+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
+ UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for autoneg mode. This mode has
+ * been DEPRECATED. An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
+ UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below that speed for autoneg.
+ * This mode has been DEPRECATED. An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
+ UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding link speed mask value
+ * that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
+ UINT32_C(0x4)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_LAST \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK
+ /* The advertised pause settings on the port by the link partner. */
+ uint8_t link_partner_adv_pause;
+ /*
+ * When this bit is '1', Generation of tx pause messages
+ * is supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages
+ * is supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
+ UINT32_C(0x2)
+ /*
+ * Current setting for link speed mask that is used to
+ * advertise speeds during autonegotiation when EEE is enabled.
+ * This field is valid only when eee_enabled flags is set to 1.
+ * The speeds specified in this field shall be a subset of
+ * speeds specified in auto_link_speed_mask.
+ */
+ uint16_t adv_eee_link_speed_mask;
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ /*
+ * Current setting for link speed mask that is advertised by
+ * the link partner when EEE is enabled.
+ * This field is valid only when eee_enabled flags is set to 1.
+ */
+ uint16_t link_partner_adv_eee_link_speed_mask;
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint32_t xcvr_identifier_type_tx_lpi_timer;
+ /*
+ * Current setting of TX LPI timer in microseconds.
+ * This field is valid only when_eee_enabled flag is set to 1
+ * and tx_lpi_enabled is set to 1.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK \
+ UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
+ /* This value represents transceiver identifier type. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT 24
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 24)
+ /* SFP/SFP+/SFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
+ (UINT32_C(0x3) << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
+ (UINT32_C(0xc) << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
+ (UINT32_C(0xd) << 24)
+ /* QSFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
+ (UINT32_C(0x11) << 24)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_LAST \
+ HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28
+ /*
+ * This value represents the current configuration of
+ * Forward Error Correction (FEC) on the port.
+ */
+ uint16_t fec_cfg;
+ /*
+ * When set to 1, then FEC is not supported on this port. If this flag
+ * is set to 1, then all other FEC configuration flags shall be ignored.
+ * When set to 0, then FEC is supported as indicated by other
+ * configuration flags.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * When set to 1, then FEC autonegotiation is supported on this port.
+ * When set to 0, then FEC autonegotiation is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * When set to 1, then FEC autonegotiation is enabled on this port.
+ * When set to 0, then FEC autonegotiation is disabled if supported.
+ * This flag should be ignored if FEC autonegotiation is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED \
+ UINT32_C(0x4)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on this port.
+ * When set to 0, then FEC CLAUSE 74 (Fire Code) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on this
+ * port. This means that FEC CLAUSE 74 is either advertised if
+ * FEC autonegotiation is enabled or FEC CLAUSE 74 is force enabled.
+ * When set to 0, then FEC CLAUSE 74 (Fire Code) is disabled if supported.
+ * This flag should be ignored if FEC CLAUSE 74 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED \
+ UINT32_C(0x10)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon RS(528,514) for
+ * NRZ) is supported on this port.
+ * When set to 0, then FEC RS(528,418) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon RS(528,514) for
+ * NRZ) is enabled on this port. This means that FEC RS(528,514) is
+ * either advertised if FEC autonegotiation is enabled or FEC
+ * RS(528,514) is force enabled. When set to 0, then FEC RS(528,514)
+ * is disabled if supported.
+ * This flag should be ignored if FEC CLAUSE 91 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED \
+ UINT32_C(0x40)
+ /*
+ * When set to 1, then FEC RS544_1XN is supported on this port.
+ * When set to 0, then FEC RS544_1XN is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS544_1XN_SUPPORTED \
+ UINT32_C(0x80)
+ /*
+ * When set to 1, then RS544_1XN is enabled on this
+ * port. This means that FEC RS544_1XN is either advertised if
+ * FEC autonegotiation is enabled or FEC RS544_1XN is force enabled.
+ * When set to 0, then FEC RS544_1XN is disabled if supported.
+ * This flag should be ignored if FEC RS544_1XN is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS544_1XN_ENABLED \
+ UINT32_C(0x100)
+ /*
+ * When set to 1, then FEC RS(544,514) is supported on this port.
+ * When set to 0, then FEC RS(544,514) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS544_IEEE_SUPPORTED \
+ UINT32_C(0x200)
+ /*
+ * When set to 1, then RS(544,514) is enabled on this
+ * port. This means that FEC RS(544,514) is either advertised if
+ * FEC autonegotiation is enabled or FEC RS(544,514) is force
+ * enabled. When set to 0, then FEC RS(544,514) is disabled if supported.
+ * This flag should be ignored if FEC RS(544,514) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS544_IEEE_ENABLED \
+ UINT32_C(0x400)
+ /*
+ * When set to 1, then FEC RS272_1XN is supported on this port.
+ * When set to 0, then FEC RS272_1XN is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS272_1XN_SUPPORTED \
+ UINT32_C(0x800)
+ /*
+ * When set to 1, then RS272_1XN is enabled on this
+ * port. This means that FEC RS272_1XN is either advertised if
+ * FEC autonegotiation is enabled or FEC RS272_1XN is force
+ * enabled. When set to 0, then FEC RS272_1XN is disabled if supported.
+ * This flag should be ignored if FEC RS272_1XN is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS272_1XN_ENABLED \
+ UINT32_C(0x1000)
+ /*
+ * When set to 1, then FEC RS(272,514) is supported on this port.
+ * When set to 0, then FEC RS(272,514) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS272_IEEE_SUPPORTED \
+ UINT32_C(0x2000)
+ /*
+ * When set to 1, then RS(272,257) is enabled on this
+ * port. This means that FEC RS(272,257) is either advertised if
+ * FEC autonegotiation is enabled or FEC RS(272,257) is force
+ * enabled. When set to 0, then FEC RS(272,257) is disabled if supported.
+ * This flag should be ignored if FEC RS(272,257) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_RS272_IEEE_ENABLED \
+ UINT32_C(0x4000)
+ /*
+ * This value is indicates the duplex of the current
+ * connection state.
+ */
+ uint8_t duplex_state;
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_HALF UINT32_C(0x0)
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_FULL UINT32_C(0x1)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_LAST \
+ HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_FULL
+ /* Option flags fields. */
+ uint8_t option_flags;
+ /* When this bit is '1', Media auto detect is enabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_OPTION_FLAGS_MEDIA_AUTO_DETECT \
+ UINT32_C(0x1)
+ /*
+ * Up to 16 bytes of null padded ASCII string representing
+ * PHY vendor.
+ * If the string is set to null, then the vendor name is not
+ * available.
+ */
+ char phy_vendor_name[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string that
+ * identifies vendor specific part number of the PHY.
+ * If the string is set to null, then the vendor specific
+ * part number is not available.
+ */
+ char phy_vendor_partnumber[16];
+ /*
+ * The supported PAM4 speeds for the port. This is a bit mask.
+ * For each speed that is supported, the corresponding
+ * bit will be set to '1'.
+ */
+ uint16_t support_pam4_speeds;
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_PAM4_SPEEDS_50G \
+ UINT32_C(0x1)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_PAM4_SPEEDS_100G \
+ UINT32_C(0x2)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_PAM4_SPEEDS_200G \
+ UINT32_C(0x4)
+ /*
+ * Current setting of forced PAM4 link speed.
+ * When the link speed is not being forced, this
+ * value shall be set to 0.
+ */
+ uint16_t force_pam4_link_speed;
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAM4_LINK_SPEED_50GB \
+ UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAM4_LINK_SPEED_100GB \
+ UINT32_C(0x3e8)
+ /* 200Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAM4_LINK_SPEED_200GB \
+ UINT32_C(0x7d0)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAM4_LINK_SPEED_LAST \
+ HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAM4_LINK_SPEED_200GB
+ /*
+ * Current setting for auto_pam4_link_speed_mask that is used to
+ * advertise speeds during autonegotiation.
+ * This field is only valid when auto_mode is set to "mask".
+ * The speeds specified in this field shall be a subset of
+ * supported speeds on this port.
+ */
+ uint16_t auto_pam4_link_speed_mask;
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAM4_LINK_SPEED_MASK_50G \
+ UINT32_C(0x1)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAM4_LINK_SPEED_MASK_100G \
+ UINT32_C(0x2)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAM4_LINK_SPEED_MASK_200G \
+ UINT32_C(0x4)
+ /*
+ * The advertised PAM4 speeds for the port by the link partner.
+ * Each advertised speed will be set to '1'.
+ */
+ uint8_t link_partner_pam4_adv_speeds;
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_PAM4_ADV_SPEEDS_50GB \
+ UINT32_C(0x1)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_PAM4_ADV_SPEEDS_100GB \
+ UINT32_C(0x2)
+ /* 200Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_PAM4_ADV_SPEEDS_200GB \
+ UINT32_C(0x4)
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************
+ * hwrm_port_mac_cfg *
+ *********************/
+
+
+/* hwrm_port_mac_cfg_input (size:384b/48B) */
+struct hwrm_port_mac_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * In this field, there are a number of CoS mappings related flags
+ * that are used to configure CoS mappings and their corresponding
+ * priorities in the hardware.
+ * For the priorities of CoS mappings, the HWRM uses the following
+ * priority order (high to low) by default:
+ * # vlan pri
+ * # ip_dscp
+ * # tunnel_vlan_pri
+ * # default cos
+ *
+ * A subset of CoS mappings can be enabled.
+ * If a priority is not specified for an enabled CoS mapping, the
+ * priority will be assigned in the above order for the enabled CoS
+ * mappings. For example, if vlan_pri and ip_dscp CoS mappings are
+ * enabled and their priorities are not specified, the following
+ * priority order (high to low) will be used by the HWRM:
+ * # vlan_pri
+ * # ip_dscp
+ * # default cos
+ *
+ * vlan_pri CoS mapping together with default CoS with lower priority
+ * are enabled by default by the HWRM.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', this command will configure
+ * the MAC to match the current link state of the PHY.
+ * If the link is not established on the PHY, then this
+ * bit has no effect.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_MATCH_LINK \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', the inner VLAN PRI to CoS mapping
+ * is requested to be enabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_VLAN_PRI2COS_ENABLE \
+ UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', tunnel VLAN PRI field to
+ * CoS mapping is requested to be enabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_TUNNEL_PRI2COS_ENABLE \
+ UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', the IP DSCP to CoS mapping is
+ * requested to be enabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_IP_DSCP2COS_ENABLE \
+ UINT32_C(0x8)
+ /*
+ * When this bit is '1', the HWRM is requested to
+ * enable timestamp capture capability on the receive side
+ * of this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_RX_TS_CAPTURE_ENABLE \
+ UINT32_C(0x10)
+ /*
+ * When this bit is '1', the HWRM is requested to
+ * disable timestamp capture capability on the receive side
+ * of this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_RX_TS_CAPTURE_DISABLE \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1', the HWRM is requested to
+ * enable timestamp capture capability on the transmit side
+ * of this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_TX_TS_CAPTURE_ENABLE \
+ UINT32_C(0x40)
+ /*
+ * When this bit is '1', the HWRM is requested to
+ * disable timestamp capture capability on the transmit side
+ * of this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_TX_TS_CAPTURE_DISABLE \
+ UINT32_C(0x80)
+ /*
+ * When this bit is '1', the Out-Of-Box WoL is requested to
+ * be enabled on this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_OOB_WOL_ENABLE \
+ UINT32_C(0x100)
+ /*
+ * When this bit is '1', the Out-Of-Box WoL is requested to
+ * be disabled on this port.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_OOB_WOL_DISABLE \
+ UINT32_C(0x200)
+ /*
+ * When this bit is set to '1', the inner VLAN PRI to CoS mapping
+ * is requested to be disabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_VLAN_PRI2COS_DISABLE \
+ UINT32_C(0x400)
+ /*
+ * When this bit is set to '1', tunnel VLAN PRI field to
+ * CoS mapping is requested to be disabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_TUNNEL_PRI2COS_DISABLE \
+ UINT32_C(0x800)
+ /*
+ * When this bit is set to '1', the IP DSCP to CoS mapping is
+ * requested to be disabled.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_IP_DSCP2COS_DISABLE \
+ UINT32_C(0x1000)
+ /*
+ * When this bit is set to '1', and the ptp_tx_ts_capture_enable
+ * bit is set, then the device uses one step Tx timestamping.
+ * This bit is temporary and used for experimental purposes.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_FLAGS_PTP_ONE_STEP_TX_TS \
+ UINT32_C(0x2000)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the ipg field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_IPG \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the lpbk field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_LPBK \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the vlan_pri2cos_map_pri field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_VLAN_PRI2COS_MAP_PRI \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the tunnel_pri2cos_map_pri field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_TUNNEL_PRI2COS_MAP_PRI \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the dscp2cos_map_pri field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_DSCP2COS_MAP_PRI \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the rx_ts_capture_ptp_msg_type field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_RX_TS_CAPTURE_PTP_MSG_TYPE \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the tx_ts_capture_ptp_msg_type field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_TX_TS_CAPTURE_PTP_MSG_TYPE \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the cos_field_cfg field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_COS_FIELD_CFG \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the ptp_freq_adj_ppb field to be
+ * configured.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_ENABLES_PTP_FREQ_ADJ_PPB \
+ UINT32_C(0x200)
+ /* Port ID of port that is to be configured. */
+ uint16_t port_id;
+ /*
+ * This value is used to configure the minimum IPG that will
+ * be sent between packets by this port.
+ */
+ uint8_t ipg;
+ /* This value controls the loopback setting for the MAC. */
+ uint8_t lpbk;
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback such that
+ * host data is sent back to the host without modification.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote loopback such that
+ * port logic will send packets back out the transmitter that
+ * are received.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_REMOTE UINT32_C(0x2)
+ #define HWRM_PORT_MAC_CFG_INPUT_LPBK_LAST \
+ HWRM_PORT_MAC_CFG_INPUT_LPBK_REMOTE
+ /*
+ * This value controls the priority setting of VLAN PRI to CoS
+ * mapping based on VLAN Tags of inner packet headers of
+ * tunneled packets or packet headers of non-tunneled packets.
+ *
+ * # Each XXX_pri variable shall have a unique priority value
+ * when it is being specified.
+ * # When comparing priorities of mappings, higher value
+ * indicates higher priority.
+ * For example, a value of 0-3 is returned where 0 is being
+ * the lowest priority and 3 is being the highest priority.
+ */
+ uint8_t vlan_pri2cos_map_pri;
+ /* Reserved field. */
+ uint8_t reserved1;
+ /*
+ * This value controls the priority setting of VLAN PRI to CoS
+ * mapping based on VLAN Tags of tunneled header.
+ * This mapping only applies when tunneled headers
+ * are present.
+ *
+ * # Each XXX_pri variable shall have a unique priority value
+ * when it is being specified.
+ * # When comparing priorities of mappings, higher value
+ * indicates higher priority.
+ * For example, a value of 0-3 is returned where 0 is being
+ * the lowest priority and 3 is being the highest priority.
+ */
+ uint8_t tunnel_pri2cos_map_pri;
+ /*
+ * This value controls the priority setting of IP DSCP to CoS
+ * mapping based on inner IP header of tunneled packets or
+ * IP header of non-tunneled packets.
+ *
+ * # Each XXX_pri variable shall have a unique priority value
+ * when it is being specified.
+ * # When comparing priorities of mappings, higher value
+ * indicates higher priority.
+ * For example, a value of 0-3 is returned where 0 is being
+ * the lowest priority and 3 is being the highest priority.
+ */
+ uint8_t dscp2pri_map_pri;
+ /*
+ * This is a 16-bit bit mask that is used to request a
+ * specific configuration of time stamp capture of PTP messages
+ * on the receive side of this port.
+ * This field shall be ignored if the ptp_rx_ts_capture_enable
+ * flag is not set in this command.
+ * Otherwise, if bit 'i' is set, then the HWRM is being
+ * requested to configure the receive side of the port to
+ * capture the time stamp of every received PTP message
+ * with messageType field value set to i.
+ */
+ uint16_t rx_ts_capture_ptp_msg_type;
+ /*
+ * This is a 16-bit bit mask that is used to request a
+ * specific configuration of time stamp capture of PTP messages
+ * on the transmit side of this port.
+ * This field shall be ignored if the ptp_tx_ts_capture_enable
+ * flag is not set in this command.
+ * Otherwise, if bit 'i' is set, then the HWRM is being
+ * requested to configure the transmit side of the port to
+ * capture the time stamp of every transmitted PTP message
+ * with messageType field value set to i.
+ */
+ uint16_t tx_ts_capture_ptp_msg_type;
+ /* Configuration of CoS fields. */
+ uint8_t cos_field_cfg;
+ /* Reserved */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_RSVD1 \
+ UINT32_C(0x1)
+ /*
+ * This field is used to specify selection of VLAN PRI value
+ * based on whether one or two VLAN Tags are present in
+ * the inner packet headers of tunneled packets or
+ * non-tunneled packets.
+ * This field is valid only if inner VLAN PRI to CoS mapping
+ * is enabled.
+ * If VLAN PRI to CoS mapping is not enabled, then this
+ * field shall be ignored.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_MASK \
+ UINT32_C(0x6)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_SFT \
+ 1
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags are
+ * present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_INNERMOST \
+ (UINT32_C(0x0) << 1)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags are
+ * present in the inner packet headers.
+ * No VLAN PRI shall be selected for this configuration
+ * if only one VLAN Tag is present in the inner
+ * packet headers.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTER \
+ (UINT32_C(0x1) << 1)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTERMOST \
+ (UINT32_C(0x2) << 1)
+ /* Unspecified */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED \
+ (UINT32_C(0x3) << 1)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_LAST \
+ HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field is used to specify selection of tunnel VLAN
+ * PRI value based on whether one or two VLAN Tags are
+ * present in tunnel headers.
+ * This field is valid only if tunnel VLAN PRI to CoS mapping
+ * is enabled.
+ * If tunnel VLAN PRI to CoS mapping is not enabled, then this
+ * field shall be ignored.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_MASK \
+ UINT32_C(0x18)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_SFT \
+ 3
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags are
+ * present in the tunnel packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_INNERMOST \
+ (UINT32_C(0x0) << 3)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags are
+ * present in the tunnel packet headers.
+ * No tunnel VLAN PRI shall be selected for this
+ * configuration if only one VLAN Tag is present in
+ * the tunnel packet headers.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTER \
+ (UINT32_C(0x1) << 3)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the tunnel packet headers
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTERMOST \
+ (UINT32_C(0x2) << 3)
+ /* Unspecified */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED \
+ (UINT32_C(0x3) << 3)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_LAST \
+ HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field shall be used to provide default CoS value
+ * that has been configured on this port.
+ * This field is valid only if default CoS mapping
+ * is enabled.
+ * If default CoS mapping is not enabled, then this
+ * field shall be ignored.
+ */
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_DEFAULT_COS_MASK \
+ UINT32_C(0xe0)
+ #define HWRM_PORT_MAC_CFG_INPUT_COS_FIELD_CFG_DEFAULT_COS_SFT \
+ 5
+ uint8_t unused_0[3];
+ /*
+ * This signed field specifies by how much to adjust the frequency
+ * of sync timer updates (measured in parts per billion).
+ */
+ int32_t ptp_freq_adj_ppb;
+ uint8_t unused_1[4];
+} __rte_packed;
+
+/* hwrm_port_mac_cfg_output (size:128b/16B) */
+struct hwrm_port_mac_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be received on the port.
+ * This value does not include the number of bytes used by
+ * Ethernet header and trailer (CRC).
+ */
+ uint16_t mru;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be transmitted on the port.
+ * This value does not include the number of bytes used by
+ * Ethernet header and trailer (CRC).
+ */
+ uint16_t mtu;
+ /* Current configuration of the IPG value. */
+ uint8_t ipg;
+ /* Current value of the loopback value. */
+ uint8_t lpbk;
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback such that
+ * host data is sent back to the host without modification.
+ */
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote loopback such that
+ * port logic will send packets back out the transmitter that
+ * are received.
+ */
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
+ #define HWRM_PORT_MAC_CFG_OUTPUT_LPBK_LAST \
+ HWRM_PORT_MAC_CFG_OUTPUT_LPBK_REMOTE
+ uint8_t unused_0;
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_port_mac_qcfg *
+ **********************/
+
+
+/* hwrm_port_mac_qcfg_input (size:192b/24B) */
+struct hwrm_port_mac_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is to be configured. */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_port_mac_qcfg_output (size:256b/32B) */
+struct hwrm_port_mac_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be received on the port.
+ * This value does not include the number of bytes used by the
+ * Ethernet header and trailer (CRC).
+ */
+ uint16_t mru;
+ /*
+ * This is the configured maximum length of Ethernet packet
+ * payload that is allowed to be transmitted on the port.
+ * This value does not include the number of bytes used by the
+ * Ethernet header and trailer (CRC).
+ */
+ uint16_t mtu;
+ /*
+ * The minimum IPG that will
+ * be sent between packets by this port.
+ */
+ uint8_t ipg;
+ /* The loopback setting for the MAC. */
+ uint8_t lpbk;
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback such that
+ * host data is sent back to the host without modification.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote loopback such that
+ * port logic will send packets back out the transmitter that
+ * are received.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_LAST \
+ HWRM_PORT_MAC_QCFG_OUTPUT_LPBK_REMOTE
+ /*
+ * Priority setting for VLAN PRI to CoS mapping.
+ * # Each XXX_pri variable shall have a unique priority value
+ * when it is being used.
+ * # When comparing priorities of mappings, higher value
+ * indicates higher priority.
+ * For example, a value of 0-3 is returned where 0 is being
+ * the lowest priority and 3 is being the highest priority.
+ * # If the correspoding CoS mapping is not enabled, then this
+ * field should be ignored.
+ * # This value indicates the normalized priority value retained
+ * in the HWRM.
+ */
+ uint8_t vlan_pri2cos_map_pri;
+ /*
+ * In this field, a number of CoS mappings related flags
+ * are used to indicate configured CoS mappings.
+ */
+ uint8_t flags;
+ /*
+ * When this bit is set to '1', the inner VLAN PRI to CoS mapping
+ * is enabled.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_VLAN_PRI2COS_ENABLE \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', tunnel VLAN PRI field to
+ * CoS mapping is enabled.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_TUNNEL_PRI2COS_ENABLE \
+ UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', the IP DSCP to CoS mapping is
+ * enabled.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_IP_DSCP2COS_ENABLE \
+ UINT32_C(0x4)
+ /*
+ * When this bit is '1', the Out-Of-Box WoL is enabled on this
+ * port.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_OOB_WOL_ENABLE \
+ UINT32_C(0x8)
+ /* When this bit is '1', PTP is enabled for RX on this port. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_PTP_RX_TS_CAPTURE_ENABLE \
+ UINT32_C(0x10)
+ /* When this bit is '1', PTP is enabled for TX on this port. */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_FLAGS_PTP_TX_TS_CAPTURE_ENABLE \
+ UINT32_C(0x20)
+ /*
+ * Priority setting for tunnel VLAN PRI to CoS mapping.
+ * # Each XXX_pri variable shall have a unique priority value
+ * when it is being used.
+ * # When comparing priorities of mappings, higher value
+ * indicates higher priority.
+ * For example, a value of 0-3 is returned where 0 is being
+ * the lowest priority and 3 is being the highest priority.
+ * # If the correspoding CoS mapping is not enabled, then this
+ * field should be ignored.
+ * # This value indicates the normalized priority value retained
+ * in the HWRM.
+ */
+ uint8_t tunnel_pri2cos_map_pri;
+ /*
+ * Priority setting for DSCP to PRI mapping.
+ * # Each XXX_pri variable shall have a unique priority value
+ * when it is being used.
+ * # When comparing priorities of mappings, higher value
+ * indicates higher priority.
+ * For example, a value of 0-3 is returned where 0 is being
+ * the lowest priority and 3 is being the highest priority.
+ * # If the correspoding CoS mapping is not enabled, then this
+ * field should be ignored.
+ * # This value indicates the normalized priority value retained
+ * in the HWRM.
+ */
+ uint8_t dscp2pri_map_pri;
+ /*
+ * This is a 16-bit bit mask that represents the
+ * current configuration of time stamp capture of PTP messages
+ * on the receive side of this port.
+ * If bit 'i' is set, then the receive side of the port
+ * is configured to capture the time stamp of every
+ * received PTP message with messageType field value set
+ * to i.
+ * If all bits are set to 0 (i.e. field value set 0),
+ * then the receive side of the port is not configured
+ * to capture timestamp for PTP messages.
+ * If all bits are set to 1, then the receive side of the
+ * port is configured to capture timestamp for all PTP
+ * messages.
+ */
+ uint16_t rx_ts_capture_ptp_msg_type;
+ /*
+ * This is a 16-bit bit mask that represents the
+ * current configuration of time stamp capture of PTP messages
+ * on the transmit side of this port.
+ * If bit 'i' is set, then the transmit side of the port
+ * is configured to capture the time stamp of every
+ * received PTP message with messageType field value set
+ * to i.
+ * If all bits are set to 0 (i.e. field value set 0),
+ * then the transmit side of the port is not configured
+ * to capture timestamp for PTP messages.
+ * If all bits are set to 1, then the transmit side of the
+ * port is configured to capture timestamp for all PTP
+ * messages.
+ */
+ uint16_t tx_ts_capture_ptp_msg_type;
+ /* Configuration of CoS fields. */
+ uint8_t cos_field_cfg;
+ /* Reserved */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_RSVD \
+ UINT32_C(0x1)
+ /*
+ * This field is used for selecting VLAN PRI value
+ * based on whether one or two VLAN Tags are present in
+ * the inner packet headers of tunneled packets or
+ * non-tunneled packets.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_MASK \
+ UINT32_C(0x6)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_SFT \
+ 1
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags are
+ * present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_INNERMOST \
+ (UINT32_C(0x0) << 1)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags are
+ * present in the inner packet headers.
+ * No VLAN PRI is selected for this configuration
+ * if only one VLAN Tag is present in the inner
+ * packet headers.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTER \
+ (UINT32_C(0x1) << 1)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the inner packet headers
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_OUTERMOST \
+ (UINT32_C(0x2) << 1)
+ /* Unspecified */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED \
+ (UINT32_C(0x3) << 1)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_LAST \
+ HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field is used for selecting tunnel VLAN PRI value
+ * based on whether one or two VLAN Tags are present in
+ * the tunnel headers of tunneled packets. This selection
+ * does not apply to non-tunneled packets.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_MASK \
+ UINT32_C(0x18)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_SFT \
+ 3
+ /*
+ * Select inner VLAN PRI when 1 or 2 VLAN Tags are
+ * present in the tunnel packet headers
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_INNERMOST \
+ (UINT32_C(0x0) << 3)
+ /*
+ * Select outer VLAN Tag PRI when 2 VLAN Tags are
+ * present in the tunnel packet headers.
+ * No VLAN PRI is selected for this configuration
+ * if only one VLAN Tag is present in the tunnel
+ * packet headers.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTER \
+ (UINT32_C(0x1) << 3)
+ /*
+ * Select outermost VLAN PRI when 1 or 2 VLAN Tags
+ * are present in the tunnel packet headers
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_OUTERMOST \
+ (UINT32_C(0x2) << 3)
+ /* Unspecified */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED \
+ (UINT32_C(0x3) << 3)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_LAST \
+ HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_T_VLAN_PRI_SEL_UNSPECIFIED
+ /*
+ * This field is used to provide default CoS value that
+ * has been configured on this port.
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_DEFAULT_COS_MASK \
+ UINT32_C(0xe0)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_COS_FIELD_CFG_DEFAULT_COS_SFT \
+ 5
+ uint8_t unused_1;
+ uint16_t port_svif_info;
+ /*
+ * This field specifies the source virtual interface of the port being
+ * queried. Drivers can use this to program port svif field in the
+ * L2 context table
+ */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_PORT_SVIF_INFO_PORT_SVIF_MASK \
+ UINT32_C(0x7fff)
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_PORT_SVIF_INFO_PORT_SVIF_SFT 0
+ /* This field specifies whether port_svif is valid or not */
+ #define HWRM_PORT_MAC_QCFG_OUTPUT_PORT_SVIF_INFO_PORT_SVIF_VALID \
+ UINT32_C(0x8000)
+ uint8_t unused_2[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_port_mac_ptp_qcfg *
+ **************************/
+
+
+/* hwrm_port_mac_ptp_qcfg_input (size:192b/24B) */
+struct hwrm_port_mac_ptp_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is being queried. */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_port_mac_ptp_qcfg_output (size:640b/80B) */
+struct hwrm_port_mac_ptp_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * In this field, a number of PTP related flags
+ * are used to indicate configured PTP capabilities.
+ */
+ uint8_t flags;
+ /*
+ * When this bit is set to '1', the PTP related registers are
+ * directly accessible by the host.
+ */
+ #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_DIRECT_ACCESS \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', the device supports one-step
+ * Tx timestamping.
+ */
+ #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_ONE_STEP_TX_TS \
+ UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', the PTP information is accessible
+ * via HWRM commands.
+ */
+ #define HWRM_PORT_MAC_PTP_QCFG_OUTPUT_FLAGS_HWRM_ACCESS \
+ UINT32_C(0x8)
+ uint8_t unused_0[3];
+ /* Offset of the PTP register for the lower 32 bits of timestamp for RX. */
+ uint32_t rx_ts_reg_off_lower;
+ /* Offset of the PTP register for the upper 32 bits of timestamp for RX. */
+ uint32_t rx_ts_reg_off_upper;
+ /* Offset of the PTP register for the sequence ID for RX. */
+ uint32_t rx_ts_reg_off_seq_id;
+ /* Offset of the first PTP source ID for RX. */
+ uint32_t rx_ts_reg_off_src_id_0;
+ /* Offset of the second PTP source ID for RX. */
+ uint32_t rx_ts_reg_off_src_id_1;
+ /* Offset of the third PTP source ID for RX. */
+ uint32_t rx_ts_reg_off_src_id_2;
+ /* Offset of the domain ID for RX. */
+ uint32_t rx_ts_reg_off_domain_id;
+ /* Offset of the PTP FIFO register for RX. */
+ uint32_t rx_ts_reg_off_fifo;
+ /* Offset of the PTP advance FIFO register for RX. */
+ uint32_t rx_ts_reg_off_fifo_adv;
+ /* PTP timestamp granularity for RX. */
+ uint32_t rx_ts_reg_off_granularity;
+ /* Offset of the PTP register for the lower 32 bits of timestamp for TX. */
+ uint32_t tx_ts_reg_off_lower;
+ /* Offset of the PTP register for the upper 32 bits of timestamp for TX. */
+ uint32_t tx_ts_reg_off_upper;
+ /* Offset of the PTP register for the sequence ID for TX. */
+ uint32_t tx_ts_reg_off_seq_id;
+ /* Offset of the PTP FIFO register for TX. */
+ uint32_t tx_ts_reg_off_fifo;
+ /* PTP timestamp granularity for TX. */
+ uint32_t tx_ts_reg_off_granularity;
+ uint8_t unused_1[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* Port Tx Statistics Format */
+/* tx_port_stats (size:3264b/408B) */
+struct tx_port_stats {
+ /* Total Number of 64 Bytes frames transmitted */
+ uint64_t tx_64b_frames;
+ /* Total Number of 65-127 Bytes frames transmitted */
+ uint64_t tx_65b_127b_frames;
+ /* Total Number of 128-255 Bytes frames transmitted */
+ uint64_t tx_128b_255b_frames;
+ /* Total Number of 256-511 Bytes frames transmitted */
+ uint64_t tx_256b_511b_frames;
+ /* Total Number of 512-1023 Bytes frames transmitted */
+ uint64_t tx_512b_1023b_frames;
+ /* Total Number of 1024-1518 Bytes frames transmitted */
+ uint64_t tx_1024b_1518b_frames;
+ /*
+ * Total Number of each good VLAN (exludes FCS errors)
+ * frame transmitted which is 1519 to 1522 bytes in length
+ * inclusive (excluding framing bits but including FCS bytes).
+ */
+ uint64_t tx_good_vlan_frames;
+ /* Total Number of 1519-2047 Bytes frames transmitted */
+ uint64_t tx_1519b_2047b_frames;
+ /* Total Number of 2048-4095 Bytes frames transmitted */
+ uint64_t tx_2048b_4095b_frames;
+ /* Total Number of 4096-9216 Bytes frames transmitted */
+ uint64_t tx_4096b_9216b_frames;
+ /* Total Number of 9217-16383 Bytes frames transmitted */
+ uint64_t tx_9217b_16383b_frames;
+ /* Total Number of good frames transmitted */
+ uint64_t tx_good_frames;
+ /* Total Number of frames transmitted */
+ uint64_t tx_total_frames;
+ /* Total number of unicast frames transmitted */
+ uint64_t tx_ucast_frames;
+ /* Total number of multicast frames transmitted */
+ uint64_t tx_mcast_frames;
+ /* Total number of broadcast frames transmitted */
+ uint64_t tx_bcast_frames;
+ /* Total number of PAUSE control frames transmitted */
+ uint64_t tx_pause_frames;
+ /*
+ * Total number of PFC/per-priority PAUSE
+ * control frames transmitted
+ */
+ uint64_t tx_pfc_frames;
+ /* Total number of jabber frames transmitted */
+ uint64_t tx_jabber_frames;
+ /* Total number of frames transmitted with FCS error */
+ uint64_t tx_fcs_err_frames;
+ /* Total number of control frames transmitted */
+ uint64_t tx_control_frames;
+ /* Total number of over-sized frames transmitted */
+ uint64_t tx_oversz_frames;
+ /* Total number of frames with single deferral */
+ uint64_t tx_single_dfrl_frames;
+ /* Total number of frames with multiple deferrals */
+ uint64_t tx_multi_dfrl_frames;
+ /* Total number of frames with single collision */
+ uint64_t tx_single_coll_frames;
+ /* Total number of frames with multiple collisions */
+ uint64_t tx_multi_coll_frames;
+ /* Total number of frames with late collisions */
+ uint64_t tx_late_coll_frames;
+ /* Total number of frames with excessive collisions */
+ uint64_t tx_excessive_coll_frames;
+ /* Total number of fragmented frames transmitted */
+ uint64_t tx_frag_frames;
+ /* Total number of transmit errors */
+ uint64_t tx_err;
+ /* Total number of single VLAN tagged frames transmitted */
+ uint64_t tx_tagged_frames;
+ /* Total number of double VLAN tagged frames transmitted */
+ uint64_t tx_dbl_tagged_frames;
+ /* Total number of runt frames transmitted */
+ uint64_t tx_runt_frames;
+ /* Total number of TX FIFO under runs */
+ uint64_t tx_fifo_underruns;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 0 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri0;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 1 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri1;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 2 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri2;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 3 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri3;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 4 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri4;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 5 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri5;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 6 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri6;
+ /*
+ * Total number of PFC frames with PFC enabled bit for
+ * Pri 7 transmitted
+ */
+ uint64_t tx_pfc_ena_frames_pri7;
+ /* Total number of EEE LPI Events on TX */
+ uint64_t tx_eee_lpi_events;
+ /* EEE LPI Duration Counter on TX */
+ uint64_t tx_eee_lpi_duration;
+ /*
+ * Total number of Link Level Flow Control (LLFC) messages
+ * transmitted
+ */
+ uint64_t tx_llfc_logical_msgs;
+ /* Total number of HCFC messages transmitted */
+ uint64_t tx_hcfc_msgs;
+ /* Total number of TX collisions */
+ uint64_t tx_total_collisions;
+ /* Total number of transmitted bytes */
+ uint64_t tx_bytes;
+ /* Total number of end-to-end HOL frames */
+ uint64_t tx_xthol_frames;
+ /* Total Tx Drops per Port reported by STATS block */
+ uint64_t tx_stat_discard;
+ /* Total Tx Error Drops per Port reported by STATS block */
+ uint64_t tx_stat_error;
+} __rte_packed;
+
+/* Port Rx Statistics Format */
+/* rx_port_stats (size:4224b/528B) */
+struct rx_port_stats {
+ /* Total Number of 64 Bytes frames received */
+ uint64_t rx_64b_frames;
+ /* Total Number of 65-127 Bytes frames received */
+ uint64_t rx_65b_127b_frames;
+ /* Total Number of 128-255 Bytes frames received */
+ uint64_t rx_128b_255b_frames;
+ /* Total Number of 256-511 Bytes frames received */
+ uint64_t rx_256b_511b_frames;
+ /* Total Number of 512-1023 Bytes frames received */
+ uint64_t rx_512b_1023b_frames;
+ /* Total Number of 1024-1518 Bytes frames received */
+ uint64_t rx_1024b_1518b_frames;
+ /*
+ * Total Number of each good VLAN (exludes FCS errors)
+ * frame received which is 1519 to 1522 bytes in length
+ * inclusive (excluding framing bits but including FCS bytes).
+ */
+ uint64_t rx_good_vlan_frames;
+ /* Total Number of 1519-2047 Bytes frames received */
+ uint64_t rx_1519b_2047b_frames;
+ /* Total Number of 2048-4095 Bytes frames received */
+ uint64_t rx_2048b_4095b_frames;
+ /* Total Number of 4096-9216 Bytes frames received */
+ uint64_t rx_4096b_9216b_frames;
+ /* Total Number of 9217-16383 Bytes frames received */
+ uint64_t rx_9217b_16383b_frames;
+ /* Total number of frames received */
+ uint64_t rx_total_frames;
+ /* Total number of unicast frames received */
+ uint64_t rx_ucast_frames;
+ /* Total number of multicast frames received */
+ uint64_t rx_mcast_frames;
+ /* Total number of broadcast frames received */
+ uint64_t rx_bcast_frames;
+ /* Total number of received frames with FCS error */
+ uint64_t rx_fcs_err_frames;
+ /* Total number of control frames received */
+ uint64_t rx_ctrl_frames;
+ /* Total number of PAUSE frames received */
+ uint64_t rx_pause_frames;
+ /* Total number of PFC frames received */
+ uint64_t rx_pfc_frames;
+ /*
+ * Total number of frames received with an unsupported
+ * opcode
+ */
+ uint64_t rx_unsupported_opcode_frames;
+ /*
+ * Total number of frames received with an unsupported
+ * DA for pause and PFC
+ */
+ uint64_t rx_unsupported_da_pausepfc_frames;
+ /* Total number of frames received with an unsupported SA */
+ uint64_t rx_wrong_sa_frames;
+ /* Total number of received packets with alignment error */
+ uint64_t rx_align_err_frames;
+ /* Total number of received frames with out-of-range length */
+ uint64_t rx_oor_len_frames;
+ /* Total number of received frames with error termination */
+ uint64_t rx_code_err_frames;
+ /*
+ * Total number of received frames with a false carrier is
+ * detected during idle, as defined by RX_ER samples active
+ * and RXD is 0xE. The event is reported along with the
+ * statistics generated on the next received frame. Only
+ * one false carrier condition can be detected and logged
+ * between frames.
+ *
+ * Carrier event, valid for 10M/100M speed modes only.
+ */
+ uint64_t rx_false_carrier_frames;
+ /* Total number of over-sized frames received */
+ uint64_t rx_ovrsz_frames;
+ /* Total number of jabber packets received */
+ uint64_t rx_jbr_frames;
+ /* Total number of received frames with MTU error */
+ uint64_t rx_mtu_err_frames;
+ /* Total number of received frames with CRC match */
+ uint64_t rx_match_crc_frames;
+ /* Total number of frames received promiscuously */
+ uint64_t rx_promiscuous_frames;
+ /*
+ * Total number of received frames with one or two VLAN
+ * tags
+ */
+ uint64_t rx_tagged_frames;
+ /* Total number of received frames with two VLAN tags */
+ uint64_t rx_double_tagged_frames;
+ /* Total number of truncated frames received */
+ uint64_t rx_trunc_frames;
+ /* Total number of good frames (without errors) received */
+ uint64_t rx_good_frames;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 0
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri0;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 1
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri1;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 2
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri2;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 3
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri3;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 4
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri4;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 5
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri5;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 6
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri6;
+ /*
+ * Total number of received PFC frames with transition from
+ * XON to XOFF on Pri 7
+ */
+ uint64_t rx_pfc_xon2xoff_frames_pri7;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 0
+ */
+ uint64_t rx_pfc_ena_frames_pri0;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 1
+ */
+ uint64_t rx_pfc_ena_frames_pri1;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 2
+ */
+ uint64_t rx_pfc_ena_frames_pri2;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 3
+ */
+ uint64_t rx_pfc_ena_frames_pri3;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 4
+ */
+ uint64_t rx_pfc_ena_frames_pri4;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 5
+ */
+ uint64_t rx_pfc_ena_frames_pri5;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 6
+ */
+ uint64_t rx_pfc_ena_frames_pri6;
+ /*
+ * Total number of received PFC frames with PFC enabled
+ * bit for Pri 7
+ */
+ uint64_t rx_pfc_ena_frames_pri7;
+ /* Total Number of frames received with SCH CRC error */
+ uint64_t rx_sch_crc_err_frames;
+ /* Total Number of under-sized frames received */
+ uint64_t rx_undrsz_frames;
+ /* Total Number of fragmented frames received */
+ uint64_t rx_frag_frames;
+ /* Total number of RX EEE LPI Events */
+ uint64_t rx_eee_lpi_events;
+ /* EEE LPI Duration Counter on RX */
+ uint64_t rx_eee_lpi_duration;
+ /*
+ * Total number of physical type Link Level Flow Control
+ * (LLFC) messages received
+ */
+ uint64_t rx_llfc_physical_msgs;
+ /*
+ * Total number of logical type Link Level Flow Control
+ * (LLFC) messages received
+ */
+ uint64_t rx_llfc_logical_msgs;
+ /*
+ * Total number of logical type Link Level Flow Control
+ * (LLFC) messages received with CRC error
+ */
+ uint64_t rx_llfc_msgs_with_crc_err;
+ /* Total number of HCFC messages received */
+ uint64_t rx_hcfc_msgs;
+ /* Total number of HCFC messages received with CRC error */
+ uint64_t rx_hcfc_msgs_with_crc_err;
+ /* Total number of received bytes */
+ uint64_t rx_bytes;
+ /* Total number of bytes received in runt frames */
+ uint64_t rx_runt_bytes;
+ /* Total number of runt frames received */
+ uint64_t rx_runt_frames;
+ /* Total Rx Discards per Port reported by STATS block */
+ uint64_t rx_stat_discard;
+ uint64_t rx_stat_err;
+} __rte_packed;
+
+/********************
+ * hwrm_port_qstats *
+ ********************/
+
+
+/* hwrm_port_qstats_input (size:320b/40B) */
+struct hwrm_port_qstats_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is being queried. */
+ uint16_t port_id;
+ uint8_t flags;
+ /* This value is not used to avoid backward compatibility issues. */
+ #define HWRM_PORT_QSTATS_INPUT_FLAGS_UNUSED UINT32_C(0x0)
+ /*
+ * This bit is set to 1 when request is for a counter mask,
+ * representing the width of each of the stats counters, rather
+ * than counters themselves.
+ */
+ #define HWRM_PORT_QSTATS_INPUT_FLAGS_COUNTER_MASK UINT32_C(0x1)
+ #define HWRM_PORT_QSTATS_INPUT_FLAGS_LAST \
+ HWRM_PORT_QSTATS_INPUT_FLAGS_COUNTER_MASK
+ uint8_t unused_0[5];
+ /*
+ * This is the host address where
+ * Tx port statistics will be stored
+ */
+ uint64_t tx_stat_host_addr;
+ /*
+ * This is the host address where
+ * Rx port statistics will be stored
+ */
+ uint64_t rx_stat_host_addr;
+} __rte_packed;
+
+/* hwrm_port_qstats_output (size:128b/16B) */
+struct hwrm_port_qstats_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The size of TX port statistics block in bytes. */
+ uint16_t tx_stat_size;
+ /* The size of RX port statistics block in bytes. */
+ uint16_t rx_stat_size;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* Port Tx Statistics extended Format */
+/* tx_port_stats_ext (size:2048b/256B) */
+struct tx_port_stats_ext {
+ /* Total number of tx bytes count on cos queue 0 */
+ uint64_t tx_bytes_cos0;
+ /* Total number of tx bytes count on cos queue 1 */
+ uint64_t tx_bytes_cos1;
+ /* Total number of tx bytes count on cos queue 2 */
+ uint64_t tx_bytes_cos2;
+ /* Total number of tx bytes count on cos queue 3 */
+ uint64_t tx_bytes_cos3;
+ /* Total number of tx bytes count on cos queue 4 */
+ uint64_t tx_bytes_cos4;
+ /* Total number of tx bytes count on cos queue 5 */
+ uint64_t tx_bytes_cos5;
+ /* Total number of tx bytes count on cos queue 6 */
+ uint64_t tx_bytes_cos6;
+ /* Total number of tx bytes count on cos queue 7 */
+ uint64_t tx_bytes_cos7;
+ /* Total number of tx packets count on cos queue 0 */
+ uint64_t tx_packets_cos0;
+ /* Total number of tx packets count on cos queue 1 */
+ uint64_t tx_packets_cos1;
+ /* Total number of tx packets count on cos queue 2 */
+ uint64_t tx_packets_cos2;
+ /* Total number of tx packets count on cos queue 3 */
+ uint64_t tx_packets_cos3;
+ /* Total number of tx packets count on cos queue 4 */
+ uint64_t tx_packets_cos4;
+ /* Total number of tx packets count on cos queue 5 */
+ uint64_t tx_packets_cos5;
+ /* Total number of tx packets count on cos queue 6 */
+ uint64_t tx_packets_cos6;
+ /* Total number of tx packets count on cos queue 7 */
+ uint64_t tx_packets_cos7;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 0 */
+ uint64_t pfc_pri0_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 0 */
+ uint64_t pfc_pri0_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 1 */
+ uint64_t pfc_pri1_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 1 */
+ uint64_t pfc_pri1_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 2 */
+ uint64_t pfc_pri2_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 2 */
+ uint64_t pfc_pri2_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 3 */
+ uint64_t pfc_pri3_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 3 */
+ uint64_t pfc_pri3_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 4 */
+ uint64_t pfc_pri4_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 4 */
+ uint64_t pfc_pri4_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 5 */
+ uint64_t pfc_pri5_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 5 */
+ uint64_t pfc_pri5_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 6 */
+ uint64_t pfc_pri6_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 6 */
+ uint64_t pfc_pri6_tx_transitions;
+ /* time duration between transmitting a XON -> XOFF and a subsequent XOFF -> XON for priority 7 */
+ uint64_t pfc_pri7_tx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 7 */
+ uint64_t pfc_pri7_tx_transitions;
+} __rte_packed;
+
+/* Port Rx Statistics extended Format */
+/* rx_port_stats_ext (size:3648b/456B) */
+struct rx_port_stats_ext {
+ /* Number of times link state changed to down */
+ uint64_t link_down_events;
+ /* Number of times the idle rings with pause bit are found */
+ uint64_t continuous_pause_events;
+ /* Number of times the active rings pause bit resumed back */
+ uint64_t resume_pause_events;
+ /* Number of times, the ROCE cos queue PFC is disabled to avoid pause flood/burst */
+ uint64_t continuous_roce_pause_events;
+ /* Number of times, the ROCE cos queue PFC is enabled back */
+ uint64_t resume_roce_pause_events;
+ /* Total number of rx bytes count on cos queue 0 */
+ uint64_t rx_bytes_cos0;
+ /* Total number of rx bytes count on cos queue 1 */
+ uint64_t rx_bytes_cos1;
+ /* Total number of rx bytes count on cos queue 2 */
+ uint64_t rx_bytes_cos2;
+ /* Total number of rx bytes count on cos queue 3 */
+ uint64_t rx_bytes_cos3;
+ /* Total number of rx bytes count on cos queue 4 */
+ uint64_t rx_bytes_cos4;
+ /* Total number of rx bytes count on cos queue 5 */
+ uint64_t rx_bytes_cos5;
+ /* Total number of rx bytes count on cos queue 6 */
+ uint64_t rx_bytes_cos6;
+ /* Total number of rx bytes count on cos queue 7 */
+ uint64_t rx_bytes_cos7;
+ /* Total number of rx packets count on cos queue 0 */
+ uint64_t rx_packets_cos0;
+ /* Total number of rx packets count on cos queue 1 */
+ uint64_t rx_packets_cos1;
+ /* Total number of rx packets count on cos queue 2 */
+ uint64_t rx_packets_cos2;
+ /* Total number of rx packets count on cos queue 3 */
+ uint64_t rx_packets_cos3;
+ /* Total number of rx packets count on cos queue 4 */
+ uint64_t rx_packets_cos4;
+ /* Total number of rx packets count on cos queue 5 */
+ uint64_t rx_packets_cos5;
+ /* Total number of rx packets count on cos queue 6 */
+ uint64_t rx_packets_cos6;
+ /* Total number of rx packets count on cos queue 7 */
+ uint64_t rx_packets_cos7;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 0 */
+ uint64_t pfc_pri0_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 0 */
+ uint64_t pfc_pri0_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 1 */
+ uint64_t pfc_pri1_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 1 */
+ uint64_t pfc_pri1_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 2 */
+ uint64_t pfc_pri2_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 2 */
+ uint64_t pfc_pri2_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 3 */
+ uint64_t pfc_pri3_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 3 */
+ uint64_t pfc_pri3_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 4 */
+ uint64_t pfc_pri4_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 4 */
+ uint64_t pfc_pri4_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 5 */
+ uint64_t pfc_pri5_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 5 */
+ uint64_t pfc_pri5_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 6 */
+ uint64_t pfc_pri6_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 6 */
+ uint64_t pfc_pri6_rx_transitions;
+ /* time duration receiving a XON -> XOFF and a subsequent XOFF -> XON for priority 7 */
+ uint64_t pfc_pri7_rx_duration_us;
+ /* Number of times, a XON -> XOFF and XOFF -> XON transitions occur for priority 7 */
+ uint64_t pfc_pri7_rx_transitions;
+ /* Total number of received bits */
+ uint64_t rx_bits;
+ /* The number of events where the port receive buffer was over 85% full */
+ uint64_t rx_buffer_passed_threshold;
+ /*
+ * The number of symbol errors that wasn't corrected by FEC correction
+ * alogirithm
+ */
+ uint64_t rx_pcs_symbol_err;
+ /* The number of corrected bits on the port according to active FEC */
+ uint64_t rx_corrected_bits;
+ /* Total number of rx discard bytes count on cos queue 0 */
+ uint64_t rx_discard_bytes_cos0;
+ /* Total number of rx discard bytes count on cos queue 1 */
+ uint64_t rx_discard_bytes_cos1;
+ /* Total number of rx discard bytes count on cos queue 2 */
+ uint64_t rx_discard_bytes_cos2;
+ /* Total number of rx discard bytes count on cos queue 3 */
+ uint64_t rx_discard_bytes_cos3;
+ /* Total number of rx discard bytes count on cos queue 4 */
+ uint64_t rx_discard_bytes_cos4;
+ /* Total number of rx discard bytes count on cos queue 5 */
+ uint64_t rx_discard_bytes_cos5;
+ /* Total number of rx discard bytes count on cos queue 6 */
+ uint64_t rx_discard_bytes_cos6;
+ /* Total number of rx discard bytes count on cos queue 7 */
+ uint64_t rx_discard_bytes_cos7;
+ /* Total number of rx discard packets count on cos queue 0 */
+ uint64_t rx_discard_packets_cos0;
+ /* Total number of rx discard packets count on cos queue 1 */
+ uint64_t rx_discard_packets_cos1;
+ /* Total number of rx discard packets count on cos queue 2 */
+ uint64_t rx_discard_packets_cos2;
+ /* Total number of rx discard packets count on cos queue 3 */
+ uint64_t rx_discard_packets_cos3;
+ /* Total number of rx discard packets count on cos queue 4 */
+ uint64_t rx_discard_packets_cos4;
+ /* Total number of rx discard packets count on cos queue 5 */
+ uint64_t rx_discard_packets_cos5;
+ /* Total number of rx discard packets count on cos queue 6 */
+ uint64_t rx_discard_packets_cos6;
+ /* Total number of rx discard packets count on cos queue 7 */
+ uint64_t rx_discard_packets_cos7;
+} __rte_packed;
+
+/*
+ * Port Rx Statistics extended PFC WatchDog Format.
+ * StormDetect and StormRevert event determination is based
+ * on an integration period and a percentage threshold.
+ * StormDetect event - when percentage of XOFF frames received
+ * within an integration period exceeds the configured threshold.
+ * StormRevert event - when percentage of XON frames received
+ * within an integration period exceeds the configured threshold.
+ * Actual number of XOFF/XON frames for the events to be triggered
+ * depends on both configured integration period and sampling rate.
+ * The statistics in this structure represent counts of specified
+ * events from the moment the feature (PFC WatchDog) is enabled via
+ * hwrm_queue_pfc_enable_cfg call.
+ */
+/* rx_port_stats_ext_pfc_wd (size:5120b/640B) */
+struct rx_port_stats_ext_pfc_wd {
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 0
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri0;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 1
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri1;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 2
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri2;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 3
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri3;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 4
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri4;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 5
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri5;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 6
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri6;
+ /*
+ * Total number of PFC WatchDog StormDetect events detected
+ * for Pri 7
+ */
+ uint64_t rx_pfc_watchdog_storms_detected_pri7;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 0
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri0;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 1
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri1;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 2
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri2;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 3
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri3;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 4
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri4;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 5
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri5;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 6
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri6;
+ /*
+ * Total number of PFC WatchDog StormRevert events detected
+ * for Pri 7
+ */
+ uint64_t rx_pfc_watchdog_storms_reverted_pri7;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri0;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri1;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri2;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri3;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri4;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri5;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri6;
+ /*
+ * Total number of packets received during PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_pri7;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri0;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri1;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri2;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri3;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri4;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri5;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri6;
+ /*
+ * Total number of bytes received during PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_pri7;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri0;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri1;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri2;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri3;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri4;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri5;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri6;
+ /*
+ * Total number of packets dropped on rx during PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_packets_dropped_pri7;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri0;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri1;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri2;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri3;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri4;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri5;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri6;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_storms_rx_bytes_dropped_pri7;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri0;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri1;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri2;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri3;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri4;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri5;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri6;
+ /*
+ * Number of packets received during last PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_pri7;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri0;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri1;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri2;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri3;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri4;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri5;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri6;
+ /*
+ * Number of bytes received during last PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_pri7;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri0;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri1;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri2;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri3;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri4;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri5;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri6;
+ /*
+ * Number of packets dropped on rx during last PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_packets_dropped_pri7;
+ /*
+ * Total number of bytes dropped on rx during PFC watchdog storm
+ * for pri 0
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri0;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 1
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri1;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 2
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri2;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 3
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri3;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 4
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri4;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 5
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri5;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 6
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri6;
+ /*
+ * Number of bytes dropped on rx during last PFC watchdog storm
+ * for pri 7
+ */
+ uint64_t rx_pfc_watchdog_last_storm_rx_bytes_dropped_pri7;
+} __rte_packed;
+
+/************************
+ * hwrm_port_qstats_ext *
+ ************************/
+
+
+/* hwrm_port_qstats_ext_input (size:320b/40B) */
+struct hwrm_port_qstats_ext_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is being queried. */
+ uint16_t port_id;
+ /*
+ * The size of TX port extended
+ * statistics block in bytes.
+ */
+ uint16_t tx_stat_size;
+ /*
+ * The size of RX port extended
+ * statistics block in bytes
+ */
+ uint16_t rx_stat_size;
+ uint8_t flags;
+ /* This value is not used to avoid backward compatibility issues. */
+ #define HWRM_PORT_QSTATS_EXT_INPUT_FLAGS_UNUSED UINT32_C(0x0)
+ /*
+ * This bit is set to 1 when request is for the counter mask,
+ * representing width of each of the stats counters, rather than
+ * counters themselves.
+ */
+ #define HWRM_PORT_QSTATS_EXT_INPUT_FLAGS_COUNTER_MASK UINT32_C(0x1)
+ #define HWRM_PORT_QSTATS_EXT_INPUT_FLAGS_LAST \
+ HWRM_PORT_QSTATS_EXT_INPUT_FLAGS_COUNTER_MASK
+ uint8_t unused_0;
+ /*
+ * This is the host address where
+ * Tx port statistics will be stored
+ */
+ uint64_t tx_stat_host_addr;
+ /*
+ * This is the host address where
+ * Rx port statistics will be stored
+ */
+ uint64_t rx_stat_host_addr;
+} __rte_packed;
+
+/* hwrm_port_qstats_ext_output (size:128b/16B) */
+struct hwrm_port_qstats_ext_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The size of TX port statistics block in bytes. */
+ uint16_t tx_stat_size;
+ /* The size of RX port statistics block in bytes. */
+ uint16_t rx_stat_size;
+ /* Total number of active cos queues available. */
+ uint16_t total_active_cos_queues;
+ uint8_t flags;
+ /*
+ * If set to 1, then this field indicates that clear
+ * roce specific counters is supported.
+ */
+ #define HWRM_PORT_QSTATS_EXT_OUTPUT_FLAGS_CLEAR_ROCE_COUNTERS_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*******************************
+ * hwrm_port_qstats_ext_pfc_wd *
+ *******************************/
+
+
+/* hwrm_port_qstats_ext_pfc_wd_input (size:256b/32B) */
+struct hwrm_port_qstats_ext_pfc_wd_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is being queried. */
+ uint16_t port_id;
+ /*
+ * The size of rx_port_stats_ext_pfc_wd
+ * block in bytes
+ */
+ uint16_t pfc_wd_stat_size;
+ uint8_t unused_0[4];
+ /*
+ * This is the host address where
+ * rx_port_stats_ext_pfc_wd will be stored
+ */
+ uint64_t pfc_wd_stat_host_addr;
+} __rte_packed;
+
+/* hwrm_port_qstats_ext_pfc_wd_output (size:128b/16B) */
+struct hwrm_port_qstats_ext_pfc_wd_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * The size of rx_port_stats_ext_pfc_wd
+ * statistics block in bytes.
+ */
+ uint16_t pfc_wd_stat_size;
+ uint8_t flags;
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+ uint8_t unused_0[4];
+} __rte_packed;
+
+/*************************
+ * hwrm_port_lpbk_qstats *
+ *************************/
+
+
+/* hwrm_port_lpbk_qstats_input (size:128b/16B) */
+struct hwrm_port_lpbk_qstats_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __rte_packed;
+
+/* hwrm_port_lpbk_qstats_output (size:768b/96B) */
+struct hwrm_port_lpbk_qstats_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Number of transmitted unicast frames */
+ uint64_t lpbk_ucast_frames;
+ /* Number of transmitted multicast frames */
+ uint64_t lpbk_mcast_frames;
+ /* Number of transmitted broadcast frames */
+ uint64_t lpbk_bcast_frames;
+ /* Number of transmitted bytes for unicast traffic */
+ uint64_t lpbk_ucast_bytes;
+ /* Number of transmitted bytes for multicast traffic */
+ uint64_t lpbk_mcast_bytes;
+ /* Number of transmitted bytes for broadcast traffic */
+ uint64_t lpbk_bcast_bytes;
+ /* Total Tx Drops for loopback traffic reported by STATS block */
+ uint64_t tx_stat_discard;
+ /* Total Tx Error Drops for loopback traffic reported by STATS block */
+ uint64_t tx_stat_error;
+ /* Total Rx Drops for loopback traffic reported by STATS block */
+ uint64_t rx_stat_discard;
+ /* Total Rx Error Drops for loopback traffic reported by STATS block */
+ uint64_t rx_stat_error;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/************************
+ * hwrm_port_ecn_qstats *
+ ************************/
+
+
+/* hwrm_port_ecn_qstats_input (size:256b/32B) */
+struct hwrm_port_ecn_qstats_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port that is being queried. Unused if NIC is in
+ * multi-host mode.
+ */
+ uint16_t port_id;
+ /*
+ * Size of the DMA buffer the caller has allocated for the firmware to
+ * write into.
+ */
+ uint16_t ecn_stat_buf_size;
+ uint8_t flags;
+ /* This value is not used to avoid backward compatibility issues. */
+ #define HWRM_PORT_ECN_QSTATS_INPUT_FLAGS_UNUSED UINT32_C(0x0)
+ /*
+ * This bit is set to 1 when request is for a counter mask,
+ * representing the width of each of the stats counters, rather
+ * than counters themselves.
+ */
+ #define HWRM_PORT_ECN_QSTATS_INPUT_FLAGS_COUNTER_MASK UINT32_C(0x1)
+ #define HWRM_PORT_ECN_QSTATS_INPUT_FLAGS_LAST \
+ HWRM_PORT_ECN_QSTATS_INPUT_FLAGS_COUNTER_MASK
+ uint8_t unused_0[3];
+ /*
+ * This is the host address where
+ * ECN port statistics will be stored
+ */
+ uint64_t ecn_stat_host_addr;
+} __rte_packed;
+
+/* hwrm_port_ecn_qstats_output (size:128b/16B) */
+struct hwrm_port_ecn_qstats_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* Number of bytes of stats the firmware wrote to the DMA buffer. */
+ uint16_t ecn_stat_buf_size;
+ /*
+ * Bitmask that indicates which CoS queues have ECN marking enabled.
+ * Bit i corresponds to CoS queue i.
+ */
+ uint8_t mark_en;
+ uint8_t unused_0[4];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/* ECN mark statistics format */
+/* port_stats_ecn (size:512b/64B) */
+struct port_stats_ecn {
+ /*
+ * Number of packets marked in CoS queue 0.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos0;
+ /*
+ * Number of packets marked in CoS queue 1.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos1;
+ /*
+ * Number of packets marked in CoS queue 2.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos2;
+ /*
+ * Number of packets marked in CoS queue 3.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos3;
+ /*
+ * Number of packets marked in CoS queue 4.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos4;
+ /*
+ * Number of packets marked in CoS queue 5.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos5;
+ /*
+ * Number of packets marked in CoS queue 6.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos6;
+ /*
+ * Number of packets marked in CoS queue 7.
+ * Or, if the driver requested counter masks, a mask to indicate the size
+ * of the counter.
+ */
+ uint64_t mark_cnt_cos7;
+} __rte_packed;
+
+/***********************
+ * hwrm_port_clr_stats *
+ ***********************/
+
+
+/* hwrm_port_clr_stats_input (size:192b/24B) */
+struct hwrm_port_clr_stats_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is being queried. */
+ uint16_t port_id;
+ uint8_t flags;
+ /*
+ * If set to 1, then this field indicates clear the following RoCE
+ * specific counters.
+ * RoCE associated TX/RX cos counters
+ * CNP associated TX/RX cos counters
+ * RoCE/CNP specific TX/RX flow counters
+ * Firmware will determine the RoCE/CNP cos queue based on qos profile.
+ * This flag is honored only when RoCE is enabled on that port.
+ */
+ #define HWRM_PORT_CLR_STATS_INPUT_FLAGS_ROCE_COUNTERS UINT32_C(0x1)
+ uint8_t unused_0[5];
+} __rte_packed;
+
+/* hwrm_port_clr_stats_output (size:128b/16B) */
+struct hwrm_port_clr_stats_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_port_phy_qcaps *
+ ***********************/
+
+
+/* hwrm_port_phy_qcaps_input (size:192b/24B) */
+struct hwrm_port_phy_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port that is being queried. */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_port_phy_qcaps_output (size:256b/32B) */
+struct hwrm_port_phy_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* PHY capability flags */
+ uint8_t flags;
+ /*
+ * If set to 1, then this field indicates that the
+ * link is capable of supporting EEE.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_EEE_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * If set to 1, then this field indicates that the
+ * PHY is capable of supporting external loopback.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_EXTERNAL_LPBK_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, then this field indicates that the
+ * PHY is capable of supporting loopback in autoneg mode.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_AUTONEG_LPBK_SUPPORTED \
+ UINT32_C(0x4)
+ /*
+ * Indicates if the configuration of shared PHY settings is supported.
+ * In cases where a physical port is shared by multiple functions
+ * (e.g. NPAR, multihost, etc), the configuration of PHY
+ * settings may not be allowed. Callers to HWRM_PORT_PHY_CFG will
+ * get an HWRM_ERR_CODE_RESOURCE_ACCESS_DENIED error in this case.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_SHARED_PHY_CFG_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1, it indicates that the port counters and extended
+ * port counters will not reset when the firmware shuts down or
+ * resets the PHY. These counters will only be reset during power
+ * cycle or by calling HWRM_PORT_CLR_STATS.
+ * If set to 0, the state of the counters is unspecified when
+ * firmware shuts down or resets the PHY.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_CUMULATIVE_COUNTERS_ON_RESET \
+ UINT32_C(0x10)
+ /*
+ * If set to 1, then this field indicates that the
+ * local loopback is not supported on this controller.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_LOCAL_LPBK_NOT_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * Reserved field. The HWRM shall set this field to 0.
+ * An HWRM client shall ignore this field.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_RSVD1_MASK \
+ UINT32_C(0xc0)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_FLAGS_RSVD1_SFT \
+ 6
+ /* Number of front panel ports for this device. */
+ uint8_t port_cnt;
+ /* Not supported or unknown */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_UNKNOWN UINT32_C(0x0)
+ /* single port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_1 UINT32_C(0x1)
+ /* 2-port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_2 UINT32_C(0x2)
+ /* 3-port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_3 UINT32_C(0x3)
+ /* 4-port device */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_4 UINT32_C(0x4)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_LAST \
+ HWRM_PORT_PHY_QCAPS_OUTPUT_PORT_CNT_4
+ /*
+ * This is a bit mask to indicate what speeds are supported
+ * as forced speeds on this link.
+ * For each speed that can be forced on this link, the
+ * corresponding mask bit shall be set to '1'.
+ */
+ uint16_t supported_speeds_force_mode;
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_2GB \
+ UINT32_C(0x10)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_FORCE_MODE_10MB \
+ UINT32_C(0x2000)
+ /*
+ * This is a bit mask to indicate what speeds are supported
+ * for autonegotiation on this link.
+ * For each speed that can be autonegotiated on this link, the
+ * corresponding mask bit shall be set to '1'.
+ */
+ uint16_t supported_speeds_auto_mode;
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_2GB \
+ UINT32_C(0x10)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_AUTO_MODE_10MB \
+ UINT32_C(0x2000)
+ /*
+ * This is a bit mask to indicate what speeds are supported
+ * for EEE on this link.
+ * For each speed that can be autonegotiated when EEE is enabled
+ * on this link, the corresponding mask bit shall be set to '1'.
+ * This field is only valid when the eee_suppotred is set to '1'.
+ */
+ uint16_t supported_speeds_eee_mode;
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_SPEEDS_EEE_MODE_10GB \
+ UINT32_C(0x40)
+ uint32_t tx_lpi_timer_low;
+ /*
+ * The lowest value of TX LPI timer that can be set on this link
+ * when EEE is enabled. This value is in microseconds.
+ * This field is valid only when_eee_supported is set to '1'.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_LOW_MASK \
+ UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_LOW_SFT 0
+ /*
+ * Reserved field. The HWRM shall set this field to 0.
+ * An HWRM client shall ignore this field.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD2_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD2_SFT 24
+ uint32_t valid_tx_lpi_timer_high;
+ /*
+ * The highest value of TX LPI timer that can be set on this link
+ * when EEE is enabled. This value is in microseconds.
+ * This field is valid only when_eee_supported is set to '1'.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_HIGH_MASK \
+ UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_TX_LPI_TIMER_HIGH_SFT 0
+ /*
+ * Reserved field. The HWRM shall set this field to 0.
+ * An HWRM client shall ignore this field.
+ */
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_RSVD_SFT 24
+ /*
+ * This field is used to advertise which PAM4 speeds are supported
+ * in auto mode.
+ */
+ uint16_t supported_pam4_speeds_auto_mode;
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_PAM4_SPEEDS_AUTO_MODE_50G \
+ UINT32_C(0x1)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_PAM4_SPEEDS_AUTO_MODE_100G \
+ UINT32_C(0x2)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_PAM4_SPEEDS_AUTO_MODE_200G \
+ UINT32_C(0x4)
+ /*
+ * This field is used to advertise which PAM4 speeds are supported
+ * in forced mode.
+ */
+ uint16_t supported_pam4_speeds_force_mode;
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_PAM4_SPEEDS_FORCE_MODE_50G \
+ UINT32_C(0x1)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_PAM4_SPEEDS_FORCE_MODE_100G \
+ UINT32_C(0x2)
+ #define HWRM_PORT_PHY_QCAPS_OUTPUT_SUPPORTED_PAM4_SPEEDS_FORCE_MODE_200G \
+ UINT32_C(0x4)
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/****************************
+ * hwrm_port_phy_mdio_write *
+ ****************************/
+
+
+/* hwrm_port_phy_mdio_write_input (size:320b/40B) */
+struct hwrm_port_phy_mdio_write_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Reserved for future use. */
+ uint32_t unused_0[2];
+ /* Port ID of port. */
+ uint16_t port_id;
+ /* If phy_address is 0xFF, port_id will be used to derive phy_addr. */
+ uint8_t phy_addr;
+ /* 8-bit device address. */
+ uint8_t dev_addr;
+ /* 16-bit register address. */
+ uint16_t reg_addr;
+ /* 16-bit register data. */
+ uint16_t reg_data;
+ /*
+ * When this bit is set to 1 a Clause 45 mdio access is done.
+ * when this bit is set to 0 a Clause 22 mdio access is done.
+ */
+ uint8_t cl45_mdio;
+ /* */
+ uint8_t unused_1[7];
+} __rte_packed;
+
+/* hwrm_port_phy_mdio_write_output (size:128b/16B) */
+struct hwrm_port_phy_mdio_write_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_port_phy_mdio_read *
+ ***************************/
+
+
+/* hwrm_port_phy_mdio_read_input (size:256b/32B) */
+struct hwrm_port_phy_mdio_read_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Reserved for future use. */
+ uint32_t unused_0[2];
+ /* Port ID of port. */
+ uint16_t port_id;
+ /* If phy_address is 0xFF, port_id will be used to derive phy_addr. */
+ uint8_t phy_addr;
+ /* 8-bit device address. */
+ uint8_t dev_addr;
+ /* 16-bit register address. */
+ uint16_t reg_addr;
+ /*
+ * When this bit is set to 1 a Clause 45 mdio access is done.
+ * when this bit is set to 0 a Clause 22 mdio access is done.
+ */
+ uint8_t cl45_mdio;
+ /* */
+ uint8_t unused_1;
+} __rte_packed;
+
+/* hwrm_port_phy_mdio_read_output (size:128b/16B) */
+struct hwrm_port_phy_mdio_read_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* 16-bit register data. */
+ uint16_t reg_data;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*********************
+ * hwrm_port_led_cfg *
+ *********************/
+
+
+/* hwrm_port_led_cfg_input (size:512b/64B) */
+struct hwrm_port_led_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the led0_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the led0_state field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_STATE \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the led0_color field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_COLOR \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the led0_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_ON \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the led0_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_OFF \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the led0_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_GROUP_ID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the led1_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_ID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the led1_state field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_STATE \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the led1_color field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_COLOR \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the led1_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_ON \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the led1_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_OFF \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the led1_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_GROUP_ID \
+ UINT32_C(0x800)
+ /*
+ * This bit must be '1' for the led2_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_ID \
+ UINT32_C(0x1000)
+ /*
+ * This bit must be '1' for the led2_state field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_STATE \
+ UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the led2_color field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_COLOR \
+ UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the led2_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_ON \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the led2_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_OFF \
+ UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the led2_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_GROUP_ID \
+ UINT32_C(0x20000)
+ /*
+ * This bit must be '1' for the led3_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_ID \
+ UINT32_C(0x40000)
+ /*
+ * This bit must be '1' for the led3_state field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_STATE \
+ UINT32_C(0x80000)
+ /*
+ * This bit must be '1' for the led3_color field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_COLOR \
+ UINT32_C(0x100000)
+ /*
+ * This bit must be '1' for the led3_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_ON \
+ UINT32_C(0x200000)
+ /*
+ * This bit must be '1' for the led3_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_OFF \
+ UINT32_C(0x400000)
+ /*
+ * This bit must be '1' for the led3_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_GROUP_ID \
+ UINT32_C(0x800000)
+ /* Port ID of port whose LEDs are configured. */
+ uint16_t port_id;
+ /*
+ * The number of LEDs that are being configured.
+ * Up to 4 LEDs can be configured with this command.
+ */
+ uint8_t num_leds;
+ /* Reserved field. */
+ uint8_t rsvd;
+ /* An identifier for the LED #0. */
+ uint8_t led0_id;
+ /* The requested state of the LED #0. */
+ uint8_t led0_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT
+ /* The requested color of LED #0. */
+ uint8_t led0_color;
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER
+ uint8_t unused_0;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led0_blink_on;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led0_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs
+ * to.
+ * If set to 0, then the LED #0 shall not be grouped and
+ * shall be treated as an individual resource.
+ * For all other non-zero values of this field, LED #0 shall
+ * be grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led0_group_id;
+ /* Reserved field. */
+ uint8_t rsvd0;
+ /* An identifier for the LED #1. */
+ uint8_t led1_id;
+ /* The requested state of the LED #1. */
+ uint8_t led1_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT
+ /* The requested color of LED #1. */
+ uint8_t led1_color;
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER
+ uint8_t unused_1;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led1_blink_on;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led1_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs
+ * to.
+ * If set to 0, then the LED #1 shall not be grouped and
+ * shall be treated as an individual resource.
+ * For all other non-zero values of this field, LED #1 shall
+ * be grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led1_group_id;
+ /* Reserved field. */
+ uint8_t rsvd1;
+ /* An identifier for the LED #2. */
+ uint8_t led2_id;
+ /* The requested state of the LED #2. */
+ uint8_t led2_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT
+ /* The requested color of LED #2. */
+ uint8_t led2_color;
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER
+ uint8_t unused_2;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led2_blink_on;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led2_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #2 belongs
+ * to.
+ * If set to 0, then the LED #2 shall not be grouped and
+ * shall be treated as an individual resource.
+ * For all other non-zero values of this field, LED #2 shall
+ * be grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led2_group_id;
+ /* Reserved field. */
+ uint8_t rsvd2;
+ /* An identifier for the LED #3. */
+ uint8_t led3_id;
+ /* The requested state of the LED #3. */
+ uint8_t led3_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT
+ /* The requested color of LED #3. */
+ uint8_t led3_color;
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_LAST \
+ HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER
+ uint8_t unused_3;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led3_blink_on;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led3_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs
+ * to.
+ * If set to 0, then the LED #3 shall not be grouped and
+ * shall be treated as an individual resource.
+ * For all other non-zero values of this field, LED #3 shall
+ * be grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led3_group_id;
+ /* Reserved field. */
+ uint8_t rsvd3;
+} __rte_packed;
+
+/* hwrm_port_led_cfg_output (size:128b/16B) */
+struct hwrm_port_led_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**********************
+ * hwrm_port_led_qcfg *
+ **********************/
+
+
+/* hwrm_port_led_qcfg_input (size:192b/24B) */
+struct hwrm_port_led_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port whose LED configuration is being queried. */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_port_led_qcfg_output (size:448b/56B) */
+struct hwrm_port_led_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * The number of LEDs that are configured on this port.
+ * Up to 4 LEDs can be returned in the response.
+ */
+ uint8_t num_leds;
+ /* An identifier for the LED #0. */
+ uint8_t led0_id;
+ /* The type of LED #0. */
+ uint8_t led0_type;
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID UINT32_C(0xff)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID
+ /* The current state of the LED #0. */
+ uint8_t led0_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT
+ /* The color of LED #0. */
+ uint8_t led0_color;
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER
+ uint8_t unused_0;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led0_blink_on;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led0_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs
+ * to.
+ * If set to 0, then the LED #0 is not grouped.
+ * For all other non-zero values of this field, LED #0 is
+ * grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led0_group_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_id;
+ /* The type of LED #1. */
+ uint8_t led1_type;
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID UINT32_C(0xff)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID
+ /* The current state of the LED #1. */
+ uint8_t led1_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT
+ /* The color of LED #1. */
+ uint8_t led1_color;
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER
+ uint8_t unused_1;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led1_blink_on;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led1_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs
+ * to.
+ * If set to 0, then the LED #1 is not grouped.
+ * For all other non-zero values of this field, LED #1 is
+ * grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led1_group_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_id;
+ /* The type of LED #2. */
+ uint8_t led2_type;
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID UINT32_C(0xff)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID
+ /* The current state of the LED #2. */
+ uint8_t led2_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT
+ /* The color of LED #2. */
+ uint8_t led2_color;
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER
+ uint8_t unused_2;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led2_blink_on;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led2_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #2 belongs
+ * to.
+ * If set to 0, then the LED #2 is not grouped.
+ * For all other non-zero values of this field, LED #2 is
+ * grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led2_group_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_id;
+ /* The type of LED #3. */
+ uint8_t led3_type;
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID UINT32_C(0xff)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID
+ /* The current state of the LED #3. */
+ uint8_t led3_state;
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT
+ /* The color of LED #3. */
+ uint8_t led3_color;
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_LAST \
+ HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER
+ uint8_t unused_3;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED on between cycles.
+ */
+ uint16_t led3_blink_on;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then
+ * this field represents the requested time in milliseconds
+ * to keep LED off between cycles.
+ */
+ uint16_t led3_blink_off;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs
+ * to.
+ * If set to 0, then the LED #3 is not grouped.
+ * For all other non-zero values of this field, LED #3 is
+ * grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led3_group_id;
+ uint8_t unused_4[6];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***********************
+ * hwrm_port_led_qcaps *
+ ***********************/
+
+
+/* hwrm_port_led_qcaps_input (size:192b/24B) */
+struct hwrm_port_led_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Port ID of port whose LED configuration is being queried. */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_port_led_qcaps_output (size:384b/48B) */
+struct hwrm_port_led_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * The number of LEDs that are configured on this port.
+ * Up to 4 LEDs can be returned in the response.
+ */
+ uint8_t num_leds;
+ /* Reserved for future use. */
+ uint8_t unused[3];
+ /* An identifier for the LED #0. */
+ uint8_t led0_id;
+ /* The type of LED #0. */
+ uint8_t led0_type;
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID UINT32_C(0xff)
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_LAST \
+ HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs
+ * to.
+ * If set to 0, then the LED #0 cannot be grouped.
+ * For all other non-zero values of this field, LED #0 is
+ * grouped together with the LEDs with the same group ID
+ * value.
+ */
+ uint8_t led0_group_id;
+ uint8_t unused_0;
+ /* The states supported by LED #0. */
+ uint16_t led0_state_caps;
+ /*
+ * If set to 1, this LED is enabled.
+ * If set to 0, this LED is disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ENABLED \