+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (80 bytes) */
+struct hwrm_func_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port that this function is associated with. Valid
+ * only for the PF. 0xFF... (All Fs) if this function is not
+ * associated with any port. 0xFF... (All Fs) if this function
+ * is called from a VF.
+ */
+ uint32_t flags;
+ /* If 1, then Push mode is supported on this function. */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PUSH_MODE_SUPPORTED UINT32_C(0x1)
+ /*
+ * If 1, then the global MSI-X auto-masking is enabled for the
+ * device.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_GLOBAL_MSIX_AUTOMASKING \
+ UINT32_C(0x2)
+ /*
+ * If 1, then the Precision Time Protocol (PTP) processing is
+ * supported on this function. The HWRM should enable PTP on
+ * only a single Physical Function (PF) per port.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_PTP_SUPPORTED UINT32_C(0x4)
+ /*
+ * If 1, then RDMA over Converged Ethernet (RoCE) v1 is
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V1_SUPPORTED UINT32_C(0x8)
+ /*
+ * If 1, then RDMA over Converged Ethernet (RoCE) v2 is
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_ROCE_V2_SUPPORTED UINT32_C(0x10)
+ /*
+ * If 1, then control and configuration of WoL magic packet are
+ * supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_MAGICPKT_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * If 1, then control and configuration of bitmap pattern packet
+ * are supported on this function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_WOL_BMP_SUPPORTED UINT32_C(0x40)
+ /*
+ * If set to 1, then the control and configuration of rate limit
+ * of an allocated TX ring on the queried function is supported.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_RING_RL_SUPPORTED UINT32_C(0x80)
+ /*
+ * If 1, then control and configuration of minimum and maximum
+ * bandwidths are supported on the queried function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_TX_BW_CFG_SUPPORTED UINT32_C(0x100)
+ /*
+ * If the query is for a VF, then this flag shall be ignored. If
+ * this query is for a PF and this flag is set to 1, then the PF
+ * has the capability to set the rate limits on the TX rings of
+ * its children VFs. If this query is for a PF and this flag is
+ * set to 0, then the PF does not have the capability to set the
+ * rate limits on the TX rings of its children VFs.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_TX_RING_RL_SUPPORTED \
+ UINT32_C(0x200)
+ /*
+ * If the query is for a VF, then this flag shall be ignored. If
+ * this query is for a PF and this flag is set to 1, then the PF
+ * has the capability to set the minimum and/or maximum
+ * bandwidths for its children VFs. If this query is for a PF
+ * and this flag is set to 0, then the PF does not have the
+ * capability to set the minimum or maximum bandwidths for its
+ * children VFs.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_VF_BW_CFG_SUPPORTED UINT32_C(0x400)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is supported on the
+ * queried function. If set to 0, then standard TX ring mode is
+ * not available on the queried function.
+ */
+ #define HWRM_FUNC_QCAPS_OUTPUT_FLAGS_STD_TX_RING_MODE_SUPPORTED \
+ UINT32_C(0x800)
+ uint8_t mac_address[6];
+ /*
+ * This value is current MAC address configured for this
+ * function. A value of 00-00-00-00-00-00 indicates no MAC
+ * address is currently configured.
+ */
+ uint16_t max_rsscos_ctx;
+ /*
+ * The maximum number of RSS/COS contexts that can be allocated
+ * to the function.
+ */
+ uint16_t max_cmpl_rings;
+ /*
+ * The maximum number of completion rings that can be allocated
+ * to the function.
+ */
+ uint16_t max_tx_rings;
+ /*
+ * The maximum number of transmit rings that can be allocated to
+ * the function.
+ */
+ uint16_t max_rx_rings;
+ /*
+ * The maximum number of receive rings that can be allocated to
+ * the function.
+ */
+ uint16_t max_l2_ctxs;
+ /*
+ * The maximum number of L2 contexts that can be allocated to
+ * the function.
+ */
+ uint16_t max_vnics;
+ /*
+ * The maximum number of VNICs that can be allocated to the
+ * function.
+ */
+ uint16_t first_vf_id;
+ /*
+ * The identifier for the first VF enabled on a PF. This is
+ * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
+ * this command is called on a PF with SR-IOV disabled or on a
+ * VF.
+ */
+ uint16_t max_vfs;
+ /*
+ * The maximum number of VFs that can be allocated to the
+ * function. This is valid only on the PF with SR-IOV enabled.
+ * 0xFF... (All Fs) if this command is called on a PF with SR-
+ * IOV disabled or on a VF.
+ */
+ uint16_t max_stat_ctx;
+ /*
+ * The maximum number of statistic contexts that can be
+ * allocated to the function.
+ */
+ uint32_t max_encap_records;
+ /*
+ * The maximum number of Encapsulation records that can be
+ * offloaded by this function.
+ */
+ uint32_t max_decap_records;
+ /*
+ * The maximum number of decapsulation records that can be
+ * offloaded by this function.
+ */
+ uint32_t max_tx_em_flows;
+ /*
+ * The maximum number of Exact Match (EM) flows that can be
+ * offloaded by this function on the TX side.
+ */
+ uint32_t max_tx_wm_flows;
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be
+ * offloaded by this function on the TX side.
+ */
+ uint32_t max_rx_em_flows;
+ /*
+ * The maximum number of Exact Match (EM) flows that can be
+ * offloaded by this function on the RX side.
+ */
+ uint32_t max_rx_wm_flows;
+ /*
+ * The maximum number of Wildcard Match (WM) flows that can be
+ * offloaded by this function on the RX side.
+ */
+ uint32_t max_mcast_filters;
+ /*
+ * The maximum number of multicast filters that can be supported
+ * by this function on the RX side.
+ */
+ uint32_t max_flow_id;
+ /*
+ * The maximum value of flow_id that can be supported in
+ * completion records.
+ */
+ uint32_t max_hw_ring_grps;
+ /*
+ * The maximum number of HW ring groups that can be supported on
+ * this function.
+ */
+ uint16_t max_sp_tx_rings;
+ /*
+ * The maximum number of strict priority transmit rings that can
+ * be allocated to the function. This number indicates the
+ * maximum number of TX rings that can be assigned strict
+ * priorities out of the maximum number of TX rings that can be
+ * allocated (max_tx_rings) to the function.
+ */
+ uint8_t unused_0;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qcfg */
+/*
+ * Description: This command returns the current configuration of a function.
+ * The input FID value is used to indicate what function is being queried. This
+ * allows a physical function driver to query virtual functions that are
+ * children of the physical function. The output FID value is needed to
+ * configure Rings and MSI-X vectors so their DMA operations appear correctly on
+ * the PCI bus. This command should be called by every driver after
+ * 'hwrm_func_cfg' to get the actual number of resources allocated by the HWRM.
+ * The values returned by hwrm_func_qcfg are the values the driver shall use.
+ * These values may be different than what was originally requested in the
+ * 'hwrm_func_cfg' command.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (72 bytes) */
+struct hwrm_func_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t fid;
+ /*
+ * FID value. This value is used to identify operations on the
+ * PCI bus as belonging to a particular PCI function.
+ */
+ uint16_t port_id;
+ /*
+ * Port ID of port that this function is associated with.
+ * 0xFF... (All Fs) if this function is not associated with any
+ * port.
+ */
+ uint16_t vlan;
+ /*
+ * This value is the current VLAN setting for this function. The
+ * value of 0 for this field indicates no priority tagging or
+ * VLAN is used. This field's format is same as 802.1Q Tag's Tag
+ * Control Information (TCI) format that includes both Priority
+ * Code Point (PCP) and VLAN Identifier (VID).
+ */
+ uint16_t flags;
+ /*
+ * If 1, then magic packet based Out-Of-Box WoL is enabled on
+ * the port associated with this function.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_MAGICPKT_ENABLED \
+ UINT32_C(0x1)
+ /*
+ * If 1, then bitmap pattern based Out-Of-Box WoL packet is
+ * enabled on the port associated with this function.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_OOB_WOL_BMP_ENABLED UINT32_C(0x2)
+ /*
+ * If set to 1, then FW based DCBX agent is enabled and running
+ * on the port associated with this function. If set to 0, then
+ * DCBX agent is not running in the firmware.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_DCBX_AGENT_ENABLED \
+ UINT32_C(0x4)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is enabled on the
+ * queried function. If set to 0, then the standard TX ring mode
+ * is disabled on the queried function. In this extended TX ring
+ * resource mode, the minimum and maximum bandwidth settings are
+ * not supported to allow the allocation of TX rings to span
+ * multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_STD_TX_RING_MODE_ENABLED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1 then FW based LLDP agent is enabled and running
+ * on the port associated with this function. If set to 0 then
+ * the LLDP agent is not running in the firmware.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_FW_LLDP_AGENT_ENABLED UINT32_C(0x10)
+ /*
+ * If set to 1, then multi-host mode is active for this
+ * function. If set to 0, then multi-host mode is inactive for
+ * this function or not applicable for this device.
+ */
+ #define HWRM_FUNC_QCFG_OUTPUT_FLAGS_MULTI_HOST UINT32_C(0x20)
+ uint8_t mac_address[6];
+ /*
+ * This value is current MAC address configured for this
+ * function. A value of 00-00-00-00-00-00 indicates no MAC
+ * address is currently configured.
+ */
+ uint16_t pci_id;
+ /*
+ * This value is current PCI ID of this function. If ARI is
+ * enabled, then it is Bus Number (8b):Function Number(8b).
+ * Otherwise, it is Bus Number (8b):Device Number (4b):Function
+ * Number(4b).
+ */
+ uint16_t alloc_rsscos_ctx;
+ /*
+ * The number of RSS/COS contexts currently allocated to the
+ * function.
+ */
+ uint16_t alloc_cmpl_rings;
+ /*
+ * The number of completion rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_tx_rings;
+ /*
+ * The number of transmit rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_rx_rings;
+ /*
+ * The number of receive rings currently allocated to the
+ * function. This does not include the rings allocated to any
+ * children functions if any.
+ */
+ uint16_t alloc_l2_ctx;
+ /* The allocated number of L2 contexts to the function. */
+ uint16_t alloc_vnics;
+ /* The allocated number of vnics to the function. */
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. For rings
+ * allocated on this function, this default value is used if
+ * ring MTU is not specified.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. For vnics allocated
+ * on this function, this default value is used if vnic MRU is
+ * not specified.
+ */
+ uint16_t stat_ctx_id;
+ /* The statistics context assigned to a function. */
+ uint8_t port_partition_type;
+ /*
+ * The HWRM shall return Unknown value for this field when this
+ * command is used to query VF's configuration.
+ */
+ /* Single physical function */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_SPF UINT32_C(0x0)
+ /* Multiple physical functions */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_MPFS UINT32_C(0x1)
+ /* Network Partitioning 1.0 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_0 UINT32_C(0x2)
+ /* Network Partitioning 1.5 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR1_5 UINT32_C(0x3)
+ /* Network Partitioning 2.0 */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_NPAR2_0 UINT32_C(0x4)
+ /* Unknown */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PARTITION_TYPE_UNKNOWN UINT32_C(0xff)
+ uint8_t port_pf_cnt;
+ /*
+ * This field will indicate number of physical functions on this
+ * port_partition. HWRM shall return unavail (i.e. value of 0)
+ * for this field when this command is used to query VF's
+ * configuration or from older firmware that doesn't support
+ * this field.
+ */
+ /* number of PFs is not available */
+ #define HWRM_FUNC_QCFG_OUTPUT_PORT_PF_CNT_UNAVAIL UINT32_C(0x0)
+ uint16_t dflt_vnic_id;
+ /* The default VNIC ID assigned to a function that is being queried. */
+ uint16_t max_mtu_configured;
+ /*
+ * This value specifies the MAX MTU that can be configured by
+ * host drivers. This 'max_mtu_configure' can be HW max MTU or
+ * OEM applications specified value. Host drivers can't
+ * configure the MTU greater than this value. Host drivers
+ * should read this value prior to configuring the MTU. FW will
+ * fail the host request with MTU greater than
+ * 'max_mtu_configured'.
+ */
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device. A value of 0 indicates
+ * the minimum bandwidth is not configured.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_SCALE_LAST \
+ FUNC_QCFG_OUTPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_QCFG_OUTPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device. A value of 0 indicates
+ * that the maximum bandwidth is not configured.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_SCALE_LAST \
+ FUNC_QCFG_OUTPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_QCFG_OUTPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t evb_mode;
+ /*
+ * This value indicates the Edge virtual bridge mode for the
+ * domain that this function belongs to.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEB UINT32_C(0x1)
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_QCFG_OUTPUT_EVB_MODE_VEPA UINT32_C(0x2)
+ uint8_t unused_0;
+ uint16_t alloc_vfs;
+ /*
+ * The number of VFs that are allocated to the function. This is
+ * valid only on the PF with SR-IOV enabled. 0xFF... (All Fs) if
+ * this command is called on a PF with SR-IOV disabled or on a
+ * VF.
+ */
+ uint32_t alloc_mcast_filters;
+ /*
+ * The number of allocated multicast filters for this function
+ * on the RX side.
+ */
+ uint32_t alloc_hw_ring_grps;
+ /* The number of allocated HW ring groups for this function. */
+ uint16_t alloc_sp_tx_rings;
+ /*
+ * The number of strict priority transmit rings out of currently
+ * allocated TX rings to the function (alloc_tx_rings).
+ */
+ uint8_t unused_1;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vlan_qcfg */
+/*
+ * Description: This command should be called by PF driver to get the current
+ * C-TAG, S-TAG and correcponsing PCP and TPID values configured for the
+ * function.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_vlan_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the configuration is for the
+ * requesting function.
+ */
+ uint16_t unused_0[3];
+};
+
+/* Output (40 bytes) */
+struct hwrm_func_vlan_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+ uint16_t stag_vid;
+ /* S-TAG VLAN identifier configured for the function. */
+ uint8_t stag_pcp;
+ /* S-TAG PCP value configured for the function. */
+ uint8_t unused_4;
+ uint16_t stag_tpid;
+ /*
+ * S-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint16_t ctag_vid;
+ /* C-TAG VLAN identifier configured for the function. */
+ uint8_t ctag_pcp;
+ /* C-TAG PCP value configured for the function. */
+ uint8_t unused_5;
+ uint16_t ctag_tpid;
+ /*
+ * C-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint32_t rsvd2;
+ /* Future use. */
+ uint32_t rsvd3;
+ /* Future use. */
+ uint32_t unused_6;
+};
+
+/* hwrm_func_vlan_cfg */
+/*
+ * Description: This command allows PF driver to configure C-TAG, S-TAG and
+ * corresponding PCP and TPID values for a function.
+ */
+/* Input (48 bytes) */
+struct hwrm_func_vlan_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t enables;
+ /* This bit must be '1' for the stag_vid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_VID UINT32_C(0x1)
+ /* This bit must be '1' for the ctag_vid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_VID UINT32_C(0x2)
+ /* This bit must be '1' for the stag_pcp field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_PCP UINT32_C(0x4)
+ /* This bit must be '1' for the ctag_pcp field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_PCP UINT32_C(0x8)
+ /* This bit must be '1' for the stag_tpid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_STAG_TPID UINT32_C(0x10)
+ /* This bit must be '1' for the ctag_tpid field to be configured. */
+ #define HWRM_FUNC_VLAN_CFG_INPUT_ENABLES_CTAG_TPID UINT32_C(0x20)
+ uint16_t stag_vid;
+ /* S-TAG VLAN identifier configured for the function. */
+ uint8_t stag_pcp;
+ /* S-TAG PCP value configured for the function. */
+ uint8_t unused_2;
+ uint16_t stag_tpid;
+ /*
+ * S-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint16_t ctag_vid;
+ /* C-TAG VLAN identifier configured for the function. */
+ uint8_t ctag_pcp;
+ /* C-TAG PCP value configured for the function. */
+ uint8_t unused_3;
+ uint16_t ctag_tpid;
+ /*
+ * C-TAG TPID value configured for the function. This field is
+ * specified in network byte order.
+ */
+ uint32_t rsvd1;
+ /* Future use. */
+ uint32_t rsvd2;
+ /* Future use. */
+ uint32_t unused_4;
+};
+
+/* Output (16 bytes) */
+struct hwrm_func_vlan_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+};
+
+/* hwrm_func_cfg */
+/*
+ * Description: This command allows configuration of a PF by the corresponding
+ * PF driver. This command also allows configuration of a child VF by its parent
+ * PF driver. The input FID value is used to indicate what function is being
+ * configured. This allows a PF driver to configure the PF owned by itself or a
+ * virtual function that is a child of the PF. This command allows to reserve
+ * resources for a VF by its parent PF. To reverse the process, the command
+ * should be called with all enables flags cleared for resources. This will free
+ * allocated resources for the VF and return them to the resource pool. If this
+ * command is requested by a VF driver to configure or reserve resources, then
+ * the HWRM shall fail this command. If default MAC address and/or VLAN are
+ * provided in this command, then the HWRM shall set up appropriate MAC/VLAN
+ * filters for the function that is being configured. If source properties
+ * checks are enabled and default MAC address and/or IP address are provided in
+ * this command, then the HWRM shall set appropriate source property checks
+ * based on provided MAC and/or IP addresses. The parent PF driver should not
+ * set MTU/MRU for a VF using this command. This is to allow MTU/MRU setting by
+ * the VF driver. If the MTU or MRU for a VF is set by the PF driver, then the
+ * HWRM should ignore it. A function's MTU/MRU should be set prior to allocating
+ * RX VNICs or TX rings. A PF driver calls hwrm_func_cfg to allocate resources
+ * for itself or its children VFs. All function drivers shall call hwrm_func_cfg
+ * to reserve resources. A request to hwrm_func_cfg may not be fully granted;
+ * that is, a request for resources may be larger than what can be supported by
+ * the device and the HWRM will allocate the best set of resources available,
+ * but that may be less than requested. If all the amounts requested could not
+ * be fulfilled, the HWRM shall allocate what it could and return a status code
+ * of success. A function driver should call hwrm_func_qcfg immediately after
+ * hwrm_func_cfg to determine what resources were assigned to the configured
+ * function. A call by a PF driver to hwrm_func_cfg to allocate resources for
+ * itself shall only allocate resources for the PF driver to use, not for its
+ * children VFs. Likewise, a call to hwrm_func_qcfg shall return the resources
+ * available for the PF driver to use, not what is available to its children
+ * VFs.
+ */
+/* Input (88 bytes) */
+struct hwrm_func_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. If set
+ * to 0xFF... (All Fs), then the the configuration is for the
+ * requesting function.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function is disabled with source
+ * MAC address check. This is an anti-spoofing check. If this
+ * flag is set, then the function shall be configured to
+ * disallow transmission of frames with the source MAC address
+ * that is configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_DISABLE \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is enabled with source MAC
+ * address check. This is an anti-spoofing check. If this flag
+ * is set, then the function shall be configured to allow
+ * transmission of frames with the source MAC address that is
+ * configured for this function.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_SRC_MAC_ADDR_CHECK_ENABLE \
+ UINT32_C(0x2)
+ /* reserved */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_MASK UINT32_C(0x1fc)
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_RSVD_SFT 2
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then standard TX ring mode is requested to be
+ * enabled on the function being configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_ENABLE \
+ UINT32_C(0x200)
+ /*
+ * Standard TX Ring mode is used for the allocation of TX ring
+ * and underlying scheduling resources that allow bandwidth
+ * reservation and limit settings on the queried function. If
+ * set to 1, then the standard TX ring mode is requested to be
+ * disabled on the function being configured. In this extended
+ * TX ring resource mode, the minimum and maximum bandwidth
+ * settings are not supported to allow the allocation of TX
+ * rings to span multiple scheduler nodes.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_STD_TX_RING_MODE_DISABLE \
+ UINT32_C(0x400)
+ /*
+ * If this bit is set, virtual mac address configured in this
+ * command will be persistent over warm boot.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_VIRT_MAC_PERSIST UINT32_C(0x800)
+ /*
+ * This bit only applies to the VF. If this bit is set, the
+ * statistic context counters will not be cleared when the
+ * statistic context is freed or a function reset is called on
+ * VF. This bit will be cleared when the PF is unloaded or a
+ * function reset is called on the PF.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_NO_AUTOCLEAR_STATISTIC \
+ UINT32_C(0x1000)
+ /*
+ * This bit requests that the firmware test to see if all the
+ * assets requested in this command (i.e. number of TX rings)
+ * are available. The firmware will return an error if the
+ * requested assets are not available. The firwmare will NOT
+ * reserve the assets if they are available.
+ */
+ #define HWRM_FUNC_CFG_INPUT_FLAGS_TX_ASSETS_TEST UINT32_C(0x2000)
+ uint32_t enables;
+ /* This bit must be '1' for the mtu field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MTU UINT32_C(0x1)
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MRU UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the num_rsscos_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RSSCOS_CTXS UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the num_cmpl_rings field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_CMPL_RINGS UINT32_C(0x8)
+ /* This bit must be '1' for the num_tx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_TX_RINGS UINT32_C(0x10)
+ /* This bit must be '1' for the num_rx_rings field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_RX_RINGS UINT32_C(0x20)
+ /* This bit must be '1' for the num_l2_ctxs field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_L2_CTXS UINT32_C(0x40)
+ /* This bit must be '1' for the num_vnics field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_VNICS UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the num_stat_ctxs field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_STAT_CTXS UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the dflt_mac_addr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_MAC_ADDR UINT32_C(0x200)
+ /* This bit must be '1' for the dflt_vlan field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_VLAN UINT32_C(0x400)
+ /* This bit must be '1' for the dflt_ip_addr field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_DFLT_IP_ADDR UINT32_C(0x800)
+ /* This bit must be '1' for the min_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MIN_BW UINT32_C(0x1000)
+ /* This bit must be '1' for the max_bw field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_MAX_BW UINT32_C(0x2000)
+ /*
+ * This bit must be '1' for the async_event_cr field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ASYNC_EVENT_CR UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the vlan_antispoof_mode field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_VLAN_ANTISPOOF_MODE UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the allowed_vlan_pris field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_ALLOWED_VLAN_PRIS UINT32_C(0x10000)
+ /* This bit must be '1' for the evb_mode field to be configured. */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_EVB_MODE UINT32_C(0x20000)
+ /*
+ * This bit must be '1' for the num_mcast_filters field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_MCAST_FILTERS UINT32_C(0x40000)
+ /*
+ * This bit must be '1' for the num_hw_ring_grps field to be
+ * configured.
+ */
+ #define HWRM_FUNC_CFG_INPUT_ENABLES_NUM_HW_RING_GRPS UINT32_C(0x80000)
+ uint16_t mtu;
+ /*
+ * The maximum transmission unit of the function. The HWRM
+ * should make sure that the mtu of the function does not exceed
+ * the mtu of the physical port that this function is associated
+ * with. In addition to configuring mtu per function, it is
+ * possible to configure mtu per transmit ring. By default, the
+ * mtu of each transmit ring associated with a function is equal
+ * to the mtu of the function. The HWRM should make sure that
+ * the mtu of each transmit ring that is assigned to a function
+ * has a valid mtu.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the function. The HWRM should
+ * make sure that the mru of the function does not exceed the
+ * mru of the physical port that this function is associated
+ * with. In addition to configuring mru per function, it is
+ * possible to configure mru per vnic. By default, the mru of
+ * each vnic associated with a function is equal to the mru of
+ * the function. The HWRM should make sure that the mru of each
+ * vnic that is assigned to a function has a valid mru.
+ */
+ uint16_t num_rsscos_ctxs;
+ /* The number of RSS/COS contexts requested for the function. */
+ uint16_t num_cmpl_rings;
+ /*
+ * The number of completion rings requested for the function.
+ * This does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_tx_rings;
+ /*
+ * The number of transmit rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_rx_rings;
+ /*
+ * The number of receive rings requested for the function. This
+ * does not include the rings allocated to any children
+ * functions if any.
+ */
+ uint16_t num_l2_ctxs;
+ /* The requested number of L2 contexts for the function. */
+ uint16_t num_vnics;
+ /* The requested number of vnics for the function. */
+ uint16_t num_stat_ctxs;
+ /* The requested number of statistic contexts for the function. */
+ uint16_t num_hw_ring_grps;
+ /*
+ * The number of HW ring groups that should be reserved for this
+ * function.
+ */
+ uint8_t dflt_mac_addr[6];
+ /* The default MAC address for the function being configured. */
+ uint16_t dflt_vlan;
+ /*
+ * The default VLAN for the function being configured. This
+ * field's format is same as 802.1Q Tag's Tag Control
+ * Information (TCI) format that includes both Priority Code
+ * Point (PCP) and VLAN Identifier (VID).
+ */
+ uint32_t dflt_ip_addr[4];
+ /*
+ * The default IP address for the function being configured.
+ * This address is only used in enabling source property check.
+ */
+ uint32_t min_bw;
+ /*
+ * Minimum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MIN_BW_BW_VALUE_UNIT_INVALID
+ uint32_t max_bw;
+ /*
+ * Maximum BW allocated for this function. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for the scheduler inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_SCALE_LAST \
+ FUNC_CFG_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ FUNC_CFG_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint16_t async_event_cr;
+ /*
+ * ID of the target completion ring for receiving asynchronous
+ * event completions. If this field is not valid, then the HWRM
+ * shall use the default completion ring of the function that is
+ * being configured as the target completion ring for providing
+ * any asynchronous event completions for that function. If this
+ * field is valid, then the HWRM shall use the completion ring
+ * identified by this ID as the target completion ring for
+ * providing any asynchronous event completions for the function
+ * that is being configured.
+ */
+ uint8_t vlan_antispoof_mode;
+ /* VLAN Anti-spoofing mode. */
+ /* No VLAN anti-spoofing checks are enabled */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_NOCHECK UINT32_C(0x0)
+ /* Validate VLAN against the configured VLAN(s) */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_VALIDATE_VLAN \
+ UINT32_C(0x1)
+ /* Insert VLAN if it does not exist, otherwise discard */
+ #define HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_IF_VLANDNE \
+ UINT32_C(0x2)
+ /*
+ * Insert VLAN if it does not exist, override
+ * VLAN if it exists
+ */
+ #define \
+ HWRM_FUNC_CFG_INPUT_VLAN_ANTISPOOF_MODE_INSERT_OR_OVERRIDE_VLAN \
+ UINT32_C(0x3)
+ uint8_t allowed_vlan_pris;
+ /*
+ * This bit field defines VLAN PRIs that are allowed on this
+ * function. If nth bit is set, then VLAN PRI n is allowed on
+ * this function.
+ */
+ uint8_t evb_mode;
+ /*
+ * The HWRM shall allow a PF driver to change EVB mode for the
+ * partition it belongs to. The HWRM shall not allow a VF driver
+ * to change the EVB mode. The HWRM shall take into account the
+ * switching of EVB mode from one to another and reconfigure
+ * hardware resources as appropriately. The switching from VEB
+ * to VEPA mode requires the disabling of the loopback traffic.
+ * Additionally, source knock outs are handled differently in
+ * VEB and VEPA modes.
+ */
+ /* No Edge Virtual Bridging (EVB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_NO_EVB UINT32_C(0x0)
+ /* Virtual Ethernet Bridge (VEB) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEB UINT32_C(0x1)
+ /* Virtual Ethernet Port Aggregator (VEPA) */
+ #define HWRM_FUNC_CFG_INPUT_EVB_MODE_VEPA UINT32_C(0x2)
+ uint8_t unused_2;
+ uint16_t num_mcast_filters;
+ /*
+ * The number of multicast filters that should be reserved for
+ * this function on the RX side.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_qstats */
+/*
+ * Description: This command returns statistics of a function. The input FID
+ * value is used to indicate what function is being queried. This allows a
+ * physical function driver to query virtual functions that are children of the
+ * physical function. The HWRM shall return any unsupported counter with a value
+ * of 0xFFFFFFFF for 32-bit counters and 0xFFFFFFFFFFFFFFFF for 64-bit counters.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being queried. 0xFF...
+ * (All Fs) if the query is for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (176 bytes) */
+struct hwrm_func_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t tx_ucast_pkts;
+ /* Number of transmitted unicast packets on the function. */
+ uint64_t tx_mcast_pkts;
+ /* Number of transmitted multicast packets on the function. */
+ uint64_t tx_bcast_pkts;
+ /* Number of transmitted broadcast packets on the function. */
+ uint64_t tx_err_pkts;
+ /*
+ * Number of transmitted packets that were discarded due to
+ * internal NIC resource problems. For transmit, this can only
+ * happen if TMP is configured to allow dropping in HOL blocking
+ * conditions, which is not a normal configuration.
+ */
+ uint64_t tx_drop_pkts;
+ /*
+ * Number of dropped packets on transmit path on the function.
+ * These are packets that have been marked for drop by the TE
+ * CFA block or are packets that exceeded the transmit MTU limit
+ * for the function.
+ */
+ uint64_t tx_ucast_bytes;
+ /* Number of transmitted bytes for unicast traffic on the function. */
+ uint64_t tx_mcast_bytes;
+ /*
+ * Number of transmitted bytes for multicast traffic on the
+ * function.
+ */
+ uint64_t tx_bcast_bytes;
+ /*
+ * Number of transmitted bytes for broadcast traffic on the
+ * function.
+ */
+ uint64_t rx_ucast_pkts;
+ /* Number of received unicast packets on the function. */
+ uint64_t rx_mcast_pkts;
+ /* Number of received multicast packets on the function. */
+ uint64_t rx_bcast_pkts;
+ /* Number of received broadcast packets on the function. */
+ uint64_t rx_err_pkts;
+ /*
+ * Number of received packets that were discarded on the
+ * function due to resource limitations. This can happen for 3
+ * reasons. # The BD used for the packet has a bad format. #
+ * There were no BDs available in the ring for the packet. #
+ * There were no BDs available on-chip for the packet.
+ */
+ uint64_t rx_drop_pkts;
+ /*
+ * Number of dropped packets on received path on the function.
+ * These are packets that have been marked for drop by the RE
+ * CFA.
+ */
+ uint64_t rx_ucast_bytes;
+ /* Number of received bytes for unicast traffic on the function. */
+ uint64_t rx_mcast_bytes;
+ /* Number of received bytes for multicast traffic on the function. */
+ uint64_t rx_bcast_bytes;
+ /* Number of received bytes for broadcast traffic on the function. */
+ uint64_t rx_agg_pkts;
+ /* Number of aggregated unicast packets on the function. */
+ uint64_t rx_agg_bytes;
+ /* Number of aggregated unicast bytes on the function. */
+ uint64_t rx_agg_events;
+ /* Number of aggregation events on the function. */
+ uint64_t rx_agg_aborts;
+ /* Number of aborted aggregations on the function. */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_clr_stats */
+/*
+ * Description: This command clears statistics of a function. The input FID
+ * value is used to indicate what function's statistics is being cleared. This
+ * allows a physical function driver to clear statistics of virtual functions
+ * that are children of the physical function.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function. 0xFF... (All Fs) if the query is
+ * for the requesting function.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_vf_vnic_ids_query */
+/* Description: This command is used to query vf vnic ids. */
+/* Input (32 bytes) */
+struct hwrm_func_vf_vnic_ids_query_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t max_vnic_id_cnt;
+ /* Max number of vnic ids in vnic id table */
+ uint64_t vnic_id_tbl_addr;
+ /* This is the address for VF VNIC ID table */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_vf_vnic_ids_query_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t vnic_id_cnt;
+ /*
+ * Actual number of vnic ids Each VNIC ID is written as a 32-bit
+ * number.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_rgtr */
+/*
+ * Description: This command is used by the function driver to register its
+ * information with the HWRM. A function driver shall implement this command. A
+ * function driver shall use this command during the driver initialization right
+ * after the HWRM version discovery and default ring resources allocation.
+ */
+/* Input (80 bytes) */
+struct hwrm_func_drv_rgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function driver is requesting all
+ * requests from its children VF drivers to be forwarded to
+ * itself. This flag can only be set by the PF driver. If a VF
+ * driver sets this flag, it should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_ALL_MODE UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is requesting none of the
+ * requests from its children VF drivers to be forwarded to
+ * itself. This flag can only be set by the PF driver. If a VF
+ * driver sets this flag, it should be ignored by the HWRM.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_FLAGS_FWD_NONE_MODE UINT32_C(0x2)
+ uint32_t enables;
+ /* This bit must be '1' for the os_type field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_OS_TYPE UINT32_C(0x1)
+ /* This bit must be '1' for the ver field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VER UINT32_C(0x2)
+ /* This bit must be '1' for the timestamp field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_TIMESTAMP UINT32_C(0x4)
+ /* This bit must be '1' for the vf_req_fwd field to be configured. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_VF_INPUT_FWD UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the async_event_fwd field to be
+ * configured.
+ */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_ENABLES_ASYNC_EVENT_FWD UINT32_C(0x10)
+ uint16_t os_type;
+ /*
+ * This value indicates the type of OS. The values are based on
+ * CIM_OperatingSystem.mof file as published by the DMTF.
+ */
+ /* Unknown */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_UNKNOWN UINT32_C(0x0)
+ /* Other OS not listed below. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_OTHER UINT32_C(0x1)
+ /* MSDOS OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_MSDOS UINT32_C(0xe)
+ /* Windows OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WINDOWS UINT32_C(0x12)
+ /* Solaris OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_SOLARIS UINT32_C(0x1d)
+ /* Linux OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_LINUX UINT32_C(0x24)
+ /* FreeBSD OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_FREEBSD UINT32_C(0x2a)
+ /* VMware ESXi OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_ESXI UINT32_C(0x68)
+ /* Microsoft Windows 8 64-bit OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN864 UINT32_C(0x73)
+ /* Microsoft Windows Server 2012 R2 OS. */
+ #define HWRM_FUNC_DRV_RGTR_INPUT_OS_TYPE_WIN2012R2 UINT32_C(0x74)
+ uint8_t ver_maj;
+ /* This is the major version of the driver. */
+ uint8_t ver_min;
+ /* This is the minor version of the driver. */
+ uint8_t ver_upd;
+ /* This is the update version of the driver. */
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t timestamp;
+ /*
+ * This is a 32-bit timestamp provided by the driver for keep
+ * alive. The timestamp is in multiples of 1ms.
+ */
+ uint32_t unused_2;
+ uint32_t vf_req_fwd[8];
+ /*
+ * This is a 256-bit bit mask provided by the PF driver for
+ * letting the HWRM know what commands issued by the VF driver
+ * to the HWRM should be forwarded to the PF driver. Nth bit
+ * refers to the Nth req_type. Setting Nth bit to 1 indicates
+ * that requests from the VF driver with req_type equal to N
+ * shall be forwarded to the parent PF driver. This field is not
+ * valid for the VF driver.
+ */
+ uint32_t async_event_fwd[8];
+ /*
+ * This is a 256-bit bit mask provided by the function driver
+ * (PF or VF driver) to indicate the list of asynchronous event
+ * completions to be forwarded. Nth bit refers to the Nth
+ * event_id. Setting Nth bit to 1 by the function driver shall
+ * result in the HWRM forwarding asynchronous event completion
+ * with event_id equal to N. If all bits are set to 0 (value of
+ * 0), then the HWRM shall not forward any asynchronous event
+ * completion to this function driver.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_rgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_drv_unrgtr */
+/*
+ * Description: This command is used by the function driver to un register with
+ * the HWRM. A function driver shall implement this command. A function driver
+ * shall use this command during the driver unloading.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_drv_unrgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the function driver is notifying the
+ * HWRM to prepare for the shutdown.
+ */
+ #define HWRM_FUNC_DRV_UNRGTR_INPUT_FLAGS_PREPARE_FOR_SHUTDOWN \
+ UINT32_C(0x1)
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_drv_unrgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_buf_rgtr */
+/*
+ * Description: This command is used by the PF driver to register buffers used
+ * in the PF-VF communication with the HWRM. The PF driver uses this command to
+ * register buffers for each PF-VF channel. A parent PF may issue this command
+ * per child VF. If VF ID is not valid, then this command is used to register
+ * buffers for all children VFs of the PF.
+ */
+/* Input (128 bytes) */
+struct hwrm_func_buf_rgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id field to be configured. */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_VF_ID UINT32_C(0x1)
+ /* This bit must be '1' for the err_buf_addr field to be configured. */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_ENABLES_ERR_BUF_ADDR UINT32_C(0x2)
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t req_buf_num_pages;
+ /*
+ * This field represents the number of pages used for request
+ * buffer(s).
+ */
+ uint16_t req_buf_page_size;
+ /* This field represents the page size used for request buffer(s). */
+ /* 16 bytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_16B UINT32_C(0x4)
+ /* 4 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4K UINT32_C(0xc)
+ /* 8 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_8K UINT32_C(0xd)
+ /* 64 Kbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_64K UINT32_C(0x10)
+ /* 2 Mbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_2M UINT32_C(0x15)
+ /* 4 Mbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_4M UINT32_C(0x16)
+ /* 1 Gbytes */
+ #define HWRM_FUNC_BUF_RGTR_INPUT_INPUT_BUF_PAGE_SIZE_1G UINT32_C(0x1e)
+ uint16_t req_buf_len;
+ /* The length of the request buffer per VF in bytes. */
+ uint16_t resp_buf_len;
+ /* The length of the response buffer in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint64_t req_buf_page_addr[10];
+ /* This field represents the page address of req buffer. */
+ uint64_t error_buf_addr;
+ /*
+ * This field is used to receive the error reporting from the
+ * chipset. Only applicable for PFs.
+ */
+ uint64_t resp_buf_addr;
+ /* This field is used to receive the response forwarded by the HWRM. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_buf_rgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_func_buf_unrgtr */
+/*
+ * Description: This command is used by the PF driver to unregister buffers used
+ * in the PF-VF communication with the HWRM. The PF driver uses this command to
+ * unregister buffers for PF-VF communication. A parent PF may issue this
+ * command to unregister buffers for communication between the PF and a specific
+ * VF. If the VF ID is not valid, then this command is used to unregister
+ * buffers used for communications with all children VFs of the PF.
+ */
+/* Input (24 bytes) */
+struct hwrm_func_buf_unrgtr_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id field to be configured. */
+ #define HWRM_FUNC_BUF_UNRGTR_INPUT_ENABLES_VF_ID UINT32_C(0x1)
+ uint16_t vf_id;
+ /*
+ * This value is used to identify a Virtual Function (VF). The
+ * scope of VF ID is local within a PF.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_func_buf_unrgtr_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_cfg */
+/*
+ * Description: This command configures the PHY device for the port. It allows
+ * setting of the most generic settings for the PHY. The HWRM shall complete
+ * this command as soon as PHY settings are configured. They may not be applied
+ * when the command response is provided. A VF driver shall not be allowed to
+ * configure PHY using this command. In a network partition mode, a PF driver
+ * shall not be allowed to configure PHY using this command.
+ */
+/* Input (56 bytes) */
+struct hwrm_port_phy_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is set to '1', the PHY for the port shall be
+ * reset. # If this bit is set to 1, then the HWRM shall reset
+ * the PHY after applying PHY configuration changes specified in
+ * this command. # In order to guarantee that PHY configuration
+ * changes specified in this command take effect, the HWRM
+ * client should set this flag to 1. # If this bit is not set to
+ * 1, then the HWRM may reset the PHY depending on the current
+ * PHY configuration and settings specified in this command.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY UINT32_C(0x1)
+ /* deprecated bit. Do not use!!! */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_DEPRECATED UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', the link shall be forced to the
+ * force_link_speed value. When this bit is set to '1', the HWRM
+ * client should not enable any of the auto negotiation related
+ * fields represented by auto_XXX fields in this command. When
+ * this bit is set to '1' and the HWRM client has enabled a
+ * auto_XXX field in this command, then the HWRM shall ignore
+ * the enabled auto_XXX field. When this bit is set to zero, the
+ * link shall be allowed to autoneg.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', the auto-negotiation process
+ * shall be restarted on the link.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE)
+ * is requested to be enabled on this link. If EEE is not
+ * supported on this port, then this flag shall be ignored by
+ * the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_ENABLE UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', Energy Efficient Ethernet (EEE)
+ * is requested to be disabled on this link. If EEE is not
+ * supported on this port, then this flag shall be ignored by
+ * the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_DISABLE UINT32_C(0x20)
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link,
+ * then TX LPI is requested to be enabled on the link. If EEE is
+ * not supported on this port, then this flag shall be ignored
+ * by the HWRM. If EEE is disabled on this port, then this flag
+ * shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_ENABLE UINT32_C(0x40)
+ /*
+ * When this bit is set to '1' and EEE is enabled on this link,
+ * then TX LPI is requested to be disabled on the link. If EEE
+ * is not supported on this port, then this flag shall be
+ * ignored by the HWRM. If EEE is disabled on this port, then
+ * this flag shall be ignored by the HWRM.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_EEE_TX_LPI_DISABLE UINT32_C(0x80)
+ /*
+ * When set to 1, then the HWRM shall enable FEC
+ * autonegotitation on this port if supported. When set to 0,
+ * then this flag shall be ignored. If FEC autonegotiation is
+ * not supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_ENABLE UINT32_C(0x100)
+ /*
+ * When set to 1, then the HWRM shall disable FEC
+ * autonegotiation on this port if supported. When set to 0,
+ * then this flag shall be ignored. If FEC autonegotiation is
+ * not supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_AUTONEG_DISABLE \
+ UINT32_C(0x200)
+ /*
+ * When set to 1, then the HWRM shall enable FEC CLAUSE 74 (Fire
+ * Code) on this port if supported. When set to 0, then this
+ * flag shall be ignored. If FEC CLAUSE 74 is not supported,
+ * then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_ENABLE \
+ UINT32_C(0x400)
+ /*
+ * When set to 1, then the HWRM shall disable FEC CLAUSE 74
+ * (Fire Code) on this port if supported. When set to 0, then
+ * this flag shall be ignored. If FEC CLAUSE 74 is not
+ * supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE74_DISABLE \
+ UINT32_C(0x800)
+ /*
+ * When set to 1, then the HWRM shall enable FEC CLAUSE 91 (Reed
+ * Solomon) on this port if supported. When set to 0, then this
+ * flag shall be ignored. If FEC CLAUSE 91 is not supported,
+ * then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_ENABLE \
+ UINT32_C(0x1000)
+ /*
+ * When set to 1, then the HWRM shall disable FEC CLAUSE 91
+ * (Reed Solomon) on this port if supported. When set to 0, then
+ * this flag shall be ignored. If FEC CLAUSE 91 is not
+ * supported, then the HWRM shall ignore this flag.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FEC_CLAUSE91_DISABLE \
+ UINT32_C(0x2000)
+ /*
+ * When this bit is set to '1', the link shall be forced to be
+ * taken down. # When this bit is set to '1", all other command
+ * input settings related to the link speed shall be ignored.
+ * Once the link state is forced down, it can be explicitly
+ * cleared from that state by setting this flag to '0'. # If
+ * this flag is set to '0', then the link shall be cleared from
+ * forced down state if the link is in forced down state. There
+ * may be conditions (e.g. out-of-band or sideband configuration
+ * changes for the link) outside the scope of the HWRM
+ * implementation that may clear forced down link state.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FLAGS_FORCE_LINK_DWN UINT32_C(0x4000)
+ uint32_t enables;
+ /* This bit must be '1' for the auto_mode field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_MODE UINT32_C(0x1)
+ /* This bit must be '1' for the auto_duplex field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_DUPLEX UINT32_C(0x2)
+ /* This bit must be '1' for the auto_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_PAUSE UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the auto_link_speed field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the auto_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_AUTO_LINK_SPEED_MASK \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the wirespeed field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_WIOUTPUTEED UINT32_C(0x20)
+ /* This bit must be '1' for the lpbk field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_LPBK UINT32_C(0x40)
+ /* This bit must be '1' for the preemphasis field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_PREEMPHASIS UINT32_C(0x80)
+ /* This bit must be '1' for the force_pause field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_FORCE_PAUSE UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the eee_link_speed_mask field to be
+ * configured.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_EEE_LINK_SPEED_MASK \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the tx_lpi_timer field to be configured. */
+ #define HWRM_PORT_PHY_CFG_INPUT_ENABLES_TX_LPI_TIMER UINT32_C(0x400)
+ uint16_t port_id;
+ /* Port ID of port that is to be configured. */
+ uint16_t force_link_speed;
+ /*
+ * This is the speed that will be used if the force bit is '1'.
+ * If unsupported speed is selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint8_t auto_mode;
+ /*
+ * This value is used to identify what autoneg mode is used when
+ * the link speed is not being forced.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_NONE UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ALL_SPEEDS UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_SPEED UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_MODE_SPEED_MASK UINT32_C(0x4)
+ uint8_t auto_duplex;
+ /*
+ * This is the duplex setting that will be used if the
+ * autoneg_mode is "one_speed" or "one_or_below".
+ */
+ /* Half Duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_HALF UINT32_C(0x0)
+ /* Full duplex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_FULL UINT32_C(0x1)
+ /* Both Half and Full dupex will be requested. */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_DUPLEX_BOTH UINT32_C(0x2)
+ uint8_t auto_pause;
+ /*
+ * This value is used to configure the pause that will be used
+ * for autonegotiation. Add text on the usage of auto_pause and
+ * force_pause.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has
+ * been requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When
+ * the auto_mode is not set to none and this flag is set to 1,
+ * then the auto_pause bits on this port are being advertised
+ * and autoneg pause results are being interpreted. # When the
+ * auto_mode is not set to none and this flag is set to 0, the
+ * pause is forced as indicated in force_pause, and also
+ * advertised as auto_pause bits, but the autoneg results are
+ * not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is
+ * set to 1, auto_pause bits should be ignored and should be set
+ * to 0.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
+ uint8_t unused_0;
+ uint16_t auto_link_speed;
+ /*
+ * This is the speed that will be used if the autoneg_mode is
+ * "one_speed" or "one_or_below". If an unsupported speed is
+ * selected, an error will be generated.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint16_t auto_link_speed_mask;
+ /*
+ * This is a mask of link speeds that will be used if
+ * autoneg_mode is "mask". If unsupported speed is enabled an
+ * error will be generated.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10GB UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_20GB UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint8_t wirespeed;
+ /* This value controls the wirespeed feature. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_OFF UINT32_C(0x0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_CFG_INPUT_WIOUTPUTEED_ON UINT32_C(0x1)
+ uint8_t lpbk;
+ /* This value controls the loopback setting for the PHY. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_LPBK_REMOTE UINT32_C(0x2)
+ uint8_t force_pause;
+ /*
+ * This value is used to configure the pause that will be used
+ * for force mode.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_FORCE_PAUSE_RX UINT32_C(0x2)
+ uint8_t unused_1;
+ uint32_t preemphasis;
+ /*
+ * This value controls the pre-emphasis to be used for the link.
+ * Driver should not set this value (use enable.preemphasis = 0)
+ * unless driver is sure of setting. Normally HWRM FW will
+ * determine proper pre-emphasis.
+ */
+ uint16_t eee_link_speed_mask;
+ /*
+ * Setting for link speed mask that is used to advertise speeds
+ * during autonegotiation when EEE is enabled. This field is
+ * valid only when EEE is enabled. The speeds specified in this
+ * field shall be a subset of speeds specified in
+ * auto_link_speed_mask. If EEE is enabled,then at least one
+ * speed shall be provided in this mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD1 UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_100MB UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD2 UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_1GB UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD3 UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_RSVD4 UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_CFG_INPUT_EEE_LINK_SPEED_MASK_10GB UINT32_C(0x40)
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t tx_lpi_timer;
+ uint32_t unused_4;
+ /*
+ * Reuested setting of TX LPI timer in microseconds. This field
+ * is valid only when EEE is enabled and TX LPI is enabled.
+ */
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_CFG_INPUT_TX_LPI_TIMER_SFT 0
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_phy_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_phy_qcfg */
+/* Description: This command queries the PHY configuration for the port. */
+/* Input (24 bytes) */
+struct hwrm_port_phy_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is to be queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (96 bytes) */
+struct hwrm_port_phy_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t link;
+ /* This value indicates the current link status. */
+ /* There is no link or cable detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_NO_LINK UINT32_C(0x0)
+ /* There is no link, but a cable has been detected. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SIGNAL UINT32_C(0x1)
+ /* There is a link. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_LINK UINT32_C(0x2)
+ uint8_t unused_0;
+ uint16_t link_speed;
+ /* This value indicates the current link speed of the connection. */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint8_t duplex_cfg;
+ /* This value is indicates the duplex of the current connection. */
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_HALF UINT32_C(0x0)
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_CFG_FULL UINT32_C(0x1)
+ uint8_t pause;
+ /*
+ * This value is used to indicate the current pause
+ * configuration. When autoneg is enabled, this value represents
+ * the autoneg results of pause configuration.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PAUSE_RX UINT32_C(0x2)
+ uint16_t support_speeds;
+ /*
+ * The supported speeds for the port. This is a bit mask. For
+ * each speed that is supported, the corrresponding bit will be
+ * set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MBHD UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100MB UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GBHD UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_1GB UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2GB UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_2_5GB UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10GB UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_20GB UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_25GB UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_40GB UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_50GB UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_100GB UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MBHD UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_SUPPORT_SPEEDS_10MB UINT32_C(0x2000)
+ uint16_t force_link_speed;
+ /*
+ * Current setting of forced link speed. When the link speed is
+ * not being forced, this value shall be set to 0.
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint8_t auto_mode;
+ /* Current setting of auto negotiation mode. */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_NONE UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ALL_SPEEDS UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_SPEED UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_ONE_OR_BELOW UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_MODE_SPEED_MASK UINT32_C(0x4)
+ uint8_t auto_pause;
+ /*
+ * Current setting of pause autonegotiation. Move autoneg_pause
+ * flag here.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages has
+ * been requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages has been
+ * requested. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_RX UINT32_C(0x2)
+ /*
+ * When set to 1, the advertisement of pause is enabled. # When
+ * the auto_mode is not set to none and this flag is set to 1,
+ * then the auto_pause bits on this port are being advertised
+ * and autoneg pause results are being interpreted. # When the
+ * auto_mode is not set to none and this flag is set to 0, the
+ * pause is forced as indicated in force_pause, and also
+ * advertised as auto_pause bits, but the autoneg results are
+ * not interpreted since the pause configuration is being
+ * forced. # When the auto_mode is set to none and this flag is
+ * set to 1, auto_pause bits should be ignored and should be set
+ * to 0.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_PAUSE_AUTONEG_PAUSE UINT32_C(0x4)
+ uint16_t auto_link_speed;
+ /*
+ * Current setting for auto_link_speed. This field is only valid
+ * when auto_mode is set to "one_speed" or "one_or_below".
+ */
+ /* 100Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100MB UINT32_C(0x1)
+ /* 1Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_1GB UINT32_C(0xa)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2GB UINT32_C(0x14)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_2_5GB UINT32_C(0x19)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10GB UINT32_C(0x64)
+ /* 20Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_20GB UINT32_C(0xc8)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_25GB UINT32_C(0xfa)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_40GB UINT32_C(0x190)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_50GB UINT32_C(0x1f4)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_100GB UINT32_C(0x3e8)
+ /* 10Mb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_10MB UINT32_C(0xffff)
+ uint16_t auto_link_speed_mask;
+ /*
+ * Current setting for auto_link_speed_mask that is used to
+ * advertise speeds during autonegotiation. This field is only
+ * valid when auto_mode is set to "mask". The speeds specified
+ * in this field shall be a subset of supported speeds on this
+ * port.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_1GB UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_AUTO_LINK_SPEED_MASK_10MB \
+ UINT32_C(0x2000)
+ uint8_t wirespeed;
+ /* Current setting for wirespeed. */
+ /* Wirespeed feature is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_OFF UINT32_C(0x0)
+ /* Wirespeed feature is enabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_WIOUTPUTEED_ON UINT32_C(0x1)
+ uint8_t lpbk;
+ /* Current setting for loopback. */
+ /* No loopback is selected. Normal operation. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_NONE UINT32_C(0x0)
+ /*
+ * The HW will be configured with local loopback
+ * such that host data is sent back to the host
+ * without modification.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_LOCAL UINT32_C(0x1)
+ /*
+ * The HW will be configured with remote
+ * loopback such that port logic will send
+ * packets back out the transmitter that are
+ * received.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LPBK_REMOTE UINT32_C(0x2)
+ uint8_t force_pause;
+ /*
+ * Current setting of forced pause. When the pause configuration
+ * is not being forced, then this value shall be set to 0.
+ */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_TX UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FORCE_PAUSE_RX UINT32_C(0x2)
+ uint8_t module_status;
+ /*
+ * This value indicates the current status of the optics module
+ * on this port.
+ */
+ /* Module is inserted and accepted */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NONE UINT32_C(0x0)
+ /* Module is rejected and transmit side Laser is disabled. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_DISABLETX UINT32_C(0x1)
+ /* Module mismatch warning. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_WARNINGMSG UINT32_C(0x2)
+ /* Module is rejected and powered down. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_PWRDOWN UINT32_C(0x3)
+ /* Module is not inserted. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTINSERTED \
+ UINT32_C(0x4)
+ /* Module status is not applicable. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MODULE_STATUS_NOTAPPLICABLE \
+ UINT32_C(0xff)
+ uint32_t preemphasis;
+ /* Current setting for preemphasis. */
+ uint8_t phy_maj;
+ /* This field represents the major version of the PHY. */
+ uint8_t phy_min;
+ /* This field represents the minor version of the PHY. */
+ uint8_t phy_bld;
+ /* This field represents the build version of the PHY. */
+ uint8_t phy_type;
+ /* This value represents a PHY type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_UNKNOWN UINT32_C(0x0)
+ /* BASE-CR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASECR UINT32_C(0x1)
+ /* BASE-KR4 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR4 UINT32_C(0x2)
+ /* BASE-LR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASELR UINT32_C(0x3)
+ /* BASE-SR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASESR UINT32_C(0x4)
+ /* BASE-KR2 (Deprecated) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR2 UINT32_C(0x5)
+ /* BASE-KX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKX UINT32_C(0x6)
+ /* BASE-KR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASEKR UINT32_C(0x7)
+ /* BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASET UINT32_C(0x8)
+ /* EEE capable BASE-T */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_BASETE UINT32_C(0x9)
+ /* SGMII connected external PHY */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_SGMIIEXTPHY UINT32_C(0xa)
+ /* 25G_BASECR_CA_L */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_L UINT32_C(0xb)
+ /* 25G_BASECR_CA_S */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_S UINT32_C(0xc)
+ /* 25G_BASECR_CA_N */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASECR_CA_N UINT32_C(0xd)
+ /* 25G_BASESR */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_25G_BASESR UINT32_C(0xe)
+ /* 100G_BASECR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASECR4 UINT32_C(0xf)
+ /* 100G_BASESR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR4 UINT32_C(0x10)
+ /* 100G_BASELR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASELR4 UINT32_C(0x11)
+ /* 100G_BASEER4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASEER4 UINT32_C(0x12)
+ /* 100G_BASESR10 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_100G_BASESR10 UINT32_C(0x13)
+ /* 40G_BASECR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASECR4 UINT32_C(0x14)
+ /* 40G_BASESR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASESR4 UINT32_C(0x15)
+ /* 40G_BASELR4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASELR4 UINT32_C(0x16)
+ /* 40G_BASEER4 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_BASEER4 UINT32_C(0x17)
+ /* 40G_ACTIVE_CABLE */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_40G_ACTIVE_CABLE \
+ UINT32_C(0x18)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASET UINT32_C(0x19)
+ /* 1G_baseSX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASESX UINT32_C(0x1a)
+ /* 1G_baseCX */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_TYPE_1G_BASECX UINT32_C(0x1b)
+ uint8_t media_type;
+ /* This value represents a media type. */
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_UNKNOWN UINT32_C(0x0)
+ /* Twisted Pair */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_TP UINT32_C(0x1)
+ /* Direct Attached Copper */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_DAC UINT32_C(0x2)
+ /* Fiber */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_MEDIA_TYPE_FIBRE UINT32_C(0x3)
+ uint8_t xcvr_pkg_type;
+ /* This value represents a transceiver type. */
+ /* PHY and MAC are in the same package */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_INTERNAL \
+ UINT32_C(0x1)
+ /* PHY and MAC are in different packages */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_PKG_TYPE_XCVR_EXTERNAL \
+ UINT32_C(0x2)
+ uint8_t eee_config_phy_addr;
+ /*
+ * This field represents flags related to EEE configuration.
+ * These EEE configuration flags are valid only when the
+ * auto_mode is not set to none (in other words autonegotiation
+ * is enabled).
+ */
+ /* This field represents PHY address. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_MASK UINT32_C(0x1f)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PHY_ADDR_SFT 0
+ /*
+ * When set to 1, Energy Efficient Ethernet (EEE) mode is
+ * enabled. Speeds for autoneg with EEE mode enabled are based
+ * on eee_link_speed_mask.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ENABLED UINT32_C(0x20)
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this
+ * flag shall be ignored. # If eee_enabled is set to 1 and this
+ * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
+ * is enabled and in use. # If eee_enabled is set to 1 and this
+ * flag is set to 0, then Energy Efficient Ethernet (EEE) mode
+ * is enabled but is currently not in use.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_ACTIVE UINT32_C(0x40)
+ /*
+ * This flag is valid only when eee_enabled is set to 1. # If
+ * eee_enabled is set to 0, then EEE mode is disabled and this
+ * flag shall be ignored. # If eee_enabled is set to 1 and this
+ * flag is set to 1, then Energy Efficient Ethernet (EEE) mode
+ * is enabled and TX LPI is enabled. # If eee_enabled is set to
+ * 1 and this flag is set to 0, then Energy Efficient Ethernet
+ * (EEE) mode is enabled but TX LPI is disabled.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_EEE_TX_LPI UINT32_C(0x80)
+ /*
+ * This field represents flags related to EEE configuration.
+ * These EEE configuration flags are valid only when the
+ * auto_mode is not set to none (in other words autonegotiation
+ * is enabled).
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_MASK UINT32_C(0xe0)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_EEE_CONFIG_SFT 5
+ uint8_t parallel_detect;
+ /* Reserved field, set to 0 */
+ /*
+ * When set to 1, the parallel detection is used to determine
+ * the speed of the link partner. Parallel detection is used
+ * when a autonegotiation capable device is connected to a link
+ * parter that is not capable of autonegotiation.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_PARALLEL_DETECT UINT32_C(0x1)
+ /* Reserved field, set to 0 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_MASK UINT32_C(0xfe)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_RESERVED_SFT 1
+ uint16_t link_partner_adv_speeds;
+ /*
+ * The advertised speeds for the port by the link partner. Each
+ * advertised speed will be set to '1'.
+ */
+ /* 100Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MBHD \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100MB \
+ UINT32_C(0x2)
+ /* 1Gb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GBHD \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_1GB \
+ UINT32_C(0x8)
+ /* 2Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2GB \
+ UINT32_C(0x10)
+ /* 2.5Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_2_5GB \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10GB \
+ UINT32_C(0x40)
+ /* 20Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_20GB \
+ UINT32_C(0x80)
+ /* 25Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_25GB \
+ UINT32_C(0x100)
+ /* 40Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_40GB \
+ UINT32_C(0x200)
+ /* 50Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_50GB \
+ UINT32_C(0x400)
+ /* 100Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_100GB \
+ UINT32_C(0x800)
+ /* 10Mb link speed (Half-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MBHD \
+ UINT32_C(0x1000)
+ /* 10Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_SPEEDS_10MB \
+ UINT32_C(0x2000)
+ uint8_t link_partner_adv_auto_mode;
+ /*
+ * The advertised autoneg for the port by the link partner. This
+ * field is deprecated and should be set to 0.
+ */
+ /*
+ * Disable autoneg or autoneg disabled. No
+ * speeds are selected.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_NONE \
+ UINT32_C(0x0)
+ /* Select all possible speeds for autoneg mode. */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ALL_SPEEDS \
+ UINT32_C(0x1)
+ /*
+ * Select only the auto_link_speed speed for
+ * autoneg mode. This mode has been DEPRECATED.
+ * An HWRM client should not use this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_SPEED \
+ UINT32_C(0x2)
+ /*
+ * Select the auto_link_speed or any speed below
+ * that speed for autoneg. This mode has been
+ * DEPRECATED. An HWRM client should not use
+ * this mode.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_ONE_OR_BELOW \
+ UINT32_C(0x3)
+ /*
+ * Select the speeds based on the corresponding
+ * link speed mask value that is provided.
+ */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_AUTO_MODE_SPEED_MASK \
+ UINT32_C(0x4)
+ uint8_t link_partner_adv_pause;
+ /* The advertised pause settings on the port by the link partner. */
+ /*
+ * When this bit is '1', Generation of tx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_TX \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', Reception of rx pause messages is
+ * supported. Disabled otherwise.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_PAUSE_RX \
+ UINT32_C(0x2)
+ uint16_t adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is used to advertise
+ * speeds during autonegotiation when EEE is enabled. This field
+ * is valid only when eee_enabled flags is set to 1. The speeds
+ * specified in this field shall be a subset of speeds specified
+ * in auto_link_speed_mask.
+ */
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint16_t link_partner_adv_eee_link_speed_mask;
+ /*
+ * Current setting for link speed mask that is advertised by the
+ * link partner when EEE is enabled. This field is valid only
+ * when eee_enabled flags is set to 1.
+ */
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD1 \
+ UINT32_C(0x1)
+ /* 100Mb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_100MB \
+ UINT32_C(0x2)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD2 \
+ UINT32_C(0x4)
+ /* 1Gb link speed (Full-duplex) */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_1GB \
+ UINT32_C(0x8)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD3 \
+ UINT32_C(0x10)
+ /* Reserved */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_RSVD4 \
+ UINT32_C(0x20)
+ /* 10Gb link speed */
+ #define \
+ HWRM_PORT_PHY_QCFG_OUTPUT_LINK_PARTNER_ADV_EEE_LINK_SPEED_MASK_10GB \
+ UINT32_C(0x40)
+ uint32_t xcvr_identifier_type_tx_lpi_timer;
+ /* This value represents transceiver identifier type. */
+ /*
+ * Current setting of TX LPI timer in microseconds. This field
+ * is valid only when_eee_enabled flag is set to 1 and
+ * tx_lpi_enabled is set to 1.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_MASK UINT32_C(0xffffff)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_TX_LPI_TIMER_SFT 0
+ /* This value represents transceiver identifier type. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_MASK \
+ UINT32_C(0xff000000)
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFT 24
+ /* Unknown */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_UNKNOWN \
+ (UINT32_C(0x0) << 24)
+ /* SFP/SFP+/SFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_SFP \
+ (UINT32_C(0x3) << 24)
+ /* QSFP */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP \
+ (UINT32_C(0xc) << 24)
+ /* QSFP+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFPPLUS \
+ (UINT32_C(0xd) << 24)
+ /* QSFP28 */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_XCVR_IDENTIFIER_TYPE_QSFP28 \
+ (UINT32_C(0x11) << 24)
+ uint16_t fec_cfg;
+ /*
+ * This value represents the current configuration of Forward
+ * Error Correction (FEC) on the port.
+ */
+ /*
+ * When set to 1, then FEC is not supported on this port. If
+ * this flag is set to 1, then all other FEC configuration flags
+ * shall be ignored. When set to 0, then FEC is supported as
+ * indicated by other configuration flags. If no cable is
+ * attached and the HWRM does not yet know the FEC capability,
+ * then the HWRM shall set this flag to 1 when reporting FEC
+ * capability.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_NONE_SUPPORTED \
+ UINT32_C(0x1)
+ /*
+ * When set to 1, then FEC autonegotiation is supported on this
+ * port. When set to 0, then FEC autonegotiation is not
+ * supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * When set to 1, then FEC autonegotiation is enabled on this
+ * port. When set to 0, then FEC autonegotiation is disabled if
+ * supported. This flag should be ignored if FEC autonegotiation
+ * is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_AUTONEG_ENABLED \
+ UINT32_C(0x4)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is supported on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * When set to 1, then FEC CLAUSE 74 (Fire Code) is enabled on
+ * this port. When set to 0, then FEC CLAUSE 74 (Fire Code) is
+ * disabled if supported. This flag should be ignored if FEC
+ * CLAUSE 74 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE74_ENABLED \
+ UINT32_C(0x10)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is supported
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_SUPPORTED \
+ UINT32_C(0x20)
+ /*
+ * When set to 1, then FEC CLAUSE 91 (Reed Solomon) is enabled
+ * on this port. When set to 0, then FEC CLAUSE 91 (Reed
+ * Solomon) is disabled if supported. This flag should be
+ * ignored if FEC CLAUSE 91 is not supported on this port.
+ */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_FEC_CFG_FEC_CLAUSE91_ENABLED \
+ UINT32_C(0x40)
+ uint8_t duplex_state;
+ /*
+ * This value is indicates the duplex of the current connection
+ * state.
+ */
+ /* Half Duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_HALF UINT32_C(0x0)
+ /* Full duplex connection. */
+ #define HWRM_PORT_PHY_QCFG_OUTPUT_DUPLEX_STATE_FULL UINT32_C(0x1)
+ uint8_t unused_1;
+ char phy_vendor_name[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string representing PHY
+ * vendor. If the string is set to null, then the vendor name is
+ * not available.
+ */
+ char phy_vendor_partnumber[16];
+ /*
+ * Up to 16 bytes of null padded ASCII string that identifies
+ * vendor specific part number of the PHY. If the string is set
+ * to null, then the vendor specific part number is not
+ * available.
+ */
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_qstats */
+/* Description: This function returns per port Ethernet statistics. */
+/* Input (40 bytes) */
+struct hwrm_port_qstats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2[3];
+ uint8_t unused_3;
+ uint64_t tx_stat_host_addr;
+ /* This is the host address where Tx port statistics will be stored */
+ uint64_t rx_stat_host_addr;
+ /* This is the host address where Rx port statistics will be stored */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_qstats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t tx_stat_size;
+ /* The size of TX port statistics block in bytes. */
+ uint16_t rx_stat_size;
+ /* The size of RX port statistics block in bytes. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_clr_stats */
+/*
+ * Description: This function clears per port statistics. The HWRM shall not
+ * allow a VF driver to clear port statistics. The HWRM shall not allow a PF
+ * driver to clear port statistics in a partitioning mode. The HWRM may allow a
+ * PF driver to clear port statistics in the non-partitioning mode.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_clr_stats_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port that is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_clr_stats_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_led_cfg */
+/*
+ * Description: This function is used to configure LEDs on a given port. Each
+ * port has individual set of LEDs associated with it. These LEDs are used for
+ * speed/link configuration as well as activity indicator configuration. Up to
+ * three LEDs can be configured, one for activity and two for speeds.
+ */
+/* Input (64 bytes) */
+struct hwrm_port_led_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the led0_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_ID UINT32_C(0x1)
+ /* This bit must be '1' for the led0_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_STATE UINT32_C(0x2)
+ /* This bit must be '1' for the led0_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_COLOR UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the led0_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_ON UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the led0_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_BLINK_OFF UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the led0_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED0_GROUP_ID UINT32_C(0x20)
+ /* This bit must be '1' for the led1_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_ID UINT32_C(0x40)
+ /* This bit must be '1' for the led1_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_STATE UINT32_C(0x80)
+ /* This bit must be '1' for the led1_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_COLOR UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the led1_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_ON UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the led1_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_BLINK_OFF UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the led1_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED1_GROUP_ID UINT32_C(0x800)
+ /* This bit must be '1' for the led2_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_ID UINT32_C(0x1000)
+ /* This bit must be '1' for the led2_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_STATE UINT32_C(0x2000)
+ /* This bit must be '1' for the led2_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_COLOR UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the led2_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_ON UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the led2_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_BLINK_OFF UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the led2_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED2_GROUP_ID UINT32_C(0x20000)
+ /* This bit must be '1' for the led3_id field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_ID UINT32_C(0x40000)
+ /* This bit must be '1' for the led3_state field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_STATE UINT32_C(0x80000)
+ /* This bit must be '1' for the led3_color field to be configured. */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_COLOR UINT32_C(0x100000)
+ /*
+ * This bit must be '1' for the led3_blink_on field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_ON UINT32_C(0x200000)
+ /*
+ * This bit must be '1' for the led3_blink_off field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_BLINK_OFF \
+ UINT32_C(0x400000)
+ /*
+ * This bit must be '1' for the led3_group_id field to be
+ * configured.
+ */
+ #define HWRM_PORT_LED_CFG_INPUT_ENABLES_LED3_GROUP_ID UINT32_C(0x800000)
+ uint16_t port_id;
+ /* Port ID of port whose LEDs are configured. */
+ uint8_t num_leds;
+ /*
+ * The number of LEDs that are being configured. Up to 4 LEDs
+ * can be configured with this command.
+ */
+ uint8_t rsvd;
+ /* Reserved field. */
+ uint8_t led0_id;
+ /* An identifier for the LED #0. */
+ uint8_t led0_state;
+ /* The requested state of the LED #0. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led0_color;
+ /* The requested color of LED #0. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_0;
+ uint16_t led0_blink_on;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led0_blink_off;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led0_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #0 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd0;
+ /* Reserved field. */
+ uint8_t led1_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_state;
+ /* The requested state of the LED #1. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led1_color;
+ /* The requested color of LED #1. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_1;
+ uint16_t led1_blink_on;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led1_blink_off;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led1_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs to.
+ * If set to 0, then the LED #1 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #1 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd1;
+ /* Reserved field. */
+ uint8_t led2_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_state;
+ /* The requested state of the LED #2. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led2_color;
+ /* The requested color of LED #2. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_2;
+ uint16_t led2_blink_on;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led2_blink_off;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led2_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #2 belongs to.
+ * If set to 0, then the LED #2 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #2 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd2;
+ /* Reserved field. */
+ uint8_t led3_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_state;
+ /* The requested state of the LED #3. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led3_color;
+ /* The requested color of LED #3. */
+ /* Default */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_CFG_INPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_3;
+ uint16_t led3_blink_on;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led3_blink_off;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led3_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs to.
+ * If set to 0, then the LED #3 shall not be grouped and shall
+ * be treated as an individual resource. For all other non-zero
+ * values of this field, LED #3 shall be grouped together with
+ * the LEDs with the same group ID value.
+ */
+ uint8_t rsvd3;
+ /* Reserved field. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_port_led_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_led_qcfg */
+/*
+ * Description: This function is used to query configuration of LEDs on a given
+ * port. Each port has individual set of LEDs associated with it. These LEDs are
+ * used for speed/link configuration as well as activity indicator
+ * configuration. Up to three LEDs can be configured, one for activity and two
+ * for speeds.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_led_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port whose LED configuration is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (56 bytes) */
+struct hwrm_port_led_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t num_leds;
+ /*
+ * The number of LEDs that are configured on this port. Up to 4
+ * LEDs can be returned in the response.
+ */
+ uint8_t led0_id;
+ /* An identifier for the LED #0. */
+ uint8_t led0_type;
+ /* The type of LED #0. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led0_state;
+ /* The current state of the LED #0. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led0_color;
+ /* The color of LED #0. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED0_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_0;
+ uint16_t led0_blink_on;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led0_blink_off;
+ /*
+ * If the LED #0 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led0_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 is not grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t led1_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_type;
+ /* The type of LED #1. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led1_state;
+ /* The current state of the LED #1. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led1_color;
+ /* The color of LED #1. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED1_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_1;
+ uint16_t led1_blink_on;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led1_blink_off;
+ /*
+ * If the LED #1 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led1_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs to.
+ * If set to 0, then the LED #1 is not grouped. For all other
+ * non-zero values of this field, LED #1 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t led2_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_type;
+ /* The type of LED #2. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led2_state;
+ /* The current state of the LED #2. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led2_color;
+ /* The color of LED #2. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED2_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_2;
+ uint16_t led2_blink_on;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led2_blink_off;
+ /*
+ * If the LED #2 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led2_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #2 belongs to.
+ * If set to 0, then the LED #2 is not grouped. For all other
+ * non-zero values of this field, LED #2 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t led3_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_type;
+ /* The type of LED #3. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led3_state;
+ /* The current state of the LED #3. */
+ /* Default state of the LED */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_DEFAULT UINT32_C(0x0)
+ /* Off */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_OFF UINT32_C(0x1)
+ /* On */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_ON UINT32_C(0x2)
+ /* Blink */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINK UINT32_C(0x3)
+ /* Blink Alternately */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_STATE_BLINKALT UINT32_C(0x4)
+ uint8_t led3_color;
+ /* The color of LED #3. */
+ /* Default */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_DEFAULT UINT32_C(0x0)
+ /* Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_AMBER UINT32_C(0x1)
+ /* Green */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREEN UINT32_C(0x2)
+ /* Green or Amber */
+ #define HWRM_PORT_LED_QCFG_OUTPUT_LED3_COLOR_GREENAMBER UINT32_C(0x3)
+ uint8_t unused_3;
+ uint16_t led3_blink_on;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED on
+ * between cycles.
+ */
+ uint16_t led3_blink_off;
+ /*
+ * If the LED #3 state is "blink" or "blinkalt", then this field
+ * represents the requested time in milliseconds to keep LED off
+ * between cycles.
+ */
+ uint8_t led3_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs to.
+ * If set to 0, then the LED #3 is not grouped. For all other
+ * non-zero values of this field, LED #3 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_4;
+ uint16_t unused_5;
+ uint8_t unused_6;
+ uint8_t unused_7;
+ uint8_t unused_8;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_port_led_qcaps */
+/*
+ * Description: This function is used to query capabilities of LEDs on a given
+ * port. Each port has individual set of LEDs associated with it. These LEDs are
+ * used for speed/link configuration as well as activity indicator
+ * configuration.
+ */
+/* Input (24 bytes) */
+struct hwrm_port_led_qcaps_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t port_id;
+ /* Port ID of port whose LED configuration is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (48 bytes) */
+struct hwrm_port_led_qcaps_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t num_leds;
+ /*
+ * The number of LEDs that are configured on this port. Up to 4
+ * LEDs can be returned in the response.
+ */
+ uint8_t unused_0[3];
+ /* Reserved for future use. */
+ uint8_t led0_id;
+ /* An identifier for the LED #0. */
+ uint8_t led0_type;
+ /* The type of LED #0. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led0_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_1;
+ uint16_t led0_state_caps;
+ /* The states supported by LED #0. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ENABLED UINT32_C(0x1)
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_OFF_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_ON_SUPPORTED \
+ UINT32_C(0x4)
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ UINT32_C(0x10)
+ uint16_t led0_color_caps;
+ /* The colors supported by LED #0. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_RSVD UINT32_C(0x1)
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_AMBER_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED0_COLOR_CAPS_GREEN_SUPPORTED \
+ UINT32_C(0x4)
+ uint8_t led1_id;
+ /* An identifier for the LED #1. */
+ uint8_t led1_type;
+ /* The type of LED #1. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led1_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #1 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_2;
+ uint16_t led1_state_caps;
+ /* The states supported by LED #1. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ENABLED UINT32_C(0x1)
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_OFF_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_ON_SUPPORTED \
+ UINT32_C(0x4)
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ UINT32_C(0x10)
+ uint16_t led1_color_caps;
+ /* The colors supported by LED #1. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_RSVD UINT32_C(0x1)
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_AMBER_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED1_COLOR_CAPS_GREEN_SUPPORTED \
+ UINT32_C(0x4)
+ uint8_t led2_id;
+ /* An identifier for the LED #2. */
+ uint8_t led2_type;
+ /* The type of LED #2. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led2_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #0 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_3;
+ uint16_t led2_state_caps;
+ /* The states supported by LED #2. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ENABLED UINT32_C(0x1)
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_OFF_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_ON_SUPPORTED \
+ UINT32_C(0x4)
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ UINT32_C(0x10)
+ uint16_t led2_color_caps;
+ /* The colors supported by LED #2. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_RSVD UINT32_C(0x1)
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_AMBER_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED2_COLOR_CAPS_GREEN_SUPPORTED \
+ UINT32_C(0x4)
+ uint8_t led3_id;
+ /* An identifier for the LED #3. */
+ uint8_t led3_type;
+ /* The type of LED #3. */
+ /* Speed LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_SPEED UINT32_C(0x0)
+ /* Activity LED */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_ACTIVITY UINT32_C(0x1)
+ /* Invalid */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_TYPE_INVALID UINT32_C(0xff)
+ uint8_t led3_group_id;
+ /*
+ * An identifier for the group of LEDs that LED #3 belongs to.
+ * If set to 0, then the LED #0 cannot be grouped. For all other
+ * non-zero values of this field, LED #0 is grouped together
+ * with the LEDs with the same group ID value.
+ */
+ uint8_t unused_4;
+ uint16_t led3_state_caps;
+ /* The states supported by LED #3. */
+ /*
+ * If set to 1, this LED is enabled. If set to 0, this LED is
+ * disabled.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ENABLED UINT32_C(0x1)
+ /*
+ * If set to 1, off state is supported on this LED. If set to 0,
+ * off state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_OFF_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, on state is supported on this LED. If set to 0,
+ * on state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_ON_SUPPORTED \
+ UINT32_C(0x4)
+ /*
+ * If set to 1, blink state is supported on this LED. If set to
+ * 0, blink state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_SUPPORTED \
+ UINT32_C(0x8)
+ /*
+ * If set to 1, blink_alt state is supported on this LED. If set
+ * to 0, blink_alt state is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_STATE_CAPS_BLINK_ALT_SUPPORTED \
+ UINT32_C(0x10)
+ uint16_t led3_color_caps;
+ /* The colors supported by LED #3. */
+ /* reserved */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_RSVD UINT32_C(0x1)
+ /*
+ * If set to 1, Amber color is supported on this LED. If set to
+ * 0, Amber color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_AMBER_SUPPORTED \
+ UINT32_C(0x2)
+ /*
+ * If set to 1, Green color is supported on this LED. If set to
+ * 0, Green color is not supported on this LED.
+ */
+ #define HWRM_PORT_LED_QCAPS_OUTPUT_LED3_COLOR_CAPS_GREEN_SUPPORTED \
+ UINT32_C(0x4)
+ uint8_t unused_5;
+ uint8_t unused_6;
+ uint8_t unused_7;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_queue_qportcfg */
+/*
+ * Description: This function is called by a driver to query queue configuration
+ * of a port. # The HWRM shall at least advertise one queue with lossy service
+ * profile. # The driver shall use this command to query queue ids before
+ * configuring or using any queues. # If a service profile is not set for a
+ * queue, then the driver shall not use that queue without configuring a service
+ * profile for it. # If the driver is not allowed to configure service profiles,
+ * then the driver shall only use queues for which service profiles are pre-
+ * configured.
+ */
+/* Input (24 bytes) */
+struct hwrm_queue_qportcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_QUEUE_QPORTCFG_INPUT_FLAGS_PATH_LAST \
+ QUEUE_QPORTCFG_INPUT_FLAGS_PATH_RX
+ uint16_t port_id;
+ /*
+ * Port ID of port for which the queue configuration is being
+ * queried. This field is only required when sent by IPC.
+ */
+ uint16_t unused_0;
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_queue_qportcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint8_t max_configurable_queues;
+ /*
+ * The maximum number of queues that can be configured on this
+ * port. Valid values range from 1 through 8.
+ */
+ uint8_t max_configurable_lossless_queues;
+ /*
+ * The maximum number of lossless queues that can be configured
+ * on this port. Valid values range from 0 through 8.
+ */
+ uint8_t queue_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_cfg command. Each bit represents a specific queue
+ * where bit 0 represents queue 0 and bit 7 represents queue 7.
+ * # A value of 0 indicates that the queue is not configurable
+ * by the hwrm_queue_cfg command. # A value of 1 indicates that
+ * the queue is configurable. # A hwrm_queue_cfg command shall
+ * return error when trying to configure a queue not
+ * configurable.
+ */
+ uint8_t queue_cfg_info;
+ /* Information about queue configuration. */
+ /*
+ * If this flag is set to '1', then the queues are configured
+ * asymmetrically on TX and RX sides. If this flag is set to
+ * '0', then the queues are configured symmetrically on TX and
+ * RX sides. For symmetric configuration, the queue
+ * configuration including queue ids and service profiles on the
+ * TX side is the same as the corresponding queue configuration
+ * on the RX side.
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG UINT32_C(0x1)
+ uint8_t queue_pfcenable_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pfcenable_cfg command. Each bit represents a
+ * specific priority where bit 0 represents priority 0 and bit 7
+ * represents priority 7. # A value of 0 indicates that the
+ * priority is not configurable by the hwrm_queue_pfcenable_cfg
+ * command. # A value of 1 indicates that the priority is
+ * configurable. # A hwrm_queue_pfcenable_cfg command shall
+ * return error when trying to configure a priority that is not
+ * configurable.
+ */
+ uint8_t queue_pri2cos_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pri2cos_cfg command. Each bit represents a
+ * specific queue where bit 0 represents queue 0 and bit 7
+ * represents queue 7. # A value of 0 indicates that the queue
+ * is not configurable by the hwrm_queue_pri2cos_cfg command. #
+ * A value of 1 indicates that the queue is configurable. # A
+ * hwrm_queue_pri2cos_cfg command shall return error when trying
+ * to configure a queue that is not configurable.
+ */
+ uint8_t queue_cos2bw_cfg_allowed;
+ /*
+ * Bitmask indicating which queues can be configured by the
+ * hwrm_queue_pri2cos_cfg command. Each bit represents a
+ * specific queue where bit 0 represents queue 0 and bit 7
+ * represents queue 7. # A value of 0 indicates that the queue
+ * is not configurable by the hwrm_queue_pri2cos_cfg command. #
+ * A value of 1 indicates that the queue is configurable. # A
+ * hwrm_queue_pri2cos_cfg command shall return error when trying
+ * to configure a queue not configurable.
+ */
+ uint8_t queue_id0;
+ /*
+ * ID of CoS Queue 0. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id0_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID0_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id1;
+ /*
+ * ID of CoS Queue 1. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id1_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID1_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id2;
+ /*
+ * ID of CoS Queue 2. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id2_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID2_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id3;
+ /*
+ * ID of CoS Queue 3. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id3_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID3_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id4;
+ /*
+ * ID of CoS Queue 4. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id4_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID4_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id5;
+ /*
+ * ID of CoS Queue 5. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id5_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID5_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id6;
+ /*
+ * ID of CoS Queue 6. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id6_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID6_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t queue_id7;
+ /*
+ * ID of CoS Queue 7. FF - Invalid id # This ID can be used on
+ * any subsequent call to an hwrm command that takes a queue id.
+ * # IDs must always be queried by this command before any use
+ * by the driver or software. # Any driver or software should
+ * not make any assumptions about queue IDs. # A value of 0xff
+ * indicates that the queue is not available. # Available queues
+ * may not be in sequential order.
+ */
+ uint8_t queue_id7_service_profile;
+ /* This value is applicable to CoS queues only. */
+ /* Lossy (best-effort) */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSY \
+ UINT32_C(0x0)
+ /* Lossless */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_LOSSLESS \
+ UINT32_C(0x1)
+ /*
+ * Set to 0xFF... (All Fs) if there is no
+ * service profile specified
+ */
+ #define HWRM_QUEUE_QPORTCFG_OUTPUT_QUEUE_ID7_SERVICE_PROFILE_UNKNOWN \
+ UINT32_C(0xff)
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_alloc */
+/*
+ * Description: This VNIC is a resource in the RX side of the chip that is used
+ * to represent a virtual host "interface". # At the time of VNIC allocation or
+ * configuration, the function can specify whether it wants the requested VNIC
+ * to be the default VNIC for the function or not. # If a function requests
+ * allocation of a VNIC for the first time and a VNIC is successfully allocated
+ * by the HWRM, then the HWRM shall make the allocated VNIC as the default VNIC
+ * for that function. # The default VNIC shall be used for the default action
+ * for a partition or function. # For each VNIC allocated on a function, a
+ * mapping on the RX side to map the allocated VNIC to source virtual interface
+ * shall be performed by the HWRM. This should be hidden to the function driver
+ * requesting the VNIC allocation. This enables broadcast/multicast replication
+ * with source knockout. # If multicast replication with source knockout is
+ * enabled, then the internal VNIC to SVIF mapping data structures shall be
+ * programmed at the time of VNIC allocation.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', this VNIC is requested to be the
+ * default VNIC for this function.
+ */
+ #define HWRM_VNIC_ALLOC_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_free */
+/*
+ * Description: Free a VNIC resource. Idle any resources associated with the
+ * VNIC as well as the VNIC. Reset and release all resources associated with the
+ * VNIC.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_cfg */
+/* Description: Configure the RX VNIC structure. */
+/* Input (40 bytes) */
+struct hwrm_vnic_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is requested to be the default
+ * VNIC for the function.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is being configured to strip
+ * VLAN in the RX path. If set to '0', then VLAN stripping is
+ * disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is being configured to buffer
+ * receive packets in the hardware until the host posts new
+ * receive buffers. If set to '0', then bd_stall is being
+ * configured to be disabled on this VNIC.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is being configured to receive
+ * both RoCE and non-RoCE traffic. If set to '0', then this VNIC
+ * is not configured to be operating in dual VNIC mode.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is requested to be
+ * configured to receive only RoCE traffic. If this flag is set
+ * to '0', then this flag shall be ignored by the HWRM. If
+ * roce_dual_vnic_mode flag is set to '1', then the HWRM client
+ * shall not set this flag to '1'.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where exact match is
+ * used to direct packets to a VNIC with one destination ring
+ * group only, there is no need to configure RSS indirection
+ * table for that VNIC as only one destination ring group is
+ * used. This flag is used to enable a mode where RSS is enabled
+ * in the VNIC using a RSS context for computing RSS hash but
+ * the RSS indirection table is not configured using
+ * hwrm_vnic_rss_cfg. If this mode is enabled, then the driver
+ * should not program RSS indirection table for the RSS context
+ * that is used for computing RSS hash only.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_RSS_DFLT_CR_MODE UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is being configured to receive
+ * both RoCE and non-RoCE traffic, but forward only the RoCE
+ * traffic further. Also, RoCE traffic can be mirrored to L2
+ * driver.
+ */
+ #define HWRM_VNIC_CFG_INPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE \
+ UINT32_C(0x40)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the dflt_ring_grp field to be
+ * configured.
+ */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_DFLT_RING_GRP UINT32_C(0x1)
+ /* This bit must be '1' for the rss_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_RSS_RULE UINT32_C(0x2)
+ /* This bit must be '1' for the cos_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_COS_RULE UINT32_C(0x4)
+ /* This bit must be '1' for the lb_rule field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_LB_RULE UINT32_C(0x8)
+ /* This bit must be '1' for the mru field to be configured. */
+ #define HWRM_VNIC_CFG_INPUT_ENABLES_MRU UINT32_C(0x10)
+ uint16_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t dflt_ring_grp;
+ /*
+ * Default Completion ring for the VNIC. This ring will be
+ * chosen if packet does not match any RSS rules and if there is
+ * no COS rule.
+ */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All
+ * Fs) if there is no LB rule.
+ */
+ uint16_t mru;
+ /*
+ * The maximum receive unit of the vnic. Each vnic is associated
+ * with a function. The vnic mru value overwrites the mru
+ * setting of the associated function. The HWRM shall make sure
+ * that vnic mru does not exceed the mru of the port the
+ * function is associated with.
+ */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_qcfg */
+/*
+ * Description: Query the RX VNIC structure. This function can be used by a PF
+ * driver to query its own VNIC resource or VNIC resource of its child VF. This
+ * function can also be used by a VF driver to query its own VNIC resource.
+ */
+/* Input (32 bytes) */
+struct hwrm_vnic_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the vf_id_valid field to be configured. */
+ #define HWRM_VNIC_QCFG_INPUT_ENABLES_VF_ID_VALID UINT32_C(0x1)
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t vf_id;
+ /* ID of Virtual Function whose VNIC resource is being queried. */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (32 bytes) */
+struct hwrm_vnic_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t dflt_ring_grp;
+ /* Default Completion ring for the VNIC. */
+ uint16_t rss_rule;
+ /*
+ * RSS ID for RSS rule/table structure. 0xFF... (All Fs) if
+ * there is no RSS rule.
+ */
+ uint16_t cos_rule;
+ /*
+ * RSS ID for COS rule/table structure. 0xFF... (All Fs) if
+ * there is no COS rule.
+ */
+ uint16_t lb_rule;
+ /*
+ * RSS ID for load balancing rule/table structure. 0xFF... (All
+ * Fs) if there is no LB rule.
+ */
+ uint16_t mru;
+ /* The maximum receive unit of the vnic. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is the default VNIC for the
+ * function.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_DEFAULT UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is configured to strip VLAN in
+ * the RX path. If set to '0', then VLAN stripping is disabled
+ * on this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_VLAN_STRIP_MODE UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is configured to buffer
+ * receive packets in the hardware until the host posts new
+ * receive buffers. If set to '0', then bd_stall is disabled on
+ * this VNIC.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_BD_STALL_MODE UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is configured to receive both
+ * RoCE and non-RoCE traffic. If set to '0', then this VNIC is
+ * not configured to operate in dual VNIC mode.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_DUAL_VNIC_MODE UINT32_C(0x8)
+ /*
+ * When this flag is set to '1', the VNIC is configured to
+ * receive only RoCE traffic. When this flag is set to '0', the
+ * VNIC is not configured to receive only RoCE traffic. If
+ * roce_dual_vnic_mode flag and this flag both are set to '1',
+ * then it is an invalid configuration of the VNIC. The HWRM
+ * should not allow that type of mis-configuration by HWRM
+ * clients.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_ONLY_VNIC_MODE UINT32_C(0x10)
+ /*
+ * When a VNIC uses one destination ring group for certain
+ * application (e.g. Receive Flow Steering) where exact match is
+ * used to direct packets to a VNIC with one destination ring
+ * group only, there is no need to configure RSS indirection
+ * table for that VNIC as only one destination ring group is
+ * used. When this bit is set to '1', then the VNIC is enabled
+ * in a mode where RSS is enabled in the VNIC using a RSS
+ * context for computing RSS hash but the RSS indirection table
+ * is not configured.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_RSS_DFLT_CR_MODE UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is configured to receive both
+ * RoCE and non-RoCE traffic, but forward only RoCE traffic
+ * further. Also RoCE traffic can be mirrored to L2 driver.
+ */
+ #define HWRM_VNIC_QCFG_OUTPUT_FLAGS_ROCE_MIRRORING_CAPABLE_VNIC_MODE \
+ UINT32_C(0x40)
+ uint32_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+
+/* hwrm_vnic_tpa_cfg */
+/* Description: This function is used to enable/configure TPA on the VNIC. */
+/* Input (40 bytes) */
+struct hwrm_vnic_tpa_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) of non-tunneled TCP
+ * packets.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_TPA UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) of tunneled TCP packets.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_ENCAP_TPA UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) according to Windows
+ * Receive Segment Coalescing (RSC) rules.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_RSC_WND_UPDATE UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) according to Linux
+ * Generic Receive Offload (GRO) rules.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) for TCP packets with IP
+ * ECN set to non-zero.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_ECN UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC shall be configured to perform
+ * transparent packet aggregation (TPA) for GRE tunneled TCP
+ * packets only if all packets have the same GRE sequence.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_AGG_WITH_SAME_GRE_SEQ \
+ UINT32_C(0x20)
+ /*
+ * When this bit is '1' and the GRO mode is enabled, the VNIC
+ * shall be configured to perform transparent packet aggregation
+ * (TPA) for TCP/IPv4 packets with consecutively increasing
+ * IPIDs. In other words, the last packet that is being
+ * aggregated to an already existing aggregation context shall
+ * have IPID 1 more than the IPID of the last packet that was
+ * aggregated in that aggregation context.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_IPID_CHECK UINT32_C(0x40)
+ /*
+ * When this bit is '1' and the GRO mode is enabled, the VNIC
+ * shall be configured to perform transparent packet aggregation
+ * (TPA) for TCP packets with the same TTL (IPv4) or Hop limit
+ * (IPv6) value.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_FLAGS_GRO_TTL_CHECK UINT32_C(0x80)
+ uint32_t enables;
+ /* This bit must be '1' for the max_agg_segs field to be configured. */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_SEGS UINT32_C(0x1)
+ /* This bit must be '1' for the max_aggs field to be configured. */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGGS UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the max_agg_timer field to be
+ * configured.
+ */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MAX_AGG_TIMER UINT32_C(0x4)
+ /* This bit must be '1' for the min_agg_len field to be configured. */
+ #define HWRM_VNIC_TPA_CFG_INPUT_ENABLES_MIN_AGG_LEN UINT32_C(0x8)
+ uint16_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t max_agg_segs;
+ /*
+ * This is the maximum number of TCP segments that can be
+ * aggregated (unit is Log2). Max value is 31.
+ */
+ /* 1 segment */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_1 UINT32_C(0x0)
+ /* 2 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_2 UINT32_C(0x1)
+ /* 4 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_4 UINT32_C(0x2)
+ /* 8 segments */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_8 UINT32_C(0x3)
+ /* Any segment size larger than this is not valid */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGG_SEGS_MAX UINT32_C(0x1f)
+ uint16_t max_aggs;
+ /*
+ * This is the maximum number of aggregations this VNIC is
+ * allowed (unit is Log2). Max value is 7
+ */
+ /* 1 aggregation */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_1 UINT32_C(0x0)
+ /* 2 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_2 UINT32_C(0x1)
+ /* 4 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_4 UINT32_C(0x2)
+ /* 8 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_8 UINT32_C(0x3)
+ /* 16 aggregations */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_16 UINT32_C(0x4)
+ /* Any aggregation size larger than this is not valid */
+ #define HWRM_VNIC_TPA_CFG_INPUT_MAX_AGGS_MAX UINT32_C(0x7)
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t max_agg_timer;
+ /*
+ * This is the maximum amount of time allowed for an aggregation
+ * context to complete after it was initiated.
+ */
+ uint32_t min_agg_len;
+ /*
+ * This is the minimum amount of payload length required to
+ * start an aggregation context.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_tpa_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cfg */
+/* Description: This function is used to enable RSS configuration. */
+/* Input (48 bytes) */
+struct hwrm_vnic_rss_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t hash_type;
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV4 UINT32_C(0x1)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of TCP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV4 UINT32_C(0x2)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv4 addresses and source/destination
+ * ports of UDP/IPv4 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source and destination IPv4 addresses of IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of TCP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_TCP_IPV6 UINT32_C(0x10)
+ /*
+ * When this bit is '1', the RSS hash shall be computed over
+ * source/destination IPv6 addresses and source/destination
+ * ports of UDP/IPv6 packets.
+ */
+ #define HWRM_VNIC_RSS_CFG_INPUT_HASH_TYPE_UDP_IPV6 UINT32_C(0x20)
+ uint32_t unused_0;
+ uint64_t ring_grp_tbl_addr;
+ /* This is the address for rss ring group table */
+ uint64_t hash_key_tbl_addr;
+ /* This is the address for rss hash key table */
+ uint16_t rss_ctx_idx;
+ /* Index to the rss indirection table. */
+ uint16_t unused_1[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_plcmodes_cfg */
+/*
+ * Description: This function can be used to set placement mode configuration of
+ * the VNIC.
+ */
+/* Input (40 bytes) */
+struct hwrm_vnic_plcmodes_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC shall be configured to use regular
+ * placement algorithm. By default, the regular placement algorithm
+ * shall be enabled on the VNIC.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_REGULAR_PLACEMENT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC shall be configured use the jumbo
+ * placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_JUMBO_PLACEMENT \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for IPv4 packets according to the following rules: # If
+ * the packet is identified as TCP/IPv4, then the packet is split at the
+ * beginning of the TCP payload. # If the packet is identified as
+ * UDP/IPv4, then the packet is split at the beginning of UDP payload. #
+ * If the packet is identified as non-TCP and non-UDP IPv4 packet, then
+ * the packet is split at the beginning of the upper layer protocol
+ * header carried in the IPv4 packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for IPv6 packets according to the following rules: # If
+ * the packet is identified as TCP/IPv6, then the packet is split at the
+ * beginning of the TCP payload. # If the packet is identified as
+ * UDP/IPv6, then the packet is split at the beginning of UDP payload. #
+ * If the packet is identified as non-TCP and non-UDP IPv6 packet, then
+ * the packet is split at the beginning of the upper layer protocol
+ * header carried in the IPv6 packet.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for FCoE packets at the beginning of FC payload.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_FCOE UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC shall be configured to enable Header-
+ * Data split for RoCE packets at the beginning of RoCE payload (after
+ * BTH/GRH headers).
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_FLAGS_HDS_ROCE UINT32_C(0x20)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the jumbo_thresh_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_JUMBO_THRESH_VALID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the hds_offset_valid field to be configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_OFFSET_VALID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the hds_threshold_valid field to be
+ * configured.
+ */
+ #define HWRM_VNIC_PLCMODES_CFG_INPUT_ENABLES_HDS_THRESHOLD_VALID \
+ UINT32_C(0x4)
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint16_t jumbo_thresh;
+ /*
+ * When jumbo placement algorithm is enabled, this value is used to
+ * determine the threshold for jumbo placement. Packets with length
+ * larger than this value will be placed according to the jumbo
+ * placement algorithm.
+ */
+ uint16_t hds_offset;
+ /*
+ * This value is used to determine the offset into packet buffer where
+ * the split data (payload) will be placed according to one of of HDS
+ * placement algorithm. The lengths of packet buffers provided for split
+ * data shall be larger than this value.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When one of the HDS placement algorithm is enabled, this value is
+ * used to determine the threshold for HDS placement. Packets with
+ * length larger than this value will be placed according to the HDS
+ * placement algorithm. This value shall be in multiple of 4 bytes.
+ */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_plcmodes_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_plcmodes_qcfg */
+/*
+ * Description: This function can be used to query placement mode configuration
+ * of the VNIC.
+ */
+/* Input (24 bytes) */
+struct hwrm_vnic_plcmodes_qcfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* Logical vnic ID */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_vnic_plcmodes_qcfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint32_t flags;
+ /*
+ * When this bit is '1', the VNIC is configured to use regular placement
+ * algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_REGULAR_PLACEMENT \
+ UINT32_C(0x1)
+ /*
+ * When this bit is '1', the VNIC is configured to use the jumbo
+ * placement algorithm.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_JUMBO_PLACEMENT \
+ UINT32_C(0x2)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for IPv4 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV4 UINT32_C(0x4)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for IPv6 packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_IPV6 UINT32_C(0x8)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for FCoE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_FCOE UINT32_C(0x10)
+ /*
+ * When this bit is '1', the VNIC is configured to enable Header-Data
+ * split for RoCE packets.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_HDS_ROCE UINT32_C(0x20)
+ /*
+ * When this bit is '1', the VNIC is configured to be the default VNIC
+ * of the requesting function.
+ */
+ #define HWRM_VNIC_PLCMODES_QCFG_OUTPUT_FLAGS_DFLT_VNIC UINT32_C(0x40)
+ uint16_t jumbo_thresh;
+ /*
+ * When jumbo placement algorithm is enabled, this value is used to
+ * determine the threshold for jumbo placement. Packets with length
+ * larger than this value will be placed according to the jumbo
+ * placement algorithm.
+ */
+ uint16_t hds_offset;
+ /*
+ * This value is used to determine the offset into packet buffer where
+ * the split data (payload) will be placed according to one of of HDS
+ * placement algorithm. The lengths of packet buffers provided for split
+ * data shall be larger than this value.
+ */
+ uint16_t hds_threshold;
+ /*
+ * When one of the HDS placement algorithm is enabled, this value is
+ * used to determine the threshold for HDS placement. Packets with
+ * length larger than this value will be placed according to the HDS
+ * placement algorithm. This value shall be in multiple of 4 bytes.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cos_lb_ctx_alloc */
+/* Description: This function is used to allocate COS/Load Balance context. */
+/* Input (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t rss_cos_lb_ctx_id;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_vnic_rss_cos_lb_ctx_free */
+/* Description: This function can be used to free COS/Load Balance context. */
+/* Input (24 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t rss_cos_lb_ctx_id;
+ /* rss_cos_lb_ctx_id is 16 b */
+ uint16_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_vnic_rss_cos_lb_ctx_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_alloc */
+/*
+ * Description: This command allocates and does basic preparation for a ring.
+ */
+/* Input (80 bytes) */
+struct hwrm_ring_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the Reserved1 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED1 UINT32_C(0x1)
+ /* This bit must be '1' for the ring_arb_cfg field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RING_ARB_CFG UINT32_C(0x2)
+ /* This bit must be '1' for the Reserved3 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED3 UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the stat_ctx_id_valid field to be
+ * configured.
+ */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_STAT_CTX_ID_VALID UINT32_C(0x8)
+ /* This bit must be '1' for the Reserved4 field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_RESERVED4 UINT32_C(0x10)
+ /* This bit must be '1' for the max_bw_valid field to be configured. */
+ #define HWRM_RING_ALLOC_INPUT_ENABLES_MAX_BW_VALID UINT32_C(0x20)
+ uint8_t ring_type;
+ /* Ring Type. */
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_ALLOC_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint64_t page_tbl_addr;
+ /* This value is a pointer to the page table for the Ring. */
+ uint32_t fbo;
+ /* First Byte Offset of the first entry in the first page. */
+ uint8_t page_size;
+ /*
+ * Actual page size in 2^page_size. The supported range is
+ * increments in powers of 2 from 16 bytes to 1GB. - 4 = 16 B
+ * Page size is 16 B. - 12 = 4 KB Page size is 4 KB. - 13 = 8 KB
+ * Page size is 8 KB. - 16 = 64 KB Page size is 64 KB. - 21 = 2
+ * MB Page size is 2 MB. - 22 = 4 MB Page size is 4 MB. - 30 = 1
+ * GB Page size is 1 GB.
+ */
+ uint8_t page_tbl_depth;
+ /*
+ * This value indicates the depth of page table. For this
+ * version of the specification, value other than 0 or 1 shall
+ * be considered as an invalid value. When the page_tbl_depth =
+ * 0, then it is treated as a special case with the following.
+ * 1. FBO and page size fields are not valid. 2. page_tbl_addr
+ * is the physical address of the first element of the ring.
+ */
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t length;
+ /*
+ * Number of 16B units in the ring. Minimum size for a ring is
+ * 16 16B entries.
+ */
+ uint16_t logical_id;
+ /*
+ * Logical ring number for the ring to be allocated. This value
+ * determines the position in the doorbell area where the update
+ * to the ring will be made. For completion rings, this value is
+ * also the MSI-X vector number for the function the completion
+ * ring is associated with.
+ */
+ uint16_t cmpl_ring_id;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * value indicates what completion ring the TX ring is
+ * associated with.
+ */
+ uint16_t queue_id;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * value indicates what CoS queue the TX ring is associated
+ * with.
+ */
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint32_t reserved1;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint16_t ring_arb_cfg;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * field is used to configure arbitration related parameters for
+ * a TX ring.
+ */
+ /* Arbitration policy used for the ring. */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_MASK UINT32_C(0xf)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SFT 0
+ /*
+ * Use strict priority for the TX ring. Priority
+ * value is specified in arb_policy_param
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_SP \
+ (UINT32_C(0x1) << 0)
+ /*
+ * Use weighted fair queue arbitration for the
+ * TX ring. Weight is specified in
+ * arb_policy_param
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ \
+ (UINT32_C(0x2) << 0)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_LAST \
+ RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_WFQ
+ /* Reserved field. */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_MASK UINT32_C(0xf0)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_RSVD_SFT 4
+ /*
+ * Arbitration policy specific parameter. # For strict priority
+ * arbitration policy, this field represents a priority value.
+ * If set to 0, then the priority is not specified and the HWRM
+ * is allowed to select any priority for this TX ring. # For
+ * weighted fair queue arbitration policy, this field represents
+ * a weight value. If set to 0, then the weight is not specified
+ * and the HWRM is allowed to select any weight for this TX
+ * ring.
+ */
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_MASK \
+ UINT32_C(0xff00)
+ #define HWRM_RING_ALLOC_INPUT_RING_ARB_CFG_ARB_POLICY_PARAM_SFT 8
+ uint8_t unused_6;
+ uint8_t unused_7;
+ uint32_t reserved3;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t stat_ctx_id;
+ /*
+ * This field is used only when ring_type is a TX ring. This
+ * input indicates what statistics context this ring should be
+ * associated with.
+ */
+ uint32_t reserved4;
+ /* This field is reserved for the future use. It shall be set to 0. */
+ uint32_t max_bw;
+ /*
+ * This field is used only when ring_type is a TX ring to
+ * specify maximum BW allocated to the TX ring. The HWRM will
+ * translate this value into byte counter and time interval used
+ * for this ring inside the device.
+ */
+ /* The bandwidth value. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_MASK UINT32_C(0xfffffff)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_SFT 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BITS (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES (UINT32_C(0x1) << 28)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_SCALE_LAST \
+ RING_ALLOC_INPUT_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_SFT 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_LAST \
+ RING_ALLOC_INPUT_MAX_BW_BW_VALUE_UNIT_INVALID
+ uint8_t int_mode;
+ /*
+ * This field is used only when ring_type is a Completion ring.
+ * This value indicates what interrupt mode should be used on
+ * this completion ring. Note: In the legacy interrupt mode, no
+ * more than 16 completion rings are allowed.
+ */
+ /* Legacy INTA */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_LEGACY UINT32_C(0x0)
+ /* Reserved */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_RSVD UINT32_C(0x1)
+ /* MSI-X */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_MSIX UINT32_C(0x2)
+ /* No Interrupt - Polled mode */
+ #define HWRM_RING_ALLOC_INPUT_INT_MODE_POLL UINT32_C(0x3)
+ uint8_t unused_8[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t ring_id;
+ /*
+ * Physical number of ring allocated. This value shall be unique
+ * for a ring type.
+ */
+ uint16_t logical_ring_id;
+ /* Logical number of ring allocated. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_free */
+/*
+ * Description: This command is used to free a ring and associated resources.
+ * With QoS and DCBx agents, it is possible the traffic classes will be moved
+ * from one CoS queue to another. When this occurs, the driver shall call
+ * 'hwrm_ring_free' to free the allocated rings and then call 'hwrm_ring_alloc'
+ * to re-allocate each ring and assign it to a new CoS queue. hwrm_ring_free
+ * shall be called on a ring only after it has been idle for 500ms or more and
+ * no frames have been posted to the ring during this time. All frames queued
+ * for transmission shall be completed and at least 500ms time elapsed from the
+ * last completion before calling this command.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t ring_type;
+ /* Ring Type. */
+ /* L2 Completion Ring (CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_L2_CMPL UINT32_C(0x0)
+ /* TX Ring (TR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_TX UINT32_C(0x1)
+ /* RX Ring (RR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_RX UINT32_C(0x2)
+ /* RoCE Notification Completion Ring (ROCE_CR) */
+ #define HWRM_RING_FREE_INPUT_RING_TYPE_ROCE_CMPL UINT32_C(0x3)
+ uint8_t unused_0;
+ uint16_t ring_id;
+ /* Physical number of ring allocated. */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_grp_alloc */
+/*
+ * Description: This API allocates and does basic preparation for a ring group.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_grp_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint16_t cr;
+ /* This value identifies the CR associated with the ring group. */
+ uint16_t rr;
+ /* This value identifies the main RR associated with the ring group. */
+ uint16_t ar;
+ /*
+ * This value identifies the aggregation RR associated with the
+ * ring group. If this value is 0xFF... (All Fs), then no
+ * Aggregation ring will be set.
+ */
+ uint16_t sc;
+ /*
+ * This value identifies the statistics context associated with
+ * the ring group.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_grp_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t ring_group_id;
+ /*
+ * This is the ring group ID value. Use this value to program
+ * the default ring group for the VNIC or as table entries in an
+ * RSS/COS context.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_ring_grp_free */
+/*
+ * Description: This API frees a ring group and associated resources. # If a
+ * ring in the ring group is reset or free, then the associated rings in the
+ * ring group shall also be reset/free using hwrm_ring_free. # A function driver
+ * shall always use hwrm_ring_grp_free after freeing all rings in a group. # As
+ * a part of executing this command, the HWRM shall reset all associated ring
+ * group resources.
+ */
+/* Input (24 bytes) */
+struct hwrm_ring_grp_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t ring_group_id;
+ /* This is the ring group ID value. */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_ring_grp_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_alloc */
+/*
+ * Description: An L2 filter is a filter resource that is used to identify a
+ * vnic or ring for a packet based on layer 2 fields. Layer 2 fields for
+ * encapsulated packets include both outer L2 header and/or inner l2 header of
+ * encapsulated packet. The L2 filter resource covers the following OS specific
+ * L2 filters. Linux/FreeBSD (per function): # Broadcast enable/disable # List
+ * of individual multicast filters # All multicast enable/disable filter #
+ * Unicast filters # Promiscuous mode VMware: # Broadcast enable/disable (per
+ * physical function) # All multicast enable/disable (per function) # Unicast
+ * filters per ring or vnic # Promiscuous mode per PF Windows: # Broadcast
+ * enable/disable (per physical function) # List of individual multicast filters
+ * (Driver needs to advertise the maximum number of filters supported) # All
+ * multicast enable/disable per physical function # Unicast filters per vnic #
+ * Promiscuous mode per PF Implementation notes on the use of VNIC in this
+ * command: # By default, these filters belong to default vnic for the function.
+ * # Once these filters are set up, only destination VNIC can be modified. # If
+ * the destination VNIC is not specified in this command, then the HWRM shall
+ * only create an l2 context id. HWRM Implementation notes for multicast
+ * filters: # The hwrm_filter_alloc command can be used to set up multicast
+ * filters (perfect match or partial match). Each individual function driver can
+ * set up multicast filters independently. # The HWRM needs to keep track of
+ * multicast filters set up by function drivers and maintain multicast group
+ * replication records to enable a subset of functions to receive traffic for a
+ * specific multicast address. # When a specific multicast filter cannot be set,
+ * the HWRM shall return an error. In this error case, the driver should fall
+ * back to using one general filter (rather than specific) for all multicast
+ * traffic. # When the SR-IOV is enabled, the HWRM needs to additionally track
+ * source knockout per multicast group record. Examples of setting unicast
+ * filters: For a unicast MAC based filter, one can use a combination of the
+ * fields and masks provided in this command to set up the filter. Below are
+ * some examples: # MAC + no VLAN filter: This filter is used to identify
+ * traffic that does not contain any VLAN tags and matches destination (or
+ * source) MAC address. This filter can be set up by setting only l2_addr field
+ * to be a valid field. All other fields are not valid. The following value is
+ * set for l2_addr. l2_addr = MAC # MAC + Any VLAN filter: This filter is used
+ * to identify traffic that carries single VLAN tag and matches (destination or
+ * source) MAC address. This filter can be set up by setting only l2_addr and
+ * l2_ovlan_mask fields to be valid fields. All other fields are not valid. The
+ * following values are set for those two valid fields. l2_addr = MAC,
+ * l2_ovlan_mask = 0xFFFF # MAC + no VLAN or VLAN ID=0: This filter is used to
+ * identify untagged traffic that does not contain any VLAN tags or a VLAN tag
+ * with VLAN ID = 0 and matches destination (or source) MAC address. This filter
+ * can be set up by setting only l2_addr and l2_ovlan fields to be valid fields.
+ * All other fields are not valid. The following value are set for l2_addr and
+ * l2_ovlan. l2_addr = MAC, l2_ovlan = 0x0 # MAC + no VLAN or any VLAN: This
+ * filter is used to identify traffic that contains zero or 1 VLAN tag and
+ * matches destination (or source) MAC address. This filter can be set up by
+ * setting only l2_addr, l2_ovlan, and l2_mask fields to be valid fields. All
+ * other fields are not valid. The following value are set for l2_addr,
+ * l2_ovlan, and l2_mask fields. l2_addr = MAC, l2_ovlan = 0x0, l2_ovlan_mask =
+ * 0xFFFF # MAC + VLAN ID filter: This filter can be set up by setting only
+ * l2_addr, l2_ovlan, and l2_ovlan_mask fields to be valid fields. All other
+ * fields are not valid. The following values are set for those three valid
+ * fields. l2_addr = MAC, l2_ovlan = VLAN ID, l2_ovlan_mask = 0xF000
+ */
+/* Input (96 bytes) */
+struct hwrm_cfa_l2_filter_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_TX \
+ (UINT32_C(0x0) << 0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX \
+ (UINT32_C(0x1) << 0)
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_LAST \
+ CFA_L2_FILTER_ALLOC_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates the applicability to the
+ * loopback path.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x4)
+ /*
+ * If this flag is set, all t_l2_* fields are invalid and they
+ * should not be specified. If this flag is set, then l2_*
+ * fields refer to fields of outermost L2 header.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_FLAGS_OUTERMOST UINT32_C(0x8)
+ uint32_t enables;
+ /* This bit must be '1' for the l2_addr field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR UINT32_C(0x1)
+ /* This bit must be '1' for the l2_addr_mask field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR_MASK \
+ UINT32_C(0x2)
+ /* This bit must be '1' for the l2_ovlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the l2_ovlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_OVLAN_MASK \
+ UINT32_C(0x8)
+ /* This bit must be '1' for the l2_ivlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the l2_ivlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN_MASK \
+ UINT32_C(0x20)
+ /* This bit must be '1' for the t_l2_addr field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the t_l2_addr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_ADDR_MASK \
+ UINT32_C(0x80)
+ /* This bit must be '1' for the t_l2_ovlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the t_l2_ovlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_OVLAN_MASK \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the t_l2_ivlan field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the t_l2_ivlan_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_T_L2_IVLAN_MASK \
+ UINT32_C(0x800)
+ /* This bit must be '1' for the src_type field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_TYPE UINT32_C(0x1000)
+ /* This bit must be '1' for the src_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_SRC_ID UINT32_C(0x2000)
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x4000)
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_DST_ID UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x10000)
+ uint8_t l2_addr[6];
+ /*
+ * This value sets the match value for the L2 MAC address.
+ * Destination MAC address for RX path. Source MAC address for
+ * TX path.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t l2_addr_mask[6];
+ /*
+ * This value sets the mask value for the L2 address. A value of
+ * 0 will mask the corresponding bit from compare.
+ */
+ uint16_t l2_ovlan;
+ /* This value sets VLAN ID value for outer VLAN. */
+ uint16_t l2_ovlan_mask;
+ /*
+ * This value sets the mask value for the ovlan id. A value of 0
+ * will mask the corresponding bit from compare.
+ */
+ uint16_t l2_ivlan;
+ /* This value sets VLAN ID value for inner VLAN. */
+ uint16_t l2_ivlan_mask;
+ /*
+ * This value sets the mask value for the ivlan id. A value of 0
+ * will mask the corresponding bit from compare.
+ */
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t t_l2_addr[6];
+ /*
+ * This value sets the match value for the tunnel L2 MAC
+ * address. Destination MAC address for RX path. Source MAC
+ * address for TX path.
+ */
+ uint8_t unused_4;
+ uint8_t unused_5;
+ uint8_t t_l2_addr_mask[6];
+ /*
+ * This value sets the mask value for the tunnel L2 address. A
+ * value of 0 will mask the corresponding bit from compare.
+ */
+ uint16_t t_l2_ovlan;
+ /* This value sets VLAN ID value for tunnel outer VLAN. */
+ uint16_t t_l2_ovlan_mask;
+ /*
+ * This value sets the mask value for the tunnel ovlan id. A
+ * value of 0 will mask the corresponding bit from compare.
+ */
+ uint16_t t_l2_ivlan;
+ /* This value sets VLAN ID value for tunnel inner VLAN. */
+ uint16_t t_l2_ivlan_mask;
+ /*
+ * This value sets the mask value for the tunnel ivlan id. A
+ * value of 0 will mask the corresponding bit from compare.
+ */
+ uint8_t src_type;
+ /* This value identifies the type of source of the packet. */
+ /* Network port */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_NPORT UINT32_C(0x0)
+ /* Physical function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_PF UINT32_C(0x1)
+ /* Virtual function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VF UINT32_C(0x2)
+ /* Virtual NIC of a function */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_VNIC UINT32_C(0x3)
+ /* Embedded processor for CFA management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_KONG UINT32_C(0x4)
+ /* Embedded processor for OOB management */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_APE UINT32_C(0x5)
+ /* Embedded processor for RoCE */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_BONO UINT32_C(0x6)
+ /* Embedded processor for network proxy functions */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_SRC_TYPE_TANG UINT32_C(0x7)
+ uint8_t unused_6;
+ uint32_t src_id;
+ /*
+ * This value is the id of the source. For a network port, it
+ * represents port_id. For a physical function, it represents
+ * fid. For a virtual function, it represents vf_id. For a vnic,
+ * it represents vnic_id. For embedded processors, this id is
+ * not valid. Notes: 1. The function ID is implied if it src_id
+ * is not provided for a src_type that is either
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /*
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /*
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT UINT32_C(0x7)
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE UINT32_C(0x8)
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ uint8_t unused_7;
+ uint16_t dst_id;
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint16_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint8_t pri_hint;
+ /*
+ * This hint is provided to help in placing the filter in the
+ * filter table.
+ */
+ /* No preference */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
+ UINT32_C(0x0)
+ /* Above the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE_FILTER \
+ UINT32_C(0x1)
+ /* Below the given filter */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_BELOW_FILTER \
+ UINT32_C(0x2)
+ /* As high as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MAX UINT32_C(0x3)
+ /* As low as possible */
+ #define HWRM_CFA_L2_FILTER_ALLOC_INPUT_PRI_HINT_MIN UINT32_C(0x4)
+ uint8_t unused_8;
+ uint32_t unused_9;
+ uint64_t l2_filter_id_hint;
+ /*
+ * This is the ID of the filter that goes along with the
+ * pri_hint. This field is valid only for the following values.
+ * 1 - Above the given filter 2 - Below the given filter
+ */
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_cfa_l2_filter_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint32_t flow_id;
+ /*
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_free */
+/*
+ * Description: Free a L2 filter. The HWRM shall free all associated filter
+ * resources with the L2 filter.
+ */
+/* Input (24 bytes) */
+struct hwrm_cfa_l2_filter_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_filter_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_filter_cfg */
+/* Description: Change the configuration of an existing L2 filter */
+/* Input (40 bytes) */
+struct hwrm_cfa_l2_filter_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_TX \
+ (UINT32_C(0x0) << 0)
+ /* rx path */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX \
+ (UINT32_C(0x1) << 0)
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_LAST \
+ CFA_L2_FILTER_CFG_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_FLAGS_DROP UINT32_C(0x2)
+ uint32_t enables;
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_DST_ID UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_L2_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
+ UINT32_C(0x2)
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint32_t dst_id;
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint32_t new_mirror_vnic_id;
+ /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_filter_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_l2_set_rx_mask */
+/* Description: This command will set rx mask of the function. */
+/* Input (56 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t vnic_id;
+ /* VNIC ID */
+ uint32_t mask;
+ /* Reserved for future use. */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_RESERVED UINT32_C(0x1)
+ /*
+ * When this bit is '1', the function is requested to accept
+ * multi-cast packets specified by the multicast addr table.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_MCAST UINT32_C(0x2)
+ /*
+ * When this bit is '1', the function is requested to accept all
+ * multi-cast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ALL_MCAST UINT32_C(0x4)
+ /*
+ * When this bit is '1', the function is requested to accept
+ * broadcast packets.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_BCAST UINT32_C(0x8)
+ /*
+ * When this bit is '1', the function is requested to be put in
+ * the promiscuous mode. The HWRM should accept any function to
+ * set up promiscuous mode. The HWRM shall follow the semantics
+ * below for the promiscuous mode support. # When partitioning
+ * is not enabled on a port (i.e. single PF on the port), then
+ * the PF shall be allowed to be in the promiscuous mode. When
+ * the PF is in the promiscuous mode, then it shall receive all
+ * host bound traffic on that port. # When partitioning is
+ * enabled on a port (i.e. multiple PFs per port) and a PF on
+ * that port is in the promiscuous mode, then the PF receives
+ * all traffic within that partition as identified by a unique
+ * identifier for the PF (e.g. S-Tag). If a unique outer VLAN
+ * for the PF is specified, then the setting of promiscuous mode
+ * on that PF shall result in the PF receiving all host bound
+ * traffic with matching outer VLAN. # A VF shall can be set in
+ * the promiscuous mode. In the promiscuous mode, the VF does
+ * not receive any traffic unless a unique outer VLAN for the VF
+ * is specified. If a unique outer VLAN for the VF is specified,
+ * then the setting of promiscuous mode on that VF shall result
+ * in the VF receiving all host bound traffic with the matching
+ * outer VLAN. # The HWRM shall allow the setting of promiscuous
+ * mode on a function independently from the promiscuous mode
+ * settings on other functions.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_PROMISCUOUS UINT32_C(0x10)
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for the outermost
+ * Layer 2 destination MAC address field.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_OUTERMOST UINT32_C(0x20)
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for the VLAN-
+ * tagged packets that match the TPID and VID fields of VLAN
+ * tags in the VLAN tag table specified in this command.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLANONLY UINT32_C(0x40)
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for non-VLAN
+ * tagged packets and VLAN-tagged packets that match the TPID
+ * and VID fields of VLAN tags in the VLAN tag table specified
+ * in this command.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_VLAN_NONVLAN UINT32_C(0x80)
+ /*
+ * If this flag is set, the corresponding RX filters shall be
+ * set up to cover multicast/broadcast filters for non-VLAN
+ * tagged packets and VLAN-tagged packets matching any VLAN tag.
+ * If this flag is set, then the HWRM shall ignore VLAN tags
+ * specified in vlan_tag_tbl. If none of vlanonly, vlan_nonvlan,
+ * and anyvlan_nonvlan flags is set, then the HWRM shall ignore
+ * VLAN tags specified in vlan_tag_tbl. The HWRM client shall
+ * set at most one flag out of vlanonly, vlan_nonvlan, and
+ * anyvlan_nonvlan.
+ */
+ #define HWRM_CFA_L2_SET_RX_MASK_INPUT_MASK_ANYVLAN_NONVLAN \
+ UINT32_C(0x100)
+ uint64_t mc_tbl_addr;
+ /* This is the address for mcast address tbl. */
+ uint32_t num_mc_entries;
+ /*
+ * This value indicates how many entries in mc_tbl are valid.
+ * Each entry is 6 bytes.
+ */
+ uint32_t unused_0;
+ uint64_t vlan_tag_tbl_addr;
+ /*
+ * This is the address for VLAN tag table. Each VLAN entry in
+ * the table is 4 bytes of a VLAN tag including TPID, PCP, DEI,
+ * and VID fields in network byte order.
+ */
+ uint32_t num_vlan_tags;
+ /*
+ * This value indicates how many entries in vlan_tag_tbl are
+ * valid. Each entry is 4 bytes.
+ */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_cfa_l2_set_rx_mask_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_UNKNOWN UINT32_C(0x0)
+ /*
+ * Unable to complete operation due to conflict
+ * with Ntuple Filter
+ */
+ #define \
+ HWRM_CFA_L2_SET_RX_MASK_CMD_ERR_CODE_NTUPLE_FILTER_CONFLICT_ERR \
+ UINT32_C(0x1)
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_cfa_vlan_antispoof_cfg */
+/* Description: Configures vlan anti-spoof filters for VF. */
+/* Input (32 bytes) */
+struct hwrm_cfa_vlan_antispoof_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids
+ * 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written when the
+ * request is complete. This area must be 16B aligned and must be
+ * cleared to zero before the request is made.
+ */
+ uint16_t fid;
+ /*
+ * Function ID of the function that is being configured. Only valid for
+ * a VF FID configured by the PF.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint32_t num_vlan_entries;
+ /* Number of VLAN entries in the vlan_tag_mask_tbl. */
+ uint64_t vlan_tag_mask_tbl_addr;
+ /*
+ * The vlan_tag_mask_tbl_addr is the DMA address of the VLAN antispoof
+ * table. Each table entry contains the 16-bit TPID (0x8100 or 0x88a8
+ * only), 16-bit VLAN ID, and a 16-bit mask, all in network order to
+ * match hwrm_cfa_l2_set_rx_mask. For an individual VLAN entry, the mask
+ * value should be 0xfff for the 12-bit VLAN ID.
+ */
+};
+
+/* Output (16 bytes) */
+struct hwrm_cfa_vlan_antispoof_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in parameters,
+ * and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last byte of
+ * the response is a valid flag that will read as '1' when the command
+ * has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the output is
+ * completely written to RAM. This field should be read as '1' to
+ * indicate that the output has been completely written. When writing a
+ * command completion or response to an internal processor, the order of
+ * writes has to be such that this field is written last.
+ */
+};
+
+/* hwrm_cfa_ntuple_filter_alloc */
+/*
+ * Description: This is a ntuple filter that uses fields from L4/L3 header and
+ * optionally fields from L2. The ntuple filters apply to receive traffic only.
+ * All L2/L3/L4 header fields are specified in network byte order. These filters
+ * can be used for Receive Flow Steering (RFS). # For ethertype value, only
+ * 0x0800 (IPv4) and 0x86dd (IPv6) shall be supported for ntuple filters. # If a
+ * field specified in this command is not enabled as a valid field, then that
+ * field shall not be used in matching packet header fields against this filter.
+ */
+/* Input (128 bytes) */
+struct hwrm_cfa_ntuple_filter_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Setting of this flag indicates the applicability to the
+ * loopback path.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x1)
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates that a meter is expected to be
+ * attached to this flow. This hint can be used when choosing
+ * the action record format required for the flow.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_FLAGS_METER UINT32_C(0x4)
+ uint32_t enables;
+ /* This bit must be '1' for the l2_filter_id field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
+ UINT32_C(0x1)
+ /* This bit must be '1' for the ethertype field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_ETHERTYPE \
+ UINT32_C(0x2)
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x4)
+ /* This bit must be '1' for the src_macaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_MACADDR \
+ UINT32_C(0x8)
+ /* This bit must be '1' for the ipaddr_type field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IPADDR_TYPE \
+ UINT32_C(0x10)
+ /* This bit must be '1' for the src_ipaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the src_ipaddr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_IPADDR_MASK \
+ UINT32_C(0x40)
+ /* This bit must be '1' for the dst_ipaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the dst_ipaddr_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_IPADDR_MASK \
+ UINT32_C(0x100)
+ /* This bit must be '1' for the ip_protocol field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_IP_PROTOCOL \
+ UINT32_C(0x200)
+ /* This bit must be '1' for the src_port field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT \
+ UINT32_C(0x400)
+ /*
+ * This bit must be '1' for the src_port_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_SRC_PORT_MASK \
+ UINT32_C(0x800)
+ /* This bit must be '1' for the dst_port field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT \
+ UINT32_C(0x1000)
+ /*
+ * This bit must be '1' for the dst_port_mask field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_PORT_MASK \
+ UINT32_C(0x2000)
+ /* This bit must be '1' for the pri_hint field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_PRI_HINT \
+ UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the ntuple_filter_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_NTUPLE_FILTER_ID \
+ UINT32_C(0x8000)
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_ID \
+ UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x20000)
+ /* This bit must be '1' for the dst_macaddr field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_ENABLES_DST_MACADDR \
+ UINT32_C(0x40000)
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint8_t src_macaddr[6];
+ /*
+ * This value indicates the source MAC address in the Ethernet
+ * header.
+ */
+ uint16_t ethertype;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint8_t ip_addr_type;
+ /*
+ * This value indicates the type of IP address. 4 - IPv4 6 -
+ * IPv6 All others are invalid.
+ */
+ /* invalid */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN \
+ UINT32_C(0x0)
+ /* IPv4 */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 \
+ UINT32_C(0x4)
+ /* IPv6 */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 \
+ UINT32_C(0x6)
+ uint8_t ip_protocol;
+ /*
+ * The value of protocol filed in IP header. Applies to UDP and
+ * TCP traffic. 6 - TCP 17 - UDP
+ */
+ /* invalid */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN \
+ UINT32_C(0x0)
+ /* TCP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_TCP \
+ UINT32_C(0x6)
+ /* UDP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_IP_PROTOCOL_UDP \
+ UINT32_C(0x11)
+ uint16_t dst_id;
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint16_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint8_t tunnel_type;
+ /*
+ * This value indicates the tunnel type for this filter. If this
+ * field is not specified, then the filter shall apply to both
+ * non-tunneled and tunneled packets. If this field conflicts
+ * with the tunnel_type specified in the l2_filter_id, then the
+ * HWRM shall return an error for this command.
+ */
+ /* Non-tunnel */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /*
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /*
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT UINT32_C(0x7)
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ uint8_t pri_hint;
+ /*
+ * This hint is provided to help in placing the filter in the
+ * filter table.
+ */
+ /* No preference */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_NO_PREFER \
+ UINT32_C(0x0)
+ /* Above the given filter */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_ABOVE UINT32_C(0x1)
+ /* Below the given filter */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_BELOW UINT32_C(0x2)
+ /* As high as possible */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_HIGHEST \
+ UINT32_C(0x3)
+ /* As low as possible */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_INPUT_PRI_HINT_LOWEST UINT32_C(0x4)
+ uint32_t src_ipaddr[4];
+ /*
+ * The value of source IP address to be used in filtering. For
+ * IPv4, first four bytes represent the IP address.
+ */
+ uint32_t src_ipaddr_mask[4];
+ /*
+ * The value of source IP address mask to be used in filtering.
+ * For IPv4, first four bytes represent the IP address mask.
+ */
+ uint32_t dst_ipaddr[4];
+ /*
+ * The value of destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t dst_ipaddr_mask[4];
+ /*
+ * The value of destination IP address mask to be used in
+ * filtering. For IPv4, first four bytes represent the IP
+ * address mask.
+ */
+ uint16_t src_port;
+ /*
+ * The value of source port to be used in filtering. Applies to
+ * UDP and TCP traffic.
+ */
+ uint16_t src_port_mask;
+ /*
+ * The value of source port mask to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_port;
+ /*
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_port_mask;
+ /*
+ * The value of destination port mask to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint64_t ntuple_filter_id_hint;
+ /* This is the ID of the filter that goes along with the pri_hint. */
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_cfa_ntuple_filter_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t ntuple_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t flow_id;
+ /*
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* Command specific Error Codes (8 bytes) */
+struct hwrm_cfa_ntuple_filter_alloc_cmd_err {
+ uint8_t code;
+ /*
+ * command specific error codes that goes to the cmd_err field
+ * in Common HWRM Error Response.
+ */
+ /* Unknown error */
+ #define HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_UNKNOWN UINT32_C(0x0)
+ /*
+ * Unable to complete operation due to conflict
+ * with Rx Mask VLAN
+ */
+ #define \
+ HWRM_CFA_NTUPLE_FILTER_ALLOC_CMD_ERR_CODE_RX_MASK_VLAN_CONFLICT_ERR \
+ UINT32_C(0x1)
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* hwrm_cfa_ntuple_filter_free */
+/* Description: Free an ntuple filter */
+/* Input (24 bytes) */
+struct hwrm_cfa_ntuple_filter_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t ntuple_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_ntuple_filter_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_ntuple_filter_cfg */
+/*
+ * Description: Configure an ntuple filter with a new destination VNIC and/or
+ * meter.
+ */
+/* Input (48 bytes) */
+struct hwrm_cfa_ntuple_filter_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the new_dst_id field to be configured. */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_DST_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the new_meter_instance_id field to
+ * be configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
+ UINT32_C(0x4)
+ uint32_t unused_0;
+ uint64_t ntuple_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t new_dst_id;
+ /*
+ * If set, this value shall represent the new Logical VNIC ID of
+ * the destination VNIC for the RX path and new network port id
+ * of the destination port for the TX path.
+ */
+ uint32_t new_mirror_vnic_id;
+ /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint16_t new_meter_instance_id;
+ /*
+ * New meter to attach to the flow. Specifying the invalid
+ * instance ID is used to remove any existing meter from the
+ * flow.
+ */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
+ */
+ #define HWRM_CFA_NTUPLE_FILTER_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ uint16_t unused_1[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_ntuple_filter_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_em_flow_alloc */
+/*
+ * Description: This is a generic Exact Match (EM) flow that uses fields from
+ * L4/L3/L2 headers. The EM flows apply to transmit and receive traffic. All
+ * L2/L3/L4 header fields are specified in network byte order. For each EM flow,
+ * there is an associated set of actions specified. For tunneled packets, all
+ * L2/L3/L4 fields specified are fields of inner headers unless otherwise
+ * specified. # If a field specified in this command is not enabled as a valid
+ * field, then that field shall not be used in matching packet header fields
+ * against this EM flow entry.
+ */
+/* Input (112 bytes) */
+struct hwrm_cfa_em_flow_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource. This
+ * enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_TX \
+ (UINT32_C(0x0) << 0)
+ /* rx path */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX \
+ (UINT32_C(0x1) << 0)
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_LAST \
+ CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PATH_RX
+ /*
+ * Setting of this flag indicates enabling of a byte counter for
+ * a given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_BYTE_CTR UINT32_C(0x2)
+ /*
+ * Setting of this flag indicates enabling of a packet counter
+ * for a given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_PKT_CTR UINT32_C(0x4)
+ /*
+ * Setting of this flag indicates de-capsulation action for the
+ * given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DECAP UINT32_C(0x8)
+ /*
+ * Setting of this flag indicates encapsulation action for the
+ * given flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_ENCAP UINT32_C(0x10)
+ /*
+ * Setting of this flag indicates drop action. If this flag is
+ * not set, then it should be considered accept action.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_DROP UINT32_C(0x20)
+ /*
+ * Setting of this flag indicates that a meter is expected to be
+ * attached to this flow. This hint can be used when choosing
+ * the action record format required for the flow.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_FLAGS_METER UINT32_C(0x40)
+ uint32_t enables;
+ /* This bit must be '1' for the l2_filter_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_L2_FILTER_ID UINT32_C(0x1)
+ /* This bit must be '1' for the tunnel_type field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_TYPE UINT32_C(0x2)
+ /* This bit must be '1' for the tunnel_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_TUNNEL_ID UINT32_C(0x4)
+ /* This bit must be '1' for the src_macaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_MACADDR UINT32_C(0x8)
+ /* This bit must be '1' for the dst_macaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_MACADDR UINT32_C(0x10)
+ /* This bit must be '1' for the ovlan_vid field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_OVLAN_VID UINT32_C(0x20)
+ /* This bit must be '1' for the ivlan_vid field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IVLAN_VID UINT32_C(0x40)
+ /* This bit must be '1' for the ethertype field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ETHERTYPE UINT32_C(0x80)
+ /* This bit must be '1' for the src_ipaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_IPADDR UINT32_C(0x100)
+ /* This bit must be '1' for the dst_ipaddr field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_IPADDR UINT32_C(0x200)
+ /* This bit must be '1' for the ipaddr_type field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IPADDR_TYPE UINT32_C(0x400)
+ /* This bit must be '1' for the ip_protocol field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_IP_PROTOCOL UINT32_C(0x800)
+ /* This bit must be '1' for the src_port field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_SRC_PORT UINT32_C(0x1000)
+ /* This bit must be '1' for the dst_port field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_PORT UINT32_C(0x2000)
+ /* This bit must be '1' for the dst_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_DST_ID UINT32_C(0x4000)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x8000)
+ /*
+ * This bit must be '1' for the encap_record_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_ENCAP_RECORD_ID \
+ UINT32_C(0x10000)
+ /*
+ * This bit must be '1' for the meter_instance_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_ENABLES_METER_INSTANCE_ID \
+ UINT32_C(0x20000)
+ uint64_t l2_filter_id;
+ /*
+ * This value identifies a set of CFA data structures used for
+ * an L2 context.
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Non-tunnel */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN UINT32_C(0x1)
+ /*
+ * Network Virtualization Generic Routing
+ * Encapsulation (NVGRE)
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_NVGRE UINT32_C(0x2)
+ /*
+ * Generic Routing Encapsulation (GRE) inside
+ * Ethernet payload
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_L2GRE UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPIP UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_GENEVE UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_MPLS UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_STT UINT32_C(0x7)
+ /*
+ * Generic Routing Encapsulation (GRE) inside IP
+ * datagram payload
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_IPGRE UINT32_C(0x8)
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 UINT32_C(0x9)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ uint8_t unused_0;
+ uint16_t unused_1;
+ uint32_t tunnel_id;
+ /*
+ * Tunnel identifier. Virtual Network Identifier (VNI). Only
+ * valid with tunnel_types VXLAN, NVGRE, and Geneve. Only lower
+ * 24-bits of VNI field are used in setting up the filter.
+ */
+ uint8_t src_macaddr[6];
+ /*
+ * This value indicates the source MAC address in the Ethernet
+ * header.
+ */
+ uint16_t meter_instance_id;
+ /* The meter instance to attach to the flow. */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
+ */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ uint8_t dst_macaddr[6];
+ /*
+ * This value indicates the destination MAC address in the
+ * Ethernet header.
+ */
+ uint16_t ovlan_vid;
+ /*
+ * This value indicates the VLAN ID of the outer VLAN tag in the
+ * Ethernet header.
+ */
+ uint16_t ivlan_vid;
+ /*
+ * This value indicates the VLAN ID of the inner VLAN tag in the
+ * Ethernet header.
+ */
+ uint16_t ethertype;
+ /* This value indicates the ethertype in the Ethernet header. */
+ uint8_t ip_addr_type;
+ /*
+ * This value indicates the type of IP address. 4 - IPv4 6 -
+ * IPv6 All others are invalid.
+ */
+ /* invalid */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_UNKNOWN UINT32_C(0x0)
+ /* IPv4 */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV4 UINT32_C(0x4)
+ /* IPv6 */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_ADDR_TYPE_IPV6 UINT32_C(0x6)
+ uint8_t ip_protocol;
+ /*
+ * The value of protocol filed in IP header. Applies to UDP and
+ * TCP traffic. 6 - TCP 17 - UDP
+ */
+ /* invalid */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UNKNOWN UINT32_C(0x0)
+ /* TCP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_TCP UINT32_C(0x6)
+ /* UDP */
+ #define HWRM_CFA_EM_FLOW_ALLOC_INPUT_IP_PROTOCOL_UDP UINT32_C(0x11)
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint32_t src_ipaddr[4];
+ /*
+ * The value of source IP address to be used in filtering. For
+ * IPv4, first four bytes represent the IP address.
+ */
+ uint32_t dst_ipaddr[4];
+ /*
+ * big_endian = True The value of destination IP address to be
+ * used in filtering. For IPv4, first four bytes represent the
+ * IP address.
+ */
+ uint16_t src_port;
+ /*
+ * The value of source port to be used in filtering. Applies to
+ * UDP and TCP traffic.
+ */
+ uint16_t dst_port;
+ /*
+ * The value of destination port to be used in filtering.
+ * Applies to UDP and TCP traffic.
+ */
+ uint16_t dst_id;
+ /*
+ * If set, this value shall represent the Logical VNIC ID of the
+ * destination VNIC for the RX path and network port id of the
+ * destination port for the TX path.
+ */
+ uint16_t mirror_vnic_id;
+ /* Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint32_t encap_record_id;
+ /* Logical ID of the encapsulation record. */
+ uint32_t unused_4;
+} __attribute__((packed));
+
+/* Output (24 bytes) */
+struct hwrm_cfa_em_flow_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint64_t em_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t flow_id;
+ /*
+ * This is the ID of the flow associated with this filter. This
+ * value shall be used to match and associate the flow
+ * identifier returned in completion records. A value of
+ * 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_em_flow_free */
+/* Description: Free an EM flow table entry */
+/* Input (24 bytes) */
+struct hwrm_cfa_em_flow_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t em_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_em_flow_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_cfa_em_flow_cfg */
+/*
+ * Description: Configure an EM flow with a new destination VNIC and/or meter.
+ */
+/* Input (48 bytes) */
+struct hwrm_cfa_em_flow_cfg_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t enables;
+ /* This bit must be '1' for the new_dst_id field to be configured. */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_DST_ID UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the new_mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_MIRROR_VNIC_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the new_meter_instance_id field to
+ * be configured.
+ */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_ENABLES_NEW_METER_INSTANCE_ID \
+ UINT32_C(0x4)
+ uint32_t unused_0;
+ uint64_t em_filter_id;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t new_dst_id;
+ /*
+ * If set, this value shall represent the new Logical VNIC ID of
+ * the destination VNIC for the RX path and network port id of
+ * the destination port for the TX path.
+ */
+ uint32_t new_mirror_vnic_id;
+ /* New Logical VNIC ID of the VNIC where traffic is mirrored. */
+ uint16_t new_meter_instance_id;
+ /*
+ * New meter to attach to the flow. Specifying the invalid
+ * instance ID is used to remove any existing meter from the
+ * flow.
+ */
+ /*
+ * A value of 0xfff is considered invalid and
+ * implies the instance is not configured.
+ */
+ #define HWRM_CFA_EM_FLOW_CFG_INPUT_NEW_METER_INSTANCE_ID_INVALID \
+ UINT32_C(0xffff)
+ uint16_t unused_1[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_cfa_em_flow_cfg_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_tunnel_dst_port_query */
+/*
+ * Description: This function is called by a driver to query tunnel type
+ * specific destination port configuration.
+ */
+/* Input (24 bytes) */
+struct hwrm_tunnel_dst_port_query_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_TUNNEL_DST_PORT_QUERY_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ uint8_t unused_0[7];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_tunnel_dst_port_query_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t tunnel_dst_port_id;
+ /*
+ * This field represents the identifier of L4 destination port
+ * used for the given tunnel type. This field is valid for
+ * specific tunnel types that use layer 4 (e.g. UDP) transports
+ * for tunneling.
+ */
+ uint16_t tunnel_dst_port_val;
+ /*
+ * This field represents the value of L4 destination port
+ * identified by tunnel_dst_port_id. This field is valid for
+ * specific tunnel types that use layer 4 (e.g. UDP) transports
+ * for tunneling. This field is in network byte order. A value
+ * of 0 means that the destination port is not configured.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_tunnel_dst_port_alloc */
+/*
+ * Description: This function is called by a driver to allocate l4 destination
+ * port for a specific tunnel type. The destination port value is provided in
+ * the input. If the HWRM supports only one global destination port for a tunnel
+ * type, then the HWRM shall keep track of its usage as described below. # The
+ * first caller that allocates a destination port shall always succeed and the
+ * HWRM shall save the destination port configuration for that tunnel type and
+ * increment the usage count to 1. # Subsequent callers allocating the same
+ * destination port for that tunnel type shall succeed and the HWRM shall
+ * increment the usage count for that port for each subsequent caller that
+ * succeeds. # Any subsequent caller trying to allocate a different destination
+ * port for that tunnel type shall fail until the usage count for the original
+ * destination port goes to zero. # A caller that frees a port will cause the
+ * usage count for that port to decrement.
+ */
+/* Input (24 bytes) */
+struct hwrm_tunnel_dst_port_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN UINT32_C(0x1)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_TUNNEL_DST_PORT_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ uint8_t unused_0;
+ uint16_t tunnel_dst_port_val;
+ /*
+ * This field represents the value of L4 destination port used
+ * for the given tunnel type. This field is valid for specific
+ * tunnel types that use layer 4 (e.g. UDP) transports for
+ * tunneling. This field is in network byte order. A value of 0
+ * shall fail the command.
+ */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_tunnel_dst_port_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint16_t tunnel_dst_port_id;
+ /*
+ * Identifier of a tunnel L4 destination port value. Only
+ * applies to tunnel types that has l4 destination port
+ * parameters.
+ */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t unused_4;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_tunnel_dst_port_free */
+/*
+ * Description: This function is called by a driver to free l4 destination port
+ * for a specific tunnel type.
+ */
+/* Input (24 bytes) */
+struct hwrm_tunnel_dst_port_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint8_t tunnel_type;
+ /* Tunnel Type. */
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN UINT32_C(0x1)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_GENEVE UINT32_C(0x5)
+ /*
+ * IPV4 over virtual eXtensible Local Area
+ * Network (IPV4oVXLAN)
+ */
+ #define HWRM_TUNNEL_DST_PORT_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ uint8_t unused_0;
+ uint16_t tunnel_dst_port_id;
+ /*
+ * Identifier of a tunnel L4 destination port value. Only
+ * applies to tunnel types that has l4 destination port
+ * parameters.
+ */
+ uint32_t unused_1;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_tunnel_dst_port_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t unused_3;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_alloc */
+/*
+ * Description: This command allocates and does basic preparation for a stat
+ * context.
+ */
+/* Input (32 bytes) */
+struct hwrm_stat_ctx_alloc_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint64_t stats_dma_addr;
+ /* This is the address for statistic block. */
+ uint32_t update_period_ms;
+ /*
+ * The statistic block update period in ms. e.g. 250ms, 500ms,
+ * 750ms, 1000ms. If update_period_ms is 0, then the stats
+ * update shall be never done and the DMA address shall not be
+ * used. In this case, the stat block can only be read by
+ * hwrm_stat_ctx_query command.
+ */
+ uint8_t stat_ctx_flags;
+ /*
+ * This field is used to specify statistics context specific
+ * configuration flags.
+ */
+ /*
+ * When this bit is set to '1', the statistics context shall be
+ * allocated for RoCE traffic only. In this case, traffic other
+ * than offloaded RoCE traffic shall not be included in this
+ * statistic context. When this bit is set to '0', the
+ * statistics context shall be used for the network traffic
+ * other than offloaded RoCE traffic.
+ */
+ #define HWRM_STAT_CTX_ALLOC_INPUT_STAT_CTX_FLAGS_ROCE UINT32_C(0x1)
+ uint8_t unused_0[3];
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_alloc_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t stat_ctx_id;
+ /* This is the statistics context ID value. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_free */
+/* Description: This command is used to free a stat context. */
+/* Input (24 bytes) */
+struct hwrm_stat_ctx_free_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format
+ * for the rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request
+ * will be optionally completed on. If the value is -1, then no
+ * CR completion will be generated. Any other value must be a
+ * valid CR ring_id value for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function
+ * ids 0xFFF8 - 0xFFFE - Reserved for internal processors 0xFFFF
+ * - HWRM
+ */
+ uint64_t resp_addr;
+ /*
+ * This is the host address where the response will be written
+ * when the request is complete. This area must be 16B aligned
+ * and must be cleared to zero before the request is made.
+ */
+ uint32_t stat_ctx_id;
+ /* ID of the statistics context that is being queried. */
+ uint32_t unused_0;
+} __attribute__((packed));
+
+/* Output (16 bytes) */
+struct hwrm_stat_ctx_free_output {
+ uint16_t error_code;
+ /*
+ * Pass/Fail or error type Note: receiver to verify the in
+ * parameters, and fail the call with an error when appropriate
+ */
+ uint16_t req_type;
+ /* This field returns the type of original request. */
+ uint16_t seq_id;
+ /* This field provides original sequence number of the command. */
+ uint16_t resp_len;
+ /*
+ * This field is the length of the response in bytes. The last
+ * byte of the response is a valid flag that will read as '1'
+ * when the command has been completely written to memory.
+ */
+ uint32_t stat_ctx_id;
+ /* This is the statistics context ID value. */
+ uint8_t unused_0;
+ uint8_t unused_1;
+ uint8_t unused_2;
+ uint8_t valid;
+ /*
+ * This field is used in Output records to indicate that the
+ * output is completely written to RAM. This field should be
+ * read as '1' to indicate that the output has been completely
+ * written. When writing a command completion or response to an
+ * internal processor, the order of writes has to be such that
+ * this field is written last.
+ */
+} __attribute__((packed));
+
+/* hwrm_stat_ctx_query */
+/* Description: This command returns statistics of a context. */
+/* Input (24 bytes) */
+struct hwrm_stat_ctx_query_input {
+ uint16_t req_type;
+ /*
+ * This value indicates what type of request this is. The format for the
+ * rest of the command is determined by this field.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * This value indicates the what completion ring the request will be
+ * optionally completed on. If the value is -1, then no CR completion
+ * will be generated. Any other value must be a valid CR ring_id value
+ * for this function.
+ */
+ uint16_t seq_id;
+ /* This value indicates the command sequence number. */
+ uint16_t target_id;
+ /*
+ * Target ID of this command. 0x0 - 0xFFF8 - Used for function ids