+/**
+ * Update Redirection Table(RETA) of Receive Side Scaling of Ethernet device.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param reta_conf
+ * RETA to update.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_rss_reta_update(uint8_t port,
+ struct rte_eth_rss_reta *reta_conf);
+
+ /**
+ * Query Redirection Table(RETA) of Receive Side Scaling of Ethernet device.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param reta_conf
+ * RETA to query.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_rss_reta_query(uint8_t port,
+ struct rte_eth_rss_reta *reta_conf);
+
+ /**
+ * Updates unicast hash table for receiving packet with the given destination
+ * MAC address, and the packet is routed to all VFs for which the RX mode is
+ * accept packets that match the unicast hash table.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param addr
+ * Unicast MAC address.
+ * @param on
+ * 1 - Set an unicast hash bit for receiving packets with the MAC address.
+ * 0 - Clear an unicast hash bit.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_uc_hash_table_set(uint8_t port,struct ether_addr *addr,
+ uint8_t on);
+
+ /**
+ * Updates all unicast hash bitmaps for receiving packet with any Unicast
+ * Ethernet MAC addresses,the packet is routed to all VFs for which the RX
+ * mode is accept packets that match the unicast hash table.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param on
+ * 1 - Set all unicast hash bitmaps for receiving all the Ethernet
+ * MAC addresses
+ * 0 - Clear all unicast hash bitmaps
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_uc_all_hash_table_set(uint8_t port,uint8_t on);
+
+ /**
+ * Set RX L2 Filtering mode of a VF of an Ethernet device.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param vf
+ * VF id.
+ * @param rx_mode
+ * The RX mode mask, which is one or more of accepting Untagged Packets,
+ * packets that match the PFUTA table, Broadcast and Multicast Promiscuous.
+ * ETH_VMDQ_ACCEPT_UNTAG,ETH_VMDQ_ACCEPT_HASH_UC,
+ * ETH_VMDQ_ACCEPT_BROADCAST and ETH_VMDQ_ACCEPT_MULTICAST will be used
+ * in rx_mode.
+ * @param on
+ * 1 - Enable a VF RX mode.
+ * 0 - Disable a VF RX mode.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_set_vf_rxmode(uint8_t port, uint16_t vf, uint16_t rx_mode,
+ uint8_t on);
+
+/**
+* Enable or disable a VF traffic transmit of the Ethernet device.
+*
+* @param port
+* The port identifier of the Ethernet device.
+* @param vf
+* VF id.
+* @param on
+* 1 - Enable a VF traffic transmit.
+* 0 - Disable a VF traffic transmit.
+* @return
+* - (0) if successful.
+* - (-ENODEV) if *port_id* invalid.
+* - (-ENOTSUP) if hardware doesn't support.
+* - (-EINVAL) if bad parameter.
+*/
+int
+rte_eth_dev_set_vf_tx(uint8_t port,uint16_t vf, uint8_t on);
+
+/**
+* Enable or disable a VF traffic receive of an Ethernet device.
+*
+* @param port
+* The port identifier of the Ethernet device.
+* @param vf
+* VF id.
+* @param on
+* 1 - Enable a VF traffic receive.
+* 0 - Disable a VF traffic receive.
+* @return
+* - (0) if successful.
+* - (-ENOTSUP) if hardware doesn't support.
+* - (-ENODEV) if *port_id* invalid.
+* - (-EINVAL) if bad parameter.
+*/
+int
+rte_eth_dev_set_vf_rx(uint8_t port,uint16_t vf, uint8_t on);
+
+/**
+* Enable/Disable hardware VF VLAN filtering by an Ethernet device of
+* received VLAN packets tagged with a given VLAN Tag Identifier.
+*
+* @param port id
+* The port identifier of the Ethernet device.
+* @param vlan_id
+* The VLAN Tag Identifier whose filtering must be enabled or disabled.
+* @param vf_mask
+* Bitmap listing which VFs participate in the VLAN filtering.
+* @param vlan_on
+* 1 - Enable VFs VLAN filtering.
+* 0 - Disable VFs VLAN filtering.
+* @return
+* - (0) if successful.
+* - (-ENOTSUP) if hardware doesn't support.
+* - (-ENODEV) if *port_id* invalid.
+* - (-EINVAL) if bad parameter.
+*/
+int
+rte_eth_dev_set_vf_vlan_filter(uint8_t port, uint16_t vlan_id,
+ uint64_t vf_mask,
+ uint8_t vlan_on);
+
+/**
+ * Set a traffic mirroring rule on an Ethernet device
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param mirror_conf
+ * The pointer to the traffic mirroring structure describing the mirroring rule.
+ * The *rte_eth_vm_mirror_conf* structure includes the type of mirroring rule,
+ * destination pool and the value of rule if enable vlan or pool mirroring.
+ *
+ * @param rule_id
+ * The index of traffic mirroring rule, we support four separated rules.
+ * @param on
+ * 1 - Enable a mirroring rule.
+ * 0 - Disable a mirroring rule.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the mr_conf information is not correct.
+ */
+int rte_eth_mirror_rule_set(uint8_t port_id,
+ struct rte_eth_vmdq_mirror_conf *mirror_conf,
+ uint8_t rule_id,
+ uint8_t on);
+
+/**
+ * Reset a traffic mirroring rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param rule_id
+ * The index of traffic mirroring rule, we support four separated rules.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_mirror_rule_reset(uint8_t port_id,
+ uint8_t rule_id);
+
+/**
+ * Set the rate limitation for a queue on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param queue_idx
+ * The queue id.
+ * @param tx_rate
+ * The tx rate allocated from the total link speed for this queue.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_set_queue_rate_limit(uint8_t port_id, uint16_t queue_idx,
+ uint16_t tx_rate);
+
+/**
+ * Set the rate limitation for a vf on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param vf
+ * VF id.
+ * @param tx_rate
+ * The tx rate allocated from the total link speed for this VF id.
+ * @param q_msk
+ * The queue mask which need to set the rate.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this feature.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_set_vf_rate_limit(uint8_t port_id, uint16_t vf,
+ uint16_t tx_rate, uint64_t q_msk);
+
+/**
+ * Initialize bypass logic. This function needs to be called before
+ * executing any other bypass API.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_init(uint8_t port);
+
+/**
+ * Return bypass state.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param state
+ * The return bypass state.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_state_show(uint8_t port, uint32_t *state);
+
+/**
+ * Set bypass state
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param state
+ * The current bypass state.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_state_set(uint8_t port, uint32_t *new_state);
+
+/**
+ * Return bypass state when given event occurs.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param event
+ * The bypass event
+ * - (1) Main power on (power button is pushed)
+ * - (2) Auxiliary power on (power supply is being plugged)
+ * - (3) Main power off (system shutdown and power supply is left plugged in)
+ * - (4) Auxiliary power off (power supply is being unplugged)
+ * - (5) Display or set the watchdog timer
+ * @param state
+ * The bypass state when given event occurred.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_event_show(uint8_t port, uint32_t event, uint32_t *state);
+
+/**
+ * Set bypass state when given event occurs.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param event
+ * The bypass event
+ * - (1) Main power on (power button is pushed)
+ * - (2) Auxiliary power on (power supply is being plugged)
+ * - (3) Main power off (system shutdown and power supply is left plugged in)
+ * - (4) Auxiliary power off (power supply is being unplugged)
+ * - (5) Display or set the watchdog timer
+ * @param state
+ * The assigned state when given event occurs.
+ * - (1) Normal mode
+ * - (2) Bypass mode
+ * - (3) Isolate mode
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_event_store(uint8_t port, uint32_t event, uint32_t state);
+
+/**
+ * Set bypass watchdog timeout count.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param state
+ * The timeout to be set.
+ * - (0) 0 seconds (timer is off)
+ * - (1) 1.5 seconds
+ * - (2) 2 seconds
+ * - (3) 3 seconds
+ * - (4) 4 seconds
+ * - (5) 8 seconds
+ * - (6) 16 seconds
+ * - (7) 32 seconds
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_wd_timeout_store(uint8_t port, uint32_t timeout);
+
+/**
+ * Get bypass firmware version.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param ver
+ * The firmware version
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_ver_show(uint8_t port, uint32_t *ver);
+
+/**
+ * Return bypass watchdog timeout in seconds
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param wd_timeout
+ * The return watchdog timeout. "0" represents timer expired
+ * - (0) 0 seconds (timer is off)
+ * - (1) 1.5 seconds
+ * - (2) 2 seconds
+ * - (3) 3 seconds
+ * - (4) 4 seconds
+ * - (5) 8 seconds
+ * - (6) 16 seconds
+ * - (7) 32 seconds
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_wd_timeout_show(uint8_t port, uint32_t *wd_timeout);
+
+/**
+ * Reset bypass watchdog timer
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_bypass_wd_reset(uint8_t port);
+
+ /**
+ * Configuration of Receive Side Scaling hash computation of Ethernet device.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param rss_conf
+ * The new configuration to use for RSS hash computation on the port.
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_rss_hash_update(uint8_t port_id,
+ struct rte_eth_rss_conf *rss_conf);
+
+ /**
+ * Retrieve current configuration of Receive Side Scaling hash computation
+ * of Ethernet device.
+ *
+ * @param port
+ * The port identifier of the Ethernet device.
+ * @param rss_conf
+ * Where to store the current RSS hash configuration of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support RSS.
+ */
+int
+rte_eth_dev_rss_hash_conf_get(uint8_t port_id,
+ struct rte_eth_rss_conf *rss_conf);
+
+ /**
+ * Add UDP tunneling port of an Ethernet device for filtering a specific
+ * tunneling packet by UDP port number.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param tunnel_udp
+ * UDP tunneling configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ */
+int
+rte_eth_dev_udp_tunnel_add(uint8_t port_id,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+
+ /**
+ * Detete UDP tunneling port configuration of Ethernet device
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param tunnel_udp
+ * UDP tunneling configuration.
+ *
+ * @return
+ * - (0) if successful.
+ * - (-ENODEV) if port identifier is invalid.
+ * - (-ENOTSUP) if hardware doesn't support tunnel type.
+ */
+int
+rte_eth_dev_udp_tunnel_delete(uint8_t port_id,
+ struct rte_eth_udp_tunnel *tunnel_udp);
+
+/**
+ * add syn filter
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param rx_queue
+ * The index of RX queue where to store RX packets matching the syn filter.
+ * @param filter
+ * The pointer to the structure describing the syn filter rule.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_add_syn_filter(uint8_t port_id,
+ struct rte_syn_filter *filter, uint16_t rx_queue);
+
+/**
+ * remove syn filter
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_remove_syn_filter(uint8_t port_id);
+
+/**
+ * get syn filter
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param filter
+ * The pointer to the structure describing the syn filter.
+ * @param rx_queue
+ * A pointer to get the queue index of syn filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-EINVAL) if bad parameter.
+ */
+int rte_eth_dev_get_syn_filter(uint8_t port_id,
+ struct rte_syn_filter *filter, uint16_t *rx_queue);
+
+/**
+ * Add a new ethertype filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of ethertype filter.
+ * @param filter
+ * The pointer to the structure describing the ethertype filter rule.
+ * The *rte_ethertype_filter* structure includes the values of the different
+ * fields to match: ethertype and priority in vlan tag.
+ * priority in vlan tag is not supported for E1000 dev.
+ * @param rx_queue
+ * The index of the RX queue where to store RX packets matching the added
+ * ethertype filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support ethertype filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_add_ethertype_filter(uint8_t port_id, uint16_t index,
+ struct rte_ethertype_filter *filter, uint16_t rx_queue);
+
+/**
+ * remove an ethertype filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of ethertype filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support ethertype filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_remove_ethertype_filter(uint8_t port_id,
+ uint16_t index);
+
+/**
+ * Get an ethertype filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of ethertype filter.
+ * @param filter
+ * A pointer to a structure of type *rte_ethertype_filter* to be filled with
+ * the information of the Ethertype filter.
+ * @param rx_queue
+ * A pointer to get the queue index.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support ethertype filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ * - (-ENOENT) if no enabled filter in this index.
+ */
+int rte_eth_dev_get_ethertype_filter(uint8_t port_id, uint16_t index,
+ struct rte_ethertype_filter *filter, uint16_t *rx_queue);
+
+/**
+ * Add a new 2tuple filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of 2tuple filter.
+ * @param filter
+ * The pointer to the structure describing the 2tuple filter rule.
+ * The *rte_2tuple_filter* structure includes the values of the different
+ * fields to match: protocol, dst_port and
+ * tcp_flags if the protocol is tcp type.
+ * @param rx_queue
+ * The index of the RX queue where to store RX packets matching the added
+ * 2tuple filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support 2tuple filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_add_2tuple_filter(uint8_t port_id, uint16_t index,
+ struct rte_2tuple_filter *filter, uint16_t rx_queue);
+
+/**
+ * remove a 2tuple filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of 2tuple filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support 2tuple filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_remove_2tuple_filter(uint8_t port_id, uint16_t index);
+
+/**
+ * Get an 2tuple filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of 2tuple filter.
+ * @param filter
+ * A pointer to a structure of type *rte_2tuple_filter* to be filled with
+ * the information of the 2tuple filter.
+ * @param rx_queue
+ * A pointer to get the queue index.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support 2tuple filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ * - (-ENOENT) if no enabled filter in this index.
+ */
+int rte_eth_dev_get_2tuple_filter(uint8_t port_id, uint16_t index,
+ struct rte_2tuple_filter *filter, uint16_t *rx_queue);
+
+/**
+ * Add a new 5tuple filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of 5tuple filter.
+ * @param filter
+ * The pointer to the structure describing the 5tuple filter rule.
+ * The *rte_5tuple_filter* structure includes the values of the different
+ * fields to match: dst src IP, dst src port, protocol and relative masks
+ * @param rx_queue
+ * The index of the RX queue where to store RX packets matching the added
+ * 5tuple filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support 5tuple filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_add_5tuple_filter(uint8_t port_id, uint16_t index,
+ struct rte_5tuple_filter *filter, uint16_t rx_queue);
+
+/**
+ * remove a 5tuple filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of 5tuple filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support 5tuple filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_remove_5tuple_filter(uint8_t port_id, uint16_t index);
+
+/**
+ * Get an 5tuple filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of 5tuple filter.
+ * @param filter
+ * A pointer to a structure of type *rte_5tuple_filter* to be filled with
+ * the information of the 5tuple filter.
+ * @param rx_queue
+ * A pointer to get the queue index.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support 5tuple filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_get_5tuple_filter(uint8_t port_id, uint16_t index,
+ struct rte_5tuple_filter *filter, uint16_t *rx_queue);
+
+/**
+ * Add a new flex filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of flex filter.
+ * @param filter
+ * The pointer to the structure describing the flex filter rule.
+ * The *rte_flex_filter* structure includes the values of the different fields
+ * to match: the dwords (first len bytes of packet ) and relative masks.
+ * @param rx_queue
+ * The index of the RX queue where to store RX packets matching the added
+ * flex filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support flex filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ * - (-ENOENT) if no enabled filter in this index.
+ */
+int rte_eth_dev_add_flex_filter(uint8_t port_id, uint16_t index,
+ struct rte_flex_filter *filter, uint16_t rx_queue);
+
+/**
+ * remove a flex filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of flex filter.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support flex filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ */
+int rte_eth_dev_remove_flex_filter(uint8_t port_id, uint16_t index);
+
+/**
+ * Get an flex filter rule on an Ethernet device.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param index
+ * The identifier of flex filter.
+ * @param filter
+ * A pointer to a structure of type *rte_flex_filter* to be filled with
+ * the information of the flex filter.
+ * @param rx_queue
+ * A pointer to get the queue index.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support flex filter.
+ * - (-ENODEV) if *port_id* invalid.
+ * - (-EINVAL) if the filter information is not correct.
+ * - (-ENOENT) if no enabled filter in this index.
+ */
+int rte_eth_dev_get_flex_filter(uint8_t port_id, uint16_t index,
+ struct rte_flex_filter *filter, uint16_t *rx_queue);
+
+/**
+ * Check whether the filter type is supported on an Ethernet device.
+ * All the supported filter types are defined in 'rte_eth_ctrl.h'.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param filter_type
+ * Filter type.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support this filter type.
+ * - (-ENODEV) if *port_id* invalid.
+ */
+int rte_eth_dev_filter_supported(uint8_t port_id, enum rte_filter_type filter_type);
+
+/**
+ * Take operations to assigned filter type on an Ethernet device.
+ * All the supported operations and filter types are defined in 'rte_eth_ctrl.h'.
+ *
+ * @param port_id
+ * The port identifier of the Ethernet device.
+ * @param filter_type
+ * Filter type.
+ * @param filter_op
+ * Type of operation.
+ * @param arg
+ * A pointer to arguments defined specifically for the operation.
+ * @return
+ * - (0) if successful.
+ * - (-ENOTSUP) if hardware doesn't support.
+ * - (-ENODEV) if *port_id* invalid.
+ * - others depends on the specific operations implementation.
+ */
+int rte_eth_dev_filter_ctrl(uint8_t port_id, enum rte_filter_type filter_type,
+ enum rte_filter_op filter_op, void *arg);