of 0xff indicates that the queue is not available.
+ * # Available queues may not be in sequential order.
+ */
+ uint8_t queue_id5;
+ /* This value is applicable to CoS queues only. */
+ uint8_t queue_id5_service_profile;
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless (legacy) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /* Lossless RoCE */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS_ROCE \
+ UINT32_C(0x1)
+ /* Lossy RoCE CNP */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY_ROCE_CNP \
+ UINT32_C(0x2)
+ /* Lossless NIC */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS_NIC \
+ UINT32_C(0x3)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN
+ /*
+ * ID of CoS Queue 6.
+ * FF - Invalid id
+ *
+ * # This ID can be used on any subsequent call to an hwrm command
+ * that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software.
+ * # The CoS queue index is obtained by applying modulo 10 to the
+ * CoS queue ID. Valid CoS queue indexes are in the range of 0 to 7.
+ * The CoS queue index is used to reference port statistics for the
+ * CoS queue.
+ * # A value of 0xff indicates that the queue is not available.
+ * # Available queues may not be in sequential order.
+ */
+ uint8_t queue_id6;
+ /* This value is applicable to CoS queues only. */
+ uint8_t queue_id6_service_profile;
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless (legacy) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /* Lossless RoCE */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS_ROCE \
+ UINT32_C(0x1)
+ /* Lossy RoCE CNP */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY_ROCE_CNP \
+ UINT32_C(0x2)
+ /* Lossless NIC */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS_NIC \
+ UINT32_C(0x3)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN
+ /*
+ * ID of CoS Queue 7.
+ * FF - Invalid id
+ *
+ * # This ID can be used on any subsequent call to an hwrm command
+ * that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software.
+ * # The CoS queue index is obtained by applying modulo 10 to the
+ * CoS queue ID. Valid CoS queue indexes are in the range of 0 to 7.
+ * The CoS queue index is used to reference port statistics for the
+ * CoS queue.
+ * # A value of 0xff indicates that the queue is not available.
+ * # Available queues may not be in sequential order.
+ */
+ uint8_t queue_id7;
+ /* This value is applicable to CoS queues only. */
+ uint8_t queue_id7_service_profile;
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless (legacy) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /* Lossless RoCE */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS_ROCE \
+ UINT32_C(0x1)
+ /* Lossy RoCE CNP */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY_ROCE_CNP \
+ UINT32_C(0x2)
+ /* Lossless NIC */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS_NIC \
+ UINT32_C(0x3)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN
+ uint8_t unused_0;
+ /*
+ * Up to 16 bytes of null padded ASCII string describing this queue.
+ * The queue name includes a CoS queue index and, in some cases, text
+ * that distinguishes the queue from other queues in the group.
+ */
+ char qid0_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid1_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid2_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid3_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid4_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid5_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid6_name[16];
+ /* Up to 16 bytes of null padded ASCII string describing this queue. */
+ char qid7_name[16];
+ uint8_t unused_1[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************
+ * hwrm_queue_qcfg *
+ *******************/
+
+
+/* hwrm_queue_qcfg_input (size:192b/24B) */
+struct hwrm_queue_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_QCFG_INPUT_FLAGS_PATH_RX
+ /* Queue ID of the queue. */
+ uint32_t queue_id;
+} __rte_packed;
+
+/* hwrm_queue_qcfg_output (size:128b/16B) */
+struct hwrm_queue_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * This value is the estimate packet length used in the
+ * TX arbiter.
+ */
+ uint32_t queue_len;
+ /* This value is applicable to CoS queues only. */
+ uint8_t service_profile;
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LOSSY UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LOSSLESS UINT32_C(0x1)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_UNKNOWN UINT32_C(0xff)
+ #define HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_QCFG_OUTPUT_SERVICE_PROFILE_UNKNOWN
+ /* Information about queue configuration. */
+ uint8_t queue_cfg_info;
+ /*
+ * If this flag is set to '1', then the queue is
+ * configured asymmetrically on TX and RX sides.
+ * If this flag is set to '0', then this queue is
+ * configured symmetrically on TX and RX sides.
+ */
+ #define HWRM_QUEUE_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG \
+ UINT32_C(0x1)
+ uint8_t unused_0;
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************
+ * hwrm_queue_cfg *
+ ******************/
+
+
+/* hwrm_queue_cfg_input (size:320b/40B) */
+struct hwrm_queue_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX, or both directions applicable to the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_MASK UINT32_C(0x3)
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_SFT 0
+ /* tx path */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ /* Bi-directional (Symmetrically applicable to TX and RX paths) */
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_BIDIR UINT32_C(0x2)
+ #define HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_CFG_INPUT_FLAGS_PATH_BIDIR
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the dflt_len field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_CFG_INPUT_ENABLES_DFLT_LEN UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the service_profile field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_CFG_INPUT_ENABLES_SERVICE_PROFILE UINT32_C(0x2)
+ /* Queue ID of queue that is to be configured by this function. */
+ uint32_t queue_id;
+ /*
+ * This value is a the estimate packet length used in the
+ * TX arbiter.
+ * Set to 0xFF... (All Fs) to not adjust this value.
+ */
+ uint32_t dflt_len;
+ /* This value is applicable to CoS queues only. */
+ uint8_t service_profile;
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LOSSY UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LOSSLESS UINT32_C(0x1)
+ /* Set to 0xFF... (All Fs) if there is no service profile specified */
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_UNKNOWN UINT32_C(0xff)
+ #define HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_LAST \
+ HWRM_QUEUE_CFG_INPUT_SERVICE_PROFILE_UNKNOWN
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_queue_cfg_output (size:128b/16B) */
+struct hwrm_queue_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*****************************
+ * hwrm_queue_pfcenable_qcfg *
+ *****************************/
+
+
+/* hwrm_queue_pfcenable_qcfg_input (size:192b/24B) */
+struct hwrm_queue_pfcenable_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_queue_pfcenable_qcfg_output (size:128b/16B) */
+struct hwrm_queue_pfcenable_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t flags;
+ /* If set to 1, then PFC is enabled on PRI 0. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI0_PFC_ENABLED \
+ UINT32_C(0x1)
+ /* If set to 1, then PFC is enabled on PRI 1. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI1_PFC_ENABLED \
+ UINT32_C(0x2)
+ /* If set to 1, then PFC is enabled on PRI 2. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI2_PFC_ENABLED \
+ UINT32_C(0x4)
+ /* If set to 1, then PFC is enabled on PRI 3. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI3_PFC_ENABLED \
+ UINT32_C(0x8)
+ /* If set to 1, then PFC is enabled on PRI 4. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI4_PFC_ENABLED \
+ UINT32_C(0x10)
+ /* If set to 1, then PFC is enabled on PRI 5. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI5_PFC_ENABLED \
+ UINT32_C(0x20)
+ /* If set to 1, then PFC is enabled on PRI 6. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI6_PFC_ENABLED \
+ UINT32_C(0x40)
+ /* If set to 1, then PFC is enabled on PRI 7. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI7_PFC_ENABLED \
+ UINT32_C(0x80)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI0. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI0_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x100)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI1. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI1_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x200)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI2. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI2_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x400)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI3. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI3_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x800)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI4. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI4_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x1000)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI5. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI5_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x2000)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI6. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI6_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x4000)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI7. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI7_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x8000)
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/****************************
+ * hwrm_queue_pfcenable_cfg *
+ ****************************/
+
+
+/* hwrm_queue_pfcenable_cfg_input (size:192b/24B) */
+struct hwrm_queue_pfcenable_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* If set to 1, then PFC is requested to be enabled on PRI 0. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI0_PFC_ENABLED \
+ UINT32_C(0x1)
+ /* If set to 1, then PFC is requested to be enabled on PRI 1. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI1_PFC_ENABLED \
+ UINT32_C(0x2)
+ /* If set to 1, then PFC is requested to be enabled on PRI 2. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI2_PFC_ENABLED \
+ UINT32_C(0x4)
+ /* If set to 1, then PFC is requested to be enabled on PRI 3. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI3_PFC_ENABLED \
+ UINT32_C(0x8)
+ /* If set to 1, then PFC is requested to be enabled on PRI 4. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI4_PFC_ENABLED \
+ UINT32_C(0x10)
+ /* If set to 1, then PFC is requested to be enabled on PRI 5. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI5_PFC_ENABLED \
+ UINT32_C(0x20)
+ /* If set to 1, then PFC is requested to be enabled on PRI 6. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI6_PFC_ENABLED \
+ UINT32_C(0x40)
+ /* If set to 1, then PFC is requested to be enabled on PRI 7. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI7_PFC_ENABLED \
+ UINT32_C(0x80)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI0. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI0_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x100)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI1. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI1_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x200)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI2. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI2_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x400)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI3. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI3_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x800)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI4. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI4_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x1000)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI5. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI5_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x2000)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI6. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI6_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x4000)
+ /* If set to 1, then PFC WatchDog is requested to be enabled on PRI7. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI7_PFC_WATCHDOG_ENABLED \
+ UINT32_C(0x8000)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint16_t port_id;
+ uint8_t unused_0[2];
+} __rte_packed;
+
+/* hwrm_queue_pfcenable_cfg_output (size:128b/16B) */
+struct hwrm_queue_pfcenable_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_queue_pri2cos_qcfg *
+ ***************************/
+
+
+/* hwrm_queue_pri2cos_qcfg_input (size:192b/24B) */
+struct hwrm_queue_pri2cos_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX
+ /*
+ * When this bit is set to '0', the query is
+ * for PRI from tunnel headers.
+ * When this bit is set to '1', the query is
+ * for PRI from inner packet headers.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_IVLAN UINT32_C(0x2)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0[3];
+} __rte_packed;
+
+/* hwrm_queue_pri2cos_qcfg_output (size:192b/24B) */
+struct hwrm_queue_pri2cos_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * CoS Queue assigned to priority 0. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri0_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 1. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri1_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 2. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri2_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 3. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri3_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 4. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri4_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 5. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri5_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 6. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri6_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 7. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri7_cos_queue_id;
+ /* Information about queue configuration. */
+ uint8_t queue_cfg_info;
+ /*
+ * If this flag is set to '1', then the PRI to CoS
+ * configuration is asymmetric on TX and RX sides.
+ * If this flag is set to '0', then PRI to CoS configuration
+ * is symmetric on TX and RX sides.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG \
+ UINT32_C(0x1)
+ uint8_t unused_0[6];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_queue_pri2cos_cfg *
+ **************************/
+
+
+/* hwrm_queue_pri2cos_cfg_input (size:320b/40B) */
+struct hwrm_queue_pri2cos_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX, or both directions applicable to the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_MASK UINT32_C(0x3)
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_SFT 0
+ /* tx path */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ /* Bi-directional (Symmetrically applicable to TX and RX paths) */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR UINT32_C(0x2)
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR
+ /*
+ * When this bit is set to '0', the mapping is requested
+ * for PRI from tunnel headers.
+ * When this bit is set to '1', the mapping is requested
+ * for PRI from inner packet headers.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_IVLAN UINT32_C(0x4)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the pri0_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI0_COS_QUEUE_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the pri1_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI1_COS_QUEUE_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the pri2_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI2_COS_QUEUE_ID \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the pri3_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI3_COS_QUEUE_ID \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the pri4_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI4_COS_QUEUE_ID \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the pri5_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI5_COS_QUEUE_ID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the pri6_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI6_COS_QUEUE_ID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the pri7_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI7_COS_QUEUE_ID \
+ UINT32_C(0x80)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ /*
+ * CoS Queue assigned to priority 0. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri0_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 1. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri1_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 2 This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri2_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 3. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri3_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 4. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri4_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 5. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri5_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 6. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri6_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 7. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri7_cos_queue_id;
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_queue_pri2cos_cfg_output (size:128b/16B) */
+struct hwrm_queue_pri2cos_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_queue_cos2bw_qcfg *
+ **************************/
+
+
+/* hwrm_queue_cos2bw_qcfg_input (size:192b/24B) */
+struct hwrm_queue_cos2bw_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure TC BW assignment on this port.
+ */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_queue_cos2bw_qcfg_output (size:896b/112B) */
+struct hwrm_queue_cos2bw_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* ID of CoS Queue 0. */
+ uint8_t queue_id0;
+ uint8_t unused_0;
+ uint16_t unused_1;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id0_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id0_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id0_bw_weight;
+ /* ID of CoS Queue 1. */
+ uint8_t queue_id1;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id1_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id1_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id1_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id1_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id1_bw_weight;
+ /* ID of CoS Queue 2. */
+ uint8_t queue_id2;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id2_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id2_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id2_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id2_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id2_bw_weight;
+ /* ID of CoS Queue 3. */
+ uint8_t queue_id3;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id3_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id3_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id3_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id3_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id3_bw_weight;
+ /* ID of CoS Queue 4. */
+ uint8_t queue_id4;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id4_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id4_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id4_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id4_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id4_bw_weight;
+ /* ID of CoS Queue 5. */
+ uint8_t queue_id5;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id5_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id5_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id5_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id5_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id5_bw_weight;
+ /* ID of CoS Queue 6. */
+ uint8_t queue_id6;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id6_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id6_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id6_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id6_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id6_bw_weight;
+ /* ID of CoS Queue 7. */
+ uint8_t queue_id7;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id7_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id7_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id7_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id7_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id7_bw_weight;
+ uint8_t unused_2[4];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_queue_cos2bw_cfg *
+ *************************/
+
+
+/* hwrm_queue_cos2bw_cfg_input (size:1024b/128B) */
+struct hwrm_queue_cos2bw_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ uint32_t enables;
+ /*
+ * If this bit is set to 1, then all queue_id0 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID0_VALID \
+ UINT32_C(0x1)
+ /*
+ * If this bit is set to 1, then all queue_id1 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID1_VALID \
+ UINT32_C(0x2)
+ /*
+ * If this bit is set to 1, then all queue_id2 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID2_VALID \
+ UINT32_C(0x4)
+ /*
+ * If this bit is set to 1, then all queue_id3 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID3_VALID \
+ UINT32_C(0x8)
+ /*
+ * If this bit is set to 1, then all queue_id4 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID4_VALID \
+ UINT32_C(0x10)
+ /*
+ * If this bit is set to 1, then all queue_id5 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID5_VALID \
+ UINT32_C(0x20)
+ /*
+ * If this bit is set to 1, then all queue_id6 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID6_VALID \
+ UINT32_C(0x40)
+ /*
+ * If this bit is set to 1, then all queue_id7 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID7_VALID \
+ UINT32_C(0x80)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure TC BW assignment on this port.
+ */
+ uint16_t port_id;
+ /* ID of CoS Queue 0. */
+ uint8_t queue_id0;
+ uint8_t unused_0;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id0_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id0_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id0_bw_weight;
+ /* ID of CoS Queue 1. */
+ uint8_t queue_id1;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id1_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id1_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id1_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id1_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id1_bw_weight;
+ /* ID of CoS Queue 2. */
+ uint8_t queue_id2;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id2_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id2_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id2_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id2_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id2_bw_weight;
+ /* ID of CoS Queue 3. */
+ uint8_t queue_id3;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id3_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id3_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id3_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id3_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id3_bw_weight;
+ /* ID of CoS Queue 4. */
+ uint8_t queue_id4;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id4_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id4_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id4_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id4_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id4_bw_weight;
+ /* ID of CoS Queue 5. */
+ uint8_t queue_id5;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id5_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id5_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id5_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id5_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id5_bw_weight;
+ /* ID of CoS Queue 6. */
+ uint8_t queue_id6;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id6_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id6_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id6_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id6_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id6_bw_weight;
+ /* ID of CoS Queue 7. */
+ uint8_t queue_id7;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id7_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id7_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id7_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id7_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id7_bw_weight;
+ uint8_t unused_1[5];
+} __rte_packed;
+
+/* hwrm_queue_cos2bw_cfg_output (size:128b/16B) */
+struct hwrm_queue_cos2bw_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_queue_dscp_qcaps *
+ *************************/
+
+
+/* hwrm_queue_dscp_qcaps_input (size:192b/24B) */
+struct hwrm_queue_dscp_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_queue_dscp_qcaps_output (size:128b/16B) */
+struct hwrm_queue_dscp_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The number of bits provided by the hardware for the DSCP value. */
+ uint8_t num_dscp_bits;
+ uint8_t unused_0;
+ /* Max number of DSCP-MASK-PRI entries supported. */
+ uint16_t max_entries;
+ uint8_t unused_1[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/****************************
+ * hwrm_queue_dscp2pri_qcfg *
+ ****************************/
+
+
+/* hwrm_queue_dscp2pri_qcfg_input (size:256b/32B) */
+struct hwrm_queue_dscp2pri_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the 24-bits DSCP-MASK-PRI
+ * tuple(s) will be copied to.
+ */
+ uint64_t dest_data_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0;
+ /* Size of the buffer pointed to by dest_data_addr. */
+ uint16_t dest_data_buffer_size;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_queue_dscp2pri_qcfg_output (size:128b/16B) */
+struct hwrm_queue_dscp2pri_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * A count of the number of DSCP-MASK-PRI tuple(s) pointed to
+ * by the dest_data_addr.
+ */
+ uint16_t entry_cnt;
+ /*
+ * This is the default PRI which un-initialized DSCP values are
+ * mapped to.
+ */
+ uint8_t default_pri;
+ uint8_t unused_0[4];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_queue_dscp2pri_cfg *
+ ***************************/
+
+
+/* hwrm_queue_dscp2pri_cfg_input (size:320b/40B) */
+struct hwrm_queue_dscp2pri_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the 24-bits DSCP-MASK-PRI tuple
+ * will be copied from.
+ */
+ uint64_t src_data_addr;
+ uint32_t flags;
+ /* use_hw_default_pri is 1 b */
+ #define HWRM_QUEUE_DSCP2PRI_CFG_INPUT_FLAGS_USE_HW_DEFAULT_PRI \
+ UINT32_C(0x1)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the default_pri field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_DSCP2PRI_CFG_INPUT_ENABLES_DEFAULT_PRI \
+ UINT32_C(0x1)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ /*
+ * This is the default PRI which un-initialized DSCP values will be
+ * mapped to.
+ */
+ uint8_t default_pri;
+ /*
+ * A count of the number of DSCP-MASK-PRI tuple(s) in the data pointed
+ * to by src_data_addr.
+ */
+ uint16_t entry_cnt;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_queue_dscp2pri_cfg_output (size:128b/16B) */
+struct hwrm_queue_dscp2pri_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_queue_mpls_qcaps *
+ *************************/
+
+
+/* hwrm_queue_mpls_qcaps_input (size:192b/24B) */
+struct hwrm_queue_mpls_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure MPLS TC(EXP) to pri mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_queue_mpls_qcaps_output (size:128b/16B) */
+struct hwrm_queue_mpls_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_mplstc2pri_cfg command.
+ *
+ * Each bit represents a specific pri where bit 0 represents
+ * pri 0 and bit 7 represents pri 7.
+ * # A value of 0 indicates that the pri is not configurable
+ * by the hwrm_queue_mplstc2pri_cfg command.
+ * # A value of 1 indicates that the pri is configurable.
+ * # A hwrm_queue_mplstc2pri_cfg command shall return error when
+ * trying to configure a pri that is not configurable.
+ */
+ uint8_t queue_mplstc2pri_cfg_allowed;
+ /*
+ * This is the default PRI which un-initialized MPLS values will be
+ * mapped to.
+ */
+ uint8_t hw_default_pri;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************************
+ * hwrm_queue_mplstc2pri_qcfg *
+ ******************************/
+
+
+/* hwrm_queue_mplstc2pri_qcfg_input (size:192b/24B) */
+struct hwrm_queue_mplstc2pri_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure MPLS TC(EXP) to pri mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_queue_mplstc2pri_qcfg_output (size:192b/24B) */
+struct hwrm_queue_mplstc2pri_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * pri assigned to MPLS TC(EXP) 0. This value can only be changed
+ * before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 0.
+ */
+ uint8_t tc0_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 1. This value can only be changed
+ * before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 1.
+ */
+ uint8_t tc1_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 2. This value can only be changed
+ * before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 2.
+ */
+ uint8_t tc2_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 3. This value can only be changed
+ * before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 3.
+ */
+ uint8_t tc3_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 4. This value can only be changed
+ * before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 4.
+ */
+ uint8_t tc4_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 5. This value can only be changed
+ * before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 5.
+ */
+ uint8_t tc5_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 6. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 6.
+ */
+ uint8_t tc6_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 7. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no pri is assigned to the
+ * MPLS TC(EXP) 7.
+ */
+ uint8_t tc7_pri_queue_id;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*****************************
+ * hwrm_queue_mplstc2pri_cfg *
+ *****************************/
+
+
+/* hwrm_queue_mplstc2pri_cfg_input (size:256b/32B) */
+struct hwrm_queue_mplstc2pri_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the mplstc0_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC0_PRI_QUEUE_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the mplstc1_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC1_PRI_QUEUE_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the mplstc2_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC2_PRI_QUEUE_ID \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the mplstc3_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC3_PRI_QUEUE_ID \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the mplstc4_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC4_PRI_QUEUE_ID \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the mplstc5_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC5_PRI_QUEUE_ID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the mplstc6_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC6_PRI_QUEUE_ID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the mplstc7_pri_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_MPLSTC2PRI_CFG_INPUT_ENABLES_TC7_PRI_QUEUE_ID \
+ UINT32_C(0x80)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure MPLS TC(EXP)to pri mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0[3];
+ /*
+ * pri assigned to MPLS TC(EXP) 0. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc0_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 1. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc1_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 2 This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc2_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 3. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc3_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 4. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc4_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 5. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc5_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 6. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc6_pri_queue_id;
+ /*
+ * pri assigned to MPLS TC(EXP) 7. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t tc7_pri_queue_id;
+} __rte_packed;
+
+/* hwrm_queue_mplstc2pri_cfg_output (size:128b/16B) */
+struct hwrm_queue_mplstc2pri_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************
+ * hwrm_vnic_alloc *
+ *******************/
+
+
+/* hwrm_vnic_alloc_input (size:192b/24B) */
+struct hwrm_vnic_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * When this bit is '1', this VNIC is requested to
+ * be the default VNIC for this function.
+ */
+ #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_vnic_alloc_output (size:128b/16B) */
+struct hwrm_vnic_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************
+ * hwrm_vnic_free *
+ ******************/
+
+
+/* hwrm_vnic_free_input (size:192b/24B) */
+struct hwrm_vnic_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_vnic_free_output (size:128b/16B) */
+struct hwrm_vnic_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*****************
+ * hwrm_vnic_cfg *
+ *****************/
+
+
+/* hwrm_vnic_cfg_input (size:384b/48B) */
+struct hwrm_vnic_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is requested to
+ * be the default VNIC for the function.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is being configured to
+ * strip VLAN in the RX path.
+ * If set to '0', then VLAN stripping is disabled on
+ * this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is being configured to
+ * buffer receive packets in the hardware until the host
+ * posts new receive buffers.
+ * If set to '0', then bd_stall is being configured to be
+ * disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is being configured to
+ * receive both RoCE and non-RoCE traffic.
+ * If set to '0', then this VNIC is not configured to be
+ * operating in dual VNIC mode.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE \
+ UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is requested to
+ * be configured to receive only RoCE traffic.
+ * If this flag is set to '0', then this flag shall be
+ * ignored by the HWRM.
+ * If roce_dual_vnic_mode flag is set to '1'
+ * or roce_mirroring_capable_vnic_mode flag to 1,
+ * then the HWRM client shall not set this flag to '1'.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE \
+ UINT32_C(0x10)
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where
+ * exact match is used to direct packets to a VNIC with one
+ * destination ring group only, there is no need to configure
+ * RSS indirection table for that VNIC as only one destination
+ * ring group is used.
+ *
+ * This flag is used to enable a mode where
+ * RSS is enabled in the VNIC using a RSS context
+ * for computing RSS hash but the RSS indirection table is
+ * not configured using hwrm_vnic_rss_cfg.
+ *
+ * If this mode is enabled, then the driver should not program
+ * RSS indirection table for the RSS context that is used for
+ * computing RSS hash only.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_RSS_DFLT_CR_MODE \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is being configured to
+ * receive both RoCE and non-RoCE traffic, but forward only the
+ * RoCE traffic further. Also, RoCE traffic can be mirrored to
+ * L2 driver.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE \
+ UINT32_C(0x40)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the dflt_ring_grp field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the rss_rule field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the cos_rule field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the lb_rule field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the mru field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the default_rx_ring_id field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DEFAULT_RX_RING_ID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the default_cmpl_ring_id field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DEFAULT_CMPL_RING_ID \
+ UINT32_C(0x40)
+ /* This bit must be '1' for the queue_id field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_QUEUE_ID \
+ UINT32_C(0x80)
+ /* This bit must be '1' for the rx_csum_v2_mode field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_RX_CSUM_V2_MODE \
+ UINT32_C(0x100)
+ /* Logical vnic ID */
+ uint16_t vnic_id;
+ /*
+ * Default Completion ring for the VNIC. This ring will
+ * be chosen if packet does not match any RSS rules and if
+ * there is no COS rule.
+ */
+ uint16_t dflt_ring_grp;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for load balancing rule/table structure.
+ * 0xFF... (All Fs) if there is no LB rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * The maximum receive unit of the vnic.
+ * Each vnic is associated with a function.
+ * The vnic mru value overwrites the mru setting of the
+ * associated function.
+ * The HWRM shall make sure that vnic mru does not exceed
+ * the mru of the port the function is associated with.
+ */
+ uint16_t mru;
+ /*
+ * Default Rx ring for the VNIC. This ring will
+ * be chosen if packet does not match any RSS rules.
+ * The aggregation ring associated with the Rx ring is
+ * implied based on the Rx ring specified when the
+ * aggregation ring was allocated.
+ */
+ uint16_t default_rx_ring_id;
+ /*
+ * Default completion ring for the VNIC. This ring will
+ * be chosen if packet does not match any RSS rules.
+ */
+ uint16_t default_cmpl_ring_id;
+ /*
+ * When specified, only incoming packets classified to the specified CoS
+ * queue ID will be arriving on this VNIC. Packet priority to CoS mapping
+ * rules can be specified using HWRM_QUEUE_PRI2COS_CFG. In this mode,
+ * ntuple filters with VNIC destination specified are invalid since they
+ * conflict with the CoS to VNIC steering rules in this mode.
+ *
+ * If this field is not specified, packet to VNIC steering will be
+ * subject to the standard L2 filter rules and any additional ntuple
+ * filter rules with destination VNIC specified.
+ */
+ uint16_t queue_id;
+ /*
+ * If the device supports the RX V2 and RX TPA start V2 completion
+ * records as indicated by the HWRM_VNIC_QCAPS command, this field is
+ * used to specify the two RX checksum modes supported by these
+ * completion records.
+ */
+ uint8_t rx_csum_v2_mode;
+ /*
+ * When configured with this checksum mode, the number of header
+ * groups in the delivered packet with a valid IP checksum and
+ * the number of header groups in the delivered packet with a valid
+ * L4 checksum are reported. Valid checksums are counted from the
+ * outermost header group to the innermost header group, stopping at
+ * the first error. This is the default checksum mode supported if
+ * the driver doesn't explicitly configure the RX checksum mode.
+ */
+ #define HWRM_VNIC_CFG_INPUT_RX_CSUM_V2_MODE_DEFAULT UINT32_C(0x0)
+ /*
+ * When configured with this checksum mode, the checksum status is
+ * reported using 'all ok' mode. In the RX completion record, one
+ * bit indicates if the IP checksum is valid for all the parsed
+ * header groups with an IP checksum. Another bit indicates if the
+ * L4 checksum is valid for all the parsed header groups with an L4
+ * checksum. The number of header groups that were parsed by the
+ * chip and passed in the delivered packet is also reported.
+ */
+ #define HWRM_VNIC_CFG_INPUT_RX_CSUM_V2_MODE_ALL_OK UINT32_C(0x1)
+ /*
+ * Any rx_csum_v2_mode value larger than or equal to this is not
+ * valid
+ */
+ #define HWRM_VNIC_CFG_INPUT_RX_CSUM_V2_MODE_MAX UINT32_C(0x2)
+ #define HWRM_VNIC_CFG_INPUT_RX_CSUM_V2_MODE_LAST \
+ HWRM_VNIC_CFG_INPUT_RX_CSUM_V2_MODE_MAX
+ uint8_t unused0[5];
+} __rte_packed;
+
+/* hwrm_vnic_cfg_output (size:128b/16B) */
+struct hwrm_vnic_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************
+ * hwrm_vnic_qcfg *
+ ******************/
+
+
+/* hwrm_vnic_qcfg_input (size:256b/32B) */
+struct hwrm_vnic_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the vf_id_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_QCFG_INPUT_ENABLES_VF_ID_VALID UINT32_C(0x1)
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+ /* ID of Virtual Function whose VNIC resource is being queried. */
+ uint16_t vf_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_vnic_qcfg_output (size:256b/32B) */
+struct hwrm_vnic_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Default Completion ring for the VNIC. */
+ uint16_t dflt_ring_grp;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for load balancing rule/table structure.
+ * 0xFF... (All Fs) if there is no LB rule.
+ */
+ uint16_t lb_rule;
+ /* The maximum receive unit of the vnic. */
+ uint16_t mru;
+ uint8_t unused_0[2];
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is the default VNIC for
+ * the function.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_DEFAULT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is configured to
+ * strip VLAN in the RX path.
+ * If set to '0', then VLAN stripping is disabled on
+ * this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_VLAN_STRIP_MODE \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is configured to
+ * buffer receive packets in the hardware until the host
+ * posts new receive buffers.
+ * If set to '0', then bd_stall is disabled on
+ * this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_BD_STALL_MODE \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is configured to
+ * receive both RoCE and non-RoCE traffic.
+ * If set to '0', then this VNIC is not configured to
+ * operate in dual VNIC mode.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_DUAL_VNIC_MODE \
+ UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is configured to
+ * receive only RoCE traffic.
+ * When this flag is set to '0', the VNIC is not configured
+ * to receive only RoCE traffic.
+ * If roce_dual_vnic_mode flag and this flag both are set
+ * to '1', then it is an invalid configuration of the
+ * VNIC. The HWRM should not allow that type of
+ * mis-configuration by HWRM clients.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_ONLY_VNIC_MODE \
+ UINT32_C(0x10)
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where
+ * exact match is used to direct packets to a VNIC with one
+ * destination ring group only, there is no need to configure
+ * RSS indirection table for that VNIC as only one destination
+ * ring group is used.
+ *
+ * When this bit is set to '1', then the VNIC is enabled in a
+ * mode where RSS is enabled in the VNIC using a RSS context
+ * for computing RSS hash but the RSS indirection table is
+ * not configured.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_RSS_DFLT_CR_MODE \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is configured to
+ * receive both RoCE and non-RoCE traffic, but forward only
+ * RoCE traffic further. Also RoCE traffic can be mirrored to
+ * L2 driver.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE \
+ UINT32_C(0x40)
+ /*
+ * When returned with a valid CoS Queue id, the CoS Queue/VNIC association
+ * is valid. Otherwise it will return 0xFFFF to indicate no VNIC/CoS
+ * queue association.
+ */
+ uint16_t queue_id;
+ /*
+ * If the device supports the RX V2 and RX TPA start V2 completion
+ * records as indicated by the HWRM_VNIC_QCAPS command, this field is
+ * used to specify the current RX checksum mode configured for all the
+ * RX rings of a VNIC.
+ */
+ uint8_t rx_csum_v2_mode;
+ /*
+ * This value indicates that the VNIC is configured to use the
+ * default RX checksum mode for all the rings associated with this
+ * VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_RX_CSUM_V2_MODE_DEFAULT UINT32_C(0x0)
+ /*
+ * This value indicates that the VNIC is configured to use the RX
+ * checksum ‘all_ok’ mode for all the rings associated with this
+ * VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_RX_CSUM_V2_MODE_ALL_OK UINT32_C(0x1)
+ /*
+ * Any rx_csum_v2_mode value larger than or equal to this is not
+ * valid
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_RX_CSUM_V2_MODE_MAX UINT32_C(0x2)
+ #define HWRM_VNIC_QCFG_OUTPUT_RX_CSUM_V2_MODE_LAST \
+ HWRM_VNIC_QCFG_OUTPUT_RX_CSUM_V2_MODE_MAX
+ uint8_t unused_1[4];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************
+ * hwrm_vnic_qcaps *
+ *******************/
+
+
+/* hwrm_vnic_qcaps_input (size:192b/24B) */
+struct hwrm_vnic_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_vnic_qcaps_output (size:192b/24B) */
+struct hwrm_vnic_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The maximum receive unit that is settable on a vnic. */
+ uint16_t mru;
+ uint8_t unused_0[2];
+ uint32_t flags;
+ /* Unused. */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_UNUSED \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the capability of stripping VLAN in
+ * the RX path is supported on VNIC(s).
+ * If set to '0', then VLAN stripping capability is
+ * not supported on VNIC(s).
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_VLAN_STRIP_CAP \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the capability to buffer receive
+ * packets in the hardware until the host posts new receive buffers
+ * is supported on VNIC(s).
+ * If set to '0', then bd_stall capability is not supported
+ * on VNIC(s).
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_BD_STALL_CAP \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the capability to
+ * receive both RoCE and non-RoCE traffic on VNIC(s) is
+ * supported.
+ * If set to '0', then the capability to receive
+ * both RoCE and non-RoCE traffic on VNIC(s) is
+ * not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_DUAL_VNIC_CAP \
+ UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', the capability to configure
+ * a VNIC to receive only RoCE traffic is supported.
+ * When this flag is set to '0', the VNIC capability to
+ * configure to receive only RoCE traffic is not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_ONLY_VNIC_CAP \
+ UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', then the capability to enable
+ * a VNIC in a mode where RSS context without configuring
+ * RSS indirection table is supported (for RSS hash computation).
+ * When this bit is set to '0', then a VNIC can not be configured
+ * with a mode to enable RSS context without configuring RSS
+ * indirection table.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_RSS_DFLT_CR_CAP \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1', the capability to
+ * mirror the the RoCE traffic is supported.
+ * If set to '0', then the capability to mirror the
+ * RoCE traffic is not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_CAP \
+ UINT32_C(0x40)
+ /*
+ * When this bit is '1', the outermost RSS hashing capability
+ * is supported. If set to '0', then the outermost RSS hashing
+ * capability is not supported.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_OUTERMOST_RSS_CAP \
+ UINT32_C(0x80)
+ /*
+ * When this bit is '1', it indicates that firmware supports the
+ * ability to steer incoming packets from one CoS queue to one
+ * VNIC. This optional feature can then be enabled
+ * using HWRM_VNIC_CFG on any VNIC. This feature is only
+ * available when NVM option “enable_cos_classfication” is set
+ * to 1. If set to '0', firmware does not support this feature.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_COS_ASSIGNMENT_CAP \
+ UINT32_C(0x100)
+ /*
+ * When this bit is '1', it indicates that HW and firmware supports
+ * the use of RX V2 and RX TPA start V2 completion records for all
+ * the RX rings of a VNIC. Once set, this feature is mandatory to
+ * be used for the RX rings of the VNIC. Additionally, two new RX
+ * checksum features supported by these ompletion records can be
+ * configured using the HWRM_VNIC_CFG on a VNIC. If set to '0', the
+ * HW and the firmware does not support this feature.
+ */
+ #define HWRM_VNIC_QCAPS_OUTPUT_FLAGS_RX_CMPL_V2_CAP \
+ UINT32_C(0x200)
+ /*
+ * This field advertises the maximum concurrent TPA aggregations
+ * supported by the VNIC on new devices that support TPA v2.
+ * '0' means that TPA v2 is not supported.
+ */
+ uint16_t max_aggs_supported;
+ uint8_t unused_1[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************
+ * hwrm_vnic_tpa_cfg *
+ *********************/
+
+
+/* hwrm_vnic_tpa_cfg_input (size:320b/40B) */
+struct hwrm_vnic_tpa_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) of
+ * non-tunneled TCP packets.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_TPA \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) of
+ * tunneled TCP packets.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_ENCAP_TPA \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) according
+ * to Windows Receive Segment Coalescing (RSC) rules.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_RSC_WND_UPDATE \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) according
+ * to Linux Generic Receive Offload (GRO) rules.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) for TCP
+ * packets with IP ECN set to non-zero.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_ECN \
+ UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) for
+ * GRE tunneled TCP packets only if all packets have the
+ * same GRE sequence.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1' and the GRO mode is enabled,
+ * the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) for
+ * TCP/IPv4 packets with consecutively increasing IPIDs.
+ * In other words, the last packet that is being
+ * aggregated to an already existing aggregation context
+ * shall have IPID 1 more than the IPID of the last packet
+ * that was aggregated in that aggregation context.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_IPID_CHECK \
+ UINT32_C(0x40)
+ /*
+ * When this bit is '1' and the GRO mode is enabled,
+ * the VNIC shall be configured to
+ * perform transparent packet aggregation (TPA) for
+ * TCP packets with the same TTL (IPv4) or Hop limit (IPv6)
+ * value.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_TTL_CHECK \
+ UINT32_C(0x80)
+ /*
+ * When this bit is '1' and the GRO mode is enabled,
+ * the VNIC shall DMA payload data using GRO rules.
+ * When this bit is '0', the VNIC shall DMA payload data
+ * using the more efficient LRO rules of filling all
+ * aggregation buffers.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_PACK_AS_GRO \
+ UINT32_C(0x100)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the max_agg_segs field to be
+ * configured.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_SEGS UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the max_aggs field to be
+ * configured.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGGS UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the max_agg_timer field to be
+ * configured.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_TIMER UINT32_C(0x4)
+ /* deprecated bit. Do not use!!! */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MIN_AGG_LEN UINT32_C(0x8)
+ /* Logical vnic ID */
+ uint16_t vnic_id;
+ /*
+ * This is the maximum number of TCP segments that can
+ * be aggregated (unit is Log2). Max value is 31. On new
+ * devices supporting TPA v2, the unit is multiples of 4 and
+ * valid values are > 0 and <= 63.
+ */
+ uint16_t max_agg_segs;
+ /* 1 segment */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_1 UINT32_C(0x0)
+ /* 2 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_2 UINT32_C(0x1)
+ /* 4 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_4 UINT32_C(0x2)
+ /* 8 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_8 UINT32_C(0x3)
+ /* Any segment size larger than this is not valid */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX UINT32_C(0x1f)
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_LAST \
+ HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX
+ /*
+ * This is the maximum number of aggregations this VNIC is
+ * allowed (unit is Log2). Max value is 7. On new devices
+ * supporting TPA v2, this is in unit of 1 and must be > 0
+ * and <= max_aggs_supported in the hwrm_vnic_qcaps response
+ * to enable TPA v2.
+ */
+ uint16_t max_aggs;
+ /* 1 aggregation */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_1 UINT32_C(0x0)
+ /* 2 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_2 UINT32_C(0x1)
+ /* 4 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_4 UINT32_C(0x2)
+ /* 8 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_8 UINT32_C(0x3)
+ /* 16 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_16 UINT32_C(0x4)
+ /* Any aggregation size larger than this is not valid */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX UINT32_C(0x7)
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_LAST \
+ HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX
+ uint8_t unused_0[2];
+ /*
+ * This is the maximum amount of time allowed for
+ * an aggregation context to complete after it was initiated.
+ */
+ uint32_t max_agg_timer;
+ /*
+ * This is the minimum amount of payload length required to
+ * start an aggregation context. This field is deprecated and
+ * should be set to 0. The minimum length is set by firmware
+ * and can be queried using hwrm_vnic_tpa_qcfg.
+ */
+ uint32_t min_agg_len;
+} __rte_packed;
+
+/* hwrm_vnic_tpa_cfg_output (size:128b/16B) */
+struct hwrm_vnic_tpa_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************
+ * hwrm_vnic_rss_cfg *
+ *********************/
+
+
+/* hwrm_vnic_rss_cfg_input (size:384b/48B) */
+struct hwrm_vnic_rss_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source and destination IPv4 addresses of IPv4
+ * packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 UINT32_C(0x1)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv4 addresses and
+ * source/destination ports of TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv4 addresses and
+ * source/destination ports of UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source and destination IPv4 addresses of IPv6
+ * packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv6 addresses and
+ * source/destination ports of TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv6 addresses and
+ * source/destination ports of UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20)
+ /* VNIC ID of VNIC associated with RSS table being configured. */
+ uint16_t vnic_id;
+ /*
+ * Specifies which VNIC ring table pair to configure.
+ * Valid values range from 0 to 7.
+ */
+ uint8_t ring_table_pair_index;
+ /* Flags to specify different RSS hash modes. */
+ uint8_t hash_mode_flags;
+ /*
+ * When this bit is '1', it indicates using current RSS
+ * hash mode setting configured in the device.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_DEFAULT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over innermost 4 tuples {l3.src, l3.dest,
+ * l4.src, l4.dest} for tunnel packets. For none-tunnel
+ * packets, the RSS hash is computed over the normal
+ * src/dest l3 and src/dest l4 headers.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_INNERMOST_4 \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over innermost 2 tuples {l3.src, l3.dest} for
+ * tunnel packets. For none-tunnel packets, the RSS hash is
+ * computed over the normal src/dest l3 headers.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_INNERMOST_2 \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over outermost 4 tuples {t_l3.src, t_l3.dest,
+ * t_l4.src, t_l4.dest} for tunnel packets. For none-tunnel
+ * packets, the RSS hash is computed over the normal
+ * src/dest l3 and src/dest l4 headers.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_OUTERMOST_4 \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over outermost 2 tuples {t_l3.src, t_l3.dest} for
+ * tunnel packets. For none-tunnel packets, the RSS hash is
+ * computed over the normal src/dest l3 headers.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_MODE_FLAGS_OUTERMOST_2 \
+ UINT32_C(0x10)
+ /* This is the address for rss ring group table */
+ uint64_t ring_grp_tbl_addr;
+ /* This is the address for rss hash key table */
+ uint64_t hash_key_tbl_addr;
+ /* Index to the rss indirection table. */
+ uint16_t rss_ctx_idx;
+ uint8_t unused_1[6];
+} __rte_packed;
+
+/* hwrm_vnic_rss_cfg_output (size:128b/16B) */
+struct hwrm_vnic_rss_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* hwrm_vnic_rss_cfg_cmd_err (size:64b/8B) */
+struct hwrm_vnic_rss_cfg_cmd_err {
+ /*
+ * command specific error codes that goes to
+ * the cmd_err field in Common HWRM Error Response.
+ */
+ uint8_t code;
+ /* Unknown error */
+ #define HWRM_VNIC_RSS_CFG_CMD_ERR_CODE_UNKNOWN \
+ UINT32_C(0x0)
+ /*
+ * Unable to change global RSS mode to outer due to all active
+ * interfaces are not ready to support outer RSS hashing.
+ */
+ #define HWRM_VNIC_RSS_CFG_CMD_ERR_CODE_INTERFACE_NOT_READY \
+ UINT32_C(0x1)
+ #define HWRM_VNIC_RSS_CFG_CMD_ERR_CODE_LAST \
+ HWRM_VNIC_RSS_CFG_CMD_ERR_CODE_INTERFACE_NOT_READY
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/**********************
+ * hwrm_vnic_rss_qcfg *
+ **********************/
+
+
+/* hwrm_vnic_rss_qcfg_input (size:192b/24B) */
+struct hwrm_vnic_rss_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Index to the rss indirection table. */
+ uint16_t rss_ctx_idx;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_vnic_rss_qcfg_output (size:512b/64B) */
+struct hwrm_vnic_rss_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source and destination IPv4 addresses of IPv4
+ * packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_IPV4 UINT32_C(0x1)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv4 addresses and
+ * source/destination ports of TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv4 addresses and
+ * source/destination ports of UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source and destination IPv4 addresses of IPv6
+ * packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv6 addresses and
+ * source/destination ports of TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10)
+ /*
+ * When this bit is '1', the RSS hash shall be computed
+ * over source/destination IPv6 addresses and
+ * source/destination ports of UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20)
+ uint8_t unused_0[4];
+ /* This is the value of rss hash key */
+ uint32_t hash_key[10];
+ /* Flags to specify different RSS hash modes. */
+ uint8_t hash_mode_flags;
+ /*
+ * When this bit is '1', it indicates using current RSS
+ * hash mode setting configured in the device.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_DEFAULT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over innermost 4 tuples {l3.src, l3.dest,
+ * l4.src, l4.dest} for tunnel packets. For none-tunnel
+ * packets, the RSS hash is computed over the normal
+ * src/dest l3 and src/dest l4 headers.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_INNERMOST_4 \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over innermost 2 tuples {l3.src, l3.dest} for
+ * tunnel packets. For none-tunnel packets, the RSS hash is
+ * computed over the normal src/dest l3 headers.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_INNERMOST_2 \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over outermost 4 tuples {t_l3.src, t_l3.dest,
+ * t_l4.src, t_l4.dest} for tunnel packets. For none-tunnel
+ * packets, the RSS hash is computed over the normal
+ * src/dest l3 and src/dest l4 headers.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_OUTERMOST_4 \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', it indicates requesting support of
+ * RSS hashing over outermost 2 tuples {t_l3.src, t_l3.dest} for
+ * tunnel packets. For none-tunnel packets, the RSS hash is
+ * computed over the normal src/dest l3 headers.
+ */
+ #define HWRM_VNIC_RSS_QCFG_OUTPUT_HASH_MODE_FLAGS_OUTERMOST_2 \
+ UINT32_C(0x10)
+ uint8_t unused_1[6];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_vnic_plcmodes_cfg *
+ **************************/
+
+
+/* hwrm_vnic_plcmodes_cfg_input (size:320b/40B) */
+struct hwrm_vnic_plcmodes_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to
+ * use regular placement algorithm.
+ * By default, the regular placement algorithm shall be
+ * enabled on the VNIC.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_REGULAR_PLACEMENT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC shall be configured
+ * use the jumbo placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_JUMBO_PLACEMENT \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC shall be configured
+ * to enable Header-Data split for IPv4 packets according
+ * to the following rules:
+ * # If the packet is identified as TCP/IPv4, then the
+ * packet is split at the beginning of the TCP payload.
+ * # If the packet is identified as UDP/IPv4, then the
+ * packet is split at the beginning of UDP payload.
+ * # If the packet is identified as non-TCP and non-UDP
+ * IPv4 packet, then the packet is split at the beginning
+ * of the upper layer protocol header carried in the IPv4
+ * packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV4 \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC shall be configured
+ * to enable Header-Data split for IPv6 packets according
+ * to the following rules:
+ * # If the packet is identified as TCP/IPv6, then the
+ * packet is split at the beginning of the TCP payload.
+ * # If the packet is identified as UDP/IPv6, then the
+ * packet is split at the beginning of UDP payload.
+ * # If the packet is identified as non-TCP and non-UDP
+ * IPv6 packet, then the packet is split at the beginning
+ * of the upper layer protocol header carried in the IPv6
+ * packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV6 \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC shall be configured
+ * to enable Header-Data split for FCoE packets at the
+ * beginning of FC payload.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_FCOE \
+ UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC shall be configured
+ * to enable Header-Data split for RoCE packets at the
+ * beginning of RoCE payload (after BTH/GRH headers).
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_ROCE \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC shall be configured use the virtio
+ * placement algorithm. This feature can only be configured when
+ * proxy mode is supported on the function.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_VIRTIO_PLACEMENT \
+ UINT32_C(0x40)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the jumbo_thresh_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_JUMBO_THRESH_VALID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the hds_offset_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_OFFSET_VALID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the hds_threshold_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_THRESHOLD_VALID \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the max_bds_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_MAX_BDS_VALID \
+ UINT32_C(0x8)
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+ /*
+ * When jumbo placement algorithm is enabled, this value
+ * is used to determine the threshold for jumbo placement.
+ * Packets with length larger than this value will be
+ * placed according to the jumbo placement algorithm.
+ */
+ uint16_t jumbo_thresh;
+ /*
+ * This value is used to determine the offset into
+ * packet buffer where the split data (payload) will be
+ * placed according to one of HDS placement algorithm.
+ *
+ * The lengths of packet buffers provided for split data
+ * shall be larger than this value.
+ */
+ uint16_t hds_offset;
+ /*
+ * When one of the HDS placement algorithm is enabled, this
+ * value is used to determine the threshold for HDS
+ * placement.
+ * Packets with length larger than this value will be
+ * placed according to the HDS placement algorithm.
+ * This value shall be in multiple of 4 bytes.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When virtio placement algorithm is enabled, this
+ * value is used to determine the the maximum number of BDs
+ * that can be used to place an Rx Packet.
+ * If an incoming packet does not fit in the buffers described
+ * by the max BDs, the packet will be dropped and an error
+ * will be reported in the completion. Valid values for this
+ * field are between 1 and 8. If the VNIC uses header-data-
+ * separation and/or TPA with buffer spanning enabled, valid
+ * values for this field are between 2 and 8.
+ * This feature can only be configured when proxy mode is
+ * supported on the function.
+ */
+ uint16_t max_bds;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_vnic_plcmodes_cfg_output (size:128b/16B) */
+struct hwrm_vnic_plcmodes_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
+ * processor, the order of writes has to be such that this field is
+ * written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_vnic_plcmodes_qcfg *
+ ***************************/
+
+
+/* hwrm_vnic_plcmodes_qcfg_input (size:192b/24B) */
+struct hwrm_vnic_plcmodes_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Logical vnic ID */
+ uint32_t vnic_id;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_vnic_plcmodes_qcfg_output (size:192b/24B) */
+struct hwrm_vnic_plcmodes_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is configured to
+ * use regular placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_REGULAR_PLACEMENT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is configured to
+ * use the jumbo placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_JUMBO_PLACEMENT \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is configured
+ * to enable Header-Data split for IPv4 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV4 \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is configured
+ * to enable Header-Data split for IPv6 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV6 \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC is configured
+ * to enable Header-Data split for FCoE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_FCOE \
+ UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC is configured
+ * to enable Header-Data split for RoCE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_ROCE \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is configured
+ * to be the default VNIC of the requesting function.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_DFLT_VNIC \
+ UINT32_C(0x40)
+ /*
+ * When this bit is '1', the VNIC is configured to use the virtio
+ * placement algorithm. This feature can only be configured when
+ * proxy mode is supported on the function.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_VIRTIO_PLACEMENT \
+ UINT32_C(0x80)
+ /*
+ * When jumbo placement algorithm is enabled, this value
+ * is used to determine the threshold for jumbo placement.
+ * Packets with length larger than this value will be
+ * placed according to the jumbo placement algorithm.
+ */
+ uint16_t jumbo_thresh;
+ /*
+ * This value is used to determine the offset into
+ * packet buffer where the split data (payload) will be
+ * placed according to one of HDS placement algorithm.
+ *
+ * The lengths of packet buffers provided for split data
+ * shall be larger than this value.
+ */
+ uint16_t hds_offset;
+ /*
+ * When one of the HDS placement algorithm is enabled, this
+ * value is used to determine the threshold for HDS
+ * placement.
+ * Packets with length larger than this value will be
+ * placed according to the HDS placement algorithm.
+ * This value shall be in multiple of 4 bytes.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When virtio placement algorithm is enabled, this
+ * value is used to determine the the maximum number of BDs
+ * that can be used to place an Rx Packet.
+ * If an incoming packet does not fit in the buffers described
+ * by the max BDs, the packet will be dropped and an error
+ * will be reported in the completion. Valid values for this
+ * field are between 1 and 8. If the VNIC uses header-data-
+ * separation and/or TPA with buffer spanning enabled, valid
+ * values for this field are between 2 and 8.
+ * This feature can only be configured when proxy mode is supported
+ * on the function
+ */
+ uint16_t max_bds;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
+ * processor, the order of writes has to be such that this field is
+ * written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************************
+ * hwrm_vnic_rss_cos_lb_ctx_alloc *
+ **********************************/
+
+
+/* hwrm_vnic_rss_cos_lb_ctx_alloc_input (size:128b/16B) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_vnic_rss_cos_lb_ctx_alloc_output (size:128b/16B) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint16_t rss_cos_lb_ctx_id;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************************
+ * hwrm_vnic_rss_cos_lb_ctx_free *
+ *********************************/
+
+
+/* hwrm_vnic_rss_cos_lb_ctx_free_input (size:192b/24B) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint16_t rss_cos_lb_ctx_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_vnic_rss_cos_lb_ctx_free_output (size:128b/16B) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************
+ * hwrm_ring_alloc *
+ *******************/
+
+
+/* hwrm_ring_alloc_input (size:704b/88B) */
+struct hwrm_ring_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the ring_arb_cfg field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RING_ARB_CFG \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the stat_ctx_id_valid field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the max_bw_valid field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the rx_ring_id field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RX_RING_ID_VALID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the nq_ring_id field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_NQ_RING_ID_VALID \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the rx_buf_size field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RX_BUF_SIZE_VALID \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the schq_id field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_SCHQ_ID \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the mpc_chnls_type field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_MPC_CHNLS_TYPE \
+ UINT32_C(0x400)
+ /* Ring Type. */
+ uint8_t ring_type;
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
+ /* RX Aggregation Ring */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX_AGG UINT32_C(0x4)
+ /* Notification Queue */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_NQ UINT32_C(0x5)
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_LAST \
+ HWRM_RING_ALLOC_INPUT_RING_TYPE_NQ
+ uint8_t unused_0;
+ /* Ring allocation flags. */
+ uint16_t flags;
+ /*
+ * For Rx rings, the incoming packet data can be placed at either
+ * a 0B or 2B offset from the start of the Rx packet buffer. When
+ * '1', the received packet will be padded with 2B of zeros at the
+ * front of the packet. Note that this flag is only used for
+ * Rx rings and is ignored for all other rings included Rx
+ * Aggregation rings.
+ */
+ #define HWRM_RING_ALLOC_INPUT_FLAGS_RX_SOP_PAD UINT32_C(0x1)
+ /*
+ * This value is a pointer to the page table for the
+ * Ring.
+ */
+ uint64_t page_tbl_addr;
+ /* First Byte Offset of the first entry in the first page. */
+ uint32_t fbo;
+ /*
+ * Actual page size in 2^page_size. The supported range is increments
+ * in powers of 2 from 16 bytes to 1GB.
+ * - 4 = 16 B
+ * Page size is 16 B.
+ * - 12 = 4 KB
+ * Page size is 4 KB.
+ * - 13 = 8 KB
+ * Page size is 8 KB.
+ * - 16 = 64 KB
+ * Page size is 64 KB.
+ * - 21 = 2 MB
+ * Page size is 2 MB.
+ * - 22 = 4 MB
+ * Page size is 4 MB.
+ * - 30 = 1 GB
+ * Page size is 1 GB.
+ */
+ uint8_t page_size;
+ /*
+ * This value indicates the depth of page table.
+ * For this version of the specification, value other than 0 or
+ * 1 shall be considered as an invalid value.
+ * When the page_tbl_depth = 0, then it is treated as a
+ * special case with the following.
+ * 1. FBO and page size fields are not valid.
+ * 2. page_tbl_addr is the physical address of the first
+ * element of the ring.
+ */
+ uint8_t page_tbl_depth;
+ /* Used by a PF driver to associate a SCHQ with one of its TX rings. */
+ uint16_t schq_id;
+ /*
+ * Number of 16B units in the ring. Minimum size for
+ * a ring is 16 16B entries.
+ */
+ uint32_t length;
+ /*
+ * Logical ring number for the ring to be allocated.
+ * This value determines the position in the doorbell
+ * area where the update to the ring will be made.
+ *
+ * For completion rings, this value is also the MSI-X
+ * vector number for the function the completion ring is
+ * associated with.
+ */
+ uint16_t logical_id;
+ /*
+ * This field is used only when ring_type is a TX ring.
+ * This value indicates what completion ring the TX ring
+ * is associated with.
+ */
+ uint16_t cmpl_ring_id;
+ /*
+ * This field is used only when ring_type is a TX ring.
+ * This value indicates what CoS queue the TX ring
+ * is associated with.
+ */
+ uint16_t queue_id;
+ /*
+ * When allocating a Rx ring or Rx aggregation ring, this field
+ * specifies the size of the buffer descriptors posted to the ring.
+ */
+ uint16_t rx_buf_size;
+ /*
+ * When allocating an Rx aggregation ring, this field
+ * specifies the associated Rx ring ID.
+ */
+ uint16_t rx_ring_id;
+ /*
+ * When allocating a completion ring, this field
+ * specifies the associated NQ ring ID.
+ */
+ uint16_t nq_ring_id;
+ /*
+ * This field is used only when ring_type is a TX ring.
+ * This field is used to configure arbitration related
+ * parameters for a TX ring.
+ */
+ uint16_t ring_arb_cfg;
+ /* Arbitration policy used for the ring. */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SFT 0
+ /*
+ * Use strict priority for the TX ring.
+ * Priority value is specified in arb_policy_param
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SP \
+ UINT32_C(0x1)
+ /*
+ * Use weighted fair queue arbitration for the TX ring.
+ * Weight is specified in arb_policy_param
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ \
+ UINT32_C(0x2)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_LAST \
+ HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ
+ /* Reserved field. */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_SFT 4
+ /*
+ * Arbitration policy specific parameter.
+ * # For strict priority arbitration policy, this field
+ * represents a priority value. If set to 0, then the priority
+ * is not specified and the HWRM is allowed to select
+ * any priority for this TX ring.
+ * # For weighted fair queue arbitration policy, this field
+ * represents a weight value. If set to 0, then the weight
+ * is not specified and the HWRM is allowed to select
+ * any weight for this TX ring.
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_MASK \
+ UINT32_C(0xff00)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_SFT 8
+ uint16_t unused_3;
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint32_t reserved3;
+ /*
+ * This field is used only when ring_type is a TX ring.
+ * This input indicates what statistics context this ring
+ * should be associated with.
+ */
+ uint32_t stat_ctx_id;
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint32_t reserved4;
+ /*
+ * This field is used only when ring_type is a TX ring
+ * to specify maximum BW allocated to the TX ring.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this ring inside the device.
+ */
+ uint32_t max_bw;
+ /* The bandwidth value. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_LAST \
+ HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * This field is used only when ring_type is a Completion ring.
+ * This value indicates what interrupt mode should be used
+ * on this completion ring.
+ * Note: In the legacy interrupt mode, no more than 16
+ * completion rings are allowed.
+ */
+ uint8_t int_mode;
+ /* Legacy INTA */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY UINT32_C(0x0)
+ /* Reserved */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD UINT32_C(0x1)
+ /* MSI-X */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX UINT32_C(0x2)
+ /* No Interrupt - Polled mode */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL UINT32_C(0x3)
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_LAST \
+ HWRM_RING_ALLOC_INPUT_INT_MODE_POLL
+ /* Midpath channel type */
+ uint8_t mpc_chnls_type;
+ /*
+ * Indicate the TX ring alloc MPC channel type is a MPC channel
+ * with destination to the TX crypto engine block.
+ */
+ #define HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_TCE UINT32_C(0x0)
+ /*
+ * Indicate the RX ring alloc MPC channel type is a MPC channel
+ * with destination to the RX crypto engine block.
+ */
+ #define HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_RCE UINT32_C(0x1)
+ /*
+ * Indicate the RX ring alloc MPC channel type is a MPC channel
+ * with destination to the TX configurable flow processing block.
+ */
+ #define HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_TE_CFA UINT32_C(0x2)
+ /*
+ * Indicate the RX ring alloc MPC channel type is a MPC channel
+ * with destination to the RX configurable flow processing block.
+ */
+ #define HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_RE_CFA UINT32_C(0x3)
+ /*
+ * Indicate the RX ring alloc MPC channel type is a MPC channel
+ * with destination to the primate processor block.
+ */
+ #define HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_PRIMATE UINT32_C(0x4)
+ #define HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_LAST \
+ HWRM_RING_ALLOC_INPUT_MPC_CHNLS_TYPE_PRIMATE
+ uint8_t unused_4[2];
+ /*
+ * The cq_handle is specified when allocating a completion ring. For
+ * devices that support NQs, this cq_handle will be included in the
+ * NQE to specify which CQ should be read to retrieve the completion
+ * record.
+ */
+ uint64_t cq_handle;
+} __rte_packed;
+
+/* hwrm_ring_alloc_output (size:128b/16B) */
+struct hwrm_ring_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * Physical number of ring allocated.
+ * This value shall be unique for a ring type.
+ */
+ uint16_t ring_id;
+ /* Logical number of ring allocated. */
+ uint16_t logical_ring_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************
+ * hwrm_ring_free *
+ ******************/
+
+
+/* hwrm_ring_free_input (size:192b/24B) */
+struct hwrm_ring_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Ring Type. */
+ uint8_t ring_type;
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
+ /* RX Aggregation Ring */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_RX_AGG UINT32_C(0x4)
+ /* Notification Queue */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_NQ UINT32_C(0x5)
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_LAST \
+ HWRM_RING_FREE_INPUT_RING_TYPE_NQ
+ uint8_t unused_0;
+ /* Physical number of ring allocated. */
+ uint16_t ring_id;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_ring_free_output (size:128b/16B) */
+struct hwrm_ring_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************
+ * hwrm_ring_reset *
+ *******************/
+
+
+/* hwrm_ring_reset_input (size:192b/24B) */
+struct hwrm_ring_reset_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Ring Type. */
+ uint8_t ring_type;
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
+ /*
+ * Rx Ring Group. This is to reset rx and aggregation in an atomic
+ * operation. Completion ring associated with this ring group is
+ * not reset.
+ */
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_RX_RING_GRP UINT32_C(0x6)
+ #define HWRM_RING_RESET_INPUT_RING_TYPE_LAST \
+ HWRM_RING_RESET_INPUT_RING_TYPE_RX_RING_GRP
+ uint8_t unused_0;
+ /*
+ * Physical number of the ring. When ring type is rx_ring_grp, ring id
+ * actually refers to ring group id.
+ */
+ uint16_t ring_id;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_ring_reset_output (size:128b/16B) */
+struct hwrm_ring_reset_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[4];
+ /* Position of consumer index after ring reset completes. */
+ uint8_t consumer_idx[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*****************
+ * hwrm_ring_cfg *
+ *****************/
+
+
+/* hwrm_ring_cfg_input (size:256b/32B) */
+struct hwrm_ring_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Ring Type. */
+ uint8_t ring_type;
+ /* TX Ring (TR) */
+ #define HWRM_RING_CFG_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_CFG_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ #define HWRM_RING_CFG_INPUT_RING_TYPE_LAST \
+ HWRM_RING_CFG_INPUT_RING_TYPE_RX
+ uint8_t unused_0;
+ /* Physical number of the ring. */
+ uint16_t ring_id;
+ /* Ring config enable bits. */
+ uint16_t enables;
+ /*
+ * For Rx rings, the incoming packet data can be placed at either
+ * a 0B, 2B, 10B or 12B offset from the start of the Rx packet
+ * buffer.
+ * When '1', the received packet will be padded with 2B, 10B or 12B
+ * of zeros at the front of the packet. The exact offset is specified
+ * by rx_sop_pad_bytes parameter.
+ * When '0', the received packet will not be padded.
+ * Note that this flag is only used for Rx rings and is ignored
+ * for all other rings included Rx Aggregation rings.
+ */
+ #define HWRM_RING_CFG_INPUT_ENABLES_RX_SOP_PAD_ENABLE \
+ UINT32_C(0x1)
+ /*
+ * Proxy mode enable, for Tx, Rx and Rx aggregation rings only.
+ * When rings are allocated, the PCI function on which driver issues
+ * HWRM_RING_CFG command is assumed to own the rings. Hardware takes
+ * the buffer descriptors (BDs) from those rings is assumed to issue
+ * packet payload DMA using same PCI function. When proxy mode is
+ * enabled, hardware can perform payload DMA using another PCI
+ * function on same or different host.
+ * When set to '0', the PCI function on which driver issues
+ * HWRM_RING_CFG command is used for host payload DMA operation.
+ * When set to '1', the host PCI function specified by proxy_fid is
+ * used for host payload DMA operation.
+ */
+ #define HWRM_RING_CFG_INPUT_ENABLES_PROXY_MODE_ENABLE \
+ UINT32_C(0x2)
+ /*
+ * Tx ring packet source interface override, for Tx rings only.
+ * When TX rings are allocated, the PCI function on which driver
+ * issues HWRM_RING_CFG is assumed to be source interface of
+ * packets sent from TX ring.
+ * When set to '1', the host PCI function specified by proxy_fid
+ * is used as source interface of the transmitted packets.
+ */
+ #define HWRM_RING_CFG_INPUT_ENABLES_TX_PROXY_SRC_INTF_OVERRIDE \
+ UINT32_C(0x4)
+ /* The schq_id field is valid */
+ #define HWRM_RING_CFG_INPUT_ENABLES_SCHQ_ID \
+ UINT32_C(0x8)
+ /* Update completion ring ID associated with Tx or Rx ring. */
+ #define HWRM_RING_CFG_INPUT_ENABLES_CMPL_RING_ID_UPDATE \
+ UINT32_C(0x10)
+ /*
+ * Proxy function FID value.
+ * This value is only used when either proxy_mode_enable flag or
+ * tx_proxy_svif_override is set to '1'.
+ * When proxy_mode_enable is set to '1', it identifies a host PCI
+ * function used for host payload DMA operations.
+ * When tx_proxy_src_intf is set to '1', it identifies a host PCI
+ * function as source interface for all transmitted packets from
+ * the TX ring.
+ */
+ uint16_t proxy_fid;
+ /*
+ * Identifies the new scheduler queue (SCHQ) to associate with the
+ * ring. Only valid for Tx rings.
+ * A value of zero indicates that the Tx ring should be associated
+ * with the default scheduler queue (SCHQ).
+ */
+ uint16_t schq_id;
+ /*
+ * This field is valid for TX or Rx rings. This value identifies the
+ * new completion ring ID to associate with the TX or Rx ring.
+ */
+ uint16_t cmpl_ring_id;
+ /*
+ * Rx SOP padding amount in bytes.
+ * This value is only used when rx_sop_pad_enable flag is set to '1'.
+ */
+ uint8_t rx_sop_pad_bytes;
+ uint8_t unused_1[3];
+} __rte_packed;
+
+/* hwrm_ring_cfg_output (size:128b/16B) */
+struct hwrm_ring_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
+ * processor, the order of writes has to be such that this field is
+ * written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************
+ * hwrm_ring_qcfg *
+ ******************/
+
+
+/* hwrm_ring_qcfg_input (size:192b/24B) */
+struct hwrm_ring_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Ring Type. */
+ uint8_t ring_type;
+ /* TX Ring (TR) */
+ #define HWRM_RING_QCFG_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_QCFG_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ #define HWRM_RING_QCFG_INPUT_RING_TYPE_LAST \
+ HWRM_RING_QCFG_INPUT_RING_TYPE_RX
+ uint8_t unused_0[5];
+ /* Physical number of the ring. */
+ uint16_t ring_id;
+} __rte_packed;
+
+/* hwrm_ring_qcfg_output (size:192b/24B) */
+struct hwrm_ring_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Ring config enable bits. */
+ uint16_t enables;
+ /*
+ * For Rx rings, the incoming packet data can be placed at either
+ * a 0B, 2B, 10B or 12B offset from the start of the Rx packet
+ * buffer.
+ * When '1', the received packet will be padded with 2B, 10B or 12B
+ * of zeros at the front of the packet. The exact offset is specified
+ * by rx_sop_pad_bytes parameter.
+ * When '0', the received packet will not be padded.
+ * Note that this flag is only used for Rx rings and is ignored
+ * for all other rings included Rx Aggregation rings.
+ */
+ #define HWRM_RING_QCFG_OUTPUT_ENABLES_RX_SOP_PAD_ENABLE \
+ UINT32_C(0x1)
+ /*
+ * Proxy mode enable, for Tx, Rx and Rx aggregation rings only.
+ * When rings are allocated, the PCI function on which driver issues
+ * HWRM_RING_CFG command is assumed to own the rings. Hardware takes
+ * the buffer descriptors (BDs) from those rings is assumed to issue
+ * packet payload DMA using same PCI function. When proxy mode is
+ * enabled, hardware can perform payload DMA using another PCI
+ * function on same or different host.
+ * When set to '0', the PCI function on which driver issues
+ * HWRM_RING_CFG command is used for host payload DMA operation.
+ * When set to '1', the host PCI function specified by proxy_fid is
+ * used for host payload DMA operation.
+ */
+ #define HWRM_RING_QCFG_OUTPUT_ENABLES_PROXY_MODE_ENABLE \
+ UINT32_C(0x2)
+ /*
+ * Tx ring packet source interface override, for Tx rings only.
+ * When TX rings are allocated, the PCI function on which driver
+ * issues HWRM_RING_CFG is assumed to be source interface of
+ * packets sent from TX ring.
+ * When set to '1', the host PCI function specified by proxy_fid is
+ * used as source interface of the transmitted packets.
+ */
+ #define HWRM_RING_QCFG_OUTPUT_ENABLES_TX_PROXY_SRC_INTF_OVERRIDE \
+ UINT32_C(0x4)
+ /*
+ * Proxy function FID value.
+ * This value is only used when either proxy_mode_enable flag or
+ * tx_proxy_svif_override is set to '1'.
+ * When proxy_mode_enable is set to '1', it identifies a host PCI
+ * function used for host payload DMA operations.
+ * When tx_proxy_src_intf is set to '1', it identifies a host PCI
+ * function as source interface for all transmitted packets from the TX
+ * ring.
+ */
+ uint16_t proxy_fid;
+ /*
+ * Identifies the new scheduler queue (SCHQ) to associate with the
+ * ring. Only valid for Tx rings.
+ * A value of zero indicates that the Tx ring should be associated with
+ * the default scheduler queue (SCHQ).
+ */
+ uint16_t schq_id;
+ /*
+ * This field is used when ring_type is a TX or Rx ring.
+ * This value indicates what completion ring the TX or Rx ring
+ * is associated with.
+ */
+ uint16_t cmpl_ring_id;
+ /*
+ * Rx SOP padding amount in bytes.
+ * This value is only used when rx_sop_pad_enable flag is set to '1'.
+ */
+ uint8_t rx_sop_pad_bytes;
+ uint8_t unused_0[6];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
+ * processor, the order of writes has to be such that this field is
+ * written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_ring_aggint_qcaps *
+ **************************/
+
+
+/* hwrm_ring_aggint_qcaps_input (size:128b/16B) */
+struct hwrm_ring_aggint_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_ring_aggint_qcaps_output (size:384b/48B) */
+struct hwrm_ring_aggint_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t cmpl_params;
+ /*
+ * When this bit is set to '1', int_lat_tmr_min can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_INT_LAT_TMR_MIN \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', int_lat_tmr_max can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_INT_LAT_TMR_MAX \
+ UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', timer_reset can be enabled
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_TIMER_RESET \
+ UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', ring_idle can be enabled
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_RING_IDLE \
+ UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', num_cmpl_dma_aggr can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_NUM_CMPL_DMA_AGGR \
+ UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', num_cmpl_dma_aggr_during_int can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_NUM_CMPL_DMA_AGGR_DURING_INT \
+ UINT32_C(0x20)
+ /*
+ * When this bit is set to '1', cmpl_aggr_dma_tmr can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_CMPL_AGGR_DMA_TMR \
+ UINT32_C(0x40)
+ /*
+ * When this bit is set to '1', cmpl_aggr_dma_tmr_during_int can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_CMPL_AGGR_DMA_TMR_DURING_INT \
+ UINT32_C(0x80)
+ /*
+ * When this bit is set to '1', num_cmpl_aggr_int can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_NUM_CMPL_AGGR_INT \
+ UINT32_C(0x100)
+ uint32_t nq_params;
+ /*
+ * When this bit is set to '1', int_lat_tmr_min can be configured
+ * on notification queues.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_NQ_PARAMS_INT_LAT_TMR_MIN \
+ UINT32_C(0x1)
+ /* Minimum value for num_cmpl_dma_aggr */
+ uint16_t num_cmpl_dma_aggr_min;
+ /* Maximum value for num_cmpl_dma_aggr */
+ uint16_t num_cmpl_dma_aggr_max;
+ /* Minimum value for num_cmpl_dma_aggr_during_int */
+ uint16_t num_cmpl_dma_aggr_during_int_min;
+ /* Maximum value for num_cmpl_dma_aggr_during_int */
+ uint16_t num_cmpl_dma_aggr_during_int_max;
+ /* Minimum value for cmpl_aggr_dma_tmr */
+ uint16_t cmpl_aggr_dma_tmr_min;
+ /* Maximum value for cmpl_aggr_dma_tmr */
+ uint16_t cmpl_aggr_dma_tmr_max;
+ /* Minimum value for cmpl_aggr_dma_tmr_during_int */
+ uint16_t cmpl_aggr_dma_tmr_during_int_min;
+ /* Maximum value for cmpl_aggr_dma_tmr_during_int */
+ uint16_t cmpl_aggr_dma_tmr_during_int_max;
+ /* Minimum value for int_lat_tmr_min */
+ uint16_t int_lat_tmr_min_min;
+ /* Maximum value for int_lat_tmr_min */
+ uint16_t int_lat_tmr_min_max;
+ /* Minimum value for int_lat_tmr_max */
+ uint16_t int_lat_tmr_max_min;
+ /* Maximum value for int_lat_tmr_max */
+ uint16_t int_lat_tmr_max_max;
+ /* Minimum value for num_cmpl_aggr_int */
+ uint16_t num_cmpl_aggr_int_min;
+ /* Maximum value for num_cmpl_aggr_int */
+ uint16_t num_cmpl_aggr_int_max;
+ /* The units for timer parameters, in nanoseconds. */
+ uint16_t timer_units;
+ uint8_t unused_0[1];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************************
+ * hwrm_ring_cmpl_ring_qaggint_params *
+ **************************************/
+
+
+/* hwrm_ring_cmpl_ring_qaggint_params_input (size:192b/24B) */
+struct hwrm_ring_cmpl_ring_qaggint_params_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Physical number of completion ring. */
+ uint16_t ring_id;
+ uint16_t flags;
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_INPUT_FLAGS_UNUSED_0_MASK \
+ UINT32_C(0x3)
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_INPUT_FLAGS_UNUSED_0_SFT 0
+ /*
+ * Set this flag to 1 when querying parameters on a notification
+ * queue. Set this flag to 0 when querying parameters on a
+ * completion queue or completion ring.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_INPUT_FLAGS_IS_NQ \
+ UINT32_C(0x4)
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_ring_cmpl_ring_qaggint_params_output (size:256b/32B) */
+struct hwrm_ring_cmpl_ring_qaggint_params_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint16_t flags;
+ /*
+ * When this bit is set to '1', interrupt max
+ * timer is reset whenever a completion is received.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_TIMER_RESET \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', ring idle mode
+ * aggregation will be enabled.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_RING_IDLE \
+ UINT32_C(0x2)
+ /*
+ * Number of completions to aggregate before DMA
+ * during the normal mode.
+ */
+ uint16_t num_cmpl_dma_aggr;
+ /*
+ * Number of completions to aggregate before DMA
+ * during the interrupt mode.
+ */
+ uint16_t num_cmpl_dma_aggr_during_int;
+ /*
+ * Timer used to aggregate completions before
+ * DMA during the normal mode (not in interrupt mode).
+ */
+ uint16_t cmpl_aggr_dma_tmr;
+ /*
+ * Timer used to aggregate completions before
+ * DMA when in interrupt mode.
+ */
+ uint16_t cmpl_aggr_dma_tmr_during_int;
+ /* Minimum time between two interrupts. */
+ uint16_t int_lat_tmr_min;
+ /*
+ * Maximum wait time spent aggregating
+ * completions before signaling the interrupt after the
+ * interrupt is enabled.
+ */
+ uint16_t int_lat_tmr_max;
+ /*
+ * Minimum number of completions aggregated before signaling
+ * an interrupt.
+ */
+ uint16_t num_cmpl_aggr_int;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*****************************************
+ * hwrm_ring_cmpl_ring_cfg_aggint_params *
+ *****************************************/
+
+
+/* hwrm_ring_cmpl_ring_cfg_aggint_params_input (size:320b/40B) */
+struct hwrm_ring_cmpl_ring_cfg_aggint_params_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Physical number of completion ring. */
+ uint16_t ring_id;
+ uint16_t flags;
+ /*
+ * When this bit is set to '1', interrupt latency max
+ * timer is reset whenever a completion is received.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_TIMER_RESET \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', ring idle mode
+ * aggregation will be enabled.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_RING_IDLE \
+ UINT32_C(0x2)
+ /*
+ * Set this flag to 1 when configuring parameters on a
+ * notification queue. Set this flag to 0 when configuring
+ * parameters on a completion queue or completion ring.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_FLAGS_IS_NQ \
+ UINT32_C(0x4)
+ /*
+ * Number of completions to aggregate before DMA
+ * during the normal mode.
+ */
+ uint16_t num_cmpl_dma_aggr;
+ /*
+ * Number of completions to aggregate before DMA
+ * during the interrupt mode.
+ */
+ uint16_t num_cmpl_dma_aggr_during_int;
+ /*
+ * Timer used to aggregate completions before
+ * DMA during the normal mode (not in interrupt mode).
+ */
+ uint16_t cmpl_aggr_dma_tmr;
+ /*
+ * Timer used to aggregate completions before
+ * DMA while in interrupt mode.
+ */
+ uint16_t cmpl_aggr_dma_tmr_during_int;
+ /* Minimum time between two interrupts. */
+ uint16_t int_lat_tmr_min;
+ /*
+ * Maximum wait time spent aggregating
+ * completions before signaling the interrupt after the
+ * interrupt is enabled.
+ */
+ uint16_t int_lat_tmr_max;
+ /*
+ * Minimum number of completions aggregated before signaling
+ * an interrupt.
+ */
+ uint16_t num_cmpl_aggr_int;
+ /*
+ * Bitfield that indicates which parameters are to be applied. Only
+ * required when configuring devices with notification queues, and
+ * used in that case to set certain parameters on completion queues
+ * and others on notification queues.
+ */
+ uint16_t enables;
+ /*
+ * This bit must be '1' for the num_cmpl_dma_aggr field to be
+ * configured.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_NUM_CMPL_DMA_AGGR \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the num_cmpl_dma_aggr_during_int field to be
+ * configured.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_NUM_CMPL_DMA_AGGR_DURING_INT \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the cmpl_aggr_dma_tmr field to be
+ * configured.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_CMPL_AGGR_DMA_TMR \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the int_lat_tmr_min field to be
+ * configured.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_INT_LAT_TMR_MIN \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the int_lat_tmr_max field to be
+ * configured.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_INT_LAT_TMR_MAX \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the num_cmpl_aggr_int field to be
+ * configured.
+ */
+ #define HWRM_RING_CMPL_RING_CFG_AGGINT_PARAMS_INPUT_ENABLES_NUM_CMPL_AGGR_INT \
+ UINT32_C(0x20)
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_ring_cmpl_ring_cfg_aggint_params_output (size:128b/16B) */
+struct hwrm_ring_cmpl_ring_cfg_aggint_params_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_ring_grp_alloc *
+ ***********************/
+
+
+/* hwrm_ring_grp_alloc_input (size:192b/24B) */
+struct hwrm_ring_grp_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * This value identifies the CR associated with the ring
+ * group.
+ */
+ uint16_t cr;
+ /*
+ * This value identifies the main RR associated with the ring
+ * group.
+ */
+ uint16_t rr;
+ /*
+ * This value identifies the aggregation RR associated with
+ * the ring group. If this value is 0xFF... (All Fs), then no
+ * Aggregation ring will be set.
+ */
+ uint16_t ar;
+ /*
+ * This value identifies the statistics context associated
+ * with the ring group.
+ */
+ uint16_t sc;
+} __rte_packed;
+
+/* hwrm_ring_grp_alloc_output (size:128b/16B) */
+struct hwrm_ring_grp_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * This is the ring group ID value. Use this value to program
+ * the default ring group for the VNIC or as table entries
+ * in an RSS/COS context.
+ */
+ uint32_t ring_group_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_ring_grp_free *
+ **********************/
+
+
+/* hwrm_ring_grp_free_input (size:192b/24B) */
+struct hwrm_ring_grp_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This is the ring group ID value. */
+ uint32_t ring_group_id;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_ring_grp_free_output (size:128b/16B) */
+struct hwrm_ring_grp_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/************************
+ * hwrm_ring_schq_alloc *
+ ************************/
+
+
+/* hwrm_ring_schq_alloc_input (size:1088b/136B) */
+struct hwrm_ring_schq_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the tqm_ring0 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING0 UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the tqm_ring1 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING1 UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the tqm_ring2 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING2 UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the tqm_ring3 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING3 UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the tqm_ring4 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING4 UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the tqm_ring5 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING5 UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the tqm_ring6 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING6 UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the tqm_ring7 fields to be
+ * configured.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_ENABLES_TQM_RING7 UINT32_C(0x80)
+ /* Reserved for future use. */
+ uint32_t reserved;
+ /* TQM ring 0 page size and level. */
+ uint8_t tqm_ring0_pg_size_tqm_ring0_lvl;
+ /* TQM ring 0 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_LVL_LVL_2
+ /* TQM ring 0 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING0_PG_SIZE_PG_1G
+ /* TQM ring 1 page size and level. */
+ uint8_t tqm_ring1_pg_size_tqm_ring1_lvl;
+ /* TQM ring 1 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_LVL_LVL_2
+ /* TQM ring 1 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING1_PG_SIZE_PG_1G
+ /* TQM ring 2 page size and level. */
+ uint8_t tqm_ring2_pg_size_tqm_ring2_lvl;
+ /* TQM ring 2 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_LVL_LVL_2
+ /* TQM ring 2 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING2_PG_SIZE_PG_1G
+ /* TQM ring 3 page size and level. */
+ uint8_t tqm_ring3_pg_size_tqm_ring3_lvl;
+ /* TQM ring 3 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_LVL_LVL_2
+ /* TQM ring 3 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING3_PG_SIZE_PG_1G
+ /* TQM ring 4 page size and level. */
+ uint8_t tqm_ring4_pg_size_tqm_ring4_lvl;
+ /* TQM ring 4 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_LVL_LVL_2
+ /* TQM ring 4 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING4_PG_SIZE_PG_1G
+ /* TQM ring 5 page size and level. */
+ uint8_t tqm_ring5_pg_size_tqm_ring5_lvl;
+ /* TQM ring 5 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_LVL_LVL_2
+ /* TQM ring 5 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING5_PG_SIZE_PG_1G
+ /* TQM ring 6 page size and level. */
+ uint8_t tqm_ring6_pg_size_tqm_ring6_lvl;
+ /* TQM ring 6 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_LVL_LVL_2
+ /* TQM ring 6 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING6_PG_SIZE_PG_1G
+ /* TQM ring 7 page size and level. */
+ uint8_t tqm_ring7_pg_size_tqm_ring7_lvl;
+ /* TQM ring 7 PBL indirect levels. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_MASK \
+ UINT32_C(0xf)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_SFT 0
+ /* PBL pointer is physical start address. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_LVL_0 \
+ UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_LVL_1 \
+ UINT32_C(0x1)
+ /*
+ * PBL pointer points to PDE table with each entry pointing to PTE
+ * tables.
+ */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_LVL_2 \
+ UINT32_C(0x2)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_LVL_LVL_2
+ /* TQM ring 7 page size. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_MASK \
+ UINT32_C(0xf0)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_SFT 4
+ /* 4KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_4K \
+ (UINT32_C(0x0) << 4)
+ /* 8KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_8K \
+ (UINT32_C(0x1) << 4)
+ /* 64KB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_64K \
+ (UINT32_C(0x2) << 4)
+ /* 2MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_2M \
+ (UINT32_C(0x3) << 4)
+ /* 8MB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_8M \
+ (UINT32_C(0x4) << 4)
+ /* 1GB. */
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_1G \
+ (UINT32_C(0x5) << 4)
+ #define HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_LAST \
+ HWRM_RING_SCHQ_ALLOC_INPUT_TQM_RING7_PG_SIZE_PG_1G
+ /* TQM ring 0 page directory. */
+ uint64_t tqm_ring0_page_dir;
+ /* TQM ring 1 page directory. */
+ uint64_t tqm_ring1_page_dir;
+ /* TQM ring 2 page directory. */
+ uint64_t tqm_ring2_page_dir;
+ /* TQM ring 3 page directory. */
+ uint64_t tqm_ring3_page_dir;
+ /* TQM ring 4 page directory. */
+ uint64_t tqm_ring4_page_dir;
+ /* TQM ring 5 page directory. */
+ uint64_t tqm_ring5_page_dir;
+ /* TQM ring 6 page directory. */
+ uint64_t tqm_ring6_page_dir;
+ /* TQM ring 7 page directory. */
+ uint64_t tqm_ring7_page_dir;
+ /*
+ * Number of TQM ring 0 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring0_num_entries;
+ /*
+ * Number of TQM ring 1 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring1_num_entries;
+ /*
+ * Number of TQM ring 2 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring2_num_entries;
+ /*
+ * Number of TQM ring 3 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring3_num_entries;
+ /*
+ * Number of TQM ring 4 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring4_num_entries;
+ /*
+ * Number of TQM ring 5 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring5_num_entries;
+ /*
+ * Number of TQM ring 6 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring6_num_entries;
+ /*
+ * Number of TQM ring 7 entries.
+ *
+ * TQM fastpath rings should be sized large enough to accommodate the
+ * maximum number of QPs (either L2 or RoCE, or both if shared)
+ * that can be enqueued to the TQM ring.
+ *
+ * Note that TQM ring sizes cannot be extended while the system is
+ * operational. If a PF driver needs to extend a TQM ring, it needs
+ * to delete the SCHQ and then reallocate it.
+ */
+ uint32_t tqm_ring7_num_entries;
+ /* Number of bytes that have been allocated for each context entry. */
+ uint16_t tqm_entry_size;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_ring_schq_alloc_output (size:128b/16B) */
+struct hwrm_ring_schq_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * This is an identifier for the SCHQ to be used in other HWRM commands
+ * that need to reference this SCHQ. This value is greater than zero
+ * (i.e. a schq_id of zero references the default SCHQ).
+ */
+ uint16_t schq_id;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_ring_schq_cfg *
+ **********************/
+
+
+/* hwrm_ring_schq_cfg_input (size:768b/96B) */
+struct hwrm_ring_schq_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Identifies the SCHQ being configured. A schq_id of zero refers to
+ * the default SCHQ.
+ */
+ uint16_t schq_id;
+ /*
+ * This field is an 8 bit bitmap that indicates which TCs are enabled
+ * in this SCHQ. Bit 0 represents traffic class 0 and bit 7 represents
+ * traffic class 7.
+ */
+ uint8_t tc_enabled;
+ uint8_t unused_0;
+ uint32_t flags;
+ /* The tc_max_bw array and the max_bw parameters are valid */
+ #define HWRM_RING_SCHQ_CFG_INPUT_FLAGS_TC_MAX_BW_ENABLED \
+ UINT32_C(0x1)
+ /* The tc_min_bw array is valid */
+ #define HWRM_RING_SCHQ_CFG_INPUT_FLAGS_TC_MIN_BW_ENABLED \
+ UINT32_C(0x2)
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc0;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc1;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc2;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc3;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc4;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc5;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc6;
+ /* Maximum bandwidth of the traffic class, specified in Mbps. */
+ uint32_t max_bw_tc7;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc0;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc1;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc2;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc3;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc4;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc5;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc6;
+ /*
+ * Bandwidth reservation for the traffic class, specified in Mbps.
+ * A value of zero signifies that traffic belonging to this class
+ * shares the bandwidth reservation for the same traffic class of
+ * the default SCHQ.
+ */
+ uint32_t min_bw_tc7;
+ /*
+ * Indicates the max bandwidth for all enabled traffic classes in
+ * this SCHQ, specified in Mbps.
+ */
+ uint32_t max_bw;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_ring_schq_cfg_output (size:128b/16B) */
+struct hwrm_ring_schq_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_ring_schq_free *
+ ***********************/
+
+
+/* hwrm_ring_schq_free_input (size:192b/24B) */
+struct hwrm_ring_schq_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Identifies the SCHQ being freed. */
+ uint16_t schq_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_ring_schq_free_output (size:128b/16B) */
+struct hwrm_ring_schq_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+/*
+ * special reserved flow ID to identify per function default
+ * flows for vSwitch offload
+ */
+#define DEFAULT_FLOW_ID 0xFFFFFFFFUL
+/*
+ * special reserved flow ID to identify per function RoCEv1
+ * flows
+ */
+#define ROCEV1_FLOW_ID 0xFFFFFFFEUL
+/*
+ * special reserved flow ID to identify per function RoCEv2
+ * flows
+ */
+#define ROCEV2_FLOW_ID 0xFFFFFFFDUL
+/*
+ * special reserved flow ID to identify per function RoCEv2
+ * CNP flows
+ */
+#define ROCEV2_CNP_FLOW_ID 0xFFFFFFFCUL
+
+/****************************
+ * hwrm_cfa_l2_filter_alloc *
+ ****************************/
+
+
+/* hwrm_cfa_l2_filter_alloc_input (size:768b/96B) */
+struct hwrm_cfa_l2_filter_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH \
+ UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX
+ /* Setting of this flag indicates the applicability to the loopback path. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP \
+ UINT32_C(0x4)
+ /*
+ * If this flag is set, all t_l2_* fields are invalid
+ * and they should not be specified.
+ * If this flag is set, then l2_* fields refer to
+ * fields of outermost L2 header.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST \
+ UINT32_C(0x8)
+ /*
+ * Enumeration denoting NO_ROCE_L2 to support old drivers.
+ * New driver L2 for only L2 traffic, ROCE for roce and l2 traffic
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_MASK \
+ UINT32_C(0x30)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_SFT 4
+ /* To support old drivers */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_NO_ROCE_L2 \
+ (UINT32_C(0x0) << 4)
+ /* Only L2 traffic */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_L2 \
+ (UINT32_C(0x1) << 4)
+ /* Roce & L2 traffic */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_ROCE \
+ (UINT32_C(0x2) << 4)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_TRAFFIC_ROCE
+ /*
+ * Setting of this flag indicates that no XDP filter is created with
+ * L2 filter.
+ * 0 - legacy behavior, XDP filter is created with L2 filter
+ * 1 - XDP filter won't be created with L2 filter
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_XDP_DISABLE \
+ UINT32_C(0x40)
+ /*
+ * Setting this flag to 1 indicate the L2 fields in this command
+ * pertain to source fields. Setting this flag to 0 indicate the
+ * L2 fields in this command pertain to the destination fields
+ * and this is the default/legacy behavior.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_SOURCE_VALID \
+ UINT32_C(0x80)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the l2_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the l2_addr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the l2_ovlan field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the l2_ovlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the l2_ivlan field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the l2_ivlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the t_l2_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the t_l2_addr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the t_l2_ovlan field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the t_l2_ovlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the t_l2_ivlan field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the t_l2_ivlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK \
+ UINT32_C(0x800)
+ /*
+ * This bit must be '1' for the src_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE \
+ UINT32_C(0x1000)
+ /*
+ * This bit must be '1' for the src_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID \
+ UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the tunnel_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the dst_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the num_vlans field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_NUM_VLANS \
+ UINT32_C(0x20000)
+ /*
+ * This bit must be '1' for the t_num_vlans field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_NUM_VLANS \
+ UINT32_C(0x40000)
+ /*
+ * This value sets the match value for the L2 MAC address.
+ * Destination MAC address for RX path.
+ * Source MAC address for TX path.
+ */
+ uint8_t l2_addr[6];
+ /* This value sets the match value for the number of VLANs. */
+ uint8_t num_vlans;
+ /*
+ * This value sets the match value for the number of VLANs
+ * in the tunnel headers.
+ */
+ uint8_t t_num_vlans;
+ /*
+ * This value sets the mask value for the L2 address.
+ * A value of 0 will mask the corresponding bit from
+ * compare.
+ */
+ uint8_t l2_addr_mask[6];
+ /* This value sets VLAN ID value for outer VLAN. */
+ uint16_t l2_ovlan;
+ /*
+ * This value sets the mask value for the ovlan id.
+ * A value of 0 will mask the corresponding bit from
+ * compare.
+ */
+ uint16_t l2_ovlan_mask;
+ /* This value sets VLAN ID value for inner VLAN. */
+ uint16_t l2_ivlan;
+ /*
+ * This value sets the mask value for the ivlan id.
+ * A value of 0 will mask the corresponding bit from
+ * compare.
+ */
+ uint16_t l2_ivlan_mask;
+ uint8_t unused_1[2];
+ /*
+ * This value sets the match value for the tunnel
+ * L2 MAC address.
+ * Destination MAC address for RX path.
+ * Source MAC address for TX path.
+ */
+ uint8_t t_l2_addr[6];
+ uint8_t unused_2[2];
+ /*
+ * This value sets the mask value for the tunnel L2
+ * address.
+ * A value of 0 will mask the corresponding bit from
+ * compare.
+ */
+ uint8_t t_l2_addr_mask[6];
+ /* This value sets VLAN ID value for tunnel outer VLAN. */
+ uint16_t t_l2_ovlan;
+ /*
+ * This value sets the mask value for the tunnel ovlan id.
+ * A value of 0 will mask the corresponding bit from
+ * compare.
+ */
+ uint16_t t_l2_ovlan_mask;
+ /* This value sets VLAN ID value for tunnel inner VLAN. */
+ uint16_t t_l2_ivlan;
+ /*
+ * This value sets the mask value for the tunnel ivlan id.
+ * A value of 0 will mask the corresponding bit from
+ * compare.
+ */
+ uint16_t t_l2_ivlan_mask;
+ /* This value identifies the type of source of the packet. */
+ uint8_t src_type;
+ /* Network port */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT UINT32_C(0x0)
+ /* Physical function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF UINT32_C(0x1)
+ /* Virtual function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF UINT32_C(0x2)
+ /* Virtual NIC of a function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC UINT32_C(0x3)
+ /* Embedded processor for CFA management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG UINT32_C(0x4)
+ /* Embedded processor for OOB management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE UINT32_C(0x5)
+ /* Embedded processor for RoCE */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO UINT32_C(0x6)
+ /* Embedded processor for network proxy functions */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG UINT32_C(0x7)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG
+ uint8_t unused_3;
+ /*
+ * This value is the id of the source.
+ * For a network port, it represents port_id.
+ * For a physical function, it represents fid.
+ * For a virtual function, it represents vf_id.
+ * For a vnic, it represents vnic_id.
+ * For embedded processors, this id is not valid.
+ *
+ * Notes:
+ * 1. The function ID is implied if it src_id is
+ * not provided for a src_type that is either
+ */
+ uint32_t src_id;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_4;
+ /*
+ * If set, this value shall represent the
+ * Logical VNIC ID of the destination VNIC for the RX
+ * path and network port id of the destination port for
+ * the TX path.
+ */
+ uint16_t dst_id;
+ /*
+ * Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint16_t mirror_vnic_id;
+ /*
+ * This hint is provided to help in placing
+ * the filter in the filter table.
+ */
+ uint8_t pri_hint;
+ /* No preference */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
+ UINT32_C(0x0)
+ /* Above the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER \
+ UINT32_C(0x1)
+ /* Below the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER \
+ UINT32_C(0x2)
+ /* As high as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX \
+ UINT32_C(0x3)
+ /* As low as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN \
+ UINT32_C(0x4)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN
+ uint8_t unused_5;
+ uint32_t unused_6;
+ /*
+ * This is the ID of the filter that goes along with
+ * the pri_hint.
+ *
+ * This field is valid only for the following values.
+ * 1 - Above the given filter
+ * 2 - Below the given filter
+ */
+ uint64_t l2_filter_id_hint;
+} __rte_packed;
+
+/* hwrm_cfa_l2_filter_alloc_output (size:192b/24B) */
+struct hwrm_cfa_l2_filter_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * The flow id value in bit 0-29 is the actual ID of the flow
+ * associated with this filter and it shall be used to match
+ * and associate the flow identifier returned in completion
+ * records. A value of 0xFFFFFFFF in the 32-bit flow_id field
+ * shall indicate no valid flow id.
+ */
+ uint32_t flow_id;
+ /* Indicate the flow id value. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_VALUE_MASK \
+ UINT32_C(0x3fffffff)
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_VALUE_SFT 0
+ /* Indicate type of the flow. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE \
+ UINT32_C(0x40000000)
+ /*
+ * If this bit set to 0, then it indicates that the flow is
+ * internal flow.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_INT \
+ (UINT32_C(0x0) << 30)
+ /*
+ * If this bit is set to 1, then it indicates that the flow is
+ * external flow.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT \
+ (UINT32_C(0x1) << 30)
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT
+ /* Indicate the flow direction. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR \
+ UINT32_C(0x80000000)
+ /* If this bit set to 0, then it indicates rx flow. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_RX \
+ (UINT32_C(0x0) << 31)
+ /* If this bit is set to 1, then it indicates that tx flow. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_TX \
+ (UINT32_C(0x1) << 31)
+ #define HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_LAST \
+ HWRM_CFA_L2_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_TX
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_cfa_l2_filter_free *
+ ***************************/
+
+
+/* hwrm_cfa_l2_filter_free_input (size:192b/24B) */
+struct hwrm_cfa_l2_filter_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+} __rte_packed;
+
+/* hwrm_cfa_l2_filter_free_output (size:128b/16B) */
+struct hwrm_cfa_l2_filter_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_cfa_l2_filter_cfg *
+ **************************/
+
+
+/* hwrm_cfa_l2_filter_cfg_input (size:320b/40B) */
+struct hwrm_cfa_l2_filter_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH \
+ UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_DROP \
+ UINT32_C(0x2)
+ /*
+ * Enumeration denoting NO_ROCE_L2 to support old drivers.
+ * New driver L2 for only L2 traffic, ROCE for roce and l2 traffic
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_MASK \
+ UINT32_C(0xc)
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_SFT 2
+ /* To support old drivers */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_NO_ROCE_L2 \
+ (UINT32_C(0x0) << 2)
+ /* Only L2 traffic */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_L2 \
+ (UINT32_C(0x1) << 2)
+ /* Roce & L2 traffic */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_ROCE \
+ (UINT32_C(0x2) << 2)
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_LAST \
+ HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_TRAFFIC_ROCE
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the dst_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
+ UINT32_C(0x2)
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * If set, this value shall represent the
+ * Logical VNIC ID of the destination VNIC for the RX
+ * path and network port id of the destination port for
+ * the TX path.
+ */
+ uint32_t dst_id;
+ /*
+ * New Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint32_t new_mirror_vnic_id;
+} __rte_packed;
+
+/* hwrm_cfa_l2_filter_cfg_output (size:128b/16B) */
+struct hwrm_cfa_l2_filter_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_cfa_l2_set_rx_mask *
+ ***************************/
+
+
+/* hwrm_cfa_l2_set_rx_mask_input (size:448b/56B) */
+struct hwrm_cfa_l2_set_rx_mask_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* VNIC ID */
+ uint32_t vnic_id;
+ uint32_t mask;
+ /*
+ * When this bit is '1', the function is requested to accept
+ * multi-cast packets specified by the multicast addr table.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the function is requested to accept
+ * all multi-cast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the function is requested to accept
+ * broadcast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', the function is requested to be
+ * put in the promiscuous mode.
+ *
+ * The HWRM should accept any function to set up
+ * promiscuous mode.
+ *
+ * The HWRM shall follow the semantics below for the
+ * promiscuous mode support.
+ * # When partitioning is not enabled on a port
+ * (i.e. single PF on the port), then the PF shall
+ * be allowed to be in the promiscuous mode. When the
+ * PF is in the promiscuous mode, then it shall
+ * receive all host bound traffic on that port.
+ * # When partitioning is enabled on a port
+ * (i.e. multiple PFs per port) and a PF on that
+ * port is in the promiscuous mode, then the PF
+ * receives all traffic within that partition as
+ * identified by a unique identifier for the
+ * PF (e.g. S-Tag). If a unique outer VLAN
+ * for the PF is specified, then the setting of
+ * promiscuous mode on that PF shall result in the
+ * PF receiving all host bound traffic with matching
+ * outer VLAN.
+ * # A VF shall can be set in the promiscuous mode.
+ * In the promiscuous mode, the VF does not receive any
+ * traffic unless a unique outer VLAN for the
+ * VF is specified. If a unique outer VLAN
+ * for the VF is specified, then the setting of
+ * promiscuous mode on that VF shall result in the
+ * VF receiving all host bound traffic with the
+ * matching outer VLAN.
+ * # The HWRM shall allow the setting of promiscuous
+ * mode on a function independently from the
+ * promiscuous mode settings on other functions.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS \
+ UINT32_C(0x10)
+ /*
+ * If this flag is set, the corresponding RX
+ * filters shall be set up to cover multicast/broadcast
+ * filters for the outermost Layer 2 destination MAC
+ * address field.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST \
+ UINT32_C(0x20)
+ /*
+ * If this flag is set, the corresponding RX
+ * filters shall be set up to cover multicast/broadcast
+ * filters for the VLAN-tagged packets that match the
+ * TPID and VID fields of VLAN tags in the VLAN tag
+ * table specified in this command.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLANONLY \
+ UINT32_C(0x40)
+ /*
+ * If this flag is set, the corresponding RX
+ * filters shall be set up to cover multicast/broadcast
+ * filters for non-VLAN tagged packets and VLAN-tagged
+ * packets that match the TPID and VID fields of VLAN
+ * tags in the VLAN tag table specified in this command.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLAN_NONVLAN \
+ UINT32_C(0x80)
+ /*
+ * If this flag is set, the corresponding RX
+ * filters shall be set up to cover multicast/broadcast
+ * filters for non-VLAN tagged packets and VLAN-tagged
+ * packets matching any VLAN tag.
+ *
+ * If this flag is set, then the HWRM shall ignore
+ * VLAN tags specified in vlan_tag_tbl.
+ *
+ * If none of vlanonly, vlan_nonvlan, and anyvlan_nonvlan
+ * flags is set, then the HWRM shall ignore
+ * VLAN tags specified in vlan_tag_tbl.
+ *
+ * The HWRM client shall set at most one flag out of
+ * vlanonly, vlan_nonvlan, and anyvlan_nonvlan.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ANYVLAN_NONVLAN \
+ UINT32_C(0x100)
+ /* This is the address for mcast address tbl. */
+ uint64_t mc_tbl_addr;
+ /*
+ * This value indicates how many entries in mc_tbl are valid.
+ * Each entry is 6 bytes.
+ */
+ uint32_t num_mc_entries;
+ uint8_t unused_0[4];
+ /*
+ * This is the address for VLAN tag table.
+ * Each VLAN entry in the table is 4 bytes of a VLAN tag
+ * including TPID, PCP, DEI, and VID fields in network byte
+ * order.
+ */
+ uint64_t vlan_tag_tbl_addr;
+ /*
+ * This value indicates how many entries in vlan_tag_tbl are
+ * valid. Each entry is 4 bytes.
+ */
+ uint32_t num_vlan_tags;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_cfa_l2_set_rx_mask_output (size:128b/16B) */
+struct hwrm_cfa_l2_set_rx_mask_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* hwrm_cfa_l2_set_rx_mask_cmd_err (size:64b/8B) */
+struct hwrm_cfa_l2_set_rx_mask_cmd_err {
+ /*
+ * command specific error codes that goes to
+ * the cmd_err field in Common HWRM Error Response.
+ */
+ uint8_t code;
+ /* Unknown error */
+ #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_UNKNOWN \
+ UINT32_C(0x0)
+ /* Unable to complete operation due to conflict with Ntuple Filter */
+ #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_NTUPLE_FILTER_CONFLICT_ERR \
+ UINT32_C(0x1)
+ #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_LAST \
+ HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_NTUPLE_FILTER_CONFLICT_ERR
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_vlan_antispoof_cfg *
+ *******************************/
+
+
+/* hwrm_cfa_vlan_antispoof_cfg_input (size:256b/32B) */
+struct hwrm_cfa_vlan_antispoof_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Function ID of the function that is being configured.
+ * Only valid for a VF FID configured by the PF.
+ */
+ uint16_t fid;
+ uint8_t unused_0[2];
+ /* Number of VLAN entries in the vlan_tag_mask_tbl. */
+ uint32_t num_vlan_entries;
+ /*
+ * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN
+ * antispoof table. Each table entry contains the 16-bit TPID
+ * (0x8100 or 0x88a8 only), 16-bit VLAN ID, and a 16-bit mask,
+ * all in network order to match hwrm_cfa_l2_set_rx_mask.
+ * For an individual VLAN entry, the mask value should be 0xfff
+ * for the 12-bit VLAN ID.
+ */
+ uint64_t vlan_tag_mask_tbl_addr;
+} __rte_packed;
+
+/* hwrm_cfa_vlan_antispoof_cfg_output (size:128b/16B) */
+struct hwrm_cfa_vlan_antispoof_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/********************************
+ * hwrm_cfa_vlan_antispoof_qcfg *
+ ********************************/
+
+
+/* hwrm_cfa_vlan_antispoof_qcfg_input (size:256b/32B) */
+struct hwrm_cfa_vlan_antispoof_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Function ID of the function that is being queried.
+ * Only valid for a VF FID queried by the PF.
+ */
+ uint16_t fid;
+ uint8_t unused_0[2];
+ /*
+ * Maximum number of VLAN entries the firmware is allowed to DMA
+ * to vlan_tag_mask_tbl.
+ */
+ uint32_t max_vlan_entries;
+ /*
+ * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN
+ * antispoof table to which firmware will DMA to. Each table
+ * entry will contain the 16-bit TPID (0x8100 or 0x88a8 only),
+ * 16-bit VLAN ID, and a 16-bit mask, all in network order to
+ * match hwrm_cfa_l2_set_rx_mask. For an individual VLAN entry,
+ * the mask value should be 0xfff for the 12-bit VLAN ID.
+ */
+ uint64_t vlan_tag_mask_tbl_addr;
+} __rte_packed;
+
+/* hwrm_cfa_vlan_antispoof_qcfg_output (size:128b/16B) */
+struct hwrm_cfa_vlan_antispoof_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Number of valid entries DMAd by firmware to vlan_tag_mask_tbl. */
+ uint32_t num_vlan_entries;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/********************************
+ * hwrm_cfa_tunnel_filter_alloc *
+ ********************************/
+
+
+/* hwrm_cfa_tunnel_filter_alloc_input (size:704b/88B) */
+struct hwrm_cfa_tunnel_filter_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* Setting of this flag indicates the applicability to the loopback path. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x1)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the l2_filter_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the l2_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the l2_ivlan field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the l3_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the l3_addr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR_TYPE \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the t_l3_addr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR_TYPE \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the t_l3_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the tunnel_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the vni field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_VNI \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the dst_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_DST_VNIC_ID \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x400)
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value sets the match value for the inner L2
+ * MAC address.
+ * Destination MAC address for RX path.
+ * Source MAC address for TX path.
+ */
+ uint8_t l2_addr[6];
+ /*
+ * This value sets VLAN ID value for inner VLAN.
+ * Only 12-bits of VLAN ID are used in setting the filter.
+ */
+ uint16_t l2_ivlan;
+ /*
+ * The value of inner destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t l3_addr[4];
+ /*
+ * The value of tunnel destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t t_l3_addr[4];
+ /*
+ * This value indicates the type of inner IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t l3_addr_type;
+ /*
+ * This value indicates the type of tunnel IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t t_l3_addr_type;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ /*
+ * tunnel_flags allows the user to indicate the tunnel tag detection
+ * for the tunnel type specified in tunnel_type.
+ */
+ uint8_t tunnel_flags;
+ /*
+ * If the tunnel_type is geneve, then this bit indicates if we
+ * need to match the geneve OAM packet.
+ * If the tunnel_type is nvgre or gre, then this bit indicates if
+ * we need to detect checksum present bit in geneve header.
+ * If the tunnel_type is mpls, then this bit indicates if we need
+ * to match mpls packet with explicit IPV4/IPV6 null header.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_OAM_CHECKSUM_EXPLHDR \
+ UINT32_C(0x1)
+ /*
+ * If the tunnel_type is geneve, then this bit indicates if we
+ * need to detect the critical option bit set in the oam packet.
+ * If the tunnel_type is nvgre or gre, then this bit indicates
+ * if we need to match nvgre packets with key present bit set in
+ * gre header.
+ * If the tunnel_type is mpls, then this bit indicates if we
+ * need to match mpls packet with S bit from inner/second label.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_CRITICAL_OPT_S1 \
+ UINT32_C(0x2)
+ /*
+ * If the tunnel_type is geneve, then this bit indicates if we
+ * need to match geneve packet with extended header bit set in
+ * geneve header.
+ * If the tunnel_type is nvgre or gre, then this bit indicates
+ * if we need to match nvgre packets with sequence number
+ * present bit set in gre header.
+ * If the tunnel_type is mpls, then this bit indicates if we
+ * need to match mpls packet with S bit from out/first label.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_EXTHDR_SEQNUM_S0 \
+ UINT32_C(0x4)
+ /*
+ * Virtual Network Identifier (VNI). Only valid with
+ * tunnel_types VXLAN, NVGRE, and Geneve.
+ * Only lower 24-bits of VNI field are used
+ * in setting up the filter.
+ */
+ uint32_t vni;
+ /* Logical VNIC ID of the destination VNIC. */
+ uint32_t dst_vnic_id;
+ /*
+ * Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint32_t mirror_vnic_id;
+} __rte_packed;
+
+/* hwrm_cfa_tunnel_filter_alloc_output (size:192b/24B) */
+struct hwrm_cfa_tunnel_filter_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t tunnel_filter_id;
+ /*
+ * The flow id value in bit 0-29 is the actual ID of the flow
+ * associated with this filter and it shall be used to match
+ * and associate the flow identifier returned in completion
+ * records. A value of 0xFFFFFFFF in the 32-bit flow_id field
+ * shall indicate no valid flow id.
+ */
+ uint32_t flow_id;
+ /* Indicate the flow id value. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_VALUE_MASK \
+ UINT32_C(0x3fffffff)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_VALUE_SFT 0
+ /* Indicate type of the flow. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE \
+ UINT32_C(0x40000000)
+ /*
+ * If this bit set to 0, then it indicates that the flow is
+ * internal flow.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_INT \
+ (UINT32_C(0x0) << 30)
+ /*
+ * If this bit is set to 1, then it indicates that the flow is
+ * external flow.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT \
+ (UINT32_C(0x1) << 30)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_LAST \
+ HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT
+ /* Indicate the flow direction. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR \
+ UINT32_C(0x80000000)
+ /* If this bit set to 0, then it indicates rx flow. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_RX \
+ (UINT32_C(0x0) << 31)
+ /* If this bit is set to 1, then it indicates that tx flow. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_TX \
+ (UINT32_C(0x1) << 31)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_LAST \
+ HWRM_CFA_TUNNEL_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_TX
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_tunnel_filter_free *
+ *******************************/
+
+
+/* hwrm_cfa_tunnel_filter_free_input (size:192b/24B) */
+struct hwrm_cfa_tunnel_filter_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t tunnel_filter_id;
+} __rte_packed;
+
+/* hwrm_cfa_tunnel_filter_free_output (size:128b/16B) */
+struct hwrm_cfa_tunnel_filter_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************************
+ * hwrm_cfa_redirect_tunnel_type_alloc *
+ ***************************************/
+
+
+/* hwrm_cfa_redirect_tunnel_type_alloc_input (size:192b/24B) */
+struct hwrm_cfa_redirect_tunnel_type_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint16_t dest_fid;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ /* Tunnel alloc flags. */
+ uint8_t flags;
+ /* Setting of this flag indicates modify existing redirect tunnel to new destination function ID. */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_FLAGS_MODIFY_DST \
+ UINT32_C(0x1)
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_cfa_redirect_tunnel_type_alloc_output (size:128b/16B) */
+struct hwrm_cfa_redirect_tunnel_type_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************************
+ * hwrm_cfa_redirect_tunnel_type_free *
+ **************************************/
+
+
+/* hwrm_cfa_redirect_tunnel_type_free_input (size:192b/24B) */
+struct hwrm_cfa_redirect_tunnel_type_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint16_t dest_fid;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_0[5];
+} __rte_packed;
+
+/* hwrm_cfa_redirect_tunnel_type_free_output (size:128b/16B) */
+struct hwrm_cfa_redirect_tunnel_type_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************************
+ * hwrm_cfa_redirect_tunnel_type_info *
+ **************************************/
+
+
+/* hwrm_cfa_redirect_tunnel_type_info_input (size:192b/24B) */
+struct hwrm_cfa_redirect_tunnel_type_info_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The source function id. */
+ uint16_t src_fid;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_0[5];
+} __rte_packed;
+
+/* hwrm_cfa_redirect_tunnel_type_info_output (size:128b/16B) */
+struct hwrm_cfa_redirect_tunnel_type_info_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint16_t dest_fid;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* hwrm_vxlan_ipv4_hdr (size:128b/16B) */
+struct hwrm_vxlan_ipv4_hdr {
+ /* IPv4 version and header length. */
+ uint8_t ver_hlen;
+ /* IPv4 header length */
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_MASK UINT32_C(0xf)
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_SFT 0
+ /* Version */
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_MASK UINT32_C(0xf0)
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_SFT 4
+ /* IPv4 type of service. */
+ uint8_t tos;
+ /* IPv4 identification. */
+ uint16_t ip_id;
+ /* IPv4 flags and offset. */
+ uint16_t flags_frag_offset;
+ /* IPv4 TTL. */
+ uint8_t ttl;
+ /* IPv4 protocol. */
+ uint8_t protocol;
+ /* IPv4 source address. */
+ uint32_t src_ip_addr;
+ /* IPv4 destination address. */
+ uint32_t dest_ip_addr;
+} __rte_packed;
+
+/* hwrm_vxlan_ipv6_hdr (size:320b/40B) */
+struct hwrm_vxlan_ipv6_hdr {
+ /* IPv6 version, traffic class and flow label. */
+ uint32_t ver_tc_flow_label;
+ /* IPv6 version shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_SFT \
+ UINT32_C(0x1c)
+ /* IPv6 version mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_MASK \
+ UINT32_C(0xf0000000)
+ /* IPv6 TC shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_SFT \
+ UINT32_C(0x14)
+ /* IPv6 TC mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_MASK \
+ UINT32_C(0xff00000)
+ /* IPv6 flow label shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_SFT \
+ UINT32_C(0x0)
+ /* IPv6 flow label mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK \
+ UINT32_C(0xfffff)
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_LAST \
+ HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK
+ /* IPv6 payload length. */
+ uint16_t payload_len;
+ /* IPv6 next header. */
+ uint8_t next_hdr;
+ /* IPv6 TTL. */
+ uint8_t ttl;
+ /* IPv6 source address. */
+ uint32_t src_ip_addr[4];
+ /* IPv6 destination address. */
+ uint32_t dest_ip_addr[4];
+} __rte_packed;
+
+/* hwrm_cfa_encap_data_vxlan (size:640b/80B) */
+struct hwrm_cfa_encap_data_vxlan {
+ /* Source MAC address. */
+ uint8_t src_mac_addr[6];
+ /* reserved. */
+ uint16_t unused_0;
+ /* Destination MAC address. */
+ uint8_t dst_mac_addr[6];
+ /* Number of VLAN tags. */
+ uint8_t num_vlan_tags;
+ /* reserved. */
+ uint8_t unused_1;
+ /* Outer VLAN TPID. */
+ uint16_t ovlan_tpid;
+ /* Outer VLAN TCI. */
+ uint16_t ovlan_tci;
+ /* Inner VLAN TPID. */
+ uint16_t ivlan_tpid;
+ /* Inner VLAN TCI. */
+ uint16_t ivlan_tci;
+ /* L3 header fields. */
+ uint32_t l3[10];
+ /* IP version mask. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_MASK UINT32_C(0xf)
+ /* IP version 4. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV4 UINT32_C(0x4)
+ /* IP version 6. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6 UINT32_C(0x6)
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_LAST \
+ HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6
+ /* UDP source port. */
+ uint16_t src_port;
+ /* UDP destination port. */
+ uint16_t dst_port;
+ /* VXLAN Network Identifier. */
+ uint32_t vni;
+ /* 3 bytes VXLAN header reserve fields from 1st dword of the VXLAN header. */
+ uint8_t hdr_rsvd0[3];
+ /* 1 byte VXLAN header reserve field from 2nd dword of the VXLAN header. */
+ uint8_t hdr_rsvd1;
+ /* VXLAN header flags field. */
+ uint8_t hdr_flags;
+ uint8_t unused[3];
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_encap_record_alloc *
+ *******************************/
+
+
+/* hwrm_cfa_encap_record_alloc_input (size:832b/104B) */
+struct hwrm_cfa_encap_record_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* Setting of this flag indicates the applicability to the loopback path. */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x1)
+ /*
+ * Setting of this flag indicates this encap record is external encap record.
+ * Resetting of this flag indicates this flag is internal encap record and
+ * this is the default setting.
+ */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_FLAGS_EXTERNAL \
+ UINT32_C(0x2)
+ /* Encapsulation Type. */
+ uint8_t encap_type;
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) after inside Ethernet payload */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* VLAN */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VLAN \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_LAST \
+ HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN_GPE_V6
+ uint8_t unused_0[3];
+ /* This value is encap data used for the given encap type. */
+ uint32_t encap_data[20];
+} __rte_packed;
+
+/* hwrm_cfa_encap_record_alloc_output (size:128b/16B) */
+struct hwrm_cfa_encap_record_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t encap_record_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************************
+ * hwrm_cfa_encap_record_free *
+ ******************************/
+
+
+/* hwrm_cfa_encap_record_free_input (size:192b/24B) */
+struct hwrm_cfa_encap_record_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t encap_record_id;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_cfa_encap_record_free_output (size:128b/16B) */
+struct hwrm_cfa_encap_record_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/********************************
+ * hwrm_cfa_ntuple_filter_alloc *
+ ********************************/
+
+
+/* hwrm_cfa_ntuple_filter_alloc_input (size:1024b/128B) */
+struct hwrm_cfa_ntuple_filter_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* Setting of this flag indicates the applicability to the loopback path. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x1)
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DROP \
+ UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates that a meter is expected to be attached
+ * to this flow. This hint can be used when choosing the action record
+ * format required for the flow.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_METER \
+ UINT32_C(0x4)
+ /*
+ * Setting of this flag indicates that the dst_id field contains function ID.
+ * If this is not set it indicates dest_id is VNIC or VPORT.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DEST_FID \
+ UINT32_C(0x8)
+ /*
+ * Setting of this flag indicates match on arp reply when ethertype is 0x0806.
+ * If this is not set it indicates no specific arp opcode matching.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_ARP_REPLY \
+ UINT32_C(0x10)
+ /*
+ * Setting of this flag indicates that the dst_id field contains RFS ring
+ * table index. If this is not set it indicates dst_id is VNIC or VPORT
+ * or function ID. Note dest_fid and dest_rfs_ring_idx can’t be set at
+ * the same time.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DEST_RFS_RING_IDX \
+ UINT32_C(0x20)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the l2_filter_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the ethertype field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the tunnel_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the src_macaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the ipaddr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the src_ipaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the src_ipaddr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR_MASK \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the dst_ipaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the dst_ipaddr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR_MASK \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the ip_protocol field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the src_port field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the src_port_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT_MASK \
+ UINT32_C(0x800)
+ /*
+ * This bit must be '1' for the dst_port field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT \
+ UINT32_C(0x1000)
+ /*
+ * This bit must be '1' for the dst_port_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT_MASK \
+ UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the pri_hint field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_PRI_HINT \
+ UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the ntuple_filter_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_NTUPLE_FILTER_ID \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the dst_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x20000)
+ /*
+ * This bit must be '1' for the dst_macaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR \
+ UINT32_C(0x40000)
+ /* This flag is deprecated. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_RFS_RING_TBL_IDX \
+ UINT32_C(0x80000)
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value indicates the source MAC address in
+ * the Ethernet header.
+ */
+ uint8_t src_macaddr[6];
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint16_t ethertype;
+ /*
+ * This value indicates the type of IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t ip_addr_type;
+ /* invalid */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN \
+ UINT32_C(0x0)
+ /* IPv4 */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 \
+ UINT32_C(0x4)
+ /* IPv6 */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 \
+ UINT32_C(0x6)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6
+ /*
+ * The value of protocol filed in IP header.
+ * Applies to UDP and TCP traffic.
+ * 6 - TCP
+ * 17 - UDP
+ */
+ uint8_t ip_protocol;
+ /* invalid */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN \
+ UINT32_C(0x0)
+ /* TCP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP \
+ UINT32_C(0x6)
+ /* UDP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP \
+ UINT32_C(0x11)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP
+ /*
+ * If set, this value shall represent the
+ * Logical VNIC ID of the destination VNIC for the RX
+ * path and network port id of the destination port for
+ * the TX path.
+ */
+ uint16_t dst_id;
+ /*
+ * Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint16_t mirror_vnic_id;
+ /*
+ * This value indicates the tunnel type for this filter.
+ * If this field is not specified, then the filter shall
+ * apply to both non-tunneled and tunneled packets.
+ * If this field conflicts with the tunnel_type specified
+ * in the l2_filter_id, then the HWRM shall return an
+ * error for this command.
+ */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ /*
+ * This hint is provided to help in placing
+ * the filter in the filter table.
+ */
+ uint8_t pri_hint;
+ /* No preference */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
+ UINT32_C(0x0)
+ /* Above the given filter */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE \
+ UINT32_C(0x1)
+ /* Below the given filter */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_BELOW \
+ UINT32_C(0x2)
+ /* As high as possible */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_HIGHEST \
+ UINT32_C(0x3)
+ /* As low as possible */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST \
+ UINT32_C(0x4)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST
+ /*
+ * The value of source IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t src_ipaddr[4];
+ /*
+ * The value of source IP address mask to be used in
+ * filtering.
+ * For IPv4, first four bytes represent the IP address mask.
+ */
+ uint32_t src_ipaddr_mask[4];
+ /*
+ * The value of destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t dst_ipaddr[4];
+ /*
+ * The value of destination IP address mask to be used in
+ * filtering.
+ * For IPv4, first four bytes represent the IP address mask.
+ */
+ uint32_t dst_ipaddr_mask[4];
+ /*
+ * The value of source port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t src_port;
+ /*
+ * The value of source port mask to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t src_port_mask;
+ /*
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_port;
+ /*
+ * The value of destination port mask to be used in
+ * filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_port_mask;
+ /*
+ * This is the ID of the filter that goes along with
+ * the pri_hint.
+ */
+ uint64_t ntuple_filter_id_hint;
+} __rte_packed;
+
+/* hwrm_cfa_ntuple_filter_alloc_output (size:192b/24B) */
+struct hwrm_cfa_ntuple_filter_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t ntuple_filter_id;
+ /*
+ * The flow id value in bit 0-29 is the actual ID of the flow
+ * associated with this filter and it shall be used to match
+ * and associate the flow identifier returned in completion
+ * records. A value of 0xFFFFFFFF in the 32-bit flow_id field
+ * shall indicate no valid flow id.
+ */
+ uint32_t flow_id;
+ /* Indicate the flow id value. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_VALUE_MASK \
+ UINT32_C(0x3fffffff)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_VALUE_SFT 0
+ /* Indicate type of the flow. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE \
+ UINT32_C(0x40000000)
+ /*
+ * If this bit set to 0, then it indicates that the flow is
+ * internal flow.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_INT \
+ (UINT32_C(0x0) << 30)
+ /*
+ * If this bit is set to 1, then it indicates that the flow is
+ * external flow.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT \
+ (UINT32_C(0x1) << 30)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT
+ /* Indicate the flow direction. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR \
+ UINT32_C(0x80000000)
+ /* If this bit set to 0, then it indicates rx flow. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_RX \
+ (UINT32_C(0x0) << 31)
+ /* If this bit is set to 1, then it indicates that tx flow. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_TX \
+ (UINT32_C(0x1) << 31)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_OUTPUT_FLOW_ID_DIR_TX
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* hwrm_cfa_ntuple_filter_alloc_cmd_err (size:64b/8B) */
+struct hwrm_cfa_ntuple_filter_alloc_cmd_err {
+ /*
+ * command specific error codes that goes to
+ * the cmd_err field in Common HWRM Error Response.
+ */
+ uint8_t code;
+ /* Unknown error */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_UNKNOWN \
+ UINT32_C(0x0)
+ /* Unable to complete operation due to conflict with Rx Mask VLAN */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_RX_MASK_VLAN_CONFLICT_ERR \
+ UINT32_C(0x1)
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_LAST \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_RX_MASK_VLAN_CONFLICT_ERR
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_ntuple_filter_free *
+ *******************************/
+
+
+/* hwrm_cfa_ntuple_filter_free_input (size:192b/24B) */
+struct hwrm_cfa_ntuple_filter_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t ntuple_filter_id;
+} __rte_packed;
+
+/* hwrm_cfa_ntuple_filter_free_output (size:128b/16B) */
+struct hwrm_cfa_ntuple_filter_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************************
+ * hwrm_cfa_ntuple_filter_cfg *
+ ******************************/
+
+
+/* hwrm_cfa_ntuple_filter_cfg_input (size:384b/48B) */
+struct hwrm_cfa_ntuple_filter_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the new_dst_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_DST_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the new_meter_instance_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
+ UINT32_C(0x4)
+ uint32_t flags;
+ /*
+ * Setting this bit to 1 indicates that dest_id field contains FID.
+ * Setting this to 0 indicates that dest_id field contains VNIC or VPORT.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_FLAGS_DEST_FID \
+ UINT32_C(0x1)
+ /*
+ * Setting of this flag indicates that the new_dst_id field contains
+ * RFS ring table index. If this is not set it indicates new_dst_id is
+ * VNIC or VPORT or function ID. Note dest_fid and dest_rfs_ring_idx
+ * can’t be set at the same time.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_FLAGS_DEST_RFS_RING_IDX \
+ UINT32_C(0x2)
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t ntuple_filter_id;
+ /*
+ * If set, this value shall represent the new
+ * Logical VNIC ID of the destination VNIC for the RX
+ * path and new network port id of the destination port for
+ * the TX path.
+ */
+ uint32_t new_dst_id;
+ /*
+ * New Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint32_t new_mirror_vnic_id;
+ /*
+ * New meter to attach to the flow. Specifying the
+ * invalid instance ID is used to remove any existing
+ * meter from the flow.
+ */
+ uint16_t new_meter_instance_id;
+ /*
+ * A value of 0xfff is considered invalid and implies the
+ * instance is not configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_LAST \
+ HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID
+ uint8_t unused_1[6];
+} __rte_packed;
+
+/* hwrm_cfa_ntuple_filter_cfg_output (size:128b/16B) */
+struct hwrm_cfa_ntuple_filter_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_cfa_em_flow_alloc *
+ **************************/
+
+
+/* hwrm_cfa_em_flow_alloc_input (size:896b/112B) */
+struct hwrm_cfa_em_flow_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates enabling of a byte counter for a given
+ * flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_BYTE_CTR UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates enabling of a packet counter for a given
+ * flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PKT_CTR UINT32_C(0x4)
+ /* Setting of this flag indicates de-capsulation action for the given flow. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DECAP UINT32_C(0x8)
+ /* Setting of this flag indicates encapsulation action for the given flow. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_ENCAP UINT32_C(0x10)
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x20)
+ /*
+ * Setting of this flag indicates that a meter is expected to be attached
+ * to this flow. This hint can be used when choosing the action record
+ * format required for the flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_METER UINT32_C(0x40)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the l2_filter_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the tunnel_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the tunnel_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_ID \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the src_macaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_MACADDR \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the dst_macaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_MACADDR \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the ovlan_vid field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_OVLAN_VID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the ivlan_vid field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IVLAN_VID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the ethertype field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ETHERTYPE \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the src_ipaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_IPADDR \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the dst_ipaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_IPADDR \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the ipaddr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the ip_protocol field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
+ UINT32_C(0x800)
+ /*
+ * This bit must be '1' for the src_port field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_PORT \
+ UINT32_C(0x1000)
+ /*
+ * This bit must be '1' for the dst_port field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_PORT \
+ UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the dst_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the encap_record_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ENCAP_RECORD_ID \
+ UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the meter_instance_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_METER_INSTANCE_ID \
+ UINT32_C(0x20000)
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_0[3];
+ /*
+ * Tunnel identifier.
+ * Virtual Network Identifier (VNI). Only valid with
+ * tunnel_types VXLAN, NVGRE, and Geneve.
+ * Only lower 24-bits of VNI field are used
+ * in setting up the filter.
+ */
+ uint32_t tunnel_id;
+ /*
+ * This value indicates the source MAC address in
+ * the Ethernet header.
+ */
+ uint8_t src_macaddr[6];
+ /* The meter instance to attach to the flow. */
+ uint16_t meter_instance_id;
+ /*
+ * A value of 0xfff is considered invalid and implies the
+ * instance is not configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID
+ /*
+ * This value indicates the destination MAC address in
+ * the Ethernet header.
+ */
+ uint8_t dst_macaddr[6];
+ /*
+ * This value indicates the VLAN ID of the outer VLAN tag
+ * in the Ethernet header.
+ */
+ uint16_t ovlan_vid;
+ /*
+ * This value indicates the VLAN ID of the inner VLAN tag
+ * in the Ethernet header.
+ */
+ uint16_t ivlan_vid;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint16_t ethertype;
+ /*
+ * This value indicates the type of IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t ip_addr_type;
+ /* invalid */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN UINT32_C(0x0)
+ /* IPv4 */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 UINT32_C(0x4)
+ /* IPv6 */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 UINT32_C(0x6)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6
+ /*
+ * The value of protocol filed in IP header.
+ * Applies to UDP and TCP traffic.
+ * 6 - TCP
+ * 17 - UDP
+ */
+ uint8_t ip_protocol;
+ /* invalid */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN UINT32_C(0x0)
+ /* TCP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_TCP UINT32_C(0x6)
+ /* UDP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP UINT32_C(0x11)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP
+ uint8_t unused_1[2];
+ /*
+ * The value of source IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t src_ipaddr[4];
+ /*
+ * big_endian = True
+ * The value of destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t dst_ipaddr[4];
+ /*
+ * The value of source port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t src_port;
+ /*
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_port;
+ /*
+ * If set, this value shall represent the
+ * Logical VNIC ID of the destination VNIC for the RX
+ * path and network port id of the destination port for
+ * the TX path.
+ */
+ uint16_t dst_id;
+ /*
+ * Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint16_t mirror_vnic_id;
+ /* Logical ID of the encapsulation record. */
+ uint32_t encap_record_id;
+ uint8_t unused_2[4];
+} __rte_packed;
+
+/* hwrm_cfa_em_flow_alloc_output (size:192b/24B) */
+struct hwrm_cfa_em_flow_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t em_filter_id;
+ /*
+ * The flow id value in bit 0-29 is the actual ID of the flow
+ * associated with this filter and it shall be used to match
+ * and associate the flow identifier returned in completion
+ * records. A value of 0xFFFFFFFF in the 32-bit flow_id field
+ * shall indicate no valid flow id.
+ */
+ uint32_t flow_id;
+ /* Indicate the flow id value. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_VALUE_MASK \
+ UINT32_C(0x3fffffff)
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_VALUE_SFT 0
+ /* Indicate type of the flow. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE \
+ UINT32_C(0x40000000)
+ /*
+ * If this bit set to 0, then it indicates that the flow is
+ * internal flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_INT \
+ (UINT32_C(0x0) << 30)
+ /*
+ * If this bit is set to 1, then it indicates that the flow is
+ * external flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT \
+ (UINT32_C(0x1) << 30)
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT
+ /* Indicate the flow direction. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR \
+ UINT32_C(0x80000000)
+ /* If this bit set to 0, then it indicates rx flow. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_RX \
+ (UINT32_C(0x0) << 31)
+ /* If this bit is set to 1, then it indicates that tx flow. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_TX \
+ (UINT32_C(0x1) << 31)
+ #define HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_LAST \
+ HWRM_CFA_EM_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_TX
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_cfa_em_flow_free *
+ *************************/
+
+
+/* hwrm_cfa_em_flow_free_input (size:192b/24B) */
+struct hwrm_cfa_em_flow_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t em_filter_id;
+} __rte_packed;
+
+/* hwrm_cfa_em_flow_free_output (size:128b/16B) */
+struct hwrm_cfa_em_flow_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/************************
+ * hwrm_cfa_meter_qcaps *
+ ************************/
+
+
+/* hwrm_cfa_meter_qcaps_input (size:128b/16B) */
+struct hwrm_cfa_meter_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_cfa_meter_qcaps_output (size:320b/40B) */
+struct hwrm_cfa_meter_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the clock at which the Meter is running with.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_QCAPS_OUTPUT_FLAGS_CLOCK_MASK UINT32_C(0xf)
+ #define HWRM_CFA_METER_QCAPS_OUTPUT_FLAGS_CLOCK_SFT 0
+ /* 375 MHz */
+ #define HWRM_CFA_METER_QCAPS_OUTPUT_FLAGS_CLOCK_375MHZ UINT32_C(0x0)
+ /* 625 MHz */
+ #define HWRM_CFA_METER_QCAPS_OUTPUT_FLAGS_CLOCK_625MHZ UINT32_C(0x1)
+ #define HWRM_CFA_METER_QCAPS_OUTPUT_FLAGS_CLOCK_LAST \
+ HWRM_CFA_METER_QCAPS_OUTPUT_FLAGS_CLOCK_625MHZ
+ uint8_t unused_0[4];
+ /*
+ * The minimum guaranteed number of tx meter profiles supported
+ * for this function.
+ */
+ uint16_t min_tx_profile;
+ /*
+ * The maximum non-guaranteed number of tx meter profiles supported
+ * for this function.
+ */
+ uint16_t max_tx_profile;
+ /*
+ * The minimum guaranteed number of rx meter profiles supported
+ * for this function.
+ */
+ uint16_t min_rx_profile;
+ /*
+ * The maximum non-guaranteed number of rx meter profiles supported
+ * for this function.
+ */
+ uint16_t max_rx_profile;
+ /*
+ * The minimum guaranteed number of tx meter instances supported
+ * for this function.
+ */
+ uint16_t min_tx_instance;
+ /*
+ * The maximum non-guaranteed number of tx meter instances supported
+ * for this function.
+ */
+ uint16_t max_tx_instance;
+ /*
+ * The minimum guaranteed number of rx meter instances supported
+ * for this function.
+ */
+ uint16_t min_rx_instance;
+ /*
+ * The maximum non-guaranteed number of rx meter instances supported
+ * for this function.
+ */
+ uint16_t max_rx_instance;
+ uint8_t unused_1[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/********************************
+ * hwrm_cfa_meter_profile_alloc *
+ ********************************/
+
+
+/* hwrm_cfa_meter_profile_alloc_input (size:320b/40B) */
+struct hwrm_cfa_meter_profile_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_FLAGS_PATH_RX
+ /* The meter algorithm type. */
+ uint8_t meter_type;
+ /* RFC 2697 (srTCM) */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC2697 \
+ UINT32_C(0x0)
+ /* RFC 2698 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC2698 \
+ UINT32_C(0x1)
+ /* RFC 4115 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC4115 \
+ UINT32_C(0x2)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_METER_TYPE_RFC4115
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint16_t reserved1;
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint32_t reserved2;
+ /* A meter rate specified in bytes-per-second. */
+ uint32_t commit_rate;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Raw value */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_RAW \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_RATE_BW_VALUE_UNIT_RAW
+ /* A meter burst size specified in bytes. */
+ uint32_t commit_burst;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid value */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID
+ /* A meter rate specified in bytes-per-second. */
+ uint32_t excess_peak_rate;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Raw unit */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_RAW \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_RAW
+ /* A meter burst size specified in bytes. */
+ uint32_t excess_peak_burst;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID
+} __rte_packed;
+
+/* hwrm_cfa_meter_profile_alloc_output (size:128b/16B) */
+struct hwrm_cfa_meter_profile_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value identifies a meter profile in CFA. */
+ uint16_t meter_profile_id;
+ /*
+ * A value of 0xfff is considered invalid and implies the
+ * profile is not configured.
+ */
+ #define HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_LAST \
+ HWRM_CFA_METER_PROFILE_ALLOC_OUTPUT_METER_PROFILE_ID_INVALID
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_meter_profile_free *
+ *******************************/
+
+
+/* hwrm_cfa_meter_profile_free_input (size:192b/24B) */
+struct hwrm_cfa_meter_profile_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_METER_PROFILE_FREE_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ /* This value identifies a meter profile in CFA. */
+ uint16_t meter_profile_id;
+ /*
+ * A value of 0xfff is considered invalid and implies the
+ * profile is not configured.
+ */
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_LAST \
+ HWRM_CFA_METER_PROFILE_FREE_INPUT_METER_PROFILE_ID_INVALID
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_cfa_meter_profile_free_output (size:128b/16B) */
+struct hwrm_cfa_meter_profile_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************************
+ * hwrm_cfa_meter_profile_cfg *
+ ******************************/
+
+
+/* hwrm_cfa_meter_profile_cfg_input (size:320b/40B) */
+struct hwrm_cfa_meter_profile_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_FLAGS_PATH_RX
+ /* The meter algorithm type. */
+ uint8_t meter_type;
+ /* RFC 2697 (srTCM) */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC2697 \
+ UINT32_C(0x0)
+ /* RFC 2698 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC2698 \
+ UINT32_C(0x1)
+ /* RFC 4115 (trTCM) */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC4115 \
+ UINT32_C(0x2)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_TYPE_RFC4115
+ /* This value identifies a meter profile in CFA. */
+ uint16_t meter_profile_id;
+ /*
+ * A value of 0xfff is considered invalid and implies the
+ * profile is not configured.
+ */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_METER_PROFILE_ID_INVALID
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint32_t reserved;
+ /* A meter rate specified in bytes-per-second. */
+ uint32_t commit_rate;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Raw value */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_RAW \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_RATE_BW_VALUE_UNIT_RAW
+ /* A meter burst size specified in bytes. */
+ uint32_t commit_burst;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid value */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_COMMIT_BURST_BW_VALUE_UNIT_INVALID
+ /* A meter rate specified in bytes-per-second. */
+ uint32_t excess_peak_rate;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Raw unit */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_RAW \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_RATE_BW_VALUE_UNIT_RAW
+ /* A meter burst size specified in bytes. */
+ uint32_t excess_peak_burst;
+ /* The bandwidth value. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_LAST \
+ HWRM_CFA_METER_PROFILE_CFG_INPUT_EXCESS_PEAK_BURST_BW_VALUE_UNIT_INVALID
+} __rte_packed;
+
+/* hwrm_cfa_meter_profile_cfg_output (size:128b/16B) */
+struct hwrm_cfa_meter_profile_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************************
+ * hwrm_cfa_meter_instance_alloc *
+ *********************************/
+
+
+/* hwrm_cfa_meter_instance_alloc_input (size:192b/24B) */
+struct hwrm_cfa_meter_instance_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH \
+ UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ /* This value identifies a meter profile in CFA. */
+ uint16_t meter_profile_id;
+ /*
+ * A value of 0xffff is considered invalid and implies the
+ * profile is not configured.
+ */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_LAST \
+ HWRM_CFA_METER_INSTANCE_ALLOC_INPUT_METER_PROFILE_ID_INVALID
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_cfa_meter_instance_alloc_output (size:128b/16B) */
+struct hwrm_cfa_meter_instance_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value identifies a meter instance in CFA. */
+ uint16_t meter_instance_id;
+ /*
+ * A value of 0xffff is considered invalid and implies the
+ * instance is not configured.
+ */
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_LAST \
+ HWRM_CFA_METER_INSTANCE_ALLOC_OUTPUT_METER_INSTANCE_ID_INVALID
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_meter_instance_cfg *
+ *******************************/
+
+
+/* hwrm_cfa_meter_instance_cfg_input (size:192b/24B) */
+struct hwrm_cfa_meter_instance_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_INSTANCE_CFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_METER_INSTANCE_CFG_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_METER_INSTANCE_CFG_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_METER_INSTANCE_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_METER_INSTANCE_CFG_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ /*
+ * This value identifies a new meter profile to be associated with
+ * the meter instance specified in this command.
+ */
+ uint16_t meter_profile_id;
+ /*
+ * A value of 0xffff is considered invalid and implies the
+ * profile is not configured.
+ */
+ #define HWRM_CFA_METER_INSTANCE_CFG_INPUT_METER_PROFILE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_INSTANCE_CFG_INPUT_METER_PROFILE_ID_LAST \
+ HWRM_CFA_METER_INSTANCE_CFG_INPUT_METER_PROFILE_ID_INVALID
+ /*
+ * This value identifies the ID of a meter instance that needs to be updated with
+ * a new meter profile specified in this command.
+ */
+ uint16_t meter_instance_id;
+ uint8_t unused_1[2];
+} __rte_packed;
+
+/* hwrm_cfa_meter_instance_cfg_output (size:128b/16B) */
+struct hwrm_cfa_meter_instance_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/********************************
+ * hwrm_cfa_meter_instance_free *
+ ********************************/
+
+
+/* hwrm_cfa_meter_instance_free_input (size:192b/24B) */
+struct hwrm_cfa_meter_instance_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint8_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x1)
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_METER_INSTANCE_FREE_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0;
+ /* This value identifies a meter instance in CFA. */
+ uint16_t meter_instance_id;
+ /*
+ * A value of 0xfff is considered invalid and implies the
+ * instance is not configured.
+ */
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ #define HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_LAST \
+ HWRM_CFA_METER_INSTANCE_FREE_INPUT_METER_INSTANCE_ID_INVALID
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_cfa_meter_instance_free_output (size:128b/16B) */
+struct hwrm_cfa_meter_instance_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************************
+ * hwrm_cfa_decap_filter_alloc *
+ *******************************/
+
+
+/* hwrm_cfa_decap_filter_alloc_input (size:832b/104B) */
+struct hwrm_cfa_decap_filter_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* ovs_tunnel is 1 b */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_FLAGS_OVS_TUNNEL \
+ UINT32_C(0x1)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the tunnel_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the tunnel_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the src_macaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the dst_macaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the ovlan_vid field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_OVLAN_VID \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the ivlan_vid field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IVLAN_VID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the t_ovlan_vid field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_T_OVLAN_VID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the t_ivlan_vid field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_T_IVLAN_VID \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the ethertype field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the src_ipaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the dst_ipaddr field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the ipaddr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
+ UINT32_C(0x800)
+ /*
+ * This bit must be '1' for the ip_protocol field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
+ UINT32_C(0x1000)
+ /*
+ * This bit must be '1' for the src_port field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT \
+ UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the dst_port field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_PORT \
+ UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the dst_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x10000)
+ /*
+ * Tunnel identifier.
+ * Virtual Network Identifier (VNI). Only valid with
+ * tunnel_types VXLAN, NVGRE, and Geneve.
+ * Only lower 24-bits of VNI field are used
+ * in setting up the filter.
+ */
+ uint32_t tunnel_id;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_0;
+ uint16_t unused_1;
+ /*
+ * This value indicates the source MAC address in
+ * the Ethernet header.
+ */
+ uint8_t src_macaddr[6];
+ uint8_t unused_2[2];
+ /*
+ * This value indicates the destination MAC address in
+ * the Ethernet header.
+ */
+ uint8_t dst_macaddr[6];
+ /*
+ * This value indicates the VLAN ID of the outer VLAN tag
+ * in the Ethernet header.
+ */
+ uint16_t ovlan_vid;
+ /*
+ * This value indicates the VLAN ID of the inner VLAN tag
+ * in the Ethernet header.
+ */
+ uint16_t ivlan_vid;
+ /*
+ * This value indicates the VLAN ID of the outer VLAN tag
+ * in the tunnel Ethernet header.
+ */
+ uint16_t t_ovlan_vid;
+ /*
+ * This value indicates the VLAN ID of the inner VLAN tag
+ * in the tunnel Ethernet header.
+ */
+ uint16_t t_ivlan_vid;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint16_t ethertype;
+ /*
+ * This value indicates the type of IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t ip_addr_type;
+ /* invalid */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN \
+ UINT32_C(0x0)
+ /* IPv4 */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 \
+ UINT32_C(0x4)
+ /* IPv6 */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 \
+ UINT32_C(0x6)
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_LAST \
+ HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6
+ /*
+ * The value of protocol filed in IP header.
+ * Applies to UDP and TCP traffic.
+ * 6 - TCP
+ * 17 - UDP
+ */
+ uint8_t ip_protocol;
+ /* invalid */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN \
+ UINT32_C(0x0)
+ /* TCP */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP \
+ UINT32_C(0x6)
+ /* UDP */
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP \
+ UINT32_C(0x11)
+ #define HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_LAST \
+ HWRM_CFA_DECAP_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP
+ uint16_t unused_3;
+ uint32_t unused_4;
+ /*
+ * The value of source IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t src_ipaddr[4];
+ /*
+ * The value of destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t dst_ipaddr[4];
+ /*
+ * The value of source port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t src_port;
+ /*
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_port;
+ /*
+ * If set, this value shall represent the
+ * Logical VNIC ID of the destination VNIC for the RX
+ * path.
+ */
+ uint16_t dst_id;
+ /*
+ * If set, this value shall represent the L2 context that matches the L2
+ * information of the decap filter.
+ */
+ uint16_t l2_ctxt_ref_id;
+} __rte_packed;
+
+/* hwrm_cfa_decap_filter_alloc_output (size:128b/16B) */
+struct hwrm_cfa_decap_filter_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t decap_filter_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/******************************
+ * hwrm_cfa_decap_filter_free *
+ ******************************/
+
+
+/* hwrm_cfa_decap_filter_free_input (size:192b/24B) */
+struct hwrm_cfa_decap_filter_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t decap_filter_id;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_cfa_decap_filter_free_output (size:128b/16B) */
+struct hwrm_cfa_decap_filter_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_cfa_flow_alloc *
+ ***********************/
+
+
+/* hwrm_cfa_flow_alloc_input (size:1024b/128B) */
+struct hwrm_cfa_flow_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint16_t flags;
+ /* tunnel is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_TUNNEL \
+ UINT32_C(0x1)
+ /* num_vlan is 2 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_MASK \
+ UINT32_C(0x6)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_SFT 1
+ /* no tags */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_NONE \
+ (UINT32_C(0x0) << 1)
+ /* 1 tag */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_ONE \
+ (UINT32_C(0x1) << 1)
+ /* 2 tags */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_TWO \
+ (UINT32_C(0x2) << 1)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_LAST \
+ HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_NUM_VLAN_TWO
+ /* Enumeration denoting the Flow Type. */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_MASK \
+ UINT32_C(0x38)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_SFT 3
+ /* L2 flow */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_L2 \
+ (UINT32_C(0x0) << 3)
+ /* IPV4 flow */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV4 \
+ (UINT32_C(0x1) << 3)
+ /* IPV6 flow */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV6 \
+ (UINT32_C(0x2) << 3)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_LAST \
+ HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_FLOWTYPE_IPV6
+ /*
+ * when set to 1, indicates TX flow offload for function specified in src_fid and
+ * the dst_fid should be set to invalid value. To indicate a VM to VM flow, both
+ * of the path_tx and path_rx flags need to be set. For virtio vSwitch offload
+ * case, the src_fid and dst_fid is set to the same fid value. For the SRIOV
+ * vSwitch offload case, the src_fid and dst_fid must be set to the same VF FID
+ * belong to the children VFs of the same PF to indicate VM to VM flow.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_PATH_TX \
+ UINT32_C(0x40)
+ /*
+ * when set to 1, indicates RX flow offload for function specified in dst_fid and
+ * the src_fid should be set to invalid value.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_PATH_RX \
+ UINT32_C(0x80)
+ /*
+ * Set to 1 to indicate matching of VXLAN VNI from the custom vxlan header is
+ * required and the VXLAN VNI value is stored in the first 24 bits of the dmac field.
+ * This flag is only valid when the flow direction is RX.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_MATCH_VXLAN_IP_VNI \
+ UINT32_C(0x100)
+ /* Set to 1 to indicate vhost_id is specified in the outer_vlan_tci field. */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_FLAGS_VHOST_ID_USE_VLAN \
+ UINT32_C(0x200)
+ /*
+ * Tx Flow: vf fid.
+ * Rx Flow: pf fid.
+ */
+ uint16_t src_fid;
+ /* Tunnel handle valid when tunnel flag is set. */
+ uint32_t tunnel_handle;
+ uint16_t action_flags;
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_FWD \
+ UINT32_C(0x1)
+ /* recycle is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_RECYCLE \
+ UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates drop action. If this flag is not set,
+ * then it should be considered accept action.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_DROP \
+ UINT32_C(0x4)
+ /* meter is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_METER \
+ UINT32_C(0x8)
+ /* tunnel is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TUNNEL \
+ UINT32_C(0x10)
+ /* nat_src is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_SRC \
+ UINT32_C(0x20)
+ /* nat_dest is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_DEST \
+ UINT32_C(0x40)
+ /* nat_ipv4_address is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NAT_IPV4_ADDRESS \
+ UINT32_C(0x80)
+ /* l2_header_rewrite is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_L2_HEADER_REWRITE \
+ UINT32_C(0x100)
+ /* ttl_decrement is 1 b */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TTL_DECREMENT \
+ UINT32_C(0x200)
+ /*
+ * If set to 1 and flow direction is TX, it indicates decap of L2 header
+ * and encap of tunnel header. If set to 1 and flow direction is RX, it
+ * indicates decap of tunnel header and encap L2 header. The type of tunnel
+ * is specified in the tunnel_type field.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_TUNNEL_IP \
+ UINT32_C(0x400)
+ /* If set to 1, flow aging is enabled for this flow. */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_FLOW_AGING_ENABLED \
+ UINT32_C(0x800)
+ /*
+ * If set to 1 an attempt will be made to try to offload this flow to the
+ * most optimal flow table resource. If set to 0, the flow will be
+ * placed to the default flow table resource.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_PRI_HINT \
+ UINT32_C(0x1000)
+ /*
+ * If set to 1 there will be no attempt to allocate an on-chip try to
+ * offload this flow. If set to 0, which will keep compatibility with the
+ * older drivers, will cause the FW to attempt to allocate an on-chip flow
+ * counter for the newly created flow. This will keep the existing behavior
+ * with EM flows which always had an associated flow counter.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_ACTION_FLAGS_NO_FLOW_COUNTER_ALLOC \
+ UINT32_C(0x2000)
+ /*
+ * Tx Flow: pf or vf fid.
+ * Rx Flow: vf fid.
+ */
+ uint16_t dst_fid;
+ /* VLAN tpid, valid when push_vlan flag is set. */
+ uint16_t l2_rewrite_vlan_tpid;
+ /* VLAN tci, valid when push_vlan flag is set. */
+ uint16_t l2_rewrite_vlan_tci;
+ /* Meter id, valid when meter flag is set. */
+ uint16_t act_meter_id;
+ /* Flow with the same l2 context tcam key. */
+ uint16_t ref_flow_handle;
+ /* This value sets the match value for the ethertype. */
+ uint16_t ethertype;
+ /* valid when num tags is 1 or 2. */
+ uint16_t outer_vlan_tci;
+ /* This value sets the match value for the Destination MAC address. */
+ uint16_t dmac[3];
+ /* valid when num tags is 2. */
+ uint16_t inner_vlan_tci;
+ /* This value sets the match value for the Source MAC address. */
+ uint16_t smac[3];
+ /* The bit length of destination IP address mask. */
+ uint8_t ip_dst_mask_len;
+ /* The bit length of source IP address mask. */
+ uint8_t ip_src_mask_len;
+ /* The value of destination IPv4/IPv6 address. */
+ uint32_t ip_dst[4];
+ /* The source IPv4/IPv6 address. */
+ uint32_t ip_src[4];
+ /*
+ * The value of source port.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t l4_src_port;
+ /*
+ * The value of source port mask.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t l4_src_port_mask;
+ /*
+ * The value of destination port.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t l4_dst_port;
+ /*
+ * The value of destination port mask.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t l4_dst_port_mask;
+ /*
+ * NAT IPv4/6 address based on address type flag.
+ * 0 values are ignored.
+ */
+ uint32_t nat_ip_address[4];
+ /* L2 header re-write Destination MAC address. */
+ uint16_t l2_rewrite_dmac[3];
+ /*
+ * The NAT source/destination port based on direction flag.
+ * Applies to UDP and TCP traffic.
+ * 0 values are ignored.
+ */
+ uint16_t nat_port;
+ /* L2 header re-write Source MAC address. */
+ uint16_t l2_rewrite_smac[3];
+ /* The value of ip protocol. */
+ uint8_t ip_proto;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+} __rte_packed;
+
+/* hwrm_cfa_flow_alloc_output (size:256b/32B) */
+struct hwrm_cfa_flow_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Flow record index. */
+ uint16_t flow_handle;
+ uint8_t unused_0[2];
+ /*
+ * The flow id value in bit 0-29 is the actual ID of the flow
+ * associated with this filter and it shall be used to match
+ * and associate the flow identifier returned in completion
+ * records. A value of 0xFFFFFFFF in the 32-bit flow_id field
+ * shall indicate no valid flow id.
+ */
+ uint32_t flow_id;
+ /* Indicate the flow id value. */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_VALUE_MASK \
+ UINT32_C(0x3fffffff)
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_VALUE_SFT 0
+ /* Indicate type of the flow. */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE \
+ UINT32_C(0x40000000)
+ /*
+ * If this bit set to 0, then it indicates that the flow is
+ * internal flow.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_INT \
+ (UINT32_C(0x0) << 30)
+ /*
+ * If this bit is set to 1, then it indicates that the flow is
+ * external flow.
+ */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT \
+ (UINT32_C(0x1) << 30)
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_LAST \
+ HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_TYPE_EXT
+ /* Indicate the flow direction. */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR \
+ UINT32_C(0x80000000)
+ /* If this bit set to 0, then it indicates rx flow. */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_RX \
+ (UINT32_C(0x0) << 31)
+ /* If this bit is set to 1, then it indicates that tx flow. */
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_TX \
+ (UINT32_C(0x1) << 31)
+ #define HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_LAST \
+ HWRM_CFA_FLOW_ALLOC_OUTPUT_FLOW_ID_DIR_TX
+ /* This value identifies a set of CFA data structures used for a flow. */
+ uint64_t ext_flow_handle;
+ uint32_t flow_counter_id;
+ uint8_t unused_1[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* hwrm_cfa_flow_alloc_cmd_err (size:64b/8B) */
+struct hwrm_cfa_flow_alloc_cmd_err {
+ /*
+ * command specific error codes that goes to
+ * the cmd_err field in Common HWRM Error Response.
+ */
+ uint8_t code;
+ /* Unknown error */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_UNKNOWN UINT32_C(0x0)
+ /* No more L2 Context TCAM */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_L2_CONTEXT_TCAM UINT32_C(0x1)
+ /* No more action records */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_ACTION_RECORD UINT32_C(0x2)
+ /* No more flow counters */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_FLOW_COUNTER UINT32_C(0x3)
+ /* No more wild-card TCAM */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_WILD_CARD_TCAM UINT32_C(0x4)
+ /* Hash collsion in exact match tables */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_HASH_COLLISION UINT32_C(0x5)
+ /* Key is already installed */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_KEY_EXISTS UINT32_C(0x6)
+ /* Flow Context DB is out of resource */
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_FLOW_CTXT_DB UINT32_C(0x7)
+ #define HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_LAST \
+ HWRM_CFA_FLOW_ALLOC_CMD_ERR_CODE_FLOW_CTXT_DB
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/**********************
+ * hwrm_cfa_flow_free *
+ **********************/
+
+
+/* hwrm_cfa_flow_free_input (size:256b/32B) */
+struct hwrm_cfa_flow_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Flow record index. */
+ uint16_t flow_handle;
+ uint16_t unused_0;
+ /* Flow counter id to be freed. */
+ uint32_t flow_counter_id;
+ /* This value identifies a set of CFA data structures used for a flow. */
+ uint64_t ext_flow_handle;
+} __rte_packed;
+
+/* hwrm_cfa_flow_free_output (size:256b/32B) */
+struct hwrm_cfa_flow_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* packet is 64 b */
+ uint64_t packet;
+ /* byte is 64 b */
+ uint64_t byte;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* hwrm_cfa_flow_action_data (size:960b/120B) */
+struct hwrm_cfa_flow_action_data {
+ uint16_t action_flags;
+ /* Setting of this flag indicates accept action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_FWD \
+ UINT32_C(0x1)
+ /* Setting of this flag indicates recycle action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_RECYCLE \
+ UINT32_C(0x2)
+ /* Setting of this flag indicates drop action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_DROP \
+ UINT32_C(0x4)
+ /* Setting of this flag indicates meter action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_METER \
+ UINT32_C(0x8)
+ /* Setting of this flag indicates tunnel action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_TUNNEL \
+ UINT32_C(0x10)
+ /*
+ * If set to 1 and flow direction is TX, it indicates decap of L2 header
+ * and encap of tunnel header. If set to 1 and flow direction is RX, it
+ * indicates decap of tunnel header and encap L2 header.
+ */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_TUNNEL_IP \
+ UINT32_C(0x20)
+ /* Setting of this flag indicates ttl decrement action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_TTL_DECREMENT \
+ UINT32_C(0x40)
+ /* If set to 1, flow aging is enabled for this flow. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_FLOW_AGING_ENABLED \
+ UINT32_C(0x80)
+ /* Setting of this flag indicates encap action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_ENCAP \
+ UINT32_C(0x100)
+ /* Setting of this flag indicates decap action. */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ACTION_FLAGS_DECAP \
+ UINT32_C(0x200)
+ /* Meter id. */
+ uint16_t act_meter_id;
+ /* VNIC id. */
+ uint16_t vnic_id;
+ /* vport number. */
+ uint16_t vport_id;
+ /* The NAT source/destination. */
+ uint16_t nat_port;
+ uint16_t unused_0[3];
+ /* NAT IPv4/IPv6 address. */
+ uint32_t nat_ip_address[4];
+ /* Encapsulation Type. */
+ uint8_t encap_type;
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_VXLAN UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_NVGRE UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) after inside Ethernet payload */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_L2GRE UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_IPIP UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_GENEVE UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_MPLS UINT32_C(0x6)
+ /* VLAN */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_VLAN UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_IPGRE UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_VXLAN_V4 UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_IPGRE_V1 UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_L2_ETYPE UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_VXLAN_GPE_V6 UINT32_C(0xc)
+ #define HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_LAST \
+ HWRM_CFA_FLOW_ACTION_DATA_ENCAP_TYPE_VXLAN_GPE_V6
+ uint8_t unused[7];
+ /* This value is encap data for the associated encap type. */
+ uint32_t encap_data[20];
+} __rte_packed;
+
+/* hwrm_cfa_flow_tunnel_hdr_data (size:64b/8B) */
+struct hwrm_cfa_flow_tunnel_hdr_data {
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_L2_ETYPE \
+ UINT32_C(0xb)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_VXLAN_GPE_V6 \
+ UINT32_C(0xc)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_LAST \
+ HWRM_CFA_FLOW_TUNNEL_HDR_DATA_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused[3];
+ /*
+ * Tunnel identifier.
+ * Virtual Network Identifier (VNI).
+ */
+ uint32_t tunnel_id;
+} __rte_packed;
+
+/* hwrm_cfa_flow_l4_key_data (size:64b/8B) */
+struct hwrm_cfa_flow_l4_key_data {
+ /* The value of source port. */
+ uint16_t l4_src_port;
+ /* The value of destination port. */
+ uint16_t l4_dst_port;
+ uint32_t unused;
+} __rte_packed;
+
+/* hwrm_cfa_flow_l3_key_data (size:512b/64B) */
+struct hwrm_cfa_flow_l3_key_data {
+ /* The value of ip protocol. */
+ uint8_t ip_protocol;
+ uint8_t unused_0[7];
+ /* The value of destination IPv4/IPv6 address. */
+ uint32_t ip_dst[4];
+ /* The source IPv4/IPv6 address. */
+ uint32_t ip_src[4];
+ /* NAT IPv4/IPv6 address. */
+ uint32_t nat_ip_address[4];
+ uint32_t unused[2];
+} __rte_packed;
+
+/* hwrm_cfa_flow_l2_key_data (size:448b/56B) */
+struct hwrm_cfa_flow_l2_key_data {
+ /* Destination MAC address. */
+ uint16_t dmac[3];
+ uint16_t unused_0;
+ /* Source MAC address. */
+ uint16_t smac[3];
+ uint16_t unused_1;
+ /* L2 header re-write Destination MAC address. */
+ uint16_t l2_rewrite_dmac[3];
+ uint16_t unused_2;
+ /* L2 header re-write Source MAC address. */
+ uint16_t l2_rewrite_smac[3];
+ /* Ethertype. */
+ uint16_t ethertype;
+ /* Number of VLAN tags. */
+ uint16_t num_vlan_tags;
+ /* VLAN tpid. */
+ uint16_t l2_rewrite_vlan_tpid;
+ /* VLAN tci. */
+ uint16_t l2_rewrite_vlan_tci;
+ uint8_t unused_3[2];
+ /* Outer VLAN TPID. */
+ uint16_t ovlan_tpid;
+ /* Outer VLAN TCI. */
+ uint16_t ovlan_tci;
+ /* Inner VLAN TPID. */
+ uint16_t ivlan_tpid;
+ /* Inner VLAN TCI. */
+ uint16_t ivlan_tci;
+ uint8_t unused[8];
+} __rte_packed;
+
+/* hwrm_cfa_flow_key_data (size:4160b/520B) */
+struct hwrm_cfa_flow_key_data {
+ /* Flow associated tunnel L2 header key info. */
+ uint32_t t_l2_key_data[14];
+ /* Flow associated tunnel L2 header mask info. */
+ uint32_t t_l2_key_mask[14];
+ /* Flow associated tunnel L3 header key info. */
+ uint32_t t_l3_key_data[16];
+ /* Flow associated tunnel L3 header mask info. */
+ uint32_t t_l3_key_mask[16];
+ /* Flow associated tunnel L4 header key info. */
+ uint32_t t_l4_key_data[2];
+ /* Flow associated tunnel L4 header mask info. */
+ uint32_t t_l4_key_mask[2];
+ /* Flow associated tunnel header info. */
+ uint32_t tunnel_hdr[2];
+ /* Flow associated L2 header key info. */
+ uint32_t l2_key_data[14];
+ /* Flow associated L2 header mask info. */
+ uint32_t l2_key_mask[14];
+ /* Flow associated L3 header key info. */
+ uint32_t l3_key_data[16];
+ /* Flow associated L3 header mask info. */
+ uint32_t l3_key_mask[16];
+ /* Flow associated L4 header key info. */
+ uint32_t l4_key_data[2];
+ /* Flow associated L4 header mask info. */
+ uint32_t l4_key_mask[2];
+} __rte_packed;
+
+/**********************
+ * hwrm_cfa_flow_info *
+ **********************/
+
+
+/* hwrm_cfa_flow_info_input (size:256b/32B) */
+struct hwrm_cfa_flow_info_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Flow record index. */
+ uint16_t flow_handle;
+ /* Max flow handle */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_MAX_MASK \
+ UINT32_C(0xfff)
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_MAX_SFT 0
+ /* CNP flow handle */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_CNP_CNT \
+ UINT32_C(0x1000)
+ /* RoCEv1 flow handle */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_ROCEV1_CNT \
+ UINT32_C(0x2000)
+ /* RoCEv2 flow handle */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_ROCEV2_CNT \
+ UINT32_C(0x4000)
+ /* Direction rx = 1 */
+ #define HWRM_CFA_FLOW_INFO_INPUT_FLOW_HANDLE_DIR_RX \
+ UINT32_C(0x8000)
+ uint8_t unused_0[6];
+ /* This value identifies a set of CFA data structures used for a flow. */
+ uint64_t ext_flow_handle;
+} __rte_packed;
+
+/* hwrm_cfa_flow_info_output (size:5632b/704B) */
+struct hwrm_cfa_flow_info_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t flags;
+ /* When set to 1, indicates the configuration is the TX flow. */
+ #define HWRM_CFA_FLOW_INFO_OUTPUT_FLAGS_PATH_TX UINT32_C(0x1)
+ /* When set to 1, indicates the configuration is the RX flow. */
+ #define HWRM_CFA_FLOW_INFO_OUTPUT_FLAGS_PATH_RX UINT32_C(0x2)
+ /* profile is 8 b */
+ uint8_t profile;
+ /* src_fid is 16 b */
+ uint16_t src_fid;
+ /* dst_fid is 16 b */
+ uint16_t dst_fid;
+ /* l2_ctxt_id is 16 b */
+ uint16_t l2_ctxt_id;
+ /* em_info is 64 b */
+ uint64_t em_info;
+ /* tcam_info is 64 b */
+ uint64_t tcam_info;
+ /* vfp_tcam_info is 64 b */
+ uint64_t vfp_tcam_info;
+ /* ar_id is 16 b */
+ uint16_t ar_id;
+ /* flow_handle is 16 b */
+ uint16_t flow_handle;
+ /* tunnel_handle is 32 b */
+ uint32_t tunnel_handle;
+ /* The flow aging timer for the flow, the unit is 100 milliseconds */
+ uint16_t flow_timer;
+ uint8_t unused_0[6];
+ /* Flow associated L2, L3 and L4 headers info. */
+ uint32_t flow_key_data[130];
+ /* Flow associated action record info. */
+ uint32_t flow_action_info[30];
+ uint8_t unused_1[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_cfa_flow_flush *
+ ***********************/
+
+
+/* hwrm_cfa_flow_flush_input (size:256b/32B) */
+struct hwrm_cfa_flow_flush_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* flags is 32 b */
+ uint32_t flags;
+ /*
+ * Set to 1 to indicate the page size, page layers, and flow_handle_table_dma_addr
+ * fields are valid. The flow flush operation should only flush the flows from the
+ * flow table specified. This flag is set to 0 by older driver. For older firmware,
+ * setting this flag has no effect.
+ */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_TABLE_VALID \
+ UINT32_C(0x1)
+ /*
+ * Set to 1 to indicate flow flush operation to cleanup all the flows, meters, CFA
+ * context memory tables etc. This flag is set to 0 by older driver. For older firmware,
+ * setting this flag has no effect.
+ */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_RESET_ALL \
+ UINT32_C(0x2)
+ /*
+ * Set to 1 to indicate flow flush operation to cleanup all the flows by the caller.
+ * This flag is set to 0 by older driver. For older firmware, setting this flag has no effect.
+ */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_RESET_PORT \
+ UINT32_C(0x4)
+ /* Set to 1 to indicate the flow counter IDs are included in the flow table. */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_INCL_FC \
+ UINT32_C(0x8000000)
+ /*
+ * This specifies the size of flow handle entries provided by the driver
+ * in the flow table specified below. Only two flow handle size enums are defined.
+ */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_ENTRY_SIZE_MASK \
+ UINT32_C(0xc0000000)
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_ENTRY_SIZE_SFT \
+ 30
+ /* The flow handle is 16bit */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_ENTRY_SIZE_FLOW_HND_16BIT \
+ (UINT32_C(0x0) << 30)
+ /* The flow handle is 64bit */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_ENTRY_SIZE_FLOW_HND_64BIT \
+ (UINT32_C(0x1) << 30)
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_ENTRY_SIZE_LAST \
+ HWRM_CFA_FLOW_FLUSH_INPUT_FLAGS_FLOW_HANDLE_ENTRY_SIZE_FLOW_HND_64BIT
+ /* Specify page size of the flow table memory. */
+ uint8_t page_size;
+ /* The page size is 4K */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_4K UINT32_C(0x0)
+ /* The page size is 8K */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_8K UINT32_C(0x1)
+ /* The page size is 64K */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_64K UINT32_C(0x4)
+ /* The page size is 256K */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_256K UINT32_C(0x6)
+ /* The page size is 1M */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_1M UINT32_C(0x8)
+ /* The page size is 2M */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_2M UINT32_C(0x9)
+ /* The page size is 4M */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_4M UINT32_C(0xa)
+ /* The page size is 1G */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_1G UINT32_C(0x12)
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_LAST \
+ HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_SIZE_1G
+ /* FLow table memory indirect levels. */
+ uint8_t page_level;
+ /* PBL pointer is physical start address. */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_LEVEL_LVL_0 UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_LEVEL_LVL_1 UINT32_C(0x1)
+ /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_LEVEL_LVL_2 UINT32_C(0x2)
+ #define HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_LEVEL_LAST \
+ HWRM_CFA_FLOW_FLUSH_INPUT_PAGE_LEVEL_LVL_2
+ /* number of flows in the flow table */
+ uint16_t num_flows;
+ /* Pointer to the PBL, or PDL depending on number of levels */
+ uint64_t page_dir;
+} __rte_packed;
+
+/* hwrm_cfa_flow_flush_output (size:128b/16B) */
+struct hwrm_cfa_flow_flush_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_cfa_flow_stats *
+ ***********************/
+
+
+/* hwrm_cfa_flow_stats_input (size:640b/80B) */
+struct hwrm_cfa_flow_stats_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Flow handle. */
+ uint16_t num_flows;
+ /* Flow handle. */
+ uint16_t flow_handle_0;
+ /* Flow handle. */
+ uint16_t flow_handle_1;
+ /* Flow handle. */
+ uint16_t flow_handle_2;
+ /* Flow handle. */
+ uint16_t flow_handle_3;
+ /* Flow handle. */
+ uint16_t flow_handle_4;
+ /* Flow handle. */
+ uint16_t flow_handle_5;
+ /* Flow handle. */
+ uint16_t flow_handle_6;
+ /* Flow handle. */
+ uint16_t flow_handle_7;
+ /* Flow handle. */
+ uint16_t flow_handle_8;
+ /* Flow handle. */
+ uint16_t flow_handle_9;
+ uint8_t unused_0[2];
+ /* Flow ID of a flow. */
+ uint32_t flow_id_0;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_1;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_2;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_3;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_4;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_5;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_6;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_7;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_8;
+ /* Flow ID of a flow. */
+ uint32_t flow_id_9;
+} __rte_packed;
+
+/* hwrm_cfa_flow_stats_output (size:1408b/176B) */
+struct hwrm_cfa_flow_stats_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* packet_0 is 64 b */
+ uint64_t packet_0;
+ /* packet_1 is 64 b */
+ uint64_t packet_1;
+ /* packet_2 is 64 b */
+ uint64_t packet_2;
+ /* packet_3 is 64 b */
+ uint64_t packet_3;
+ /* packet_4 is 64 b */
+ uint64_t packet_4;
+ /* packet_5 is 64 b */
+ uint64_t packet_5;
+ /* packet_6 is 64 b */
+ uint64_t packet_6;
+ /* packet_7 is 64 b */
+ uint64_t packet_7;
+ /* packet_8 is 64 b */
+ uint64_t packet_8;
+ /* packet_9 is 64 b */
+ uint64_t packet_9;
+ /* byte_0 is 64 b */
+ uint64_t byte_0;
+ /* byte_1 is 64 b */
+ uint64_t byte_1;
+ /* byte_2 is 64 b */
+ uint64_t byte_2;
+ /* byte_3 is 64 b */
+ uint64_t byte_3;
+ /* byte_4 is 64 b */
+ uint64_t byte_4;
+ /* byte_5 is 64 b */
+ uint64_t byte_5;
+ /* byte_6 is 64 b */
+ uint64_t byte_6;
+ /* byte_7 is 64 b */
+ uint64_t byte_7;
+ /* byte_8 is 64 b */
+ uint64_t byte_8;
+ /* byte_9 is 64 b */
+ uint64_t byte_9;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************************
+ * hwrm_cfa_flow_aging_timer_reset *
+ ***********************************/
+
+
+/* hwrm_cfa_flow_aging_timer_reset_input (size:256b/32B) */
+struct hwrm_cfa_flow_aging_timer_reset_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Flow record index. */
+ uint16_t flow_handle;
+ uint8_t unused_0[2];
+ /*
+ * New flow timer value for the flow specified in the ext_flow_handle.
+ * The flow timer unit is 100ms.
+ */
+ uint32_t flow_timer;
+ /* This value identifies a set of CFA data structures used for a flow. */
+ uint64_t ext_flow_handle;
+} __rte_packed;
+
+/* hwrm_cfa_flow_aging_timer_reset_output (size:128b/16B) */
+struct hwrm_cfa_flow_aging_timer_reset_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_cfa_flow_aging_cfg *
+ ***************************/
+
+
+/* hwrm_cfa_flow_aging_cfg_input (size:384b/48B) */
+struct hwrm_cfa_flow_aging_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The bit field to enable per flow aging configuration. */
+ uint16_t enables;
+ /* This bit must be '1' for the tcp flow timer field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_TCP_FLOW_TIMER \
+ UINT32_C(0x1)
+ /* This bit must be '1' for the tcp finish timer field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_TCP_FIN_TIMER \
+ UINT32_C(0x2)
+ /* This bit must be '1' for the udp flow timer field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_UDP_FLOW_TIMER \
+ UINT32_C(0x4)
+ /* This bit must be '1' for the eem dma interval field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_EEM_DMA_INTERVAL \
+ UINT32_C(0x8)
+ /* This bit must be '1' for the eem notice interval field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_EEM_NOTICE_INTERVAL \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the eem context memory maximum entries field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_EEM_CTX_MAX_ENTRIES \
+ UINT32_C(0x20)
+ /* This bit must be '1' for the eem context memory ID field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_EEM_CTX_ID \
+ UINT32_C(0x40)
+ /* This bit must be '1' for the eem context memory type field to be configured */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_ENABLES_EEM_CTX_MEM_TYPE \
+ UINT32_C(0x80)
+ uint8_t flags;
+ /* Enumeration denoting the RX, TX type of the resource. */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_PATH_RX
+ /* Enumeration denoting the enable, disable eem flow aging configuration. */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_EEM UINT32_C(0x2)
+ /* tx path */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_EEM_DISABLE \
+ (UINT32_C(0x0) << 1)
+ /* rx path */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_EEM_ENABLE \
+ (UINT32_C(0x1) << 1)
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_EEM_LAST \
+ HWRM_CFA_FLOW_AGING_CFG_INPUT_FLAGS_EEM_ENABLE
+ uint8_t unused_0;
+ /* The flow aging timer for all TCP flows, the unit is 100 milliseconds. */
+ uint32_t tcp_flow_timer;
+ /* The TCP finished timer for all TCP flows, the unit is 100 milliseconds. */
+ uint32_t tcp_fin_timer;
+ /* The flow aging timer for all UDP flows, the unit is 100 milliseconds. */
+ uint32_t udp_flow_timer;
+ /* The interval to dma eem ejection data to host memory, the unit is milliseconds. */
+ uint16_t eem_dma_interval;
+ /* The interval to notify driver to read the eem ejection data, the unit is milliseconds. */
+ uint16_t eem_notice_interval;
+ /* The maximum entries number in the eem context memory. */
+ uint32_t eem_ctx_max_entries;
+ /* The context memory ID for eem flow aging. */
+ uint16_t eem_ctx_id;
+ uint16_t eem_ctx_mem_type;
+ /* The content of context memory is eem ejection data, the size of each entry is 4 bytes. */
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_EEM_CTX_MEM_TYPE_EJECTION_DATA \
+ UINT32_C(0x0)
+ #define HWRM_CFA_FLOW_AGING_CFG_INPUT_EEM_CTX_MEM_TYPE_LAST \
+ HWRM_CFA_FLOW_AGING_CFG_INPUT_EEM_CTX_MEM_TYPE_EJECTION_DATA
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_cfa_flow_aging_cfg_output (size:128b/16B) */
+struct hwrm_cfa_flow_aging_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/****************************
+ * hwrm_cfa_flow_aging_qcfg *
+ ****************************/
+
+
+/* hwrm_cfa_flow_aging_qcfg_input (size:192b/24B) */
+struct hwrm_cfa_flow_aging_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The direction for the flow aging configuration, 1 is rx path, 2 is tx path. */
+ uint8_t flags;
+ /* Enumeration denoting the RX, TX type of the resource. */
+ #define HWRM_CFA_FLOW_AGING_QCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_FLOW_AGING_QCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_FLOW_AGING_QCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_CFA_FLOW_AGING_QCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_FLOW_AGING_QCFG_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_cfa_flow_aging_qcfg_output (size:320b/40B) */
+struct hwrm_cfa_flow_aging_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The current flow aging timer for all TCP flows, the unit is 100 millisecond. */
+ uint32_t tcp_flow_timer;
+ /* The current TCP finished timer for all TCP flows, the unit is 100 millisecond. */
+ uint32_t tcp_fin_timer;
+ /* The current flow aging timer for all UDP flows, the unit is 100 millisecond. */
+ uint32_t udp_flow_timer;
+ /* The interval to dma eem ejection data to host memory, the unit is milliseconds. */
+ uint16_t eem_dma_interval;
+ /* The interval to notify driver to read the eem ejection data, the unit is milliseconds. */
+ uint16_t eem_notice_interval;
+ /* The maximum entries number in the eem context memory. */
+ uint32_t eem_ctx_max_entries;
+ /* The context memory ID for eem flow aging. */
+ uint16_t eem_ctx_id;
+ /* The context memory type for eem flow aging. */
+ uint16_t eem_ctx_mem_type;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*****************************
+ * hwrm_cfa_flow_aging_qcaps *
+ *****************************/
+
+
+/* hwrm_cfa_flow_aging_qcaps_input (size:192b/24B) */
+struct hwrm_cfa_flow_aging_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The direction for the flow aging configuration, 1 is rx path, 2 is tx path. */
+ uint8_t flags;
+ /* Enumeration denoting the RX, TX type of the resource. */
+ #define HWRM_CFA_FLOW_AGING_QCAPS_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_FLOW_AGING_QCAPS_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_CFA_FLOW_AGING_QCAPS_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_CFA_FLOW_AGING_QCAPS_INPUT_FLAGS_PATH_LAST \
+ HWRM_CFA_FLOW_AGING_QCAPS_INPUT_FLAGS_PATH_RX
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_cfa_flow_aging_qcaps_output (size:256b/32B) */
+struct hwrm_cfa_flow_aging_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The maximum flow aging timer for all TCP flows, the unit is 100 millisecond. */
+ uint32_t max_tcp_flow_timer;
+ /* The maximum TCP finished timer for all TCP flows, the unit is 100 millisecond. */
+ uint32_t max_tcp_fin_timer;
+ /* The maximum flow aging timer for all UDP flows, the unit is 100 millisecond. */
+ uint32_t max_udp_flow_timer;
+ /* The maximum aging flows that HW can support. */
+ uint32_t max_aging_flows;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************************
+ * hwrm_cfa_tcp_flag_process_qcfg *
+ **********************************/
+
+
+/* hwrm_cfa_tcp_flag_process_qcfg_input (size:128b/16B) */
+struct hwrm_cfa_tcp_flag_process_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_cfa_tcp_flag_process_qcfg_output (size:192b/24B) */
+struct hwrm_cfa_tcp_flag_process_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The port 0 RX mirror action record ID. */
+ uint16_t rx_ar_id_port0;
+ /* The port 1 RX mirror action record ID. */
+ uint16_t rx_ar_id_port1;
+ /* The port 0 RX action record ID for TX TCP flag packets from loopback path. */
+ uint16_t tx_ar_id_port0;
+ /* The port 1 RX action record ID for TX TCP flag packets from loopback path. */
+ uint16_t tx_ar_id_port1;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_cfa_vf_pair_alloc *
+ **************************/
+
+
+/* hwrm_cfa_vf_pair_alloc_input (size:448b/56B) */
+struct hwrm_cfa_vf_pair_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_a_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_b_id;
+ uint8_t unused_0[4];
+ /* VF Pair name (32 byte string). */
+ char pair_name[32];
+} __rte_packed;
+
+/* hwrm_cfa_vf_pair_alloc_output (size:128b/16B) */
+struct hwrm_cfa_vf_pair_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_cfa_vf_pair_free *
+ *************************/
+
+
+/* hwrm_cfa_vf_pair_free_input (size:384b/48B) */
+struct hwrm_cfa_vf_pair_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* VF Pair name (32 byte string). */
+ char pair_name[32];
+} __rte_packed;
+
+/* hwrm_cfa_vf_pair_free_output (size:128b/16B) */
+struct hwrm_cfa_vf_pair_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_cfa_vf_pair_info *
+ *************************/
+
+
+/* hwrm_cfa_vf_pair_info_input (size:448b/56B) */
+struct hwrm_cfa_vf_pair_info_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* If this flag is set, lookup by name else lookup by index. */
+ #define HWRM_CFA_VF_PAIR_INFO_INPUT_FLAGS_LOOKUP_TYPE UINT32_C(0x1)
+ /* vf pair table index. */
+ uint16_t vf_pair_index;
+ uint8_t unused_0[2];
+ /* VF Pair name (32 byte string). */
+ char vf_pair_name[32];
+} __rte_packed;
+
+/* hwrm_cfa_vf_pair_info_output (size:512b/64B) */
+struct hwrm_cfa_vf_pair_info_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* vf pair table index. */
+ uint16_t next_vf_pair_index;
+ /* vf pair member a's vf_fid. */
+ uint16_t vf_a_fid;
+ /* vf pair member a's Linux logical VF number. */
+ uint16_t vf_a_index;
+ /* vf pair member b's vf_fid. */
+ uint16_t vf_b_fid;
+ /* vf pair member a's Linux logical VF number. */
+ uint16_t vf_b_index;
+ /* vf pair state. */
+ uint8_t pair_state;
+ /* Pair has been allocated */
+ #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ALLOCATED UINT32_C(0x1)
+ /* Both pair members are active */
+ #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE UINT32_C(0x2)
+ #define HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_LAST \
+ HWRM_CFA_VF_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE
+ uint8_t unused_0[5];
+ /* VF Pair name (32 byte string). */
+ char pair_name[32];
+ uint8_t unused_1[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_cfa_pair_alloc *
+ ***********************/
+
+
+/* hwrm_cfa_pair_alloc_input (size:576b/72B) */
+struct hwrm_cfa_pair_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair,
+ * 5-rep2fn_mod, 6-rep2fn_modall, 7-rep2fn_truflow).
+ */
+ uint16_t pair_mode;
+ /* Pair between VF on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_VF2FN \
+ UINT32_C(0x0)
+ /* Pair between REP on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN \
+ UINT32_C(0x1)
+ /* Pair between REP on local host with REP on specified host. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2REP \
+ UINT32_C(0x2)
+ /* Pair for the proxy interface. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_PROXY \
+ UINT32_C(0x3)
+ /* Pair for the PF interface. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_PFPAIR \
+ UINT32_C(0x4)
+ /* Modify existing rep2fn pair and move pair to new PF. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_MOD \
+ UINT32_C(0x5)
+ /* Modify existing rep2fn pairs paired with same PF and move pairs to new PF. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_MODALL \
+ UINT32_C(0x6)
+ /* Truflow pair between REP on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_TRUFLOW \
+ UINT32_C(0x7)
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_LAST \
+ HWRM_CFA_PAIR_ALLOC_INPUT_PAIR_MODE_REP2FN_TRUFLOW
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_a_id;
+ /* Logical Host (0xff-local host). */
+ uint8_t host_b_id;
+ /* Logical PF (0xff-PF for command channel). */
+ uint8_t pf_b_id;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_b_id;
+ /* Loopback port (0xff-internal loopback), valid for mode-3. */
+ uint8_t port_id;
+ /* Priority used for encap of loopback packets valid for mode-3. */
+ uint8_t pri;
+ /* New PF for rep2fn modify, valid for mode 5. */
+ uint16_t new_pf_fid;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the q_ab field to be
+ * configured.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_Q_AB_VALID UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the q_ba field to be
+ * configured.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_Q_BA_VALID UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the fc_ab field to be
+ * configured.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_FC_AB_VALID UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the fc_ba field to be
+ * configured.
+ */
+ #define HWRM_CFA_PAIR_ALLOC_INPUT_ENABLES_FC_BA_VALID UINT32_C(0x8)
+ /* VF Pair name (32 byte string). */
+ char pair_name[32];
+ /*
+ * The q_ab value specifies the logical index of the TX/RX CoS
+ * queue to be assigned for traffic in the A to B direction of
+ * the interface pair. The default value is 0.
+ */
+ uint8_t q_ab;
+ /*
+ * The q_ba value specifies the logical index of the TX/RX CoS
+ * queue to be assigned for traffic in the B to A direction of
+ * the interface pair. The default value is 1.
+ */
+ uint8_t q_ba;
+ /*
+ * Specifies whether RX ring flow control is disabled (0) or enabled
+ * (1) in the A to B direction. The default value is 0, meaning that
+ * packets will be dropped when the B-side RX rings are full.
+ */
+ uint8_t fc_ab;
+ /*
+ * Specifies whether RX ring flow control is disabled (0) or enabled
+ * (1) in the B to A direction. The default value is 1, meaning that
+ * the RX CoS queue will be flow controlled when the A-side RX rings
+ * are full.
+ */
+ uint8_t fc_ba;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_cfa_pair_alloc_output (size:192b/24B) */
+struct hwrm_cfa_pair_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Only valid for modes 1 and 2. */
+ uint16_t rx_cfa_code_a;
+ /* Only valid for modes 1 and 2. */
+ uint16_t tx_cfa_action_a;
+ /* Only valid for mode 2. */
+ uint16_t rx_cfa_code_b;
+ /* Only valid for mode 2. */
+ uint16_t tx_cfa_action_b;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_cfa_pair_free *
+ **********************/
+
+
+/* hwrm_cfa_pair_free_input (size:448b/56B) */
+struct hwrm_cfa_pair_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* VF Pair name (32 byte string). */
+ char pair_name[32];
+ /* Logical PF (0xff-PF for command channel). */
+ uint8_t pf_b_id;
+ uint8_t unused_0[3];
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_id;
+ /*
+ * Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair,
+ * 5-rep2fn_mod, 6-rep2fn_modall, 7-rep2fn_truflow).
+ */
+ uint16_t pair_mode;
+ /* Pair between VF on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_VF2FN UINT32_C(0x0)
+ /* Pair between REP on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_REP2FN UINT32_C(0x1)
+ /* Pair between REP on local host with REP on specified host. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_REP2REP UINT32_C(0x2)
+ /* Pair for the proxy interface. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_PROXY UINT32_C(0x3)
+ /* Pair for the PF interface. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_PFPAIR UINT32_C(0x4)
+ /* Modify existing rep2fn pair and move pair to new PF. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_REP2FN_MOD UINT32_C(0x5)
+ /* Modify existing rep2fn pairs paired with same PF and move pairs to new PF. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_REP2FN_MODALL UINT32_C(0x6)
+ /* Truflow pair between REP on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_REP2FN_TRUFLOW UINT32_C(0x7)
+ #define HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_LAST \
+ HWRM_CFA_PAIR_FREE_INPUT_PAIR_MODE_REP2FN_TRUFLOW
+} __rte_packed;
+
+/* hwrm_cfa_pair_free_output (size:128b/16B) */
+struct hwrm_cfa_pair_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_cfa_pair_info *
+ **********************/
+
+
+/* hwrm_cfa_pair_info_input (size:448b/56B) */
+struct hwrm_cfa_pair_info_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* If this flag is set, lookup by name else lookup by index. */
+ #define HWRM_CFA_PAIR_INFO_INPUT_FLAGS_LOOKUP_TYPE UINT32_C(0x1)
+ /* If this flag is set, lookup by PF id and VF id. */
+ #define HWRM_CFA_PAIR_INFO_INPUT_FLAGS_LOOKUP_REPRE UINT32_C(0x2)
+ /* Pair table index. */
+ uint16_t pair_index;
+ /* Pair pf index. */
+ uint8_t pair_pfid;
+ /* Pair vf index. */
+ uint8_t pair_vfid;
+ /* Pair name (32 byte string). */
+ char pair_name[32];
+} __rte_packed;
+
+/* hwrm_cfa_pair_info_output (size:576b/72B) */
+struct hwrm_cfa_pair_info_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Pair table index. */
+ uint16_t next_pair_index;
+ /* Pair member a's fid. */
+ uint16_t a_fid;
+ /* Logical host number. */
+ uint8_t host_a_index;
+ /* Logical PF number. */
+ uint8_t pf_a_index;
+ /* Pair member a's Linux logical VF number. */
+ uint16_t vf_a_index;
+ /* Rx CFA code. */
+ uint16_t rx_cfa_code_a;
+ /* Tx CFA action. */
+ uint16_t tx_cfa_action_a;
+ /* Pair member b's fid. */
+ uint16_t b_fid;
+ /* Logical host number. */
+ uint8_t host_b_index;
+ /* Logical PF number. */
+ uint8_t pf_b_index;
+ /* Pair member a's Linux logical VF number. */
+ uint16_t vf_b_index;
+ /* Rx CFA code. */
+ uint16_t rx_cfa_code_b;
+ /* Tx CFA action. */
+ uint16_t tx_cfa_action_b;
+ /* Pair mode (0-vf2fn, 1-rep2fn, 2-rep2rep, 3-proxy, 4-pfpair). */
+ uint8_t pair_mode;
+ /* Pair between VF on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_VF2FN UINT32_C(0x0)
+ /* Pair between REP on local host with PF or VF on specified host. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_REP2FN UINT32_C(0x1)
+ /* Pair between REP on local host with REP on specified host. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_REP2REP UINT32_C(0x2)
+ /* Pair for the proxy interface. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PROXY UINT32_C(0x3)
+ /* Pair for the PF interface. */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PFPAIR UINT32_C(0x4)
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_LAST \
+ HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_MODE_PFPAIR
+ /* Pair state. */
+ uint8_t pair_state;
+ /* Pair has been allocated */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ALLOCATED UINT32_C(0x1)
+ /* Both pair members are active */
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE UINT32_C(0x2)
+ #define HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_LAST \
+ HWRM_CFA_PAIR_INFO_OUTPUT_PAIR_STATE_ACTIVE
+ /* Pair name (32 byte string). */
+ char pair_name[32];
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_cfa_vfr_alloc *
+ **********************/
+
+
+/* hwrm_cfa_vfr_alloc_input (size:448b/56B) */
+struct hwrm_cfa_vfr_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_id;
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint16_t reserved;
+ uint8_t unused_0[4];
+ /* VF Representor name (32 byte string). */
+ char vfr_name[32];
+} __rte_packed;
+
+/* hwrm_cfa_vfr_alloc_output (size:128b/16B) */
+struct hwrm_cfa_vfr_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Rx CFA code. */
+ uint16_t rx_cfa_code;
+ /* Tx CFA action. */
+ uint16_t tx_cfa_action;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************
+ * hwrm_cfa_vfr_free *
+ *********************/
+
+
+/* hwrm_cfa_vfr_free_input (size:448b/56B) */
+struct hwrm_cfa_vfr_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* VF Representor name (32 byte string). */
+ char vfr_name[32];
+ /* Logical VF number (range: 0 -> MAX_VFS -1). */
+ uint16_t vf_id;
+ /*
+ * This field is reserved for the future use.
+ * It shall be set to 0.
+ */
+ uint16_t reserved;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/* hwrm_cfa_vfr_free_output (size:128b/16B) */
+struct hwrm_cfa_vfr_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************************
+ * hwrm_cfa_redirect_query_tunnel_type *
+ ***************************************/
+
+
+/* hwrm_cfa_redirect_query_tunnel_type_input (size:192b/24B) */
+struct hwrm_cfa_redirect_query_tunnel_type_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The source function id. */
+ uint16_t src_fid;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_cfa_redirect_query_tunnel_type_output (size:128b/16B) */
+struct hwrm_cfa_redirect_query_tunnel_type_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Tunnel Mask. */
+ uint32_t tunnel_mask;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_NONTUNNEL \
+ UINT32_C(0x1)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_VXLAN \
+ UINT32_C(0x2)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_NVGRE \
+ UINT32_C(0x4)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_L2GRE \
+ UINT32_C(0x8)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_IPIP \
+ UINT32_C(0x10)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_GENEVE \
+ UINT32_C(0x20)
+ /* Multi-Protocol Label Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_MPLS \
+ UINT32_C(0x40)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_STT \
+ UINT32_C(0x80)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_IPGRE \
+ UINT32_C(0x100)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_VXLAN_V4 \
+ UINT32_C(0x200)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_IPGRE_V1 \
+ UINT32_C(0x400)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_ANYTUNNEL \
+ UINT32_C(0x800)
+ /* Use fixed layer 2 ether type of 0xFFFF */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_L2_ETYPE \
+ UINT32_C(0x1000)
+ /* IPV6 over virtual eXtensible Local Area Network with GPE header (IPV6oVXLANGPE) */
+ #define HWRM_CFA_REDIRECT_QUERY_TUNNEL_TYPE_OUTPUT_TUNNEL_MASK_VXLAN_GPE_V6 \
+ UINT32_C(0x2000)
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_cfa_ctx_mem_rgtr *
+ *************************/
+
+
+/* hwrm_cfa_ctx_mem_rgtr_input (size:256b/32B) */
+struct hwrm_cfa_ctx_mem_rgtr_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint16_t flags;
+ /* Counter PBL indirect levels. */
+ uint8_t page_level;
+ /* PBL pointer is physical start address. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_LEVEL_LVL_0 UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_LEVEL_LVL_1 UINT32_C(0x1)
+ /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_LEVEL_LVL_2 UINT32_C(0x2)
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_LEVEL_LAST \
+ HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_LEVEL_LVL_2
+ /* Page size. */
+ uint8_t page_size;
+ /* 4KB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_4K UINT32_C(0x0)
+ /* 8KB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_8K UINT32_C(0x1)
+ /* 64KB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_64K UINT32_C(0x4)
+ /* 256KB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_256K UINT32_C(0x6)
+ /* 1MB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_1M UINT32_C(0x8)
+ /* 2MB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_2M UINT32_C(0x9)
+ /* 4MB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_4M UINT32_C(0xa)
+ /* 1GB page size. */
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_1G UINT32_C(0x12)
+ #define HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_LAST \
+ HWRM_CFA_CTX_MEM_RGTR_INPUT_PAGE_SIZE_1G
+ uint32_t unused_0;
+ /* Pointer to the PBL, or PDL depending on number of levels */
+ uint64_t page_dir;
+} __rte_packed;
+
+/* hwrm_cfa_ctx_mem_rgtr_output (size:128b/16B) */
+struct hwrm_cfa_ctx_mem_rgtr_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * Id/Handle to the recently register context memory. This handle is passed
+ * to the CFA feature.
+ */
+ uint16_t ctx_id;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_cfa_ctx_mem_unrgtr *
+ ***************************/
+
+
+/* hwrm_cfa_ctx_mem_unrgtr_input (size:192b/24B) */
+struct hwrm_cfa_ctx_mem_unrgtr_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Id/Handle to the recently register context memory. This handle is passed
+ * to the CFA feature.
+ */
+ uint16_t ctx_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_cfa_ctx_mem_unrgtr_output (size:128b/16B) */
+struct hwrm_cfa_ctx_mem_unrgtr_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_cfa_ctx_mem_qctx *
+ *************************/
+
+
+/* hwrm_cfa_ctx_mem_qctx_input (size:192b/24B) */
+struct hwrm_cfa_ctx_mem_qctx_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Id/Handle to the recently register context memory. This handle is passed
+ * to the CFA feature.
+ */
+ uint16_t ctx_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_cfa_ctx_mem_qctx_output (size:256b/32B) */
+struct hwrm_cfa_ctx_mem_qctx_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint16_t flags;
+ /* Counter PBL indirect levels. */
+ uint8_t page_level;
+ /* PBL pointer is physical start address. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_LEVEL_LVL_0 UINT32_C(0x0)
+ /* PBL pointer points to PTE table. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_LEVEL_LVL_1 UINT32_C(0x1)
+ /* PBL pointer points to PDE table with each entry pointing to PTE tables. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_LEVEL_LVL_2 UINT32_C(0x2)
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_LEVEL_LAST \
+ HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_LEVEL_LVL_2
+ /* Page size. */
+ uint8_t page_size;
+ /* 4KB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_4K UINT32_C(0x0)
+ /* 8KB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_8K UINT32_C(0x1)
+ /* 64KB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_64K UINT32_C(0x4)
+ /* 256KB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_256K UINT32_C(0x6)
+ /* 1MB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_1M UINT32_C(0x8)
+ /* 2MB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_2M UINT32_C(0x9)
+ /* 4MB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_4M UINT32_C(0xa)
+ /* 1GB page size. */
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_1G UINT32_C(0x12)
+ #define HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_LAST \
+ HWRM_CFA_CTX_MEM_QCTX_OUTPUT_PAGE_SIZE_1G
+ uint8_t unused_0[4];
+ /* Pointer to the PBL, or PDL depending on number of levels */
+ uint64_t page_dir;
+ uint8_t unused_1[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_cfa_ctx_mem_qcaps *
+ **************************/
+
+
+/* hwrm_cfa_ctx_mem_qcaps_input (size:128b/16B) */
+struct hwrm_cfa_ctx_mem_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_cfa_ctx_mem_qcaps_output (size:128b/16B) */
+struct hwrm_cfa_ctx_mem_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Indicates the maximum number of context memory which can be registered. */
+ uint16_t max_entries;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_cfa_counter_qcaps *
+ **************************/
+
+
+/* hwrm_cfa_counter_qcaps_input (size:128b/16B) */
+struct hwrm_cfa_counter_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_cfa_counter_qcaps_output (size:576b/72B) */
+struct hwrm_cfa_counter_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t flags;
+ /* Enumeration denoting the supported CFA counter format. */
+ #define HWRM_CFA_COUNTER_QCAPS_OUTPUT_FLAGS_COUNTER_FORMAT \
+ UINT32_C(0x1)
+ /* CFA counter types are not supported. */
+ #define HWRM_CFA_COUNTER_QCAPS_OUTPUT_FLAGS_COUNTER_FORMAT_NONE \
+ UINT32_C(0x0)
+ /* 64-bit packet counters followed by 64-bit byte counters format. */
+ #define HWRM_CFA_COUNTER_QCAPS_OUTPUT_FLAGS_COUNTER_FORMAT_64_BIT \