static void i40e_configure_registers(struct i40e_hw *hw);
static void i40e_hw_init(struct i40e_hw *hw);
static void i40e_configure_registers(struct i40e_hw *hw);
static void i40e_hw_init(struct i40e_hw *hw);
#define RTE_PCI_DEV_ID_DECL_I40E(vend, dev) {RTE_PCI_DEVICE(vend, dev)},
#include "rte_pci_dev_ids.h"
{ .vendor_id = 0, /* sentinel */ },
};
#define RTE_PCI_DEV_ID_DECL_I40E(vend, dev) {RTE_PCI_DEVICE(vend, dev)},
#include "rte_pci_dev_ids.h"
{ .vendor_id = 0, /* sentinel */ },
};
.dev_configure = i40e_dev_configure,
.dev_start = i40e_dev_start,
.dev_stop = i40e_dev_stop,
.dev_configure = i40e_dev_configure,
.dev_start = i40e_dev_start,
.dev_stop = i40e_dev_stop,
struct i40e_hw *hw = I40E_DEV_PRIVATE_TO_HW(dev->data->dev_private);
struct i40e_link_status link_status;
struct rte_eth_link link, old;
int status;
struct i40e_hw *hw = I40E_DEV_PRIVATE_TO_HW(dev->data->dev_private);
struct i40e_link_status link_status;
struct rte_eth_link link, old;
int status;
memset(&link, 0, sizeof(link));
memset(&old, 0, sizeof(old));
memset(&link_status, 0, sizeof(link_status));
rte_i40e_dev_atomic_read_link_status(dev, &old);
memset(&link, 0, sizeof(link));
memset(&old, 0, sizeof(old));
memset(&link_status, 0, sizeof(link_status));
rte_i40e_dev_atomic_read_link_status(dev, &old);
- /* Get link status information from hardware */
- status = i40e_aq_get_link_info(hw, false, &link_status, NULL);
- if (status != I40E_SUCCESS) {
- link.link_speed = ETH_LINK_SPEED_100;
- link.link_duplex = ETH_LINK_FULL_DUPLEX;
- PMD_DRV_LOG(ERR, "Failed to get link info");
- goto out;
- }
+ do {
+ /* Get link status information from hardware */
+ status = i40e_aq_get_link_info(hw, false, &link_status, NULL);
+ if (status != I40E_SUCCESS) {
+ link.link_speed = ETH_LINK_SPEED_100;
+ link.link_duplex = ETH_LINK_FULL_DUPLEX;
+ PMD_DRV_LOG(ERR, "Failed to get link info");
+ goto out;
+ }
- /* Configure switch ID */
- ctxt.info.valid_sections |=
- rte_cpu_to_le_16(I40E_AQ_VSI_PROP_SWITCH_VALID);
- ctxt.info.switch_id =
- rte_cpu_to_le_16(I40E_AQ_VSI_SW_ID_FLAG_ALLOW_LB);
+ /**
+ * Do not configure switch ID to enable VEB switch by
+ * I40E_AQ_VSI_SW_ID_FLAG_ALLOW_LB. Because in Fortville,
+ * if the source mac address of packet sent from VF is not
+ * listed in the VEB's mac table, the VEB will switch the
+ * packet back to the VF. Need to enable it when HW issue
+ * is fixed.
+ */
+
/* Configure port/vlan */
ctxt.info.valid_sections |=
rte_cpu_to_le_16(I40E_AQ_VSI_PROP_VLAN_VALID);
/* Configure port/vlan */
ctxt.info.valid_sections |=
rte_cpu_to_le_16(I40E_AQ_VSI_PROP_VLAN_VALID);