+
+/**
+ * ixgbe_enter_lplu_x550em - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the
+ * X557 PHY immediately prior to entering LPLU.
+ **/
+s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
+{
+ u16 autoneg_status, an_10g_cntl_reg, autoneg_reg, speed;
+ s32 status;
+ ixgbe_link_speed lcd_speed;
+
+ /* If blocked by MNG FW, then don't restart AN */
+ if (ixgbe_check_reset_blocked(hw))
+ return IXGBE_SUCCESS;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = ixgbe_read_eeprom(hw, NVM_INIT_CTRL_3, &hw->eeprom.ctrl_word_3);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link is down, LPLU disabled in NVM, WoL disabled, or manageability
+ * disabled, then force link down by entering low power mode.
+ */
+ if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS) ||
+ !(hw->eeprom.ctrl_word_3 & NVM_INIT_CTRL_3_LPLU) ||
+ !(hw->wol_enabled || ixgbe_mng_present(hw)))
+ return ixgbe_set_copper_phy_power(hw, FALSE);
+
+ /* Determine LCD */
+ status = ixgbe_get_lcd_t_x550em(hw, &lcd_speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If no valid LCD link speed, then force link down and exit. */
+ if (lcd_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ return ixgbe_set_copper_phy_power(hw, FALSE);
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* clear everything but the speed bits */
+ speed &= IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK;
+
+ /* If current speed is already LCD, then exit. */
+ if (((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL)) ||
+ ((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL)))
+ return status;
+
+ /* Clear AN completed indication */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_10g_cntl_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Set AN advertizement to only include LCD */
+ if (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL) {
+ an_10g_cntl_reg &= ~IXGBE_MII_10GBASE_T_ADVERTISE;
+ autoneg_reg |= IXGBE_MII_1GBASE_T_ADVERTISE;
+ }
+
+ if (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL) {
+ an_10g_cntl_reg |= IXGBE_MII_10GBASE_T_ADVERTISE;
+ autoneg_reg &= ~IXGBE_MII_1GBASE_T_ADVERTISE;
+ }
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ an_10g_cntl_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.write_reg(hw,
+ IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Restart PHY auto-negotiation. */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ autoneg_reg |= IXGBE_MII_RESTART;
+
+ status = hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = ixgbe_setup_ixfi_x550em(hw, &lcd_speed);
+
+ return status;
+}
+
+/**
+ * ixgbe_get_lcd_x550em - Determine lowest common denominator
+ * @hw: pointer to hardware structure
+ * @lcd_speed: pointer to lowest common link speed
+ *
+ * Determine lowest common link speed with link partner.
+ **/
+s32 ixgbe_get_lcd_t_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *lcd_speed)
+{
+ u16 an_lp_status;
+ s32 status;
+ u16 word = hw->eeprom.ctrl_word_3;
+
+ *lcd_speed = IXGBE_LINK_SPEED_UNKNOWN;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_AUTO_NEG_LP_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_lp_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link partner advertised 1G, return 1G */
+ if (an_lp_status & IXGBE_AUTO_NEG_LP_1000BASE_CAP) {
+ *lcd_speed = IXGBE_LINK_SPEED_1GB_FULL;
+ return status;
+ }
+
+ /* If 10G disabled for LPLU via NVM D10GMP, then return no valid LCD */
+ if ((hw->bus.lan_id && (word & NVM_INIT_CTRL_3_D10GMP_PORT1)) ||
+ (word & NVM_INIT_CTRL_3_D10GMP_PORT0))
+ return status;
+
+ /* Link partner not capable of lower speeds, return 10G */
+ *lcd_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ return status;
+}
+
+/**
+ * ixgbe_setup_fc_X550em - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ **/
+s32 ixgbe_setup_fc_X550em(struct ixgbe_hw *hw)
+{
+ s32 ret_val = IXGBE_SUCCESS;
+ u32 pause, asm_dir, reg_val;
+
+ DEBUGFUNC("ixgbe_setup_fc_X550em");
+
+ /* Validate the requested mode */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /* 10gig parts do not have a word in the EEPROM to determine the
+ * default flow control setting, so we explicitly set it to full.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /* Determine PAUSE and ASM_DIR bits. */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ pause = 0;
+ asm_dir = 0;
+ break;
+ case ixgbe_fc_tx_pause:
+ pause = 0;
+ asm_dir = 1;
+ break;
+ case ixgbe_fc_rx_pause:
+ /* Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE, as such we fall
+ * through to the fc_full statement. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ case ixgbe_fc_full:
+ pause = 1;
+ asm_dir = 1;
+ break;
+ default:
+ ERROR_REPORT1(IXGBE_ERROR_ARGUMENT,
+ "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ }
+
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
+ ret_val = ixgbe_read_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (ret_val != IXGBE_SUCCESS)
+ goto out;
+ reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ if (pause)
+ reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
+ if (asm_dir)
+ reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ ret_val = ixgbe_write_iosf_sb_reg_x550(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ /* Not all devices fully support AN. */
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_X_KR)
+ hw->fc.disable_fc_autoneg = true;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_set_mux - Set mux for port 1 access with CS4227
+ * @hw: pointer to hardware structure
+ * @state: set mux if 1, clear if 0
+ */
+STATIC void ixgbe_set_mux(struct ixgbe_hw *hw, u8 state)
+{
+ u32 esdp;
+
+ if (!hw->bus.lan_id)
+ return;
+ esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
+ if (state)
+ esdp |= IXGBE_ESDP_SDP1;
+ else
+ esdp &= ~IXGBE_ESDP_SDP1;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
+ IXGBE_WRITE_FLUSH(hw);
+}
+
+/**
+ * ixgbe_acquire_swfw_sync_X550em - Acquire SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to acquire
+ *
+ * Acquires the SWFW semaphore and sets the I2C MUX
+ **/
+s32 ixgbe_acquire_swfw_sync_X550em(struct ixgbe_hw *hw, u32 mask)
+{
+ s32 status;
+
+ DEBUGFUNC("ixgbe_acquire_swfw_sync_X550em");
+
+ status = ixgbe_acquire_swfw_sync_X540(hw, mask);
+ if (status)
+ return status;
+
+ if (mask & IXGBE_GSSR_I2C_MASK)
+ ixgbe_set_mux(hw, 1);
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_release_swfw_sync_X550em - Release SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to release
+ *
+ * Releases the SWFW semaphore and sets the I2C MUX
+ **/
+void ixgbe_release_swfw_sync_X550em(struct ixgbe_hw *hw, u32 mask)
+{
+ DEBUGFUNC("ixgbe_release_swfw_sync_X550em");
+
+ if (mask & IXGBE_GSSR_I2C_MASK)
+ ixgbe_set_mux(hw, 0);
+
+ ixgbe_release_swfw_sync_X540(hw, mask);
+}