+/**
+ * RX packet is a 802.1q VLAN packet. This flag was set by PMDs when
+ * the packet is recognized as a VLAN, but the behavior between PMDs
+ * was not the same. This flag is kept for some time to avoid breaking
+ * applications and should be replaced by PKT_RX_VLAN_STRIPPED.
+ */
+#define PKT_RX_VLAN_PKT (1ULL << 0)
+
+#define PKT_RX_RSS_HASH (1ULL << 1) /**< RX packet with RSS hash result. */
+#define PKT_RX_FDIR (1ULL << 2) /**< RX packet with FDIR match indicate. */
+
+/**
+ * Deprecated.
+ * Checking this flag alone is deprecated: check the 2 bits of
+ * PKT_RX_L4_CKSUM_MASK.
+ * This flag was set when the L4 checksum of a packet was detected as
+ * wrong by the hardware.
+ */
+#define PKT_RX_L4_CKSUM_BAD (1ULL << 3)
+
+/**
+ * Deprecated.
+ * Checking this flag alone is deprecated: check the 2 bits of
+ * PKT_RX_IP_CKSUM_MASK.
+ * This flag was set when the IP checksum of a packet was detected as
+ * wrong by the hardware.
+ */
+#define PKT_RX_IP_CKSUM_BAD (1ULL << 4)
+
+#define PKT_RX_EIP_CKSUM_BAD (1ULL << 5) /**< External IP header checksum error. */
+
+/**
+ * A vlan has been stripped by the hardware and its tci is saved in
+ * mbuf->vlan_tci. This can only happen if vlan stripping is enabled
+ * in the RX configuration of the PMD.
+ */
+#define PKT_RX_VLAN_STRIPPED (1ULL << 6)
+
+/**
+ * Mask of bits used to determine the status of RX IP checksum.
+ * - PKT_RX_IP_CKSUM_UNKNOWN: no information about the RX IP checksum
+ * - PKT_RX_IP_CKSUM_BAD: the IP checksum in the packet is wrong
+ * - PKT_RX_IP_CKSUM_GOOD: the IP checksum in the packet is valid
+ * - PKT_RX_IP_CKSUM_NONE: the IP checksum is not correct in the packet
+ * data, but the integrity of the IP header is verified.
+ */
+#define PKT_RX_IP_CKSUM_MASK ((1ULL << 4) | (1ULL << 7))
+
+#define PKT_RX_IP_CKSUM_UNKNOWN 0
+#define PKT_RX_IP_CKSUM_BAD (1ULL << 4)
+#define PKT_RX_IP_CKSUM_GOOD (1ULL << 7)
+#define PKT_RX_IP_CKSUM_NONE ((1ULL << 4) | (1ULL << 7))
+
+/**
+ * Mask of bits used to determine the status of RX L4 checksum.
+ * - PKT_RX_L4_CKSUM_UNKNOWN: no information about the RX L4 checksum
+ * - PKT_RX_L4_CKSUM_BAD: the L4 checksum in the packet is wrong
+ * - PKT_RX_L4_CKSUM_GOOD: the L4 checksum in the packet is valid
+ * - PKT_RX_L4_CKSUM_NONE: the L4 checksum is not correct in the packet
+ * data, but the integrity of the L4 data is verified.
+ */
+#define PKT_RX_L4_CKSUM_MASK ((1ULL << 3) | (1ULL << 8))
+
+#define PKT_RX_L4_CKSUM_UNKNOWN 0
+#define PKT_RX_L4_CKSUM_BAD (1ULL << 3)
+#define PKT_RX_L4_CKSUM_GOOD (1ULL << 8)
+#define PKT_RX_L4_CKSUM_NONE ((1ULL << 3) | (1ULL << 8))
+
+#define PKT_RX_IEEE1588_PTP (1ULL << 9) /**< RX IEEE1588 L2 Ethernet PT Packet. */
+#define PKT_RX_IEEE1588_TMST (1ULL << 10) /**< RX IEEE1588 L2/L4 timestamped packet.*/
+#define PKT_RX_FDIR_ID (1ULL << 13) /**< FD id reported if FDIR match. */
+#define PKT_RX_FDIR_FLX (1ULL << 14) /**< Flexible bytes reported if FDIR match. */
+
+/**
+ * The 2 vlans have been stripped by the hardware and their tci are
+ * saved in mbuf->vlan_tci (inner) and mbuf->vlan_tci_outer (outer).
+ * This can only happen if vlan stripping is enabled in the RX
+ * configuration of the PMD. If this flag is set, PKT_RX_VLAN_STRIPPED
+ * must also be set.
+ */
+#define PKT_RX_QINQ_STRIPPED (1ULL << 15)
+
+/**
+ * Deprecated.
+ * RX packet with double VLAN stripped.
+ * This flag is replaced by PKT_RX_QINQ_STRIPPED.
+ */
+#define PKT_RX_QINQ_PKT PKT_RX_QINQ_STRIPPED
+
+/**
+ * When packets are coalesced by a hardware or virtual driver, this flag
+ * can be set in the RX mbuf, meaning that the m->tso_segsz field is
+ * valid and is set to the segment size of original packets.
+ */
+#define PKT_RX_LRO (1ULL << 16)
+
+/* add new RX flags here */
+
+/* add new TX flags here */
+
+/**
+ * Offload the MACsec. This flag must be set by the application to enable
+ * this offload feature for a packet to be transmitted.
+ */
+#define PKT_TX_MACSEC (1ULL << 44)
+
+/**
+ * Bits 45:48 used for the tunnel type.
+ * When doing Tx offload like TSO or checksum, the HW needs to configure the
+ * tunnel type into the HW descriptors.
+ */
+#define PKT_TX_TUNNEL_VXLAN (0x1ULL << 45)
+#define PKT_TX_TUNNEL_GRE (0x2ULL << 45)
+#define PKT_TX_TUNNEL_IPIP (0x3ULL << 45)
+#define PKT_TX_TUNNEL_GENEVE (0x4ULL << 45)
+/* add new TX TUNNEL type here */
+#define PKT_TX_TUNNEL_MASK (0xFULL << 45)
+
+/**
+ * Second VLAN insertion (QinQ) flag.
+ */
+#define PKT_TX_QINQ_PKT (1ULL << 49) /**< TX packet with double VLAN inserted. */
+
+/**
+ * TCP segmentation offload. To enable this offload feature for a
+ * packet to be transmitted on hardware supporting TSO:
+ * - set the PKT_TX_TCP_SEG flag in mbuf->ol_flags (this flag implies
+ * PKT_TX_TCP_CKSUM)
+ * - set the flag PKT_TX_IPV4 or PKT_TX_IPV6
+ * - if it's IPv4, set the PKT_TX_IP_CKSUM flag and write the IP checksum
+ * to 0 in the packet
+ * - fill the mbuf offload information: l2_len, l3_len, l4_len, tso_segsz
+ * - calculate the pseudo header checksum without taking ip_len in account,
+ * and set it in the TCP header. Refer to rte_ipv4_phdr_cksum() and
+ * rte_ipv6_phdr_cksum() that can be used as helpers.
+ */
+#define PKT_TX_TCP_SEG (1ULL << 50)
+
+#define PKT_TX_IEEE1588_TMST (1ULL << 51) /**< TX IEEE1588 packet to timestamp. */
+
+/**
+ * Bits 52+53 used for L4 packet type with checksum enabled: 00: Reserved,
+ * 01: TCP checksum, 10: SCTP checksum, 11: UDP checksum. To use hardware
+ * L4 checksum offload, the user needs to:
+ * - fill l2_len and l3_len in mbuf
+ * - set the flags PKT_TX_TCP_CKSUM, PKT_TX_SCTP_CKSUM or PKT_TX_UDP_CKSUM
+ * - set the flag PKT_TX_IPV4 or PKT_TX_IPV6
+ * - calculate the pseudo header checksum and set it in the L4 header (only
+ * for TCP or UDP). See rte_ipv4_phdr_cksum() and rte_ipv6_phdr_cksum().
+ * For SCTP, set the crc field to 0.
+ */
+#define PKT_TX_L4_NO_CKSUM (0ULL << 52) /**< Disable L4 cksum of TX pkt. */
+#define PKT_TX_TCP_CKSUM (1ULL << 52) /**< TCP cksum of TX pkt. computed by NIC. */
+#define PKT_TX_SCTP_CKSUM (2ULL << 52) /**< SCTP cksum of TX pkt. computed by NIC. */
+#define PKT_TX_UDP_CKSUM (3ULL << 52) /**< UDP cksum of TX pkt. computed by NIC. */
+#define PKT_TX_L4_MASK (3ULL << 52) /**< Mask for L4 cksum offload request. */
+
+/**
+ * Offload the IP checksum in the hardware. The flag PKT_TX_IPV4 should
+ * also be set by the application, although a PMD will only check
+ * PKT_TX_IP_CKSUM.
+ * - set the IP checksum field in the packet to 0
+ * - fill the mbuf offload information: l2_len, l3_len
+ */
+#define PKT_TX_IP_CKSUM (1ULL << 54)
+
+/**
+ * Packet is IPv4. This flag must be set when using any offload feature
+ * (TSO, L3 or L4 checksum) to tell the NIC that the packet is an IPv4
+ * packet. If the packet is a tunneled packet, this flag is related to
+ * the inner headers.
+ */
+#define PKT_TX_IPV4 (1ULL << 55)
+
+/**
+ * Packet is IPv6. This flag must be set when using an offload feature
+ * (TSO or L4 checksum) to tell the NIC that the packet is an IPv6
+ * packet. If the packet is a tunneled packet, this flag is related to
+ * the inner headers.
+ */
+#define PKT_TX_IPV6 (1ULL << 56)
+
+#define PKT_TX_VLAN_PKT (1ULL << 57) /**< TX packet is a 802.1q VLAN packet. */
+
+/**
+ * Offload the IP checksum of an external header in the hardware. The
+ * flag PKT_TX_OUTER_IPV4 should also be set by the application, alto ugh
+ * a PMD will only check PKT_TX_IP_CKSUM. The IP checksum field in the
+ * packet must be set to 0.
+ * - set the outer IP checksum field in the packet to 0
+ * - fill the mbuf offload information: outer_l2_len, outer_l3_len
+ */
+#define PKT_TX_OUTER_IP_CKSUM (1ULL << 58)
+
+/**
+ * Packet outer header is IPv4. This flag must be set when using any
+ * outer offload feature (L3 or L4 checksum) to tell the NIC that the
+ * outer header of the tunneled packet is an IPv4 packet.
+ */
+#define PKT_TX_OUTER_IPV4 (1ULL << 59)
+
+/**
+ * Packet outer header is IPv6. This flag must be set when using any
+ * outer offload feature (L4 checksum) to tell the NIC that the outer
+ * header of the tunneled packet is an IPv6 packet.
+ */
+#define PKT_TX_OUTER_IPV6 (1ULL << 60)
+
+/**
+ * Bitmask of all supported packet Tx offload features flags,
+ * which can be set for packet.
+ */
+#define PKT_TX_OFFLOAD_MASK ( \
+ PKT_TX_IP_CKSUM | \
+ PKT_TX_L4_MASK | \
+ PKT_TX_OUTER_IP_CKSUM | \
+ PKT_TX_TCP_SEG | \
+ PKT_TX_IEEE1588_TMST | \
+ PKT_TX_QINQ_PKT | \
+ PKT_TX_VLAN_PKT | \
+ PKT_TX_TUNNEL_MASK | \
+ PKT_TX_MACSEC)
+
+#define __RESERVED (1ULL << 61) /**< reserved for future mbuf use */
+
+#define IND_ATTACHED_MBUF (1ULL << 62) /**< Indirect attached mbuf */