+
+/* Due to a hw errata, if the host tries to configure the VFTA register
+ * while performing queries from the BMC or DMA, then the VFTA in some
+ * cases won't be written.
+ */
+
+/**
+ * e1000_clear_vfta_i350 - Clear VLAN filter table
+ * @hw: pointer to the HW structure
+ *
+ * Clears the register array which contains the VLAN filter table by
+ * setting all the values to 0.
+ **/
+void e1000_clear_vfta_i350(struct e1000_hw *hw)
+{
+ u32 offset;
+ int i;
+
+ DEBUGFUNC("e1000_clear_vfta_350");
+
+ for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
+ for (i = 0; i < 10; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, 0);
+
+ E1000_WRITE_FLUSH(hw);
+ }
+}
+
+/**
+ * e1000_write_vfta_i350 - Write value to VLAN filter table
+ * @hw: pointer to the HW structure
+ * @offset: register offset in VLAN filter table
+ * @value: register value written to VLAN filter table
+ *
+ * Writes value at the given offset in the register array which stores
+ * the VLAN filter table.
+ **/
+void e1000_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value)
+{
+ int i;
+
+ DEBUGFUNC("e1000_write_vfta_350");
+
+ for (i = 0; i < 10; i++)
+ E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value);
+
+ E1000_WRITE_FLUSH(hw);
+}
+
+
+/**
+ * e1000_set_i2c_bb - Enable I2C bit-bang
+ * @hw: pointer to the HW structure
+ *
+ * Enable I2C bit-bang interface
+ *
+ **/
+s32 e1000_set_i2c_bb(struct e1000_hw *hw)
+{
+ s32 ret_val = E1000_SUCCESS;
+ u32 ctrl_ext, i2cparams;
+
+ DEBUGFUNC("e1000_set_i2c_bb");
+
+ ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT);
+ ctrl_ext |= E1000_CTRL_I2C_ENA;
+ E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext);
+ E1000_WRITE_FLUSH(hw);
+
+ i2cparams = E1000_READ_REG(hw, E1000_I2CPARAMS);
+ i2cparams |= E1000_I2CBB_EN;
+ i2cparams |= E1000_I2C_DATA_OE_N;
+ i2cparams |= E1000_I2C_CLK_OE_N;
+ E1000_WRITE_REG(hw, E1000_I2CPARAMS, i2cparams);
+ E1000_WRITE_FLUSH(hw);
+
+ return ret_val;
+}
+
+/**
+ * e1000_read_i2c_byte_generic - Reads 8 bit word over I2C
+ * @hw: pointer to hardware structure
+ * @byte_offset: byte offset to read
+ * @dev_addr: device address
+ * @data: value read
+ *
+ * Performs byte read operation over I2C interface at
+ * a specified device address.
+ **/
+s32 e1000_read_i2c_byte_generic(struct e1000_hw *hw, u8 byte_offset,
+ u8 dev_addr, u8 *data)
+{
+ s32 status = E1000_SUCCESS;
+ u32 max_retry = 10;
+ u32 retry = 1;
+ u16 swfw_mask = 0;
+
+ bool nack = true;
+
+ DEBUGFUNC("e1000_read_i2c_byte_generic");
+
+ swfw_mask = E1000_SWFW_PHY0_SM;
+
+ do {
+ if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)
+ != E1000_SUCCESS) {
+ status = E1000_ERR_SWFW_SYNC;
+ goto read_byte_out;
+ }
+
+ e1000_i2c_start(hw);
+
+ /* Device Address and write indication */
+ status = e1000_clock_out_i2c_byte(hw, dev_addr);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_get_i2c_ack(hw);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_clock_out_i2c_byte(hw, byte_offset);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_get_i2c_ack(hw);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ e1000_i2c_start(hw);
+
+ /* Device Address and read indication */
+ status = e1000_clock_out_i2c_byte(hw, (dev_addr | 0x1));
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_get_i2c_ack(hw);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_clock_in_i2c_byte(hw, data);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_clock_out_i2c_bit(hw, nack);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ e1000_i2c_stop(hw);
+ break;
+
+fail:
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+ msec_delay(100);
+ e1000_i2c_bus_clear(hw);
+ retry++;
+ if (retry < max_retry)
+ DEBUGOUT("I2C byte read error - Retrying.\n");
+ else
+ DEBUGOUT("I2C byte read error.\n");
+
+ } while (retry < max_retry);
+
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+
+read_byte_out:
+
+ return status;
+}
+
+/**
+ * e1000_write_i2c_byte_generic - Writes 8 bit word over I2C
+ * @hw: pointer to hardware structure
+ * @byte_offset: byte offset to write
+ * @dev_addr: device address
+ * @data: value to write
+ *
+ * Performs byte write operation over I2C interface at
+ * a specified device address.
+ **/
+s32 e1000_write_i2c_byte_generic(struct e1000_hw *hw, u8 byte_offset,
+ u8 dev_addr, u8 data)
+{
+ s32 status = E1000_SUCCESS;
+ u32 max_retry = 1;
+ u32 retry = 0;
+ u16 swfw_mask = 0;
+
+ DEBUGFUNC("e1000_write_i2c_byte_generic");
+
+ swfw_mask = E1000_SWFW_PHY0_SM;
+
+ if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask) != E1000_SUCCESS) {
+ status = E1000_ERR_SWFW_SYNC;
+ goto write_byte_out;
+ }
+
+ do {
+ e1000_i2c_start(hw);
+
+ status = e1000_clock_out_i2c_byte(hw, dev_addr);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_get_i2c_ack(hw);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_clock_out_i2c_byte(hw, byte_offset);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_get_i2c_ack(hw);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_clock_out_i2c_byte(hw, data);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ status = e1000_get_i2c_ack(hw);
+ if (status != E1000_SUCCESS)
+ goto fail;
+
+ e1000_i2c_stop(hw);
+ break;
+
+fail:
+ e1000_i2c_bus_clear(hw);
+ retry++;
+ if (retry < max_retry)
+ DEBUGOUT("I2C byte write error - Retrying.\n");
+ else
+ DEBUGOUT("I2C byte write error.\n");
+ } while (retry < max_retry);
+
+ hw->mac.ops.release_swfw_sync(hw, swfw_mask);
+
+write_byte_out:
+
+ return status;
+}
+
+/**
+ * e1000_i2c_start - Sets I2C start condition
+ * @hw: pointer to hardware structure
+ *
+ * Sets I2C start condition (High -> Low on SDA while SCL is High)
+ **/
+STATIC void e1000_i2c_start(struct e1000_hw *hw)
+{
+ u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+
+ DEBUGFUNC("e1000_i2c_start");
+
+ /* Start condition must begin with data and clock high */
+ e1000_set_i2c_data(hw, &i2cctl, 1);
+ e1000_raise_i2c_clk(hw, &i2cctl);
+
+ /* Setup time for start condition (4.7us) */
+ usec_delay(E1000_I2C_T_SU_STA);
+
+ e1000_set_i2c_data(hw, &i2cctl, 0);
+
+ /* Hold time for start condition (4us) */
+ usec_delay(E1000_I2C_T_HD_STA);
+
+ e1000_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us */
+ usec_delay(E1000_I2C_T_LOW);
+
+}
+
+/**
+ * e1000_i2c_stop - Sets I2C stop condition
+ * @hw: pointer to hardware structure
+ *
+ * Sets I2C stop condition (Low -> High on SDA while SCL is High)
+ **/
+STATIC void e1000_i2c_stop(struct e1000_hw *hw)
+{
+ u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+
+ DEBUGFUNC("e1000_i2c_stop");
+
+ /* Stop condition must begin with data low and clock high */
+ e1000_set_i2c_data(hw, &i2cctl, 0);
+ e1000_raise_i2c_clk(hw, &i2cctl);
+
+ /* Setup time for stop condition (4us) */
+ usec_delay(E1000_I2C_T_SU_STO);
+
+ e1000_set_i2c_data(hw, &i2cctl, 1);
+
+ /* bus free time between stop and start (4.7us)*/
+ usec_delay(E1000_I2C_T_BUF);
+}
+
+/**
+ * e1000_clock_in_i2c_byte - Clocks in one byte via I2C
+ * @hw: pointer to hardware structure
+ * @data: data byte to clock in
+ *
+ * Clocks in one byte data via I2C data/clock
+ **/
+STATIC s32 e1000_clock_in_i2c_byte(struct e1000_hw *hw, u8 *data)
+{
+ s32 i;
+ bool bit = 0;
+
+ DEBUGFUNC("e1000_clock_in_i2c_byte");
+
+ *data = 0;
+ for (i = 7; i >= 0; i--) {
+ e1000_clock_in_i2c_bit(hw, &bit);
+ *data |= bit << i;
+ }
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_clock_out_i2c_byte - Clocks out one byte via I2C
+ * @hw: pointer to hardware structure
+ * @data: data byte clocked out
+ *
+ * Clocks out one byte data via I2C data/clock
+ **/
+STATIC s32 e1000_clock_out_i2c_byte(struct e1000_hw *hw, u8 data)
+{
+ s32 status = E1000_SUCCESS;
+ s32 i;
+ u32 i2cctl;
+ bool bit = 0;
+
+ DEBUGFUNC("e1000_clock_out_i2c_byte");
+
+ for (i = 7; i >= 0; i--) {
+ bit = (data >> i) & 0x1;
+ status = e1000_clock_out_i2c_bit(hw, bit);
+
+ if (status != E1000_SUCCESS)
+ break;
+ }
+
+ /* Release SDA line (set high) */
+ i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+
+ i2cctl |= E1000_I2C_DATA_OE_N;
+ E1000_WRITE_REG(hw, E1000_I2CPARAMS, i2cctl);
+ E1000_WRITE_FLUSH(hw);
+
+ return status;
+}
+
+/**
+ * e1000_get_i2c_ack - Polls for I2C ACK
+ * @hw: pointer to hardware structure
+ *
+ * Clocks in/out one bit via I2C data/clock
+ **/
+STATIC s32 e1000_get_i2c_ack(struct e1000_hw *hw)
+{
+ s32 status = E1000_SUCCESS;
+ u32 i = 0;
+ u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+ u32 timeout = 10;
+ bool ack = true;
+
+ DEBUGFUNC("e1000_get_i2c_ack");
+
+ e1000_raise_i2c_clk(hw, &i2cctl);
+
+ /* Minimum high period of clock is 4us */
+ usec_delay(E1000_I2C_T_HIGH);
+
+ /* Wait until SCL returns high */
+ for (i = 0; i < timeout; i++) {
+ usec_delay(1);
+ i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+ if (i2cctl & E1000_I2C_CLK_IN)
+ break;
+ }
+ if (!(i2cctl & E1000_I2C_CLK_IN))
+ return E1000_ERR_I2C;
+
+ ack = e1000_get_i2c_data(&i2cctl);
+ if (ack) {
+ DEBUGOUT("I2C ack was not received.\n");
+ status = E1000_ERR_I2C;
+ }
+
+ e1000_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us */
+ usec_delay(E1000_I2C_T_LOW);
+
+ return status;
+}
+
+/**
+ * e1000_clock_in_i2c_bit - Clocks in one bit via I2C data/clock
+ * @hw: pointer to hardware structure
+ * @data: read data value
+ *
+ * Clocks in one bit via I2C data/clock
+ **/
+STATIC s32 e1000_clock_in_i2c_bit(struct e1000_hw *hw, bool *data)
+{
+ u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+
+ DEBUGFUNC("e1000_clock_in_i2c_bit");
+
+ e1000_raise_i2c_clk(hw, &i2cctl);
+
+ /* Minimum high period of clock is 4us */
+ usec_delay(E1000_I2C_T_HIGH);
+
+ i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+ *data = e1000_get_i2c_data(&i2cctl);
+
+ e1000_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us */
+ usec_delay(E1000_I2C_T_LOW);
+
+ return E1000_SUCCESS;
+}
+
+/**
+ * e1000_clock_out_i2c_bit - Clocks in/out one bit via I2C data/clock
+ * @hw: pointer to hardware structure
+ * @data: data value to write
+ *
+ * Clocks out one bit via I2C data/clock
+ **/
+STATIC s32 e1000_clock_out_i2c_bit(struct e1000_hw *hw, bool data)
+{
+ s32 status;
+ u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+
+ DEBUGFUNC("e1000_clock_out_i2c_bit");
+
+ status = e1000_set_i2c_data(hw, &i2cctl, data);
+ if (status == E1000_SUCCESS) {
+ e1000_raise_i2c_clk(hw, &i2cctl);
+
+ /* Minimum high period of clock is 4us */
+ usec_delay(E1000_I2C_T_HIGH);
+
+ e1000_lower_i2c_clk(hw, &i2cctl);
+
+ /* Minimum low period of clock is 4.7 us.
+ * This also takes care of the data hold time.
+ */
+ usec_delay(E1000_I2C_T_LOW);
+ } else {
+ status = E1000_ERR_I2C;
+ DEBUGOUT1("I2C data was not set to %X\n", data);
+ }
+
+ return status;
+}
+/**
+ * e1000_raise_i2c_clk - Raises the I2C SCL clock
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ *
+ * Raises the I2C clock line '0'->'1'
+ **/
+STATIC void e1000_raise_i2c_clk(struct e1000_hw *hw, u32 *i2cctl)
+{
+ DEBUGFUNC("e1000_raise_i2c_clk");
+
+ *i2cctl |= E1000_I2C_CLK_OUT;
+ *i2cctl &= ~E1000_I2C_CLK_OE_N;
+ E1000_WRITE_REG(hw, E1000_I2CPARAMS, *i2cctl);
+ E1000_WRITE_FLUSH(hw);
+
+ /* SCL rise time (1000ns) */
+ usec_delay(E1000_I2C_T_RISE);
+}
+
+/**
+ * e1000_lower_i2c_clk - Lowers the I2C SCL clock
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ *
+ * Lowers the I2C clock line '1'->'0'
+ **/
+STATIC void e1000_lower_i2c_clk(struct e1000_hw *hw, u32 *i2cctl)
+{
+
+ DEBUGFUNC("e1000_lower_i2c_clk");
+
+ *i2cctl &= ~E1000_I2C_CLK_OUT;
+ *i2cctl &= ~E1000_I2C_CLK_OE_N;
+ E1000_WRITE_REG(hw, E1000_I2CPARAMS, *i2cctl);
+ E1000_WRITE_FLUSH(hw);
+
+ /* SCL fall time (300ns) */
+ usec_delay(E1000_I2C_T_FALL);
+}
+
+/**
+ * e1000_set_i2c_data - Sets the I2C data bit
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ * @data: I2C data value (0 or 1) to set
+ *
+ * Sets the I2C data bit
+ **/
+STATIC s32 e1000_set_i2c_data(struct e1000_hw *hw, u32 *i2cctl, bool data)
+{
+ s32 status = E1000_SUCCESS;
+
+ DEBUGFUNC("e1000_set_i2c_data");
+
+ if (data)
+ *i2cctl |= E1000_I2C_DATA_OUT;
+ else
+ *i2cctl &= ~E1000_I2C_DATA_OUT;
+
+ *i2cctl &= ~E1000_I2C_DATA_OE_N;
+ *i2cctl |= E1000_I2C_CLK_OE_N;
+ E1000_WRITE_REG(hw, E1000_I2CPARAMS, *i2cctl);
+ E1000_WRITE_FLUSH(hw);
+
+ /* Data rise/fall (1000ns/300ns) and set-up time (250ns) */
+ usec_delay(E1000_I2C_T_RISE + E1000_I2C_T_FALL + E1000_I2C_T_SU_DATA);
+
+ *i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+ if (data != e1000_get_i2c_data(i2cctl)) {
+ status = E1000_ERR_I2C;
+ DEBUGOUT1("Error - I2C data was not set to %X.\n", data);
+ }
+
+ return status;
+}
+
+/**
+ * e1000_get_i2c_data - Reads the I2C SDA data bit
+ * @hw: pointer to hardware structure
+ * @i2cctl: Current value of I2CCTL register
+ *
+ * Returns the I2C data bit value
+ **/
+STATIC bool e1000_get_i2c_data(u32 *i2cctl)
+{
+ bool data;
+
+ DEBUGFUNC("e1000_get_i2c_data");
+
+ if (*i2cctl & E1000_I2C_DATA_IN)
+ data = 1;
+ else
+ data = 0;
+
+ return data;
+}
+
+/**
+ * e1000_i2c_bus_clear - Clears the I2C bus
+ * @hw: pointer to hardware structure
+ *
+ * Clears the I2C bus by sending nine clock pulses.
+ * Used when data line is stuck low.
+ **/
+void e1000_i2c_bus_clear(struct e1000_hw *hw)
+{
+ u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS);
+ u32 i;
+
+ DEBUGFUNC("e1000_i2c_bus_clear");
+
+ e1000_i2c_start(hw);
+
+ e1000_set_i2c_data(hw, &i2cctl, 1);
+
+ for (i = 0; i < 9; i++) {
+ e1000_raise_i2c_clk(hw, &i2cctl);
+
+ /* Min high period of clock is 4us */
+ usec_delay(E1000_I2C_T_HIGH);
+
+ e1000_lower_i2c_clk(hw, &i2cctl);
+
+ /* Min low period of clock is 4.7us*/
+ usec_delay(E1000_I2C_T_LOW);
+ }
+
+ e1000_i2c_start(hw);
+
+ /* Put the i2c bus back to default state */
+ e1000_i2c_stop(hw);
+}
+