+
+/**
+ * ixgbe_enter_lplu_x550em - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the
+ * X557 PHY immediately prior to entering LPLU.
+ **/
+s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
+{
+ u16 an_10g_cntl_reg, autoneg_reg, speed;
+ s32 status;
+ ixgbe_link_speed lcd_speed;
+ u32 save_autoneg;
+ bool link_up;
+
+ /* SW LPLU not required on later HW revisions. */
+ if ((hw->mac.type == ixgbe_mac_X550EM_x) &&
+ (IXGBE_FUSES0_REV_MASK &
+ IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0))))
+ return IXGBE_SUCCESS;
+
+ /* If blocked by MNG FW, then don't restart AN */
+ if (ixgbe_check_reset_blocked(hw))
+ return IXGBE_SUCCESS;
+
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = ixgbe_read_eeprom(hw, NVM_INIT_CTRL_3, &hw->eeprom.ctrl_word_3);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link is down, LPLU disabled in NVM, WoL disabled, or manageability
+ * disabled, then force link down by entering low power mode.
+ */
+ if (!link_up || !(hw->eeprom.ctrl_word_3 & NVM_INIT_CTRL_3_LPLU) ||
+ !(hw->wol_enabled || ixgbe_mng_present(hw)))
+ return ixgbe_set_copper_phy_power(hw, FALSE);
+
+ /* Determine LCD */
+ status = ixgbe_get_lcd_t_x550em(hw, &lcd_speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If no valid LCD link speed, then force link down and exit. */
+ if (lcd_speed == IXGBE_LINK_SPEED_UNKNOWN)
+ return ixgbe_set_copper_phy_power(hw, FALSE);
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If no link now, speed is invalid so take link down */
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+ if (status != IXGBE_SUCCESS)
+ return ixgbe_set_copper_phy_power(hw, false);
+
+ /* clear everything but the speed bits */
+ speed &= IXGBE_MDIO_AUTO_NEG_VEN_STAT_SPEED_MASK;
+
+ /* If current speed is already LCD, then exit. */
+ if (((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_1GB_FULL)) ||
+ ((speed == IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB) &&
+ (lcd_speed == IXGBE_LINK_SPEED_10GB_FULL)))
+ return status;
+
+ /* Clear AN completed indication */
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_VENDOR_TX_ALARM,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_MII_10GBASE_T_AUTONEG_CTRL_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_10g_cntl_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MII_AUTONEG_VENDOR_PROVISION_1_REG,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ save_autoneg = hw->phy.autoneg_advertised;
+
+ /* Setup link at least common link speed */
+ status = hw->mac.ops.setup_link(hw, lcd_speed, false);
+
+ /* restore autoneg from before setting lplu speed */
+ hw->phy.autoneg_advertised = save_autoneg;
+
+ return status;
+}
+
+/**
+ * ixgbe_get_lcd_x550em - Determine lowest common denominator
+ * @hw: pointer to hardware structure
+ * @lcd_speed: pointer to lowest common link speed
+ *
+ * Determine lowest common link speed with link partner.
+ **/
+s32 ixgbe_get_lcd_t_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *lcd_speed)
+{
+ u16 an_lp_status;
+ s32 status;
+ u16 word = hw->eeprom.ctrl_word_3;
+
+ *lcd_speed = IXGBE_LINK_SPEED_UNKNOWN;
+
+ status = hw->phy.ops.read_reg(hw, IXGBE_AUTO_NEG_LP_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &an_lp_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link partner advertised 1G, return 1G */
+ if (an_lp_status & IXGBE_AUTO_NEG_LP_1000BASE_CAP) {
+ *lcd_speed = IXGBE_LINK_SPEED_1GB_FULL;
+ return status;
+ }
+
+ /* If 10G disabled for LPLU via NVM D10GMP, then return no valid LCD */
+ if ((hw->bus.lan_id && (word & NVM_INIT_CTRL_3_D10GMP_PORT1)) ||
+ (word & NVM_INIT_CTRL_3_D10GMP_PORT0))
+ return status;
+
+ /* Link partner not capable of lower speeds, return 10G */
+ *lcd_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ return status;
+}
+
+/**
+ * ixgbe_setup_fc_X550em - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ **/
+s32 ixgbe_setup_fc_X550em(struct ixgbe_hw *hw)
+{
+ s32 ret_val = IXGBE_SUCCESS;
+ u32 pause, asm_dir, reg_val;
+
+ DEBUGFUNC("ixgbe_setup_fc_X550em");
+
+ /* Validate the requested mode */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /* 10gig parts do not have a word in the EEPROM to determine the
+ * default flow control setting, so we explicitly set it to full.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /* Determine PAUSE and ASM_DIR bits. */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ pause = 0;
+ asm_dir = 0;
+ break;
+ case ixgbe_fc_tx_pause:
+ pause = 0;
+ asm_dir = 1;
+ break;
+ case ixgbe_fc_rx_pause:
+ /* Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE, as such we fall
+ * through to the fc_full statement. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ case ixgbe_fc_full:
+ pause = 1;
+ asm_dir = 1;
+ break;
+ default:
+ ERROR_REPORT1(IXGBE_ERROR_ARGUMENT,
+ "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ }
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X550EM_X_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR:
+ case IXGBE_DEV_ID_X550EM_A_KR_L:
+ ret_val = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (ret_val != IXGBE_SUCCESS)
+ goto out;
+ reg_val &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ if (pause)
+ reg_val |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
+ if (asm_dir)
+ reg_val |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ ret_val = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ /* This device does not fully support AN. */
+ hw->fc.disable_fc_autoneg = true;
+ break;
+ case IXGBE_DEV_ID_X550EM_X_XFI:
+ hw->fc.disable_fc_autoneg = true;
+ break;
+ default:
+ break;
+ }
+
+out:
+ return ret_val;
+}
+
+/**
+ * ixgbe_fc_autoneg_backplane_x550em_a - Enable flow control IEEE clause 37
+ * @hw: pointer to hardware structure
+ *
+ * Enable flow control according to IEEE clause 37.
+ **/
+void ixgbe_fc_autoneg_backplane_x550em_a(struct ixgbe_hw *hw)
+{
+ u32 link_s1, lp_an_page_low, an_cntl_1;
+ s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ ixgbe_link_speed speed;
+ bool link_up;
+
+ /* AN should have completed when the cable was plugged in.
+ * Look for reasons to bail out. Bail out if:
+ * - FC autoneg is disabled, or if
+ * - link is not up.
+ */
+ if (hw->fc.disable_fc_autoneg) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "Flow control autoneg is disabled");
+ goto out;
+ }
+
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ if (!link_up) {
+ ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down");
+ goto out;
+ }
+
+ /* Check at auto-negotiation has completed */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_S1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &link_s1);
+
+ if (status != IXGBE_SUCCESS ||
+ (link_s1 & IXGBE_KRM_LINK_S1_MAC_AN_COMPLETE) == 0) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ goto out;
+ }
+
+ /* Read the 10g AN autoc and LP ability registers and resolve
+ * local flow control settings accordingly
+ */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl_1);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ goto out;
+ }
+
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LP_BASE_PAGE_HIGH(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &lp_an_page_low);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ goto out;
+ }
+
+ status = ixgbe_negotiate_fc(hw, an_cntl_1, lp_an_page_low,
+ IXGBE_KRM_AN_CNTL_1_SYM_PAUSE,
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE,
+ IXGBE_KRM_LP_BASE_PAGE_HIGH_SYM_PAUSE,
+ IXGBE_KRM_LP_BASE_PAGE_HIGH_ASM_PAUSE);
+
+out:
+ if (status == IXGBE_SUCCESS) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
+}
+
+/**
+ * ixgbe_fc_autoneg_fiber_x550em_a - passthrough FC settings
+ * @hw: pointer to hardware structure
+ *
+ **/
+void ixgbe_fc_autoneg_fiber_x550em_a(struct ixgbe_hw *hw)
+{
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+}
+
+/**
+ * ixgbe_fc_autoneg_sgmii_x550em_a - Enable flow control IEEE clause 37
+ * @hw: pointer to hardware structure
+ *
+ * Enable flow control according to IEEE clause 37.
+ **/
+void ixgbe_fc_autoneg_sgmii_x550em_a(struct ixgbe_hw *hw)
+{
+ s32 status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ u32 info[FW_PHY_ACT_DATA_COUNT] = { 0 };
+ ixgbe_link_speed speed;
+ bool link_up;
+
+ /* AN should have completed when the cable was plugged in.
+ * Look for reasons to bail out. Bail out if:
+ * - FC autoneg is disabled, or if
+ * - link is not up.
+ */
+ if (hw->fc.disable_fc_autoneg) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "Flow control autoneg is disabled");
+ goto out;
+ }
+
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ if (!link_up) {
+ ERROR_REPORT1(IXGBE_ERROR_SOFTWARE, "The link is down");
+ goto out;
+ }
+
+ /* Check if auto-negotiation has completed */
+ status = ixgbe_fw_phy_activity(hw, FW_PHY_ACT_GET_LINK_INFO, &info);
+ if (status != IXGBE_SUCCESS ||
+ !(info[0] & FW_PHY_ACT_GET_LINK_INFO_AN_COMPLETE)) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ status = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ goto out;
+ }
+
+ /* Negotiate the flow control */
+ status = ixgbe_negotiate_fc(hw, info[0], info[0],
+ FW_PHY_ACT_GET_LINK_INFO_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_FC_TX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_RX,
+ FW_PHY_ACT_GET_LINK_INFO_LP_FC_TX);
+
+out:
+ if (status == IXGBE_SUCCESS) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
+}
+
+/**
+ * ixgbe_setup_fc_backplane_x550em_a - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ **/
+s32 ixgbe_setup_fc_backplane_x550em_a(struct ixgbe_hw *hw)
+{
+ s32 status = IXGBE_SUCCESS;
+ u32 an_cntl = 0;
+
+ DEBUGFUNC("ixgbe_setup_fc_backplane_x550em_a");
+
+ /* Validate the requested mode */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ ERROR_REPORT1(IXGBE_ERROR_UNSUPPORTED,
+ "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ return IXGBE_ERR_INVALID_LINK_SETTINGS;
+ }
+
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /* Set up the 1G and 10G flow control advertisement registers so the
+ * HW will be able to do FC autoneg once the cable is plugged in. If
+ * we link at 10G, the 1G advertisement is harmless and vice versa.
+ */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, &an_cntl);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Auto-Negotiation did not complete\n");
+ return status;
+ }
+
+ /* The possible values of fc.requested_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+ * other: Invalid.
+ */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ an_cntl &= ~(IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /* Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ an_cntl |= IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ an_cntl &= ~IXGBE_KRM_AN_CNTL_1_SYM_PAUSE;
+ break;
+ case ixgbe_fc_rx_pause:
+ /* Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE, as such we fall
+ * through to the fc_full statement. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ an_cntl |= IXGBE_KRM_AN_CNTL_1_SYM_PAUSE |
+ IXGBE_KRM_AN_CNTL_1_ASM_PAUSE;
+ break;
+ default:
+ ERROR_REPORT1(IXGBE_ERROR_ARGUMENT,
+ "Flow control param set incorrectly\n");
+ return IXGBE_ERR_CONFIG;
+ }
+
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, an_cntl);
+
+ /* Restart auto-negotiation. */
+ status = ixgbe_restart_an_internal_phy_x550em(hw);
+
+ return status;
+}
+
+/**
+ * ixgbe_set_mux - Set mux for port 1 access with CS4227
+ * @hw: pointer to hardware structure
+ * @state: set mux if 1, clear if 0
+ */
+STATIC void ixgbe_set_mux(struct ixgbe_hw *hw, u8 state)
+{
+ u32 esdp;
+
+ if (!hw->bus.lan_id)
+ return;
+ esdp = IXGBE_READ_REG(hw, IXGBE_ESDP);
+ if (state)
+ esdp |= IXGBE_ESDP_SDP1;
+ else
+ esdp &= ~IXGBE_ESDP_SDP1;
+ IXGBE_WRITE_REG(hw, IXGBE_ESDP, esdp);
+ IXGBE_WRITE_FLUSH(hw);
+}
+
+/**
+ * ixgbe_acquire_swfw_sync_X550em - Acquire SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to acquire
+ *
+ * Acquires the SWFW semaphore and sets the I2C MUX
+ **/
+s32 ixgbe_acquire_swfw_sync_X550em(struct ixgbe_hw *hw, u32 mask)
+{
+ s32 status;
+
+ DEBUGFUNC("ixgbe_acquire_swfw_sync_X550em");
+
+ status = ixgbe_acquire_swfw_sync_X540(hw, mask);
+ if (status)
+ return status;
+
+ if (mask & IXGBE_GSSR_I2C_MASK)
+ ixgbe_set_mux(hw, 1);
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_release_swfw_sync_X550em - Release SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to release
+ *
+ * Releases the SWFW semaphore and sets the I2C MUX
+ **/
+void ixgbe_release_swfw_sync_X550em(struct ixgbe_hw *hw, u32 mask)
+{
+ DEBUGFUNC("ixgbe_release_swfw_sync_X550em");
+
+ if (mask & IXGBE_GSSR_I2C_MASK)
+ ixgbe_set_mux(hw, 0);
+
+ ixgbe_release_swfw_sync_X540(hw, mask);
+}
+
+/**
+ * ixgbe_acquire_swfw_sync_X550a - Acquire SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to acquire
+ *
+ * Acquires the SWFW semaphore and get the shared phy token as needed
+ */
+STATIC s32 ixgbe_acquire_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask)
+{
+ u32 hmask = mask & ~IXGBE_GSSR_TOKEN_SM;
+ int retries = FW_PHY_TOKEN_RETRIES;
+ s32 status = IXGBE_SUCCESS;
+
+ DEBUGFUNC("ixgbe_acquire_swfw_sync_X550a");
+
+ while (--retries) {
+ status = IXGBE_SUCCESS;
+ if (hmask)
+ status = ixgbe_acquire_swfw_sync_X540(hw, hmask);
+ if (status) {
+ DEBUGOUT1("Could not acquire SWFW semaphore, Status = %d\n",
+ status);
+ return status;
+ }
+ if (!(mask & IXGBE_GSSR_TOKEN_SM))
+ return IXGBE_SUCCESS;
+
+ status = ixgbe_get_phy_token(hw);
+ if (status == IXGBE_ERR_TOKEN_RETRY)
+ DEBUGOUT1("Could not acquire PHY token, Status = %d\n",
+ status);
+
+ if (status == IXGBE_SUCCESS)
+ return IXGBE_SUCCESS;
+
+ if (hmask)
+ ixgbe_release_swfw_sync_X540(hw, hmask);
+
+ if (status != IXGBE_ERR_TOKEN_RETRY) {
+ DEBUGOUT1("Unable to retry acquiring the PHY token, Status = %d\n",
+ status);
+ return status;
+ }
+ }
+
+ DEBUGOUT1("Semaphore acquisition retries failed!: PHY ID = 0x%08X\n",
+ hw->phy.id);
+ return status;
+}
+
+/**
+ * ixgbe_release_swfw_sync_X550a - Release SWFW semaphore
+ * @hw: pointer to hardware structure
+ * @mask: Mask to specify which semaphore to release
+ *
+ * Releases the SWFW semaphore and puts the shared phy token as needed
+ */
+STATIC void ixgbe_release_swfw_sync_X550a(struct ixgbe_hw *hw, u32 mask)
+{
+ u32 hmask = mask & ~IXGBE_GSSR_TOKEN_SM;
+
+ DEBUGFUNC("ixgbe_release_swfw_sync_X550a");
+
+ if (mask & IXGBE_GSSR_TOKEN_SM)
+ ixgbe_put_phy_token(hw);
+
+ if (hmask)
+ ixgbe_release_swfw_sync_X540(hw, hmask);
+}
+
+/**
+ * ixgbe_read_phy_reg_x550a - Reads specified PHY register
+ * @hw: pointer to hardware structure
+ * @reg_addr: 32 bit address of PHY register to read
+ * @device_type: 5 bit device type
+ * @phy_data: Pointer to read data from PHY register
+ *
+ * Reads a value from a specified PHY register using the SWFW lock and PHY
+ * Token. The PHY Token is needed since the MDIO is shared between to MAC
+ * instances.
+ **/
+s32 ixgbe_read_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
+ u32 device_type, u16 *phy_data)
+{
+ s32 status;
+ u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
+
+ DEBUGFUNC("ixgbe_read_phy_reg_x550a");
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, mask))
+ return IXGBE_ERR_SWFW_SYNC;
+
+ status = hw->phy.ops.read_reg_mdi(hw, reg_addr, device_type, phy_data);
+
+ hw->mac.ops.release_swfw_sync(hw, mask);
+
+ return status;
+}
+
+/**
+ * ixgbe_write_phy_reg_x550a - Writes specified PHY register
+ * @hw: pointer to hardware structure
+ * @reg_addr: 32 bit PHY register to write
+ * @device_type: 5 bit device type
+ * @phy_data: Data to write to the PHY register
+ *
+ * Writes a value to specified PHY register using the SWFW lock and PHY Token.
+ * The PHY Token is needed since the MDIO is shared between to MAC instances.
+ **/
+s32 ixgbe_write_phy_reg_x550a(struct ixgbe_hw *hw, u32 reg_addr,
+ u32 device_type, u16 phy_data)
+{
+ s32 status;
+ u32 mask = hw->phy.phy_semaphore_mask | IXGBE_GSSR_TOKEN_SM;
+
+ DEBUGFUNC("ixgbe_write_phy_reg_x550a");
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, mask) == IXGBE_SUCCESS) {
+ status = hw->phy.ops.write_reg_mdi(hw, reg_addr, device_type,
+ phy_data);
+ hw->mac.ops.release_swfw_sync(hw, mask);
+ } else {
+ status = IXGBE_ERR_SWFW_SYNC;
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_handle_lasi_ext_t_x550em - Handle external Base T PHY interrupt
+ * @hw: pointer to hardware structure
+ *
+ * Handle external Base T PHY interrupt. If high temperature
+ * failure alarm then return error, else if link status change
+ * then setup internal/external PHY link
+ *
+ * Return IXGBE_ERR_OVERTEMP if interrupt is high temperature
+ * failure alarm, else return PHY access status.
+ */
+s32 ixgbe_handle_lasi_ext_t_x550em(struct ixgbe_hw *hw)
+{
+ bool lsc;
+ u32 status;
+
+ status = ixgbe_get_lasi_ext_t_x550em(hw, &lsc);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ if (lsc)
+ return ixgbe_setup_internal_phy(hw);
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_setup_mac_link_t_X550em - Sets the auto advertised link speed
+ * @hw: pointer to hardware structure
+ * @speed: new link speed
+ * @autoneg_wait_to_complete: true when waiting for completion is needed
+ *
+ * Setup internal/external PHY link speed based on link speed, then set
+ * external PHY auto advertised link speed.
+ *
+ * Returns error status for any failure
+ **/
+s32 ixgbe_setup_mac_link_t_X550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ s32 status;
+ ixgbe_link_speed force_speed;
+
+ DEBUGFUNC("ixgbe_setup_mac_link_t_X550em");
+
+ /* Setup internal/external PHY link speed to iXFI (10G), unless
+ * only 1G is auto advertised then setup KX link.
+ */
+ if (speed & IXGBE_LINK_SPEED_10GB_FULL)
+ force_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ else
+ force_speed = IXGBE_LINK_SPEED_1GB_FULL;
+
+ /* If X552 and internal link mode is XFI, then setup XFI internal link.
+ */
+ if (hw->mac.type == ixgbe_mac_X550EM_x &&
+ !(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ status = ixgbe_setup_ixfi_x550em(hw, &force_speed);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+ }
+
+ return hw->phy.ops.setup_link_speed(hw, speed, autoneg_wait_to_complete);
+}
+
+/**
+ * ixgbe_check_link_t_X550em - Determine link and speed status
+ * @hw: pointer to hardware structure
+ * @speed: pointer to link speed
+ * @link_up: true when link is up
+ * @link_up_wait_to_complete: bool used to wait for link up or not
+ *
+ * Check that both the MAC and X557 external PHY have link.
+ **/
+s32 ixgbe_check_link_t_X550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed,
+ bool *link_up, bool link_up_wait_to_complete)
+{
+ u32 status;
+ u16 i, autoneg_status = 0;
+
+ if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
+ return IXGBE_ERR_CONFIG;
+
+ status = ixgbe_check_mac_link_generic(hw, speed, link_up,
+ link_up_wait_to_complete);
+
+ /* If check link fails or MAC link is not up, then return */
+ if (status != IXGBE_SUCCESS || !(*link_up))
+ return status;
+
+ /* MAC link is up, so check external PHY link.
+ * X557 PHY. Link status is latching low, and can only be used to detect
+ * link drop, and not the current status of the link without performing
+ * back-to-back reads.
+ */
+ for (i = 0; i < 2; i++) {
+ status = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+ }
+
+ /* If external PHY link is not up, then indicate link not up */
+ if (!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS))
+ *link_up = false;
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_reset_phy_t_X550em - Performs X557 PHY reset and enables LASI
+ * @hw: pointer to hardware structure
+ **/
+s32 ixgbe_reset_phy_t_X550em(struct ixgbe_hw *hw)
+{
+ s32 status;
+
+ status = ixgbe_reset_phy_generic(hw);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Configure Link Status Alarm and Temperature Threshold interrupts */
+ return ixgbe_enable_lasi_ext_t_x550em(hw);
+}
+
+/**
+ * ixgbe_led_on_t_X550em - Turns on the software controllable LEDs.
+ * @hw: pointer to hardware structure
+ * @led_idx: led number to turn on
+ **/
+s32 ixgbe_led_on_t_X550em(struct ixgbe_hw *hw, u32 led_idx)
+{
+ u16 phy_data;
+
+ DEBUGFUNC("ixgbe_led_on_t_X550em");
+
+ if (led_idx >= IXGBE_X557_MAX_LED_INDEX)
+ return IXGBE_ERR_PARAM;
+
+ /* To turn on the LED, set mode to ON. */
+ ixgbe_read_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, &phy_data);
+ phy_data |= IXGBE_X557_LED_MANUAL_SET_MASK;
+ ixgbe_write_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, phy_data);
+
+ /* Some designs have the LEDs wired to the MAC */
+ return ixgbe_led_on_generic(hw, led_idx);
+}
+
+/**
+ * ixgbe_led_off_t_X550em - Turns off the software controllable LEDs.
+ * @hw: pointer to hardware structure
+ * @led_idx: led number to turn off
+ **/
+s32 ixgbe_led_off_t_X550em(struct ixgbe_hw *hw, u32 led_idx)
+{
+ u16 phy_data;
+
+ DEBUGFUNC("ixgbe_led_off_t_X550em");
+
+ if (led_idx >= IXGBE_X557_MAX_LED_INDEX)
+ return IXGBE_ERR_PARAM;
+
+ /* To turn on the LED, set mode to ON. */
+ ixgbe_read_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, &phy_data);
+ phy_data &= ~IXGBE_X557_LED_MANUAL_SET_MASK;
+ ixgbe_write_phy_reg(hw, IXGBE_X557_LED_PROVISIONING + led_idx,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE, phy_data);
+
+ /* Some designs have the LEDs wired to the MAC */
+ return ixgbe_led_off_generic(hw, led_idx);
+}
+
+/**
+ * ixgbe_set_fw_drv_ver_x550 - Sends driver version to firmware
+ * @hw: pointer to the HW structure
+ * @maj: driver version major number
+ * @min: driver version minor number
+ * @build: driver version build number
+ * @sub: driver version sub build number
+ * @len: length of driver_ver string
+ * @driver_ver: driver string
+ *
+ * Sends driver version number to firmware through the manageability
+ * block. On success return IXGBE_SUCCESS
+ * else returns IXGBE_ERR_SWFW_SYNC when encountering an error acquiring
+ * semaphore or IXGBE_ERR_HOST_INTERFACE_COMMAND when command fails.
+ **/
+s32 ixgbe_set_fw_drv_ver_x550(struct ixgbe_hw *hw, u8 maj, u8 min,
+ u8 build, u8 sub, u16 len, const char *driver_ver)
+{
+ struct ixgbe_hic_drv_info2 fw_cmd;
+ s32 ret_val = IXGBE_SUCCESS;
+ int i;
+
+ DEBUGFUNC("ixgbe_set_fw_drv_ver_x550");
+
+ if ((len == 0) || (driver_ver == NULL) ||
+ (len > sizeof(fw_cmd.driver_string)))
+ return IXGBE_ERR_INVALID_ARGUMENT;
+
+ fw_cmd.hdr.cmd = FW_CEM_CMD_DRIVER_INFO;
+ fw_cmd.hdr.buf_len = FW_CEM_CMD_DRIVER_INFO_LEN + len;
+ fw_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
+ fw_cmd.port_num = (u8)hw->bus.func;
+ fw_cmd.ver_maj = maj;
+ fw_cmd.ver_min = min;
+ fw_cmd.ver_build = build;
+ fw_cmd.ver_sub = sub;
+ fw_cmd.hdr.checksum = 0;
+ memcpy(fw_cmd.driver_string, driver_ver, len);
+ fw_cmd.hdr.checksum = ixgbe_calculate_checksum((u8 *)&fw_cmd,
+ (FW_CEM_HDR_LEN + fw_cmd.hdr.buf_len));
+
+ for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
+ ret_val = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd,
+ sizeof(fw_cmd),
+ IXGBE_HI_COMMAND_TIMEOUT,
+ true);
+ if (ret_val != IXGBE_SUCCESS)
+ continue;
+
+ if (fw_cmd.hdr.cmd_or_resp.ret_status ==
+ FW_CEM_RESP_STATUS_SUCCESS)
+ ret_val = IXGBE_SUCCESS;
+ else
+ ret_val = IXGBE_ERR_HOST_INTERFACE_COMMAND;
+
+ break;
+ }
+
+ return ret_val;
+}
+
+/**
+ * ixgbe_fw_recovery_mode_X550 - Check FW NVM recovery mode
+ * @hw: pointer t hardware structure
+ *
+ * Returns true if in FW NVM recovery mode.
+ **/
+bool ixgbe_fw_recovery_mode_X550(struct ixgbe_hw *hw)
+{
+ u32 fwsm;
+
+ fwsm = IXGBE_READ_REG(hw, IXGBE_FWSM_BY_MAC(hw));
+
+ return !!(fwsm & IXGBE_FWSM_FW_NVM_RECOVERY_MODE);
+}