+
+ /* Reset PHY */
+ if (!hw->phy.reset_disable && hw->phy.ops.reset)
+ hw->phy.ops.reset(hw);
+
+mac_reset_top:
+ /* Issue global reset to the MAC. Needs to be SW reset if link is up.
+ * If link reset is used when link is up, it might reset the PHY when
+ * mng is using it. If link is down or the flag to force full link
+ * reset is set, then perform link reset.
+ */
+ ctrl = IXGBE_CTRL_LNK_RST;
+ if (!hw->force_full_reset) {
+ hw->mac.ops.check_link(hw, &link_speed, &link_up, false);
+ if (link_up)
+ ctrl = IXGBE_CTRL_RST;
+ }
+
+ ctrl |= IXGBE_READ_REG(hw, IXGBE_CTRL);
+ IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl);
+ IXGBE_WRITE_FLUSH(hw);
+
+ /* Poll for reset bit to self-clear meaning reset is complete */
+ for (i = 0; i < 10; i++) {
+ usec_delay(1);
+ ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL);
+ if (!(ctrl & IXGBE_CTRL_RST_MASK))
+ break;
+ }
+
+ if (ctrl & IXGBE_CTRL_RST_MASK) {
+ status = IXGBE_ERR_RESET_FAILED;
+ DEBUGOUT("Reset polling failed to complete.\n");
+ }
+
+ msec_delay(50);
+
+ /* Double resets are required for recovery from certain error
+ * conditions. Between resets, it is necessary to stall to
+ * allow time for any pending HW events to complete.
+ */
+ if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) {
+ hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED;
+ goto mac_reset_top;
+ }
+
+ /* Store the permanent mac address */
+ hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr);
+
+ /* Store MAC address from RAR0, clear receive address registers, and
+ * clear the multicast table. Also reset num_rar_entries to 128,
+ * since we modify this value when programming the SAN MAC address.
+ */
+ hw->mac.num_rar_entries = 128;
+ hw->mac.ops.init_rx_addrs(hw);
+
+ ixgbe_set_mdio_speed(hw);
+
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_X_SFP)
+ ixgbe_setup_mux_ctl(hw);
+
+ return status;
+}
+
+/**
+ * ixgbe_init_ext_t_x550em - Start (unstall) the external Base T PHY.
+ * @hw: pointer to hardware structure
+ */
+s32 ixgbe_init_ext_t_x550em(struct ixgbe_hw *hw)
+{
+ u32 status;
+ u16 reg;
+
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_TX_VENDOR_ALARMS_3,
+ IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ ®);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If PHY FW reset completed bit is set then this is the first
+ * SW instance after a power on so the PHY FW must be un-stalled.
+ */
+ if (reg & IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK) {
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_GLOBAL_RES_PR_10,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ reg &= ~IXGBE_MDIO_POWER_UP_STALL;
+
+ status = hw->phy.ops.write_reg(hw,
+ IXGBE_MDIO_GLOBAL_RES_PR_10,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+
+ if (status != IXGBE_SUCCESS)
+ return status;
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_setup_kr_x550em - Configure the KR PHY.
+ * @hw: pointer to hardware structure
+ *
+ * Configures the integrated KR PHY for X550EM_x.
+ **/
+s32 ixgbe_setup_kr_x550em(struct ixgbe_hw *hw)
+{
+ if (hw->mac.type != ixgbe_mac_X550EM_x)
+ return IXGBE_SUCCESS;
+
+ return ixgbe_setup_kr_speed_x550em(hw, hw->phy.autoneg_advertised);
+}
+
+/**
+ * ixgbe_setup_mac_link_sfp_x550em - Setup internal/external the PHY for SFP
+ * @hw: pointer to hardware structure
+ *
+ * Configure the external PHY and the integrated KR PHY for SFP support.
+ **/
+s32 ixgbe_setup_mac_link_sfp_x550em(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ s32 ret_val;
+ u16 reg_slice, reg_val;
+ bool setup_linear = false;
+ UNREFERENCED_1PARAMETER(autoneg_wait_to_complete);
+
+ /* Check if SFP module is supported and linear */
+ ret_val = ixgbe_supported_sfp_modules_X550em(hw, &setup_linear);
+
+ /* If no SFP module present, then return success. Return success since
+ * there is no reason to configure CS4227 and SFP not present error is
+ * not excepted in the setup MAC link flow.
+ */
+ if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT)
+ return IXGBE_SUCCESS;
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ /* Configure internal PHY for KR/KX. */
+ ixgbe_setup_kr_speed_x550em(hw, speed);
+
+ /* Configure CS4227 LINE side to proper mode. */
+ reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB +
+ (hw->bus.lan_id << 12);
+ if (setup_linear)
+ reg_val = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
+ else
+ reg_val = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
+ ret_val = hw->link.ops.write_link(hw, hw->link.addr, reg_slice,
+ reg_val);
+ return ret_val;
+}
+
+/**
+ * ixgbe_setup_mac_link_sfp_x550a - Setup internal PHY for SFP
+ * @hw: pointer to hardware structure
+ *
+ * Configure the the integrated PHY for SFP support.
+ **/
+s32 ixgbe_setup_mac_link_sfp_x550a(struct ixgbe_hw *hw,
+ ixgbe_link_speed speed,
+ bool autoneg_wait_to_complete)
+{
+ s32 ret_val;
+ u16 reg_phy_ext;
+ bool setup_linear = false;
+ u32 reg_slice, reg_phy_int, slice_offset;
+
+ UNREFERENCED_1PARAMETER(autoneg_wait_to_complete);
+
+ /* Check if SFP module is supported and linear */
+ ret_val = ixgbe_supported_sfp_modules_X550em(hw, &setup_linear);
+
+ /* If no SFP module present, then return success. Return success since
+ * SFP not present error is not excepted in the setup MAC link flow.
+ */
+ if (ret_val == IXGBE_ERR_SFP_NOT_PRESENT)
+ return IXGBE_SUCCESS;
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_SFP_N) {
+ /* Configure internal PHY for native SFI */
+ ret_val = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_8(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_phy_int);
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ if (setup_linear) {
+ reg_phy_int &= ~IXGBE_KRM_AN_CNTL_8_LIMITING;
+ reg_phy_int |= IXGBE_KRM_AN_CNTL_8_LINEAR;
+ } else {
+ reg_phy_int |= IXGBE_KRM_AN_CNTL_8_LIMITING;
+ reg_phy_int &= ~IXGBE_KRM_AN_CNTL_8_LINEAR;
+ }
+
+ ret_val = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_AN_CNTL_8(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_phy_int);
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ /* Setup XFI/SFI internal link. */
+ ret_val = ixgbe_setup_ixfi_x550em(hw, &speed);
+ } else {
+ /* Configure internal PHY for KR/KX. */
+ ixgbe_setup_kr_speed_x550em(hw, speed);
+
+ if (hw->phy.addr == 0x0 || hw->phy.addr == 0xFFFF) {
+ /* Find Address */
+ DEBUGOUT("Invalid NW_MNG_IF_SEL.MDIO_PHY_ADD value\n");
+ return IXGBE_ERR_PHY_ADDR_INVALID;
+ }
+
+ /* Get external PHY device id */
+ ret_val = hw->phy.ops.read_reg(hw, IXGBE_CS4227_GLOBAL_ID_MSB,
+ IXGBE_MDIO_ZERO_DEV_TYPE, ®_phy_ext);
+
+ if (ret_val != IXGBE_SUCCESS)
+ return ret_val;
+
+ /* When configuring quad port CS4223, the MAC instance is part
+ * of the slice offset.
+ */
+ if (reg_phy_ext == IXGBE_CS4223_PHY_ID)
+ slice_offset = (hw->bus.lan_id +
+ (hw->bus.instance_id << 1)) << 12;
+ else
+ slice_offset = hw->bus.lan_id << 12;
+
+ /* Configure CS4227/CS4223 LINE side to proper mode. */
+ reg_slice = IXGBE_CS4227_LINE_SPARE24_LSB + slice_offset;
+ if (setup_linear)
+ reg_phy_ext = (IXGBE_CS4227_EDC_MODE_CX1 << 1) | 0x1;
+ else
+ reg_phy_ext = (IXGBE_CS4227_EDC_MODE_SR << 1) | 0x1;
+ ret_val = hw->phy.ops.write_reg(hw, reg_slice,
+ IXGBE_MDIO_ZERO_DEV_TYPE, reg_phy_ext);
+ }
+ return ret_val;
+}
+
+/**
+ * ixgbe_setup_ixfi_x550em_x - MAC specific iXFI configuration
+ * @hw: pointer to hardware structure
+ *
+ * iXfI configuration needed for ixgbe_mac_X550EM_x devices.
+ **/
+STATIC s32 ixgbe_setup_ixfi_x550em_x(struct ixgbe_hw *hw)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ s32 status;
+ u32 reg_val;
+
+ /* Disable training protocol FSM. */
+ status = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_CONV_WO_PROTOCOL;
+ status = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Disable Flex from training TXFFE. */
+ status = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_DSP_TXFFE_STATE_4(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_C0_EN;
+ reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CP1_CN1_EN;
+ reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CO_ADAPT_EN;
+ status = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_DSP_TXFFE_STATE_4(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ status = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_DSP_TXFFE_STATE_5(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_C0_EN;
+ reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CP1_CN1_EN;
+ reg_val &= ~IXGBE_KRM_DSP_TXFFE_STATE_CO_ADAPT_EN;
+ status = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_DSP_TXFFE_STATE_5(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Enable override for coefficients. */
+ status = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_OVRRD_EN;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CZERO_EN;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CPLUS1_OVRRD_EN;
+ reg_val |= IXGBE_KRM_TX_COEFF_CTRL_1_CMINUS1_OVRRD_EN;
+ status = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ return status;
+}
+
+/**
+ * ixgbe_setup_ixfi_x550em - Configure the KR PHY for iXFI mode.
+ * @hw: pointer to hardware structure
+ * @speed: the link speed to force
+ *
+ * Configures the integrated KR PHY to use iXFI mode. Used to connect an
+ * internal and external PHY at a specific speed, without autonegotiation.
+ **/
+STATIC s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed)
+{
+ struct ixgbe_mac_info *mac = &hw->mac;
+ s32 status;
+ u32 reg_val;
+
+ /* Disable AN and force speed to 10G Serial. */
+ status = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+ reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
+
+ /* Select forced link speed for internal PHY. */
+ switch (*speed) {
+ case IXGBE_LINK_SPEED_10GB_FULL:
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G;
+ break;
+ case IXGBE_LINK_SPEED_1GB_FULL:
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G;
+ break;
+ default:
+ /* Other link speeds are not supported by internal KR PHY. */
+ return IXGBE_ERR_LINK_SETUP;
+ }
+
+ status = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Additional configuration needed for x550em_x */
+ if (hw->mac.type == ixgbe_mac_X550EM_x) {
+ status = ixgbe_setup_ixfi_x550em_x(hw);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ }
+
+ /* Toggle port SW reset by AN reset. */
+ status = mac->ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_AN_RESTART;
+ status = mac->ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ return status;
+}
+
+/**
+ * ixgbe_ext_phy_t_x550em_get_link - Get ext phy link status
+ * @hw: address of hardware structure
+ * @link_up: address of boolean to indicate link status
+ *
+ * Returns error code if unable to get link status.
+ */
+STATIC s32 ixgbe_ext_phy_t_x550em_get_link(struct ixgbe_hw *hw, bool *link_up)
+{
+ u32 ret;
+ u16 autoneg_status;
+
+ *link_up = false;
+
+ /* read this twice back to back to indicate current status */
+ ret = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+ if (ret != IXGBE_SUCCESS)
+ return ret;
+
+ ret = hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &autoneg_status);
+ if (ret != IXGBE_SUCCESS)
+ return ret;
+
+ *link_up = !!(autoneg_status & IXGBE_MDIO_AUTO_NEG_LINK_STATUS);
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_setup_internal_phy_t_x550em - Configure KR PHY to X557 link
+ * @hw: point to hardware structure
+ *
+ * Configures the link between the integrated KR PHY and the external X557 PHY
+ * The driver will call this function when it gets a link status change
+ * interrupt from the X557 PHY. This function configures the link speed
+ * between the PHYs to match the link speed of the BASE-T link.
+ *
+ * A return of a non-zero value indicates an error, and the base driver should
+ * not report link up.
+ */
+s32 ixgbe_setup_internal_phy_t_x550em(struct ixgbe_hw *hw)
+{
+ ixgbe_link_speed force_speed;
+ bool link_up;
+ u32 status;
+ u16 speed;
+
+ if (hw->mac.ops.get_media_type(hw) != ixgbe_media_type_copper)
+ return IXGBE_ERR_CONFIG;
+
+ if (!(hw->phy.nw_mng_if_sel & IXGBE_NW_MNG_IF_SEL_INT_PHY_MODE)) {
+ /* If link is down, there is no setup necessary so return */
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ if (!link_up)
+ return IXGBE_SUCCESS;
+
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_AUTO_NEG_VENDOR_STAT,
+ IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
+ &speed);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* If link is still down - no setup is required so return */
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ if (!link_up)
+ return IXGBE_SUCCESS;
+
+ /* clear everything but the speed and duplex bits */
+ speed &= IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_MASK;
+
+ switch (speed) {
+ case IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_10GB_FULL:
+ force_speed = IXGBE_LINK_SPEED_10GB_FULL;
+ break;
+ case IXGBE_MDIO_AUTO_NEG_VENDOR_STATUS_1GB_FULL:
+ force_speed = IXGBE_LINK_SPEED_1GB_FULL;
+ break;
+ default:
+ /* Internal PHY does not support anything else */
+ return IXGBE_ERR_INVALID_LINK_SETTINGS;
+ }
+
+ return ixgbe_setup_ixfi_x550em(hw, &force_speed);
+ } else {
+ speed = IXGBE_LINK_SPEED_10GB_FULL |
+ IXGBE_LINK_SPEED_1GB_FULL;
+ return ixgbe_setup_kr_speed_x550em(hw, speed);
+ }
+}
+
+/**
+ * ixgbe_setup_phy_loopback_x550em - Configure the KR PHY for loopback.
+ * @hw: pointer to hardware structure
+ *
+ * Configures the integrated KR PHY to use internal loopback mode.
+ **/
+s32 ixgbe_setup_phy_loopback_x550em(struct ixgbe_hw *hw)
+{
+ s32 status;
+ u32 reg_val;
+
+ /* Disable AN and force speed to 10G Serial. */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+ reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
+ reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G;
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Set near-end loopback clocks. */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_32B;
+ reg_val |= IXGBE_KRM_PORT_CAR_GEN_CTRL_NELB_KRPCS;
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_PORT_CAR_GEN_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Set loopback enable. */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val |= IXGBE_KRM_PMD_DFX_BURNIN_TX_RX_KR_LB_MASK;
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_PMD_DFX_BURNIN(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+
+ /* Training bypass. */
+ status = hw->mac.ops.read_iosf_sb_reg(hw,
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, ®_val);
+ if (status != IXGBE_SUCCESS)
+ return status;
+ reg_val |= IXGBE_KRM_RX_TRN_LINKUP_CTRL_PROTOCOL_BYPASS;
+ status = hw->mac.ops.write_iosf_sb_reg(hw,
+ IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
+ IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+
+ return status;
+}
+
+/**
+ * ixgbe_read_ee_hostif_X550 - Read EEPROM word using a host interface command
+ * assuming that the semaphore is already obtained.
+ * @hw: pointer to hardware structure
+ * @offset: offset of word in the EEPROM to read
+ * @data: word read from the EEPROM
+ *
+ * Reads a 16 bit word from the EEPROM using the hostif.
+ **/
+s32 ixgbe_read_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
+ u16 *data)
+{
+ s32 status;
+ struct ixgbe_hic_read_shadow_ram buffer;
+
+ DEBUGFUNC("ixgbe_read_ee_hostif_data_X550");
+ buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
+ buffer.hdr.req.buf_lenh = 0;
+ buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
+ buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+ /* convert offset from words to bytes */
+ buffer.address = IXGBE_CPU_TO_BE32(offset * 2);
+ /* one word */
+ buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16));
+
+ status = ixgbe_host_interface_command(hw, (u32 *)&buffer,
+ sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT, false);
+
+ if (status)
+ return status;
+
+ *data = (u16)IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG,
+ FW_NVM_DATA_OFFSET);
+
+ return 0;
+}
+
+/**
+ * ixgbe_read_ee_hostif_X550 - Read EEPROM word using a host interface command
+ * @hw: pointer to hardware structure
+ * @offset: offset of word in the EEPROM to read
+ * @data: word read from the EEPROM
+ *
+ * Reads a 16 bit word from the EEPROM using the hostif.
+ **/
+s32 ixgbe_read_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset,
+ u16 *data)
+{
+ s32 status = IXGBE_SUCCESS;
+
+ DEBUGFUNC("ixgbe_read_ee_hostif_X550");
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) ==
+ IXGBE_SUCCESS) {
+ status = ixgbe_read_ee_hostif_data_X550(hw, offset, data);
+ hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ } else {
+ status = IXGBE_ERR_SWFW_SYNC;
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_read_ee_hostif_buffer_X550- Read EEPROM word(s) using hostif
+ * @hw: pointer to hardware structure
+ * @offset: offset of word in the EEPROM to read
+ * @words: number of words
+ * @data: word(s) read from the EEPROM
+ *
+ * Reads a 16 bit word(s) from the EEPROM using the hostif.
+ **/
+s32 ixgbe_read_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
+ u16 offset, u16 words, u16 *data)
+{
+ struct ixgbe_hic_read_shadow_ram buffer;
+ u32 current_word = 0;
+ u16 words_to_read;
+ s32 status;
+ u32 i;
+
+ DEBUGFUNC("ixgbe_read_ee_hostif_buffer_X550");
+
+ /* Take semaphore for the entire operation. */
+ status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ if (status) {
+ DEBUGOUT("EEPROM read buffer - semaphore failed\n");
+ return status;
+ }
+ while (words) {
+ if (words > FW_MAX_READ_BUFFER_SIZE / 2)
+ words_to_read = FW_MAX_READ_BUFFER_SIZE / 2;
+ else
+ words_to_read = words;
+
+ buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
+ buffer.hdr.req.buf_lenh = 0;
+ buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
+ buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+ /* convert offset from words to bytes */
+ buffer.address = IXGBE_CPU_TO_BE32((offset + current_word) * 2);
+ buffer.length = IXGBE_CPU_TO_BE16(words_to_read * 2);
+
+ status = ixgbe_host_interface_command(hw, (u32 *)&buffer,
+ sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT,
+ false);
+
+ if (status) {
+ DEBUGOUT("Host interface command failed\n");
+ goto out;
+ }
+
+ for (i = 0; i < words_to_read; i++) {
+ u32 reg = IXGBE_FLEX_MNG + (FW_NVM_DATA_OFFSET << 2) +
+ 2 * i;
+ u32 value = IXGBE_READ_REG(hw, reg);
+
+ data[current_word] = (u16)(value & 0xffff);
+ current_word++;
+ i++;
+ if (i < words_to_read) {
+ value >>= 16;
+ data[current_word] = (u16)(value & 0xffff);
+ current_word++;
+ }
+ }
+ words -= words_to_read;
+ }
+
+out:
+ hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ return status;
+}
+
+/**
+ * ixgbe_write_ee_hostif_X550 - Write EEPROM word using hostif
+ * @hw: pointer to hardware structure
+ * @offset: offset of word in the EEPROM to write
+ * @data: word write to the EEPROM
+ *
+ * Write a 16 bit word to the EEPROM using the hostif.
+ **/
+s32 ixgbe_write_ee_hostif_data_X550(struct ixgbe_hw *hw, u16 offset,
+ u16 data)
+{
+ s32 status;
+ struct ixgbe_hic_write_shadow_ram buffer;
+
+ DEBUGFUNC("ixgbe_write_ee_hostif_data_X550");
+
+ buffer.hdr.req.cmd = FW_WRITE_SHADOW_RAM_CMD;
+ buffer.hdr.req.buf_lenh = 0;
+ buffer.hdr.req.buf_lenl = FW_WRITE_SHADOW_RAM_LEN;
+ buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+ /* one word */
+ buffer.length = IXGBE_CPU_TO_BE16(sizeof(u16));
+ buffer.data = data;
+ buffer.address = IXGBE_CPU_TO_BE32(offset * 2);
+
+ status = ixgbe_host_interface_command(hw, (u32 *)&buffer,
+ sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT, false);
+
+ return status;
+}
+
+/**
+ * ixgbe_write_ee_hostif_X550 - Write EEPROM word using hostif
+ * @hw: pointer to hardware structure
+ * @offset: offset of word in the EEPROM to write
+ * @data: word write to the EEPROM
+ *
+ * Write a 16 bit word to the EEPROM using the hostif.
+ **/
+s32 ixgbe_write_ee_hostif_X550(struct ixgbe_hw *hw, u16 offset,
+ u16 data)
+{
+ s32 status = IXGBE_SUCCESS;
+
+ DEBUGFUNC("ixgbe_write_ee_hostif_X550");
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM) ==
+ IXGBE_SUCCESS) {
+ status = ixgbe_write_ee_hostif_data_X550(hw, offset, data);
+ hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ } else {
+ DEBUGOUT("write ee hostif failed to get semaphore");
+ status = IXGBE_ERR_SWFW_SYNC;
+ }
+
+ return status;
+}
+
+/**
+ * ixgbe_write_ee_hostif_buffer_X550 - Write EEPROM word(s) using hostif
+ * @hw: pointer to hardware structure
+ * @offset: offset of word in the EEPROM to write
+ * @words: number of words
+ * @data: word(s) write to the EEPROM
+ *
+ * Write a 16 bit word(s) to the EEPROM using the hostif.
+ **/
+s32 ixgbe_write_ee_hostif_buffer_X550(struct ixgbe_hw *hw,
+ u16 offset, u16 words, u16 *data)
+{
+ s32 status = IXGBE_SUCCESS;
+ u32 i = 0;
+
+ DEBUGFUNC("ixgbe_write_ee_hostif_buffer_X550");
+
+ /* Take semaphore for the entire operation. */
+ status = hw->mac.ops.acquire_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("EEPROM write buffer - semaphore failed\n");
+ goto out;
+ }
+
+ for (i = 0; i < words; i++) {
+ status = ixgbe_write_ee_hostif_data_X550(hw, offset + i,
+ data[i]);
+
+ if (status != IXGBE_SUCCESS) {
+ DEBUGOUT("Eeprom buffered write failed\n");
+ break;
+ }
+ }
+
+ hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_EEP_SM);
+out:
+
+ return status;
+}
+
+/**
+ * ixgbe_checksum_ptr_x550 - Checksum one pointer region
+ * @hw: pointer to hardware structure
+ * @ptr: pointer offset in eeprom
+ * @size: size of section pointed by ptr, if 0 first word will be used as size
+ * @csum: address of checksum to update
+ *
+ * Returns error status for any failure
+ */
+STATIC s32 ixgbe_checksum_ptr_x550(struct ixgbe_hw *hw, u16 ptr,
+ u16 size, u16 *csum, u16 *buffer,
+ u32 buffer_size)
+{
+ u16 buf[256];
+ s32 status;
+ u16 length, bufsz, i, start;
+ u16 *local_buffer;
+
+ bufsz = sizeof(buf) / sizeof(buf[0]);
+
+ /* Read a chunk at the pointer location */
+ if (!buffer) {
+ status = ixgbe_read_ee_hostif_buffer_X550(hw, ptr, bufsz, buf);
+ if (status) {
+ DEBUGOUT("Failed to read EEPROM image\n");
+ return status;
+ }
+ local_buffer = buf;
+ } else {
+ if (buffer_size < ptr)
+ return IXGBE_ERR_PARAM;
+ local_buffer = &buffer[ptr];
+ }
+
+ if (size) {
+ start = 0;
+ length = size;
+ } else {
+ start = 1;
+ length = local_buffer[0];
+
+ /* Skip pointer section if length is invalid. */
+ if (length == 0xFFFF || length == 0 ||
+ (ptr + length) >= hw->eeprom.word_size)
+ return IXGBE_SUCCESS;
+ }
+
+ if (buffer && ((u32)start + (u32)length > buffer_size))
+ return IXGBE_ERR_PARAM;
+
+ for (i = start; length; i++, length--) {
+ if (i == bufsz && !buffer) {
+ ptr += bufsz;
+ i = 0;
+ if (length < bufsz)
+ bufsz = length;
+
+ /* Read a chunk at the pointer location */
+ status = ixgbe_read_ee_hostif_buffer_X550(hw, ptr,
+ bufsz, buf);
+ if (status) {
+ DEBUGOUT("Failed to read EEPROM image\n");
+ return status;
+ }
+ }
+ *csum += local_buffer[i];
+ }
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_calc_checksum_X550 - Calculates and returns the checksum
+ * @hw: pointer to hardware structure
+ * @buffer: pointer to buffer containing calculated checksum
+ * @buffer_size: size of buffer
+ *
+ * Returns a negative error code on error, or the 16-bit checksum
+ **/
+s32 ixgbe_calc_checksum_X550(struct ixgbe_hw *hw, u16 *buffer, u32 buffer_size)
+{
+ u16 eeprom_ptrs[IXGBE_EEPROM_LAST_WORD + 1];
+ u16 *local_buffer;
+ s32 status;
+ u16 checksum = 0;
+ u16 pointer, i, size;
+
+ DEBUGFUNC("ixgbe_calc_eeprom_checksum_X550");
+
+ hw->eeprom.ops.init_params(hw);
+
+ if (!buffer) {
+ /* Read pointer area */
+ status = ixgbe_read_ee_hostif_buffer_X550(hw, 0,
+ IXGBE_EEPROM_LAST_WORD + 1,
+ eeprom_ptrs);
+ if (status) {
+ DEBUGOUT("Failed to read EEPROM image\n");
+ return status;
+ }
+ local_buffer = eeprom_ptrs;
+ } else {
+ if (buffer_size < IXGBE_EEPROM_LAST_WORD)
+ return IXGBE_ERR_PARAM;
+ local_buffer = buffer;
+ }
+
+ /*
+ * For X550 hardware include 0x0-0x41 in the checksum, skip the
+ * checksum word itself
+ */
+ for (i = 0; i <= IXGBE_EEPROM_LAST_WORD; i++)
+ if (i != IXGBE_EEPROM_CHECKSUM)
+ checksum += local_buffer[i];
+
+ /*
+ * Include all data from pointers 0x3, 0x6-0xE. This excludes the
+ * FW, PHY module, and PCIe Expansion/Option ROM pointers.
+ */
+ for (i = IXGBE_PCIE_ANALOG_PTR_X550; i < IXGBE_FW_PTR; i++) {
+ if (i == IXGBE_PHY_PTR || i == IXGBE_OPTION_ROM_PTR)
+ continue;
+
+ pointer = local_buffer[i];
+
+ /* Skip pointer section if the pointer is invalid. */
+ if (pointer == 0xFFFF || pointer == 0 ||
+ pointer >= hw->eeprom.word_size)
+ continue;
+
+ switch (i) {
+ case IXGBE_PCIE_GENERAL_PTR:
+ size = IXGBE_IXGBE_PCIE_GENERAL_SIZE;
+ break;
+ case IXGBE_PCIE_CONFIG0_PTR:
+ case IXGBE_PCIE_CONFIG1_PTR:
+ size = IXGBE_PCIE_CONFIG_SIZE;
+ break;
+ default:
+ size = 0;
+ break;
+ }
+
+ status = ixgbe_checksum_ptr_x550(hw, pointer, size, &checksum,
+ buffer, buffer_size);
+ if (status)
+ return status;
+ }
+
+ checksum = (u16)IXGBE_EEPROM_SUM - checksum;
+
+ return (s32)checksum;
+}
+
+/**
+ * ixgbe_calc_eeprom_checksum_X550 - Calculates and returns the checksum
+ * @hw: pointer to hardware structure
+ *
+ * Returns a negative error code on error, or the 16-bit checksum
+ **/
+s32 ixgbe_calc_eeprom_checksum_X550(struct ixgbe_hw *hw)
+{
+ return ixgbe_calc_checksum_X550(hw, NULL, 0);
+}
+
+/**
+ * ixgbe_validate_eeprom_checksum_X550 - Validate EEPROM checksum
+ * @hw: pointer to hardware structure
+ * @checksum_val: calculated checksum
+ *
+ * Performs checksum calculation and validates the EEPROM checksum. If the
+ * caller does not need checksum_val, the value can be NULL.
+ **/
+s32 ixgbe_validate_eeprom_checksum_X550(struct ixgbe_hw *hw, u16 *checksum_val)
+{
+ s32 status;
+ u16 checksum;
+ u16 read_checksum = 0;
+
+ DEBUGFUNC("ixgbe_validate_eeprom_checksum_X550");
+
+ /* Read the first word from the EEPROM. If this times out or fails, do
+ * not continue or we could be in for a very long wait while every
+ * EEPROM read fails
+ */
+ status = hw->eeprom.ops.read(hw, 0, &checksum);
+ if (status) {
+ DEBUGOUT("EEPROM read failed\n");
+ return status;
+ }
+
+ status = hw->eeprom.ops.calc_checksum(hw);
+ if (status < 0)
+ return status;
+
+ checksum = (u16)(status & 0xffff);
+
+ status = ixgbe_read_ee_hostif_X550(hw, IXGBE_EEPROM_CHECKSUM,
+ &read_checksum);
+ if (status)
+ return status;
+
+ /* Verify read checksum from EEPROM is the same as
+ * calculated checksum
+ */
+ if (read_checksum != checksum) {
+ status = IXGBE_ERR_EEPROM_CHECKSUM;
+ ERROR_REPORT1(IXGBE_ERROR_INVALID_STATE,
+ "Invalid EEPROM checksum");
+ }
+
+ /* If the user cares, return the calculated checksum */
+ if (checksum_val)
+ *checksum_val = checksum;
+
+ return status;
+}
+
+/**
+ * ixgbe_update_eeprom_checksum_X550 - Updates the EEPROM checksum and flash
+ * @hw: pointer to hardware structure
+ *
+ * After writing EEPROM to shadow RAM using EEWR register, software calculates
+ * checksum and updates the EEPROM and instructs the hardware to update
+ * the flash.
+ **/
+s32 ixgbe_update_eeprom_checksum_X550(struct ixgbe_hw *hw)
+{
+ s32 status;
+ u16 checksum = 0;
+
+ DEBUGFUNC("ixgbe_update_eeprom_checksum_X550");
+
+ /* Read the first word from the EEPROM. If this times out or fails, do
+ * not continue or we could be in for a very long wait while every
+ * EEPROM read fails
+ */
+ status = ixgbe_read_ee_hostif_X550(hw, 0, &checksum);
+ if (status) {
+ DEBUGOUT("EEPROM read failed\n");
+ return status;
+ }
+
+ status = ixgbe_calc_eeprom_checksum_X550(hw);
+ if (status < 0)
+ return status;
+
+ checksum = (u16)(status & 0xffff);
+
+ status = ixgbe_write_ee_hostif_X550(hw, IXGBE_EEPROM_CHECKSUM,
+ checksum);
+ if (status)
+ return status;
+
+ status = ixgbe_update_flash_X550(hw);
+
+ return status;
+}
+
+/**
+ * ixgbe_update_flash_X550 - Instruct HW to copy EEPROM to Flash device
+ * @hw: pointer to hardware structure
+ *
+ * Issue a shadow RAM dump to FW to copy EEPROM from shadow RAM to the flash.
+ **/
+s32 ixgbe_update_flash_X550(struct ixgbe_hw *hw)
+{
+ s32 status = IXGBE_SUCCESS;
+ union ixgbe_hic_hdr2 buffer;
+
+ DEBUGFUNC("ixgbe_update_flash_X550");
+
+ buffer.req.cmd = FW_SHADOW_RAM_DUMP_CMD;
+ buffer.req.buf_lenh = 0;
+ buffer.req.buf_lenl = FW_SHADOW_RAM_DUMP_LEN;
+ buffer.req.checksum = FW_DEFAULT_CHECKSUM;
+
+ status = ixgbe_host_interface_command(hw, (u32 *)&buffer,
+ sizeof(buffer),
+ IXGBE_HI_COMMAND_TIMEOUT, false);
+
+ return status;
+}
+
+/**
+ * ixgbe_get_supported_physical_layer_X550em - Returns physical layer type
+ * @hw: pointer to hardware structure
+ *
+ * Determines physical layer capabilities of the current configuration.
+ **/
+u32 ixgbe_get_supported_physical_layer_X550em(struct ixgbe_hw *hw)
+{
+ u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN;
+ u16 ext_ability = 0;
+
+ DEBUGFUNC("ixgbe_get_supported_physical_layer_X550em");
+
+ hw->phy.ops.identify(hw);
+
+ switch (hw->phy.type) {
+ case ixgbe_phy_x550em_kr:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KR |
+ IXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ break;
+ case ixgbe_phy_x550em_kx4:
+ physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4 |
+ IXGBE_PHYSICAL_LAYER_1000BASE_KX;
+ break;
+ case ixgbe_phy_x550em_ext_t:
+ hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY,
+ IXGBE_MDIO_PMA_PMD_DEV_TYPE,
+ &ext_ability);
+ if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T;
+ if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY)
+ physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T;
+ break;
+ default:
+ break;
+ }
+
+ if (hw->mac.ops.get_media_type(hw) == ixgbe_media_type_fiber)
+ physical_layer = ixgbe_get_supported_phy_sfp_layer_generic(hw);
+
+ return physical_layer;
+}
+
+/**
+ * ixgbe_get_bus_info_x550em - Set PCI bus info
+ * @hw: pointer to hardware structure
+ *
+ * Sets bus link width and speed to unknown because X550em is
+ * not a PCI device.
+ **/
+s32 ixgbe_get_bus_info_X550em(struct ixgbe_hw *hw)
+{
+
+ DEBUGFUNC("ixgbe_get_bus_info_x550em");
+
+ hw->bus.width = ixgbe_bus_width_unknown;
+ hw->bus.speed = ixgbe_bus_speed_unknown;
+
+ hw->mac.ops.set_lan_id(hw);
+
+ return IXGBE_SUCCESS;
+}
+
+/**
+ * ixgbe_disable_rx_x550 - Disable RX unit
+ *
+ * Enables the Rx DMA unit for x550
+ **/
+void ixgbe_disable_rx_x550(struct ixgbe_hw *hw)
+{
+ u32 rxctrl, pfdtxgswc;
+ s32 status;
+ struct ixgbe_hic_disable_rxen fw_cmd;
+
+ DEBUGFUNC("ixgbe_enable_rx_dma_x550");
+
+ rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
+ if (rxctrl & IXGBE_RXCTRL_RXEN) {
+ pfdtxgswc = IXGBE_READ_REG(hw, IXGBE_PFDTXGSWC);
+ if (pfdtxgswc & IXGBE_PFDTXGSWC_VT_LBEN) {
+ pfdtxgswc &= ~IXGBE_PFDTXGSWC_VT_LBEN;
+ IXGBE_WRITE_REG(hw, IXGBE_PFDTXGSWC, pfdtxgswc);
+ hw->mac.set_lben = true;
+ } else {
+ hw->mac.set_lben = false;
+ }
+
+ fw_cmd.hdr.cmd = FW_DISABLE_RXEN_CMD;
+ fw_cmd.hdr.buf_len = FW_DISABLE_RXEN_LEN;
+ fw_cmd.hdr.checksum = FW_DEFAULT_CHECKSUM;
+ fw_cmd.port_number = (u8)hw->bus.lan_id;
+
+ status = ixgbe_host_interface_command(hw, (u32 *)&fw_cmd,
+ sizeof(struct ixgbe_hic_disable_rxen),
+ IXGBE_HI_COMMAND_TIMEOUT, true);
+
+ /* If we fail - disable RX using register write */
+ if (status) {
+ rxctrl = IXGBE_READ_REG(hw, IXGBE_RXCTRL);
+ if (rxctrl & IXGBE_RXCTRL_RXEN) {
+ rxctrl &= ~IXGBE_RXCTRL_RXEN;
+ IXGBE_WRITE_REG(hw, IXGBE_RXCTRL, rxctrl);
+ }
+ }
+ }
+}
+
+/**
+ * ixgbe_enter_lplu_x550em - Transition to low power states
+ * @hw: pointer to hardware structure
+ *
+ * Configures Low Power Link Up on transition to low power states
+ * (from D0 to non-D0). Link is required to enter LPLU so avoid resetting the
+ * X557 PHY immediately prior to entering LPLU.
+ **/
+s32 ixgbe_enter_lplu_t_x550em(struct ixgbe_hw *hw)
+{
+ u16 an_10g_cntl_reg, autoneg_reg, speed;
+ s32 status;
+ ixgbe_link_speed lcd_speed;
+ u32 save_autoneg;
+ bool link_up;
+
+ /* SW LPLU not required on later HW revisions. */
+ if ((hw->mac.type == ixgbe_mac_X550EM_x) &&
+ (IXGBE_FUSES0_REV_MASK &
+ IXGBE_READ_REG(hw, IXGBE_FUSES0_GROUP(0))))
+ return IXGBE_SUCCESS;
+
+ /* If blocked by MNG FW, then don't restart AN */
+ if (ixgbe_check_reset_blocked(hw))
+ return IXGBE_SUCCESS;
+
+ status = ixgbe_ext_phy_t_x550em_get_link(hw, &link_up);