+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_queue_pfcenable_qcfg_output (size:128b/16B) */
+struct hwrm_queue_pfcenable_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t flags;
+ /* If set to 1, then PFC is enabled on PRI 0. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI0_PFC_ENABLED \
+ UINT32_C(0x1)
+ /* If set to 1, then PFC is enabled on PRI 1. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI1_PFC_ENABLED \
+ UINT32_C(0x2)
+ /* If set to 1, then PFC is enabled on PRI 2. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI2_PFC_ENABLED \
+ UINT32_C(0x4)
+ /* If set to 1, then PFC is enabled on PRI 3. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI3_PFC_ENABLED \
+ UINT32_C(0x8)
+ /* If set to 1, then PFC is enabled on PRI 4. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI4_PFC_ENABLED \
+ UINT32_C(0x10)
+ /* If set to 1, then PFC is enabled on PRI 5. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI5_PFC_ENABLED \
+ UINT32_C(0x20)
+ /* If set to 1, then PFC is enabled on PRI 6. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI6_PFC_ENABLED \
+ UINT32_C(0x40)
+ /* If set to 1, then PFC is enabled on PRI 7. */
+ #define HWRM_QUEUE_PFCENABLE_QCFG_OUTPUT_FLAGS_PRI7_PFC_ENABLED \
+ UINT32_C(0x80)
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/****************************
+ * hwrm_queue_pfcenable_cfg *
+ ****************************/
+
+
+/* hwrm_queue_pfcenable_cfg_input (size:192b/24B) */
+struct hwrm_queue_pfcenable_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* If set to 1, then PFC is requested to be enabled on PRI 0. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI0_PFC_ENABLED \
+ UINT32_C(0x1)
+ /* If set to 1, then PFC is requested to be enabled on PRI 1. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI1_PFC_ENABLED \
+ UINT32_C(0x2)
+ /* If set to 1, then PFC is requested to be enabled on PRI 2. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI2_PFC_ENABLED \
+ UINT32_C(0x4)
+ /* If set to 1, then PFC is requested to be enabled on PRI 3. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI3_PFC_ENABLED \
+ UINT32_C(0x8)
+ /* If set to 1, then PFC is requested to be enabled on PRI 4. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI4_PFC_ENABLED \
+ UINT32_C(0x10)
+ /* If set to 1, then PFC is requested to be enabled on PRI 5. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI5_PFC_ENABLED \
+ UINT32_C(0x20)
+ /* If set to 1, then PFC is requested to be enabled on PRI 6. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI6_PFC_ENABLED \
+ UINT32_C(0x40)
+ /* If set to 1, then PFC is requested to be enabled on PRI 7. */
+ #define HWRM_QUEUE_PFCENABLE_CFG_INPUT_FLAGS_PRI7_PFC_ENABLED \
+ UINT32_C(0x80)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint16_t port_id;
+ uint8_t unused_0[2];
+} __rte_packed;
+
+/* hwrm_queue_pfcenable_cfg_output (size:128b/16B) */
+struct hwrm_queue_pfcenable_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/***************************
+ * hwrm_queue_pri2cos_qcfg *
+ ***************************/
+
+
+/* hwrm_queue_pri2cos_qcfg_input (size:192b/24B) */
+struct hwrm_queue_pri2cos_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX type of the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH UINT32_C(0x1)
+ /* tx path */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_PATH_RX
+ /*
+ * When this bit is set to '0', the query is
+ * for PRI from tunnel headers.
+ * When this bit is set to '1', the query is
+ * for PRI from inner packet headers.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_INPUT_FLAGS_IVLAN UINT32_C(0x2)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ uint8_t unused_0[3];
+} __rte_packed;
+
+/* hwrm_queue_pri2cos_qcfg_output (size:192b/24B) */
+struct hwrm_queue_pri2cos_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /*
+ * CoS Queue assigned to priority 0. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri0_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 1. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri1_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 2. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri2_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 3. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri3_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 4. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri4_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 5. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri5_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 6. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri6_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 7. This value can only
+ * be changed before traffic has started.
+ * A value of 0xff indicates that no CoS queue is assigned to the
+ * specified priority.
+ */
+ uint8_t pri7_cos_queue_id;
+ /* Information about queue configuration. */
+ uint8_t queue_cfg_info;
+ /*
+ * If this flag is set to '1', then the PRI to CoS
+ * configuration is asymmetric on TX and RX sides.
+ * If this flag is set to '0', then PRI to CoS configuration
+ * is symmetric on TX and RX sides.
+ */
+ #define HWRM_QUEUE_PRI2COS_QCFG_OUTPUT_QUEUE_CFG_INFO_ASYM_CFG \
+ UINT32_C(0x1)
+ uint8_t unused_0[6];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_queue_pri2cos_cfg *
+ **************************/
+
+
+/* hwrm_queue_pri2cos_cfg_input (size:320b/40B) */
+struct hwrm_queue_pri2cos_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /*
+ * Enumeration denoting the RX, TX, or both directions applicable to the resource.
+ * This enumeration is used for resources that are similar for both
+ * TX and RX paths of the chip.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_MASK UINT32_C(0x3)
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_SFT 0
+ /* tx path */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_TX UINT32_C(0x0)
+ /* rx path */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_RX UINT32_C(0x1)
+ /* Bi-directional (Symmetrically applicable to TX and RX paths) */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR UINT32_C(0x2)
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_LAST \
+ HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_PATH_BIDIR
+ /*
+ * When this bit is set to '0', the mapping is requested
+ * for PRI from tunnel headers.
+ * When this bit is set to '1', the mapping is requested
+ * for PRI from inner packet headers.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_FLAGS_IVLAN UINT32_C(0x4)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the pri0_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI0_COS_QUEUE_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the pri1_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI1_COS_QUEUE_ID \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the pri2_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI2_COS_QUEUE_ID \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the pri3_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI3_COS_QUEUE_ID \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the pri4_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI4_COS_QUEUE_ID \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the pri5_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI5_COS_QUEUE_ID \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the pri6_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI6_COS_QUEUE_ID \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the pri7_cos_queue_id field to be
+ * configured.
+ */
+ #define HWRM_QUEUE_PRI2COS_CFG_INPUT_ENABLES_PRI7_COS_QUEUE_ID \
+ UINT32_C(0x80)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure pri2cos mapping on this port.
+ */
+ uint8_t port_id;
+ /*
+ * CoS Queue assigned to priority 0. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri0_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 1. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri1_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 2 This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri2_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 3. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri3_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 4. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri4_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 5. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri5_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 6. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri6_cos_queue_id;
+ /*
+ * CoS Queue assigned to priority 7. This value can only
+ * be changed before traffic has started.
+ */
+ uint8_t pri7_cos_queue_id;
+ uint8_t unused_0[7];
+} __rte_packed;
+
+/* hwrm_queue_pri2cos_cfg_output (size:128b/16B) */
+struct hwrm_queue_pri2cos_cfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/**************************
+ * hwrm_queue_cos2bw_qcfg *
+ **************************/
+
+
+/* hwrm_queue_cos2bw_qcfg_input (size:192b/24B) */
+struct hwrm_queue_cos2bw_qcfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure TC BW assignment on this port.
+ */
+ uint16_t port_id;
+ uint8_t unused_0[6];
+} __rte_packed;
+
+/* hwrm_queue_cos2bw_qcfg_output (size:896b/112B) */
+struct hwrm_queue_cos2bw_qcfg_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* ID of CoS Queue 0. */
+ uint8_t queue_id0;
+ uint8_t unused_0;
+ uint16_t unused_1;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id0_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID0_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id0_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id0_bw_weight;
+ /* ID of CoS Queue 1. */
+ uint8_t queue_id1;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id1_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id1_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id1_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID1_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id1_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id1_bw_weight;
+ /* ID of CoS Queue 2. */
+ uint8_t queue_id2;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id2_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id2_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id2_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID2_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id2_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id2_bw_weight;
+ /* ID of CoS Queue 3. */
+ uint8_t queue_id3;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id3_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id3_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id3_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID3_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id3_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id3_bw_weight;
+ /* ID of CoS Queue 4. */
+ uint8_t queue_id4;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id4_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id4_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id4_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID4_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id4_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id4_bw_weight;
+ /* ID of CoS Queue 5. */
+ uint8_t queue_id5;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id5_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id5_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id5_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID5_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id5_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id5_bw_weight;
+ /* ID of CoS Queue 6. */
+ uint8_t queue_id6;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id6_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id6_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id6_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID6_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id6_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id6_bw_weight;
+ /* ID of CoS Queue 7. */
+ uint8_t queue_id7;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id7_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id7_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_MAX_BW_BW_VALUE_UNIT_INVALID
+ /* Transmission Selection Algorithm (TSA) for CoS Queue. */
+ uint8_t queue_id7_tsa_assign;
+ /* Strict Priority */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_SP \
+ UINT32_C(0x0)
+ /* Enhanced Transmission Selection */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_ETS \
+ UINT32_C(0x1)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_FIRST \
+ UINT32_C(0x2)
+ /* reserved. */
+ #define HWRM_QUEUE_COS2BW_QCFG_OUTPUT_QUEUE_ID7_TSA_ASSIGN_RESERVED_LAST \
+ UINT32_C(0xff)
+ /*
+ * Priority level for strict priority. Valid only when the
+ * tsa_assign is 0 - Strict Priority (SP)
+ * 0..7 - Valid values.
+ * 8..255 - Reserved.
+ */
+ uint8_t queue_id7_pri_lvl;
+ /*
+ * Weight used to allocate remaining BW for this COS after
+ * servicing guaranteed bandwidths for all COS.
+ */
+ uint8_t queue_id7_bw_weight;
+ uint8_t unused_2[4];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __rte_packed;
+
+/*************************
+ * hwrm_queue_cos2bw_cfg *
+ *************************/
+
+
+/* hwrm_queue_cos2bw_cfg_input (size:1024b/128B) */
+struct hwrm_queue_cos2bw_cfg_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFC, 0xFFFE - Reserved for internal processors
+ * * 0xFFFD - Reserved for user-space HWRM interface
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ uint32_t enables;
+ /*
+ * If this bit is set to 1, then all queue_id0 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID0_VALID \
+ UINT32_C(0x1)
+ /*
+ * If this bit is set to 1, then all queue_id1 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID1_VALID \
+ UINT32_C(0x2)
+ /*
+ * If this bit is set to 1, then all queue_id2 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID2_VALID \
+ UINT32_C(0x4)
+ /*
+ * If this bit is set to 1, then all queue_id3 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID3_VALID \
+ UINT32_C(0x8)
+ /*
+ * If this bit is set to 1, then all queue_id4 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID4_VALID \
+ UINT32_C(0x10)
+ /*
+ * If this bit is set to 1, then all queue_id5 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID5_VALID \
+ UINT32_C(0x20)
+ /*
+ * If this bit is set to 1, then all queue_id6 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID6_VALID \
+ UINT32_C(0x40)
+ /*
+ * If this bit is set to 1, then all queue_id7 related
+ * parameters in this command are valid.
+ */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_ENABLES_COS_QUEUE_ID7_VALID \
+ UINT32_C(0x80)
+ /*
+ * Port ID of port for which the table is being configured.
+ * The HWRM needs to check whether this function is allowed
+ * to configure TC BW assignment on this port.
+ */
+ uint16_t port_id;
+ /* ID of CoS Queue 0. */
+ uint8_t queue_id0;
+ uint8_t unused_0;
+ /*
+ * Minimum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_min_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_GIGA \
+ (UINT32_C(0x6) << 29)
+ /* Value is in 1/100th of a percentage of total bandwidth. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_PERCENT1_100 \
+ (UINT32_C(0x1) << 29)
+ /* Invalid unit */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID \
+ (UINT32_C(0x7) << 29)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MIN_BW_BW_VALUE_UNIT_INVALID
+ /*
+ * Maximum BW allocated to CoS Queue.
+ * The HWRM will translate this value into byte counter and
+ * time interval used for this COS inside the device.
+ */
+ uint32_t queue_id0_max_bw;
+ /* The bandwidth value. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_MASK \
+ UINT32_C(0xfffffff)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_SFT \
+ 0
+ /* The granularity of the value (bits or bytes). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE \
+ UINT32_C(0x10000000)
+ /* Value is in bits. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BITS \
+ (UINT32_C(0x0) << 28)
+ /* Value is in bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES \
+ (UINT32_C(0x1) << 28)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_LAST \
+ HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_SCALE_BYTES
+ /* bw_value_unit is 3 b */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MASK \
+ UINT32_C(0xe0000000)
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_SFT \
+ 29
+ /* Value is in Mb or MB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_MEGA \
+ (UINT32_C(0x0) << 29)
+ /* Value is in Kb or KB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_KILO \
+ (UINT32_C(0x2) << 29)
+ /* Value is in bits or bytes. */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_BASE \
+ (UINT32_C(0x4) << 29)
+ /* Value is in Gb or GB (base 10). */
+ #define HWRM_QUEUE_COS2BW_CFG_INPUT_QUEUE_ID0_MAX_BW_BW_VALUE_UNIT_GIGA \