FPGA 5GNR FEC PMD supports the following features:
+- LDPC Encode in the DL
+- LDPC Decode in the UL
- 8 VFs per PF (physical device)
- Maximum of 32 UL queues per VF
- Maximum of 32 DL queues per VF
- MSI-X
- SR-IOV
+FPGA 5GNR FEC PMD supports the following BBDEV capabilities:
+
+* For the LDPC encode operation:
+ - ``RTE_BBDEV_LDPC_CRC_24B_ATTACH`` : set to attach CRC24B to CB(s)
+ - ``RTE_BBDEV_LDPC_RATE_MATCH`` : if set then do not do Rate Match bypass
+
+* For the LDPC decode operation:
+ - ``RTE_BBDEV_LDPC_CRC_TYPE_24B_CHECK`` : check CRC24B from CB(s)
+ - ``RTE_BBDEV_LDPC_ITERATION_STOP_ENABLE`` : disable early termination
+ - ``RTE_BBDEV_LDPC_CRC_TYPE_24B_DROP`` : drops CRC24B bits appended while decoding
+ - ``RTE_BBDEV_LDPC_HQ_COMBINE_IN_ENABLE`` : provides an input for HARQ combining
+ - ``RTE_BBDEV_LDPC_HQ_COMBINE_OUT_ENABLE`` : provides an input for HARQ combining
+ - ``RTE_BBDEV_LDPC_INTERNAL_HARQ_MEMORY_IN_ENABLE`` : HARQ memory input is internal
+ - ``RTE_BBDEV_LDPC_INTERNAL_HARQ_MEMORY_OUT_ENABLE`` : HARQ memory output is internal
+ - ``RTE_BBDEV_LDPC_INTERNAL_HARQ_MEMORY_LOOPBACK`` : loopback data to/from HARQ memory
+ - ``RTE_BBDEV_LDPC_INTERNAL_HARQ_MEMORY_FILLERS`` : HARQ memory includes the fillers bits
+
+
Limitations
-----------
.. code-block:: console
echo <num-of-vfs> > /sys/bus/pci/devices/0000\:<b>\:<d>.<f>/sriov_numvfs
+
+
+Configure the VFs through PF
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The PCI virtual functions must be configured before working or getting assigned
+to VMs/Containers. The configuration involves allocating the number of hardware
+queues, priorities, load balance, bandwidth and other settings necessary for the
+device to perform FEC functions.
+
+This configuration needs to be executed at least once after reboot or PCI FLR and can
+be achieved by using the function ``fpga_5gnr_fec_configure()``, which sets up the
+parameters defined in ``fpga_5gnr_fec_conf`` structure:
+
+.. code-block:: c
+
+ struct fpga_5gnr_fec_conf {
+ bool pf_mode_en;
+ uint8_t vf_ul_queues_number[FPGA_5GNR_FEC_NUM_VFS];
+ uint8_t vf_dl_queues_number[FPGA_5GNR_FEC_NUM_VFS];
+ uint8_t ul_bandwidth;
+ uint8_t dl_bandwidth;
+ uint8_t ul_load_balance;
+ uint8_t dl_load_balance;
+ uint16_t flr_time_out;
+ };
+
+- ``pf_mode_en``: identifies whether only PF is to be used, or the VFs. PF and
+ VFs are mutually exclusive and cannot run simultaneously.
+ Set to 1 for PF mode enabled.
+ If PF mode is enabled all queues available in the device are assigned
+ exclusively to PF and 0 queues given to VFs.
+
+- ``vf_*l_queues_number``: defines the hardware queue mapping for every VF.
+
+- ``*l_bandwidth``: in case of congestion on PCIe interface. The device
+ allocates different bandwidth to UL and DL. The weight is configured by this
+ setting. The unit of weight is 3 code blocks. For example, if the code block
+ cbps (code block per second) ratio between UL and DL is 12:1, then the
+ configuration value should be set to 36:3. The schedule algorithm is based
+ on code block regardless the length of each block.
+
+- ``*l_load_balance``: hardware queues are load-balanced in a round-robin
+ fashion. Queues get filled first-in first-out until they reach a pre-defined
+ watermark level, if exceeded, they won't get assigned new code blocks..
+ This watermark is defined by this setting.
+
+ If all hardware queues exceeds the watermark, no code blocks will be
+ streamed in from UL/DL code block FIFO.
+
+- ``flr_time_out``: specifies how many 16.384us to be FLR time out. The
+ time_out = flr_time_out x 16.384us. For instance, if you want to set 10ms for
+ the FLR time out then set this setting to 0x262=610.
+
+
+An example configuration code calling the function ``fpga_5gnr_fec_configure()`` is shown
+below:
+
+.. code-block:: c
+
+ struct fpga_5gnr_fec_conf conf;
+ unsigned int i;
+
+ memset(&conf, 0, sizeof(struct fpga_5gnr_fec_conf));
+ conf.pf_mode_en = 1;
+
+ for (i = 0; i < FPGA_5GNR_FEC_NUM_VFS; ++i) {
+ conf.vf_ul_queues_number[i] = 4;
+ conf.vf_dl_queues_number[i] = 4;
+ }
+ conf.ul_bandwidth = 12;
+ conf.dl_bandwidth = 5;
+ conf.dl_load_balance = 64;
+ conf.ul_load_balance = 64;
+
+ /* setup FPGA PF */
+ ret = fpga_5gnr_fec_configure(info->dev_name, &conf);
+ TEST_ASSERT_SUCCESS(ret,
+ "Failed to configure 4G FPGA PF for bbdev %s",
+ info->dev_name);
+
+
+Test Application
+----------------
+
+BBDEV provides a test application, ``test-bbdev.py`` and range of test data for testing
+the functionality of FPGA 5GNR FEC encode and decode, depending on the device's
+capabilities. The test application is located under app->test-bbdev folder and has the
+following options:
+
+.. code-block:: console
+
+ "-p", "--testapp-path": specifies path to the bbdev test app.
+ "-e", "--eal-params" : EAL arguments which are passed to the test app.
+ "-t", "--timeout" : Timeout in seconds (default=300).
+ "-c", "--test-cases" : Defines test cases to run. Run all if not specified.
+ "-v", "--test-vector" : Test vector path (default=dpdk_path+/app/test-bbdev/test_vectors/bbdev_null.data).
+ "-n", "--num-ops" : Number of operations to process on device (default=32).
+ "-b", "--burst-size" : Operations enqueue/dequeue burst size (default=32).
+ "-l", "--num-lcores" : Number of lcores to run (default=16).
+ "-i", "--init-device" : Initialise PF device with default values.
+
+
+To execute the test application tool using simple decode or encode data,
+type one of the following:
+
+.. code-block:: console
+
+ ./test-bbdev.py -c validation -n 64 -b 1 -v ./ldpc_dec_default.data
+ ./test-bbdev.py -c validation -n 64 -b 1 -v ./ldpc_enc_default.data
+
+
+The test application ``test-bbdev.py``, supports the ability to configure the PF device with
+a default set of values, if the "-i" or "- -init-device" option is included. The default values
+are defined in test_bbdev_perf.c as:
+
+- VF_UL_QUEUE_VALUE 4
+- VF_DL_QUEUE_VALUE 4
+- UL_BANDWIDTH 3
+- DL_BANDWIDTH 3
+- UL_LOAD_BALANCE 128
+- DL_LOAD_BALANCE 128
+- FLR_TIMEOUT 610
+
+
+Test Vectors
+~~~~~~~~~~~~
+
+In addition to the simple LDPC decoder and LDPC encoder tests, bbdev also provides
+a range of additional tests under the test_vectors folder, which may be useful. The results
+of these tests will depend on the FPGA 5GNR FEC capabilities.
git.droids-corp.org / dpdk.git / blobdiff